Fusion Boom User Guide 23-07-2024
Fusion Boom User Guide 23-07-2024
User Guide
Important: The pTron "Fusion Boom" Bluetooth soundbar is set at 60% default volume. You can increase the volume
through the control panel on the speaker.
Bluetooth Mode: -
Bluetooth Version: Bluetooth 5.3
Bluetooth pairing name: "pTron Soundbar”
Just Turn on the Speaker. It will Automatically Connect to the Last Connected Device.
Note: The last connected device must be within 10 meters of the speaker and the Bluetooth function must be turned
on.
AUX Mode
i. Connect the device with the 3.5mm aux cable and the speaker will enter into the AUX mode with voice prompts.
TF/USB Mode
i. Use TF Card: Insert a TF card into the TF slot to activate the TF card mode
ii. Use a USB drive: Insert a USB stick or pen drive into the slot to activate the USB drive mode.
1 2 3 4
1.Play/Pause Button:
1. Press one time to play or pause music
2. Press two times to redial the last calling number
3. Long press for TWS mode
2.Minus Button:
1. One time press the button for previous song
2. Long press to decrease the volume
3. Plus Button:
1. One time press the plus button for next song
2. Long press to increase the volume.
4.Mode Button:
1. If a TF card/USB drive is already plugged into the speaker but you want to play a song via Bluetooth then just
press the Mode button to enable playback thru Bluetooth connected device. To switch back to playback from TF
card/USB drive, just press the Mode button again.
2. Single press the button to change mode. Long press for LED light changes & LED off.
FM mode: Press one time mode button “M” to change the Bluetooth mode to FM mode.
FM search: In FM mode, press & hold down Play/Pause button for 2s to automatically search for channels
Next Station: One time press the” +” button.
Previous Station: One time press the”-” button.
Note: The charging cable works as an FM antenna in FM mode, so it is mandatory to connect the charging
cable in FM mode.
LED lights: This speaker comes with 11 different LED light modes; you can customize the lights for perfect vibes.
1. Change the Led light mode: You can change the LED light by long pressing (2sec) the Mode “M” button.
2. Turn off these lights: Press & hold (2 sec) 12 times mode “M” button to turn off the LED lights.
How to establish a TWS connection?
1. Turn on both the devices, speaker in proximity of each other within 1m distance.
2. Select one of the devices and long-press the " " button. Both devices will pair with each other, and the
speaker will respond with a voice prompt.
3. In your phone, search for” pT Soundbar” and click on the same. Once the connection has been established the
two devices can play music simultaneously.
4. To disconnect TWS, kindly press the play/pause " " button.
5. Wish to establish a TWS connection again- Switch the mode back to Bluetooth Mode, then long press the " "
button. Both speakers will connect automatically.
Safety Precautions
Keep the device out of extreme heat and humidity or corrosive environment.
Play time may vary depending on personal habits.
Using incompatible USB cable or high voltage chargers can damage the product & void the product warranty.
We strongly recommend using a good quality DC5V-1A chargers & the USB cable included in the package.
Please don't over-charge the product as it will decrease the service life of battery.
Read all warnings on the product and in the operating instructions.
Don’t jam the ports such as charger port, LED port, etc.
It is recommended to utilize the product below the maximum volume in order to protect your hearing.
Please don’t open/temper the product or product’s battery.
Please keep the product out of children’s reach.
Dispose the product responsibly and adhere to your local authority guidelines.
Disclaimer: The color and specifications shown in or mentioned in the user manual may differ from the actual
product. Images shown are for representation purposes only. Other product logos and company names mentioned
herein may be trademarks or trade names of their respective owners.