WASHING MACHINE

SERVICE MANUAL
CAUTION
READ THIS MANUAL CAREFULLY TO DIAGNOSE
PROBLEMS CORRECTLY BEFORE SERVICING THE UNIT.

MODEL : WT1801H*A /01

 SAFETY PRECAUTION!
IMPORTANT SAFETY NOTICE!
This service information is intended for individuals possessing adequate backgrounds of
electrical, electronic, and mechanical experience. Any attempt to repair this appliance may result
in personal injury or property damage. The manufacturer or seller can not be responsible for the
interpretation of this information, nor can it assume any liability in connection with its use.

WARNING: To reduce the risk of fire, electric shock, or personal injury when using this
appliance, follow basic precautions, including the following:
·Wear gloves when working. ·Disconnect this appliance from the power
Failure to do this can result in serious injury. supply before servicing. Turning the controls to
·The appliance is heavy. Two or more people are the off position does not disconnect this
required when moving the appliance. appliance from the power supply.
There is a risk of serious back injury or other injuries. Failure to do this can result in shock.
·Certain internal parts are intentionally not ·Reconnect all grounded devices after servicing.
grounded and may present a risk of electric Failure to do this can result in shock.
shock only during servicing. Service personnel -
Do not contact the following parts while the
appliance is energized: Pump bracket, rotor, and
heater.

CONTENTS
1. Specifications ............................................ 3 4-5. Troubleshooting Summary................. 31
2. Installation Instructions 4-6. PCB Picture ...................................... 32
2-1. How to Adjust Level ............................ 4 4-7. Troubleshooting with Error Code....... 33
2-2. Connecting Water Supply Hose ......... 6 4-8. Other Troubleshooting....................... 40
2-3. Connect the Drain Hose ..................... 7 5. Component Testing Information................. 42
3. Operating Instructions 5-1. Filter Assembly (Line Filter)............... 42
3-1. Identification of Parts ......................... 8 5-2. Door Lock Switch Assembly............... 43
3-2. Before Starting to Wash ..................... 9 5-3. Stator Assembly................................. 45
3-3. Function of Each BUTTON ............. 16 5-4. Pump Motor Assembly....................... 46
3-4. Washing Programs .......................... 18 5-5. Inlet Valve Assembly.......................... 47
3-5. Care and Maintenance ..................... 19 5-6. Thermistor Assembly.......................... 48
4. Service Information 6. Exploded View ......................................... 51
4-1. Disassembly Instruction ................... 21 7. Replacement Part List ............................. 55
4-2. Wiring Diagram ................................ 28
4-3. Test Running Without Water ............ 29
4-4. Troubleshooting By Common
Washing Problems .............................30

2
1. SPECIFICATIONS

Model WT1801H*A /01

Electrical 120 VAC@60 Hz.

Inner Tub Stainless

Inlet Water Pressure 20 ~ 120 psi(138 ~ 827 kPa)

Rating of Fuse 120V/60Hz

Spin Speed 1100±50 rpm

Weight 137.3 lbs. (62.3 kg)

Normal, Heavy Duty, Bulky, Bright Whites™, Sanitary,

Cycles Allergiene™ , Perm.Press, Towels, Wool, Delicates, Speed
Wash, Tub Clean

Time Delay 1 – 19 Hr

Lid Interlock Switch Magnet Sensor

Control Lock Yes

Softener Dispenser Yes

Detergent Dispenser Yes

Bleach Inlet Yes

Auto Power Off Yes

Smart Rinse™with Jet Yes
Spray
Heater Yes

3
2. INSTALLATION INSTRUCTIONS
2-1. HOW TO ADJUST LEVEL Raise Lower

Installation area Checking level

1 • Install the washer on a firm, flat
surface.
3 • Open
 the lid, check if the washer is
correctly leveled by looking down
• If the washer is installed on an from the top. If the tub is not
unsuitable floor, it could make centered in the opening, then the
considerable noise and vibrate. washer is not level.

Raise
Raise Lower
Lower

Set Leveling feet Checking slope

2 •A
 djust the leveling feet, Turn clockwise
to raise the washer or
4 • If installation surface is tilted, the
washer will vibrate. Do not install
CAUTIONcounterclockwise to lower it. on a sloping floor.

Raise Lower

No shims. It would be dangerous. If the

floor is that far from being level, it is a floor
problem and not a washer problem.

CAUTION
CAUTION
•T  he ventilating openings in the base area must not be obstructed by carpeting.
• Install the washing machine on a level and firm surface. There should be no more than 1° of variation.
•W  ooden floors may need reinforcing to prevent the normal vibration which occurs
with an unbalanced load.
•D  o not install the washer on an inclined floor.
Improper installation of the washer may cause noise and malfunctioning.

4
 Horizontal setting Distance between the drain hose
5 • If the washer is not level, adjust the
leveling feet. Turn clockwise to raise,
7 and the wall
•D
 istance between the drain hose and
counterclockwise to lower.
the wall should be more than 4 inches
(10 cm,) and the distance between any
side to side
other part and the wall should be more
than 1 inches (2.5 cm.)
front to back

40 3/ 8”
(102.6 cm)

Lower Raise

1” 27” 1”

Confirming level (2.5cm) (2.5cm)

6
(68.6 cm)

•P
 lace the washer in original position, 32 ”
(81.1 cm)
confirming the level. 28 3 / 8”
(72.1 cm)

3 1 / 2”
(9 cm)

55 3/ 8”
(140.6 cm)
(with open lid)

26 3 /4”
(68 cm)

Do not install the washer in the following places.

• Where the washer is exposed to direct sunlight.

• Near a heater or heating appliance.
• Where the washer is exposed to freezing temperatures.
• In damp environments such as bathrooms or harmful environments.

5
2-2. CONNECTING WATER SUPPLY HOSE
Before connecting the water supply hose to the water tap, check the hose type and then choose the
correct instruction here below.

Screw Type

1 Be sure there is a gasket in both ends of the hose.

Push the water supply hose up so that the rubber packing
Water tap
within the hose can adhere completely to the tap.
Rubber Seal
Water Supply Hose

2 Connect the water supply hose to the tap.

Run a couple of gallons of water through the hoses into the drain or a
bucket to flush any particulate or contaminate.

3 Check water leakage.

After connecting the hose, open the tap to check for
any water leakage.

Connecting Water Supply Hose to the Machine

• Be sure there is a gasket in the end of the hose.

• Connect the hose to the appropriate inlet vale

(hot or cold) of the washing machine and tighten if
firmly.

• Turn on the water and check for leacks.

• Always install new hoses with a new washing

machine Do not re-use old hoses.

• Relplace the hoses every five years.

6
 2-3. CONNECT THE DRAIN HOSE

• Insert the end of the drain hose into the drain.

• If the drain is large enough for the flange on the hose to fit inside, then do not insert the flange more than 1-2 inches
into the drain.
• Check that the drain hose is hungup over the edge of the laundry tub.

35"~47" (0.9~1.2m)
• Do not use an extension hose.

