Translated from Spanish to English - www.onlinedoctranslator.

com

CONFIGURATION OF RECTIFIER

FEBRUARY - 2023

John J.
CONTENT

· Chapter 1:Product Description

· Chapter 2:IP/Mask/Gateway Settings
· Chapter 3:Time and Date Settings
· Chapter 4:AC input type configuration
· Chapter 5:Battery type and capacity configuration
· Chapter 6:Battery recharge coefficient configuration
· Chapter 7:Input relay configuration
· Chapter 8:Output relay configuration
· Chapter 9:Installation of Lithium batteries in ZTE rectifier
· Chapter 10:BCUA (Lithium Battery Controller) Configuration
Chapter 1:Product Description 内部公开▲

© ZTE All rights reserved

3
UIB: 内部公开▲

© ZTE All rights reserved

4
 内部公开▲
Log in:
To enter through the CSU display we enter:

Equipment User Password

CSU 602A admin 0063
CSU 602A superman 3600
CSU 602A - website admin ZTEPower@0063

CSU 602A - website superman Supermanfly!

BCUA power ZTECorporation@0063

© ZTE All rights reserved

5
Chapter 2 : IP / Mask / Gateway Configuration
内部公开▲

1) On the controller manually switch to static mode (STATIC).

2) Change the IP on our computer and enter the IP provided by our

operator via the web.

© ZTE All rights reserved

6
Chapter 2 : IP / Mask / Gateway Configuration
内部公开▲

* ) Go to:

Parameter Settings > Network Parameters > Wired Connection:

Configure parameters assigned by operator and at the end we click on

ESTABLISH

© ZTE All rights reserved

7
 内部公开▲

Configure IP
supplied by Claro

Configure server IP:

172.19.216.107

Configure server IP:

172.19.216.107

Configure port
server:162

© ZTE All rights reserved

8
Chapter 3: Time and Date Settings 内部公开▲

© ZTE All rights reserved

9
Chapter 4 : AC input type configuration 内部公开▲

* ) Go to:

Setting parameters > AC > Parameter data:

Configure parameter according to AC supply, at the end we click on

ESTABLISH

© ZTE All rights reserved

10
Chapter 5: Battery type and capacity configuration 内部公开▲

© ZTE All rights reserved

11
 内部公开▲

© ZTE All rights reserved

12
Chapter 6: Battery recharge coefficient configuration 内部公开▲

© ZTE All rights reserved

13
Chapter 7: Input relay configuration 内部公开▲

Port of Relay Conf.

Alarm Description Level
entrance entrance

High ambient temperature / Too high MAJOR/IMPORTANT X7 (Temp Send) UIB_X7_T4

Battery door open CRITICAL X3 (input RLY 1) UIB_X3_DI1

© ZTE All rights reserved

14
 内部公开▲
High ambient temperature / Too high

© ZTE All rights reserved

15
 内部公开▲
Battery door open

© ZTE All rights reserved

16
Chapter 8: Output relay configuration 内部公开▲

Alarm Description Level Port of entry Input Relay Conf. Output Relay

AC failure CRITICAL N/A N/A UIB_X2_DO1

Rectifier Failure CRITICAL N/A N/A UIB_X2_DO2

LLVD1/LLVD2 drop CRITICAL N/A N/A UIB_X2_DO3

Low Battery Voltage / Too Low MAJOR/IMPORTANT N/A N/A UIB_X2_DO4

Rectifier door open MAJOR/IMPORTANT X8 (Door) N/A UIB_X1_DO5

High ambient temperature / Too high MAJOR/IMPORTANT X7 (Temp Send) UIB_X7_T4 UIB_X1_DO6

Battery door open CRITICAL X3 (input RLY 1) UIB_X3_DI1 UIB_X1_DO7

Broken air conditioning CRITICAL X14 (input RLY 5) N/A UIB_X1_DO8

© ZTE All rights reserved

17
 内部公开▲

© ZTE All rights reserved

18
AC failure
内部公开▲

© ZTE All rights reserved

19
Rectifier Failure 内部公开▲

© ZTE All rights reserved

20
LLVD1/LLVD2 Drop (Loads) 内部公开▲

© ZTE All rights reserved

21
 内部公开▲
Dropout of LLVD1/LLVD2 (Batteries)

