Scribd
Upload
57 views

Toyota Sienna Service Manual Cruise Control Switch Circuit - Diagnostic Trouble Code Chart - Cruise Control System - Cruise Con

Uploaded by

Qwerty Qwert
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
57 views

Toyota Sienna Service Manual Cruise Control Switch Circuit - Diagnostic Trouble Code Chart - Cruise Control System - Cruise Con

Uploaded by

Qwerty Qwert
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

MANUALS NEW TOP SITEMAP CONTACTS SEARCH

Search

Toyota Sienna Service Manual: Cruise Control Switch Circuit


Toyota Sienna Service Manual / Cruise control / Cruise control system /
Diagnostic trouble code chart / Cruise Control Switch Circuit

Watch Full Episodes Online


Full episodes, episode guides, streaming episodes and
more.

Yidio Open

DESCRIPTION

The cruise control main switch operates 7 functions: SET, -


(COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP, and
CANCEL. The SET, TAP-DOWN, and - (COAST) functions, and
the RES (RESUME), TAP-UP, and + (ACCEL) functions are
operated with the same switch. The cruise control main switch is
an automatic return type switch which turns on only while
operating it in the direction of each arrow and turns off after
releasing it. The internal contact point of the cruise control main
switch is turned on with the switch operation. Then the ECM reads
the voltage value that has been changed by the switch operation
to control SET, - (COAST), RES (RESUME), + (ACCEL), and
CANCEL.

WIRING DIAGRAM

INSPECTION PROCEDURE

1 READ VALUE OF INTELLIGENT TESTER

Chat with an expert Online


Now

A Technician Will Answer Your


Questions in Minutes. Chat Now.

JustAnswer

Open

a. Connect the intelligent tester to the DLC3.


b. Turn the ignition switch to the ON position and turn the
intelligent tester main switch on.
c. Check the DATA LIST for proper functioning of the cruise
control main switch.

ECM (Cruise control):

OK: When the cruise control main switch is operated, the display
changes as shown above.

Result

2 INSPECT CRUISE CONTROL MAIN SWITCH

a. Remove the cruise control main switch.


b. Measure the resistance according to the value(s) in the table
below.

Standard resistance

3 CHECK HARNESS AND CONNECTOR (CRUISE CONTROL


MAIN SWITCH - SPIRAL CABLE)

a. Disconnect the b1 connector from the spiral cable.


b. Measure the resistance according to the value(s) in the table
below.

Standard resistance

4 CHECK SPIRAL CABLE

NOTICE: The spiral cable is an important part of the SRS airbag


system. Incorrect removal or installation of the spiral cable may
prevent the airbag from deploying. Be sure to read the page
shown in the brackets.

HINT:

Removal (34)
Installation (34)

a. Remove the spiral cable.


b. Measure the resistance according to the value(s) in the table
below.

Standard resistance

HINT: The spiral cable makes a maximum of approximately 5


rotations.

CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM


AND BODY GROUND)

a. Disconnect the E5 connector from the ECM.

b. Measure the resistance according to the value(s) in the table


below.

Standard resistance

REPLACE ECM

Chat with an expert Online


Now

A Technician Will Answer Your


Questions in Minutes. Chat Now.

JustAnswer

Open

Input Signal Circuit Cruise Main Indicator


Malfunction Light Circuit
DTC P0607 Input Signal Circuit DESCRIPTION The ECM
Malfunction DESCRIPTION This detects a cruise control switch
DTC indicates internal signal and sends it to the
abnormalities of the ECM. DTC combination meter through CAN
No. Detection Item Trouble Area and BEAN. Then the CRUISE
P0607 The E ... main indicator light comes on.
The CRUISE ...

Other materials:

Removal
1. REMOVE BATTERY 2. REMOVE AIR CLEANER ASSEMBLY
HINT: (See page EM-26) 3. REMOVE SPEED SENSOR (NT
SENSOR) (a) Disconnect the speed sensor connector. (b)
Remove the bolt and speed sensor. 4. REMOVE SPEED
SENSOR (NC SENSOR) (a) Disconnect the speed sensor
connector. (b) Remove th ...

Checking and replacing fuses


If any of the electrical components do not operate, a fuse may
have blown. If this happens, check and replace the fuses as
necessary. Turn the engine switch to the “LOCK” position (vehicles
without a smart key system) or off (vehicles with a smart key
system). Open the fuse box cover. ...

Maintenance requirements
To ensure safe and economical driving, day-to-day care and
regular maintenance are essential. It is the owner’s responsibility
to perform regular checks. Toyota recommends the following
maintenance: General maintenance General maintenance should
be performed on a daily basis. This can be done ...

© 2011-2024 Copyright www.tsienna.net

You might also like