Accessory Application Publications No.

INSTALLATION USB ADAPTER 2010 FIT

AII 42219

(BASE MODEL) Issue Date

INSTRUCTIONS AUG 2009

PARTS LIST 4 Wire ties

USB Adapter Attachment Kit
P/N 08B28-TK6-100
Right bracket

4 Washer-screws

Left bracket

Urethane tape

USB cord

USB Adapter Kit

P/N 08A28-0K1-100
Control unit
Bus cable

Cord holder

2 Flange bolts

© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42219 (0908) 08B28-TK6-1000-91 1 of 6
TOOLS AND SUPPLIES REQUIRED 3. Remove the passenger’s under cover (three clips
and two tabs).
Phillips screwdriver
Flat-tip screwdriver
Ratchet
8 mm and 10 mm Sockets
10 mm Combination wrench
Diagonal cutters
Utility knife
Scissors
Masking tape
Plastic Trim Tool T/N SILTRIMTL10
KTC trim tool set SOJATP2014*
* Available through the Honda Tool and Equipment
Program; call 888-424-6857.
3 CLIPS
Illustration of the USB Adapter installed on the
2 TABS
Vehicle PASSENGER’S
UNDER COVER

4. Remove the lower glove box (two screws, and

release the two stoppers).
BUS CABLE CONTROL
UNIT
2 STOPPERS

USB CORD
CORD HOLDER

INSTALLATION LOWER
GLOVE BOX

Customer Information: The information in this SCREWS

installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”

1. Make sure you have the anti-theft code for the audio
unit and navigation system (if equipped), then write
down the audio presets.
2. Disconnect the negative cable from the battery.

2 of 6 AII 42219 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
5. Inside the upper glove box, remove the side cover 7. Slide the vent lever to the right. Remove the center
(four tabs). panel screw. The screw can be located by looking
through the glove box opening. The screw is near
UPPER BOX LID the right side of the center panel.
Open.
CENTER LOWER LEVER LOWER GLOVE
COVER OPENING Slide. BOX OPENING

4 TABS SCREW
SIDE COVER

6. Remove the center lower cover (three clips).

SIDE VIEW
BOTTOM VIEW
8. Attach masking tape to the instrument panel in the
area shown.
3 CLIPS
13 CLIPS MASKING VEHICLE CONNECTORS
TAPE
INSTRUMENT
PANEL

CENTER
LOWER
COVER

PLASTIC CLIP
REMOVER
SCREW
CENTER
LOWER
COVER
OPENING

PLASTIC TRIM
CENTER PANEL TOOL
9. Remove the one screw. Using a plastic trim tool, pull
the center panel out toward you to release the 13
clips. Unplug the vehicle connectors to remove the
center panel.

© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42219 (0908) 3 of 6
10. Get the USB cord. Wrap one urethane tape around 12. Install the control unit to the audio unit using two
the USB cord in the area shown. flange bolts.

URETHANE TAPE

AUDIO UNIT

GRAY TAPE

GRAY TAPE CONTROL

UNIT

CENTER
USB CORD PANEL
FLANGE BOLT

11. Install the left and right brackets to the control unit as 13. Plug the bus cable into the control unit and into the
shown using four washer-screws. audio unit.

4 WASHER-
SCREWS
AUDIO UNIT

CONTROL
UNIT

CONTROL
LEFT UNIT
RIGHT BRACKET
BRACKET
BUS CABLE

4 of 6 AII 42219 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
14. Route the USB cord through the center dashboard 18. Route the USB cord up into the upper glove box
opening as shown. opening. Insert the USB cord through the cord holder
as shown, and seat the grommet into the cord
2 WIRE TIES CENTER
holder.
GRAY TAPE DASHBOARD
GRAY CLIP OPENING
TAPE UPPER GLOVE
BOX OPENING
USB CORD GROMMET

USB
CORD

VEHICLE
HARNESS
CLIP

15. Using two wire ties, secure the USB cord to the CORD
vehicle harness in the areas shown. HOLDER
USB CORD GROMMET
16. Route the USB cord through the lower glove box
opening as shown. 19. Install the cord holder into the upper glove box in
place of the side cover and insert the end of the USB
LOWER GLOVE cord into the cord holder.
BOX OPENING

UPPER GLOVE
BOX OPENING

USB CORD
WIRE TIE GRAY
TAPE
GRAY
TAPE VEHICLE WIRE TIE
HARNESS
CORD
17. Using two wire ties, secure the USB cord to the USB CORD HOLDER
vehicle harness in the areas shown.

© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42219 (0908) 5 of 6
20. With the center panel near the dashboard, plug the
USB cord connector into the control unit. Plug in all
the vehicle connectors and reinstall the center panel.

VEHICLE CONNECTORS USB CORD

CONNECTOR

CENTER PANEL

CONTROL BOLT
UNIT

21. Check that all wire harnesses and cables are routed
properly and that all connectors are plugged in.
22. Reinstall all removed parts.
23. Reconnect the negative cable to the battery.
24. Enter the anti-theft codes for the audio unit and
navigation systems (if equipped), then enter the
customer’s radio presets.
25. Reset the clock.
26. Turn the audio unit on. Set the mode to USB by
pressing AUX until “USB” is shown on the radio
display. If “USB NO DATA” is displayed, the unit is
working properly.

6 of 6 AII 42219 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.