Scribd
Upload
20 views

Constant Current Circuit Using Transistors

Uploaded by

Marcelino Silva
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
20 views

Constant Current Circuit Using Transistors

Uploaded by

Marcelino Silva
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 14

Constant current circuit using

transistors
Here is a constant current circuit using transistors. Because the
Ni-HM battery should only be charged with a constant current. Our
friends need it. Also, I and my daughter are interested in
learning/trying out this circuit.

Normally the current will change always according to the voltage


level. Imagine an LED display, when higher voltage, it gets a higher
current, too. Of course, it can get damaged.

Learn first: transistor circuit

For the battery, when it runs out of power. Its internal voltage and
resistance are very low. While charging, the current is very high. It
causes by very high heat, which is not a good result at all.

Would it be better if charged with the constant current? The current


flowing through it is low and constant. It doesn’t get hot, so it can be
recharged many times.

Basic Constant current circuit Learning


There are many types of constant current generator circuits. This
time we choose to study a transistor circuit. It’s cheap and easy. Sure,
we should start in a simple way. Look at below.

We believe that problems make the best learning. From; How to use
easily LEDs. But the LED emits light unsteadily when used with a
higher voltage source.
The LED needs constant current. For the voltage, it will be pulled up
by itself, as required. When we keep the current constant. It will pull
the voltage is almost constant. Of course, the light is more stable, too.
Is this nature of LED true?

Let’s found out.

Experiment basic circuit

We try to set the condition to use the 3mm red LED again and a
voltage source of 5V to 12V. From the basic circuit above, let’s choose
the parts list.

1. Q1: When we use the 3 mm LED, the voltage level is just


like that. We can use any small NPN transistor, e.g. BC547,
BC337, 2SC1815, 9013, 2N2222, etc. We use 2N3904. Note: Be
careful with the different leg positions.
2. R2: Bias current (IB) resistor to a transistor. We use 4.7K
because of the low lC.
3. D1, D2: We use 1N4148, this circuit requires low current.
4. R1: It’s the most important Because it defines constant
current to the load (LED).

We can easily calculate its value:

R = 0.7V ÷ I

We know I, is constant current, is ILED. The current lowest of LED is


about 3mA(0.003A).
So, R1 = 0.7V ÷ 0.003A = 233Ω. But we use a 220Ω resistor.

Or see Shopping List:

0.25W Resistors, tolerance: 5%

● R2: 4.7K, Quantity: 1


● R1: 220Ω, Quantity: 1

Semiconductors

● Q1: 2N3904, 45V 0.1A, NPN TO-92 Transistor; Quantity: 1


● LED1: 3mm red LED; Quantity: 1
● D1: 1N4148, 75V 150mA Diodes; Quantity: 2

Then, look at the circuit diagram below. Even, fewer pieces of


equipment. But it might seem confusing for beginners.
Assemble this circuit on a breadboard, and compare the results when
we change input voltage, between 5V to 12V. Notice the LED, it’s
steadily bright. Great!

If you still don’t understand clearly, try reading this: Electronics


for beginners

Measure the current of the LED. It is constant at 2mA in all voltage


ranges. And measuring the LED voltage is 1.9V constant as well. See
the illustration below.
Note: The meter gets less precise than the calculated formula a bit.

Why current is constant?

Now coming to the difficult, I have a big question: how to explain the
operation of the circuit in a simple way? until my daughter
understands. This content may not be suitable for people who like
complex principles.

Here are some facts that you should understand for yourself.

When the voltage and resistance are constant, the current is surely
constant. This can be confusing. Look at the circuit again.
See flowing current

The current
flows through the points of the basic circuit.

● No 1: a little current flows through R2, D1, and D2 to GND.


● No2: while some currents flow through R2 to B pin and E
pin of the transistor, and R1 to GND, too. It is a bias current
to the transistor. We call it that IB. So, Q1 conducts. And,
● No 3: Making a large current flows through LED to C pin
and E of the transistor, the R1 to GND, as well. Thus, LED
glows.

