AT 2X CHASSIS

LINE UP AT2X Chassis

KLV-V26A10E
KDL-V26A11E
KDL-V26A12U

KLV-V32A10E
KDL-V32A11E
KDL-V32A12U LCD TV

KLV-V40A10E
KDL-V40A11E
KDL-V40A12U

KLV-W40A10E
KDL-W40A11E
KDL-W40A12U

KE-V42A10E
KDE-V42A12U
PDP TV
Best Resolution Audio Visual Integrated Architecture
KE-W50A10E
KDE-W50A11E
KDE-W50A12U

..........A10E analogue models

..........A11E digital continental
..........A12 E digital UK

2
 MAIN FEATURES ( V SERIES ) AT2X Chassis
Basic Functions Video Functions

TV System: B/G/H,D/K,L,I (AEP model), I/DVB-T (UK model) LCD 26”(PVA)/32”(PVA)/40”(SPVA) WXGA panel (S-LCD)
Colour System: PAL,SECAM(RF), SC3.58/4.43(Video In only) PDP 42” WVGA panel (Samsung)
HDMI Input (HD input capability) WEGA Engine ( CCPX, DRC, Panel Driver )
Component Input (HD & PAL Progressive) Picture Mode (Vivid/Standard/Custom)
Auto Channel Sorting (By Country) Wide Mode (Smart/Zoom/ 4:3/14:9/Wide)
Noise Reduction Digital Tuner:BTP-DC412Z
Teletext Page Memory 250 pages, EPG Level 2 Analog Tuner:BTF-EF412Z
Smart Link
OSD 18 languages
Picture Freeze(Analog model only) Audio Functions
Sleep Timer
1 watt STBY Power consumption
Dolby virtual Prologic2 surround
BBE digital Sound
Auto Volume Level Control
I/O Functions Sound Effect(Off/Natural/Dynamic/Dolby Virtual)

Scart Inputs (x3)

Side Input (S+V/L/R) (x1)
HDMI Input (x1) w/Audio Input(L/R)
Component Input (x1)
Audio Output (x1)
Tuner Input (x1)
Headphone (x1)
Stylish and Compact cosmetic design
digital models only
PCMCIA card slot (x1)
Modem port (x1)
Tuner output (x1)

3
 MAIN FEATURES ( W SERIES ) AT2X Chassis
Basic Functions Video Functions

TV System: B/G/H,D/K,L,I (AEP model), I/DVB-T (UK model) LCD 40” WXGA panel (S-LCD)
Colour System: PAL,SECAM(RF), SC3.58/4.43(Video In only) PDP 50” WXGA panel (NDP)
HDMI Input (HD input capability) WEGA Engine ( CCPX, DRC, Panel Driver )
Component Input (HD & PAL Progressive) Picture Mode (Vivid/Standard/Custom)
Auto Channel Sorting (By Country) Wide Mode (Smart/Zoom/ 4:3/14:9/Wide)
Noise Reduction Digital Tuner:BTP-DC412Z
Teletext Page Memory 250 pages, EPG Level 2 Analog Tuner:BTF-EF412Z
Smart Link
OSD 18 languages
Picture Freeze(Analog model only) Audio Functions
Sleep Timer
1 watt STBY Power consumption S-Master digital amplifier
100W audio output
Dolby virtual Prologic2 surround
I/O Functions BBE digital Sound
Subwoofer system
Auto Volume Level Control
Scart Inputs (x3)
Sound Effect(Off/Natural/Dynamic/Dolby Virtual)
Side Input (S+V/L/R) (x1)
HDMI Input (x1) w/Audio Input(L/R)
Component Input (x1) Sophisticated new floating cosmetic design
Audio Output (x1)
Tuner Input (x1)
Headphone (x1)

digital models only

PCMCIA card slot (x1)
Modem port (x1)
Tuner output (x1)

Differences W/V series:

Design, S-Master Audio Amplifier, Subwoofer

4
CIRCUIT BOARD LOCATION AT2X Chassis
KLV-V26A10E KDL-V26A12U
KLV-V32A10E KDL-V32A12U

A1/A2 TUNER , AUDIO SIGNAL PROCESSSING

REGULATORS, PAINTER, IN/OUT TERMINALS
AV SWITCH/ YUV SWITCH
BL VIDEO BACKEND
G2 MAIN POWER SUPPLY UNIT
H6 SWITCHES
H7 LED, SIRCS
H8 INPUT TERMINAL
KD AUDIO AMPLIFIER
N DIGITAL TV DECODING
NP1 DC-DC CONVERTERS
P HDMI INPUT
RF SPLITTER BRD

5
 CIRCUIT BOARD LOCATION AT2X Chassis
KLV-V32A10E
G2 POWER SUPPLY UNIT KD AUDIO AMPLIFIER NP1 DC-DC CONVERTER

H7 LED, SIRCS A1/A2 TUNER , AUDIO SIGNAL ROCESSSING BL VIDEO BACKEND

REGULATORS, PAINTER, IN/OUT TERMINALS
AV SWITCH/ YUV SWITCH
6
CIRCUIT BOARD LOCATION AT2X Chassis
KLV-V40A10E
KLV-V40A11E
KLV-V40A12U

A2 TUNER , AUDIO SIGNAL PROCESSSING

REGULATORS, PAINTER, IN/OUT TERMINALS
AV SWITCH/ YUV SWITCH
BL VIDEO BACKEND
G3L MAIN POWER SUPPLY UNIT
H6 SWITCHES
H7 LED, SIRCS
H8 INPUT TERMINAL
KD AUDIO AMPLIFIER
N DIGITAL TV DECODING
NP1 DC-DC CONVERTERS
P HDMI INPUT
RF SPLITTER BRD

7
 CIRCUIT BOARD LOCATION AT2X Chassis
KLV-V40A10E
G3L POWER SUPPLY UNIT KD AUDIO AMPLIFIER NP1 DC-DC CONVERTER

H7 LED, SIRCS A2 TUNER , AUDIO SIGNAL ROCESSSING BL VIDEO BACKEND

REGULATORS, PAINTER, IN/OUT TERMINALS
AV SWITCH/ YUV SWITCH
8
CIRCUIT BOARD LOCATION AT2X Chassis
KLV-W40A10E
KLV-W40A11E
KLV-W40A12U

