PT BUKITAPIT BUMI PERSADA

Cementing - Stimulasi - Fracturing

Coiled Tubing - Nitrogen Services

STIMULATION PROPOSAL
MATRIX ACID 15% HCL
Thursday, November 21, 2024

PT. PERTAMINA HULU ROKAN

ZONE 4 SUMATERA BAG. SELATAN
LIMAU FIELD

WELL : KRG-009
Lap. A3 (1272.5-1275.5 m)(1277-1279 m)(1287-1289 m)

REVISED: 0
21 November 2024 rev 0 : Initial Design

Prepared for Prepared by

Syahrul S Dian Supriana P.
Reza Ramadhan Ahmad Fauzan
Umi Kalsum
PT Pertamina Hulu Rokan PT BBP Prabumulih

CORPORATE OFFICE OPERATIONAL OFFICE WORKSHOP PRABUMULIH BASE

Jl. Palem Raya No. 9 Kel. Jatimekar Kec. Jatiasih Jl. Raya Nigata Lapangan Golf Pertamina Prabumulih
Jl. Taman Margasatwa No. 45 Ragunan Bekasi 17422 Sumsel 31123
Jakarta 12550 Tlp: 021-84976121,84976105 Fax: 021-84976145 Tlp: 0713-322795 Fax: 0713 - 322109
Tlp: 021- 78838142 / 78838057 Fax: 021-78837905

21/11/2024 Page 1 of 8
 PROPOSAL MATRIX ACIDIZING HCl 15%
PT. BUKITAPIT BUMI PERSADA WELL: KRG-009

FORMALITIES
REVISED: 0

Inj DOCUMENT TITLE

Proposal Matrix Acid 15% HCl KRG-009

AUTHORIZATION

NAME POSITION COMPANY SIGNATURE DATE

DIAN SUPRIANA P. / TECHNICAL PT BUKITAPIT

PREPARED BY 21-Nov-24
AHMAD FAUZAN ENGINEER BUMI PERSADA

REVIEED & PT BUKITAPIT

IRWAN SYAFRUDIN BASE MANAGER 21-Nov-24
APPROVED BY BUMI PERSADA

PERTAMINA
CUSTOMER WELL INTERVENTION HULU ROKAN
SYAHRUL S
APPROVAL ENGINEER ZONA 4
PERTAMINA
CUSTOMER PETROLEUM HULU ROKAN
REZA RAMADHAN ZONA 4
APPROVAL ENGINEER AREA 2

LABORATORY REPORT SOLUBILITY TEST:

21/11/2024 Page 2 of 8
 PROPOSAL MATRIX ACIDIZING HCl 15%
PT. BUKITAPIT BUMI PERSADA WELL: KRG-009

CONTENT
PAGE

1 SUMMARY 3

2 WELL DIAGRAM 4

4 CALCULATION 5

5 JOB PROCEDURE 6

6 EQUIPMENT USED 6

7 CONTIGENCY PLAN 6

8 MATERIAL REQUIRED 7

9 COST ESTIMATION 7

10 PRODUCT INFO 7

ATTACHMENT - JOB SAFETY ANALYIS

21/11/2024 Page 2 of 7
 PROPOSAL MATRIX ACIDIZING HCl 15%
PT. BUKITAPIT BUMI PERSADA WELL: KRG-009

1 SUMMARY
REVISED: 0

Injectiviry test result (11 November 2016): 0.06 BPM 1300 PSI

KRG-009 is Production well at Interval perforation Lap. A3 (1272.5-1275.5 m)(1277-1279 m)(1287-1289 m). This well is
proposed to be stimulated with Acidizing (HCl 15%) to restore formation conductivity by dissolving carbonate-based
material near wellbore. This proposal Matrix Acidizing treatment design using 93 GPF, so that damage can be
removed in 5 ft radial penetration from the wellbore.

