Pneumatic Actuator Products

Cylinders, Guided Cylinders and Rotary Actuators

Catalog 0900P-4
Catalog 0900P-4 Pneumatic Actuator Products
Global Pneumatics, Warning, Offer of Sale

This icon can be found next to products that are widely

supported by Parker Pneumatics’ worldwide manufacturing
and sales network. When you see this icon, you can
be confident that this product is manufactured and/or
stocked* worldwide for rapid delivery. In addition to local
manufacturing or inventory, our sales network has been
specifically trained on these products to provide our
customers with the best possible service.

Global Products not showing this icon are still sold and distributed
Pneumatics worldwide. However, The Global Pneumatics icon represents
products that customers can expect the best level of support.

If you are a multi-national company, seek global sourcing or

ship globally, depend on Parker Pneumatic for PREMIER
CUSTOMER SERVICE.

* Stocking levels vary by country

! WARNING
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN
OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide
product and/or system options for further investigation by users h aving technical expertise. It is important that you analyze all
aspects of your application including consequences of any failure, and review the information concerning the product or system
in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the
user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and
assuring that all performance, safety and warning requirements of the application are met.
The products described herein, including without limitation, product features, specifications, designs, availability and pricing,
are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice.

Offer of Sale
The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its
authorized distributors. This offer and its acceptance are governed by the provisions stated on the separate page of this
document entitled “Offer of Sale”.
© Copyright 2008 Parker Hannifin Corporation. All Rights Reserved

Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Pneumatic Actuator Products
Index Product Selection Chart

Engineering
Application Engineering Data A

Data
3MA/4MA Series, 3MAJ/4MAJ Series, 2MNR Series,
B

Cylinders
Tie Rod
Tie Rod Cylinders ACVB Option, LPSO Option, 2A/2AN Series,
S Series, C Series

Cylinders
ISO Cylinders C

ISO
P1D Series, P1A Series

Round Body
Cylinders
Round Body Cylinders
SR Series, SRM Series, SRD/SRDM Series, SRX Series,
P1L Series, P Series D
P1M Series, P1M Series with Tooling Plate,

Cylinders
Compact
Compact Cylinders P1M Series Swing Clamp,
LP/LPM Series, C05 Series, P1G Series
E

Cylinders
F

Guided
P5T Series, P5T2 Series, P5TT/TD, P5L Series,
Guided Cylinders HB Series, P5E Series

Cylinders
G

Rodless
Rodless Cylinders P1X Series, RC Series, P1Z Series

Cylinders
H

Rotary
PV Series, PRN(A) Series, WR Series, PTR Series,
Rotary Actuators B671/F672 Series, HP Series, P5W Series

Pneumatic
Grippers
Pneumatic Grippers
For Complete Information,
Refer to Catalog 1900-2 J

Air Motors
Air Motors PV1S
K
Complementary

L
Products

Linear Alignment Couplers, Flow Controls, 3TK Air Oil Tanks,

Complementary Products RL Series, Shock Absorbers, Transition Kits
Electronic

M
Sensors

Electronic Sensors Solid State, Reed and Proximity Sensors

Safety Guide,
Offer of Sale
Fax Forms,

, Safety Guide,
Fax Forms
O
Application FAX Forms
N
 Parker Hannifin Corporation
Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
ISO Pneumatic
Cylinders

Section C

P1D
P1A

C1 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4
Section C Overview

Section C – ISO Pneumatic Cylinders

ISO / VDMA Tie Rod Cylinders

P1D Series
• Conforms to ISO 6431/ISO15552/VDMA 24562
• Flexible Design With 3 Major Versions (Standard, Clean, and Removable Gland)
• Standard Version – Performance at an Affordable Price

C • Removable Gland Version – Performance, Ease of Maintenance and Customization

at all Bore Sizes
• Clean Version – For Applications Requiring High Cleanliness and Sanitary Standards
• Rod Lock Options Available
• 10 Bar (145 PSI) Air Service

Mini-ISO Cylinders
P1A Series (Non-Repairable)
• Conforms to ISO 6432 and CETOP RP52P Standards
• Stainless Steel Body with Black Anodized Aluminum End Caps
• Stainless Steel Piston Rod
• Magnetic Piston and Bumpers Standard
• 5 Bore Sizes, 10mm through 25mm
• 10 Bar (145 PSI) Air Service

Also in the Guided Cylinders Section:

P5E Series
• Low Profile Guided Assembly
• Powered by the P1D Cylinder
• Bore Sizes 32, 40, 50, 63, 80 and 100mm
• Rod Lock Options Available
• 10 Bar (145 PSI) Air Service
HB Series
• Medium Duty to Extremely Heavy Duty Linear Motion
• Powered by the P1D Cylinder
• Bore Sizes 40, 50, and 63mm
• Rod Lock Options Available
• 10 Bar (145 PSI) Air Service with Other Options Available

C2 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 P1D Series
ISO 6431 / ISO 15552 / VDMA 24562
Pneumatic Cylinders

P1D
P1A

Contents
Features.............................................................................C4 Rod End Dimensions........................................................C21
Versions / Options........................................................ C5-C7 Duplex (3 & 4-Position) Cylinder Dimensions...................C22
Ordering Information.................................................... C8-C9 Cylinder Mountings................................................... C23-C29
Specifications........................................................... C10-C11 Piston Rod Mountings.............................................. C30-C31
Technical Data.......................................................... C12-C14 Accessories......................................................................C32
Cylinder Dimensions................................................. C15-C20 Service Kits......................................................................C33

C3 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Air Cylinders
Features P1D Series
C086
P1D Standard Version All P1D Versions
The aluminum cylinder Rod seals and piston have a magnetic
Polyurethane end- seals are polyurethane
body extrusion is piston as standard.
of-stroke bumpers for maximized service
anodized inside and
are standard. They life.
Aluminum heads and outside for long life and
provide noise
caps are anodized and low friction. High strength
dampening from
designed to eliminate steel fastener
impact and act as
cavities or pockets connects the
durable end seals.
where water and dirt piston to the
could collect. piston rod and
is secured
Zinc-plated in place with
fasteners for tough
C
anaerobic
environments are adhesive.
standard. Sealing
plugs and stainless
steel fasteners
are available as
options.

The cushioning has

individual flow geometry
for each cylinder size.
This provides effective
cushioning which is
easier to set and adjust.
All P1D Versions
(except for the Tie
Rod Version) have All P1D Versions utilize
an extruded alumi- a transparent, non-
num profile cylinder toxic, food-grade grease
All P1D versions have P1D Standard Version is body with integrated that is entirely free from
One piston rod case hardened and constructed entirely sensor grooves that PTFE and silicone.
nut according chome-plated steel without copper, PTFE accept the Global
to ISO 439B piston rods as standard. and silicone – decisive Sensor family with-
is included as Chrome-plated stainless for certain industries. out the need for an
standard. steel is also available. additional mounting
bracket.

P1D Standard Version

P1D Standard Version cylinders are available in 32- drop into the sensor groove quickly and easily. Both the
125mm bores and utilize internal composite technology cable and the sensor are protected. Choose a sensor
to save weight, while assuring the high performance in a variety of cable lengths and with flying leads, 8mm
connector or 12mm connector.
and functionality expected of ISO cylinders. Cushions
and bumpers at both ends and a magnetic piston are Optimized cushioning
included as standard. The Standard Version serves all Thanks to the plastic inserts in the end covers, each
markets where performance at an affordable price is cylinder bore has been given individual flow geometry.
desired. This provides optimized cushioning, which is quicker
International standards and easier­ to set and adjust.
The new P1D Series complies with the current Smooth, quiet operation and long service life
ISO 6431, ISO/DIS 15552, VDMA 24562 and AFNOR All seals and end-of-stroke bumpers are made from
installation dimensional standards for customer polyurethane (PUR), the bearings and piston are made
reassurance world-wide. from proven engineering plastics with excellent bearing
properties and all cylinders are greased at the factory
Mechanically protected sensor technology with a transparent, food-grade grease. Altogether, this
The body extrusion has recessed sensor grooves on gives the P1D Series very long service life and smooth,
three sides of the cylinder. The new Global Sensors quiet operation­.

C4 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Air Cylinders
Versions P1D Series
C086
P1D Series Rod Lock Cylinder
The P1D Series Rod Lock Cylinder incorporates a
powerful piston rod locking device, which clamps the
piston rod and locks it in position. The locking device is a
spring lock with an air pressure release and is integrated
into the front (head) cover of the cylinder.
In the absence of air signal pressure, full holding force
is applied to the piston rod. When air is present at 4 Bar
(58 psi), the locking device is released.
The P1D Series Rod Lock Cylinder is available for
P1D Removable Gland Version
P1D Removable Gland Version cylinders are available
cylinder bores 32-125mm. The design provides several
valuable characteristics, such as: C
• A holding force corresponding to a pressure of 7 Bar
in 32-200mm bores and utilize bar stock endcaps and a
(102 psi)
removable high-strength bronze bearing for traditional

P1D
and custom applications. The bronze bearing assembly • A clean design, with the front (head) end cover and
is externally removable for quick and easy maintenance. locking device built into a common block for compact
No other ISO cylinder manufacturer in the world installation

P1A
produces a Removable Gland Version and meets these • Easy to clean, well-sealed construction
demands. This version covers all applications which • Exhaust air from the locking device can be
require performance and customization at all bore sizes. piped away when there are high demands for a
Removable Gland contaminant free environment
An extra-long inboard bearing surface ensures
lubrication from within the cylinder. Outboard of the
bearing are two leak-proof seals. The rod wiper seal
wipes away any dirt on the rod. This means less wear
on bearing surfaces and internal parts. The result is
positive, no-leak sealing, regardless of conditions. And
with the famous Parker removable style gland, you can
replace the rod seals and/or bearings when necessary
without disassembling the rest of the cylinder and
without the need of any special wrenches.
Aluminum Piston Option
For high temperature applications, an aluminum piston
is available with fluorocarbon seals. The piston is
threaded onto the piston rod and secured in place with
anaerobic adhesive which is temperature sensitive.
For applications above +121°C (+250°F) specify a
pinned piston to rod connection. The polyurethane P1D Series Rod Lock Cylinder
seals that are standard on the nylon piston are also an with Manual Override
available option with the aluminum piston. The magnet The P1D Series Rod Lock Cylinder with Manual
that is cleverly hidden underneath the wear-band Override is available for rod lock release during non-
is also a standard feature on the aluminum piston. production activities. It incorporates the same features
The durable wear-band prevents any metal-to-metal as the standard rod lock cylinder.
contact between the piston and the cylinder body wall
increasing the overall life of the cylinder.
Machined End Caps with Captive Cushion Screw
Adjustment
The end caps are made of precision lightweight
aluminum. This allows for maximum flexibility and quick
manufacturing for any customization that is required.
The end caps also feature a captive cushion needle
valve adjustment screw for optimized cushioning that is
inherent throughout the P1D family of ISO cylinders.

C5 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Air Cylinders
Versions P1D Series
C086
Cushioning screw with positive geometry
Convex shape for optimum hygiene To offer the best hygiene properties, the
What makes the P1D Clean version unique projecting cushioning screw is sealed against
is its convex body extrusion, which allows the end cover. This eliminates dirt-collecting Up to four integral
the cylinder to be kept clean. Regardless cavities and gives the best hygiene, since it is sensors
of orientation, fluids will run off the cylinder so easy to clean. Cylinders for two integral
body surfaces. sensors have two
undivided camshafts
along the entire stroke.
Sealing plugs Free choice of cable
Plastic sealing plugs are exit, front or rear. There
installed in the end cover is also a version with

C
screws which are not used divided camshafts for up
for the cylinder installation. to four sensors, which are
To ensure the sealing installed two from each
function, the plugs cannot end cover, with cable
be re-used. When installed exiting both front and rear.
in the end cover screws,
they are tapped lightly with
a hammer for high axial
Patent applied for system of integrated
force.
standard sensors
The Clean Version of the P1D cylinder
has a system of sensors, which are fully
integrated into the body extrusion to give
the cylinders a clean external design. Up to
P1D Clean Version four sensors chosen from the range of P1D
standard sensors, can be mounted in two
The P1D Clean Version is completely designed for the food industry. dedicated grooves beneath a transparent,
The stringent requirements for hygiene regarding choice of material and sealed molding. Tightening the stop screw
corrosion resistance have guided the development of this cylinder version. onto the cam shaft will lock each sensor­ in
Available with BSPP ports (ISO 1179-1 with ISO 228-1 threads). the desired position. The sensor LEDs are
always fully visible, which facilitates initial
All the main dimensions of the P1D Clean comply with ISO 6431, ISO/DIS set-up, adjustment and trouble-shooting. The
1555, VDMA 24562 and AFNOR­ standards except the somewhat larger entire sensor system has a hose-proof design
footprint of the end covers and envelope of the body extrusion, due to the equivalent to IP65.
hygienic, convex, easy-to-clean geometry of the cushioning adjustment­
screw and the components of the integrated sensor system.

P1D Tie-Rod Version 32-125mm bores

The P1D Tie-Rod Version cylinders are based on the
same high level technology as the Standard Version.
They accept either Standard Version or Removable
Gland Version heads and caps. This cylinder is the
perfect choice wherever a true tie-rod cylinder is needed.
International standards
The P1D Tie-Rod Version complies with ISO 6431,
ISO/DIS 15552, VDMA 24562 and AFNOR
installation dimension standards, for customer
reassurance world-wide.
“Drop-in” sensor
The P1D Tie-Rod Version utilizes the same drop-in
Global Sensors as the other versions. An ingenious
multi-jointed adapter clamps the sensors to the tie rod in
any chosen position along the stroke.
Large Bore Sizes
The P1D Tie-Rod Version is now available in 160
and 200mm bore sizes.

C6 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Air Cylinders
Cylinder Options P1D Series
C086
Using P1D cylinders as a platform, a number of different
designs can be produced to suit differing requirements.
Please refer to the Ordering Information page for the
designation of each variant­.
Alternative piston rod materials
All P1D cylinders in all bores, Ø32-200 mm, can be
ordered with the following piston rod materials:
– Steel, hard chrome plated (standard)
– Stainless steel, hard chrome plated Alternative Piston Rod Materials
– Acid proof steel

Double rod cylinders C

All bore sizes of all versions are available with a double
rod. Cylinders with a double rod can take higher side

P1D
forces thanks to the double support for the piston rod.
In addition, this design makes it easier to install external
mechanical position sensors as well as giving equal
force and flow on both sides of the piston.

P1A
Double Rod
High ambient temperature
The Removable Gland Version can be supplied in
special high ambient temperature version. The cylinders
have seal systems, materials and grease for elevated
temperature ranges. The high temperature version
does not have a magnetic piston (no function at high
temperatures). The aluminum piston option is required
for service above +80°C (+176°F) and a pinned
piston to rod connection is required for service
above +121°C (+250°F).
Ambient temperature range: High Ambient Temperature
-10°C to +121°C, peaks up to +150°C
(+14°F to +250°F, peaks up to +300°F).

Low pressure hydraulics

All bore sizes of the Removable Gland Version can
be supplied with special seals for operation with low
pressure hydraulics up to 10 bar. Temperature range
-20 °C to +80 °C (-4°F to +176°F).

Duplex cylinder – 3 and 4 position cylinders

By installing two cylinders with the same or different 3 and 4 Position Cylinders
stroke, it is possible to build a working unit with three or
four positions. This type of unit is available as factory-
fitted P1D Tie-Rod Version cylinders in all bore sizes.
Other P1D cylinders can be flange mounted back-to-
back with a special mounting.

Tandem cylinder
The P1D Tie-Rod Version is also available as a tandem
cylinder, i.e. two cylinders connected in series. This
cylinder unit has almost twice the force, which is a great Tandem Cylinders
advantage in restricted spaces.

Guided Cylinders
For guided versions of the P1D, see the P5E Series and
HB Series in Section F.

