Scribd
Upload
5 views

General

general

Uploaded by

Aziz Hoq
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
5 views

General

general

Uploaded by

Aziz Hoq
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Civil

1. If T-Shaped beam is passing through many supports, the section above the support should be designed as?
rectangle section
2. If T-Shaped beam is passing through many supports, the section in middle should be designed as? T
section
3. If the load magnitude on a traditional R.C column increases continuously, the allowable moment in one plane is
constant.
zero
4. Slump test of concrete is used for
Consistency
5. What is the factor not to be taken in consideration in mix design?
 Degree of control of concrete
 Strength of concrete
 Time of first set of cement
 Workability
6. What is the formula of nominal moment in concrete ?
 Mn = Fs.As(d –c/2 )
 Mn = Fs.As(d – a)
 Mn = 0.85f’c.ab(d – a/2)
 Mn = 0.85f’c.ab(d – a/2) + Fs.As(d – a/2)
7. Something about flow in pipes, 2 pipes A and B joined together into pipe C Flow A given& Flow B given& Area
C given. Calculate velocity of water in C.
8. Calculate the length of arc, radius 250m, first tangent 25˚30’, second tangent 30˚25’
9. What is the factor effecting the hardness of water ?
10. How to calculate T-beam … (flanged section)
11. Who make testing of product in the factory
 Testing engineer
 Research engineer
 Product engineer
12. Calculate the fill/excavation (CY)
13. What is the advantage of using concordant cable in pre-stressed concrete?
14. What are RC columns execution sequences?
15. Calculate the displacement for truss.
16. What is the slope at section ..(.. EI=constant
17. Why in two way slab, lifting of corner slab happens from ..?
18. 10#@10/m to change to 12# how much the new space?
12#@15/m
19. What is the last of stage of sewage treatment plant?
20. When design RC section, whether the concrete at tension side will be neglected or considered?
considered
21. Air-Entrained Concrete is used to
Forest resistance & durability & light weight
22. The station is 00,.000 with elevation of 178.00 what is the filling required
23. What is the nearest to 100 Yard (1:100, 1: 1000, 1:1500)
24. What is hydration in concrete?

Page 1
Civil
25. Calculate joint deflection when membrane temperature increases.
26. What is the function of admixtures in concrete?
27. Calculate the horizontal displacement for a truss.
28. What is the effect of air within poured concrete?
Forest resistance & durability & light weight
29. What is the weight of concrete?
25kn/m3
30. What is the yield strength of steel?
400 MPA
31. What is the strength of concrete?
32. What is the maximum allowable stress redistribution in RCC beams (%)?
33. Tensile strength in wood (direction wrt grains).
parallel to the grain
34. Calculate deflection @ a joint.
35. Where is maximum bending stress located/ how is it distributed when placing a load on the beam’s C-S (linear/
Parabolic/uniform/ @ top & bottom)
36. Over Flow rate 35m3/w/day, Tank 2.5 x 4 x 16 m then Flow Rate
2240 m3/day
800m3/day
350m3/day
0.22m3/day
37. Two Way Slab to consider
- Shear at edges
- Sleep in middle
- - Compression in Middle

10 20
1.
B
38. Calculation Movement at B
2. C EA given

A B
Calculate the Horizontal force of B
39. In ''T'' the section beam Design as
Simple Support
Rectangular
40. What is the stress in membrane
tensile stress
41. What is the last additional in Cement Factory ?
- Silica
- Aluminum
- Calcium Sulphate
- None of above

Page 2
Civil
42. FTh ..What is FTh ?
- 0.25
- 0.35
- 1
43. Bricks
a. Motor is an effect to strength of Brick wall.
b. Lime stone is an effect of Strength of Bricks.
c. Motor is considered the main effect of strength of Brick wall.
d. All of the above
44. Sheet force + Fiber
45. Concrete cubes usually crushed at
2 days
8 days
28 days
30 days
46. Steel yield strength usually used at site in MPA:
400
200
100
300

47. Calculate the deflection at point A

9.75P/EA

21P/EA

42P/EA

48. Method …………. Beam

Bernoulli- Foiler

Filler and some other names which I don’t recall

49. Bleeding can be controlled by :


Adding cement
More vibrating concrete
Adding aggregate
Adding fresh concrete
50. Increasing Concrete strength is affected by:
Increasing Water cement ratio in high workability concrete
Vibrating concrete in high water cement ratio
Bad aggregate sieve and gradation.

51. What is shear span:

Page 3
Civil
Moment is zero
Shear is zero
Moment is maximum
52. Main factor in concrete movement is
Settlement
53. Calculate cross section area related to
Radius
54. Foot area is 2.20m2 and column 0.25*0.80 m footing dimension is
Rectangular 1.25*1.80 m
55. What is affect on concrete
Shapes and surface of aggregate
56. To convert from metric to inch
÷2.54

Page 4

You might also like