S AVOY

G L A Z E D C E R AM I C & PO RC E L A I N WA LL & FLO O R T I LES

C O LO U R C O N C RET E S E LEC T

www.johnson-tiles.com
 S AVOY
19 COLOU RS 3 S I Z ES 2 FI N IS H ES

The Savoy Wall and Floor tile ranges provide a contemporary and stylish offering.
The Savoy wall glazed ceramic tiles are made right here in the UK and are available in two
small-format, metro sizes of 200x100mm and 300x100mm. Combine this with the
Savoy Floor glazed porcelain 200x200mm square tiles, suitable for both floor & wall use and
with a PTV slip resistance rating of 36+, to complete the look.
Savoy Wall delivers stunning depth of colour across fifteen tones from the muted Luna to
vibrant Marine, also with a gloss décor option available in every colour and a selection of
co-ordinating fittings. Perfectly teamed with the co-ordinating colour palette of the Savoy Floor,
featuring a rustic concrete effect field tile and a selection of modern geometric patterns. Each of
the designs are dynamic and bold and can be used alone or as part of a patchwork for visual interest.
The possibilities are endless when marrying the understated tones of the Savoy Wall with the
timeless patterning of the Savoy Floor, adding character and individuality to any interior.

02
Sage Gloss 200x100x6.5mm - SAV09A
Noir Gloss Chair Rail C 200x35x30mm - SAV07A
Noir Gloss Atlas Skirting 200x150x20mm - SAV07A
Noir Gloss Finishing Strip 200x12x8mm - SAV07A

03
 Pebble Gloss 300x100x8mm - SAV11A
Pebble Gloss Geometric 300x100x8mm - SAV11D

Steel Gloss 300x100x8mm - SAV06A

Slate Gloss Chair Rail C 200x35x30mm - SAV12A

04
Sage Gloss 200x100x6.5mm - SAV09A
Slate Gloss 200x100x6.5mm - SAV12A Caraway Gloss 300x100x8mm - SAV04A

Noir Gloss 300x100x8mm - SAV07A

Noir Gloss Geometric 300x100x8mm - SAV07D
Steel Gloss 300x100x8mm - SAV06A

05
 Marine Gloss 300x100x8mm - SAV15A
Marine Gloss Geometric 300x100x8mm - SAV15D

Bone Gloss 300x100x8mm - SAV10A

06
 Noir Gloss 300x100x8mm - SAV07A

Sage Gloss 300x100x8mm - SAV09A

Noir Gloss Chair Rail C 200x35x30mm - SAV07A
Noir Gloss Atlas Skirting 200x150x20mm - SAV07A
Concrete Natural 200x200x8.5mm - SAVF1N
Concrete Décor Natural 200x200x8.5mm - SAVF1D

07
 Size Formats
Sizing & Packing Information

1
1

2
2 3

3
4

# Size Thickness Finish Structure Pcs / Box M2 / Box Kg / Box

- 34 Tiles 1.02 m2 14.00 kg
1 300x100mm 8mm G Gloss
Geometric 34 Tiles 1.02 m2 14.00 kg

2 200x100mm 6.5mm G Gloss - 50 Tiles 1.00 m2 11.50 kg

3 200x200mm 8.5mm N Natural - 26 Tiles 1.04 m2 19.00 kg

# Fitting Thickness Finish Pcs / Box LM / Box Kg / Box

1 200x150mm Atlas Skirting 6.5mm - 20mm G Gloss 8 Tiles 1.60 lm 8.78 kg

2 200x75mm Chair Rail A 6.5mm - 30mm G Gloss 14 Tiles 2.80 lm 7.70 kg

3 200x35mm Chair Rail C 6.5mm - 30mm G Gloss 28 Tiles 5.60 lm 5.00 kg

4 200x12mm Finishing Strip 6.5mm - 8mm G Gloss 50 Tiles 10.00 lm 1.04 kg

5 300x14mm Finishing Strip 8mm - 10mm G Gloss 30 Tiles 9.00 lm 0.80 kg

Note: 300x100mm, 200x100mm and All Fitting Options are glazed ceramic [BIII], and are suitable for internal wall applications only. 200x200mm are glazed porcealin [BIa],
and are suitable for internal and external wall and internal floor applications. All sizes indicated are metric modular. All sizes shown are nominal.
For the most up-to-date size, colour and finish availability, please visit our website - www.johnson-tiles.com.