35"~47" (0.9~1.2m)
35"~47" (0.9~1.2m)
35"~47" (0.9~1.2m)
Cable Tie
Cable Tie

NOTE : • T
 he drain hose should always be properly secured to the drain or standpipe. Failure to secure
the drain hose properly can result in flooding and property damage.
• The end of the drain hose should be placed 39" (99 cm) above the floor.
• The drain must be installed in accordance with any applicable local codes and regulations.
• Make sure that the water lines are not stretched, pinched, crushed, or kinked.
•D o not insert the drain hose more than 12” (30 cm) into the drain pipe to avoid siphoning and
odor build-up.

WARNING:
• The washer should never be installed or stored in a location subject to freezing temperatures. If the
washer was exposed to freezing temperatures prior to installation, allow it to stand at room
temperature for several hours before use. Damage to the water lines and internal mechanisms of
NG: the washer can result.
• Water supply pressure must be between 20 ~ 120 psi(138 ~ 827 kPa) If the water supply pressure
is more than 120 psi, a pressure reducing valve must be installed. If you have uncontrolled water
temperature and pressure you should fit a temperature and pressure relief valve to ensure that
water temperature and water pressure remain within the safe limits. Consult a plumber or electrician
if you are unable to adjust water temperature and or pressure. Failure to do so can result in damage
to the machine.
• Plug the power cord of washer into a properly grounded outlet. Failure to do this can result in shock
or serious injury.

7
3. OPERATING INSTRUCTION
3-1. IDENTIFICATION OF PARTS

COLD WATER SUPPLY

HOSE
HOT WATER SUPPLY
DOOR HOSE
Make sure the water
does not leak.

HARDENED GLASS

Powder detergent Smart Rinse with

Box for delayed Jet Spray
washing/softener additves box This washer is designed to
save rinse water by using a
INLET HOLE FOR jet spray rinse system in the
BLEACH Normal/Casual and Heavy
TUB Duty cycles.

POWER PLUG
If the supply cord is
damaged, it must be
replaced by the
manufacturer or its service
agents or similarly
qualified person in order
to avoid a hazard.
DRAIN HOSE
WASHING WING Be sure the drain hose
(unique with lnner Tub) is properly installed on
the drain before
operating the washer.

LEVELLING LEGS
Use to level the washing
machine for correct balance
spin operation.

8
3-2. BEFORE STARTING TO WASH

Care Labels
• Look for a care label on your clothes.
This will tell you about the fabric content of your garment and how it should be washed.
Sort clothes into loads that can be washed with the same wash cycle, water temperature,
and spin speed.

Sorting
To get the best results, different fabrics need to be washed in different ways.
• SOIL (Heavy, Normal, Light) Separate clothes according to the type and amount of soil.
• COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics.
• LINT (Lint producers, Collectors) Separate lint producers and lint collectors.
Lint Producers Terry cloth, Chenille, Towels, Diapers
Lint Collectors Synthetics, Corduroy, Permanent Press, Socks

Check before Loading

• Check all pockets to make sure that they are empty. Things such as nails, hairclips, matches,
pens, coins, and keys can damage both your washer and your clothes.
• Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
• Pretreat any dirt and stains.
• Make sure the clothes are washable in water.
• Check the washing instructions.
• Remove any paper or tissue in the pockets. WIRE

• Be sure the wire supports in undergarments are secure and will not become loose in the washer.

Pretreatment on stains or heavy soil

• Pretreat shirt collars and cuffs with a pre-wash product or liquid detergent when placing them in the washer.
Before washing treat special stains with bar soaps, liquid detergent, or a paste of water and powdered detergent.
• Use a pretreat soil and stain remover.
Treat stains AS SOON AS POSSIBLE. The longer they are left, the harder they are to remove.
(For more detail refer to page 14-15)

Loading
Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).
Load Size
The WATER LEVEL should just cover the clothes. Adjust the load size
accordingly. Loosely load clothes no higher than the top row of holes in the
washer tub. To add items after washer has started, press the START button and
submerge additional items. Close the lid and press the Start button again to restart.
※ Do not wash waterproofed fabrics (such as skiing outfits, diapers, or nappy
auto seat covers.)
Light and Large-sized clothing
Clothes like downs and woolens are lightweight, large, and float easily. Use a nylon net and
wash them in a small amount of water. If the laundry floats during the wash cycle, it may
become damaged. Use dissolved detergent to prevent the detergent from clumping.
※ Do not wash water-proof textilles (Skiing outfit, baby diaper, nappy automobile seat covers.)
Long laundry items
Use nylon bag nets for long, delicate items. For laundry with long strings or long length, a bag will prevent
tangling during washing. Fasten zippers, hooks, and strings to make sure that these items don't snag on
other clothes.
※ The nylon net bag can be purchased locally.
9
1) Using Water

Water Temperature

• The machine sets the appropriate temperature automatically according to the wash program .
You can override the preset selection by pressing the water temperature icon. Touch the arrow buttons up or
down until your desired temperature setting is displayed.
• The temperature of the water impacts the effectiveness of all laundry additives and, therefore, the cleaning results.
• We recommend temperatures of:
- HOT 120°F (120-140°F) White items, diapers, underclothing and heavily soiled, colorfast items.
- WARM 90°F (85-105°F) Most items
- COLD 66°F (65-75°F) Only very bright colors with light soil.
• When washing in COLD water additional steps may be needed:
- Adjust detergent amount and pre-dissolve detergent in WARM water
- Pretreat spots and stains
- Soak heavily soiled items
- Use appropriate bleach

* Temperature below 18°C (65°F) will not activate laundry additives and may cause lint, residue, poor cleaning, etc.
In addition, detergent manufactures and care labels define COLD water as 26~29°C (80-85°F).
If the temperature of the water in the tub is too cold for your hands, the detergent will not activate and clean
effectively.

Note
If iron is present in the water, the clothes may become an all-over yellow or they may be stained with brown or
orange spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be
necessary for severe cases.

10
2) Using Detergent
Detergent

Follow the detergent package directions. Using too little detergent is a common cause of laundry problems.
Use more detergent if you have hard water, large loads, greasy or oily soils or lower water temperature.

Choosing the Right Detergent

Your washing machine is designed for use with only High-Efficiency (HE) detergents. HE detergents are
formulated specifically for HE machines and contain suds-reducing agents. Always look for the HE symbol when
purchasing detergent. HE detergents produce fewer suds, dissolve more efficiently to improve washing and
rinsing performance, and help to keep the interior of your washer clean. Using a regular detergent will cause
unsatisfactory performance, oversudsing, machine build-up, and could damage the machine.

Using the Liquid Bleach Dispenser

The bleach dispenser automatically dilutes and dispenses

liquid chlorine bleach at the proper time in the wash cycle.
1. Check clothing care labels for special instructions.
2. Measure liquid bleach carefully, following instructions on the
bottle.
• Never pour undiluted liquid chlorine bleach directly onto clothes
or into the wash basket.
• Do not pour powdered bleach into bleach dispenser.
• Avoid overfilling or splashing when adding bleach to the
dispenser. The maximum capacity of the bleach dispenser is
one cup of bleach per wash cycle. Overfilling could result in
premature dispensing of bleach.
Do NOT add more bleach than is required for your particular load.
3. B efore starting the washer, pour measured amount of liquid bleach
directly into bleach dispenser. If you prefer to use powdered
bleach, add it into the wash basket directly before adding clothes.

