U61

USER
MANUAL Suitable for indoor flight

This product is suitable for users over 14 years old.

Stay away from the rotating propeller
Read the<important statement and safety guidelines >carefully.
 Ready Before Take Off
Drone preparation

Front (Prow)

Main frame

Propeller A Propeller B

Drone Cover
Housing

Propeller B Propeller A

Rear (Tail)

Camera
ON OFF
Power
Switch

Drone LED

Front (Prow) Rear (Tail)

2
 Charging Instruction
Battery power is insufficient in the original plant. It must be charged
saturated before it can be used.
Connect the original charging cable with the drone, and then connect other USB
charging port. The drone red LED keeps bright when charging and the light turns
green when fully charged. The drone power button should be
turned off when charging.

Drone battery ① ②
Original Charging Cable

USB adapter
(Not included)

Only use the original charging cable; suggest select Adapters with output current of 5V 2A.

Battery Installation

Installation:
Put the battery into the battery
compartment and push it into
position.

Battery buckle

Disassembly:
Press the battery button and pull the battery back.

3
 Transmitter Preparation

Phone Holder Jack

Photo Heading Hold Mode
Video Take Off / Landing/
Power-LED Emergency Stop

Left Stick Right Stick

Trimmer Speed switching
(Press Down) (Press Down)

Power Switch

Phone
(not include)

Notice: Taking photo and recording video

are available after connecting with
smart phone.

Battery installation

Open the battery cover of the remote

controller and place the same type of
battery with saturated capacity,
according to the '+-' electrode indication
Back
in the battery cell (Not include).

4×1.5V AA Battery

Battery cover
4
Mobile Phone Installation

Take out the phone holder

and insert into the transmitter.

Pull out upper lamp

of the holder and put the
phone into the holder,
then release the clamp,
and the phone will be fixed
on the holder. Please make
sure that the button on
phone is not clamped.

When take out the phone clip, you

need to press the clip buckle behind
the phone clip , so that the buckle
can be closed and removed easily.

Flight Operations
Mobile phone connect with Drone

Download and install APP: Flyingsee

This software is suitable for mobile phones
in the IOS and Android system. For detailed
operation, please check the system “HELP”
of APP.

5
 Transmitter connect with Drone

Frequency Pairing

Turn on the prower

on the transmitter, the
transmitter indicator
light will flash quickly.

Press down
Pull the left stick until bottom
and then release, the transmitter
power-LED will flash slowly, and
enter frequency pairing.

Turn on power switch of drone,

the indicator light becomes from
shiny to long bright which
indicating the drone is in the state
It must be placed on the horizontal ground. of successful opposite frequency.

Control stick operation

Left stick

Go up
Counterclockwise
turn

Go down

Clockwise turn

6
 Right stick

Forward
Fly to the left

Backward

Fly to the right

Take off

After the frequency pairing is successful, press the "take off/land" button, the
transmitter will sound "di", and the drone will automatically rises and flies at an
altitude of about 1.2 meters.

Landing
During the flight, press the "take off/land"
button, the transmitter will sound "di",
and the drone will land slowly until landing.
Don’t operate the left stick during landing,
otherwise the current command will
automatically fail.
Emergency Stop: During the flight, press
" take off/land" button for about 2 seconds,
the transmitter will sound "di.di..." and the
drone crashes directly.
Tip: Do not use the emergency stop function unless in emergency situation.

7
 Heading Hold Mode
The default setting is NOT Heading Hold Mode.
Heading Hold Mode means that the user can operate the aircraft without having
to distinguish directions. This mode is suitable for beginners, or when it is
difficult to distinguish the forward and backward direction of the drone.
① The Heading Hold Mode needs to ensure that the front of the drone is
consistent with the front of the controller, the controller does
not change the direction of the transmitter, and the drone is
always in front of the controller.
② When the front of the drone is not
consistent with the pilot's front, the
drone will lose control or be lost.
Start: Press the "Heading Hold Mode" button,
the transmitter will sound "didi" to enter
the Heading Hold Mode.
Off: Press again, the transmitter will sound
"dididi" to exit the Heading Hold Mode.