A2 TUNER , AUDIO SIGNAL PROCESSSING

REGULATORS, PAINTER, IN/OUT TERMINALS
AV SWITCH/ YUV SWITCH
BL VIDEO BACKEND
G3L MAIN POWER SUPPLY UNIT
H1 SWITCHES
H2 INPUT TERMINAL
H3 LEDs
H4 LEDs
H5 IR RECEIVER
K AUDIO AMPLIFIER
N DIGITAL TV DECODING
NP1 DC-DC CONVERTERS
P HDMI INPUT
RF SPLITTER BRD

9
 CIRCUIT BOARD LOCATION AT2X Chassis
KLV-W40A10E

NP1 DC-DC CONVERTER K AUDIO AMPLIFIER G3L POWER SUPPLY UNIT

H1 SWITCHES

H3 LEDs
H4 LEDs

A2 TUNER , AUDIO SIGNAL ROCESSSING P HDMI INPUT BL VIDEO BACKEND

H5 IR RECEIVER REGULATORS, PAINTER, IN/OUT TERMINALS H2 INPUT TERMINAL
AV SWITCH/ YUV SWITCH

10
CIRCUIT BOARD LOCATION AT2X Chassis
KE-V42A10E
KE-V42A12U

A3 RF INPUT, TUNER , AUDIO SIGNAL ROCESSSING

DC/DC CONVERTERS
BP VIDEO BACKEND
F LINE FILTER, STBY PSU
G1 POWER FACTOR CORRECTION
G2 MAIN POWER SUPPLY
H6 SWITCHES
H7 LED, SIRCS
H8 INPUT TERMINAL
N DIGITAL TV DECODING
U I/O TERMINALS, AV SELECTOR, PAINTER
P HDMI INPUT
RF SPLITTER BRD

11
 CIRCUIT BOARD LOCATION AT2X Chassis
KE-V42A10E

G2 MAIN POWER SUPPLY BP VIDEO BACKEND G1 POWER FACTOR CORRECTION

H7 LED, SIRCS P HDMI INPUT U I/O TERMINALS, AV SELECTOR, PAINTER F LINE FILTER, STBY PSU

12
CIRCUIT BOARD LOCATION AT2X Chassis
KE-W5010E

A5 INPUT, TUNER & SIGNAL ROCESSSING

BK KIRIN BRD FOR PDP PANEL
BN VIDEO BACKEND
F LINE FILTER
G1 POWER FACTOR CORRECTION
G2N POWER SUPPLY
H1 SWITCHES
H2 AV6 I/O
H3 LED
H4 SONY LED
H5 IR RECEIVER
K AUDIO AMP
N DIGITAL TV DECODING
NP4 DC DC CONVERTER
P HDMI INPUT
RF SPLITTER BRD

13
 CIRCUIT BOARD LOCATION AT2X Chassis
KE-W5010E

G2N POWER SUPPLY BN VIDEO BACKEND BK KIRIN BRD FOR PDP PANEL K AUDIO AMP

G1 POWER FACTOR CORRECTION F LINE FILTER P HDMI INPUT A5 INPUT, TUNER & AUDIO SIGNAL PROCESSSING

14
 26” LCD PANEL DESCRIPTION AT2X Chassis
General Description

LTA260W2- is a color active matrix TFT (Thin Film Transistor) liquid crystal display (LCD) that uses amorphous silicon TFTs as a switching devices.
This model is composed of a TFT LCD panel, a driver circuit and a back-light system.
The resolution of a 26.0" contains 1366 x 768 pixels and can display up to 16.7 million colors with wide viewing angle of 89° in all directions.

Features

WXGA(1366 x 768 pixels) resolution (16:9)

High contrast ratio, high aperture structure ( Contrast Ratio 1000 :1 )
Luminance of White: 500 cd/m2
APVA(Advanced Patterned Vertical Align) mode
Wide viewing angle: 89/89/89/89
High speed response: 8msec (G/G)
Number of Colors: 16.7M
Low Power consumption
8 U-type CCFL( Cold Cathode Fluorescent Lamp)
Interface: LVDS(Low-Voltage Differential Signal) interface.(1pixel/clock)
Pixel arrangement RGB Vertical Stripe
Pixel pitch 0.4215(H) × 0.4215(W)

Applications

Home-alone Multimedia TFT-LCD TV

Display terminals for AV application products
High Definition TV (HD TV)

15
 32” LCD PANEL DESCRIPTION AT2X Chassis
General Description

LTA320W2- is a color active matrix TFT (Thin Film Transistor) liquid crystal display (LCD) that uses amorphous silicon TFTs as a switching devices.
This model is composed of a TFT LCD panel, a driver circuit and a back-light system.
The resolution of a 32.0" contains 1366 x 768 pixels and can display up to 16.7 million colors with wide viewing angle of 89° in all directions.

Features

WXGA(1366 x 768 pixels) resolution (16:9)

High contrast ratio, high aperture structure ( Contrast Ratio 1000 :1 )
Luminance of White: 500 cd/m2
APVA(Advanced Patterned Vertical Align) mode
Wide viewing angle: 89/89/89/89
High speed response: 8msec (G/G)
Number of Colors: 16.7M
Low Power consumption
16 Direct Type CCFL( Cold Cathode Fluorescent Lamp)
Interface: LVDS(Low-Voltage Differential Signal) interface.(1pixel/clock)
Pixel arrangement RGB Vertical Stripe
Pixel pitch 0.648(H) × 0.648(W)

Applications

Home-alone Multimedia TFT-LCD TV

Display terminals for AV application products
High Definition TV (HD TV)

16
 40” LCD PANEL DESCRIPTION AT2X Chassis
General Description

LTA400W2- is a color active matrix TFT (Thin Film Transistor) liquid crystal display (LCD) that uses amorphous silicon TFTs as a switching devices.
This model is composed of a TFT LCD panel, a driver circuit and a back-light system.
The resolution of a 40.0" contains 1366 x 768 pixels and can display up to 16.7 million colors with wide viewing angle of 89° in all directions.

Features

WXGA(1366 x 768 pixels) resolution (16:9)

High contrast ratio, high aperture structure ( Contrast Ratio 1000 :1 )
Luminance of White: 500 cd/m2
APVA(Advanced Patterned Vertical Align) mode
Wide viewing angle: 89/89/89/89
High speed response: 8msec (G/G)
Number of Colors: 16.7M
Low Power consumption
20 Direct Type CCFL( Cold Cathode Fluorescent Lamp)
Interface: LVDS(Low-Voltage Differential Signal) interface.(1pixel/clock)
Pixel arrangement RGB Vertical Stripe
Pixel pitch 0.648(H) × 0.648(W)

Applications

Home-alone Multimedia TFT-LCD TV

Display terminals for AV application products
High Definition TV (HD TV)

17
 42” PDP PANEL DESCRIPTION AT2X Chassis
DESCRIPTION

The S42SD-YD07 is a 42-inch wide full color plasma display module with a resolution of 852(H) × 480(V) pixels.
The display module includes Display Panel, Panel driving electronics, and Logic controller.