© ZTE All rights reserved

22
Low Battery Voltage / Too Low 内部公开▲

© ZTE All rights reserved

23
Rectifier door open 内部公开▲

© ZTE All rights reserved

24
High ambient temperature / Too high
内部公开▲

© ZTE All rights reserved

25
Battery door open 内部公开▲

© ZTE All rights reserved

26
Broken air conditioning 内部公开▲

© ZTE All rights reserved

27
Chapter 9: Installation of Lithium batteries in ZTE rectifier
内部公开▲

1. Configure battery dip switch according to the order of the

batteries.
2. Connect the 485 communication cables.
3. Connect the PE port to ground.
4. Turn on the lithium batteries from the On button.
5. Connect batteries to the rectifier breaker or terminal bar

OFF

BATTERY 1

BATTERY 2

BATTERY 3

BATTERY 4

BATTERY 5

BATTERY 6

© ZTE All rights reserved

28
 内部公开▲

ZTE Lithium Battery Voltage Float Volt. Float.

Model Range Recommended

FB100C2 52.5V ‒ 54.0V 52.5V

FB100B3 53.5V ‒ 58V 54.5V

© ZTE All rights reserved

29
 内部公开▲

On/Off button

Dip switch

Battery communication
485

PE Port Grounding Func

Anti-Theft

© ZTE All rights reserved

30
 内部公开▲

Bat 16

Bat 3
The RS485 port must be used
to interconnect the batteries.

Bat 2

Bat 1

© ZTE All rights reserved

31
 内部公开▲

Port Management

© ZTE All rights reserved

32
 内部公开▲
Chapter 9: Installation of Lithium batteries in ZTE rectifier

© ZTE All rights reserved

33
Chapter 10: BCUA (Lithium Battery Controller) 内部公开▲

Configuration

Power input interfaces Indicators

Communication interfaces Ethernet port 4G Antenna interface

Grounding terminal

© ZTE All rights reserved

34
 内部公开▲

BCUA connected to FB100 B3 lithium batteries

· Connect the cables of

communication according to what

shown in the figure.

· The resistors must be connected
in the last battery and in the port

BCUA HL.
· Connect the PE port to the busbar
land.
· Connect the batteries to the breakers
of the power core.

© ZTE All rights reserved

35
BCUA operation 内部公开▲

Via a connected network cable

directly
1. Use a network cable to connect your PC

directly to the network interface of the

BCUA.

2. Turn on the PC. Select Start > Dashboard

Control > Network and Internet > Network

and Shared Resource Center >

Local Area Connection > View your networks

active.
3. Click Properties. double
click Internet Protocol version 4
(TCP/IPv4).

© ZTE All rights reserved

36
BCUA operation 内部公开▲

4. On the General tab, click

Use the following IP address and

configure the parameters. The

IP address should be similar to

192.168.1.5. The subnet mask

should be 255.255.255.0. The door

Default binding should be

192.168.1.1. After the
modification, click OK
to save the modification.

© ZTE All rights reserved

37
BCUA operation 内部公开▲

Through the Web Portal - steps

1. Log in to the web portal using the Chrome browser. The username is Power and the
password can be obtained from your local ZTE representative office. After logging in for the first
time, change the password to a secure one. The login page is displayed

© ZTE All rights reserved

38
BCUA operation 内部公开▲

© ZTE All rights reserved

39
BCUA operation 内部公开▲

We change the following parameters:

Local IP Mode:static

Local IP Addresses / Mask / Gateway These

static
parameters must be supplied by the
network administrator's planning.

© ZTE All rights reserved

40
BCUA operation 内部公开▲

Upon completing the configuration of the IP provided by the provider, we verify if the IP has been
correctly changed. For this, as step 1, we change the IP of our computer following the steps
indicated at the beginning and we assign ourselves an IP within the segment that the operator
gives us. In this example the operator assigned us the IP 10.32.32.193 mask 255.255.255.216

So on our computer we have assigned ourselves the IP 10.32.32.194 Mask

255.255.255.216

© ZTE All rights reserved

41
BCUA operation 内部公开▲

As step 2 we open a command prompt manager and ping the address assigned to
us by our operator:

ping 10.32.32.193
We must obtain a response as shown in the image, otherwise the IP has not been
changed and the steps must be repeated again from the beginning.

© ZTE All rights reserved

42
 内部公开▲

Number of batteries
connected, in this case 6
lithium batteries connected State:In download(discharge).

© ZTE All rights reserved

43
Thanks！