Luna Gloss 200x100x6.5mm - SAV01A

Luna Gloss Chair Rail A 200x75x30mm - SAV01A

08
 Colours & Product Codes [BIII]
V3: Moderate to High Shade Variation

LU N A LRV: 73 LU N A LRV: 73 OAT LRV: 62 OAT LRV: 62

Product Code: Geometric Product Code: Product Code: Geometric Product Code:
G SAV01A G SAV01D G SAV02A G SAV02D

GRAIN LRV: 42 GRAIN LRV: 42 C A R AWAY LRV: 29 C A R AWAY LRV: 29

Product Code: Geometric Product Code: Product Code: Geometric Product Code:
G SAV03A G SAV03D G SAV04A G SAV04D

N.B. All colour-ways shown on this page (excluding Geometrics) are available
in 300x100mm and 200x100mm size formats, plus All Fitting Options. Key to Finishes: G Gloss N Natural 09
 Colours & Product Codes [BIII]
V3: Moderate to High Shade Variation

D EW LRV: 50 D EW LRV: 50 ST E E L LRV: 31 ST E E L LRV: 31

Product Code: Geometric Product Code: Product Code: Geometric Product Code:
G SAV05A G SAV05D G SAV06A G SAV06D

NOIR LRV: 06 NOIR LRV: 06 LE A F LRV: 42 LE A F LRV: 42

Product Code: Geometric Product Code: Product Code: Geometric Product Code:
G SAV07A G SAV07D G SAV08A G SAV08D

N.B. All colour-ways shown on this page (excluding Geometrics) are available
10 Key to Finishes: G Gloss N Natural in 300x100mm and 200x100mm size formats, plus All Fitting Options.
 Colours & Product Codes [BIII]
V3: Moderate to High Shade Variation

S AG E LRV: 32 S AG E LRV: 32 BO N E LRV: 55 BO N E LRV: 55

Product Code: Geometric Product Code: Product Code: Geometric Product Code:
G SAV09A G SAV09D G SAV10A G SAV10D

P E B B LE LRV: 20 P E B B LE LRV: 20 S L AT E LRV: 22 S L AT E LRV: 22

Product Code: Geometric Product Code: Product Code: Geometric Product Code:
G SAV11A G SAV11D G SAV12A G SAV12D

N.B. All colour-ways shown on this page (excluding Geometrics) are available
in 300x100mm and 200x100mm size formats, plus All Fitting Options. Key to Finishes: G Gloss N Natural 11
 Colours & Product Codes [BIII]
V3: Moderate to High Shade Variation

P ET RO L LRV: 15 P ET RO L LRV: 15 INK LRV: 20 INK LRV: 20

Product Code: Geometric Product Code: Product Code: Geometric Product Code:
G SAV13A G SAV13D G SAV14A G SAV14D

M A RI N E LRV: 35 M A RI N E LRV: 35 Ink Gloss 300x100x8mm - SAV14A

Ink Gloss Geometric 300x100x8mm - SAV14D
Product Code: Geometric Product Code:
G SAV15A G SAV15D

N.B. All colour-ways shown on this page (excluding Geometrics) are available
12 Key to Finishes: G Gloss N Natural in 300x100mm and 200x100mm size formats, plus All Fitting Options.
Steel Gloss 200x100x6.5mm - SAV06A

13
 Colours & Product Codes [BIa]
V2: Low to Moderate Shade Variation

C O N C RET E PEI: IV C O N C RET E D ÉC O R PEI: IV

Product Code: N SAVF1N Product Code: N SAVF1D

G REY S Q UA RE D ÉC O R PEI: IV B E I G E S Q UA RE D ÉC O R PEI: IV

Product Code: N SAVF1S Product Code: N SAVF2S

Concrete Natural 200x200x8.5mm - SAVF1N

N.B. All colour-ways shown on this page are

14 Key to Finishes: G Gloss N Natural available in 200x200mm size format only.
 Colours & Product Codes [BIa]
V2: Low to Moderate Shade Variation

B LU E M I X D ÉC O R PEI: IV

Product Code: N SAVF3M

Note: Each box of SAVF3M Blue Mix Décor Natural 200x200x8.5mm contains a random selection of all four designs shown above.