FEATURES
- Wide aspect ratio(16:9) 42 inch diagonal display screen. The display area is 932.94mm wide and 532.80mm high.
- Slim and light weight. The display module is 66.4? in depth and weights only approx.18.2mm include power supply.
- 1073.7 million colors(10Bit), 16.77 million colors(8Bit) combination of R,G and B digital data
- High brightness, High contrast, Wide viewing angle. The screen has a white peak brightness of typical 1200 cd/m2,
contrast of typical 5000:1 and a viewing angle of greater than 160° comparable to that achievied with CRTs.

FUNCTION OUTLINE

- The PDP module has APC(Automatic Power Control) function which restrict power consumption within certain value with regard to each display load ratio.
- The PDP module is operated by following digital video signals; Vertical synchronous signal, Horizental synchronous signal and 8bits data signal of each R,G, and B color.
All signals are based on LVDS level.
- The PDP module is operated at 50HZ or 60Hz frame rate. It is required external frame rate conversion in order to display the other formats.
- The PDP module requires several types of input voltage; voltage for driving logic board , FET in driving board, sustain, address, reset, scan and x-bias.
- The PDP module is operated at progressive signal only. It is required external progressive scan conversion in order to display the other formats.

Display Performance

- Display Pixels Horizontal 852 × Vertical 480 pixels (1 pixel = 1 R,G,B cells)
- Number of Color 1073.7 million colors(10Bit), 16.77 million colors(8Bit)
- Brightness (Peak Brightness) - NTSC/PAL : Minimum 1000 cd/?, Typical 1,200 cd/?
- Brightness (Full white Brightness) NTSC / PAL : Minimum 180 cd/?, Typical 200 cd/?
- Contrast Ratio (in dark room) - NTSC/PAL : Minimum 4,500:1, Typical 5,000:1
- Power consumption TYP 240W

18
42” PDP PANEL BLOCK DIAGRAM AT2X Chassis

19
 50” PDP PANEL DESCRIPTION AT2X Chassis
DESCRIPTION
The NP50X6MF02 is a 50-inch wide colour plasma display with a resolution of 1365(H) x 768(V).
This device can operate with 8-bit, 9bit or 10bit of digital video signal for each RGB colour, video synchronous signals, display mode control signal and 3 kinds of DC power sources.
This display has a PLE ( Peak Luminance Enhancement ) function that adjusts the luminance and contrast to the suitable value in accordance with the input video signal level variance,
so that image can be displayed with the ideal luminance and contrast.
The device has a False Contour Reduction ( FC ) function and 3 kinds of video image processing functions ( colour space conversion, inverse gamma correction and error diffusion ).
The False Contour Reduction ( FC ) function or the video image processing functions can be selected exclusively according to the external command.

BASIC CONFIGURATION

Color Inverse
Error FC Reduction
RA-, RA+ space gamma
diffusion Control
RB-, RB+ conversion correction
RC-, RC+
RD-, RD+
RE-, RE+ ON/OFF ON/OFF ON/OFF ON/OFF
RF-, RF+ I/F
RG-, RG+ Circuit
RH-, RH+ Frame
RCLK- memory
RCLK+ ON/OFF

PS-, PS+
Control
ALARM
circuit
MSEL

Data driver
LVP

Vs

Vd Scan Color plasma Scan

driver display panel driver
Vcc

Data driver

20
 SERVICE CONCEPT AT2X Chassis
ANALOG MODELS

SERIES W V
SIZE 50" 40" 42" 40" 32" 26" When replaced
PANEL PDP LCD PDP LCD LCD LCD Service concept CCT's in SM needs adjustment
HDMI IN P P P P P P REPLACE NO NO
H BOARD H2 H8 REPAIR YES NO
H BOARDS H1/H3/H4/H5 H6/H7 REPAIR YES NO
AUDIO AMPL K KD REPLACE NO NO
VIDEO BACKEND BN BL BP BL REPLACE NO YES
INPUT & TUNER A5 A2 A3 A2 A1 REPAIR YES YES
REPAIR YES YES
POWER SUPPLY F,G1,G2N G3L F,G1,G2 G3L G2 (same as WAX) (except PDP42) (except PDP42) (only for PDP)
DC DC CONV NP4 NP1 N/A NP1 NP1 NP1 REPAIR YES NO
KIRIN BOARD FOR PDP BK N/A N/A N/A N/A N/A REPLACE NO NO
J ( EXTENSION ) N/A N/A N/A J2 N/A N/A REPLACE NO NO

DIGITAL MODELS

SERIES W V
SIZE 50" 40" 42" 40" 32" 26" When replaced
PANEL PDP LCD PDP LCD LCD LCD Service concept CCT's in SM needs adjustment
DIGITAL TV N REPAIR YES NO
SPLITTER RF REPLACE NO NO
HDMI IN P P P P P P REPLACE NO NO
H BOARD H2 H8 REPAIR YES NO
H BOARDS H1/H3/H4/H5 H6/H7 REPAIR YES NO
AUDIO AMPL K KD REPLACE NO NO
VIDEO BACKEND BN BL BP BL REPLACE NO YES
INPUT & TUNER A5 A2 A3 A2 A1 REPAIR YES YES
REPAIR YES YES
POWER SUPPLY F,G1,G2N G3L F,G1,G2 G3L G2 (same as WAX) (except PDP42) (except PDP42) (only for PDP)
DC DC CONV NP4 NP1 N/A NP1 NP1 NP1 REPAIR YES NO
KIRIN BOARD FOR PDP BK N/A N/A N/A N/A N/A REPLACE NO NO
J ( EXTENSION ) N/A N/A N/A J2 N/A N/A REPLACE NO NO

21
 POWER SUPPLY UNIT AT2X Chassis

NP1
KLV-V26/32A10E analogue model
KDL-V26/32A11E G2 board A1 board
KDL-V26/32A12U NP1
digital models

G2, G3L BOARD (LCD TV)

