NOT RECOMMENDED FOR NEW DESIGN

USE S1A-S1M series 1N4001 - 1N4007

1.0A RECTIFIER

Features
 Diffused Junction
 High Current Capability and Low Forward Voltage Drop
 Surge Overload Rating to 30A Peak
 Low Reverse Leakage Current
 Lead Free Finish, RoHS Compliant (Note 3)

Mechanical Data
DO-41 Plastic
 Case: DO-41 Dim
Min Max
 Case Material: Molded Plastic. UL Flammability Classification A 25.40 
Rating 94V-0 B 4.06 5.21
C 0.71 0.864
 Moisture Sensitivity: Level 1 per J-STD-020D
D 2.00 2.72
 Terminals: Finish - Bright Tin. Plated Leads Solderable per All Dimensions in mm
MIL-STD-202, Method 208
 Polarity: Cathode Band
 Ordering Information: See Page 2
 Marking: Type Number
 Weight: 0.30 grams (Approximate)

Maximum Ratings and Electrical Characteristics (@TA = +25°C unless otherwise specified.)
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Characteristic Symbol 1N4001 1N4002 1N4003 1N4004 1N4005 1N4006 1N4007 Unit
Peak Repetitive Reverse Voltage VRRM
Working Peak Reverse Voltage VRWM 50 100 200 400 600 800 1000 V
DC Blocking Voltage VR
RMS Reverse Voltage VR(RMS) 35 70 140 280 420 560 700 V
Average Rectified Output Current (Note 1) @ TA =+75C IO 1.0 A
Non-Repetitive Peak Forward Surge Current 8.3ms
IFSM 30 A
Single Half Sine-Wave Superimposed on Rated Load
Forward Voltage @ IF = 1.0A VFM 1.0 V
Peak Reverse Current @TA = +25C 5.0
IRM A
at Rated DC Blocking Voltage @ TA = +100C 50
Typical Junction Capacitance (Note 2) Cj 15 8 pF
Typical Thermal Resistance Junction to Ambient RJA 100 K/W
Maximum DC Blocking Voltage Temperature TA +150 C
Operating and Storage Temperature Range TJ, TSTG -65 to +150 C
Notes: 1. Leads maintained at ambient temperature at a distance of 9.5mm from the case.
2. Measured at 1.0 MHz and applied reverse voltage of 4.0V DC.
3. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied, see EU Directive 2002/95/EC Annex Notes.

1N4001-1N4007 1 of 3 September 2014

© Diodes Incorporated
Document number: DS28002 Rev. 9 - 3 www.diodes.com
 NOT RECOMMENDED FOR NEW DESIGN
USE S1A-S1M series

I(AV), AVERAGE FORWARD RECTIFIED CURRENT (A)

IF, INSTANTANEOUS FORWARD CURRENT (A)

1.0 10

0.8

1.0
0.6

0.4
0.1

0.2
Tj, = 25oC
Pulse Width = 300 s
2% Duty Cycle
0 0.01
40 60 80 100 120 140 160 180 0.6 0.8 1.0 1.2 1.4 1.6

TA, AMBIENT TEMPERATURE (ºC) V F, INSTANTANEOUS FORWARD VOLTAGE (V)

Fig. 1 Forward Current Derating Curve Fig. 2 Typical Forward Characteristics
50 100
Tj = 25ºC
IFSM, PEAK FORWARD SURGE CURRENT (A)

f = 1MHz

40

Cj, CAPACITANCE (pF)

30
1N4001 - 1N4004

10

20
1N4005 - 1N4007

10

0 1.0
1.0 10 100 1.0 10 100
NUMBER OF CYCLES AT 60 Hz VR, REVERSE VOLTAGE (V)
Fig. 3 Max Non-Repetitive Peak Fwd Surge Current Fig. 4 Typical Junction Capacitance

Ordering Information (Note 4)

Device Packaging Shipping
1N4001-B DO-41 Plastic 1K/Bulk
1N4001-T DO-41 Plastic 5K/Tape & Reel, 13-inch
1N4002-B DO-41 Plastic 1K/Bulk
1N4002-T DO-41 Plastic 5K/Tape & Reel, 13-inch
1N4003-B DO-41 Plastic 1K/Bulk
1N4003-T DO-41 Plastic 5K/Tape & Reel, 13-inch
1N4004-B DO-41 Plastic 1K/Bulk
1N4004-T DO-41 Plastic 5K/Tape & Reel, 13-inch
1N4005-B DO-41 Plastic 1K/Bulk
1N4005-T DO-41 Plastic 5K/Tape & Reel, 13-inch
1N4006-B DO-41 Plastic 1K/Bulk
1N4006-T DO-41 Plastic 5K/Tape & Reel, 13-inch
1N4007-B DO-41 Plastic 1K/Bulk
1N4007-T DO-41 Plastic 5K/Tape & Reel, 13-inch
Note: 4. For packaging details, visit our website at http://www.diodes.com/datasheets/ap02008.pdf.