Marine Gloss 200x100x6.5mm - SAV15A

Marine Gloss Atlas Skirting 200x150x20mm - SAV15A
Concrete Natural 200x200x8.5mm - SAVF1N
Concrete Décor Natural 200x200x8.5mm - SAVF1D
Blue Mix Décor Natural 200x200x8.5mm - SAVF3M

N.B. All colour-ways shown on this page are

available in 200x200mm size format only. Key to Finishes: G Gloss N Natural 15
 Technical, Sustainability
& Important Information

Specification

Range Finish Wall Suitability Floor Suitability Wet Barefoot CSV Material
G Gloss Internal Only - - V3 Glazed Ceramic [BIII]
Savoy
N Natural Internal & External Internal Only - V2 Glazed Porcelain [BIa]

Floor Values

Finish Structure PTV (4S) PTV (TRL) R Value Wet Ramp PEI Traffic
N Natural - Dry 36+ Wet 36+ - - - IV Commercial

Physical Properties - Glazed Ceramic [BIII]

Test & Standard Requirement Test Result Test & Standard Requirement Test Result
Length / Width Modulus of Rupture
± 0.5% ≤ ± 2mm ≤ ± 0.25% Min. 15N / mm2 ≥ 25N / mm2
EN ISO 10545 - 2 EN ISO 10545 - 4
Thickness Thermal Shock
± 10% ≤ ± 0.5mm ± 2.5% Pass Pass
EN ISO 10545 - 2 EN ISO 10545 - 9
Straightness of Side Frost Resistance
± 0.3% ≤ ± 1.5mm ± 0.15% - Not Suitable
EN ISO 10545 - 2 EN ISO 10545 - 12
Rectangularity Chemical Resistance
± 0.5% ≤ ± 2mm ± 0.4% Min. Class B Class A - B
EN ISO 10545 - 2 EN ISO 10545 - 13
Surface Flatness Stain Resistance
± 0.5% ≤ ± 2mm ± 0.3% Min. Class 3 Class 3
EN ISO 10545 - 2 EN ISO 10545 - 14
Water Absorption Class A1
10% to 20% 15% to 17% Fire Rating -
EN ISO 10545 - 3 Non Combustible
kg 17.50 kg 11.70 kg
Weight / M2
8mm thick 6.5mm thick

Physical Properties - Glazed Porcelain [BIa]

Test & Standard Requirement Test Result Test & Standard Requirement Test Result
Length / Width Modulus of Rupture
± 0.6% ≤ ± 2mm ± 0.35% Min. 35N / mm2 ≥ 52N / mm2
EN ISO 10545 - 2 EN ISO 10545 - 4
Thickness Thermal Shock
± 5% ≤ ± 0.5mm ± 1.5% Pass Pass
EN ISO 10545 - 2 EN ISO 10545 - 9
Straightness of Side Frost Resistance
± 0.5% ≤ ± 1.5mm ± 0.1% Resistant Resistant
EN ISO 10545 - 2 EN ISO 10545 - 12
Rectangularity Chemical Resistance
± 0.5% ≤ ± 2mm ± 0.4% Min. Class B Pass
EN ISO 10545 - 2 EN ISO 10545 - 13
Surface Flatness Stain Resistance
± 0.5% ≤ ± 2mm Pass Min. Class 3 Class 5
EN ISO 10545 - 2 EN ISO 10545 - 14
Water Absorption Class A1 FL
≤ 0.5% ≤ 0.1% Fire Rating -
EN ISO 10545 - 3 Non Combustible
kg 18.50 kg
Weight / M2
8.5mm thick

Sustainability Information
Recycled Content Recycled Content Recyclable Content
Range Material EPD of the Tiles of the Packaging of the Packaging
Glazed Ceramic [BIII] Yes Up to 20% Up to 100% Up to 100%
Savoy
Glazed Porcelain [BIa] - Up to 50% Up to 100% -

Note: Due to the manufacturing process of all floor tiles there may be small variations in slip resistance. Given this, please refer to our website for the most up-to-date information.
The slip resistance properties of a surface can only be maintained with the implementation of an effective regular cleaning and maintenance regime. The frequency of cleaning
should be determined by the property manager based on the potential level of surface contaminants. The need for an additional regular cleaning and maintenance regime is further
heightened when tiles are used for external floor and wet barefoot applications.
Please contact our technical helpline for specification and installation advice. All glazed ceramic [BIII] and glazed porcelain [BIa] products shown in this sample tile wallet conform
to BS EN 14411. CSV: Colour Shade Variation. PTV (4S): Pendulum Test Value - Slider 96. PTV (TRL): Pendulum Test Value - Slider 55. R Value (DIN 51130). Wet Ramp (DIN 51097).
PEI: Porcelain Enamel Institute.
For a full overview of our environmental credentials please visit www.johnson-tiles.com/about/sustainability. EPD: Environmental Product Declaration.