LINE FILTER, STBY PSU, PFC, MAIN PSU, SUB PSU
NP1
KLV-V40A10E analogue model NP1, NP4 BOARD
G3L board DC-DC CONVERTERS
KDL-V40A11E A2 board
KDL-V40A12U NP1
digital models
A1, A2, A3, A5 BOARD
DC-DC CONVERTOR, REGULATORS

F BOARD
LINE FILTER, STBY PSU (..V42.)
NP1
KLV-W40A10E analogue model G1 BOARD (PDP TV)
KDL-W40A11E G3L board PFC CIRCUIT, STBY PSU (.. W50A.)
A2 board
KDL-W40A12U NP1
digital models
G2, G2N BOARD(PDP TV)
MAIN PSU

KE-V42A10E
F board G1 board G2 board A3 board
KDE-V42A12U

KE-W50A10E
KDE-W50A11E F board G1 board G2N board NP4 board
A5 board
KDE-W50A12U

22
 POWER SUPPLY UNIT AT2X Chassis
KLV V26/32A1...
KLD V26/32A1...

G2 BOARD BLOCK DIAGRAM

AC RLY IC6502, L6502,Q6500

RY6004

DC 395V
LFC Bridge-diode T6100,6101,
L6000, 6001 D6000 R6102 IC6100, Q6100,6101

AC RESISTOR UNREG 33V

LINE
RECTIFIER PFC FUSE
AC IN FILTER
CONVERTER REG 17.5V
100/240V MAIN
OCP, OVP CONVERTER
UNREG 10.5V

Au 15V
OCP, OVP

SW
Q6400
POWER ON

AC STBY
RESISTOR CONVERTER
STBY 5V
RECTIFIER OCP, OVP

Bridge-diode R6300
D6300 IC6300,T6300

23
 POWER SUPPLY UNIT AT2X Chassis
KLV V26/32A1...
KLD V26/32A1...
G2 BOARD POWER ON sequence

AC IN

STBY PSU ON

LOW
POWER ON AC RLY RY6004 OFF PFC CONVERTER OFF STANDBY MODE
CN6203 3pin VCC SW Q6400 OFF MAIN PSU OFF

HIGH

AC RLY RY6004 ON
VCC SW Q6400 ON

PFC CONVERTER ON
MAIN PSU ON

ON MODE

24
 STBY POWER SUPPLY UNIT AT2X Chassis
KLV V26/32A1...
KLD V26/32A1...
STBY PSU BLOCK DIAGRAM

G2 BOARD STBY PSU

25
 STBY POWER SUPPLY UNIT AT2X Chassis
KLV V26/32A1...
KLD V26/32A1...
G2 BOARD STBY PSU TROUBLESHOOTING

STBY PSU FAILURE

VCC CHECK FEEDBACK CHECK

FUSE RESISTOR
CHECK

IC6300 PIN 2 IS HIGHER IC6300 PIN 4 IS HIGHER PRIMARY Vcc CCT FAILURE,
NO NO NO
R6300 OPEN? THAN 30V THAN 7V T6300 PIN3-4 WINDING,
DURING START UP? DURING START UP? R6307, D6303 CHECK

YES YES YES

IC6300, C6305, SECONDARY CCT FAILURE SECONDARY CCT SHORTED

T6300 PRIMARY PH6300, IC6301 & T6300 SECONDARY WINDING,
WINDING SHORTED SURROUNDING CCT CHECK D6305, C6314 &
SURROUNDING CCT CHECK

26
 POWER SUPPLY UNIT AT2X Chassis
KLV V26/32A1...
KLD V26/32A1...
G2 BOARD TROUBLESHOOTING

NO
PICTURE/SOUND

NO NO NO GO TO
STBY LED F6000 (AC FUSE) R6300 OPEN? STBY PSU FAILURE STBY PSU
ON/BLINK? OPEN? TROUBLESHOOTING

YES YES YES

VD6000 IC6300
C6002/6004 SHORTED? (STBY IC) FAILURE
Q6500 CHECK

NO
BLINKS YES
BLINKS THE LED FAUILURE EXCLUDING PSU
STBY LED? 3 TIMES?

YES

NO
PSU FAILURE GO TO MAIN PSU TROUBLESHOOTING

CN6203 PIN 3 HIGH RY6004 NO

STBY_5V LINE CHECK, RELAY ON CIRCUIT CHECK
(POWER ON) (AC Relay)
ON ?

LOW YES

µPC (H8)
PFC FAILURE GO TO PFC TROBLESHOOTING
CIRCUIT FAILURE

27
 POWER SUPPLY UNIT AT2X Chassis
KLV V26/32A1...
KLD V26/32A1...
PFC CIRCUIT BLOCK DIAGRAM

DC 395V

POWER ON

28
 POWER SUPPLY UNIT AT2X Chassis
KLV V26/32A1...
KLD V26/32A1...
G2 BOARD PFC CIRCUIT TROUBLESHOOTING

PFC CONVERTER FAILURE

PFC OUTPUT
IC6502, 6503 OVP works.
VOLTAGE CHECK INSTANTANEOUSLY INCREASES UP TO APPROX. 450V
C6008 VOLTAGE R6545, 6546, 6547, 6548,
APPROX. 395V? 6549, 6550, 6557 open
or IC6502 failure

APPROX.325V AT AC 230V INPUT

PFC CONTROL IC
VCC VOLTAGE CHECK

NO IS THE VOLTAGE NO NO T6300 PIN 1-2

IS THE PIN 8 IC6502 R6308 OPEN?
AT C6310 APPROX.18V? WINDING OPEN
APPROX. 17V?