P5E Series HB Series

C7 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 (Revised 03-23-09) Air Cylinders
Ordering Information P1D Series
C086

P1D – S 032 M C – ➡
Continued
Piston Style Bore Size on next
page
Piston Material 032 32mm
Cushions
Composite 1 Aluminum 2 040 40mm
None M Y 050 50mm
Cush B/E –3 4 063 63mm
080 80mm
Cush head J 5
100 100mm Cylinder Ports
Cush cap K 6
C 1 Not available for 160-200mm bores.
2 Not available on Clean Version.
125
160
125mm
160mm 8
Front & Rear
– BSPP Ports (G Threads)**
3 Must be placed in model code. 200 200mm 8 E NPTF Ports*
Q BSPT Ports (RC Threads)*
8 Tie Rod Version E
must be specified * Not available on Clean
for these bores.
Version.
Version ** ISO 1179-1 with ISO 228-1
threads.
Rod Lock
Cylinder
Body Fitted Fitted w/Manual
Profile None w/Std Override
Rod Lock 7 Rod Lock 7
Standard S L N/A
Die Cast End Caps 4 Tie Rod 14 T M N/A
Clean C D N/A 9 Applies only to end cover
Removable Gland 5 Standard G R J screws for 32-125mm bores.
(Machined Endcaps) Tie Rod 14 E 74 Consult Factory For stainless steel tie rods and
6 nuts (all bore sizes), change
Special Any Special / Version to special and request
4 Not available for 160-200mm bores or with fluorocarbon seals. stainless steel tie rods and
5 When Removable Gland Version is fitted with rod lock, gland cannot nuts.
be replaced without disassembling cylinder. 10 If used for temperature
6 If special cylinder is ordered (other than rod end), End Cap Style, above +80°C (+176°F),
aluminum piston required.
Cylinder Body Profile and Rod Lock option must be given in addition to the
special request. Not available with die cast
end caps. Fluorocarbon seals
7 Cylinders fitted with rod locks must be cushioned on both ends.
for Rod Lock Versions are
for chemical compatibility
applications only, not for high
Function temperature.
Fastener Type Rod Wiper Double Double 11 Hydraulic seal option valid for
Tandem 14
Style Acting Rod Removable Gland Version only.
Standard end Std scraper M F C Adjustable cushion options and
cover screws Metal scraper Q R J Rod Lock Versions not avail-
able.
Stainless steel Std scraper A G N/A
end cover screws 9 12 Not available on Clean Version.
Metal scraper S T N/A
13 Only available on Clean
Version.
14 Tie Rod Version is required for
Piston Rod & Seal Material Tandem Function.
Piston Rod Material Seal Material
Standard Fluorocarbon 10 Hydraulic 11
Chrome plated carbon steel 12 C G J
Chrome plated stainless steel 12 R D Z
Stainless steel 13 S N/A N/A
Acid-resistant stainless steel M N 12 N/A

C8 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Air Cylinders
Ordering Information P1D Series
C086

0500 N N N N N

Stroke 1
Specify whole mm
Rod End
using 4 digits, i.e.
0500 N Metric male
6 Metric female
3 Special*
Rod Mountings & Plugs 2
* Please provide desired

C
Rod Mounting No Plugs 3 With Plugs 4
dimensions for KK, AM
Swivel rod eye S A and WH. If otherwise
Swivel rod eye SS T 1 special, provide
Swivel rod eye with clevis dimensioned sketch.
V E

P1D
bracket GA
Swivel rod eye SS with clevis
W 2
bracket GA
Sensors 5
Clevis C B

P1A
Cable Location
Clevis SS D 3 Prepared for Factory-fitted
Sensors Front Rear or Front &
Flexco coupling F G or Left Right Rear
One additional piston rod nut X P P1D Clean Version 6 7 8
Stainless steel piston rod nut Y 4 P1D all versions (except Clean)
Acid-resistant nut Z 5 prepared for sensors or Clean N
Version without sensor capability 6
None (piston rod nut only) N R

Notes:
Mounting Style
1 When specifying a stop tube, place a “/”
in the version field. Then specify the Standard Rotated 90°
version, amount of stop tube and Flange MF1 at head (front) end 1 3
amount of net stroke. The stroke used in Flange MF2 at cap (rear) end B 4
the model code should be gross stroke
Flanges MF1 and MF2 at both ends 2 K
(net stroke plus stop tube).
Foot brackets MS1 F R
2 Please review Piston Rod Selection
Clevis bracket GA aluminum C U
Chart in the Engineering Section to
check for a rod buckling condition. Rear eye MP4 aluminum E V
Rear swivel eye MP6 aluminum S W
3 Clean Version comes standard with plugs.
Use this column when ordering Clean Version. Clevis bracket MP2 aluminum T Y
Rear eye + clevis (MP4 + MP2) aluminum L Z
4 Not available for 160-200mm bores.
Clevis bracket MP2 + pivot hinge aluminum X 5
5 For sensor part numbers and specifications,
Clevis bracket GA aluminum + steel swivel hinge Q 0
please refer to Electronic Sensors section.
Rear swivel eye + clevis bracket
6 P1D Clean Version ordered without sensors M A
GA aluminum
cannot be retrofitted with sensor capability.
Intermediate trunnion MT4
G 7
(requires XV dimension)
Trunnion flange at head (front) end 4 H P
Trunnion flange at cap (rear) end 4 J 8
Double Rod Cylinders None (MX0) N 9
Double rod option is available with Mounting
Styles MX0, MS1, MF1, MF2 and MT4.
For double rod cylinders, it is assumed that
the rod number and rod end are the same
for both piston rods. On a double rod cylinder
where the two rod ends are different, use
a rod end of ‘3’ and be sure to clearly state
which rod end is to be assembled at which
end.

C9 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Air Cylinders
General Specifications P1D Series
C086
Specifications P1D Rod Lock Version
• Bore sizes 32-200mm • Fluid Medium: Dry, filtered, compressed air
• Max stroke 2800mm • Maximum Cylinder Operating Pressure:
• Min stroke 25mm 10 Bar (145 PSI)
(must specify Tie Rod Version for strokes <25mm) • Required Pressure to Unlock1: 4 Bar (58 PSI)
• Rod Ends – 2 standard, specials to order • Minimum Torque Required for Manual Override Version:
• Single rod end and double rod end styles 32mm Bore = 0.9 N-m / 8 in-lbs
• Working pressure Max 10 Bar (145 PSI) 40mm Bore = 0.9 N-m / 8 in-lbs
• Working temperature min max 50mm Bore = 2.7 N-m / 24 in-lbs
63mm Bore = 2.7 N-m / 24 in-lbs
C
Standard -20°C (-4°F)   +80°C (+176°F)
High temp version -10°C (+14°F) +121°C (+250°F) 80mm Bore = 27.1 N-m / 240 in-lbs
100mm Bore = 36.6 N-m / 324 in-lbs
Aluminum piston is required for service above +80°C
(+176°F) 125mm Bore = 61.0 N-m / 540 in-lbs
• Greased for life (non-lube), does not normally need ad- • Maximum Operating Temperature:
ditional lubrication. If air line lubrication is initiated, it must -10°C to +75°C, +14°F to +167°F
always be continued. • Maximum Cylinder Operating Speed:
• Working medium Dry, filtered compressed air 5 feet per second
to ISO 8573-1 class 3. 4. 3. or better 1Signal pressure to port on locking device. Operation at pressures
lower than 4 Bar (58 psi) may lead to inadvertent engagement of the
P1D Clean Version rod lock device.
Min stroke 25mm
Protection class Hose-proof in accordance with IP65
Chemical resistance Tested for normally used industrial
detergents, both acid and alkaline
Quick Reference
Theoretical Cylinder Forces
Cylinder Piston Rod Cushioning Air at 6 Bar (N) 2
Bore Area, Dia. Area, Male Length Consumption 1 Connection
Size cm2 mm cm2 Thread mm litre Thread 4 Extend Stroke Retract Stroke
32 8.0 12 1.1 M10x1.25 17 0.105 G1/8 482 414
40 12.6 16 2.0 M12x1.25 19 0.162 G1/4 754 633
50 19.6 20 3.1 M16x1.5 20 0.253 G1/4 1178 989
63 31.2 20 3.1 M16x1.5 23 0.414 G3/8 1870 1681
80 50.3 25 4.9 M20x1.5 23 0.669 G3/8 3016 2721
100 78.5 25 4.9 M20x1.5 27 1.043 G1/2 4712 4417
125 122.7 32 8.0 M27x2 30 1.662 G1/2 7363 6880
160 201.1 40 12.6 M36x2 38 2.724 G3/4 12.064 11,310
200 314.2 40 12.6 M36x2 38 4.256 G3/4 18.850 18,096

Total Mass (kg) Total Mass (kg) Moving Components

Supplement per Supplement per
Cylinder 0mm Stroke 3 10mm Stroke at 0mm Stroke 10mm Stroke
Bore Size Standard Tie-Rod Clean Standard Tie-Rod Clean All Variants All Variants
32 0.55 0.54 0.60 0.023 0.022 0.047 0.13 0.009
40 0.80 0.79 0.88 0.033 0.030 0.063 0.24 0.016
50 1.20 1.20 1.32 0.048 0.048 0.094 0.42 0.025
63 1.73 1.73 1.86 0.051 0.051 0.101 0.50 0.025
80 2.45 2.47 2.63 0.075 0.079 0.142 0.90 0.039
100 4.00 4.00 4.22 0.084 0.084 0.168 1.10 0.039
125 6.87 6.73 7.01 0.138 0.129 0.248 2.34 0.063
160 — 16.19 — — 0.160 — Consult Factory Consult Factory
200 — 22.23 — — 0.185 — Consult Factory Consult Factory
1 Free air consumption per 10 mm stroke for a double stroke at 6 bar
2 The values for cylinder forces are theoretical and should be reduced to suit working conditions.
3 Total Mass for composite piston for 32-125mm bores and aluminum piston for 160-200mm bores.
4 ISO 1179-1 with ISO 228-1 threads

C10 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Air Cylinders
Material Specifications P1D Series
C086
Standard Version Additional/Substitute Specifications
Body extrusion Clear anodized aluminium P1D Clean Version
End covers Powder coated or black anodized Transparent molding Silicone
aluminum
Transparent cover ABS
End cover inserts POM
Screws, sensor system Stainless steel
End cover nuts/screws Zinc plated steel 8.8
Upper seal, cover EPDM
Piston rod nut Zinc plated steel
Lower seal, cover Rubber
Piston rod Chrome-plated steel (standard)
Sealing plugs PA
Rod wiperseal PUR
Piston rod nut Stainless steel
Piston rod bearing POM

C
Piston POM P1D Tie-Rod Version
Piston bearing POM Tie-rods Blackened steel
Magnetic ring Plastic bound magnetic material
Piston fastener Zinc plated steel P1D Removable Gland Version

P1D
(composite piston) End covers Black anodized aluminum
Piston seal PUR End cover screws Zinc plated steel 8.8
O-rings Nitrile rubber, NBR (32-125mm bores)
End-of-stroke bumpers Cylinder Body Clear anodized aluminum

P1A
and end seals PUR Rod gland PTFE filled high strength bronze
Cushioning seals PUR Rod seal Buna Nitrile for sealing action
Cushioning screws PA Rod wiper Buna Nitrile for wiping action
Piston rod Case hardened chrome-plated
Piston Rod Material Options steel
(or with equivalent properties): Piston rod nut Zinc plated steel
Standard Case-hardened, chrome Piston POM (standard)
plated carbon steel Aluminum (optional)
Chrome plated stainless steel 17-4 PH, chrome plated Piston seals PUR
stainless steel Piston bearing POM or Molyguard wear band for
Stainless steel 303 stainless steel aluminum piston
Acid-resistant stainless steel 316 stainless steel Magnetic ring Plastic bound magnetic material
Piston fastener Zinc plated steel
(composite piston)
O-rings Buna Nitrile
Cushioning seals PUR
Cushioning screws Stainless steel (brass for 160 and
200mm bores)
Design Variants for Removable Gland Version
High temperature option includes:
All seals Fluorocarbon
Piston Aluminum (without magnetic ring)
Low pressure hydraulic option includes:
Rod seal Buna Nitrile
Rod wiper PUR
Piston seals Buna Nitrile
Piston Aluminum (non-cushioned)
Metallic Rod Scraper includes:
Rod wiper Dual high strength bronze wipers
with nitrile or fluorocarbon
energizer

C11 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Air Cylinders
Technical Data P1D Series
C086
Cushioning Characteristics
The diagram below is used for sizing of cylinders related to the The load is the sum of internal and external friction, plus any
cushioning capacity. The maximum cushioning capacity shown gravitational forces. At high relative load (pressure drop
in the diagram assumes the following: exceeding 1 bar), we recommend that for any given speed, the
mass should be reduced by a factor of 2.5, or for a given mass,
• Low load, i.e. low pressure drop across the piston
the speed should be reduced by a factor of 1.5. This is in rela-
• Equilibrium speed tion to the maximum performance given in the diagram.
• Correctly adjusted cushioning screw
• 6 bar at cylinder port

C Speed [m/s]

4.0
3.0

2.0
1.5
Ø3 Ø4
2 0 Ø5 Ø6
1.0 0 3
Ø8 Ø1
0 00
Ø1
25
0.5
0.4
0.3

0.2

0.1
1 2 3 4 5 10 20 30 40 50 100 200 300 500 1000 2000
Mass [kg]

Recommended Air Quality for Cylinders ISO 8573-1 Quality Classes

For best possible service life and trouble-free operation, ISO Polution Water Oil
8573-1 quality class 3.4.3 should be used. This means 5
µm filter (standard filter) dew point +3°C (+37°F) for indoor Max Pressure Dew
Particle Max. Con- Max. Con-
operation (a lower dew point should be selected for outdoor Point
Quality Size centration centration
operation) and oil concentration 1.0 mg oil/m3, which is what a Class (mm) (mg/m3) (°C) (°F) (mg/m3)
standard compressor with a standard filter gives. 1 0.1 0.1 -70 -94 0.01
2 1 1 -40 -40 -0.1
3 5 5 -20 -4 1.0
4 15 8 +3 +37 5.0
5 40 10 +7 +44 25
6 – – +10 +50 –

C12 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Air Cylinders
Technical Data P1D Series
C086
Guide for Selecting Suitable Tubing
The selection of the correct size of tubing is often based The following prerequisites apply:
on experience, with no great thought to optimizing energy The cylinder load should be about 50% of the theoretical force
efficiency and cylinder velocity. This is usually acceptable, but (= normal load). A lower load gives a higher velocity and vice
making a rough calculation can result in worthwhile economic versa. The tube size is selected as a function of the cylinder
gains. bore, the desired cylinder velocity and the tube length between
the valve and the cylinder.
The following is the basic principle:
1. The primary line to the working valve could be over If you want to use the capacity of the valve to its maximum,
sized (this does not cause any extra air consumption and and obtain maximum speed, the tubing should be chosen so
consequently does not create any extra costs in operation). that they at least correspond with the equivalent restriction

C
2. The tubes between the valve and the cylinder should, diameter (see description below), so that the tubing does not
however, be optimized according to the principle that restrict the total flow. This means that a short tubing must
an insufficient bore throttles the flow and thus limits the have at least the equivalent restriction diameter. If the tubing is
cylinder speed, while an oversized pipe creates a dead longer, choose it from the table below. Straight fittings should
volume which increases the air consumption and filling be chosen­ for highest flow rates. (Elbow and banjo fittings

P1D
time. cause restriction.)
The chart below is intended to help when selecting the correct
size of tube to use between the valve and the cylinder.

P1A
Cylinder Equivalent throttling bore 1) Tube
Ø [mm] ØOut./ØInt.
[mm]

11 –/16

10 –/15

–/14
9
–/13

Suitable area for valve with Qn2) app 3000 l/min

8
–/12
7 14/11

Ø125 12/10
6

Suitable valve Qn2) app 1000 l/min

Suitable valve Qn2) app 800 l/min
Ø100 5
10/8
Ø80 4

Ø63 8/6
3
Ø50
Ø40 2 6/4
Ø32 5/3
Ø25
Ø20 1 4/2.7
Ø16
Ø10

0.2 0.5 0.8 1.1 1.4 0 1 2 3 4 5 6 7 8 9 10

Cylinder speed [m/s] Length of tubing [m]

1) The “equivalent throttling bore” is a long throttle (for example a tube)

or a series of throttles (for example, through a valve) converted to a
short throttle which gives a corresponding flow rate. This should not be
confused with the “orifice“ which is sometimes specified for valves. The
value for the orifice does not normally take account of the fact that the
valve contains a number of throttles.
2) Qn is a measure of the valve flow capacity, with flow measured in litre
per minute (l/min) at 6 bar(e) supply pressure and 1 bar pressure drop
across the valve.

C13 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Air Cylinders
Technical Data P1D Series
C086
P1D Rod Lock Version – Rod Lock Data Sample Pneumatic Circuit

Connection
The signal air for the locking device can be obtained directly
from a main air supply, or from the air supply serving the
valve that controls the cylinder itself. For controlled ON/OFF
operation of the locking device, a separate quick-venting valve
is used.
The piston rod should not be moving when the locking device
is activated. The locking device is not intended to brake a

C movement in repeated sequences.

