Analog amplifier module

RE 30223
Version: 2013-01
Type VT-MSPA1-1, VT-MSPA1-10, VT-MSPA1-11 Replaces: 02.12

▶ Component series 1X

H6833_d

Features Contents

▶ Suitable for controlling direct operated proportional Features 1

pressure valves: Ordering code 2
– DBET-6X, Functional description 2
– DBEM...-7X, Block diagram 3
– (Z)DRE 6…-1X, Terminal assignment/device view 3
– 3DRE(M) 10...-7X, Technical data 4
– 3DRE(M) 16...-7X, Output characteristic curve 5
– ZDRE 10…-2X, Device dimensions 5
– (Z)DBE6...-2X, Project planning/maintenance instructions/
– DRE(M) 10, 25, 32-6X additional information 6
▶ Inverse-polarity protection of the operating voltage
▶ Differential input for command value voltage +10 V
▶ Ramp generator up and down can be set separately
▶ Zero point potentiometer
▶ 1 command value attenuator
▶ Characteristic curve generator
▶ Clocked power output stage
▶ LED display: • Ready for operation (green)
▶ Measuring sockets for: • Pressure command value
• Actual current value
▶ Dither generator with command value- and operating
voltage-dependent frequency

Bosch Rexroth AG, RE 30223, edition: 2013-01

2/6 VT-MSPA1-1... | Analog amplifier module

Ordering code

01 02 03 04 05
VT-MSPA1 – – 1X / V0 / *

01 Analog amplifier module VT-MSPA1

02 For controlling direct operated proportional pressure valves:

DBET-6X, DBEM...-7X 1
(Z)DRE 6…-1X 10
3DRE(M) 10...-7X,
3DRE(M) 16...-7X,
ZDRE 10…-2X, 11
(Z)DBE6...-2X,
DRE(M) 10, 25, 32-6X

03 Component series 10 to 19 (10 to 19: Unchanged technical data and pin assignment) 1X

04 Standard version V0

05 Further details in the plain text *

Functional description

Analog amplifier for controlling pressure valves without Clock generator: 12

electrical feedback. The modular design allows for simple In the clock generator (12), a frequency for the output
top hat rail mounting as is usual in control cabinets. stage adjusted to the command value is generated.
Command value input: 4 Power output stage: 11-14
The module amplifier is controlled by means of a standard Using the control output coming from the characteristic
command value signal 0 to +10 V. By means of the zero curve generator (10) and the clock frequency, the power
point trimmer (Zw) (6), a zero point offset can be corrected. output stage generates a PWM signal that is fed into the
Ramp generator: 5 solenoid. The solenoid current is recorded and, in the
In the ramp generator (5), the control output rise is limited. current controller (11), compared with the control output
Using the trimmer "t <" (7), the time for the increasing and the difference is compensated.
command value signal is set and using trimmer "t >" (8), the Fault recognition: 15
time for the decreasing command value voltage is set. The Monitors the solenoid conductors with regard to cable
adjustable time is part of the technical data. break and short circuit as well as over-current of the output
Characteristic curve generator: 10 stage. If there is an error, the green ready for operation
Using the trimmer "Gw" (9), the rated current of 1.6 A display goes out.
for the solenoid is set. In the characteristic curve genera-
tor (10), the command value signal is changed so that
a linear command value pressure characteristic
curve results.

Bosch Rexroth AG, RE 30223, edition: 2013-01

 Analog amplifier module | VT-MSPA1-1... 3/6

Block diagram

+UB 1 4
24 V 14
1 11 P
3
2 DC
T

0V DC 13
2 12 5

15 Power

6 7 8 I>
Zw F t< F t> F
GND 3
10
U 9
16
Gw W i
U
Command value
F
0...+10 V 6 4 5

1 Fuse 7 Potentiometer ramp up 13 Schmitt trigger

2 Suppressor diode 8 Potentiometer ramp down 14 Output stage
3 Power supply unit 9 Potentiometer Imax 15 Fault recognition
4 Command value input 10 Characteristic curve generator 16 Measuring socket
5 Ramp generator 11 Current controller Ⓕ On front side
6 Potentiometer zero point 12 Clock generator

Terminal assignment/device view

Terminal assignment Device view

Terminal 4 5 6 Potentiometer: "Gw" Pressure command value

1 +UB "Zw" Zero point
2 Ground Rexroth "t <" Ramp time up
3 –Ucommand VT-MSPA1-1 "t >" Ramp time down
4 Solenoid +
5 Solenoid – Sockets: "w" Pressure command value
Gw
6 +Ucommand "I" Actual current value
Zw
"⊥" Measurement zero
t<
t>

w I

1 2 3

RE 30223, edition: 2013-01, Bosch Rexroth AG

4/6 VT-MSPA1-1... | Analog amplifier module

Technical data
(For applications outside these parameters, please consult us!)