WARNING Do NOT mix chlorine bleach with ammonia or acids, such as vinegar or rust / scale remover.
Mixing chemicals like these can produce irritating and toxic fumes. Put the manufacturer’s recommended amount of
undiluted liquid chlorine bleach into the bleach dispenser. During the final portion of the wash cycle, two sequential flushes
of the dispenser put all the bleach into the wash load and completely flush the dispenser to eliminate the carryover of
bleach to a subsequent load. Any liquid remaining in the bleach dispenser at the end of the cycle is water, not bleach. To
prevent unintentional self-siphoning of the bleach, never fill the dispenser higher than the maximum fill level marked on
the dispenser. When adding bleach to the dispenser, be careful to avoid spilling it into the laundry load or leaving droplets
of bleach around the dispenser. These things will damage your laundry items.

Main Wash Main Wash

Powder Detergent Liquid Detergent
Compartment Compartment

Liquid Fabric
Softener
Compartment

11
Using the Dispenser Drawer

ABOUT THE DISPENSER Main Wash Main Wash

Powder Detergent Liquid Detergent
The automatic dispenser consists of two Compartment Compartment
compartments which hold:
• Liquid fabric softener. Liquid Fabric
• Liquid or powdered detergent. Softener
All laundry products can be added at once in their respective Compartment
dispenser compartments. They will be dispensed at the
appropriate time for the most effective cleaning.
After adding the laundry products to the dispenser,
close the dispenser drawer.
Close the dispenser drawer gently to avoid spilling or starting the
siphoning action.

To add detergent, bleach, and fabric softener

to the automatic dispenser:
❶ Open the dispenser drawer.
❷ Load the laundry products into the appropriate compartments.
❸ Close the lid slowly and smoothly to avoid spilling, splashing, or
premature dispensing of the contents.

NOTE: It is normal for a small amount of water to remain in the

dispenser compartments at the end of the cycle.
NOTE: Do not use powdered or liquid bleach in the dispenser drawer.

12
 Adding Detergent

Add measured detergent to the detergent compartment of the

dispenser drawer.

• Do not exceed the maximum fill line.

Detergent is flushed through the dispenser at the beginning of

the wash cycle. Either powdered or liquid detergent can be
used, but the drawer insert must be removed to use powder.

Detergent usage may need to be adjusted for water

temperature, water hardness, size, and soil level of the load.
Avoid using too much detergent in your washer, as it can lead
to oversudsing and detergent residue being left on the clothes.

Adding Fabric Softener

Pour the recommended amount of liquid fabric

softener into the left-hand compartment. Use only liquid fabric
softener.

Dilute with water to the maximum fill line.

• Do not exceed the maximum fill line.

Overfilling can cause early dispensing of the fabric softener,

which could stain clothes.

NOTE: Do not pour fabric softener directly on the wash load.
It may stain the clothes.
If you use an ultra-thick fabric softener, you might
want to dilute it with water so it dispenses easily.

Adding Wash Boost Additives

The wash boost dispenser may be used to clean heavily soiled

or stained garments more efficiently.

If desired, place the additives for the wash boost setting in the
right-hand compartment. Use only liquid additives.

• Do not exceed the maximum fill line to avoid detergent buildup
In clothing and the washer

Overfilling can cause early dispensing of presoak additives,

which could result in damaged clothes.

NOTE : Do not pour additives directly on the wash load. It may stain the clothes.

13
3) Special Guide for Stain Removal
WARNING
Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid, or products
containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.
T
 o reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:
• Read and comply with all instructions on stain removal products.
• Keep stain removal products in their original labeled containers and out of children's reach.
• Thoroughly wash any utensil used.
• Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
•N ever wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents, or
other flammable or explosive substances because they give off vapors that could ignite or explode.
• Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.

For successful stain removal:

• Remove stains promptly.
• Determine the kind of stain, then follow the recommended treatment in the stain removal
chart below.
• To pretreat stains, use a prewash product, liquid detergent, or a paste made from
powdered detergent and water.
• Use COLD water on unknown stains because HOT water can set stains.
• Check care label instructions for treatments to avoid on specific fabrics.
• Check for colorfastness by testing stain remover on an inside seam.
• Rinse and wash items after stain removal.

14
 Stain Removal
STAIN TREATMENT
Adhesive tape, chewing Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with
gum, rubber cement prewash stain remover or nonflammable dry cleaning fluid.
Baby formula, dairy Use product containing enzymes to pretreat or soak stains.
products, egg
Beverages (coffee, tea, soda, Pretreat stain. Wash using COLD water and bleach safe for fabric.
juice, alcoholic beverages)
Blood Soak the item in a bowl of COLD water for at least 30 minutes. Then launder as usual.
Remove all surface wax. Put the garment in the freezer for a couple of hours, then
Candle wax, crayon remove and break away as much wax as possible. Try a commercial removal product
like Goo-Gone, Goop, or Go-Jo cleaner for the remaining wax stains. DO NOT
ATTEMPT TO REMOVE WITH HEAT!
Chocolate Pretreat or soak in WARM water using product containing enzymes. Wash using bleach
safe for fabric.
Collar or cuff soil, cosmetics Pretreat with prewash stain remover or rub with bar soap.
Dye transfer on white fabric Use packaged color remover. Wash using bleach safe for fabric.
Grass Pretreat or soak in WARM water using product containing enzymes. Wash using bleach
safe for fabric.
Grease, oil, tar (butter, fats, Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For
salad, dressing, cooking heavy stains and tar, apply nonflammable dry cleaning fluid to back of stain. Replace
oils, car grease, motor oils) towels under stain frequently. Rinse throughly. Wash using hottest water safe for fabric.
Ink Some inks may be impossible to remove. Washing may set some inks. Use prewash
stain remover, denatured alcohol, or nonflammable dry cleaning fluid.
Mildew, scorch Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water
before washing. Badly mildewed fabrics may be permanently damaged.
Mud Brush off dry mud. Pretreat or soak with product containing enzymes.
Mustard, tomato Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Nail polish May be impossible to remove. Place stain face down on paper towels. Apply nail polish
remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
Paint, varnish WATER BASED Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it
cannot be removed,
OIL BASED AND VARNISH Use solvent recommended on can label. Rinse throughly
before washing.
Rust, brown or yellow For spots, use rust remover safe for fabric. For discoloration of an entire load, use
discoloration phosphate detergent and nonchlorine bleach. Do not use chlorine bleach because it
may intensify discoloration.
Shoe polish LIQUID Pretreat with a paste of powdered detergent and water. Apply paste and
scrape residue from fabric. Pretreat with prewash stain remover or nonflammable dry
cleaning fluid. Rub detergent into dampened area. Wash using bleach safe for fabric.