3/2 LOCK VALVE 5/3 CYLINDER
Holding Forces (internal pilot) VALVE
(external pilot)
Holding Forces
Bore Size Auxiliary
(N) (lbs) Supply
32mm 550 123
Main Supply
40mm 860 193
50mm 1345 303 1. Lock valve must be maintained energized during cylinder
63mm 2140 481 motion, otherwise rod lock is engaged and cylinder valve
80mm 3450 755 shifts to mid position.
100mm 5390 1211 2. Cylinder valve must be maintained energized during
125mm 8425 1894 extend or retract. Also keep energized at end of stroke until
change of direction is desired.
NOTE: All P1D Rod Lock Versions are not intended for use in 3. Mid position of 5/3 Cylinder valve may be pressurized
water service applications, or in environments that have high outlets if the combination of pressure load on the cylinder
humidity levels and/or splashing fluids present. and inertia effects of the attached load do not exceed
the holding force rating of the rod lock device, including
allowance for wear.
4. Do not use cylinder lines for any logic functions —
pressure levels vary too much.

Use as a Brake Speed [m/s]

The chart to the right shows the maximum values for speed
and braking mass if the cylinder is used as a brake. The cylin- 2.0
der should not be exposed to additional compressive forces as 1.5
this significantly reduces the external mass that can be braked. 1.0
We recommend systems in which the cylinder does not act as Ø3
2 Ø40 Ø50 Ø6 Ø8 Ø1 Ø
00 125
a motor during braking. Heat is generated if the brake is used 0.5
3 0
frequently, and this must be taken into account to ensure that 0.4
the maximum temperature is not exceeded. 0.3

0.2

0.1
0.5 1 2 3 5 10 20 30 50 100 200
Mass [Kg]

C14 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Air Cylinders
Dimensions P1D Series
C086
P1D Standard Version BG

PP
L12 EE RT
AM PL

OA
SS
ØBA
ØD
ØB

KK

TT
ØD4
DIN 439B

C
SW VD VA R
L2 G G
E
WH L8 + S

P1D
L9 + 2 x S
WH WH + S

P1A
S=Stroke

Dimensions
EE
Cylinder AM B BA BG D D4 NPTF/ G L2 L8 L9 L12
E BSPP1 KK
Bore mm mm mm mm mm mm BSPT mm mm mm mm mm
32 22 30 30 16 12 45.0 50.0 G1/8 1/8 28.5 M10x1.25 16.0 94 146 6.0
40 24 35 35 16 16 52.0 57.4 G1/4 1/4 33.0 M12x1.25 19.0 105 165 6.5
50 32 40 40 16 20 60.7 69.4 G1/4 1/4 33.5 M16x1.5 24.0 106 180 8.0
63 32 45 45 16 20 71.5 82.4 G3/8 3/8 39.5 M16x1.5 24.0 121 195 8.0
80 40 45 45 17 25 86.7 99.4 G3/8 3/8 39.5 M20x1.5 30.0 128 220 10.0
100 40 55 55 17 25 106.7 116.0 G1/2 1/2 44.5 M20x1.5 32.4 138 240 10.0
125 54 60 60 20 32 134.0 139.0 G1/2 1/2 51.0 M27x2 45.0 160 290 13.0

Cylinder OA PL PP R SS SW TT VA VD WH
RT
Bore mm mm mm mm mm mm mm mm mm mm
32 6 13 21.8 32.5 M6 4.0 10 4.5 3.5 4.5 26
40 6 14 21.9 38.0 M6 8.0 13 5.5 3.5 4.5 30
50 8 14 25.9 46.5 M8 4.0 17 7.5 3.5 4.5 37
63 8 16 27.4 56.5 M8 6.5 17 11.0 3.5 4.5 37
80 6 16 30.5 72.0 M10 0 22 15.0 3.5 4.5 46
100 6 18 35.8 89.0 M10 0 22 20.0 3.5 4.5 51
125 8 23 40.5 110.0 M12 0 27 17.5 3.5 6.5 65
1 ISO 1179-1 with ISO 228-1 threads

Tolerances
Cylinder BA L8 L9 R
B Stroke tolerance
Bore mm mm mm mm
32 d11 d11 ±0.4 ±2 ±0.5 +1/-0
40 d11 d11 ±0.7 ±2 ±0.5 +1/-0
50 d11 d11 ±0.7 ±2 ±0.6 +1/-0
63 d11 d11 ±0.8 ±2 ±0.7 +1/-0
80 d11 d11 ±0.8 ±3 ±0.7 +1/-0
100 d11 d11 ±1.0 ±3 ±0.7 +1/-0
125 d11 d11 ±1.0 ±3 ±1.1 +1/-0

C15 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Air Cylinders
Dimensions P1D Series
C086
P1D Removable Gland Version

BG PP RT

EE
PL
AM L 12 OA
ØD KK SS

ØB ØBA

TT

C DIN 439B VD VA
R
ØD 4
SW L2 G G E

WH L8 + S

L9+ 2 x S

WH WH + S

S=Stroke
Dimensions
EE
Cylinder AM B BA BG D D4 E NPTF/ G L2 L8 L9 L12
BSPP 1 KK
bore mm mm mm mm mm mm mm BSPT mm mm mm mm mm
32 22 30 30 16 12 45.0 46.5 G1/8 1/8 28.5 M10x1.25 18 94 146 6.0
40 24 35 35 16 16 52.0 52.0 G1/4 1/4 33.0 M12x1.25 20 105 165 6.5
50 32 40 40 16 20 60.7 63.5 G1/4 1/4 33.5 M16x1.5 26 106 180 6.5
63 32 45 45 16 20 71.5 76.0 G3/8 3/8 39.5 M16x1.5 26 121 195 6.5
80 40 45 45 17 25 86.7 95.5 G3/8 3/8 39.5 M20x1.5 33 128 220 10.0
100 40 55 55 17 25 106.7 114.5 G1/2 1/2 44.5 M20x1.5 33 138 240 10.0
125 54 60 60 20 32 134.0 140.0 G1/2 1/2 51.0 M27x2 41 160 290 13.0

Cylinder OA PL PP R SS SW TT VA VD WH
RT
bore mm mm mm mm mm mm mm mm mm mm
32 6 13 21.8 32.5 M6 6.5 10 4.5 3.5 4.5 26
40 6 14 21.9 38.0 M6 8.0 13 5.5 3.5 4.5 30
50 8 14 25.9 46.5 M8 4.0 17 7.5 3.5 4.5 37
63 8 16 27.4 56.5 M8 6.5 17 11.0 3.5 4.5 37
80 6 16 30.5 72.0 M10 0 22 15.0 3.5 4.5 46
100 6 18 35.8 89.0 M10 0 22 20.0 3.5 4.5 51
125 8 23 40.5 110.0 M12 0 27 17.5 5.5 6.5 65
1 ISO 1179-1 with ISO 228-1 threads

Tolerances
Cylinder BA L8 L9 R
B Stroke tolerance
Bore mm mm mm mm
32 d11 d11 ±0.4 ±2 ±0.5 +1/-0
40 d11 d11 ±0.7 ±2 ±0.5 +1/-0
50 d11 d11 ±0.7 ±2 ±0.6 +1/-0
63 d11 d11 ±0.8 ±2 ±0.7 +1/-0
80 d11 d11 ±0.8 ±3 ±0.7 +1/-0
100 d11 d11 ±1.0 ±3 ±0.7 +1/-0
125 d11 d11 ±1.0 ±3 ±1.1 +1/-0

C16 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 (Revised 03-05-09) Air Cylinders
Dimensions P1D Series
C086
P1D Rod Lock Version
(Version R or L)

BG

EE PP
AM L 12 G1/8 PL RT 6
T
KK SS

ØB ØBA OA
C
ØD TT

P1D
A S ØD4 G VA R
DIN 439B
SW VD L E
P
(M5 Ø32 - Ø40)

P1A
WH H
G 1/8 Ø50 - Ø125)
L 8 + Stroke

Dimensions
Cylinder A AM B BA BG D D4 E G H L L8 L12
EE 1 KK
Bore mm mm mm mm mm mm mm mm mm mm mm mm mm
32 16 22 30 30 16 12 45.0 46.5 G1/8 28.5 71.5 M10x1.25 56.0 137 6.0
40 16 24 35 35 16 16 52.0 52.0 G1/4 33.0 77.0 M12x1.25 56.0 149 6.5
50 18 32 40 40 16 20 60.7 63.5 G1/4 33.5 80.5 M16x1.5 62.5 153 6.5
63 26 32 45 45 16 20 71.5 76.0 G3/8 39.5 96.5 M16x1.5 74.5 178 6.5
80 35 40 45 45 17 25 86.7 95.5 G3/8 39.5 110.5 M20x1.5 87.0 199 10.0
100 50 40 55 55 17 25 106.7 114.5 G1/2 44.5 132.5 M20x1.5 106.0 226 10.0
125 60 54 60 60 20 32 134.0 140.0 G1/2 51.0 145.0 M27x2 117.0 254 13.0

Cylinder OA P PL PP R RT S SS SW T TT VA VD WH
Bore mm mm mm mm mm mm mm mm mm mm mm mm mm mm
32 6 64.8 13 21.8 32.5 M6 7 6.5 10 2.5 4.5 3.5 4.5 15
40 6 68.0 14 21.9 38.0 M6 9 8.0 13 2.0 5.5 3.5 4.5 16
50 8 73.5 14 25.9 46.5 M8 8 4.0 17 4.0 7.5 3.5 5.0 17
63 8 89.5 16 27.4 56.5 M8 8 6.5 17 2.0 11.0 3.5 5.0 17
80 6 101.5 16 30.5 72.0 M10 9 0 22 5.0 15.0 3.5 4.0 20
100 6 123.5 18 35.8 89.0 M10 12 0 22 6.0 20.0 3.5 4.0 20
125 8 136.0 23 40.5 110.0 M12 12 0 27 6.0 17.5 5.5 6.0 27
1 ISO 1179-1 with ISO 228-1 threads

Tolerances
Cylinder B R L8 BA Stroke-length Tolerance
Bore mm mm mm mm mm
32 d11 ±0.5 ±0.4 d11 +1/-0
40 d11 ±0.5 ±0.7 d11 +1/-0
50 d11 ±0.6 ±0.7 d11 +1/-0
63 d11 ±0.7 ±0.8 d11 +1/-0
80 d11 ±0.7 ±0.8 d11 +1/-0
100 d11 ±0.7 ±1.0 d11 +1/-0
125 d11 ±1.1 ±1.0 d11 +1/-0

C17 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 (Revised 03-05-09) Air Cylinders
Dimensions Rod Lock Version P1D Series
C086
P1D Rod Lock Version with Manual Override
(Version J)

MOUNTING SURFACE
MR 1
L12 EE
BG PP
OA NR N HEX PL
AM
T
MR 2 KK SS

C RT ØB ØBA

ØD TT
R DIN 439B A S ØD 4 G VA
L
E 6 SW
VD P (M5 Ø32 & Ø40)
(G1/8" Ø50-Ø125)
H
(M5 Ø32 & Ø40)
WH L 8 + Stroke
(G1/8" Ø50-Ø125)

Dimensions
Cylinder A AM B BA BG D D4 E G H L L8 L12 MR1 MR2
EE 1 KK
Bore mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
32 27.0 22 30 30 16 12 45.0 46.5 G1/8 28.5 71.5 M10X1.25 56.0 137 6.0 16.0 3.0
40 27.0 24 35 35 16 16 52.0 52.0 G1/4 33.0 77.0 M12X1.25 56.0 149 6.5 16.0 3.0
50 21.5 32 40 40 16 20 60.7 63.5 G1/4 33.5 80.5 M16X1.5 62.5 153 6.5 18.5 5.5
63 39.0 32 45 45 16 20 71.5 76.0 G3/8 39.5 96.5 M16X1.5 74.5 178 6.5 22.0 4.0
80 38.5 40 45 45 17 25 86.7 95.5 G3/8 39.5 110.5 M20X1.5 87.0 199 10.0 15.0 19. 8
100 55.0 40 55 55 17 25 106.7 114.5 G1/2 44.5 132.5 M20X1.5 106.0 226 10.0 15.0 20.8
125 61.0 54 60 60 20 32 134.0 140.0 G1/2 51.0 145.0 M27X2 117.0 254 13.0 19.0 23.0

Cylinder N NR OA P PL PP R S SS SW T TT VA VD WH
RT
Bore mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
32 8 10.0 6 64.8 13 21.8 32.5 M6 7 6.5 10 2.5 4.5 3.5 4.5 15
40 8 10.0 6 68.0 14 21.9 38.0 M6 9 8.0 13 2.0 5.5 3.5 4.5 16
50 10 12.0 8 73.5 14 25.9 46.5 M8 8 4.0 17 4.0 7.5 3.5 5.0 17
63 10 12.0 8 89.5 16 27.4 56.5 M8 8 6.5 17 2.0 11.0 3.5 5.0 17
80 11 12.5 6 101.5 16 30.5 72.0 M10 9 0 22 5.0 15.0 3.5 14.0 30
100 11 12.5 6 123.5 18 35.8 89.0 M10 12 0 22 6.0 20.0 3.5 14.0 30
125 11 12.5 8 136.0 23 40.5 110.0 M12 12 0 27 6.0 17.5 5.5 16.0 37
1 ISO 1179-1 with ISO 228-1 threads

Tolerances
Cylinder B R L8 BA Stroke-length Tolerance
Bore mm mm mm mm mm
32 d11 ±0.5 ±0.4 d11 +1/-0
40 d11 ±0.5 ±0.7 d11 +1/-0
50 d11 ±0.6 ±0.7 d11 +1/-0
63 d11 ±0.7 ±0.8 d11 +1/-0
80 d11 ±0.7 ±0.8 d11 +1/-0
100 d11 ±0.7 ±1.0 d11 +1/-0
125 d11 ±1.1 ±1.0 d11 +1/-0

C18 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Air Cylinders
Dimensions P1D Series
C086
P1D Tie-Rod Version (32-125mm)

PP
L12 EE RT
AM PL

OA
ØD6

SS
ØBA
ØD
ØB

KK

TT
ØD5
DIN 439B
SW VD
L2
VA R
C
G G
E
WH L8 + S

P1D
P1D Clean Version

P1A
PP
L12 EE RT E 2 max
AM PL

OA
SS
ØBA
ØD
ØB

KK

TT
ØD7

E1
DIN 439B
SW VD VA
L2 R
G G
L8 + S E
WH

Dimensions
Cylinder D5 D6 D7 E1 E2 max
Bore mm mm mm mm mm
32 36 5.3 49.6 32 5
40 45 5.3 57.3 36 6
50 55 7.1 69.3 42 6
63 68 7.1 82.3 49 5
80 85 8.9 99.3 57 5
100 105 8.9 117.6 68 6
125 132 10.7 142.8 81 6
Other dimensions, see page C15.

C19 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Air Cylinders
Dimensions P1D Series
C086
P1D Tie-Rod Version (160-200mm)
Y PJ + STROKE
WH
E VD

E TG B MM B

C
VE BG EE G VD
DD
TG
G
ZJ + STROKE

ZM + (2 x STROKE)
Y PJ + STROKE
WH WH + STROKE

MM MM

AM AM

VE G EE G VE
ZJ + STROKE

Rod End #1 Rod End #2

Dimensions
EE
B
Cylinder AM BG DD E NPTF/ G MM TG VD VE WH Y PJ 1 ZJ 1 ZM 2
d11 BSPP 3
Bore mm mm mm BSPT mm mm mm mm mm mm mm mm mm mm
mm
160 72 65 24 M16 177 G3/4 3/4 54 40 140 6 56 80 105 130 260 340
200 72 75 24 M16 214 G3/4 3/4 54 40 175 6 56 95 120 130 275 370
1 Add stroke
2 Add 2× stroke
3 ISO 1179-1 with ISO 228-1 threads

Double Rod Cylinders

Double rod option is available on Mounting Styles MX0, MS1,
MF1, MF2 and MT4.
For double rod cylinders, it is assumed that the rod number
and rod end are the same for both piston rods. On a double
rod cylinder where the two rod ends are different, use a
rod end of ‘3’ and be sure to clearly state which rod end is
to be assembled at which end.