The job procedure will be designed into 4 stages;

No Stage
1 Injectivity Rate Test (IRT)
2 Pump Pre Flush
3 Pump Main Treatment
4 Displace

LABORATORY REPORT SOLUBILITY TEST:

21/11/2024 Page 4 of 8
 PROPOSAL MATRIX ACIDIZING HCl 15%
PT. BUKITAPIT BUMI PERSADA WELL: KRG-009

2 WELL DIAGRAM
REVISED: 0

Target Acid :
Lap. A3 (1272.5-1275.5 m)
(1277-1279 m)
(1287-1289 m)

21/11/2024 Page 4 of 7
 PROPOSAL MATRIX ACIDIZING HCl 15%
PT. BUKITAPIT BUMI PERSADA
WELL: KRG-009

4 CALCULATION
REVISED: 0

Objective: to restore formation conductivity by dissolving carbonate-based material near wellbore to achieve target injection

4.1 CASING/TUBING DATA :

OD Weight ID Depth, (m)
Description
inch lb/ft inch Top Bottom
Casing Liner 7 23.0 6.366 0.0 1629.0
Packer 7 Tailpipe tbg +/- 1 7 6.366 1260.0
Tbg EOS joint 2 7/8 6.4 2.441 0.0 1270.0
Perfo 1272.50 1275.50
BP/TOC

4.2 PRESSURE CALCULATION:

BHST 220 deg.F BHSP 1663 psi
HCl 15% Friction Press@ 2 BPM 111.5 psi Brine Water Friction Press@ 2 BPM 92 psi
Estimated Frac. Gradient 0.7 psi/ft Estimated BH Frac Pressure 3110 psi

Injectivity HCl 15% Displace

SG 1.011 1.074 1.011
Density (ppg) 8.43 8.96 8.43
Press Hydrostatic (psi) 1827 1941 1827
±Surface Treating Pres.(psi) 1376 1281 1376

4.3 VOLUME CALCULATION :

2 7/8 "Tubing Capacity 0.00579 bbl/ft x 1270.0 m vol. = 24.1 bbl
7 "Casing Capacity 0.03935 bbl/ft x 5.5 m vol. = 0.7 bbl

Zone Interval (m) (m) (ft) Total (ft) Mineralogy Permeability

1272.5 - 1275.5 3.0 9.8 mD
A3 1277.0 - 1279.0 2.0 6.6 23.0 mD
1287.0 - 1289.0 2.0 6.6 mD

Ri (radial-penetration) 5 ft
Average Porosity 14 % 2109.3 gall 50.0 bbl
Mixing Acid Treatment 93 gpf 50.0 bbl

4.4 TREATMENT PROCEDURE :

A Tubing Pickle HCl 7.5% - gall - bbl
Step No. Product Code Concentration Volume
1 Fresh water - 761 gpt - gall
2 Corrosion Inhibitor BCI-05 30 gpt - gall
3 Iron Control BIC-30 50 pptg - lbs
4 Hydrochloric Acid HCl 32% 209 gpt - gall
● Displace-Formation Water 1,008 gall 24 bbl
● Reverse Out-Formation Water by Rig Pump 2,024 gall 48 bbl

B Injectivity Test, etc.(Include Fill up Well) 840 gall 20 bbl

1 Formation Water 1,000 gpt 840 gall
2 2% KCl 167 pptg - lbs
Ri = ± 3 ft
C Pre Flush
15 gpf 336 gall 8 bbl
Step No. Product Code Concentration Volume
1 Fresh Water - 946 gpt 318 gall
2 2% KCl BAA-12 167 pptg 56 lbs
3 Mutual Solvent BMS-50 50 gpt 17 gall
4 Nonionic Surfactant BSU-12N 4 gpt 1 gall
Ri = 5 ft
D Main Acid Treatment
HCl 15% 2,100 gall 50 bbl
Step No. Product Code Concentration Volume
1 Fresh water - 488 gpt 1,025 gall
2 Corrosion Inhibitor BCI-05 26 gpt 55 gall
3 Corrosion Inhibitor Aid BCI-01 gpt - gall
4 Iron Control BIC-30 30 pptg 63 lbs
5 Mutual Solvent BMS-50 50 gpt 105 gall
6 Nonionic Surfactant BSU-12N 2 gpt 4 gall
7 Hydrochloric Acid HCl 32% 434 gpt 911 gall

E Displacement 1,042 gall 25 bbl

1 Formation Water 1,000 gpt 1,042 gall

21/11/2024 Page 6 of 7
 PROPOSAL MATRIX ACIDIZING HCl 15%
PT. BUKITAPIT BUMI PERSADA
WELL: KRG-009

5 JOB PROCEDURE
REVISED: 0

PRE JOB:
1 Use appropriate HSE: APD, Bring face wash, respiratory mask, apron for crew mixing acid, etc.
2 RIH 2.875" tubing with packer set at 1260 m and EOS at 1270 m (minimum 6 jts DC 4 3/4).
3 Transfer to BBP tank Fresh Water 32 bbl: 8 bbl for Pre Flush
0 bbl for Pickle
24 bbl to Acid Tank - for Acid Treatment
4 Transfer to BBP tank Formation Water min. 69 bbl to water tank.