15
3-3. FUNCTION OF EACH BUTTON

Load Sensing
·It operates in all cycles.
·During being detected by the sensor, the
LOADSENSING LED flashes.
·It automatically sensing the size of the load.
·During this step, the washing machine selects
optimized washing algorithm.

Custom Program
BUTTON
·This button
allows
you to store a
customized
wash
cycle for
future use .

Delay Wash (Selection) Fabric Wash / Temp.

BUTTON Softener
·Delayed finishing time. ·Causes the ·Select to select Wash
·The time increases when the dispensing of Temperature.
button is pushed. fabric softener ·Pressing the button allows The
·The following settings are in the final selection of Tap cold
indicated as the button is rinse cycle. ▶Cold ▶WARM ▶ EXTRA
pushed 1 ▶ 2 ▶3 ▶ 4 ▶ ... HOT respectively. Default
19▶ setting is Warm.
Reservation off ▶ 1 ...
·To cancel delay time, turn the
power switch off or push DELAY
WASH button until off.

Note
The time shown on the display is the estimated cycle time. If the sensors and microprocessor elect to
make changes during the cycle, the display will be adjusted accordingly.

16
 POWER

·Power on.
·Push again, power goes off
·Power goes off automatically after the wash is
finished.
s an ·After turning the power on, the unit will
automatically turn off if nothing is selected.

START/ PAUSE BUTTON

·Use to start or pause the wash
cycle.
Changes while be made to the
wash settings while the machine is
paused.
·Repeats start and pause by
pushing the button.

Spin Speed Soil Level

·Spin speed can ·Allows a selection to be make for the
be selected strength of the wash action.
from No Spin to ·Power option selections light up in
Extra high. sequence as follows Normal ▶ Heavy ▶
Default is High. Light ▶ Normal as the button is pushed.
This can be selected for any program.
·Adjustment can be made while washing.
·Default SOIL LEVEL is Normal.

17
3-4. WASHING PROGRAMS.
CYCLE GUIDE
The cycle guide below shows the default settings, available options and
= Available Option
recommended fabric types for each cycle. Allowable modifier adjust-
= Default Setting
ments are shown below the default setting for each cycle.

Cycle Fabric or Wash Spin Soil Turbo Soak Stain Cold Extra Water Fabric
Steam Wash™
Load Type Temp. Speed Level Care™ Wash™ Rinse Plus Softener
Warm High Normal
Cotton, linen, Extra Hot
towels, shirts, Extra High
Normal sheets, jeans, Hot Heavy
Medium
mixed loads Cold Light
No Spin
Tap Cold
Warm High Heavy
Extra High
Heavy Duty Heavy soiled cot- Hot Medium Normal
ton fabrics Cold
Low Light
Tap Cold
No Spin
Warm High Normal
Large items such Hot Extra High
as blankets and Medium Heavy
comforters Cold
Low Light
Tap Cold
Bulky No Spin
* Use the Bulky cycle for items such as pillows, comforters, pet bedding and other articles which have dif-
ficultly absorbing water. DO NOT WASH EXCESSIVELY LARGE ITEMS. If large/bulky items do not fit easily
into the tub, there may not be enough room for them to move during washing. Keep like items together; do
not mix large bulky items with smaller clothing items. Failure to follow these instructions may result in dam-
age to the clothing or to the washer.
Hot Medium Heavy
Extra High
Bright
White fabrics High Normal
Whites™ Warm
Low Light
No Spin
Extra Hot High Heavy
Heavily soiled
underwear, work Extra High
Sanitary clothes, diapers, Medium Light
etc. (less than 11 Low Normal
lbs.) No Spin
Extra Hot High Heavy
Cotton, under-
wear, pillow cov- Extra High
Allergiene™ ers, bed sheets, Medium Normal
baby wear. (less Low Light
than 12 lbs.) No Spin

18
CYCLE GUIDE
The cycle guide below shows the default settings, available options and
= Available Option
recommended fabric types for each cycle. Allowable modifier adjust-
= Default Setting
ments are shown below the default setting for each cycle.

Cycle Fabric or Wash Spin Soil Turbo Stain Cold Extra Water Fabric
Load Type Temp. Speed Level Steam Wash™ Soak Care™ Wash™ Rinse Plus Softener
Dress shirts/pants, Warm Medium Normal
Perm.Press/ wrinklefree cloth- High
ing, poly/cotton Cold Heavy
Casual blend clothing, Low
Tap Cold Light
table- cloths No Spin
Warm High Normal
Towels, shirts, Extra High
Hot
Towels sheets, jeans, Medium Heavy
mixed loads Cold
Low Light
Tap Cold
No Spin
Warm Low Light
Item labeled
Wool machine washable Cold Medium Heavy
wool (less than 8
lbs.) Tap Cold No Spin Light

Tap Cold Low Light

Dress shirts/
blouses, nylons, High
Delicates sheer or lacy gar- Warm Heavy
ments (less than Medium
Cold Normal
8 lbs.) No Spin
Warm High Light
Extra High
Speed Wash Lightly soiled and
small loads Cold Medium Heavy
Tap Cold Low Normal
No Spin
Hot High Light

Tub Clean Refer to page 27.

NOTE:
To protect your garments, not every wash/rinse temperature, spin speed, soil level, or option is available with
every cycle. A chime will sound and the LED will not light if the selection is not allowed.
*When a cycle is selected, the default time for that cycle is displayed. This time will change as modifiers or
options are selected. Once the START/PAUSE button is pressed, the washer will measure the size of the load.
The estimated time may change once the load size has been measured. The washer automatically adjusts the
wash time for the amount of laundry, water pressure, water and other operating conditions.

19
3-5. CARE AND MAINTENANCE

When There Is The Possibility Of Freezing Temperatures

• Close the water taps and remove the water supply hoses.
• Remove the water which remains in the water supply.
• Lower the drain hose and drain the water in the sump and the drain hose by running a spin cycle.

If Frozen
• Remove the water supply hose and immerse it in HOT water. (40° C or 104° F).
• Pour approximately 2 liters (½ gallon ) of HOT water (40° C or 104° F) into the sump and allow it to stand for at
least 10 minutes.
• Connect the water supply hose to the water tap. Run an Express Wash cycle to confirm that the machine fills,
drains, and operates properly.
Wash Inner-Tub Leave the lid open after washing to allow moisture to evaporate. If you
want to clean the inner-tub use a clean soft cloth dampened with liquid
detergent, then rinse. (Do not use harsh or gritty cleaners.)
Inlet Hoses Hoses connecting washer to faucet should be replaced every 5 years.
Exterior Immediately wipe off any spills. Wipe with damp cloth. Avoid hitting surface with sharp
objects.
Long Vacations Be sure water supply is shut off at faucets. Drain all water from hoses if weather will be
below freezing.

Cleaning The Inside Of Your Washer

If you use fabric softener or do regular COLD water washing, it is very important that you
clean the inside of your washer occasionally as described below.
• Fill your washer with HOT water.
• Add 1 cup of bleach.
• Let it operate for several minutes.
• Stop the washer, open the lid, and leave it to soak overnight.
• After soaking, drain the washer and run it through a normal cycle.

