Learn By Topic Design Insights Videos Latest Blogs  Us

Contact
3D ECAD/MCAD and Rigid Flex E-Books Allegro X
Design Data Management Migration Guides OrCAD X
DesignHome 〉 Blog
Reliability 〉 How Bootstrap Capacitors Work infrom
PCB Design Switching
Start toRegulators
Finish PSpice
Design Reuse and Productivity Technical Papers Webinars
HDI and Miniaturization
High Speed Design and Analysis
IC Packaging
How Bootstrap Capacitors Work in
Layout and Routing

Switching Regulators
Manufacturability
PCB Design
RF/Microwave Design

CADENCE PCB SOLUTIONS
Schematic Capture and Circuit
Simulation
Signal/Power Integrity

TOP
Switching regulators are susceptible to a particular form of ine�ciency known as switching
losses. One of the challenges in switching regulator design is to balance the various sources
of radiated and conducted noise against system complexity and switching/conduction ×
losses. Simple tricks like running at higher frequency, interleaving/multi-phasing, and using
better MOSFETs will help increase power conversion e�ciency. Another simple option is use
of a capacitor in the switching stage, also known as a bootstrap capacitor.

This capacitor is often connected across two terminals on integrated switching regulators TOP
that include a gate drive stage integrated onto the semiconductor die. If you are building a
DC/DC converter from discrete components, a bootstrap capacitor can also be used to
provide reduced switching losses.

Bootstrap Capacitors in a Switching Regulator

Bootstrap capacitors are used in synchronous or asynchronous switching regulators to aid
switching action in a MOSFET. Most often, they are used in synchronous switching
regulators. The placement of the bootstrap capacitor in these circuits is such that it
discharges into the gate driver’s power port for the high side MOSFET. An example with a
synchronous buck converter is shown in the circuit diagram below.

TOP
The placement across the switching node and driver input ensures that the gate driver
voltage remains above the input voltage during switching. This ensures that the high-side
MOSFET remains fully ON during switching, which decreases switching losses. This works
because the reference voltage for the bootstrap capacitor is the switching node, not the
ground node.

Bootstrapping Process
Bootstrap capacitors operate in three stages:
Charging phase: When the low-side MOSFET is ON (high-side is OFF), the bootstrap
capacitor charges. One side of the bootstrap capacitor is connected to a fixed voltage source
(usually the input voltage or a derived voltage), and the other side is connected to the
switching node, which is essentially ground when the low-side MOSFET is on. So, the
bootstrap capacitor charges up to the fixed voltage.

Bootstrap phase: When the low-side MOSFET turns OFF and the high-side MOSFET turns
ON, the switching node voltage rises. As long as the capacitor maintains a nearly constant
voltage, the voltage seen at the other terminal of the bootstrap capacitor (connected to the
high-side gate driver) also rises. The driver rails out at this elevated voltage as it drives the
high-side MOSFET gate.

Discharging phase: The bootstrap capacitor discharges slowly to supply the necessary gate
charge to the high-side MOSFET. The high-side MOSFET remains ON as long as the bootstrap
capacitor can maintain a voltage high enough to keep it in saturation. ×
This process repeats with each switching cycle as the high-side and low-side MOSFETs
switch ON and OFF.

How to Size a Bootstrap Capacitor

Sizing of a bootstrap capacitor is rather simple and it depends on the level of charge TOP
compensation required to maintain the high-side MOSFET in its ON state. First, we look at the
amount of charge required to maintain the high-side MOSFET gate in the ON state.

This exact amount of charge required (QG) depends on the construction of the MOSFET and
it is generally determined through measurement in PMICs or DC/DC converter ICs. Typically it
will be on the order of 1-10 nF for integrated DC/DC converters, but it could be much greater
for physically larger discrete power MOSFETs. The ID term is the discharge current from the
capacitor during switching between HIGH and LOW sides, D is the duty cycle, and f is the
switching frequency.

The minimum required value for the bootstrap capacitor is:

VBS is the minimum value the gate voltage is required to be above the input voltage during
switching to maintain the MOSFET in saturation. Typically, datasheets for DC/DC converter
ICs will provide a lower limit on the capacitor as a function of VBS. You may also find some ×
measurement data in the datasheet that provides a better idea of expected performance.

The above calculation assumes that the bootstrap capacitor has minimal inductance and
resistance along the discharge path and in the body of the capacitor. Therefore, bootstrap
capacitors are usually placed as small-case SMD ceramic capacitor (e.g., 0402 with C0G or
TOP
X7R dielectric). For integrated buck converters that have BOOT pins, the inductance and
resistance will almost always be minimal along the discharge path as long as the bootstrap
capacitor is placed close to the BOOT pin.

No matter how you want to control power sequencing and on-o� timing for your devices,
you can create and evaluate your circuits with the complete set of simulation tools in PSpice
from Cadence. PSpice users can access a powerful SPICE simulator as well as specialty
design capabilities like model creation, graphing and analysis tools, and much more.
Subscribe to our newsletter for the latest updates. If you’re looking to learn more about how
Cadence has the solution for you, talk to our team of experts.

About the Author

Cadence PCB solutions is a complete front to back design tool to enable fast and e�cient product creation.
Cadence enables users accurately shorten design cycles to hand o� to manufacturing through modern,
IPC-2581 industry standard.

Follow on Linkedin Visit Website More Content by Cadence PCB Solutions

Learn More
TOP
 PREVIOUS ARTICLE NEXT ARTICLE

〈 〉

MOST RECENT ARTICLES 〈 〉

Cadence TECHTALK: PCB Layout Tools in Next-Generation How to Generate a BOM

Introducing OrCAD X: OrCAD X Electronic Circuit Design in OrCAD X
Webinar Recap Software ×
Discover how OrCAD X The Bill of Materials
This article recaps the advanced PCB layout OrCAD X o�ers familiar (BOM) describes the
“Cadence TECHTALK: tools enable design electronic circuit design components and
Introducing
Read Article OrCAD X” › productivity,
Read Article with › software performance ›
Read Article materials
Read Articlethat go into
webinar, which features like with a new UI and PCB manufacturing. This
TOP
 Return to Home

A Great Place to Do Products Company Media Center Contact Us

Great Work! Custom IC and RF About Us Newsroom General Inquiry
Seventh year on the FORTUNE
100 list Digital Design and Events Designed with Customer Support

Our Culture Join The Team Signo� Cadence

Leadership Team Media Relations
IC Package Blogs
Investor Relations Global O�ce
IP Forums Locator
Alliances
PCB Design
Careers
System Analysis
Cadence
Veri�cation Academic
Network
All Products

© 2024 Cadence Design Systems, Inc. All Rights Reserved. Terms of Use | Privacy Policy | US Trademarks | Do Not Sell My Personal Information Connect with us    

TOP