C20 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 (Revised 03-05-09) Air Cylinders
P1D Rod End Dimensions P1D Series
C086
All Mountings Except MF1
Thread Style N Thread Style 6
“Special Thread”
SW
WRENCH
WH SW WH Style 3
WRENCH
FLATS VD FLATS VD Special thread, extension,
AM
rod eye, blank, etc
are also available. To
order, specify “Style 3”
BC NA KK D B BC NA KF D B and provide desired
dimensions for KF or
KK, AM and WH. If
otherwise special, furnish
C
L12 L12
dimensioned sketch.
AM L2 L2

B SW

P1D
Bore D KK KF AM BC L12 NA VD L2 WH*
d11 across flats
32 12 M10x1.25 M8x1 22 30 27 10 6 11 4.5 18 26
40 16 M12x1.25 M10x1.25 24 35 32 13 6.5 15 4.5 20 30

P1A
50 20 M16x1.5 M14x1.5 32 40 36 17 6.5 19 4.5 26 37
63 20 M16x1.5 M14x1.5 32 45 36 17 6.5 19 4.5 26 37
80 25 M20x1.5 M18x1.5 40 45 41 22 10 24 4.5 33 46
100 25 M20x1.5 M18x1.5 40 55 41 22 10 24 4.5 33 51
125 32 M27x2 M24x2 54 60 50 27 13 31 6.5 41 65
160 40 M36x2 M30x2 72 65 60 36 16 39 6 56 80
200 40 M36x2 M30x2 72 75 60 36 16 39 6 56 95
*NOTE: Dimensions do not apply to Rod Lock Versions.

With MF1 Mounting

Thread Style N Thread Style 6
“Special Thread”
W MF W MF Style 3
SW SW Special thread, extension,
WRENCH WRENCH rod eye, blank, etc
FLATS FLATS AM
are also available. To
order, specify “Style 3”
and provide desired
NA KK D NA KF D dimensions for KF or
KK, AM and WH. If
otherwise special, furnish
dimensioned sketch.
L12 L12

AM

L2 L2
WH WH

SW
Bore D KK KF AM L12 MF NA L2 W† WH†
across flats
32 12 M10x1.25 M8x1 22 10 6 10 11 18 16 26
40 16 M12x1.25 M10x1.25 24 13 6.5 10 15 20 20 30
50 20 M16x1.5 M14x1.5 32 17 6.5 12 19 26 25 37
63 20 M16x1.5 M14x1.5 32 17 6.5 12 19 26 25 37
80 25 M20x1.5 M18x1.5 40 22 10 16 24 33 30 46
100 25 M20x1.5 M18x1.5 40 22 10 16 24 33 35 51
125 32 M27x2 M24x2 54 27 13 20 31 41 45 65
160 40 M36x2 M30x2 72 36 16 20 39 56 60 80
200 40 M36x2 M30x2 72 36 16 25 39 56 70 95
†NOTE: Dimensions do not apply to Rod Lock Versions.

C21 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 (Revised 03-23-09) Air Cylinders
Duplex & Tandem Cylinders P1D Series
C086
3 and 4-Position Duplex Cylinders
This type of cylinder function can consist of two cylinders
installed back to back. Two cylinders with the same stroke
result in a 3-position cylinder with a symmetrical center
position, whereas two different strokes result in a 4-position
cylinder where the two central positions can be calculated
from the different stroke lengths.

A 3-position duplex cylinder can also be obtained by

mounting two cylinders of different strokes, in series, but
not connecting the piston rods together. This concept is

C illustrated in a guided cylinder application shown on page

F162 of the HB series.

These 3 and 4-position cylinders can be ordered in two ways

as follows.

Factory-fitted P1D Duplex Cylinders

P1D tie-rod version duplex cylinders are completed at the
factory and are joined together as one unit by special tie-
rods. This version needs to be ordered as a special ( / ).
Please consult factory for assistance.

Customer-Installed Mounting Kit

There is an installation mounting kit available for cylinder
bores 32-100mm which makes it possible to join any two P1D
cylinders, of the same bore, together at any time to make a 3
or 4-position cylinder. Please refer to the cylinder mountings
on top of page C28.

Tandem Cylinders
In addition to the duplex cylinder options above, the P1D
tie-rod version is also available as a tandem cylinder. By
ordering two cylinders of equal strokes, mounted in series,
and connecting the piston rods together, you achieve almost
twice the output force, at the same pressure, as a standard
cylinder. This is a great advantage when restricted mounting
space prevents the use of a larger bore cylinder. Please
review version and function options in the model code on
page C8.

Cylinder A (mm)
Bore P1D-T P1D-S
32 247 256
40 277 286
50 293 306
63 323 336
80 355 373
100 385 403
125 461 –
S=Stroke

3 position: A + 2 x S
4 position: A + S1 + S2

C22 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 (Revised 03-05-09) Air Cylinders
Cylinder Mountings P1D Series
C086
Flange MF1 R

Flange MF2

ØFB
Intended for fixed mounting of cylinder. Flange can be

Ød1
UF

TF
fitted to front or rear end cover of cylinder.
Materials
32-100mm bore flange: Surface-treated aluminum, black TG1
E
125-200mm bore flange: Steel, black MF MF
Mounting screws acc. to DIN 6912: Zinc-plated steel 8.8
Supplied complete with mounting screws for attachment
to cylinder.

I1
W
C
According to ISO MF1/MF2, VDMA 24 562, AFNOR ZB+S
ZF+S

P1D
d1 FB R MF TF I1
Bore TG1 E W ZF ZB Weight
H11 H13 JS14 JS14 JS14 UF -0.5 Part Number
mm mm mm mm mm mm kg
mm mm mm mm mm mm
32 30 7 32.5 45 32 10 64 80 5.0 16 130 123.5 0.23 P1C-4KMBA

P1A
40 35 9 38.0 52 36 10 72 90 5.0 20 145 138.5 0.28 P1C-4LMBA
50 40 9 46.5 65 45 12 90 110 6.5 25 155 146.5 0.53 P1C-4MMBA
63 45 9 56.5 75 50 12 100 120 6.5 25 170 161.5 0.71 P1C-4NMBA
80 45 12 72.0 95 63 16 126 150 8.0 30 190 177.5 1.59 P1C-4PMBA
100 55 14 89.0 112 75 16 150 185 8.0 35 205 192.5 2.19 P1C-4QMBA
125 60 16 110.0 140 90 20 180 220 10.5 45 245 230.5 3.78 P1C-4RMB
160 65 18 140.0 190 115 20 230 279 7.0 60 280 266 C.F. L075370160
200 75 22 175.0 228 135 25 270 318 13.0 70 300 281 C.F. L075370200
S = Stroke length C.F. = Consult Factory

Foot Bracket MS1

Intended for fixed mounting of cylinder. Foot bracket
AH

can be fitted to front and rear end covers of cylinder.

I7
I9
Materials
AT

TR
Foot bracket: Surface-treated steel, black TGI

Mounting screws acc. to DIN 912: Zinc-plated steel 8.8 E

Supplied in pairs with mounting screws for attachment

to cylinder­.
ØAB

AU AO
SA+S
According to ISO MS1, VDMA 24 562, AFNOR

AB TR AH I9
Bore TG1 E AO AU I7 AT SA Weight*
H14 JS14 JS15 JS14 Part Number
mm mm mm mm mm mm mm mm kg
mm mm mm mm
32 7 32.5 45 32 10 24 32 30 4.5 17.0 142 0.06 P1C-4KMF
40 9 38.0 52 36 8 28 36 30 4.5 18.5 161 0.08 P1C-4LMF
50 9 46.5 65 45 13 32 45 36 5.5 25.0 170 0.16 P1C-4MMF
63 9 56.5 75 50 13 32 50 35 5.5 27.5 185 0.25 P1C-4NMF
80 12 72.0 95 63 14 41 63 49 6.5 40.5 210 0.50 P1C-4PMF
100 14 89.0 115 75 15 41 71 54 6.5 43.5 220 0.85 P1C-4QMF
125 16 110.0 140 90 22 45 90 71 8.0 60.0 250 1.48 P1C-4RMF
160 18 140.0 177 115 24 60 115 63.5 4.75 63.5 300 C.F. L075380160
200 22 175.0 214 135 30 70 135 65 8.0 65.0 320 C.F. L075380200
S = Stroke length C.F. = Consult Factory *Weight per item

C23 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Air Cylinders
Cylinder Mountings P1D Series
C086
Pivot Bracket with Rigid Bearing
Intended for flexible mounting of cylinder. The pivot EM

ØCK
R1 G1
bracket can be combined with clevis bracket MP2.
Materials
Pivot bracket: Surface-treated aluminium, black

CA
Ø S5
Bearing: Sintered oil-bronze bushing

H6
K1 G2
K2 G3

According to CETOP RP 107 P, VDMA 24 562, AFNOR

C Bore
mm
CK
H9
mm
S5
H13
mm
K1
JS14
mm
K2
G1
JS14
mm
G2
JS14
mm
EM
mm
G3
mm
CA
JS15
mm
H6
mm
R1
mm
Weight
kg
Part Number

32 10 6.6 38 51 21 18 25.5 31 32 8 10.0 0.06 P1C-4KMD

40 12 6.6 41 54 24 22 27.0 35 36 10 11.0 0.08 P1C-4LMD
50 12 9.0 50 65 33 30 31.0 45 45 12 13.0 0.15 P1C-4MMD
63 16 9.0 52 67 37 35 39.0 50 50 12 15.0 0.20 P1C-4NMD
80 16 11.0 66 86 47 40 49.0 60 63 14 15.0 0.33 P1C-4PMD
100 20 11.0 76 96 55 50 59.0 70 71 15 19.0 0.49 P1C-4QMD
125 25 14.0 94 124 70 60 69.0 90 90 20 22.5 1.02 P1C-4RMD
160 30 14.0 118 156 97 89 88.5 126 115 25 31.0 C.F. L075480160
200 30 16.0 122 162 105 89 88.5 130 135 30 31.0 C.F. L075480200
C.F. = Consult Factory

Swivel Eye Bracket (MP6) B2

B1
Intended for use together with clevis bracket GA

Z
Material
Bracket: Surface-treated aluminium, black
Z
(Cast iron for 160-200mm bores) EN

Swivel bearing acc. to DIN 648K: Hardened steel FL

I2
E

ØCN
Supplied complete with mounting screws
for attachment to cylinder.
R1
R2

According to VDMA 24 562, AFNOR XD+S

CN
Bore E B1 B2 EN R1 R2 FL I2 L XD Weight
H7 Z Part Number
mm mm mm mm mm mm mm mm mm mm mm kg
mm
32 45 10.5 – 14 16 – 22 5.5 12 10 142 4° 0.08 P1C-4KMSA
40 52 12.0 – 16 18 – 25 5.5 15 12 160 4° 0.11 P1C-4LMSA
50 65 15.0 51 21 21 19 27 6.5 15 16 170 4° 0.20 P1C-4MMSA
63 75 15.0 – 21 23 – 32 6.5 20 16 190 4° 0.27 P1C-4NMSA
80 95 18.0 – 25 29 – 36 10.0 20 20 210 4° 0.52 P1C-4PMSA
100 115 18.0 – 25 31 – 41 10.0 25 20 230 4° 0.72 P1C-4QMSA
125 140 25.0 – 37 40 – 50 10.0 30 30 275 4° 1.53 P1C-4RMSA
160 177 30.0 – 43 44 41 55 4.0 41 35 315 16° C.F. L075420160
200 214 30.0 – 43 48 42 60 8.0 42 35 335 16° C.F. L075420200
S = Stroke length C.F. = Consult Factory

C24 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Air Cylinders
Cylinder Mountings P1D Series
C086
Clevis bracket MP2
C
Intended for flexible mounting of cylinder. Clevis bracket UB

MP2 can be combined with clevis bracket MP4. CB

Materials
Clevis bracket: Surface-treated aluminium, black for
32-160mm bores; Cast iron for 200mm bore E
Pin: Surface hardened steel
Circlips according to DIN 471: Spring steel L
Mounting screws acc. to DIN 912: Zinc-plated steel 8.8 CD
MR

C
Now in aluminum! Supplied complete with mounting screws for attachment
to cylinder­.
I2
FL

According to ISO MP2, VDMA 24 562, AFNOR XD+S

P1D
UB CB FL CD
Bore C E L I2 MR XD Weight
h14 H14 ±0.2 H9 Part Number
mm mm mm mm mm mm mm kg
mm mm mm mm

P1A
32 53 45 45 26 22 13 5.5 10 10 142 0.08 P1C-4KMT
40 60 52 52 28 25 16 5.5 12 12 160 0.11 P1C-4LMT
50 68 65 60 32 27 16 6.5 12 12 170 0.14 P1C-4MMT
63 78 75 70 40 32 21 6.5 16 16 190 0.29 P1C-4NMT
80 98 95 90 50 36 22 10.0 16 16 210 0.36 P1C-4PMT
100 118 115 110 60 41 27 10.0 20 20 230 0.64 P1C-4QMT
125 139 140 130 70 50 30 10.0 25 25 275 1.17 P1C-4RMT
160 178 177 170 90 55 36 10.0 30 30 315 C.F. L075390160
200 178 214 170 90 60 41 18.0 30 30 335 C.F. L075390200
S = Stroke length C.F. = Consult Factory

Clevis Bracket MP4 EW

Intended for flexible mounting of cylinder. Clevis bracket MP4
can be combined with clevis bracket MP2.

Materials
Clevis bracket: Surface-treated aluminium, black for E
L
32-125mm bores; Cast iron for 160-200mm bores CD
Mounting screws acc. to DIN 912: Zinc-plated steel 8.8 MR

Supplied complete with mounting screws for attachment

to cylinder­. I2
FL
XD+S
According to ISO MP4, VDMA 24 562, AFNOR

L MR
Bore E EW FL I2 CD XD Weight
±0.2 H9 Part Number
mm mm mm mm mm mm mm kg
mm mm
32 45 26 22 13 5.5 10 10 142 0.09 P1C-4KME
40 52 28 25 16 5.5 12 12 160 0.13 P1C-4LME
50 65 32 27 16 6.5 12 12 170 0.17 P1C-4MME
63 75 40 32 21 6.5 16 16 190 0.36 P1C-4NME
80 95 50 36 22 10.0 16 16 210 0.46 P1C-4PME
100 115 60 41 27 10.0 20 20 230 0.83 P1C-4QME
125 140 70 50 30 10.0 25 25 275 1.53 P1C-4RME
160 177 90 55 36 13.5 30 30 315 C.F. L075410160
200 214 90 60 41 18.0 30 30 335 C.F. L075410200
S = Stroke length C.F. = Consult Factory

C25 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Air Cylinders
Cylinder Mountings P1D Series
C086
Clevis Bracket GA
Intended for flexible mounting of cylinder. Clevis bracket C
GA can be combined with pivot bracket with swivel bearing, B2

swivel eye bracket and swivel rod eye. B1

Materials

B3
Clevis bracket: Surface-treated aluminium
Pin: Surface hardened steel FL
L2 T
L1
Locking pin: Spring steel CN
E

Now in aluminium! Circlips according to DIN 471: Spring steel

Mounting screws acc. to DIN 912: Zinc-plated steel 8.8 R1

Supplied complete with mounting screws for attachment

C

R2
to cylinder­. L

XD+S

According to VDMA 24 562, AFNOR

B2 B1 FL CN
Bore C E T B3 R2 L1 I2 L R1 XD Weight
d12 H14 ±0.2 F7 Part Number
mm mm mm mm mm mm mm mm mm mm mm kg
mm mm mm mm
32 41 45 34 14 3 3.3 17 11.5 22 5.5 12 10 11 142 0.09 P1C-4KMCA
40 48 52 40 16 4 4.3 20 12.0 25 5.5 15 12 13 160 0.13 P1C-4LMCA
50 54 65 45 21 4 4.3 22 14.0 27 6.5 17 16 18 170 0.17 P1C-4MMCA
63 60 75 51 21 4 4.3 25 14.0 32 6.5 20 16 18 190 0.36 P1C-4NMCA
80 75 95 65 25 4 4.3 30 16.0 36 10.0 20 20 22 210 0.58 P1C-4PMCA
100 85 115 75 25 4 4.3 32 16.0 41 10.0 25 20 22 230 0.89 P1C-4QMCA
125 110 140 97 37 6 6.3 42 24.0 50 10.0 30 30 30 275 1.75 P1C-4RMCA
160 140 178 122 43 6 6.3 46 26.5 55 10.0 37 35 h9 36 C.F. C.F. L075510160
200 175 218 122 43 6 6.3 49 26.5 60 11.5 40 35 h9 38 C.F. C.F. L075510200
S = Stroke length C.F. = Consult Factory