Products That Might Damage Your Washing Machine

• Concentrated bleaches and diaper sanitizer will cause damage to the paintwork and components of
your washer.
• Hydrocarbon solvents, i.e. gasoline, kerosene, paint thinners, and lacquer thinners, etc. can dissolve plastic
and blister paint.
(Be careful when washing garments stained with these solvents as they are flammable; DO NOT put
them in washer or dryer.)
• Some pretreatment sprays or liquids can damage your washer’s control panel.
• Use of dyes in your washer may cause staining of the plastic components. The dye will not damage
the machine but we suggest you thoroughly clean your washer afterwards. We do not recommend
the use of dye strippers in your washer.
• Do not use your washer lid as a work surface.

20
4. SERVICE INFORMATION
4-1. DISASSEMBLY INSTRUCTION
▶B e sure to unplug the power to repair and replace
electric parts.

ESD (ElectroStatic DIscharge) WARNING

Be sure to follow proper ESD and grounding
precautions for diagnosis and repair. If this is not
possible, touch the ground wire on a regular basis to
remove any static charge built up on your person.

1) Remove front panel and main PCB

assembly

①R  emove 2 cap and 2 screw attaching the front panel.

② Push the front panel left and pull the front panel
forward.

③ Disassemble the protective cover.

④ Disconnect the leads from controller.

21
 2) Disassembly of the Noise Filter,
Power Cord, Inlet Valve, Pressure
Switch, and Dispenser Housing.

① Remove 2 screw attaching the panel on the back.

② Disassemble the rear panel.

Noise Filter and Inlet Valve

Power Cord
① Disconnect
 the
① Remove the two leads from the inlet
screws attaching the valve and remove
noise filter. three screws.
② Disconnect both ② Remove the hoses
connectors in the and output pipes
noise filter. from the input
Remove the power valve.
cord from the noise ③ Remove the inlet
filter. valve.

Pressure Switch Dispenser

Housing
① Disconnect the leads
from pressure switch ① Remove
 the hoses
and detatch the and output pipes
pressure switch from from the input
the machine. valve.
② Disconnect the ② Disassemble the
pressure tube from connector pipe and
the pressure switch. the dispenser
housing.
22
3) Disassembly of Top Cover and Lid
① Remove 2screws attaching the back side of top
cover.

②R
 emove 2screws that assembly the top cover with
the front panel.

③ Lift the top cover at the front of the washer.

④ Remove the hinge cover and 6 hinge screw.

⑤P
 ull the hinge to the left and right and Remove the
hinge.

23
 Inner Tub Cap
Tub Cover Hub Fixing Nut

Outer Tub
Inner Tub

Pulsator Cap

Pulsator Shaft
Screw Bearing Housing ASM
Rotor
Rotor Nut Stator

Pulsator

Inner
Tub Cap Hub Attachment Nut

4) Disassembly of Tub Cover and Pulsator

① Remove
 8 screws and take off the tub cover.
② Remove the pulsator cap.
③ Remove the pulsator screws.
④ Remove the pulsator washer.

5) Assemble the service tool (38 mm wrench)

6) Remove the hub attachment nut. (38 mm)

① Hit the bar using the hammer. ② Disconnect hub nut and disassemble the inner tub.

24
7) Disassembly of the Back Cover and
Drain Pump
① Remove the screws that attach the back cover and
take it off.
② Disconnect the leads and the drain hose from the
drain pump.
③ Remove the pump attachment screws and the lead
connector. Take the pump assembly out of the
washer.

8) Disassembly of Damper Assembly

① R
 emove the top cover and the back cover of the
washing machine.
② Pull out the hinge which connect the horizontal
damper with outer tub.( To disassembly the
horizontal damper, take the horizontal damper out
of the holder.)

③ A
 s shown in the drawing, lift the damper assembly
and remove it along with the outer tub assembly.
④ Damper assembly shall not be disassembled.
Replace damper as assembly.
9) Disassembly of Rotor and Stator
① Use a wrench (M24) to remove the nut that
connects the rotor to the shaft.
(The torque should be 200 kgf/cm or 88 foot-
pounds.)

② Remove the rotor by pulling it straight off the

splined shaft.

25
 ③ Remove the screws that secure the water guide.

④D
 isconnect the stator connection before removing
the stator in the subsequent step.

⑤ Remove the six screws securing the rotor.

⑥ Check the position of the snap ring, being sure it
faces the rotor and stator.

⑦ To keep from dropping the stator, loosen the six

bolts almost all the way; then hold the stator in one
hand while removing the bolts with the other.
⑧ Be careful during removal and replacement to
avoid cutting, nicking, or pinching any of the wires.
This could cause a short or electrical noise in the
machine.

26
 ⑨ Remove four screws to release the tub bracket.

⑩R
 emove 17 screws to release the bearing housing.
Pull the housing away from the tub, but do not pry it
with a screwdriver to avoid damage.

Bearing Housing

10) Disassembly of Door Lock Switch

① Remove the two door lock attachment screws.
② Remove the door switch and remove the attachment tube.

27
4-2. WIRING DIAGRAM

Motor

28
4-3. TEST RUNNING WITHOUT WATER
1) SAFETY CAUTION
•T  he main power board assembly has exposed live 120 VAC and live DC voltages. Use care when disconnecting
connectors during troubleshooting and testing. (Wear electrostatic discharge gloves when handling the board.
• Unplug the power when handling the board assembly. (Wear electrostatic discharge gloves when handling the
board. Store the board in an ESD [ElectroStatic Discharge] plastic bag.)

2) SERVICE MODE
The washer must be empty and the controls must be plugged in and turned off.

• Press and hold the SPIN SPEED and Water Plus button: then press the POWER button. The buzzer will sound
twice.
• Press the Start/Pause button to advane to the subsequent test mode step.

Number of times the

START/PAUSE Check Point Display Status
button is pressed
None Main program version t1 and main program version

1 time Display program version t2 and display program version

2 time None t3

3 time Inlet valve for detergent turns on.(Cold Water) A and water level frequency(268 ~ 233)

4 time Inlet valve for detergent turns on.(Hot Water) b and water level frequency(268 ~ 233)

5 time Inlet valve for softener turns on.(Cold Water) C and water level frequency(268 ~ 233)

6 time Inlet valve for jet spray turns on.(Cold Water) d and water level frequency(268 ~ 233)

7 time Inlet valve for bleach turns on.(Cold Water) E and water level frequency(268 ~ 233)

8 time Heater check (on heater model) t4 and the coefficient of flood sensing

9 time Heater check (on heater model) t5 and alpha RPM

10 time Drain pump and agitate (pulsator) check t6 and water level frequency(268 ~ 233)

