Scribd
Upload
161 views

PI MeasPlancks p3

This document provides instructions for an experiment to measure Planck's constant using LEDs of different colors. The equipment needed includes batteries, resistors, potentiometers, and LEDs. A graph of voltage versus frequency for different LEDs will be made and its slope multiplied by the elementary charge will yield a value for Planck's constant. Sources of error include human error in determining when LEDs first glow and the fact that LEDs emit a range of frequencies rather than a single value.

Uploaded by

damian pope
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
161 views

PI MeasPlancks p3

This document provides instructions for an experiment to measure Planck's constant using LEDs of different colors. The equipment needed includes batteries, resistors, potentiometers, and LEDs. A graph of voltage versus frequency for different LEDs will be made and its slope multiplied by the elementary charge will yield a value for Planck's constant. Sources of error include human error in determining when LEDs first glow and the fact that LEDs emit a range of frequencies rather than a single value.

Uploaded by

damian pope
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Curriculum Links

Quantum nature of light, particle model of light.

Equipment needed

6 V battery
1 kO potentiometer
330 O resistor
voltmeter
five connecting leads
set of LEDs that produce five different colours of light in the visible
spectrum,
eg. Knight Lites KSB-1372, KSB-1393, KSB-1356, KSB-1337 and KLL-
5058A.
Viewing tube (optional, see Appendix for details)

Experiment Set Up

Background Information
What is a potentiometer? What is an LED? See Appendix.

Purchasing LEDs and Potentiometers


LEDs are inexpensive and readily available. They often cost less than a dollar and can
be purchased from many electronic stores or ordered online. Most brands of LEDs are
suitable for use in this laboratory activity. Any size of LED is also suitable but one of

file:///H|/perimeter_institute/teaching_resources/measuring%20planck's%20constant/website/PI_MeasPlancks_p3.html[11/11/2008 4:46:27 PM]


the most common sizes is 5 mm in diameter. Potentiometers are also inexpensive and
readily available. The most common type has three terminals (see Figure 7 in the
Appendix) and this is the type used in this lab activity.

Theory Remove this bullet point

• When we apply a large enough potential difference across a light-emitting


diode (LED), it emits photons that all have the same frequency.

• When the LED just begins to glow, the energy E lost by each electron as it
passes through the LED is converted into the energy of a single photon.

• The energy lost by each electron is E = eΔV, where e is the elementary charge
(1.6 x 10-19 C) and ΔV is the potential difference across the LED.

• The energy E of a photon of frequency f is E = hf , where h is Planck’s constant


(h = 6.63 x 10-34 Js).

• Equating the two energies yields eΔV = hf

• Plotting ΔV against f for LEDs of several different colours produces a straight


line of slope h/e.

• Measuring the graph’s slope and multiplying it by e yields Planck's constant.

Useful Constants

c = 3.0 x 108 m/s


e = 1.6 x 10-19 C
h = 6.63 x 10-34 Js

Cautions

1. Students should not stare directly at LEDs when they are brightly lit. LEDs
are safe when they just begin to glow, but they quickly become bright as the
potential difference across them increases above the threshold value. Be
especially careful with the blue LED as the upper part of its frequency
spectrum is very close to the ultra-violet region which can cause permanent eye
damage. Students should not stare at the blue LED even when it is dimly lit.

2. LEDs can be destroyed if the current flowing through them is too large. The
purpose of the 330 O resistor connected in series with the LED is to limit the
current flowing through the LED. This current should be no more than about 50
mA.

3. The potentiometer can be destroyed if wired incorrectly. Students should be


careful when wiring the potentiometer. If they wire it incorrectly, they can create
a short circuit which leads to a large potential difference across a low resistance.
This can result in the potentiometer heating up rapidly, producing a visible
quantity of smoke and ceasing to function. To prevent problems from occurring,
you may wish to inspect your students’ circuits before allowing them to connect
the battery. You may also wish to give your students extra assistance by labelling
the terminals of the potentiometer and the LED (with tape, for example, or by

file:///H|/perimeter_institute/teaching_resources/measuring%20planck's%20constant/website/PI_MeasPlancks_p3.html[11/11/2008 4:46:27 PM]


colour-coding them with paint) to indicate where they should be connected.

Sample Results:

Graph

Remove these bullet points and


Analysis
move the text to the right.
• slope of graph = h/e = (0.19 V)/(4.0 x 1013Hz) = 4.75 x 10-15 Js/C
• h = (4.75 x 10-15 Js/C) (1.6 x 10-19 C) = 7.6 x 10-34 Js
'h' should be italicized
This result is 15% above the true value, which is reasonable for this lab. Errors of 15-
20% are common.

Note that the graph has a false origin. If the line of best fit is extended to the left it does
not pass through the origin, but instead intercepts the ΔV axis at -0.80 V. One reason
for the intercept not being 0 V is the fact that the formula eΔV = hf is only approximate.
In reality, eΔV < hf as electrons in the LED have some thermal energy. When the
potential difference across the LED is less than hf, this thermal energy can provide
enough extra energy for a photon with frequency f to be created. Note, however, that
the thermal energy of electrons is typically significantly less than eΔV and so cannot
account for the entire deviation of the intercept from the origin.

Errors
There are several possible sources of error in this experiment. First, there is the human
error associated with seeing the point at which the LED just begins to glow. The results
obtained can vary depending on whether or not a viewing tube is used to block out
other sources of light, whether or not room lights are on, etc. For optimal results, using

file:///H|/perimeter_institute/teaching_resources/measuring%20planck's%20constant/website/PI_MeasPlancks_p3.html[11/11/2008 4:46:27 PM]


a viewing tube is recommended.

Another source of error is the fact that LEDs do not emit a single frequency of light.
Instead, they emit a narrow spectrum with a width of approximately 60 nm. The
frequency values plotted on the horizontal axis are the central frequency emitted by the
LEDs, but when the LEDs just begin to glow, we typically see slightly lower
frequencies.

Answers
'h' should betoitalicized
Questions in the Student Instruction Sheet

1. The sample result of h = 7.6 x 10-34 Js is 15% greater that the known value.

2. The frequency of green light is given by the following equation:

Energy of a green photon:

The number of photons emitted by the laser each second is:

3. Ultra-violet light has a higher frequency than visible light and so, using the
formula E = hf, ultra-violet photons have more energy than visible ones. Thus,
ultra-violet photons can cause more damage to the cells in our bodies when they
impact on them.

file:///H|/perimeter_institute/teaching_resources/measuring%20planck's%20constant/website/PI_MeasPlancks_p3.html[11/11/2008 4:46:27 PM]

You might also like