Front

Rear

8
 Speed mode switch
Medium speed default
Press down the right stick in the center button,
the transmitter will sound "di" to enter the Low
Speed Mode "L". Press down
Press down again, the transmitter will sound
"di.di" to enter the Medium Speed Mode "M".
Press down again, the transmitter will sound
"di.di.di" to enter the High Speed Mode "H".
Low speed: suitable for beginners to practice without wind.
Medium speed: suitable for skilled operatoroperating in light breeze.
High speed: suitable for professional operation in outdoor wind resistance.

Photos Video

Short press the "Photo" button once Long press "video" about 1 seconds
to take a picture. toenter the recording state,to repeat
When taking photo , the transmitter thisaction to stop recording and save
will sound “di”. video.
When taking videothe transmitter
will sound“di”sound a long rang.

Notes for Filming

The photos and videos are stored in the phone local gallery,you can display
in the phone directly.
App must be authorized to access the phone gallery, if not, then may be
unavailable to display the video and photos.
9
 Flying Trimmer

Forward / Backward Trimmer

During the flight, if the drone tilts forward,
Press down
press down the left stick in the center button,
and push the right stick backwards.
Otherwise push forwards.

Left and right turning trimmer

Press down During the flight, if the drone head rotates to
left,then press down the left stick in the
center button and push the left stick to right.
Otherwise push to left.

Left and right side flying trimmer

Press down During the flight, if the drone tilts to left, then
press down the left stick in the center button
and push the right stick to right to adjust.
Otherwise push to left.

Drone calibration (When abnormal flying)

After successful frequency alignment,

the right stick is pushed to the lower
right corner by 45°, and the drone LED
turns to keep bright after quick flashing,
indicating that the gyroscope has been
calibrated. Release the right stick.
Tips: When the drone is fiercely impacted or crashed, it may cause the gyro
can not recover and cause difficult control, if so, you can re-pairing &
re-calibrateand put the drone on the level surface.

10
 Unlocking/locking the motor
Push the left and right stick inward to the
45 degree angle simultaneously.
In standby, unlocked the motor and working.
In Working, locked the motor and stop rotating.

Altitude Hold Mode

Intelligent flight control system calculates the hovering position, more stable
control feature, makes it easier for beginners to control. Release the stick, the
drone will keep hovering automatically to enable single hand operation.
Note: If the propeller is deformed or damaged, Altitude Hold Mode will fail.
If the atmospheric pressure is instability or Typhoon weather, Altitude Hold Mode
can not work well.

Low Battery Alarm

Transmitter: When the transmitter in low battery, the transmitter will continues
to sound "di...di...di......" to remind the user to return home and
replace the batteries of the transmitter as soon as possible.
Drone: When the drone in low battery, the transmitter will continues to sound
"di.di.di......" to remind the user to return home.

Out of range alarm

When the drone is out of the remote control distance, the transmitter will
continues to sound “didi...didi...didi” to alarm the user to return the drone
immediately.

Stuck Protection

① When the propellers get stuck, then activate stuck protection function and
the motors stop running.
② Pull down the left stick to the lowest position and then go back to the
center, stuck protection will be released and the drone can fly again.

11
 Parts Replacement
Propeller Replacement
Disassembly: hold the propeller vertically and then pull the propeller out.
Installation: mount propeller aim the central shaft of the motor and press down.
There is different A and B remarks on the propeller. Be sure that the propellers are installed
to the correct motors, which remarked the Letters to identify on the motor holder, if not,
then the drone can not work normally.