EQUIPMENT PREPARATION:
1 Rig up BBP pumping unit.
2 PJSM and review the job procedure. Ensure all crew wear PPE. Prepare Injectivity Rate Test
3 Test BBP line to 2500 psi for 5 minutes, ensure there's no leaking, bleed off press 0 psi.

TUBING PICKLE:
1 Mix & pump 0 bbl tubing pickle and displace with 24 bbl formation water.
2 Reverse out circulation pickle by Rig pump 2x vol string (48 bbl) via annulus or until clean pH neutral.

INJECTIVITY TEST:
1 Set packer test from annulus 300-500 psi, conduct injectivity test as schedule below with formation water. (Max. STP : 1659 psi)
Est.Target WI Rate Time Volume Pump Press
(BWIPD) (BPM) (MINUTE) (BBL) (PSI)
Fill up well (est.) -
720 0.5 2 .........
1440 1 4 .........
2160 1.5 4 .........
2880 2 4 .........
3600 2.5 6 .........
Total 20

- Mixing acid treatment after injectivity test confirmed & discussed with company representative.
- Frac pressure shall obtain to know the maximum rate-pressure can be applied on this well.
- If no rate or tight formation after injectivity test; unset packer, mix & drop 8 bbl acid treatment & displace as vol tbg, soak for 30 mins. Continue to perform injectivity
test, any increasing on rate, mixing the remaining acid.

PUMPING SCHEDULE (BASED ON IRT)

1 Pump : 8 bbl Pre Flush

2 Pump : 50 bbl Acid HCl 15% Treatment
3 Pump : 25 bbl Displace Formation Water
- Add amount of Corrosion Inhibitor to acid tank that already filled with water and agitate/mix with air or circulation. Add other additives at this time.
- Acid solution need thoroughly mixed to assure uniform treatments, otherwise the acid strength can vary in the mixture.
- Pumping Pressure is not allow exceeding the test line.

4 Stop pump, bleed off pressure & R/D BBP equipment and job completed.

POST JOB:
1 Clean up all unit from acid (Pumping Unit, Lines, Tanks, etc) by flushing with fresh water + soda ash
2 Housekeeping before leaving location.

6 EQUIPMENT USED

1 ea Triplex Pumping Unit 1 ea Water tank min.50 bbl 1 ea Air Compressor

1 ea CDAS 1 ea Acid Tank min. 50 bbl 1 set Chemicals
1 ea Welden Pump 1 ea Retrievable packer 7"

7 CONTIGENCY PLAN

IF Leaking on lines / pump 1. Maximun treating pressure not exceed test line pressure
unit : 2. Always fill up displacement tank with water
3. Stop pump acid, switch to pump clean water at displacement tank, stop pump, close master valve at rig floor, bleed off
pressure into secure area/pit tank until no more fluid flowing through the line, open/fix the leaking part
4. Pour the leaking area with water & Soda Ash
5. If acid still in the tubing/wellbore when the pumping stopped, reverse out using rig pump
6. If acid already pumped into formation, using rig pump, pump brine water at minimum volume 1/2 from acid that already
pumped into formation