YES
YES

YES
CHECK Q6400,Q6401, CHECK PH6400,
PH6400, R6551 D6304, C6314
PFC CONTROL IC
SWITCHING
CONFIRMATION
IC6502 FAILURE,
IS THE RECTANGLE VOLTAGE NO
L6502 PIN10-11
AT PIN 7 IC6502 AVAILABLE? WINDING OPEN

YES

CHECK Q6501,
Q6502, R6538

29
 POWER SUPPLY UNIT AT2X Chassis
KLV V26/32A1...
KLD V26/32A1...
MAIN PSU CIRCUIT BLOCK DIAGRAM

30
 POWER SUPPLY UNIT AT2X Chassis
KLV V26/32A1...
KLD V26/32A1...
G2 BOARD MAIN PSU CIRCUIT TROUBLESHOOTING

MAIN PSU FAILURE

FUSE RESISTOR CHECK STBY PSU CHECK

NO NO NO CHECK R6308, C6310, D6304

IS THE PIN 15 IC6100 R6101 OPEN? HAS C6310 18V?
APPROX. 17V? T6300 PIN1-2 WINDING OPEN

MAIN CONTROL IC
VCC VOLTAGE CHECK YES YES

IC6100 15 PIN SHORTED CHECK FOLLOWINGS:

CHECK Q6400,
OR SECONDARY RECTIFIER CCT,
YES Q6401, PH6400
C6102 SHORTED T6100, T6101, PH6100,
IC6200 SURROUNDING CCT

SWITCHING CHECK PROTECTOR CHECK

FUSE RESISTOR
CHECK YES
HAS THE PIN 3 IC6100 YES YES IS PIN12 IC6100
NO HAS PIN20 IC6100
R6102 OPEN? TRIANGLE SHAPE VOLTAGE RECTANGLE SHAPE VOLTAGE HIGHTER THAN 3V
DURING START UP? DURING START UP?

YES
NO NO NO

Q6100, Q6101 & Q6100, Q6101 & PH6100 and

IC6100, C6104,
SURROUNDING CCT, SURROUNDING CCT, SURROUNDING CCT,
R6111 FAILURE
IC6100 CHECK IC6100 CHECK IC6100 CHECK

31
 POWER SUPPLY UNIT AT2X Chassis
KLV V40A... KDL V40A..
KLV W40A... KDL W40A
G3L BOARD BLOCK DIAGRAM

IC6100, IC6420, L6102,L6104

AC RLY Q6105, Q6106, Q6106
RY6002

DC 380V
LFC Bridge-diode T6100,6101,
L6002 D6104 R6501 IC6500, Q6500,6501

AC RESISTOR 17,5V
LINE
RECTIFIER PFC FUSE
AC IN FILTER TO PANEL
CONVERTER
100/240V MAIN ( INVERTER )
CONVERTER
OCP, OVP

OCP, OVP

T6700,IC6700,
SW R6701 Q6700,6701
AC RLY
Q6430
RESISTOR TU 32V
FUSE
SUB SUB 17.5V
CONVERTER
SUB 11V

AU 22V
OCP, OVP

AC STBY
RESISTOR CONVERTER
STBY 5V
RECTIFIER OCP, OVP

Bridge-diode R6300
D6300 IC6300,T6300

32
 POWER SUPPLY UNIT AT2X Chassis
KLV V40A... KDL V40A..
KLV W40A... KDL W40A
G3L BOARD POWER ON sequence

AC RLY(3pin) SET
Turn on STBY SUB Source Stand-by
AC IN CN6201
Source OFF Mode
G3L LOW

HIGH

Turn on AC RELAY
RY6002
G3L

Turn on
Main,Sub & Conv,PFC
G3L

Turn on SW
POWER2(PANEL 5V)
POWER 3(D3.3V)
LOW
POWER 4(D5V

HIGH
Only Use Digital Model
REC ON(12pin) Turn on
N5V CONT(18pin) Digital
CN5804 at NP1 Tuner

Supply
PANEL 5V
D3.3V
D5V & REG5V
A2 board

Only Use Digital Model

Active
BACK LIGHT LOW
Panel Back Light OFF Stand-by
CN1004(2pin)
BL board Mode

HIGH

Turn On
SET
33
 POWER SUPPLY UNIT AT2X Chassis
KLV V40A... KDL V40A..
KLV W40A... KDL W40A
PSU TROUBLE SHOOTING

THE FOLLOWING TROUBLE SHOOTING MANUALS ARE AVAILABLE IN ADDITIONAL FILE.

- GENERAL PSU TROUBLE SHOOTING

- STBY SOURCE ANALYSIS
- G3L CONVERTERS TROBLE SHOOTING
- G3L PFC TROUBLE SHOOTING
- NP1 TROUBLE SHOOTING
- FAN ERRORS TROUBLE SHOOTING

34
 POWER SUPPLY UNIT AT2X Chassis
KE-V42A10E
KDE-V42A12U
BLOCK DIAGRAM & SERVICE POLICY

F BOARD G1 BOARD G2 BOARD A3 BOARD

F BOARD G1 BOARD G2 BOARD A5 BOARD

LINE FILTER, STBY PSU PFC CIRCUIT MAIN PSU DC-DC CONVERTOR, REGULATORS

IMPORTANT NOTE:

Power Supply Boards: F, G1and G2 are not designed to be repaired on components level.
Schematic Diagrams and Spare Parts numbers are not available in Service Manual.

In case of PSU failure, the complete board has to be exchanged.

Always, when a PSU board will be replaced, the PDP voltages should be controlled/adjusted (see next page)

35
 POWER SUPPLY UNIT AT2X Chassis
KE-V42A10E
KDE-V42A12U
PDP voltage adjustment

(1) Input white full field signal in Video input. (1) VIDEO PAL 100% white full field signal

(2) Each voltages should be adjusted with RVs listed in TABLE1. (2) PDP voltage standard
within the standard of right column. Items Standard
To monitor the voltages, use CN6411(PICTURE 2) VS (The voltage described in back label of PDP ) +-0.5V
VSET (The voltage described in back label of PDP ) +-0.5V
RV Items VE (The voltage described in back label of PDP ) +-0.5V
RV6801 CN6411(1pin) VS VA (The voltage described in back label of PDP ) +-0.5V
RV6804 CN6411(2pin) VSET VSCAN (The voltage described in back label of PDP ) +-0.5V
RV6802 CN6411(3pin) VE
RV6601 CN6411(4pin) VA * Use pin#6 of CN6411 as GND.
RV6803 CN6411(8pin) VSCAN
TABLE1 : RVs for voltage adjustment Note : Every voltage should be adjusted according to the label on the back of PDP.