Important Information
During the manufacturing process of ceramic and porcelain tiles, some variation
in shade and pattern can occur. Before fixing any tiles; several boxes should be
opened and their contents mixed to ensure that size, colour, shade and patterning
are acceptable. The tiles shown are quality products and conform to the physical
properties listed. For a comprehensive colour, size and finish overview along
with full technical and sustainability information for all of the product shown
in this product presenter, please visit our website - www.johnson-tiles.com. All product technical values quoted in this product presenter are supported by laboratory
testing from our own and independent ceramic test houses. Johnson Tiles are British
• All sizes shown are metric modular. Standard registered and all products conform to the standards set in BS EN 14411.
• For specific suitability details please contact our technical department. For the reassurance of single-source supply, Johnson Tiles offers a free of charge NBS
M40 specification writing service featuring the Norcros Adhesives range of tile fixing
• Johnson Tiles cannot accept responsibility for tiles that have been fixed. products. To find out more or for any questions or queries relating to any tile related
• Every effort has been made to ensure the accuracy of the information given. technical information featured in this product presenter, please contact our technical
advice helpline on +44 (0)1782 524 111 or email [email protected]
• Johnson Tiles reserves the right to change specification and availability
information without prior notice. The colours shown in this sample tile wallet and attached booklet are as accurate as
printing processes will allow. Please refer to actual product samples before specifying.
• Nothing in these statements does/will affect the statutory rights of the consumer. Every effort has been made to ensure the accuracy of the information given.

® Johnson Tiles, Johnson, Absolute and Material Lab are registered trademarks and together with Kerastar and product names are the trademarks of H&R Johnson Tiles Limited and
licensed to Norcros Group (Holdings) Limited trading as Johnson Tiles. © 2023 Johnson Tiles. All rights reserved.

16
Installation Advice
Codes of Practice straight-edge, any gap under the straight-edge Porcelain Tiles (BIa)
All fixing of floor and cladding tiles should be in between points of contact does not exceed 3mm”.
accordance with the following codes of practice Substrate Product
guidelines:
Movement Joints Concrete Rapid Porcelain / Flexible
BS5385 Part 1 - 2018 The location, type and scope of all movement joints Sand / Cement Screed Rapid Porcelain / Flexible
Design and installation of internal ceramic, natural must be ascertained prior to any fixing works. All
structural joints must be followed through to the face Wood Floors Rapid Porcelain / Flexible*
stone and mosaic wall tiling in normal conditions.
of the tile at full width with intermediate movement Brick / Blockwork Rapid Porcelain / Flexible
BS5385 Part 2 - 2015 joints (minimum 6mm wide) being situated at:
Design and installation of external ceramic, natural Plaster Gypsum Rapid Porcelain / Flexible
stone and mosaic wall tiling in normal conditions. Changes of Plane (Incl. Wall Corners) Plasterboard Rapid Porcelain / Flexible**
BS5385 Part 3 - 2014 Wall / Floor Junctions
Design and installation of internal and external * Overlay with minimum 15mm WBP / Marine Ply
ceramic and mosaic floor tiling in normal conditions. Where Tiling Abuts Other Materials and Prime using Norcros Adhesive Prime and Seal.
** Prime using Norcros Adhesive Prime and Seal.
BS5385 Part 4 - 2015 Additionally at 3 to 4.5m maximum centres for wall
Design and installation of ceramic and mosaic tiling tiling and 8 to 10m maximum bay centres for floor
in specific conditions. tiling (in suspended floors the bay dimensions should Grouts
BS5385 Part 5 - 2009 be reduced by providing additional joints over The choice of grout type should reflect the expected
Design and installation of terrazzo, natural stone, supporting walls and beams). service conditions of the installation.
and agglomerated stone tile and slab flooring.
Movement joints can either be filled with a suitable For general internal wall tiling in dry conditions and
BS8000 Part 11 - 2011 backer, bond breaker and filler (e.g. silicone for walls walls subject to frequent wetting i.e. showers and pool
Workmanship on building sites. Internal and external wall tiles only or epoxy polysulphide for floor and wall halls, use Norcros Adhesives 4 in 1 Cement Based
and floor tiling. Ceramic and agglomerated stone tiles, tiles – please check with manufacturer for suitability) Grout - classified as CG2.
natural stone and terrazzo tiles and slabs and mosaics. or be of the pre-formed variety.
For walls where hygiene is important i.e. commercial
BIII (Ceramic) tiles smaller than 400x300mm require kitchens and hospitals, use Norcros Adhesives Super
the use of an adhesive with a D1 or D2 classification. Design / Layout
Epoxy Grout - classified as RG1.
Larger tiles require an adhesive with C2 classification. Consideration to locations of plane changes and room
sizes should be undertaken to ensure the best tile size For general floor tiling use Norcros Adhesives 4 in 1
BIa (Porcelain) tiles require the use of a polymer is selected to minimise cutting and improve aesthetics. Flexible Wall and Floor Tile Grout - classified as CG2.
modified adhesive with a classification of C2* and
grouts specifically formulated for the fixing and For floors subject to frequent wetting i.e. showers
Adhesives
grouting of porcelain tiles. and pool halls, use Norcros Adhesives 4 in 1 Flexible
Adhesives should be in accordance with BS EN 12004,
Wall and Floor Tile Grout - classified ad CG2 (hard
* Check with the adhesive manufacturer for additional Class D1 or D2 for ceramic tiles and Class C2 or C1*
water areas) or Norcros Adhesives Super Epoxy
C1 product suitability. for porcelain tiles. Particular adhesive choice will be
Grout - classified as RG1 (soft water areas).
governed by the type of substrate.