11 time Load sensing Check t7 and the coefficient of load sensing

12 time Agitate (tub) check t8 and RPM

13 time Spin Check t9 and RPM

Off
14 time • Unlocks the door None
• Turns off all LED

29
4-4. TROUBLESHOOTING BY COMMON WASHING PROBLEMS
Many washing problems involve poor soil and stain removal, residues of lint and scum, and fabric damage. For
satisfactory washing results, follow these instructions.
Use ONLY powdered or liquid HE (High Effificiency) detergents. Do NOT use flakes scraped from a soap
cake or bar, flakes, soap ribbons (available in some markets,) detergent tablets, plastic pouches, magic
laundry balls, or anything other than powdered or liquid HE detergent products. Do not use soap of any kind.
Do not use other types of detergent or soap products, such as hand soap, dishwashng liquid, or any others.
WASHING PROBLEM
Problems Possible Causes Solutions and Preventive Measures

Poor soil ·Insufficient detergent ·Use correct amount of detergent for load size, amount of soil and
removal ·Wash water temperature too low water hardness.
·Incorrect wash cycle ·Use WARM or HOT water for normal soil. Different water
·Laundry missorted temperature may be required according to soil type. (refer to page 10)
·Stains not properly pretreated ·Reduce load size.
·Wash with heavy or soak & heavy wash cycle for heavy soiled
laundry.
·Separate heavily soiled items from lightly soiled ones.
·Pretreat stain and heavy soil according to directions shown on
page 15.

Blue Stains ·Undiluted fabric softener ·Pretreat the stain with detergent or a stain removal agent.
dispensed directly onto fabric ·Do not overfill fabric softener dispenser and do not pour liquid fabric
softener directly onto fabric.
See page 13 for more instructions.

Black or gray ·A buildup caused by the interaction ·Keep the recommendations against scum (waxy buildup).
marks on of fabric softener and detergent ·Use correct amount of detergent for load size, soil level,
clothes can flake off and mark clothes and water hardness.
·Not enough detergent

Yellow or ·Iron or manganese in water ·To restore discolored load of whites, use rust remover safe for
brown rust supply, water pipes, or water fabric.
stains heater ·Install nonprecipitating water softener or an iron filter in your
water supply system for an ongoing problem.
·Before washing, run water for a few minutes to clear lines.

Lint ·Incorrect sorting ·Wash lint-producing items, like flannel sheets, towels, and the like
·Tissues left in pocket separately from dark fabrics and fabrics that tend to collect lint.
·Overloading the washer Remove all items, including tissues and papers, from the pockets of
items to be washed. See page 9 for sorting information.
·Do not overload the washer.

Residue or ·Overloading the washer ·Do not overload the washer.

Detergent ·Undissolved detergent ·Some detergents need to be pre-dissolved, check the
·Excessive detergent detergent instructions. Try pre-dissolving the detergent.
·Increase water temperature using HOT water safe for fabric.
·Use proper amount of detergent.

Holes, tears, ·Incorrect use of chlorine bleach. ·Never pour chlorine bleach directly on fabric.
or snags ·Unfastened zippers, hooks, See page 11 for adding liquid bleach.
buckles ·Fasten zippers, hooks, and buckles.
·Ribs, tears and broken threads ·Remove objects in pockets. See page 9 for caring before loading.
·Overloading the washer ·Do not overload the washer.
·Degradation of fabric
30
 Thermistor & Pressure Sensor(BL6) Motor(GY3) Clutch(BL2) (YL2) Pump(BL3)
Pin2 : S1 Pin1 : W Pin1 : Clutch Motor(output)(120VAC) Pin1 : Sensing Pin 1 Pin1 : Common(AC_Live)(120VAC)
Pin3 : Temp(input ) Pin2 : V Pin3 : Clutch_Sensing(Input)(120 VAC) Pin2 : Sensing Pin 2 Pin3 : Drain Pump(output)(120VAC)
Pin4 : GND Pin3 : U
Pin5 : S2
Pin6 : GND

Doorlock Switch(WH6)
Pin1 : GND
Pin2 : LIDLOCK_SIGNAL(Input)
Pin3 : LIDLOCK_CONTROL(Output)
Pin4 : LID_SW
Pin5 : REED_SW

Display(CN2)
Pin1 : 16.5v
Pin2 : LID_SW
Pin3 : BZ_OUTPUT
Pin4 : -
Pin5 : BZ_PWM_SMART

Display(RD2)
Pin1 : NORMAL_CONNECT
Pin2 : NORMAL_OPEN
Pin4 : COMMON
4-5. TROUBLESHOOTING SUMMARY

Display(CN1)
Pin1 : Rx

31
Pin2 : Tx
Pin3 : GND
Pin4 : -
Pin5 : 5v
Pin6 : TEST

Motor
 4-6. PCB Picture

YL3 WH6 RD3

BL2
BL6

32
BL3
YL2

WH1 RD2 RD6

4-7. TROUBLESHOOTING WITH ERROR CODE

ERROR DECISION CAUSE FOR ERROR

ERROR REMEDY
BASIS OCCURRENCE

WATER ·WATER LEVEL ·Water faucet is closed? ·Open water faucet.

SUPPLY dose not rise to ·Water supply is interrupted. Wait until water supply is
the set level in within resumed.
30 minutes. ·Inlet valve is clogged with ·Clean or replace filter.
dirts. ·Correct the connector
NO INLET ·Connector has bad contact contact.
lamp blinks to the inlet valve. ·Same as above.
·RED 6-pin connector has
a bad connection at the main
board.

DRAINAGE ·Water is not ·Is the drain hose located ·Drain hose properly positioned
completely drained properly? at 0.9 ~ 1.2 m (36 ~ 48 inches)
within 12 minutes. ·Drain hose is folded or above the floor.
clogged due to freeze or dirt. ·Make sure the drain hose is not
·Defective drain pump or the plugged with a foreign object.
WHITE 6-pin connector to the ·Check drain pump motor
main board has a bad contact. Replace the pump if
connection. necessary.

UNBALANCE ·Laundry ·Laundry in the INNER TUB ·Load the washer as evenly as
unbalance during is filled unevenly. possible.
spin.
·Washer is tilted. ·Adjust the leg.

LID ·LID is opened in ·Lid is opened during ·Close the lid.

OPEN the course of intermittent spin or normal
intermittent spin, spin?
normal spin or ·Lid is opened while ·Close the lid.
processing processing reservation?
reservation. ·Check the connections to the lid ·Check the connections.
switch and at the WHITE 6-pin ·If the connection is good, check
connector at the main board. the lead wire and replace it if
necessary.

33
 ERROR DECISION CAUSE FOR ERROR
ERROR REMEDY
BASIS OCCURRENCE

PRESSURE ·Pressure switch has a ·Check the connections at the ·Reseat the connector.
SENSOR bad connection or the pressure switch and at the
switch has failed. BLUE 6-pin connector at the
main board. ·Replace the switch.
·Check the pressure sensor
(21~23Ω ±10%) and
connection

OVER ·Check the valves to be sure ·Install the drain hose between
FLOW there is no input leakage. Then 0.9 ~ 1.2 m (36 and 48 inches)
ERROR check the drain hose and make above the floor.
sure the drain pipe is between ·Replace pressure sensor
0.9 ~ 1.2 m (36 and 48 inches) switch
above the floor. ·Remove the foreign objects
·Check for blockages and leaks in pressure sensor switch
in the air hose between the tub air hose.
and the pressure switch.
·Check and repair any air
leakages at the air hose
connector on the outer tub and
at any connecting parts.

