TWO LAMPS CONNECTED IN SERIES AND

CONTROLLED BY ONE-WAY SWITCH

Lamp-1 Lamp-2

Neutral

230 Volts
AC supply

Phase
One-way
Switch

Circuit diagram

78
 WIRING
Ex. No.4(A). TWO LAMPS CONNECTED IN SERIES AND
CONTROLLED BY ONE-WAY SWITCH
Aim :
To make wiring for two lamps connected in series and controlled by one-way
switch, and verify the circuit connection.

Requirements :

Materials Tools
1) Wooden board for wiring 1) Hand drilling machine
2) Wooden round blocks 2) Hack saw
3) Wood screws 3) Hammer
4) PVC pipes and elbows 4) Cutting plier
5) PVC clamps 5) Screw driver
6) PVC wires for connection 6) Electrician’s knife
7) Batten holders 7) Poker
8) One-way switch 8) Mallet
9) Electric lamps 9) Electrical line tester
10) Insulation tape 10) Multimeter

Procedure :
9) Draw the wiring circuit diagram on the wooden board using white chalk piece.
10) Fix the PVC pipes and elbows as per the circuit diagram using PVC clamps and
screws.
11) Insert required length of PVC wires through the pipe for connection.
12) Fix the wooden round blocks at the correct place using wood screws.
13) Connect the switch and batten holders through wires as per the circuit diagram.
14) Verify the circuit and apply corrections if required.
15) Fix the lamps in the holder. Turn on the power supply and switch.
16) If the lamps glow, the connection is correct. Otherwise detect and rectify the
fault in the connection and verify the circuit again.
Result :
The wiring for two lamps connected in series and controlled by one-way switch
is made. The correctness of connection is verified.

79
TWO LAMPS CONNECTED IN PARALLEL AND
CONTROLLED BY ONE-WAY SWITCH

Lamp-1 Lamp-2

Neutral

230 Volts
AC supply

Phase
One-way
Switch

Circuit diagram

80
Ex. No.4(B). TWO LAMPS CONNECTED IN PARALLEL
AND CONTROLLED BY ONE-WAY SWITCH
Aim :
To make wiring for two lamps connected in parallel and controlled by a one-
way switch, and verify the circuit connection.

Requirements :

Materials Tools
1) Wooden board for wiring 1) Hand drilling machine
2) Wooden round blocks 2) Hack saw
3) Wood screws 3) Hammer
4) PVC pipes and elbows 4) Cutting plier
5) PVC clamps 5) Screw driver
6) PVC wires for connection 6) Electrician’s knife
7) Batten holders 7) Poker
8) One-way switch 8) Mallet
9) Electric lamps 9) Electrical line tester
10) Insulation tape 10) Multimeter

Procedure :
1) Draw the wiring circuit diagram on the wooden board using white chalk piece.
2) Fix the PVC pipes and elbows as per the circuit diagram using PVC clamps and
screws.
3) Insert required length of PVC wires through the pipe for connection.
4) Fix the wooden round blocks at the correct place using wood screws.
5) Connect the switch and batten holders through wires as per the circuit diagram.
6) Verify the circuit and apply corrections if required.
7) Fix the lamps in the holder. Turn on the power supply and switch.
8) If the lamps glow, the connection is correct. Otherwise detect and rectify the fault
in the connection and verify the circuit again.

Result :
The wiring for two lamps connected in parallel and controlled by one-way switch
is made. The correctness of connection is verified.

81
 CEILING FAN CONTROLLED BY
ONE-WAY SWITCH AND REGULATOR

Ceiling
Fan Motor

Neutral

230 Volts
AC supply

Phase
One-way
Switch Fan
Regulator
Circuit diagram

82
Ex. No.5. CEILING FAN CONTROLLED BY ONE-
WAY SWITCH AND REGULATOR
Aim :
To make wiring for ceiling fan controlled by one-way switch through regulator,
and verify the circuit connection.

Requirements :

Materials Tools
1) Wooden board for wiring 1) Hand drilling machine
2) Wooden round blocks 2) Hack saw
3) Wood screws 3) Hammer
4) PVC pipes and elbows 4) Cutting plier
5) PVC clamps 5) Screw driver
6) PVC wires for connection 6) Electrician’s knife
7) One-way switch 7) Poker
8) Fan regulator 8) Mallet
9) Ceiling fan and accessories 9) Electrical line tester
10) Insulation tape 10) Multimeter

Procedure :
1) Draw the wiring circuit diagram on the wooden board using white chalk piece.
2) Fix the PVC pipes and elbows as per the circuit diagram using PVC clamps
and screws.
3) Insert required length of PVC wires through the pipe for connection.
4) Fix the wooden round blocks at the correct place using wood screws.
5) Connect the switch, fan regulator and fan motor through wires as per the
circuit diagram.
6) Verify the circuit and apply corrections if required.
7) Turn on the power supply and switch.
8) If the ceiling fan rotates, the connection is correct. Otherwise detect and
rectify the fault in the connection and verify the circuit again.
Result :
The wiring for ceiling fan controlled by one-way switch and regulator is made.
The correctness of connection is verified.

83
 STAIRCASE WIRING

Lamp

Neutral

230 Volts
AC supply

Phase

Two-way Two-way
Switch-1 Switch-2

Circuit diagram

84
Ex. No.6. STAIRCASE WIRING
Aim :
To make staircase wiring for one lamp controlled by two-way switches at
different locations and verify the circuit connection.

Requirements :

Materials Tools
1) Wooden board for wiring 1) Hand drilling machine
2) Wooden round blocks 2) Hack saw
3) Wood screws 3) Hammer
4) PVC pipes and elbows 4) Cutting plier
5) PVC clamps 5) Screw driver
6) PVC wires for connection 6) Electrician’s knife
7) Batten holders 7) Poker
8) Two-way switches 8) Mallet
9) Electric lamp 9) Electrical line tester
10) Insulation tape 10) Multimeter

Procedure :

1) Draw the wiring circuit diagram on the wooden board using white chalk piece.
2) Fix the PVC pipes and elbows as per the circuit diagram using PVC clamps and
screws.
3) Insert required length of PVC wires through the pipe for connection.
4) Fix the wooden round blocks at the correct place using wood screws.
5) Connect the two way switches and batten holders through wires as per the circuit
diagram.
6) Verify the circuit and apply corrections if required.
7) Fix the lamp in the holder. Turn on the power supply and switch.
8) If the lamp glows, the connection is correct. Otherwise detect and rectify the fault in
the connection and verify the circuit again.

Result :
The staircase wiring for one lamp controlled by two-way switches at different
locations is made and the correctness of connection is verified.

85