Scribd
Upload
9 views

Pert 4 - K2

Uploaded by

Bigboss
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
9 views

Pert 4 - K2

Uploaded by

Bigboss
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Pu= Ry Fy Ag

Limit state: fracture of net section

For A36 Angles: For A572 Gr. 50 Angles:

Need to Reinforce Net Section (Ae need not exceed Ag )

81

Also check block shear rupture of bracing member....


Jika batang di tarik maka akan timbul block shear
seperti digambar

setiap kegagalan diakibatkan oleh ketidakmampuan


material, oleh sebab itu dipergunakan (Fu)

Pu= Ry Fy Ag

0.6 Anv Rt Fu
 Pn = (0.75) Ubs Ant Rt Fu + lesser of
0.6 Agv Ry Fy

82

41
Reinforcing net section of bracing member....

83

Example gusset plate


Jika merancang bracing. maka jangan
rectangular HSS bracing menggunakan profil C maupun Profil U,
sebaiknya menggunakan profil H
member
Kecuali jika di double

Check HSS bracing member for limit state


of net section fracture

84

42
85

Pu= Ry Fy Ag

Required axial tension strength


of brace for limit state of
fracture of the net section

86

43
Pu= Ry Fy Ag

Critical Net Section


Ae = U An
Ae < Ag due to:
slot (An < Ag ), and
shear lag (U < 1)

87

Pu= Ry Fy Ag

Limit state: fracture of net section


(0.75) Ae (Rt Fu) ≥ Ry Fy Ag

For A500 Gr B rectangular HSS:


OR:

Need to Reinforce Net Section (Ae need not exceed Ag )

88

44
Also check block shear rupture of bracing member....

L t = design wall thickness of HSS

Pu= Ry Fy Ag

0.6 Anv Rt Fu
 Pn = (0.75) Ubs Ant Rt Fu + lesser of
0.6 Agv Ry Fy
Ant  0
Ant = Agv = 4 L t

For A500 Gr B rectangular HSS: Rt Fu = 1.3 x 58 ksi = 75.4 ksi


Ry Fy = 1.4 x 46 ksi = 64.2 ksi

89

Also check block shear rupture of bracing member....

L t = design wall thickness of HSS

Pu= Ry Fy Ag

 Pn = (0.75) ( 4 L t x 0.6 x 64.2 ksi) ≥ 1.4 x 46 ksi x Ag

= minimum length of welded overlap


needed based on block shear
rupture in HSS bracing member
panjang minimum tumpang tindih yang dilas diperlukan
berdasarkan pecahnya geser blok pada anggota
penyangga HSS

90

45
Reinforcing net section of bracing member....
apakah perlu menyambung dengan las. Ya perlu
sebab sambungan tersebut akan memperkuat dengan luasan nilai a

91

13.2 Members
13.2c Lateral Force Distribution

Along any line of bracing, braces shall be deployed


in opposite directions such that, for either direction
of force parallel to the bracing, at least 30 percent but
not more than 70% of the total horizontal force along
that line is resisted by braces in tension..
Di sepanjang garis penyangga apa pun, penyangga harus dikerahkan
ke arah yang berlawanan sedemikian rupa sehingga, untuk kedua arah
gaya sejajar dengan penyangga, setidaknya 30 persen tetapi tidak
lebih dari 70% dari total gaya horizontal di sepanjang garis itu ditahan
oleh penyangga dalam tegangan.

92

46

You might also like