We will see that: IC of transistor = ILED, while IE is IR1. From principle:


IE = IC x IB, but because the IB is very small. We may ignore it as IE =
IC (almost the same). In conclusion, ILED = IR1.
We’re going to link it to find out.

The voltage at different points

What’s more. Meare a voltage at various points.

1. VD—D1, D2

There is a constant voltage drop across both diodes of approximately


1.4V. Each diode has a voltage drop of about 0.7V. While is Vin 5V to
12V range. Why?

The principle is: that when a little forward current flows through the
diodes. It will conduct when the forward voltage reaches a certain
threshold point. For Silicon diode is 0.6-0.7V.
It will maintain the voltage level while it is still conducting.

2. VBE and VR1

Look at the above illustration circuit. Both diodes D1-D2 are across
B-E of transistor and R1. Sure, they are also forced to keep the voltage
constant,1.4V. Then,

● The internal structure of the transistor between the B-E pin


is like a diode. So, the voltage across B-E is 0.7V.
● Thus, the voltage at R1 is 0.7V (constant as well) So we can
easily link to calculate the formula above.

R1 = 0.7V ÷ ILED

In conclusion, when VR1 is fixed at 0.7V. So, the ILED (load) is stable
too, meeting our goal.

Make Ni-MH battery charger circuit

We have learned enough about the constant current circuit using


transistors. Let’s make a Ni-MH battery charger circuit. Currently, the
Ni-MH battery has more capacity more than 1500mA or 1900mA, high
efficiency.
Next, let’s see how to choose the right devices.

● We should charging current—ICharging about 0.1C or capacity


battery x 0.1 = 1900mA x 0.1 = 190mA. We set it about
170mA.
● Sure, a small transistor cannot get it. We need to use a
larger one.
● There be should LED display battery are charging.
● Easy same above circuit.

Look at the circuit diagram below.


● Change D1, and D2 into a LED. Also, It can keep a stable
voltage. Besides, It indicates battery connecting.
● Put another power transistor—Q2-2N3055, to deliver
170mA of output current. Also, we put Q1 and Q2 in
Darlington pair form, causing have high gain to drive the
load.
Note: You may use TIP41, MJE3055, and more. They are
smaller than one, on TO-220. But I love 2N3055, it is more
durable and has high performance.
● Calculate the value of R1 = 0.8V/ICharging = 0.8V/0.17A =
4.7Ω. And, Power = V x I = 0.8V x 0.17A = 0.13W, or use
0.25W resistor.
● Use LED1 as a 5mm Green LED. It will keep a voltage at
about 2.1V and be stable, too.

Then, assemble this circuit on a breadboard. Measure the voltage at


various points. Look at the circuit diagram below.
There are 3 points we need to measure voltages.

1. Measure voltage across LED1 should read about 2.1V. It will


keep the circuit running and stable.
2. Point 2 is about 1.4V, results from Q1 and Q2 conducts.
3. The voltage of R1 needs to be about 0.8V, Output current
will be constant to the battery (load).

We tried charging one AA Ni-MH battery. See the Figure below.

Then, measure the current is about 0.170A. Meanwhile while


charging, we measure the voltage drop across The battery as 1.4V. No
more than the specified value is 1.5V. Then, we tried charging it for 16
hours. The battery is normal, not more than 40 degrees Celsius.
Note: As the circuit operates, Q2 rises in temperature. Therefore
should be installed on the heatsink. and if charging only one battery
we may try to reduce Vin to 5V. The Q2 has a lower temperature. Sure,
Vin should be regulated power supply.

Thanks, Harald Brötell our friend who sparked trying this circuit. We
had a lot of fun.

I and my kids love to learn electronics. I also found a Simple Constant


Current Generator using Transistor with helping of TL431, Even
though it uses IC. But it is good learning more.

In conclusion, We hope this circuit will be helpful to you. If you have


tried What results did you get? Please don’t delay, share with us

You might also like