Stainless Steel Pin Set GA Bore mm Weight kg Part Number

Materials 32 0.05 9301054311
Pin: Stainless steel 40 0.06 9301054312
Locking pin: Stainless steel
Circlips according to DIN 471: Stainless steel 50 0.07 9301054313
63 0.07 9301054314
80 0.17 9301054315
100 0.31 9301054316
125 0.54 9301054317

C26 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 (Revised 03-05-09) Air Cylinders
Cylinder Mountings P1D Series
C086
Head Detachable Clevis MP7
E
Intended for flexible mounting of cylinder
Materials
Clevis bracket: Cast iron for 32-63mm bores; E

Surface treated aluminum, black for 80-200mm bores

Mounting screws acc. to DIN 912: Zinc-plated steel 8.8
FW
Supplied complete with mounting screws for attachment UB

to cylinder­. XW
MR

CD
C
L
FL

P1D
According to ISO MP7, VDMA 24 562, AFNOR

CD E FL FW L MR UB XW
Bore Part Number

P1A
mm mm mm mm mm mm mm mm
32 10 46.5 22 8 12 10 45 4 L075400032
40 12 52 25 9 15 12 52 5 L075400040
50 12 63.5 27 10 15 13 60 10 L075400050
63 16 76 32 15 20 16 70 5 L075400063
80 16 95.5 36 20 20 17 90 10 L075400080
100 20 114.5 41 25 25 21 110 10 L075400100
125 25 140 50 30 35 25 130 15 L075400125
160 30 177 55 40 36 30 170 25 L075400160
200 30 214 60 40 41 30 170 35 L075400200

Pivot Bracket with Swivel Bearing

EN
Intended for use together with clevis bracket GA. EU ER G1

ØCN
Z

Material CH
Z

Ø S5
Pivot bracket: Surface-treated steel, black
H6

Swivel bearing acc. to DIN 648K: Hardened steel K1 G2

K2 G3

According to VDMA 24 562, AFNOR

CN S5 K1 G1 G2 CH
Bore K2 EU EN G3 H6 ER Weight
H7 H13 JS14 JS14 JS14 JS15 Z Part Number
mm mm mm mm mm mm mm kg
mm mm mm mm mm mm
32 10 6.6 38 51 10.5 21 18 14 31 32 10 16 4° 0.18 P1C-4KMA
40 12 6.6 41 54 12.0 24 22 16 35 36 10 18 4° 0.25 P1C-4LMA
50 16 9.0 50 65 15.0 33 30 21 45 45 12 21 4° 0.47 P1C-4MMA
63 16 9.0 52 67 15.0 37 35 21 50 50 12 23 4° 0.57 P1C-4NMA
80 20 11.0 66 86 18.0 47 40 25 60 63 14 28 4° 1.05 P1C-4PMA
100 20 11.0 76 96 18.0 55 50 25 70 71 15 30 4° 1.42 P1C-4QMA
125 30 14.0 94 124 25.0 70 60 37 90 90 20 40 4° 3.10 P1C-4RMA

C27 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 (Revised 03-05-09) Air Cylinders
Cylinder Mountings P1D Series
C086
Mounting Kit A
MF

Mounting kit for back to back mounted cylinders,

3 and 4 position duplex cylinders.

Material E
Mounting: Aluminium TG
Mounting screws: Zinc-plated steel 8.8

TG
E
ØBA
ØFB

C Bore
mm
E
mm
TG
mm
ØFB
mm
MF
mm
A
mm
ØBA
mm
Weight
kg
Part Number

32 50 32.5 6.5 5 16 30 0.060 P1E-6KB0

40 60 38.0 6.5 5 16 35 0.078 P1E-6LB0
50 66 46.5 8.5 6 20 40 0.162 P1E-6MB0
63 80 56.5 8.5 6 20 45 0.194 P1E-6NB0
80 100 72.0 10.5 8 25 45 0.450 P1E-6PB0
100 118 89.0 10.5 8 25 55 0.672 P1E-6QB0

Pivot Bracket for MT4

Intended for use together with central trunnion MT4.

Material B2 Ød1
Pivot bracket: Surface-treated aluminium fx45°

H1
Bearing acc. to DIN 1850 C: Sintered oil-bronze bushing

H2
C A
Ød2
Supplied in pairs. B1

According to ISO, VDMA 24 562, AFNOR

d2 fx45°
Bore B1 B2 A C d1 H1 H2 Weight*
H13 min Part Number
mm mm mm mm mm mm mm mm kg
mm mm
32 46 18.0 32 10.5 12 6.6 30 15 1.0 0.04 9301054261
40 55 21.0 36 12.0 16 9.0 36 18 1.6 0.07
9301054262
50 55 21.0 36 12.0 16 9.0 36 18 1.6 0.07
63 65 23.0 42 13.0 20 11.0 40 20 1.6 0.12
9301054264
80 65 23.0 42 13.0 20 11.0 40 20 1.6 0.12
100 75 28.5 50 16.0 25 14.0 50 25 2.0 0.21
9301054266
125 75 28.5 50 16.0 25 14.0 50 25 2.0 0.21
*Weight per item

C28 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 (Revised 03-05-09) Air Cylinders
Cylinder Mountings P1D Series
C086
Intermediate Trunnion MT4
TL TM TL
Intended for articulated mounting of cylinder. The trunnion
is factory-fitted at an optional location. Order by specifying

UW
Mounting Style G or 7 and providing the desired XV

TD
dimension (3-digit measure in mm). See page C9 for R
Ordering Information. Combined with pivot bracket
for MT4 for 32-125mm bores. L1
Standard*
Material:
Trunnion: Zinc plated steel (Cast iron for 160-200mm bores)

*Standard mounting is for the Standard cylinder body and

is permanently affixed by the factory. XVstd
C
Tie Rod Version

P1D
According to ISO MT4, VDMA 24 562, AFNOR

TM TL TD
Bore R UW L1 X1 XVmin X2 Weight

P1A
h14 h14 e9 XVmin
mm mm mm mm mm mm mm kg
mm mm mm
32 50 12 12 1.0 46 15 73.0 62.0 84.0 0.13
40 63 16 16 1.6 59 20 82.5 73.0 92.0 0.31
50 75 16 16 1.6 69 20 90.0 80.5 99.5 0.37
63 90 20 20 1.6 84 25 97.5 89.5 106.0 0.69 XVmax
80 110 20 20 1.6 102 25 110.0 98.0 122.0 0.89
100 132 25 25 2.0 125 30 120.0 110.5 129.5 1.58
125 160 25 25 2.0 155 32 145.0 132.0 158.0 2.60
160 200 32 32 2.5 190 70 C.F. 169 C.F. C.F.
200 250 32 32 2.5 242 70 C.F. 184 C.F. C.F.
XVstd = X1 + Stroke length/2 XVmax = X2 + Stroke length C.F. = Consult Factory

Flange Mounted Trunnion TL TM TL

Intended for articulated mounting of cylinder. This

trunnion can be flange mounted on the front or rear

UW
TD

end cover of all P1D cylinders. If you choose, you

can order a complete cylinder with factory-fitted flange R
L1
mounted trunnion – see the ordering information on
pages C8 and C9. Individual trunnions have part numbers
as shown below.

Material
Trunnion: zinc plated steel L1 XV1
Screws: zinc plated steel, 8.8

Delivered complete with mounting screws for

attachment to the cylinder

According to ISO MT4, VDMA 24 562, AFNOR XV2

TM TL TD
Bore R UW L1 XV1 X Weight
h14 h14 e9 Part Number
mm mm mm mm mm mm kg
mm mm mm
32 50 12 12 1.0 46 14 19.0 127.0 0.17 P1D-4KMYF
40 63 16 16 1.6 59 19 20.5 144.5 0.43 P1D-4LMYF
50 75 16 16 1.6 69 19 27.5 152.5 0.55 P1D-4MMYF
63 90 20 20 1.6 84 24 25.0 170.0 1.10 P1D-4NMYF
80 110 20 20 1.6 102 24 34.0 186.0 1.66 P1D-4PMYF
100 132 25 25 2.0 155 29 36.5 203.5 3.00 P1D-4QMYF
XV2 = X + Stroke length

C29 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Air Cylinders
Piston Rod Mountings P1D Series
C086
Swivel Rod Eye
Swivel rod eye for articulated mounting of cylinder. ØCN
N
Swivel rod eye can be combined with clevis bracket GA. ER
Maintenance-free.

Materials B
Swivel rod eye: Zinc-plated steel
Swivel bearing according to DIN 648K: Hardened steel Z Z

KK
Stainless Steel Materials

EN
O
Swivel Rod Eye Swivel rod eye: Stainless steel

C
A LE
Swivel bearing according to DIN 648K: Stainless steel CE
Use stainless steel nut (see page C31) with stainless steel
swivel rod eye.

According to ISO 8139

B B CN EN LE Stainless
Bore A CE ER N O Weight Part
min max H9 h12 KK min Z Steel Part
mm mm mm mm mm mm kg Number
mm mm mm mm mm Number
32 20 48.0 55 43 10 14 14 M10x1.25 15 17 10.5 12° 0.08 P1C-4KRS P1S-4JRT
40 22 56.0 62 50 12 16 16 M12x1.25 17 19 12.0 12° 0.12 P1C-4LRS P1S-4LRT
50 28 72.0 80 64 16 21 21 M16x1.5 22 22 15.0 15° 0.25
P1C-4MRS P1S-4MRT
63 28 72.0 80 64 16 21 21 M16x1.5 22 22 15.0 15° 0.25
80 33 87.0 97 77 20 25 25 M20x1.5 26 32 18.0 15° 0.46
P1C-4PRS P1S-4PRT
100 33 87.0 97 77 20 25 25 M20x1.5 26 32 18.0 15° 0.46
125 51 123.5 137 110 30 37 35 M27x2 36 41 25.0 15° 1.28 P1C-4RRS P1S-4RRT
160/200 56 C.F. C.F. 125 35* 43 40 M36x2 40 50 28.0 15° C.F. L075470036 C.F.
*H7 C.F. = Consult Factory

Clevis ØCK

Clevis for articulated mounting of cylinder. ER

Material
Clevis, clip: Galvanized steel B

Pin: Hardened steel

Stainless Steel Clevis Material

KK

Clevis: Stainless steel

CL
CM

O
Pin: Stainless steel
Circlips according to DIN 471: Stainless steel A LE
CE
According to ISO 8140

B B CK Stainless
Bore A CE CL CM ER LE O Weight Part
min max h11/E9 KK Steel Part
mm mm mm mm mm mm mm mm kg Number
mm mm mm Number
32 20 45.0 52 40 10 20 10 16 M10x1.25 20 28.0 0.09 P1C-4KRC P1S-4JRD
40 24 54.0 60 48 12 24 12 19 M12x1.25 24 32.0 0.15 P1C-4LRC P1S-4LRD
50 32 72.0 80 64 16 32 16 25 M16x1.5 32 41.5 0.35
P1C-4MRC P1S-4MRD
63 32 72.0 80 64 16 32 16 25 M16x1.5 32 41.5 0.35
80 40 90.0 100 80 20 40 20 32 M20x1.5 40 50.0 0.75
P1C-4PRC P1S-4PRD
100 40 90.0 100 80 20 40 20 32 M20x1.5 40 50.0 0.75
125 56 123.5 137 110 30 55 30 45 M27x2 54 72.0 2.10 P1C-4RRC P1S-4RRD
160/200 71 C.F. C.F. 144 35 70 35 57 M36x2 72 95 C.F. L075490036 C.F.
C.F. = Consult Factory

C30 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Air Cylinders
Piston Rod Mountings P1D Series
C086
Flexo Coupling
Flexo coupling for articulated mounting of piston rod.
ER EN EO EP EQ
Flexo fitting is intended to take up axial angle errors
within a range of ±4°.

DL
Material

DL
Flexo coupling, nut: Zinc-plated steel M EI M
Socket: Hardened steel EH EL
B
EK
Supplied complete with galvanized adjustment nut.

Bore
B
min
B
max DL
EH EI EK EL EN EO EP EQ ER M
Z
Weight
Part Number
C
mm mm mm mm mm mm mm mm mm mm mm kg
mm mm
32 36.0 43 M10x1.25 20 23 70 31 12 30 30 19 30 5.0 4° 0.21 P1C-4KRF

P1D
40 37.0 43 M12x1.25 23 23 67 31 12 30 30 19 30 6.0 4° 0.22 P1C-4LRF
50 53.0 61 M16x1.5 40 32 112 45 19 41 41 30 41 8.0 4° 0.67
P1C-4MRF
63 53.0 61 M16x1.5 40 32 112 45 19 41 41 30 41 8.0 4° 0.67

P1A
80 57.0 67 M20x1.5 39 42 122 56 19 41 41 30 41 10.0 4° 0.72
P1C-4PRF
100 57.0 67 M20x1.5 39 42 122 56 19 41 41 30 41 10.0 4° 0.72
125 75.5 89 M27x2 48 48 145 60 24 55 55 32 55 13.5 4° 1.80 P1C-4RRF
160/200 C.F. C.F. M36x2 72 78 251 C.F. 36 75 75 50 55 18.0 4° C.F. L075530036
C.F. = Consult Factory

Nuts
Intended for fixed mounting of accessories to the piston rod.
Material: Zinc-plated steel
All P1D cylinders are delivered with a zinc-plated steel piston
rod nut, except P1D Clean, which is delivered with a C B
stainless steel piston rod nut instead. A

Stainless Steel Nut

Material: Stainless steel A2
All P1D cylinders are delivered with a zinc-plated steel piston
rod nut, except P1D Clean, which is delivered with a
stainless steel piston rod nut instead.

Acid-proof nut
Material: Acid-proof steel A4
Cylinders with acid-proof piston rod are supplied with nut of acid-proof steel

According to DIN 439 B

Bore A B Weight Part Numbers

C
mm mm mm kg Steel Stainless Steel Acid-Proof
32 17 5.0 M10x1.25 0.007 9128985601 9126725404 0261109919
40 19 6.0 M12x1.25 0.010 0261109910 9126725405 0261109920
50 24 8.0 M16x1.5 0.021
9128985603 9126725406 0261109917
63 24 8.0 M16x1.5 0.021
80 30 10.0 M20x1.5 0.040
0261109911 0261109921 0261109916
100 30 10.0 M20x1.5 0.040
125 41 13.5 M27x2 0.100 0261109912 0261109922 0261109918
160/200 55 18.0 M36x2 C.F. L075540036 C.F. C.F.
C.F. = Consult Factory

C31 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Air Cylinders
Accessories P1D Series
C086
Screw Set for MP2, MP4, MS1 and GA
Set of stainless steel screws for fitting clevis Bore Weight
Part Number
mm kg
brackets
MP2, MP4 and GA onto the cylinder. The screws 32 0.02 9301054321
have an internal hexagonal head and are used 40 0.02 9301054321
in special environments, e.g. the food industry, 50 0.05 9301054322
or where there are extra demands for protection
against corrosion. 63 0.05 9301054322
80 0.09 9301054323
Material: 100 0.09 9301054323

C
According to DIN 912, Stainless steel, A2
125 0.15 9301054324
4 pcs per pack.

Screw set for MF1/MF2 Bore Weight

Part Number
mm kg
Set of stainless steel screws for fitting flanges
MF1/MF2 onto the cylinder. The screws have an 32 0.02 9301054331
internal hexagonal head and are used in special 40 0.02 9301054331
environments, e.g. the food industry, or where 50 0.04 9301054332
there are extra demands for protection against
63 0.04 9301054332
corrosion.
80 0.07 9301054333
Material: 100 0.07 9301054333
According to DIN 6912, Stainless steel, A2 125 0.12 9301054334

4 pcs per pack

Sealing plugs Bore Weight

Part Number
mm kg
Set of sealing plugs to be fitted in unused
end covers. 32 0.01 9121742201
The plugs can be used for all P1D cylinders to 40 0.01 9121742201
avoid collecting dirt and fluids in the end cover 50 0.02 9121742202
screw recesses.
63 0.02 9121742202
Material: 80 0.02 9121742203
Polyamid PA 100 0.02 9121742203
125 0.03 9121742204
4 pcs per pack

Pivot Pin Sets for 160-200mm Bore Cylinder Accessories

For Clevis Bracket MP2 For Rear Swivel Eye MP6
d4 Dia.
CL
EK Dia.