VT-MSPA1-1 VT-MSPA1-10 VT-MSPA1-11

Operating voltage UB 24 VDC +40 % –10 %
Operating range:
– Upper limit value uB(t)max 35 V
– Lower limit value uB(t)min 21 V
Power consumption Pmax < 50 VA
Current consumption Imax < 1.3 A
Fuse Is Electronic overload protection and SMD fuse (soldered in)
Inputs:
– Command value (differential input) Ucommand 0 to +10 V; Re = 100 kΩ
Outputs: Imin
– Solenoid current/solenoid resistance Imax 1.9 A; R20 = 5.5 Ω 1.9 A; R20 = 5.2 Ω 1.9 A; R20 = 5.5 Ω
– Frequency f 180 to 450 Hz 330 Hz ± 10 % 180 to 450 Hz
Setting ranges:
GW: Solenoid current I 100 mA…1.9 A
ZW: Zero point ±25 %
t >:
Ramp t 80 ms…5 s 210 ms…5 s 160 ms…5 s
t <:
Measuring sockets:
– Command value "w" U 0 to 10 V
– Actual current value "I" U 1 mV ≙ 1 mA solenoid current
Type of connection 6 screw terminals
Type of mounting Top hat rail TH 35–7.5 according to EN 60715
Protection class according to EN 60529 IP 20
Dimensions (W x H x D) 25 x 79 x 85.5 mm
Admissible operating temperature range ϑ 0 to +50 °C
Storage temperature range ϑ –25 to +85 °C
Ground m 0.15 kg

Notice:
For information on the environment simulation testing for the areas EMC (electromagnetic compatibility), climate
and mechanical load, see data sheet 30223-U.

Bosch Rexroth AG, RE 30223, edition: 2013-01

 Analog amplifier module | VT-MSPA1-1... 5/6

Output characteristic curve

1600

1400
1
Output current in mA →

1200

2
1000

800

600

400

200

0 10 20 30 40 50 60 70 80 90 100

Command value in % →

1= VT-MSPA1-1 and VT-MSPA1-11

2= VT-MSPA1-10

Device dimensions (dimensions in mm)

4 5 6

Rexroth
VT-MSPA1-1

Gw
Zw
79

t<
t>

w I

1 2 3

85,5 25

RE 30223, edition: 2013-01, Bosch Rexroth AG

6/6 VT-MSPA1-1... | Analog amplifier module

Project planning/maintenance instructions/additional information

▶ The amplifier module may only be wired when de-energized.

▶ The distance to radios must be sufficient (>> 1 m).
▶ Screen command value lines, do not lay them close to power cables, screen solenoid conductors.
▶ Do not use free-wheeling diodes in the solenoid conductors.
▶ With a strongly fluctuating operating voltage, it may in individual cases be necessary to use an external smoothing
capacitor with a capacity of at least 2200 μF.
▶ Recommendation: Capacitor module VT 11110 (see data sheet 30750); sufficient for up to 3 amplifier modules.

Bosch Rexroth AG © This document, as well as the data, specifications and other information set
Hydraulics forth in it, are the exclusive property of Bosch Rexroth AG. It may not be repro-
Zum Eisengießer 1 duced or given to third parties without its consent.
97816 Lohr am Main, Germany The data specified above only serve to describe the product. No statements
Phone +49 (0) 93 52 / 18-0 concerning a certain condition or suitability for a certain application can be
[email protected] derived from our information. The information given does not release the user
www.boschrexroth.de from the obligation of own judgment and verification. It must be remembered
that our products are subject to a natural process of wear and aging.

Bosch Rexroth AG, RE 30223, edition: 2013-01

 Analog amplifier module | VT-MSPA1-1...

Notes

Bosch Rexroth AG © This document, as well as the data, specifications and other information set
Hydraulics forth in it, are the exclusive property of Bosch Rexroth AG. It may not be repro-
Zum Eisengießer 1 duced or given to third parties without its consent.
97816 Lohr am Main, Germany The data specified above only serve to describe the product. No statements
Phone +49 (0) 93 52 / 18-0 concerning a certain condition or suitability for a certain application can be
[email protected] derived from our information. The information given does not release the user
www.boschrexroth.de from the obligation of own judgment and verification. It must be remembered
that our products are subject to a natural process of wear and aging.

RE 30223, edition: 2013-01, Bosch Rexroth AG

 VT-MSPA1-1... | Analog amplifier module

Notes

Bosch Rexroth AG © This document, as well as the data, specifications and other information set
Hydraulics forth in it, are the exclusive property of Bosch Rexroth AG. It may not be repro-
Zum Eisengießer 1 duced or given to third parties without its consent.
97816 Lohr am Main, Germany The data specified above only serve to describe the product. No statements
Phone +49 (0) 93 52 / 18-0 concerning a certain condition or suitability for a certain application can be
[email protected] derived from our information. The information given does not release the user
www.boschrexroth.de from the obligation of own judgment and verification. It must be remembered
that our products are subject to a natural process of wear and aging.

Bosch Rexroth AG, RE 30223, edition: 2013-01