PICTURE 1 : Positions of RVs PICTURE 2 : Connector to monitor

Typical adjustment voltage as reference

ItemsRef. Voltage
VS 209V Note : The table shows typical
VSET 198V adjustment voltage.
VE 82V
VA 70V
VSCAN -180V
36
 POWER SUPPLY UNIT AT2X Chassis
KE-W50A10E
KDE-W50A11/12
BLOCK DIAGRAM

Line AC DC 380V
VS 190V for PDP
Filter SW Rectifier PFC VS
RY6001 Converter Converter
Floating Vcc 18V
STBY
F Board Converter 5V
STBY 5V
G1 Board

VD 70V for PDP

VD
380V
Converter
18V
Discrete Tuner VC 32V
Regulator
18V
Audio 25V
Not used on W50
Linear
Thru 5V
380V 33V Regulator
VC 25V
Converter Sub 6.5V
6.5V
Sub 11V
11V
Vcc 18V 11V Linear
SW 9V
Regulator
Vcc 5V for PDP
Vcc DC/DC
Converter
FAN
G2N Board FAN 7V
Drive

37
 POWER SUPPLY UNIT AT2X Chassis
KE-W50A10E
KDE-W50A11/12
DESCRIPTION OF POWER SUPPLY BOARDS.

F BOARD
AC Fuse, Line Filer circuit

G1 BOARD
*Standby converter (Ringing Chock Converter), Main Power Relay, AC Rectifier,
* PFC circuit (Phase Factor Correction) Pulse Width Modulation converter

G2N BOARD
*VC converter: EX-Z Power Supply System (Current resonance converter) VCC5V for Logic power of PDP.
11V, 6.5V, SW_9V, THRU_5V for Signal part power source and FAN_7V, 32V for tuner VC, 26V for the Audio amplifier.

*VD/VA converter: the power source for the data/address of PDP EX-Z Power Supply System (Current Resonance converter)

*VS converter: the power source for the sustain of PDP EX-Z Power Supply System (Current Resonance converter)

38
 POWER SUPPLY UNIT AT2X Chassis
KE-W50A10E
AC IN KDE-W50A11/12

POWER ON SEQUENCE

STBY CONVERTER ON
STBY 5V OUTPUT

AC RELAY NO VCC5V DC/DC

CN6901 PIN 3 "H" STANDBY MODE
CONVERTER ON
G1 Board
YES

AC RELAY VS CONVERTER
RY6001 ON ON

PFC CONVERTER VS OUT NO

ON MORE THAN NO PICTURE
150V?

YES
VC CONVERTER ON
32V/26V/11V/6.5V
Thru 5V OUT VD CONVERTER
ON

PFC OUT NO
MORE THAN
NO PICTURE PICTURE APPEARS
350V?

YES
SW 9V

PANEL ON NO
CN6004 PIN10 "H"?

YES 39
 POWER SUPPLY UNIT AT2X Chassis
KE-W50A10E
KDE-W50A11/12
POWER ON SEQUENCE

PSU VOLTAGES SEQUENCE

40
 POWER SUPPLY UNIT AT2X Chassis
KE-W50A10E
KDE-W50A11/12
POWER SUPPLY TROUBLE SHOOTING

No Picture

Standby LED NO F6001(AC Fuse) NO NO Standby Rectifier Diode

R6102 Open?
(Red) Light or Open ? G1 board Check Secondary circuit
Blinking ? F board of Standby5V line

YES YES YES

VD6001/6002 or
IC6101
C6002/6004 short?
(Stby IC) Fail
Q6206/6207/6219

Standby LED YES

PLEASE CHECK ERROR CODE LIST
(Red) Blinking ?

NO

Power LED CN6004 pin3 RY6001 Check

NO NO NO
(Green) (AC_RLY) Low ? (AC Relay) Standby 5V line
Light ? G2 board ON ?

YES YES
YES

around micro fail

PFC circuit fail
on BN board

PDP module YES Check each DC/DC Check Signal

Priming ? converter out Processes circuit
OK?
NO

Check XY
PDP fail
Main Panel
41
 POWER SUPPLY UNIT AT2X Chassis
KE-W50A10E
KDE-W50A11/12
PFC CONVERTER TROUBLE SHOOTING

PFC converter fail

on G1 board
(Vout<350V)

PFC out
PFC out NO NO IC6202 pin15 NO NO Standby
CN6017 pin5 CN6017 pin2
CN6017 pin5 12V ? PRI_VCC 18V fail
200V<Vout<350V ? More than 15V?
Vout<10V?

YES YES YES YES

Please check F6001 IC6202 pin16 NO When turn ON NO

Re Adjust for RV6201
R6005/6006/6007 pulse waveform IC6203 pin14 Check IC6201
Check RV6201,IC6202
Q6206/6207/6219 appear? “H” ?

YES YES

PFC OVP operate

Check R6233 Check R6249
Q6203/6205 ~RV6201

Check IC6202

42
 POWER SUPPLY UNIT AT2X Chassis
KE-W50A10E
KDE-W50A11/12
VC CONVERTER TROUBLE SHOOTING

VC converter fail
on G2 board

When
NO turn on IC6301 pin3 NO IC6301 pin15 NO CN6017 pin2 NO Check Standby
R6302 Open saw waveform appear? more than 15V ? more than 15V? Power Supply

YES YES YES YES

Check R6301,
R6316
Q6301,Q6302
Fail *1
When turn on
IC6301 pin20 NO IC6301 pin1 NO IC6301
pulse waveform appear? more than 1.4V Fail
*1 If Q6301 and Q6302 fail
Must be change D6306 and D6307 YES YES

3V

Pin 12 IC6301 pin12 NO IC6301 or

more than 3V ? PH6401,IC6405 fail.
Shut Down
YES

IC6301 OCP operate

VC Secondary side
short circuit.

43
 POWER SUPPLY UNIT AT2X Chassis
KE-W50A10E
KDE-W50A11/12
VD CONVERTER TROUBLE SHOOTING

VA converter fail
on G2 board

When
NO turn on IC6501 pin3 NO IC6501 pin15 NO C6315 NO VC converter
R6503 Open?
saw waveform appear? more than 15V ? more than 15V? or Vcc line fail

YES YES YES YES

Check R6502
Q6503,Q6504
Fail *1
When turn on
IC6501 pin20 NO IC6501 pin1 NO Q6918&Q6909 YES Check
pulse waveform appear? more than 1.4V C “H” ? PH6905,Q6502

*1 If Q6503 and Q6504 fail

Must be change D6506 and D6507 YES YES
NO

3V

IC6501 pin12 NO IC6501 or Check PFC or

Pin 12 PFC out NO
more than 3V ? PH6601,IC6601 fail. re Adjustment
more than 350V ?
PFC Voltage
Shut Down
YES
YES

IC6501 OCP operate

Check
VA Secondary side VCC5V YES
around Q6926,
short circuit. OK ?
IC6905

NO

Check IC6408,
44 Q6406
 POWER SUPPLY UNIT AT2X Chassis
KE-W50A10E
KDE-W50A11/12
VS CONVERTER TROUBLE SHOOTING

VS converter fail
on G2 board

When
NO turn on IC6701 pin3 NO IC6701 pin15 NO C6315 NO VC converter
R6703 Open?
saw waveform appear? more than 15V ? more than 15V? or Vcc line fail