CD L4

L2 L1 L2
L3

Bore CD CL Part Number Bore EK d4 L1 L2 L3 L4 Part Number

160/200 30 170.50 L075500160 160/200 35 6 119 7 131 41 L075520160

C32 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Air Cylinders
Service Kits P1D Series
C086
Seal Kits Grease for P1D
Cyl.
P1D Cylinder Version Standard 30g 9127394541
Bore
Standard
mm
P1D-S, P1D-T, P1D-C, P1D-F
32 SK032P1D01
40 SK040P1D01
50 SK050P1D01
63 SK063P1D01
80 SK080P1D01
100
125
SK100P1D01
SK125P1D01 C
Gland Seal Kits

P1D
RG-Rod Gland Cartridge Kit RK-Rod Seal Kit
Bore Rod Rod Nitrile Seals Fluorocarbon Seals Nitrile Seals Fluorocarbon Seals

P1A
Size Dia. No. Consisting of: 1 each Consisting of: 1 each Consisting of: 1 each Consisting of: 1 each
items #14, 41, 45 & 104 items #14, 41, 45 & 104 items #41, 45 & 104 items #41, 45 & 104
mm mm Part No. Part No. Part No. Part No.
32 12 1 RG0P1D0121 RG0P1D0125 RK0P1D0121 RK0P1D0125
40 16 1 RG0P1D0161 RG0P1D0165 RK0P1D0161 RK0P1D0165
50 & 63 20 1 RG0P1D0201 RG0P1D0205 RK0P1D0201 RK0P1D0205
80 & 100 25 1 RG0P1D0251 RG0P1D0255 RK0P1D0251 RK0P1D0255
125 32 1 RG0P1D0321 RG0P1D0325 RK0P1D0321 RK0P1D0325

Piston & End Seal Kits

PK – Piston Seal Kit CB – Cylinder Body End Seal Kit
Consisting of: 2 each items # 42 & 47 plus
1 each items 121 and #159. NOTE: (Fluorocarbon seals Consisting of: 2 each item #47
Bore Size
do not include magnetic ring symbol #159.)
Fluorocarbon Fluorocarbon
Nitrile Seals Nitrile Seals
Seals Seals
mm Part No. Part No. Part No. Part No.
32 PK032P1D01 PK032P1D05 CB032P1D01 CB032P1D05
40 PK040P1D01 PK040P1D05 CB040P1D01 CB040P1D05
50 PK050P1D01 PK050P1D05 CB050P1D01 CB050P1D05
63 PK063P1D01 PK063P1D05 CB063P1D01 CB063P1D05
80 PK080P1D01 PK080P1D05 CB080P1D01 CB080P1D05
100 PK100P1D01 PK100P1D05 CB100P1D01 CB100P1D05
125 PK125P1D01 PK125P1D05 CB125P1D01 CB125P1D05

C33 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 P1A Series
Mini ISO 6432
Pneumatic Cylinders

P1D
P1A

Contents
Features...........................................................................C36
Ordering Information/Stroke Lengths...............................C37
Technical Data.......................................................... C38-C40
Dimensions.......................................................................C41
Cylinder Mountings................................................... C42-C43

C35 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Air Cylinders
Features P1A Series
C086
Anodized aluminium
Low-friction piston Magnet for proximity
end caps.
rod seal. sensing.

Stainless steel
piston rod.

C
Smooth stainless steel Low-friction piston.
cylinder body.

The Parker P1A series of pneumatic cylinders are intended for Double Acting
use in a wide range of applications. These cylinders are par-
ticularly suitable for lighter duties in the packaging, food and
textile industries. Hygienic design, the use of corrosion-resist-
ant materials and initial lubrication with our food-grade grease
makes the cylinders suitable for food industry applications.
Proven design and high quality manufacturing throughout
ensure long service life and optimum performance.
Mounting dimensions are in accordance with ISO 6432 and
CETOP RP52P. This greatly simplifies installation and world- Double Acting, Double Rod
wide interchangeability.

The Mini ISO range is available with bumpers or adjustable

pneumatic cushioning. Controlled by simple bleed screws for
fine adjustment, the adjustable cushioned cylinders can be
operated with higher mass loads and at higher speeds than
those with fixed end cushioning bumpers.

The Mini ISO range is also available in an all-stainless ver-

sion with piston rod, cylinder body and end covers of stain- Single-Acting, Spring Return
less steel for use in extremely severe environments. Consult
the Wadsworth, Ohio facility for more information.

A complete range of sensors for proximity sensing is avail-

able as accessories: both reed and solid state sensors are
available. Either can be supplied with flying leads or cable
and multi-pin connector. See Electronic Sensors section for
specifications and part numbers.

Single-Acting, Spring Extend

C36 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Air Cylinders
Ordering Information P1A Series
C086
Order Key

P1A – S 016 M S – 0025

Stroke length, mm
E.g. 0025 = 25 mm
For standard stroke length
and max length see table
Cylinder Bore Cylinder Type / Function below.
010
012
10mm
12mm
M Double-acting, adjustable cushioning.
Ø16-25 mm. Not for sealing material
type F and L
Sealing material C
016 16mm S Standard
D Double-acting, bumpers, Ø10 - Ø25 -20°C to +80°C (-4°F to +176°F)
020 20mm
Magnetic piston

P1D
025 25mm
F Double-acting, adjustable cushioning, F High temperature:
double rod, Ø16-25 mm. Not for Ø10, 12 and 16 mm
sealing material type F and L. -10°C to +120°C (14°F to 248°F)

P1A
K Double-acting, bumpers, double rod, Ø20 and 25 mm
Ø10 - Ø25 -10°C to +150°C. (14°F to 302°F)
H Double-acting, adjustable cushioning, Non magnetic piston
double rod (hollow), Ø20-25 mm, L Low temperature
max. stroke 125 mm. Not for sealing -40°C to +60°C (-40°F to +140°F)
material type F and L. Non magnetic piston
P Double-acting, bumpers, double rod N No PTFE or copper
(hollow), Ø20-25 mm, max. stroke Standard seals
125 mm -20°C to +60°C (-4°F to +140°F)
S Single-acting, bumpers, spring return Magnetic piston
for retract stroke, Ø10-25 mm V External seals of fluorinated rubber
T Single-acting, bumpers, spring extend -20°C to +80°C (-4°F to +176°F)
for advance stroke, Ø16-25 mm Magnetic piston

Stroke Lengths
Cylinder Bore Stroke Length (l = standard, l = non-standard, blank = N/A)
Model Size 10 15 20 25* 30 40 50* 80* 100* 125* 160* 200* 250* 320* 400* 500*
Double acting with fixed end-cushioning:
P1A-S 010 D 10 l l l l l l l l l l l l l l l l
P1A-S 012 D 12 l l l l l l l l l l l l l l l l
P1A-S 016 D 16 l l l l l l l l l l l l l l l l
P1A-S 020 D 20 l l l l l l l l l l l l l l l l
P1A-S 025 D 25 l l l l l l l l l l l l l l l l
Double acting with adjustable end-cushioning:
P1A-S 016 M 16 l l l l l l l l l l l l l l
P1A-S 020 M 20 l l l l l l l l l l l l l l
P1A-S 025 M 25 l l l l l l l l l l l l l l
Single acting:
P1A-S 010 SS 10 l l l l l l l l
P1A-S 012 SS 12 l l l l l l l l
P1A-S 016 SS(TS) 16 l l l l l l l l**
P1A-S 020 SS(TS) 20 l l l l l l l l
P1A-S 025 SS(TS) 25 l l l l l l l l
*Standard stroke lengths in mm according to ISO 4393
** Not for the TS version

Note: For sensor specifications and part numbers, please refer to the Electronic Sensors section.

C37 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Air Cylinders
Technical Data P1A Series
C086
Standard Specifications
Working pressure max 10bar (145 PSI)
Working temperature max +80°C (176°F)
min –20°C (4°F)
High-temperature version max +150°C (Ø20 and 25 mm) 302°F
+120°C (Ø10, 12 and 16 mm) 248°F
min –10°C 14°F
Low-temperature version max +60°C 140°F
min –40°C -40°F
Prelubricated, further lubrication is not normally necessary.

C If additional lubrication is introduced it must be continued.

Material Specification
Piston rod Stainless steel, DIN X 10 CrNiS 18 9
Piston rod seal Fluorocarbon rubber FPM Variants Mini ISO:
Piston rod bearing Multilayer PTFE/steel Low-temperature version, type L:
End covers Anodized aluminium Piston rod seal Nitrile rubber, NBR
O-ring, internal Nitrile rubber, NBR Piston complete Nitrile rubber, NBR/steel
Cylinder barrel Stainless steel, DIN X 5 CrNi 18 10
Piston, complete Nitrile rubber, NBR/steel High-temperature version, type F:
Magnet holder Thermoplastic elastomer Piston rod seal Fluorocarbon rubber, FPM
Magnet Plastic-coated magnetic material Piston complete, Ø10-Ø16 HNBR/steel
Return spring Surface-treated steel Piston complete, Ø20-Ø25 FPM/steel
Cushioning screw Stainless steel, DIN X 10 CrNiS 18 9 PTFE and copper free cylinders, type N:
Piston rod bearing PA plastic
Cylinders are supplied complete with nose mounting and piston Cylinders with outer sealings in fluorcarbon, type V:
rod nuts. Piston rod seal/
Cylinders with double piston rods are supplied with two piston Scraper ring Fluorocarbon rubber, FPM
rod nuts
Note: Spare part = new cylinder

Quick Reference
Cylinder Piston Rod Additional
Total Weight at
Weight per Port
Model # Bore Area Dia. Area Thread 0mm Stroke Air Consumption
10mm Stroke Size
(mm) (cm2) (mm) (cm2) (lbs)
(lbs)
Double acting, cushioned stroke
P1A-S 010 D 10 0.78 4 0.13 M4 0.09 0.007 0.0004 1) M5
P1A-S 012 D 12 1.13 6 0.28 M6 0.15 0.009 0.0005 1) M5
P1A-S 016 D 16 2.01 6 0.28 M6 0.20 0.012 0.0009 1) M5
P1A-S 020 D 20 3.14 8 0.50 M8 0.40 0.015 0.0010 1) G1/8
P1A-S 025 D 25 4.91 10 0.78 M10x1.25 0.89 0.025 0.0023 1) G1/8
Double acting, adjustable cushioning
P1A-S 016 M 16 2.01 6 0.28 M6 0.20 0.012 0.0009 1) M5
P1A-S 020 M 20 3.14 8 0.50 M8 0.40 0.015 0.0010 1) G1/8
P1A-S 025 M 25 4.91 10 0.78 M10x1.25 0.89 0.025 0.0023 1) G1/8
Single acting
P1A-S 010 SS 10 0.78 4 0.13 M4 0.09 0.007 0.0002 1) M5
P1A-S 012 SS 12 1.13 6 0.28 M6 0.18 0.009 0.0003 1) M5
P1A-S 016 SS(TS) 16 2.01 6 0.28 M6 0.22 0.012 0.0005 1) M5
P1A-S 020 SS(TS) 20 3.14 8 0.50 M8 0.40 0.015 0.0008 1) G1/8
P1A-S 025 SS(TS) 25 4.91 10 0.78 M10x1.25 0.58 0.025 0.0013 1) G1/8

1) Free air consumption per 10 mm stroke length for a double stroke at 6 bar (87 PSI)

C38 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Air Cylinders
Technical Data P1A Series
C086
Cylinder Forces
Indicated cylinder forces are theoretical and should be reduced according to the working conditions.

Double Acting
Theoretical Piston Force (lbs)
Bore Size at 6 Bar (87 PSI)
Model Number
mm
Extension Retraction
P1A-S 010 D 10 10.57 8.76
P1A-S 012 D 12 15.07 11.25
P1A-S 016 D 16 26.98 23.15
P1A-S 020 D
P1A-S 025 D
20
25
42.27
66.10
35.52
55.53
C
P1A-S 016 M 16 26.98 23.16

P1D
P1A-S 020 M 20 42.27 35.52
P1A-S 025 M 25 66.10 55.53

Single Acting

P1A
Theoretical Piston Force (lbs) at 6 Bar (87 PSI)
Model Number Stroke Spring Retraction Spring Extension
lbs max lbs. min lbs. max lbs. min
10 8.5 8.1 2.4 2.0
15 8.5 8.1 2.4 2.0
25 8.7 8.1 2.4 2.0
P1A-S 010 SS
40 8.5 7.6 2.9 2.0
50 8.7 7.6 2.9 1.7
80 8.7 7.6 2.9 1.7
10 11.9 11.4 3.6 3.1
15 11.9 11.4 3.6 3.1
25 12.3 11.4 3.6 2.7
P1A-S 012 SS
40 11.9 10.8 4.2 3.3
50 11.9 10.8 4.2 3.1
80 12.3 10.8 4.2 2.7
10 22.0 (19.1) 22.2 (18.8) 4.7 (4.2) 4.0 (4.0)
15 23.1 (19.3) 22.2 (18.8) 4.7 (4.2) 3.8 (3.8)
25 23.8 (19.8) 22.2 (18.8) 4.7 (4.2) 3.3 (3.3)
P1A-S 016 SS(TS)
40 23.8 (20.3) 21.3 (18.8) 5.6 (4.2) 3.1 (3.1)
50 24.2 (20.4) 21.3 (18.8) 5.6 (4.2) 2.7 (2.7)
80 24.0 (21.3) 21.3 (18.8) 5.6 (4.2) 2.9 (2.9)
10 36.6 (29.6) 36.1 (29.2) 6.1 (6.3) 5.6 (5.8)
15 36.8 (29.8) 36.1 (29.2) 6.1 (6.3) 5.4 (5.6)
25 37.5 (30.3) 36.1 (29.2) 6.1 (6.3) 4.7 (5.1)
P1A-S 020 SS(TS)
40 37.3 (31.0) 35.7 (29.2) 6.5 (6.3) 4.9 (4.9)
50 37.7 (31.4) 35.7 (29.2) 6.5 (6.3) 4.5 (4.5)
80 38.2 (31.2) 36.1 (24.2) 6.1 (11.2) 4.0 (4.2)
10 57.5 (46.1) 56.9 (45.6) 9.2 (9.9) 8.5 (9.4)
15 58.0 (46.5) 56.9 (45.6) 9.2 (9.9) 8.1 (9.0)
25 58.9 (47.2) 56.9 (45.6) 9.2 (9.9) 7.2 (8.3)
P1A-S 025 SS(TS)
40 58.7 (48.1) 56.2 (45.6) 9.9 (9.9) 7.4 (7.4)
50 59.4 (48.8) 56.2 (45.6) 9.9 (9.9) 6.7 (6.7)
80 59.4 (50.1) 56.4 (46.3) 9.6 (9.2) 6.7 (5.4)

C39 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Air Cylinders
Technical Data P1A Series
C086
Cushioning Double-acting cushioned cylinders
Use the diagram below to determine the necessary size of Adjustable pneumatic cushioning permits greater loads and
cylinder to provide the requisite cushioning performance. higher operating speeds, making the cylinders suitable for
The maximum cushioning performance, as indicated in the more demanding applications.
diagram, is based on the following assumptions: These cylinders are available in bores of 16, 20 and 25 mm,
  - Low load, i.e. low pressure drop across the piston with stroke lengths from 20 mm to 500 mm.
  - Steady-state piston speed
  - Correctly adjusted cushioning screw
The load is the sum of the internal and external friction,
together with any gravity forces. At high relative loading it is

C recommended that, for a given speed, the load should be

reduced by a factor of 2.5, or that, for a given mass, the speed
should be reduced by a factor of 1.5. These factors apply
in relation to the maximum performance as shown in the
diagram.

Fixed End-Cushioning (Bumpers)

Speed Ft./Sec.
6.57
5.25
3.94
3.28
2.63 Ø2
5
Ø2
0
1.64 Ø1
6
Ø1
2
.98 Ø1
0

.66

.33
.22 .44 .66 1.1 1.8 2.2 4.4 6.6 11 17.65 33 44 66
22.05
Weight Lbs.

Adjustable Pneumatic End-Cushioning

Speed Ft./Sec.
9.8
8.2
6.51
Ø2
5
4.9

3.28 Ø2
0
2.63

1.64
1.31

.98

.66
.66 1.1 1.8 2.2 3.3 4.4 6.6 8.8 11 17.65 22.05 33 44 66
Weight Lbs.