Disassembly Installation
B

B
B Please make sure the
propeller are installed
correctly, otherwise
the drone cannot fly.
A

A A

Attention
① Switching sequence. At first, turn on the power of the transmitter, then turn
on the power of the drone. After the end, turn off the power of the drone
first, and then turn off the power of the transmitter.
② Improper operation caused the crash. It is necessary to check and confirm
the connection of the motorpropeller or battery of the drone and the
damage degree, so that the drone can fly again. If there is damaged, please
replace the new accessories or prone to accident.
12
 Parameter
Drone APP / Live View
Model U61 App Name Flyingsee
Weitht 63g (typical value) Image transmission 2.4GHz wifi
Maximum 7 minutes(calm) system
flight time Real time image 480 P@20 fps
WIFI Distance 30m (indoor and transmission
unobstructed) Operation System This software is
Operating 0°C to 40°C suitable for mobile
Temperature Range phones in the
Operating frequency 2.4GHz / 2.4G WiFi IOS 9.0 or later
Battery 3.7V500mAh and Android 4.4
Type of battery LiPo or later system,
Charging Time About 80 minutes
Camera
Charging 5°C to 40°C
Image resolution 640×480P
temperature range
Static Photography Single shoot
Mode
Transmitter Video Resolution 640×480P
Operating frequency 2.4GHz Image mode RGB
Maximum 50m Frame Rate 25
transmission distance (unobstructed) File System FAT 32
Operating 0°C to 40°C Image format JPEG
temperature Battery 4×1.5V AA Video format MP4, H.264
battery TF Card Unable
Operation 0°C to 40°C
Charger Temperature
Output 5V 2A

Tips: the above data are the test data of UDIRC toy lab, for reference only.

Li-Po Battery Disposal & Recycling

Wasted Lithium-Polymer batteries should not be placed
with household trash. Please contact local environmental
or waste agency or the supplier of your model or your
nearest Lithium-Polymer batteries recycling center.

13
 Troubleshooting Guide
No. Problem Problem Cause Solution
1. Low battery. 1. Replace the transmitter battery.
The 2. The battery positive pole and 2. Install the battery in accordance with
1 transmitter negative pole are in reverse order. the user manual.
indicator
light is off 3. Clean the dirt between the battery and
3. Poor Contact. the battery slice.
1. Indicator light is off. 1. The same as above 1.2.3.

2. There is interfering signal nearby. 2. Restart the drone and power on the
Fail to pair transmitter.
2 the drone
with 3. Mis-operation. 3. Operate the drone step by step in
transmitter accordance with the user manual.
4. The electronic component is damaged 4. To buy spare parts from local seller
for frequent crash. and replace damaged parts.
1. The propeller deformed seriously. 1. Replace the propeller.
The drone
is under- 2. Low battery. 2. Recharge the drone battery.
3 powered or
can not fly. 3. Incorrect installation of propeller. 3. Install the propeller in accordance
with the user manual .
1. The propeller deformed seriously. 1. Replace propeller.
The drone 2. The motor holder deformed. 2. Replace the motor holder.
could not
4 hover and 3. The gyro did not reset after violent 3. Put the drone on the flat ground for
tilts to crash. about 10s or restart the the drone to
one side. calibrate again.
4. The motor is damaged. 4. Replace motor.
1. Low battery. 1. Recharge the drone battery.
The drone
5 indicator 2. The battery is expired or over 2. Buy a new battery from local seller to
light is off. discharge protection. replace the battery or charge the battery
in accordance with the use manual.

Could not 1. There is interfering signal nearby. 1. Cut off the wire and re-connect.
6 see the
picture. 2. Damaged camera. 2. Buy a new camera box from local
seller to replace
Hard to 1. Practice and read the cellphone
7 control by 1. Not experienced enough. controlling instruction carefully.
cellphone.

14
FCC Note
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving a ntenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.

WARNING: Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to
operate the equipment.

15
The equipment may generate or use radio frequency energy. Changes
or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction
manual. Modifications not authorized by the manufacturer may void
user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.

MADE IN CHINA

Our company's products are improving all the time, design

and specifications are subject to change without notice.
Important
All the information in this manual has been carefully checked
Notice
to ensure accuracy, if any printing errors, our company
reserve the final interpretation right.

16