1N4001-1N4007 2 of 3 September 2014

© Diodes Incorporated
Document number: DS28002 Rev. 9 - 3 www.diodes.com
 NOT RECOMMENDED FOR NEW DESIGN
USE S1A-S1M series

IMPORTANT NOTICE

DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
(AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).

Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes
without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the
application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or
trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume
all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated
website, harmless against all damages.

Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and
hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or
indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.

Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings
noted herein may also be covered by one or more United States, international or foreign trademarks.

This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the
final and determinative format released by Diodes Incorporated.

LIFE SUPPORT

Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express
written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:

A. Life support devices or systems are devices or systems which:

1. are intended to implant into the body, or

2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the
labeling can be reasonably expected to result in significant injury to the user.

B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or to affect its safety or effectiveness.

Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any
use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related
information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its
representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.

Copyright © 2014, Diodes Incorporated

www.diodes.com

1N4001-1N4007 3 of 3 September 2014

© Diodes Incorporated
Document number: DS28002 Rev. 9 - 3 www.diodes.com
 RB068LB100
Schottky Barrier Diode
Data sheet
● Outline
VR 100 V
Io 2 A

IFSM 90 A

● Features ● Inner Circuit

High reliability
Small power mold type
Super low IR

● Application ● Packaging Specifications

General rectification Packing Embossed Tape
Reel Size(mm) 330
Taping Width(mm) 12
● Structure Quantity(pcs) 3000
Silicon epitaxial planar Taping Code TBR1
Marking K2
● Absolute Maximum Ratings (Tc=25ºC unless otherwise specified)
Parameter Symbol Conditions Limits Unit
Repetitive peak reverse voltage V RM Duty≦0.5 100 V
Reverse voltage VR Reverse direct voltage 100 V
Glass epoxy mounted、
Average rectified forward current Io 60Hz half sin waveform、resistive load、 2 A
Tc=158℃ Max.
60Hz half sin waveform、Non-repetitive、
Peak forward surge current IFSM one cycle、Ta=25℃ 90 A
Junction temperature(1) Tj - 175 ℃
Storage temperature Tstg - -55 ～ 175 ℃
Note(1) To avoid occurrence of thermal runaway ， actual board is to be designed to fulfill dPd/dTj<1/Rth(j-a).
● Characteristics (Tj=25ºC unless otherwise specified)
Parameter Symbol Conditions Min. Typ. Max. Unit
Forward voltage VF IF=2A - - 0.81 V
Reverse current IR V R=100V - - 1.5 μA

Attention

www.rohm.com
© 2022- ROHM Co., Ltd. All rights reserved. 1/5
2022/12/22_Rev.002
RB068LB100 Data sheet

● Characteristic Curves

www.rohm.com
© 2022- ROHM Co., Ltd. All rights reserved. 2/5 2022/12/22_Rev.002
RB068LB100 Data sheet

● Characteristic Curves

www.rohm.com
© 2022- ROHM Co., Ltd. All rights reserved. 3/5 2022/12/22_Rev.002
RB068LB100 Data sheet

● Characteristic Curves

www.rohm.com
© 2022- ROHM Co., Ltd. All rights reserved. 4/5 2022/12/22_Rev.002
RB068LB100 Data sheet
● Dimensions
DO-214AA (SMB), (SMBP)

●Taping (Unit:mm)

www.rohm.com
© 2022- ROHM Co., Ltd. All rights reserved. 5/5 2022/12/22_Rev.002
 Notice
Precaution on using ROHM Products
1. Our Products are designed and manufactured for application in ordinary electronic equipment (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN USA EU CHINA
CLASSⅢ CLASSⅡb
CLASSⅢ CLASSⅢ
CLASSⅣ CLASSⅢ

2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

3. Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used.
However, recommend sufficiently about the residue.) ; or Washing our Products by using water or water-soluble
cleaning agents for cleaning residue after soldering
[h] Use of the Products in places subject to dew condensation

4. The Products are not subject to radiation-proof design.

5. Please verify and confirm characteristics of the final or mounted products in using the Products.

6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.

7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.

8. Confirm that operation temperature is within the specified range described in the product specification.

9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.

Precaution for Mounting / Circuit board design

1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification

Notice-PGA-E Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.

2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.

Precaution for Electrostatic

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).

Precaution for Storage / Transportation

1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl 2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic

2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.

3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.

4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.

Precaution for Product Label

A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.

Precaution for Disposition

When disposing Products please dispose them properly using an authorized industry waste company.

Precaution for Foreign Exchange and Foreign Trade act

Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.