C40 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Air Cylinders
Dimensions P1A Series
C086
Double acting cylinders ZJ C

EW
XC AM

ØKK
ØBE

ØBE
ØCD

H
L AF
SW
Single Acting
Double piston rod BF P WH
WH + stroke

AF EE
C

P1D
ØKK
ØBE

P1A
Cylinder bore AM 0/-2 AF BF C CD h9 EW H KK L SW WH±1.2
BE EE
mm mm mm mm mm mm mm mm mm mm mm
10 12 M12x1.25 12 10 14.0 4 M5 8 16.7 M4 6 – 16
12 16 M16x1.5 18 13 18.0 6 M5 12 19.1 M6 9 5 22
161) 16 M16x1.5 18 13 18.0 6 M5 12 19.1 M6 9 5 22
162) 16 M16x1.5 18 13 25.0 6 M5 12 24.0 M6 9 5 22
20 20 M22x1.5 20 14 24.0 8 G1/8 16 27.0 M8 12 7 24
25 22 M22x1.5 22 14 27.5 8 G1/8 16 29.0 M10x1.25 12 9 28
1) P1A-S016DS/SS/TS 2) P1A-S016MS

Double acting cylinders

Cylinder bore XC ZJ P
mm mm mm mm
10 64 + stroke 84 + stroke 46 + stroke
12 75 + stroke 99 + stroke 48 + stroke
16 82 + stroke 104 + stroke 53 + stroke
20 95 + stroke 125 + stroke 67 + stroke
25 104 + stroke 132 + stroke 68 + stroke

Single-acting, spring return, type SS

Cylinder Bore XC (mm) at Various Strokes ZJ (mm) at Various Strokes P (mm) at Various Strokes
mm 10 15 25 40 50 80 10 15 25 40 50 80 10 15 25 40 50 80
10 74 79 89 126 136 174 94 99 109 146 156 194 56 61 71 108 118 156
12 85 90 100 132 142 185 109 114 124 156 166 209 58 63 73 105 115 158
16 92 97 107 122 132 184 114 119 129 144 154 206 63 68 78 93 103 155
20 105 110 120 135 145 191 135 140 150 165 175 221 77 82 92 107 117 163
25 114 119 129 144 154 201 142 147 157 172 182 229 78 83 93 108 118 165
Single-acting, spring-extended, type TS
Cylinder Bore ZC 3) (mm) at Various Strokes ZJ 3) (mm) at Various Strokes P (mm) at Various Strokes
mm 10 15 25 40 50 80 10 15 25 40 50 80 10 15 25 40 50 80
16 107 112 122 137 147 – 134 139 149 164 174 – 78 83 93 108 118 –
20 120 125 135 150 160 195 156 161 171 186 196 231 92 97 107 122 132 167
25 129 134 144 159 169 205 165 170 180 195 205 241 93 98 108 123 133 169
3) With piston rod retracted, as shown in the dimension drawing
Length tolerances ±1 mm Stroke length tolerance +1.5/0 mm

C41 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Air Cylinders
Cylinder Mountings P1A Series
C086
Flange - MF8
Intended for fixed attachment of the cylinder. The flange is designed for
mounting on the front or rear end-covers.
A
Material: Surface-treated steel
This mounting is also available in stainless steel.
Consult the Wadsworth, Ohio facility for additional information.

D
Cylinder Weight
Part Number A B C D E F B
Ø mm lbs C
P1A-4CMB 10 4.5 30 40 22 3 13 0.025
P1A-4DMB 12-16 5.5 40 52 30 4 18 0.055

C P1A-4HMB
20
25
6.6
6.6
50
50
66
66
40
40
5
5
19
23
0.100
0.100
E F

Foot - MS3
Intended for fixed attachement of the cylinder. The bracket is designed
for mounting on the front or rear end-covers.
Material: Surface-treated steel

G
This mounting is also available in stainless steel.

E
B
Consult the Wadsworth, Ohio facility for additional information.
C
D
Cylinder A B C D E F G H I Weight
Part Number
Ø mm mm mm mm mm mm mm mm mm mm lbs
P1A-4CMF 10 4.5 16 25 35 3 24 26.0 16 11 0.045
P1A-4DMF 12-16 5.5 20 32 42 4 32 32.5 20 14 0.08 A
I
20 6.5 25 40 54 5 36 45.0 25 17 0.18
P1A-4HMF F
25 6.5 25 40 54 5 40 45.0 25 17 0.18 H

Cover Trunnion
Intended for articulated mounting of the cylinder. The flange is designed
for mounting on the front or rear end-covers.
Material: Stainless steel, DIN X 10 CrNiS 18 9
C
B
ØA

Cylinder A B h14 C D E e9 F G H Weight

Part Number
ØF

Ø mm mm mm mm mm mm mm mm mm lbs
D
E

P1A-4CMJ 10 12.5 26 38 20 8 4 6 10 0.03

P1A-4DMJ 12-16 16.5 38 58 25 10 6 8 14 0.07
20 22.5 46 66 30 10 6 8 16 0.08
P1A-4HMJ
25 22.5 46 66 30 10 6 8 20 0.08
G H

Mounting Nut
Intended for fixed mounting of the cylinder.
Cylinders are supplied complete with one mounting nut.
Material: Galvanized steel
A
This nut is also available in stainless steel.
Consult the Wadsworth, Ohio facility for further information.
C

Cylinder A B C Weight
Part Number
Ø mm mm mm mm lbs B
9127385101 10 16 3 M12x1.25 0.02
9127385102 12-16 20 4 M16x1.50 0.04
9127385103 20-25 27 5 M22x1.50 0.09

C42 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Air Cylinders
Cylinder Mountings P1A Series
C086
Clevis Bracket
Intended for articulated mounting of the cylinder. Supplied with
shaft for mounting on the rear end cover.
Material:
H
Bracket: surface-treated steel, black
Pin: surface hardened steel I
Circlips: according to DIN 471: Stainless steel

D
This mounting is also available in stainless steel.
Consult the Wadsworth, Ohio facility for additional information. E G + Stroke
F
J

C
Part Cylinder A B C D E F G H I J Weight
Number Ø mm mm mm mm mm mm mm mm mm ° ° lbs
P1A-4CMT 10 4.5 13 8 24 12.5 20 65.3 5 160 17 0.045
12 5.5 18 12 27 15.0 25 73.0 7 170 15 0.08 A
P1A-4DMT

P1D
16 5.5 18 12 27 15.0 25 80.0 7 170 15 0.08 C

20 6.5 24 16 30 20.0 32 91.0 10 165 10 0.18 B

P1A-4HMT
25 6.5 24 16 30 20.0 32 100.0 10 165 10 0.18

P1A
Clevis
According to ISO 8140. Intended for articulated mounting of the cylinder.
This mounting is adjustable in the axial direction. Supplied complete with pin. I±J
Material: Galvanized steel
This mounting is also available in stainless steel.

D
Consult the Wadsworth, Ohio facility for additional information.
C G
Part Cylinder A C D E F G H I J Weight E F
B
Number Ø mm mm mm mm mm mm mm mm mm mm lbs
P1A-4CRC 10 4 M4 2.2 8 8 5 16 4 22.0 2.0 0.015

H
D
B
P1A-4DRC 12-16 6 M6 3.2 12 12 7 24 6 31.0 3.0 0.05 A
P1A-4HRC 20 8 M8 4.0 16 16 10 32 8 40.5 3.5 0.10
P1A-4JRC 25 10 M10x1.25 5.0 20 20 12 40 10 49.0 3.0 0.21

Swivel Rod Eye A

According to ISO 8139. Intended for articulated mounting of the cylinder.

This mounting is adjustable in the axial direction.
Material:
J±L
Swivel rod eye: Galvanized steel
C G
Ball: hardened steel
This mounting is also available in stainless steel.

D
H
B

Consult the Wadsworth, Ohio facility for additional information.

I E F
Part Cylinder A C D E F G H I J K L Weight
B
Number Ø mm mm mm mm mm mm mm mm mm mm mm mm lbs
P1A-4CRS 10 5 M4 2.2 8 10 9 27 6.0 8 33.0 9 2.0 0.04
P1A-4DRS 12-16 6 M6 3.2 9 10 10 30 6.8 9 38.5 11 1.5 0.06
P1A-4HRS 20 8 M8 4.0 12 12 12 36 9.0 12 46.0 14 2.0 0.10
P1A-4JRS 25 10 M10x1.25 5.0 14 14 14 43 10.5 15 52.5 17 2.5 0.19

Rod Nut
Intended for fixed mounting on the piston rod. Cylinders are supplied complete with one rod nut.
(cylinders with double piston rod are supplied with two rod nuts.)
Material: Galvanized steel
This nut is also available in stainless steel. Consult the Wadsworth, Ohio facility for additional information. F
Cylinder D F E Weight
Part Number
Ø mm mm mm mm lbs
D

0261110600 10 M4 7 2.2 0.002

0261210800 12-16 M6 10 3.2 0.004 E

0261211000 20 M8 13 4.0 0.010

9128985601 25 M10x1.25 17 5.0 0.015

C43 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Pneumatic Actuator Products
Safety Guide General Information
Safety Guide for Selecting and Using Hydraulic, Pneumatic Cylinders and Their Accessories
WARNING: ! Failure of the cylinder, its parts, its mounting, its connections to other objects,
or its controls can result in:
• Unanticipated or uncontrolled movement of the cylinder or objects connected to it.
• Falling of the cylinder or objects held up by it.
• Fluid escaping from the cylinder, potentially at high velocity.
These events could cause death or personal injury by, for example, persons falling from
high locations, being crushed or struck by heavy or fast moving objects, being pushed into
dangerous equipment or situations, or slipping on escaped fluid.
Before selecting or using Parker (The Company) cylinders or related accessories, • Unexpected detachment of the machine member from the piston rod.
it is important that you read, understand and follow the following safety informa- • Failure of the pressurized fluid delivery system (hoses, fittings, valves,
tion. Training is advised before selecting and using The Company’s products. pumps, compressors) which maintain cylinder position.
1.0 General Instructions • Catastrophic cylinder seal failure leading to sudden loss of pressurized
1.1 Scope – This safety guide provides instructions for selecting and using fluid.
(including assembling, installing, and maintaining) cylinder products. This • Failure of the machine control system.
safety guide is a supplement to and is to be used with the specific Company
publications for the specific cylinder products that are being considered for Follow the recommendations of the “Piston Rod Selection Chart and Data”
use. in the publication for the series of cylinders of interest. The suggested piston
rod diameter in these charts must be followed in order to avoid piston rod
1.2 Fail Safe – Cylinder products can and do fail without warning for many buckling.
reasons. All systems and equipment should be designed in a fail-safe mode Piston rods are not normally designed to absorb bending moments or loads
so that if the failure of a cylinder product occurs people and property won’t which are perpendicular to the axis of piston rod motion. These additional
be endangered. loads can cause the piston rod to fail. If these types of additional loads are
1.3 Distribution – Provide a free copy of this safety guide to each person expected to be imposed on the piston rod, their magnitude should be made
responsible for selecting or using cylinder products. Do not select or use known to our engineering department.
The Company’s cylinders without thoroughly reading and understanding this The cylinder user should always make sure that the piston rod is securely
safety guide as well as the specific Company publications for the products attached to the machine member.
considered or selected.
On occasion cylinders are ordered with double rods (a piston rod extended
1.4 User Responsibility – Due to very wide variety of cylinder applications from both ends of the cylinder). In some cases a stop is threaded on to one
and cylinder operating conditions, The Company does not warrant that of the piston rods and used as an external stroke adjuster. On occasions
any particular cylinder is suitable for any specific application. This safety spacers are attached to the machine member connected to the piston rod
guide does not analyze all technical parameters that must be considered and also used as a stroke adjuster. In both cases the stops will create a
in selecting a product. The hydraulic and pneumatic cylinders outlined in pinch point and the user should consider appropriate use of guards. If these
this catalog are designed to The Company’s design guidelines and do not external stops are not perpendicular to the mating contact surface, or if
necessarily meet the design guideline of other agencies such as American debris is trapped between the contact surfaces, a bending moment will be
Bureau of Shipping, ASME Pressure Vessel Code etc. The user, through its placed on the piston rod, which can lead to piston rod failure. An external
own stop will also negate the effect of cushioning and will subject the piston rod
analysis and testing, is solely responsible for: to impact loading. Those two (2) conditions can cause piston rod failure.
• Making the final selection of the cylinders and related accessories. Internal stroke adjusters are available with and without cushions. The
use of external stroke adjusters should be reviewed with our engineering
• Determining if the cylinders are required to meet specific design department.
requirements as required by the Agency(s) or industry standards covering
the design of the user’s equipment. The piston rod to piston and the stud to piston rod threaded connections
are secured with an anaerobic adhesive. The strength of the adhesive
• Assuring that the user’s requirements are met, OSHA requirements are decreases with increasing temperature. Cylinders which can be exposed to
met, and safety guidelines from the applicable agencies such as but not temperatures above +250°F (+121°C) are to be ordered with a non studded
limited to ANSI are followed and that the use presents no health or safety piston rod and a pinned piston to rod joint.
hazards.
• Providing all appropriate health and safety warnings on the equipment on 2.3 Cushions – Cushions should be considered for cylinder applications
which the cylinders are used. when the piston velocity is expected to be over 4 inches/second.
Cylinder cushions are normally designed to absorb the energy of a linear
1.5 Additional Questions – Call the appropriate Company technical
applied load. A rotating mass has considerably more energy than the same
service department if you have any questions or require any additional
mass moving in a linear mode. Cushioning for a rotating mass application
information. See the Company publication for the product being considered
should be review by our engineering department.
or used, or call 1-800-CPARKER, or go to www.parker.com, for telephone
numbers of the appropriate technical service department. 2.4 Cylinder Mountings – Some cylinder mounting configurations may
have certain limitations such as but not limited to minimum stroke for side or
2.0 Cylinder and Accessories Selection
foot mounting cylinders or pressure de-ratings for certain mounts. Carefully
2.1 Seals – Part of the process of selecting a cylinder is the selection of review the catalog for these types of restrictions.
seal compounds. Before making this selection, consult the “seal information Always mount cylinders using the largest possible high tensile alloy steel
page(s)” of the publication for the series of cylinders of interest.
socket head cap screws that can fit in the cylinder mounting holes and
The application of cylinders may allow fluids such as cutting fluids, wash torque them to the manufacturer’s recommendations for their size.
down fluids etc. to come in contact with the external area of the cylinder.
These fluids may attack the piston rod wiper and or the primary seal and 2.5 Port Fittings – Hydraulic cylinders applied with meter out or
must be taken into account when selecting and specifying seal compounds. deceleration circuits are subject to intensified pressure at piston rod end.
Dynamic seals will wear. The rate of wear will depend on many operating The rod end pressure is approximately equal to:
factors. Wear can be rapid if a cylinder is mis-aligned or if the cylinder has operating pressure x effective cap end area
been improperly serviced. The user must take seal wear into consideration
in the application of cylinders. effective rod end piston area
Contact your connector supplier for the pressure rating of individual
2.2 Piston Rods – Possible consequences of piston rod failure or connectors.
separation of the piston rod from the piston include, but are not limited to
are: 3.0 Cylinder and Accessories Installation and Mounting
• Piston rod and or attached load thrown off at high speed. 3.1 Installation
• High velocity fluid discharge. 3.1.1 – Cleanliness is an important consideration, and cylinders are
• Piston rod extending when pressure is applied in the piston shipped with the ports plugged to protect them from contaminants

N
retract mode. entering the ports. These plugs should not be removed until the piping
is to be installed. Before making the connection to the cylinder ports,
Piston rods or machine members attached to the piston rod may move piping should be thoroughly cleaned to remove all chips or burrs which
suddenly and without warning as a consequence of other conditions might have resulted from threading or flaring operations.
occurring to the machine such as, but not limited to:

