QSF-T15 series

Start Up Checks
Weekly Checks
Close Down Checks
Splicing and Developing
List of Modes
Start Up Checks
Processing solution can cause eye irritation.
Be sure to put the safety goggles on when carrying out this operation.
WARNING Processing solution can cause skin irritation.
Be sure to wear rubber gloves and clothing for work wear.

Press .
1 EXECUTE START CHECK

Press .
2
Unlocked. Locked.

ATTACH UPPER TURN GUIDES

PROPERLY

Confirm that the upper turn guides

are locked properly.

Press .
3
Unlocked. Locked.

ATTACH SQUEEGEE RACK

PROPERLY

Remove the moisture on the squeegee rack

off then attach it properly.

Press .
4
Unlocked. Locked.

CHECK IF RACK STOPPER

IS SET PROPERLY
5
Press . Film stocker

CLOSE TOP COVER

Top cover

Close the top cover and attach

the film stocker.

6 TURN ON DRIVE SWITCH OFF

ON

7 EXECUTE AUTO
WATER REFILLING

This step is not necessary if the message

Press . "EXECUTE AUTO WATER REFILLING"
is not shown.
REFILLING
 Insert the leader card.
8 OPEN LOADING COVER

INSERT LEADER CARD Loading cover

CLOSE LOADING COVER

LEADER CARD BEING FED

Align the rear edge of the leader card

with the orange line.

LEADER CARD TEST

FINISHED?

Remove the leader card.

Press .
9 PROCESS CONTROL STRIP? INSERT CONTROL STRIP

Press .
NOTE
CLOSE LOADING COVER
When the control strip processing
is unnecessary such as in the case
of maintenance, press .

OPEN LOADING COVER CONTROL STRIP BEING FED

This completes the Start Up Checks.

For details, refer to section 1.2.1 Carrying out Start Up Checks, in the Operator’s Manual - for operator -.
Weekly Checks Execute the Weekly Checks when the message,
“TODAY IS MAINTENANCE DAY” appears at the Start Up Checks.

Processing solution can cause eye irritation.

Be sure to put the safety goggles on when carrying out this operation.
WARNING Processing solution can cause skin irritation.
Be sure to wear rubber gloves and clothing for work wear.

1 EXECUTE START CHECK

TODAY IS MAINTENANCE DAY

Upper turn guide 2

(1) Remove the inlet guide,
2
Squeegee rack Upper turn guide 5 Inlet guide
upper turn guides 2 and 5.
CAUTION
When the squeegee rack is
attached, remove it as well.

(2) Wash the inlet guide, upper turn guides 2

and 5, and squeegee rack with running
lukewarm water.

Wash the processing racks in order of the

3 number on the racks from the upper side
using the washing bottle.

Reattach the inlet guide, upper turn guides 2 and 5, and squeegee rack as they were.
4 IMPORTANT
Reattach the inlet guide after drying it completely.
Reattach upper turn guides 2 and 5, and squeegee rack after removing
the moisture off.

This completes the Weekly Checks.

For details, refer to section 1.2.1 Carrying out Start Up Checks, in the Operator’s Manual - for operator -.
Close Down Checks
Processing solution can cause eye irritation.
Be sure to put the safety goggles on when carrying out this operation.
WARNING Processing solution can cause skin irritation.
Be sure to wear rubber gloves and clothing for work wear.

Press .
1 EXECUTE CLOSE CHECK

2
Press . ON

TURN OFF DRIVE SWITCH

OFF

3 EXECUTE AUTOMATIC CLEANING

Press .

AUTOMATIC CLEANING PROCEEDING

4 REMOVE SQUEEGEE RACK

Wash the squeegee rack and soak it in

a vat filled with water.
 Press .
5 CHECK REFILLING WATER LEVEL

When the water level in the refilling

water tank is low, add water.