21/11/2024 Page 6 of 7
 PROPOSAL MATRIX ACIDIZING HCl 15%
PT. BUKITAPIT BUMI PERSADA WELL: KRG-009

8 TOTAL MATERIAL REQUIRED

REVISED: 0

No. Product BBP A B C D E

CODE TOTAL MATERIAL LOAD OUT
Pickle 1st Inject Pre Flush Acid Displ
1 Fresh Water - - - 318 1,025 - - 1,343 gall 32.0 bbl
2 Formation Water - 1,008 840 - - 1,042 2,890 gall 68.8 bbl
3 Iron Control Additive BIC-30 - - - 63 - - 63 lbs 1.1 sax (55lbs/sx)
4 Corrosion Inhibitor BCI-05 - - - 55 - - 55 gall 1.0 drum (55gl/drm)
5 Nonionic Surfactant BSU-12N - - 1 4 - - 5 gall 0.1 drum (55gl/drm)
6 Mutual Solvent BMS-50 - - 17 105 - - 122 gall 2.2 drum (55gl/drm)
7 Hydrochloric Acid HCl 32% - - - 911 - - 911 gall 16.6 drum (55gl/drm)
8 Acid Neutralizer Soda Ash - - - - - - 550 lbs 5.0 sax (110lbs/sx)
9 KCl BAA-12 - - 56 - - 56 lbs 0.5 sax (110lbs/sx)
10 Corrosion Inhibitor Aid BCI-01 - - - - - - - gall 0.0 drum (55gl/drm)

9 COST ESTIMATION

A SERVICE COST:
No. REFF NO. DESCRIPTION QTY UNIT UNIT PRICE TOTAL PRICE
1 Matrix Acidizing 1 Job Rp 165,000,000 Rp 165,000,000

Sub Total A: Rp 165,000,000

B MATERIAL COST:
TOTAL PRICE
No. PROVIDE BY DESCRIPTION CODE QTY UNIT UNIT PRICE TOTAL PRICE
(HCL F. LIMAU)
1 PERTAMINA Fresh Water - 39.0 bbls Rp - Rp - Rp -
2 PERTAMINA Formation Water - 69.0 bbls Rp - Rp - Rp -
3 PT.BBP Iron Control Additive BIC-30 63.0 lbs Rp 35,000 Rp 2,205,000 Rp 2,205,000
4 PT.BBP Corrosion Inhibitor BCI-05 55.0 gall Rp 200,000 Rp 11,000,000 Rp 11,000,000
5 PT.BBP Nonionic Surfactant BSU-12N 5.0 gall Rp 187,500 Rp 937,500 Rp 937,500
6 PT.BBP Mutual Solvent BMS-50 122.0 gall Rp 160,000 Rp 19,520,000 Rp 19,520,000
7 PT.BBP Hydrochloric Acid HCl 32% 911.0 gall Rp 25,000 Rp - Rp 22,775,000
8 PT.BBP Acid Neutralizer Soda Ash 550.0 lbs Rp 6,000 Rp 3,300,000 Rp 3,300,000
9 PT.BBP Corrosion Inhibitor Aid BCI-01 - lbs Rp 130,000 Rp - Rp -
9 PT.BBP KCl BAA-12 56.0 lbs Rp 7,500 Rp 420,000 Rp 420,000
Sub Total B: Rp 37,382,500 Rp 60,157,500
C GRAND TOTAL: (A + B) Rp 202,382,500 Rp 225,157,500

Note:
1 Price above excluding PPN 10%.

2 Price above will be adjsuted due the chemical requirements and subject to change depends on field condition.

10 PRODUCT INFO :

• Corrosion Inhibitor BCI-05 A hydrochloric acid corrosion inhibitor. It is effective in all concentrations of hydrochloric acid and can be used
also in formulations which combine hydrochloric acid with others, such as acetic, formic or hydrofluoric acid.
• Corrosion Inhibitor Aid BCI-01 Help increasing temperature limit of BCI-05 and protection time for steel/production string.
• Iron Control BIC-30 : Function to prevent iron precipitation, with functions as chelating agents which form stable water-soluble
complexes with iron. By complexion the iron, its activities are reduced and it is prevented from reacting as
normally expected.

• Mutual Solvent BMS-50 : EGMBE (ethylene glycol monobutyl ether), that is soluble in both hydrocarbon and aqueous solutions. Used in
acid stimulation as a surface tension reducer and water wetting agent. It also helps prevent excessive
• Nonionic Surfactant BSU-12N : adsorption ofor
Used in acid surfactants andstimulation
water-based corrosion inhibitors by keeping
fluids to prevent them in solution.
the formation of emulsions and it has capability to
water-wet limestone formations as well.
• Pottasium Salt (KCl) BAA-12 The base salt for completion fluid also to prevent swelling clay for sensitive formation.

• Hydrochloric Acid HCl 32% Inorganic acid, to dissolve carbonate based material.

• Acid Neutralizer Soda Ash As acid neutralizer by raising pH.

21/11/2024 Page 7 of 7