YES YES YES YES

Check R6702
Q6705,Q6706
Fail *1
When turn on
IC6701 pin20 NO IC6701 pin1 NO Q6909 C YES Check
pulse waveform appear? more than 1.4V “H” ? PH6903,Q6702

*1 If Q6705 and Q6706 fail

Must be change D6707 and D6708 YES YES
NO

3V
IC6701 pin12 NO IC6701 or Check PFC or
Pin 12 PFC out NO
more than 3V ? PH6801,IC6801 fail. re Adjustment
more than 350V ?
PFC Voltage
Shut Down
YES
YES

IC6701 OCP operate

Check
VA Secondary side VCC5V YES
around Q6926,
short circuit. OK ?
IC6905

NO

Check IC6408,
45 Q6406
 POWER SUPPLY UNIT AT2X Chassis
KE-W50A10E
KDE-W50A11/12
G1 / G2N VOLTAGE ADJUSTMENT

In case that G1 and G2 boards need to be adjusted ( e.g. after replacement or repair )please apply the following:
Note as boards arrive pre-adjusted it is hoped readjustment of these boards is rarely required.

1. Adjust G1Board PFC Output voltage using RV6201 until the output is at 380V (Do not adjust above this level).

2. Adjust VD Voltage to the level specified by panel label at top left side of panel - normally 70V using RV6601.

3. Adjust VS Voltage to the level specified by panel label at top left side of panel - normally 190V using RV6801.

46
 I2C BUS MAP AT2X Chassis
IC1005 B BOARD A BOARD
M24C64 SCL_D/SDA_D
EEPROM CN1001/ (5V)
IC4403
CN 5102
SAA5665HL/M
IC1004 100P
PAINTER 2
RV5C87A (A35/B35)
RTC Level Conv SCL_P2/SDA_P2
SCL_D/SDA_D (5V)
IC1009 (3.3V)
PCA9555DB #75 : SCL_D IC4102 IC4402 TU4920 IC5201
I/O Expander #76 : SDA_D MSP4411K M24C16 TUNER CXA2069
SCL_A/SDA_A NICAM EEPROM AV SW
(3.3V) #77 : SCL_A(NVM)
CN1006 Level Conv
#78 :SDA_A(NVM)
IC 1002
HD64F2378
SCL_0/SDA_0 H8/2378
IC1302
(3.3V) #137 : SCL_0_400K
CXD3807GD
#138 : SDA_0_400K
CCPX SCL_B/SDA_B
(5V) CN4606
#73 : SCL_B P board P BOARD
IC2002 #74 :SDA_B HDMI
CXD9756R
Bolt/Thunder SCL_B/SDA_B IC4807
(3.3V) CXA2171
Comp SW
IC1305
SM5302AS
LPF (CVBS)
IC4103
IC1307 CXD9826
SM5302AS Delay
CN1003/
LPF (YUV) CN 4604 CN5101
Level Conv
20P K board
K BOARD
(#11/#12)

CN 1009 IC 1008 IC1702 SCL_B/SDA_B CN1001/ SCL_B/SDA_B

LM75CIMX-3 CDX2097 (3.3V) CN5101
(3.3V) CN 5102
Thermo Sensor DRC 100P
N Board N BOARD
IDTV
(A37/B36)

47
 MICROPROCESSORS AND THEIR FUNCTIONS AT2X Chassis

B BOARD - BACK END A BOARD - ANALOG FRONT END

EEPROM
MSP TUNER
EEPROM AV SW
4411K
RTC
PW166
IIC(100k)
I/O
Expander
UART
SAA 5665HL/M
IIC(400k) IIC(100k) PAINTER 2

IIC(100k)
CCPX HITACHI
H8S/2378 N BOARD - DIGITAL FRONT END

Bolt/
EMMA 2 Lite
Thunder

LPF
(CVBS)
IIC(100k)

LPF
(YUV)

Thermo Comp P board

DRC S-Master Delay
Sensor SW HDMI

48
 MICROPROCESSORS AND THEIR FUNCTIONS AT2X Chassis

How to find out the software version of each processor?

The software versions can be checked in Service Menu

How to upgrade the software?

H8 Processor - using TL JIG
PW Processor - using TL JIG
PAINTER 2 Processor - change the OTP IC on A board
HITACHI H8S/2378 Main / System control ( B BOARD )
EMMA Processor - using PCMCI
- User Interface
- Analogue OSD/Menu control
- Total management of all the microprocessors
- Audio Amp, Chroma decoder, Combfilter, N board

PW 166 Scaler / OSD ( B BOARD )

- Signal scaling for all the video format
- Analogue OSD/Menu indication

SAA5665HL/M PAINTER2 Analogue FE ( A BOARD )

- Analogue Tuner control
- AV Switch control
- SmartLink and the other special control in SCART terminals
- Audio processor (MSP device)

EMMA2 Lite Digital FE ( N BOARD )

- Digital Tuner control
- Digital menu control/Indication
- Digital EPG
- MHEG application management
- (MHP application for continental)
EMMA PROCESSOR is available only in digital models

49
 SELF DIAGNOSTIC SOFTWARE 1/2 AT2X Chassis
If a device is found to be faulty the relevant device number will be displayed through the LED (Series of flashes which must be counted).

Flash Timing Example : e.g. error number 3

STBY LED

LED ERROR ERROR DESCRIPTION Comments

CODE
01 Sub Woofer detection LED only
02 Temperature error. ( Read data from LM75 ) Shutdown & LED
03 Main power voltage error. (REG9V_ALERT) Shutdown & LED
04 FAN error Shutdown & LED
05 PIxelWork communication error (No ACK) Shutdown & LED
06 3.3V voltage error Shutdown & LED
07 Audio Thermo-protection/Speaker Protection Shutdown & LED
08 Panel 5V error Shutdown & LED
09 Panel Alarm Shutdown & LED
10 Power Supply Protetcion (PS_PROT) Shutdown & LED
11 Over Voltage Protection (OVP) Shutdown & LED
12 IIC_B - IIC B Clock Error LED only
13 IIC_D - IIC D(Painter)Clock Error LED only
14 IIC_A - IIC A(NVM)Clock Error LED only
15 IIC_0 - IIC 0 400k Clock Error LED only