Press . In the case of with a effluent valve cover

6 DRAIN WASTE SOLUTION TANKS

In the case of without a effluent valve cover

Press .
7 LEAVE THE TOP COVER SLIGHTLY
OPEN

Press .
8 PROGRAM TIMER OPERATING

This completes the Close Down Checks.

For details, refer to section 2.1.1 Carrying out Close Down Checks, in the Operator’s Manual - for operator -.
 Splicing and Developing Splicing is the operation to join the film with
the leader card.

This section explains how to splice 135 film.

For how to splice 110 film, refer to the Operator’s Manual - for operator -.
For how to splice IX240 film, refer to the Operator’s Manual of Film Processor Modification Parts for IX240.

There is a danger of cutting hands on edged tools.

CAUTION Keep your hands away from edged tools.

Pull the film tongue and attach

1
Check labels
the check label.

Check the leader card.

2 CAUTION
If glue of splicing tape is left
on the leader card, wipe it
off completely.

IMPORTANT

Never use the leader cards under the following conditions.

5 mm or more
1 mm or more 1.5 mm or more

Damage at the edge Horizontal curl with Vertical curl with Protruded perforation with
1 mm or more 5 mm or more 1.5 mm or more

Raise the film holder and cutter of

3 the splicing gauge.
Film holder
Cutter

Tape dispenser
(option)

Splicing gauge
 Set the film on the splicing gauge
4 and fix it with the film holder.

The forth perforation

on the short side of the film tongue

Lower the cutter and cut

5 the film tongue.

6
Set the leader card.

Film is set on the leader card.

The fifth perforation

 Splice the film and leader card with splicing tape.
7 IMPORTANT
Do not use the joint part of the splicing tape, the adhesive face
exposed to the air for a long time (more than five hours) or with
hand sebum.

Film holder A=B

Leader card

3-5 Splicing tape

mm

Press the splicing tape lightly with

8 your finger and remove the air
bubbles under the splicing tape
Tape spatula

with the tape spatula.

Raise the film holder then take out

9 and hold both the film cartridge
and the leader card as shown in
the figure.
 Check that the ready lamp lights in
10
Ready lamp
green.

11
Insert the film and the leader card into the loading box.
IMPORTANT
Align the rear edge of the leader card with the orange line, and then
close the loading cover.

LEADER CARD BEING FED

Film cartridge

Loading Leader card Orange line

cover

Wait until the film and leader card

12
Film stocker
Film and leader card
are ejected into the film stocker.

This completes splicing and developing.

For details, refer to section 3.1 Developing film(s), in the Operator’s Manual - for operator -.
 List of Modes
READY

MAIN MENU

SWITCHES REPLENISHMENT SWITCH *1*3

DISPLAY CONTRAST
BUZZER VOLUME

TEMPERATURE TEMPERATURE DISPLAY

SOLUTION TEMP. SETTING
THERMOSENSOR CALIBRATION

TOTALING TODAY'S ROLLS

TOTAL ROLLS

CHECK INPUT CHECK LOADING

PROCESSOR
VERSION CHECK
DIGITAL FLOWMETER

FILM POSITION POSITION DATA

TIMER DATE & TIME DISPLAY

DATE & TIME SETTING
PROGRAM TIMER SETTING
MAINTENANCE DAY SETTING

REPLENISH. /REFIL.WATER REPLENISHMENT TOTAL REPLENISH. AMOUNT *3

MANUAL REPLENISHMENT *1*3
BASIC REPL. AMOUNT *3

PUMP AMOUNT SETTING

PUMP AMOUNT MEASUREMENT
REPLENISHMENT LACK TIME *1*3
ROOM CONDITION *1*2
REFILLING WATER *3

FLOPPY DISK FLOPPY DISK READING/WRITING

SOFTWARE UPGRADE
FORMAT
These modes require the owner password.
This mode is shown only when the digital flowmeter is equipped.
*1: This mode is not shown on the SM specification.
*2: This mode is not shown on the standard specification.
*3: This mode is not shown on the F specification.

These modes may be changed without notice. Check according to the Operator's Manual - for administrator -.