Scribd
Upload
197 views

10 Physics Experiment Ohms Law

Uploaded by

Mannu Sagar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
197 views

10 Physics Experiment Ohms Law

Uploaded by

Mannu Sagar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Science Lab Manual Class 10 Experiment

Aim
To study the dependence of potential difference (V) across a resistor on the current
(I) Passing through it and determine its resistance. Also plot a graph between V and
I.
Theory

 Ohm’s Law: The potential difference, V across the ends of a given metallic
wire in an electric circuit is directly proportional to the current flowing through it,
provided its temperature is the same. This is Ohm’s law.
V𝖺I
V = IR, (Here R = Constant for the given metallic wire)
 The SI unit of resistance is Ohm (Ω).

 One Ohm: If the potential difference across the ends of a conductor is 1 volt
and the current flowing through it is 1 ampere, then the resistance of the
conductor R is 1 ohm.

 Factors affecting resistance:


 The nature of resistor (a conductor having some resistance.)
 The length of the resistance. (R ∝ l)
(Resistance increases as the length of the wire is increased)

 The area of cross-section of the resistor.


(Resistance decreases with the increase in the cross-section area of the wire)
 Circuit Diagram:

 In a circuit ammeter is always connected in series and voltmeter is connected


in parallel across the points between which potential difference is to be
measured.
 A straight line graph obtained between V and I verifies the Ohm’s law.
 Least Count: It is very important to find the least count of ammeter and
voltmeter before using them.
If in the ammeter, there are 10 divisions from 0 to 0.1 A then each division indicates
0.01 A.
A. To calculate the least count of ammeter.
Range of ammeter = AR…………………….
Number of divisions in ammeter = AN…………………………..

.’. Least count of ammeter = = ........................ampere.


B. To calculate the least count of voltmeter.
Range of voltmeter = VR……………………
Number of divisions in voltmeter = VN

.’. Least count of voltmeter = = ......................... volt.

Materials Required
A battery, an insulated copper wire (cut into 10 pieces), a key, an ammeter, a
voltmeter, a rheostat, a resistor and a piece of sand paper.
Procedure

1. Keep the devices as shown in the circuit diagram.


2. Connect them with the connecting wires and keep the key open.
3. Positive terminal of the battery is connected to the positive terminal of the
ammeter.
4. Check the +ve and -ve terminals of voltmeter before connecting it in the circuit.
5. Once the circuit is connected, insert the key and check the rheostat, adjust its
slider and see whether the ammeter and voltmeter readings are shown.
6. By using the slider of rheostat take three different readings of current I and
voltmeter V.
7. Record your observations in the observation table.

8. Calculate resistance of a given resistor by formula .


9. Plot a graph of voltmeter reading and current reading. On x axis take V and on
y axis take I.
10. Resistance increases with increase in temperature of pure metals.

Observation Table
Least count of ammeter and voltmeter
S. No. Ammeter (A) Voltmeter (V)

1 Range 0 – 0.5 A 0-0.1 V


.

2 Least Count 0.01 A 0.01 V


.

3 Zero Error (e) 0 0


.

4 Zero Correction 0 0
.

Reading of ammeter and voltmeter

Current in Ampere (I) Potential difference in Volts (V)

(Ammeter Reading) (Voltmeter Reading)


S. No. Resistance in Ohms R = V/I(Ω)

Observed Corrected Observed Corrected

1. 0 0.02 0 0.04 R1 =2 Ω

2. 0 0.03 0 0.06 R2 = 2 Ω

3. 0 0.04 0 0.08 R3 = 2Ω
Conclusions

1. The value of R is found to be same and constant in all three readings.


2. The resistance of a resistor is ratio of potential difference V and current I.
3. The graph of V and I is a straight line. This shows that V𝖺I. This verifies Ohm’s
law.

Precautions

1. The connecting wires should be thick copper wires and the insulation of their
ends should be removed using the sand paper.
2. Connections should be tight otherwise some external resistance may introduce
in the circuit.
3. Connections should be made as per the circuit. Before closing the circuit show
the connections to the teacher to take the readings.
4. The ammeter should be connected in series with the resister such that the
current enters at the positive terminal and leaves at the negative terminal of the
ammeter.
5. Voltmeter should always be connected in parallel to resistor.
6. Calculate the least count of voltmeter and ammeter correctly.
7. The pointers of the ammeter and voltmeter should be at zero mark when no
current flows through the circuit.

You might also like