MOTOR ·Check the connections at the hall ·Replace the stator if necessary.
ERROR sensor and at the BLUE ·Replace the hall sensor if
6-pin connector on the main board. necessary.
·Check the connections at the ·Replace the bearings if
stator and at the yellow 3-pin or necessary.
BLUE 6-pin connector on the
main board. Test the stator to
determine it is not defective.
·Test hall sensor to determine it
is not defective.
·Turn the drum to verify the
bearings are not locked.

LID ·Check the lid lock SW trying ·If trying, replace the Lid lock
LOCK locking SW or not trying replace the
ERROR ·Check the balance of the lid Main PCB
·Replace the lid or se the
balance

34
 ERROR DECISION CAUSE FOR ERROR
ERROR REMEDY
BASIS OCCURRENCE
THERMISTOR ·Thermistor has a bad ·Check the connections at the ·Reseat the connector.
connection or failed Thermistor and at the WHITE
3-pin connector at the main
board ·Replace the thermistor if
necessary.
·Test thermistor to determine it
is not detective

AC, MOTOR ·AC motor has a bad ·Check the connections at the ·Reseat the connector.
(CLUTCH connection or failed AC motor and at the WHITE
MOTOR) 6-pin connector at the main
·Clutching is failed board
-.Coupling get out of
gear. ·Test AC motor or coupling to
-.Coupling is broken. determine it is not detective ·Replace the AC motor if
necessary.

·Replace the coupling or Clutch

housing if necessary.
MOTOR ·Check Foreign objects, such as ·Turn off the washer and then
coins, pins, clips, etc., being press the Power button.· Press
caught between the wash plate the spin speed button without
and the inner basket. selecting a cycle to drain and spin
the load.· When the spin is
complete, remove the clothes and
then find and remove any objects
caught in the wash plate.

35
 Is the coil of the drain pump Replace the
DRAIN ERROR too high or low? (resistance of Yes DRAIN PUMP
the coil is 10-20 Ω) ASSEMBLY.

No

Is OE displayed? Is the voltage between

connectors out of range? Yes Replace the
MAIN PCB
(BL3 pin3) ASSEMBLY.
- After remove Terminal
Position Assurance
of connector, check as follows.

Yes

Is the connector connected to Reconnect or

pump motor assembly Yes
repair the
disconnected or connector
disassembled?
Pump running : 120V±5%
Stopped Motor/Pump : 0~1V
Method
1. Enter the SERVICE Mode.
2. Press START/PAUSE button.
: 1 time Main version
: 2 times Display version
: 3 times Inlet valve check mode
: 4 times Cold valve, bleach valve
Drain pump : 5 times Rinse valve, hot valve
: 6 times Jet spray valve
: 7 times Heater check
: 8 times Alph check
: 9 times Pump check

[Note] Environmental check list

1) The drainage hose must not stay in a lower position
2) The drainage hose must not be bent or clogged in any
way due to the surrounding physical configuration
3) The drainage hose must not get frozen at all times.
Connection connector 4) The drainage pump must not have any improper
substance or material inside that may cause a
machine breakdown.
No

When you enter the SVC Check the AIR

Mode, is the water level Yes CHAMBER, the
frequency below 26.0 kHz? tube (clogged),
and press
switch

36
 LOCKED MOTOR ERROR - Part of motor

Is LE displayed?

Yes Motor
No
Check the connectors below. Reconnect
Is the connector disconnected Yes the connector Is rotor magnet cracked?
or disassembled? (connector /
(motor drive connector) wire / motor )
Replace the
- Part of main PCB Yes ROTOR
Magnet
assembly (YL3)

No

Is the resistance values

in the range of 5 to15 ­Ω? No Replace the
(U-V, V-W, W-V STATOR
:U=1, V=2, W=3)
Motor Drive - After pull out the YL3
connector, check the terminal
of the connector in wire.
- Part of wire

Motor
Motor Drive
Motor Drive
Drive
Yes

Check the IPM in the Replace the

Yes MAIN PCB
controller. Is IPM short?
ASSEMBLY

37
 UNBALANCE ERROR OVER FLOW ERROR

Is UE displayed? Is FE displayed?

Yes Yes

Does the laundry lean toward When you enter the service
Put laundry evenly
one side, not evenly put in the Yes mode, is the water level No Check the AIR
In the DRUM CHAMBER and the
DRUM assembly? frequency over 21.0 kHz?
assembly tube (clogged).

No Yes

Adjust the height of Does the inlet valve work If the inlet valve
Is the washing machine Yes washing machine No works
installed at an angle? when the power is not
to be kept applied? continuously when
horizontally the power is
applied, replace
Yes
the MAIN PCB
ASSEMBLY
Replace the INLET VALVE
ASSEMBLY

38
 PRESSURE SENSOR ERROR

Is PE displayed?

Yes

Is the connector connected to Reconnect or

pressure sensor disconnected Yes repair the
or disassembled? connector

No

Is the resistance of the Replace the

pressure sensor out of range? Yes pressure switch
(pin 1~ pin 3)
(21~23 Ω±10%)

No

Fix the air

Is the AIR CHAMBER and the Yes chamber and
tube clogged? remove the foreign
material
No

Replace the MAIN PCB

assembly

39
4-8. OTHER TROUBLESHOOTING
CAUTION
1. Be careful of electric shock if disconnecting parts while troubleshooting.
2. First of all, check the connection of each electrical terminal with the wiring diagram.
3. If you replace the main PCB assembly, reinsert the connectors correctly.

NO POWER Is LED on while the power is

Yes Replace the MAIN
on?
PCB ASSEMBLY

Is the supplied voltage Check the fuse or

120V AC?(+10%, -15%) No reset the circuit
breaker

No

Is three pin wire of display Replace the

PCB broken? Yes DISPLAY PCB
Yes ASSEMBLY

Is the current rating of multi- Alternate with

outlet power strip enough? No
explanation
(Avoid connecting several
electric devices)

Display PCB

Yes

Is the connector connected to Reconnect or

PCB/Noise filter disconnected No repair the
or disassembled? connector

Connecting connector
Main PCB~ Display PCB

Yes

40
 POWER BUTTON DOESN’T WORK

Is the connector connected to Reconnect or Is the display PCB broken? Replace the
Main PCB / Display PCB Yes DISPLAY PCB
Yes repair the (check the buzzer sound and
disconnected or connector LED light while touch the ASSEMBLY
disassembled? LCD)

Connecting connector
Main PCB~ Display PCB

No

Is the button of panel stuck?

Yes Repair the button

No

41
5. COMPONENT TESTING INFORMATION
WARNING When resistance (Ohm) checking the component, be sure to turn the power off, and do
voltage discharge sufficiently.