Precaution Regarding Intellectual Property Rights

1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.

Notice-PGA-E Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
 Datasheet

General Precaution
1. Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.

2. All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales
representative.

3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or
liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccuracy or errors of or
concerning such information.

Notice – WE Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

ROHM Semiconductor:
RB068LB100TBR1
    Order this document
SEMICONDUCTOR TECHNICAL DATA by 1N4933/D

   

  
Axial–lead, fast–recovery rectifiers are designed for special applications such
as dc power supplies, inverters, converters, ultrasonic systems, choppers, low
 
RF interference and free wheeling diodes. A complete line of fast recovery 1N4935 and 1N4937 are
rectifiers having typical recovery time of 150 nanoseconds providing high Motorola Preferred Devices

efficiency at frequencies to 250 kHz.

Mechanical Characteristics FAST RECOVERY

• Case: Epoxy, Molded RECTIFIERS
• Weight: 0.4 gram (approximately) 50–600 VOLTS
• Finish: All External Surfaces Corrosion Resistant and Terminal Leads are 1.0 AMPERE
Readily Solderable
• Lead and Mounting Surface Temperature for Soldering Purposes: 220°C
Max. for 10 Seconds, 1/16″ from case
• Shipped in plastic bags, 1000 per bag.
• Available Tape and Reeled, 5000 per reel, by adding a “RL” suffix to the
part number
• Polarity: Cathode Indicated by Polarity Band
• Marking: 1N4933, 1N4934, 1N4935, 1N4936, 1N4937

CASE 59–03
DO–41

MAXIMUM RATINGS (1)

Rating Symbol 1N4933 1N4934 1N4935 1N4936 1N4937 Unit
*Peak Repetitive Reverse Voltage VRRM 50 100 200 400 600 Volts
Working Peak Reverse Voltage VRWM
DC Blocking Voltage VR
*Non–Repetitive Peak Reverse Voltage VRSM 75 150 250 450 650 Volts
RMS Reverse Voltage VR(RMS) 35 70 140 280 420
*Average Rectified Forward Current IO 1.0 Amp
(Single phase, resistive load,
TA = 75°C) (2)
*Non–Repetitive Peak Surge Current IFSM 30 Amps
(Surge applied at rated load
conditions)
Operating Junction Temperature Range TJ – 65 to +150 °C
Storage Temperature Range Tstg – 65 to +150

THERMAL CHARACTERISTICS
Characteristic Symbol Max Unit
Thermal Resistance, Junction to Ambient RθJC 65 °C/W
(Typical Printed Circuit Board Mounting)
* Indicates JEDEC Registered Data for 1N4933 Series.
(1) Ratings at 25°C ambient temperature unless otherwise specified.
(2) Derate by 20% for capacitive loads.

Preferred devices are Motorola recommended choices for future use and best overall value.

Rev 3

Rectifier Device
Motorola, Inc. 1996 Data 1
  
ELECTRICAL CHARACTERISTICS
Characteristic Symbol Min Typ Max Unit
Instantaneous Forward Voltage vF — 1.0 1.2 Volts
(IF = 3.14 Amp, TJ = 125°C)
Forward Voltage VF — 1.0 1.1 Volts
(IF = 1.0 Amp, TA = 25°C)
*Reverse Current (Rated dc Voltage) TA = 25°C IR — 1.0 5.0 µA
TA = 100°C — 50 100

*REVERSE RECOVERY CHARACTERISTICS

Characteristic Symbol Min Typ Max Unit
Reverse Recovery Time trr ns
(IF = 1.0 Amp to VR = 30 Vdc) — 150 200
(IFM = 15 Amp, di/dt = 10 A/µs) — 175 300
Reverse Recovery Current IRM(REC) — 1.0 2.0 Amp
(IF = 1.0 Amp to VR = 30 Vdc)
* Indicates JEDEC Registered Data for 1N4933 Series.

PACKAGE DIMENSIONS

B
NOTES:
1. ALL RULES AND NOTES ASSOCIATED WITH
JEDEC DO–41 OUTLINE SHALL APPLY.
2. POLARITY DENOTED BY CATHODE BAND.
3. LEAD DIAMETER NOT CONTROLLED WITHIN F
D DIMENSION.
K
MILLIMETERS INCHES
F DIM MIN MAX MIN MAX
A 4.07 5.20 0.160 0.205
B 2.04 2.71 0.080 0.107
A D 0.71 0.86 0.028 0.034
F ––– 1.27 ––– 0.050
K 27.94 ––– 1.100 –––
F
K

CASE 59–03
(DO–41)
ISSUE M

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4–32–1,
P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447 Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan. 81–3–5487–8488

Mfax: [email protected] – TOUCHTONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
– US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
INTERNET: http://motorola.com/sps

2 ◊ 1N4933/D
Rectifier Device Data