Substrates * Check with the adhesive manufacturer for additional For specific adhesive and grout advice, please
Before tiling is commenced it is important to ensure C1 product suitability. contact Norcros Adhesives technical helpline
that the correct minimum curing periods have been on +44 (0)1782 524 140.
observed for all substrates: Johnson Tiles recommends the use of Norcros
Adhesives products - see below:
Fixing Tiles
Concrete (6 Weeks)
All tiles should be fixed with a solid bed of adhesive,
Screed - Non Modified (3 Weeks ) Ceramic Tiles (BIII) this ensures maximum durability and strength within
Rendering - Non Modified (2 Weeks) the installation and long term adhesion performance.
Substrate Product This is achieved with the use of a notched solid bed
Gypsum Plastering (4 Weeks) trowel. It is good practice to periodically remove a
Brickwork / Blockwork (6 Weeks) Concrete One Part Flexible recently fixed tile to ensure that the correct bedding
Sand / Cement Screed One Part Flexible is being achieved and maintained. When fixing all tiles
Accuracy of the substrate must be checked to ensure care must be taken to ensure that no lipping of tiles
Brick / Blockwork One Part Flexible
that the guidance given in BS5385 has been achieved occurs.
i.e. “local variations in level for a nominally flat floor Plaster Gypsum One Part Flexible
or wall should be such that, when checked with a 2m Plasterboard One Part Flexible All tiles shown in this brochure are recommended
to be fixed with a nominal 3mm wide joint.