5-1. Filter Assembly (Line Filter)

Circuit in the MAIN PCB / Wiring Diagram

1 1
Wiring 1 1
diagram
Vac 2 2 MAIN PCB
ASSEMBLY
2 2
3 3

WH1 RD1

WH1
(1) (3)

Test
points

and

Result

(2) (1)
RD1

Test Points Result

WH (1) to RD (1) 0Ω

WH (3) to RD (2) 0Ω

42
5-2. Door Lock Switch Assembly.

Circuit in the MAIN PCB / Wiring Diagram

Wiring
diagram

The Door Lock Switch Assembly consists of a Solenoid, Plunger, Level, Key,
Sol-spring and Micro Switch. It locks the door during a wash cycle.

1. Door lock operation

- When a cycle is started, the PCB sends the door lock signal if Reed switch detects that the door
is closed.
- 16.5V is supplied to Solenoid.
- Magnetic force that is caused by solenoid operation inserts Plunger into Solenoid.
- The Level that connected with plunge is pushed out the key.
- The key must be in the proper position for the PCB to sense that the door is locked, otherwise the
dL error code will be displayed.
- If the latch does not extend far enough, the PCB will display the dL error code. This can happen,
for example, if the solenoid does not operate.
Function Note: The door will attempt to lock 3 times. If it does not successfully lock, the solenoid will drive
the latch to the open position.

2. Door unlock operation

- When the cycle ends, or if the cycle is paused, the PCB sends an unlock pulse to the solenoid.
-The key will attempt to unlock three times. If it fails to sense that the door is unlocked,
the solenoid will be driven to the lock position.

43
 (1)

(10)
(5)
(4)
(7)
(3)
(13)
(9) (2)

(6) (12)

(8)
(11)

Test points No. Parts

1 COVER
2 SCREW
3 LEAD WIRE
4 PACKING
5 SOLENOID
6 CASE
7 HAND WIRE
8 MICRO SW
9 SOL-SPRING
10 PLUNGER
11 KEY
12 LEVER
13 RUBBER CASE

44
5-3. STATOR ASSEMBLY

Circuit in the MAIN PCB / Wiring Diagram

Wiring
diagram

The DD motor can be driven from stopped to maximum speed in infinite steps in either direction.
There are 36 poles on the stator; 12 permanent magnets spaced around the rotor. There are no
Function
brushes to wear out. Unlike a more traditional brushless motor, the rotor surrounds the stator
rather than being attached to it.

WINDINGS

Test points
(Windings)

(1) (2) (3)

Test Points Result

(1) to (2) 5-15 Ω
Result
(2) to (3) 5-15 Ω
(Windings)
(3) to (1) 5-15 Ω

45
5-4. PUMP MOTOR ASSEMBLY

Circuit in the MAIN PCB Wiring Diagram

Wiring
diagram

Test Points Result Remarks

(1) (2)
(1) to (2) 10.9 Ω±5% Resistance

Test
points
and
Result

46
5-5. INLET VALVE ASSEMBLY

Circuit in the MAIN PCB

Inlet valve driving circuit

Wiring Wiring diagram

diagram

INLET VALVE
* All valves operate at 13.5 VDC.

Depending on the cycle and water temperature, the controller will energize the hot or cold water
Function valve solenoids to meet the selected water temperature.

After unplugging the connector of the defective valve, check the resistance.

Test
(1)-(2)
Test Points
points Result 24±10% [Ω]
(2) (2) (1)
and (1) (1) (2) (2)
(1) (2) (1)
Result

47
5-6. THERMISTOR ASSEMBLY

Circuit in the MAIN PCB / Wiring Diagram

Wiring
diagram

MAIN PCB

The thermistor (temperature sensor) is used to monitor water temperature in the tub.
Function

Test
points

(1) (2)

Wash Thermistor

48
 Wash Thermistor

Result [㏀]
Test Points Remarks
The lowest standard The upper
limit limit

(1) to (2) 70.519 76.531 82.848 At 86℉ (30℃)

Result
46.997 50.584 54.307 At 104℉ (40℃)

22.285 23.623 24.978 At 140℉ (60℃)

15.803 16.635 17.467 At 158℉ (70℃)

6.984 7.471 7.971 At 203℉ (95℃)

5.180 5.573 5.981 At 221℉ (105℃)

49
5-6. HEATER ASSEMBLY

Circuit in the MAIN PCB Wiring diagram

Wiring
diagram

Heater driving circuit

WASH
HEATER

* Each circuits of loads in wiring diagram are all same.

1. The Wash Heater is designed to raise the wash water to the desired temperature selection during
Function certain wash cycles.
2. The Steam generator heater is designed to make the water to the steam during steam cycles.

Teat
points
(1) (2)

Wash Heater

Wash Heater
Test Points Result
Result
(1) to (2) 12-18 k Ω

50
6. EXPLODED VIEW

BODY-A

BODY-B

51
A020
A010

A030
A040
A240
A050 A203
A202
A201
A200

A062
A152
A061 A063 A190
A154
A153
A101
A163 A151
A150
A165
A230
A410

A100
A101
A241

A165
A163

A180
A380
A183

A390
6-2. EXPLODED VIEW OF OUTER CASE ASSEMBLY

F032

F016

F070

F000

F100
F090

F150 F020

F086

F080

F027
F023
F082

53
6-3. EXPLODED VIEW OF TUB ASSEMBLY

K005

K000

K012

K021

K020

K030
K040
K050

K061
NATURAL
K100
K060

K104

K250

K350 K064

K170
K140

K345
K340

K200
K290
K230

K210

K201

K305
K410 K300 K400 K420

54
7. REPLACEMENT PART LIST

55
 WT1801H*A /01 Wiring Diagram
DISPLAY PWB POWER BUTTON
CN1 CN2 CN3
1 2 3 4 5 6 1 2 3 4 5 1 2 3 4 5

1 2 3 4 5 6 1 2 3 4 5 1 2 3 4
MAIN PWB
CN1 CN2 RD2
8. Wiring Diagram

56
Error Message
IE - WATER SUPPLY ERROR
NOTES OE - DRAIN ERROR
Motor UE - UNBALANCE ERROR
Test Mode dE - LID OPEN ERROR
Press Power PE - PRESSURE - SENSOR ERROR
Function Test while operationg Wiring Color Legend Press Steam & Turbo Key (in 1 sec.) FE - OVER FLOW ERROR
Press Fabric Softener & Custom PGM = Water Temp. Press START/PAUSE to cycle thru tests LE - MOTRO ERROR
BL - Blue BN - Brown GN - Green GY - Gray dL - LID LOCK ERROR
Press Delay & Spin Speed = Water Supply Frequency Component Tests
PK - Pink RD - Red SB - Sky Blue WH - White tE - THERMISTOR ERROR
Press Custom PGM & Soil Level = Motor RPM Voltage Tests with connectors installed
YL - Yellow Chm Tests with connectors removed E6 - AC, MOTOR ERROR
Press Delay & Soil Level = IPM Temp.
JAN 2015 PRINTED IN KOREA MFL68909505