N8 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
Catalog 0900P-4 Pneumatic Actuator Products
Safety Guide General Information
3.1.2 – Cylinders operating in an environment where air drying damaged seals. Examine the piston rod for dents, gouges or score
materials are present such as fast-drying chemicals, paint, or weld marks, and replace piston rod if surface is rough.
splatter, or other hazardous conditions such as excessive heat, should Rod seal leakage could also be traced to gland wear. If clearance
have shields installed to prevent damage to the piston rod and piston is excessive, replace rod bushing and seal. Rod seal leakage can
rod seals. also be traced to seal deterioration. If seals are soft or gummy or
3.1.3 – Proper alignment of the cylinder piston rod and its mating brittle, check compatibility of seal material with lubricant used if
component on the machine should be checked in both the extended air cylinder, or operating fluid if hydraulic cylinder. Replace with
and retracted positions. Improper alignment will result in excessive rod seal material, which is compatible with these fluids. If the seals
gland and/or cylinder bore wear. On fixed mounting cylinders attaching are hard or have lost elasticity, it is usually due to exposure to
the piston rod while the rod is retracted will help in achieving proper temperatures in excess of 165°F. (+74°C). Shield the cylinder
alignment. from the heat source to limit temperature to 350°F. (+177°C.) and
replace with fluorocarbon seals.
3.1.4 – Sometimes it may be necessary to rotate the piston rod in
order to thread the piston rod into the machine member. This operation 4.2.1.2 – Cylinder body seal leak can generally be traced to loose
must always be done with zero pressure being applied to either side of tie rods. Torque the tie rods to manufacturer’s recommendation for
the piston. Failure to follow this procedure may result in loosening the that bore size.
piston to rod-threaded connection. In some rare cases the turning of Excessive pressure can also result in cylinder body seal leak.
the piston rod may rotate a threaded piston rod gland and loosen it from Determine maximum pressure to rated limits. Replace seals and
the retorque tie rods as in paragraph above. Excessive pressure
cylinder head. Confirm that this condition is not occurring. If it does, can also result in cylinder body seal leak. Determine if the
re-tighten the piston rod gland firmly against the cylinder head. pressure rating of the cylinder has been exceeded. If so, bring the
For double rod cylinders it is also important that when attaching or operating pressure down to the rating of the cylinder and have the
detaching the piston rod from the machine member that the torque be tie rods replaced.
applied to the piston rod end of the cylinder that is directly attaching to Pinched or extruded cylinder body seal will also result in a leak.
the machine member with the opposite end unrestrained. If the design Replace cylinder body seal and retorque as in paragraph above.
of the machine is such that only the rod end of the cylinder opposite to
Cylinder body seal leakage due to loss of radial squeeze which
where the rod attaches to the machine member can be rotated, consult
shows up in the form of flat spots or due to wear on the O.D. or
the factory for further instructions.
I.D. – Either of these are symptoms of normal wear due to high
3.2 Mounting Recommendations cycle rate or length of service. Replace seals as per paragraph
3.2.1 – Always mount cylinders using the largest possible high tensile above.
alloy steel socket head screws that can fit in the cylinder mounting 4.2.2 – Internal Leakage
holes and torque them to the manufacturer’s recommendations for their
size. 4.2.2.1 – Piston seal leak (by-pass) 1 to 3 cubic inches per minute
leakage is considered normal for piston ring construction. Virtually
3.2.2 – Side-Mounted Cylinders – In addition to the mounting bolts, no static leak with lipseal type seals on piston should be expected.
cylinders of this type should be equipped with thrust keys or dowel pins Piston seal wear is a usual cause of piston seal leakage. Replace
located so as to resist the major load. seals as required.
3.2.3 – Tie Rod Mounting – Cylinders with tie rod mountings are 4.2.2.2 – With lipseal type piston seals excessive back pressure
recommended for applications where mounting space is limited. The due to over-adjustment of speed control valves could be a direct
standard tie rod extension is shown as BB in dimension tables. Longer cause of rapid seal wear. Contamination in a hydraulic system
or shorter extensions can be supplied. Nuts used for this mounting style can result in a scored cylinder bore, resulting in rapid seal wear. In
should be torqued to the same value as the tie rods for that bore size. either case, replace piston seals as required.
3.2.4 – Flange Mount Cylinders – The controlled diameter of the rod 4.2.2.3 – What appears to be piston seal leak, evidenced by the
gland extension on head end flange mount cylinders can be used fact that the cylinder drifts, is not always traceable to the piston. To
as a pilot to locate the cylinders in relation to the machine. After make sure, it is suggested that one side of the cylinder piston be
alignment has been obtained, the flanges may be drilled for pins or pressurized and the fluid line at the opposite port be disconnected.
dowels to prevent shifting. Observe leakage. If none is evident, seek the cause of cylinder
drift in other component parts in the circuit.
3.2.5 – Trunnion Mountings – Cylinders require lubricated bearing
blocks with minimum bearing clearances. Bearing blocks should be 4.2.3 – Cylinder Fails to Move the Load
carefully aligned and rigidly mounted so the trunnions will not be
subjected to bending moments. The rod end should also be pivoted 4.2.3.1 – Pneumatic or hydraulic pressure is too low. Check the
with the pivot pin in line and parallel to axis of the trunnion pins. pressure at the cylinder to make sure it is to circuit requirements.
3.2.6 – Clevis Mountings – Cylinders should be pivoted at both ends 4.2.3.2 – Piston Seal Leak – Operate the valve to cycle the
with centerline of pins parallel to each other. After cylinder is mounted, cylinder and observe fluid flow at valve exhaust ports at end of
be sure to check to assure that the cylinder is free to swing through its cylinder stroke. Replace piston seals if flow is excessive.
working arc without interference from other machine parts. 4.2.3.3 – Cylinder is undersized for the load – Replace cylinder
with one of a larger bore size.
4.0 Cylinder and Accessories Maintenance, Troubleshooting
and Replacement 4.3 Erratic or Chatter Operation
4.1 Storage – At times cylinders are delivered before a customer is ready 4.3.1 – Excessive friction at rod gland or piston bearing due to load
to install them and must be stored for a period of time. When storage is misalignment – Correct cylinder-to-load alignment.
required the following procedures are recommended. 4.3.2 – Cylinder sized too close to load requirements – Reduce load or
4.1.1 – Store the cylinders in an indoor area which has a dry, clean and install larger cylinder.
noncorrosive atmosphere. Take care to protect the cylinder from both 4.3.3 – Erratic operation could be traced to the difference between
internal corrosion and external damage. static and kinetic friction. Install speed control valves to provide a back
4.1.2 – Whenever possible cylinders should be stored in a vertical pressure to control the stroke.
position (piston rod up). This will minimize corrosion due to possible
condensation which could occur inside the cylinder. This will also 4.4 Cylinder Modifications, Repairs, or Failed Component – Cylinders
minimize seal damage. as shipped from the factory are not to be disassembled and or modified.
If cylinders require modifications, these modifications must be done at
4.1.3 – Port protector plugs should be left in the cylinder until the time of company locations or by The Company’s certified facilities. The Cylinder
installation. Division Engineering Department must be notified in the event of a
4.1.4 – If a cylinder is stored full of hydraulic fluid, expansion of the fluid mechanical fracture or permanent deformation of any cylinder component
due to temperature changes must be considered. Installing a check (excluding seals). This includes a broken piston rod, tie rod, mounting
valve with free flow out of the cylinder is one method. accessory or any other cylinder component. The notification should include
all operation and application details. This information will be used to provide
4.1.5 – When cylinders are mounted on equipment that is stored an engineered repair that will prevent recurrence of the failure.
outside for extended periods, exposed unpainted surfaces, e.g.
piston rod, must be coated with a rust-inhibiting compound to prevent It is allowed to disassemble cylinders for the purpose of replacing seals or
corrosion. seal assemblies. However, this work must be done by strictly following all
the instructions provided with the seal kits.

N
4.2 Cylinder Trouble Shooting
4.2.1 – External Leakage
4.2.1.1 – Rod seal leakage can generally be traced to worn or

N9 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics
 Catalog 0900P-4 Pneumatic Actuator Products
Offer of Sale General Information

Offer of Sale
The items described in this document and other documents or descriptions provided by Parker Hannifin Corporation, its subsidiaries and Divisions
(“Company”) and its authorized distributors, are hereby offered for sale at prices to be established by the Company, its subsidiaries and its authorized
distributors. This offer and its acceptance by any customer (“Buyer”) shall be governed by all of the following Terms and Conditions. Buyer’s order for any
such item, when communicated to the Company, its subsidiary or an authorized distributor (“Seller”) verbally or in writing, shall constitute acceptance
of this offer.
1. Terms and Conditions of Sale: All descriptions, quotations, proposals, discard or otherwise dispose of any special tooling or other property in its
offers, acknowledgments, acceptances and sales of Seller’s products are sole discretion at any time.
subject to and shall be governed exclusively by the terms and conditions 8. Buyer’s Property: Any designs, tools, patterns, materials, drawings,
stated herein. Buyer’s acceptance of any offer to sell is limited to these terms confidential information or equipment furnished by Buyer, or any other
and conditions. Any terms or conditions in addition to, or inconsistent with items which become Buyer’s property, may be considered obsolete and
those stated herein, proposed by Buyer in any acceptance of an offer by may be destroyed by Seller after two (2) consecutive years have elapsed
Seller, are hereby objected to. No such additional, different or inconsistent without Buyer placing an order for the items which are manufactured using
terms and conditions shall become part of the contract between Buyer and such property. Seller shall not be responsible for any loss or damage to
Seller unless expressly accepted in writing by Seller. Seller’s acceptance such property while it is in Seller’s possession or control.
of any offer to purchase by Buyer is expressly conditional upon Buyer’s
9. Taxes: Unless otherwise indicated on the face hereof, all prices and
assent to all the terms and conditions stated herein, including any terms in
charges are exclusive of excise, sales, use, property, occupational or like
addition to, or inconsistent with those contained in Buyer’s offer. Acceptance
taxes which may be imposed by any taxing authority upon the manufacture,
of Seller’s products shall in all events constitute such assent. sale or delivery of the items sold hereunder. If any such taxes must be
2. Payment: Payment shall be made by Buyer net 30 days from the date of paid by Seller or if Seller is liable for the collection of such tax, the amount
delivery of the items purchased hereunder. Amounts not timely paid shall thereof shall be in addition to the amounts for the items sold. Buyer agrees
bear interest at the maximum rate permitted by law for each month or portion to pay all such taxes or to reimburse Seller therefore upon receipt of its
thereof that the Buyer is late in making payment. Any claims by Buyer for invoice. If Buyer claims exemption from any sales, use or other tax imposed
omissions or shortages in a shipment shall be waived unless Seller receives by any taxing authority, Buyer shall save Seller harmless from and against
notice thereof within 30 days after Buyer’s receipt of the shipment. any such tax, together with any interest or penalties thereon which may
3. Delivery: Unless otherwise provided on the face hereof, delivery shall be assessed if the items are held to be taxable.
be made F.O.B. Seller’s plant. Regardless of the method of delivery, 10. Indemnity For Infringement of Intellectual Property Rights: Seller
however, risk of loss shall pass to Buyer upon Seller’s delivery to a carrier. shall have no liability for infringement of any patents, trademarks, copyrights,
Any delivery dates shown are approximate only and Seller shall have no trade dress, trade secrets or similar rights except as provided in this Part 10.
liability for any delays in delivery. Seller will defend and indemnify Buyer against allegations of infringement
4. Warranty: Seller warrants that the items sold hereunder shall be free of U.S. patents, U.S. trademarks, copyrights, trade dress and trade secrets
from defects in material or workmanship for a period of 18 months from (hereinafter “Intellectual Property Rights”). Seller will defend at its expense
date of shipment from the Company. THIS WARRANTY COMPRISES and will pay the cost of any settlement or damages awarded in an action
THE SOLE AND ENTIRE WARRANTY PERTAINING TO ITEMS brought against Buyer based on an allegation that an item sold pursuant
PROVIDED HEREUNDER. SELLER MAKES NO OTHER WARRANTY, to this contract infringes the Intellectual Property Rights of a third party.
GUARANTEE, OR REPRESENTATION OF ANY KIND WHATSOEVER. Seller’s obligation to defend and indemnify Buyer is contingent on Buyer
ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO, notifying Seller within ten (10) days after Buyer becomes aware of such
MERCHANTABILITY AND FITNESS FOR PURPOSE, WHETHER allegations of infringement, and Seller having sole control over the defense
EXPRESS, IMPLIED, OR ARISING BY OPERATION OF LAW, TRADE of any allegations or actions including all negotiations for settlement or
USAGE, OR COURSE OF DEALING ARE HEREBY DISCLAIMED. compromise. If an item sold hereunder is subject to a claim that it infringes
the Intellectual Property Rights of a third party, Seller may, at its sole
NOTWITHSTANDINGTHE FOREGOING,THERE ARE NOWARRANTIES expense and option, procure for Buyer the right to continue using said
WHATSOEVER ON ITEMS BUILT OR ACQUIRED WHOLLY OR item, replace or modify said item so as to make it noninfringing, or offer to
PARTIALLY, TO BUYER’S DESIGN OR SPECIFICATIONS. accept return of said item and return the purchase price less a reasonable
5. Limitation of Remedy: SELLER’S LIABILITY ARISING FROM OR IN allowance for depreciation. Notwithstanding the foregoing, Seller shall
ANY WAY CONNECTED WITH THE ITEMS SOLD OR THIS CONTRACT have no liability for claims of infringement based on information provided
SHALL BE LIMITED EXCLUSIVELY TO REPAIR OR REPLACEMENT by Buyer, or directed to items delivered hereunder for which the designs
OF THE ITEMS SOLD OR REFUND OF THE PURCHASE PRICE PAID are specified in whole or part by Buyer, or infringements resulting from the
BY BUYER, AT SELLER’S SOLE OPTION. IN NO EVENT SHALL modification, combination or use in a system of any item sold hereunder.
SELLER BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR The foregoing provisions of this Part 10 shall constitute Seller’s sole and
SPECIAL DAMAGES OF ANY KIND OR NATURE WHATSOEVER, exclusive liability and Buyer’s sole and exclusive remedy for infringement
INCLUDING BUT NOT LIMITED TO LOST PROFITS ARISING FROM of Intellectual Property Rights.
OR IN ANY WAY CONNECTED WITH THIS AGREEMENT OR ITEMS If a claim is based on information provided by Buyer or if the design for an
SOLD HEREUNDER, WHETHER ALLEGED TO ARISE FROM BREACH item delivered hereunder is specified in whole or in part by Buyer, Buyer
OF CONTRACT, EXPRESS OR IMPLIED WARRANTY, OR IN TORT, shall defend and indemnify Seller for all costs, expenses or judgements
INCLUDING WITHOUT LIMITATION, NEGLIGENCE, FAILURETO WARN resulting from any claim that such item infringes any patent, trademark,
OR STRICT LIABILITY. copyright, trade dress, trade secret or any similar right.
6. Changes, Reschedules and Cancellations: Buyer may request to modify 11. Force Majeure: Seller does not assume the risk of and shall not be
the designs or specifications for the items sold hereunder as well as the liable for delay or failure to perform any of Seller’s obligations by reason
quantities and delivery dates thereof, or may request to cancel all or part of circumstances beyond the reasonable control of Seller (hereinafter
of this order, however, no such requested modification or cancellation shall “Events of Force Majeure”). Events of Force Majeure shall include without
become part of the contract between Buyer and Seller unless accepted by limitation, accidents, acts of God, strikes or labor disputes, acts, laws, rules
Seller in a written amendment to this Agreement. Acceptance of any such or regulations of any government or government agency, fires, floods, delays
requested modification or cancellation shall be at Seller’s discretion, and or failures in delivery of carriers or suppliers, shortages of materials and
shall be upon such terms and conditions as Seller may require. any other cause beyond Seller’s control.
7. Special Tooling: A tooling charge may be imposed for any special 12. Entire Agreement/Governing Law: The terms and conditions set
tooling, including without limitations, dies, fixtures, molds and patterns, forth herein, together with any amendments, modifications and any
acquired to manufacture items sold pursuant to this contract. Such special different terms or conditions expressly accepted by Seller in writing, shall
tooling shall be and remain Seller’s property notwithstanding payment constitute the entire Agreement concerning the items sold, and there are
of any charges by Buyer. In no event will Buyer acquire any interest in no oral or other representations or agreements which pertain thereto.
apparatus belonging to Seller which is utilized in the manufacture of the This Agreement shall be governed in all respects by the law of the State
items sold hereunder, even if such apparatus has been specially converted of Ohio. No actions arising out of sale of the items sold hereunder or this

N
or adapted for such manufacture and notwithstanding any charges paid Agreement may be brought by either party more than two (2) years after
by Buyer. Unless otherwise agreed, Seller shall have the right to alter, the cause of action accrues.
©®2008 Parker Hannifin Corporation Printed in U.S.A.
May, 2008

N10 Parker Hannifin Corporation

Pneumatic Division
Wadsworth, Ohio
www.parker.com/pneumatics