Cleaning and Maintenance

Maintaining the appearance and characteristics Epoxide Grouts High Pressure Cleaning
(especially slip resistance values) of floor tiles is It is essential that ALL residue must be removed Tiles seldom require the use of high-pressure
achieved with the implementation of a suitable cleaning from the surface of the tiles during the grouting cleaning. Whilst the process will not damage the
regime. It must be stressed that the cleaning material process and before the resin cures. Failure to achieve tiles care must be taken to avoid erosion of the grout.
manufacturers instructions must be followed at all this will result in a very difficult and expensive To minimise grout erosion ensure that the water
times. Regular and correctly undertaken cleaning process using gel-type epoxide removers. beam is continually moved from side to side and not
should maintain a flooring product as close to its allowed to concentrate on the grouted joints. Water
original state as possible. Incorrect or infrequent containing abrasives or steam cleaners should not
cleaning will adversely affect the properties of the Routine Cleaning be used on ceramic tiles.
flooring material and increase potential hazards. The regular use of detergents or other cleaning
Generally the smoother the surface of the tile the agents, which are excessively acidic or alkaline could
easier it is to clean. However, it should be noted that cause irreversible damage to the ceramic tile surface. Wet Areas
textured products, required to give adequate slip Degreasing agents that contain wax, sodium silicate or Wet barefoot areas may attract build-ups of body
resistance when wet, can be satisfactorily cleaned – other additives which leave sticky deposits and thus fats, soaps, oil residues and organic growth. To
the cleanability of a surface is more a function of the retain dirt should be avoided. Oil residues or build-ups prevent these a mildly acidic cleaning agent used
contaminant than the texture of the surface. It is of wax can be removed with a proprietary wax and regularly is preferable. If build-up has been allowed
therefore essential when selecting and specifying a polish remover. a preliminary deep clean with a proprietary cleaner is
floor finish that the use of the area and likely required followed by regular use of a mildly acidic
contaminants, safety, aesthetic and hygiene requirements cleaning agent solution.
Manual Cleaning
are all taken into account at the specification stage. In normal conditions tiles require little maintenance
and can be easily kept clean by sweeping and then Periodic Deep Cleaning
Cleaning can be split into several categories, each of
mopping with warm water to which a neutral or Occasionally foreign matter may cause surface marks
which is dependant upon installation type (i.e. wet
nearly neutral detergent has been added. The cleaning that cannot be removed with the usual cleaning
barefoot areas, shopping malls, public toilets, etc.) and
solution should remain on the floor for 5 to 15 processes and materials. If the surface mark cannot be
frequency of usage (i.e. high, medium or low traffic):
minutes (see manufacturers instructions) to allow it removed, other materials should be considered (it’s
to penetrate and emulsify the dirt after which it advisable to experiment on a small inconspicuous area):
Builders Clean should be removed by rinsing thoroughly with clean
This should be undertaken before a floor is being water. The rinsing process removes the dirt so the Paint - Paint Remover
brought into service. The builders clean removes any use of clean water is important. Organic Stains - Bleach / Washing Soda
residual film leftover from the grouting operation and
Rust - Masonry Cleaner
is a one-off cleaning process. This must be carried out
Mechanical Cleaning Oil / Fat / Grease - Detergent or Degreaser
as any grout residues left behind will act as a key for
For larger floor areas or areas of textured tiles the
dirt resulting in the installation being difficult to clean. Mould Growth - Bleach / Proprietary Cleaner
use of a rotary scrubbing machine is recommended
Temporary sealers may be used to facilitate cleaning
(machines should not be used at speeds in excess of Tea / Coffee / Ink - Bleach / Proprietary Cleaner
off after laying which can be removed with the use of
450rpm). The choice of brush type is very important.
alkaline detergents. Abrasive powders or cleaners should never be used on
Union mix brushes are suitable for light washing and
scrubbing, polypropylene brushes are suitable where glazed or polished tiles.

Cementitious Grouts dirt deposits are especially heavy. The cleaning solution
The use of a mild acid de-cementing solution should remain on the floor for 5 to 15 minutes (see
followed by thorough rinsing will remove all but manufacturers instructions) after which a secondary
the most stubborn of cement residues. scrubbing action and clean mop or suction should be
undertaken to remove the solution and dirt.

17
 For more information about Savoy or any
of our other product ranges simply visit
www.johnson-tiles.com

Where To Find & Contact Us

Johnson Tiles Head Office
Harewood Street, Tunstall,
Stoke on Trent, Staffordshire,
ST6 5JZ, United Kingdom
Tel: +44 (0)1782 575 575
Email: [email protected]
www.johnson-tiles.com

Material Lab Studio

10 Great Titchfield Street,
London, W1W 8BB,
United Kingdom
Tel: +44 (0)20 7436 8629
Email: [email protected]
www.material-lab.co.uk

Johnson Tiles Factory Outlet

Tel: +44 (0)1782 524 040
Email: [email protected]
www.outlet.johnson-tiles.com

Customer Services
Tel: +44 (0)1782 524 000
Email: [email protected]

Order A Sample
Tel: +44 (0)1782 524 043
Email: [email protected]

Technical Advice
Tel: +44 (0)1782 524 111
Email: [email protected] Johnson Tiles is a division of Norcros Group (Holdings) Limited,
Ladyfield House, Station Road, Wilmslow, Cheshire, SK9 1BU,
Launched: October 2013 Updated: May 2023 United Kingdom. Registered in England number 566694.