50
 SELF DIAGNOSTIC SOFTWARE 2/2 AT2X Chassis

ITEM H8 Pin No FUNCTION Shutdown Condition LED Comments LCD PDP

V W V W
26” 32” 40” 40” 42” 50”
ON ON ON ON ON ON

PixelWorks I2C PW communication error No ACK from PW 5 Shutdown & LED YES YES YES YES YES YES
Backlight #119 Backlight error Panel_Det < 0.65V 9 Shutdown & LED YES YES YES YES NO NO
Main Power #117 Main Power voltage error REG_9V_Alert 3 Shutdown & LED YES YES YES YES YES YES
3.3V #124 3.3V voltage error 3.3V_Alert<1.66V 6 Shutdown & LED YES YES YES YES YES YES
5V #123 5V error 5V_Alert<1.66V 6 Shutdown & LED YES YES YES YES YES YES
Panel 5V #115 Panel 5V error P5V DET< 1.84V 8 Shutdown & LED YES YES YES YES NO NO
P5V DET > 2.25V
Fan error #33 Fan error Fan error >=1.66V(H) 4 Shutdown & LED NO YES YES YES YES YES
Temperature I2C Temp Error Read from LM75 2 Shutdown & LED YES YES YES YES YES YES
Panel Alarm #53 Panel Alarm . Only recover Panel_Alarm < 1.66V (L) 9 Shutdown & LED NO NO NO NO NO YES
when AC pull Out=>In
Audio #26 Audio AMP protection Thermal_Protect<1.66V (L) 7 Shutdown & LED YES YES YES NO YES NO
Thermo-protection
Speaker Protection #132 Audio AMP protection THERMAL/DC DET/OCP/ 7 Shutdown & LED NO NO NO YES NO YES
LVP/PROTECT< 0.9V(LOW)
PS Protection #82 PS_PROT PS_PROT < 1.6V(L) 10 Shutdown & LED NO NO NO NO NO YES
11sec after Power-Up
OVP #90 OVP signal OVP>1.6V 11 Shutdown & LED NO NO NO NO NO YES
Sub Woofer Det Port Exp Sub Woofer Detection WFR_DET = H, Detect 1 LED only NO NO NO YES NO YES
only when Speaker is ON
IIC_B #73,#74 IIC B Clock Error SCL_B=L 12 LED only YES YES YES YES YES YES
IIC_D #75, #76 IIC D(Painter) Clock Error SCL_D=L 13 LED only YES YES YES YES YES YES
IIC_D #77, #78 IIC A(NVM)Clock Error SCL_A=L 14 LED only YES YES YES YES YES YES
II_0 #137, #138 IIC 0 400k Clock Error SCL_0_400k=L 15 LED only YES YES YES YES YES YES

51
 NVM VARIETY & BOARD REPLACEMENT AT2X Chassis
Series W V

Size 50" 40" 42" 40" 32" 26" How Service can READ/WRITE NVM content
Panel PDP LCD PDP LCD LCD LCD
Digital TV N Board 1 NVM automaticly written ny EMMA when empty
( PCMCI for Flash code)
Splitter RF Board NO NVM N/A
HDMI input P Board 1 EDID data written in BCN (HDCP)
H boards (side input) H2,8 NO NVM N/A
H boards H1,3,4,5,6,7 NO NVM N/A
Audio Ampl K, KD Board 1 NO NVM NVM data written in BCN
Video Backend boards BN,BL26, BL32, BP 1 NVM data automatic written by main micro when empty
Also possible to read/write by TL board
Input & Tuner A5,2,1,3 Boards 1 NOT POSSIBLE
( just reset and set up default values )
Power Supply F,G1,G2N... NO NVM N/A
DC DC Conv NP1,4 Boards NO NVM N/A
KIRIN board for PDP panel BK NO NVM N/A

P BOARD - HDMI IN ( No need any adjustment)

EDID data ( including HDCP ) is written in BCN

K BOARD - S- MASTER DIGITAL AUDIO AMPLIFIER (No need any adjustment )

S-Master NVM is written in BCN

BL (40-32") /BN (50W) /BP (42" PDP) / BL (26") BOARD (need adjustments)
AD ADJUSTMENT
Certain boards need to be adjusted Use TL Jig for the AD adjustment or follow the adjustment procedure described in SM
after replacement ( see table ) WHITE BALANCE ADJUSTMENT
Copy the WB data to new board using TL JIG or adjust the WB according to procedure described in SM

A1/A2/A3/A5 BOARD - FRONTEND BOARD (need adjustments)

When we replace A1/A2/A3/A5 , we need also to readjust Backend AD adjustments

G2 (V42) BOARD and G1,G2N (W50), (need adjustments)

G2(V26,32), G3L (40V/W) BOARD - PSU (No need any adjustment)

52
 SERVICE MODE AT2X Chassis
How to enter the service mode

(1-1) Switch the TV set to "Standby " condition

(1-2) Push "INFO" key on the remote commander
(1-3) Push "5" key on the remote commander
(1-4) Push "VOL +" key on the remote commander
(1-5) Push "POWER" key on the remote commander
(1-6) Push "MENU" key on the remote commander

Note: You have to perform the steps1 (1-2) to (1-5) within 3 seconds, otherwise the order will be cancelled.

The unit enter the service mode and yellow "S" character will be displayed

53
SERVICE MODE AT2X Chassis

The Service Menu can be used for:

1. Monitoring (version of the processors software, operating time…)

2. Adjustments ( AD converters, White Balance )
3. Tests ( Keys test, Aging Mode )

54
 JIGS & TOOLS AT2X Chassis
1. TL Jig

The TL JIG can be used for:

1.Read/Write of NVM data e.g. copy of the WB adjustment data after B board replacement.
2.Adjustment of AD converters after board replacements
3.Software update ( H8, PW )

Two types of TL Jigs are available: TL1 & TL3

The differences:
TL 1 is connected with PC using serial port and RS-232 cable
TL 3 is connected with PC using USB interface

More info about availability of the TL Jigs and the necessary software will be provided to the
authorized service stations via ASSIST (technical bulletins)

2. Extension cables

IF Board Part Number: 9-948-020-71 needed to connect A with B board

Two new cables are needed to connect the boards in the service position
Cable 1: Part Number: 9-948-020-73 G3/G3L board to NP1 board
Cable 2: Part Number: 9-948-020-72 N board CN3402 to A1/A2

55
 JIGS & TOOLS AT2X Chassis
AD Adjustments using TL Jig

1. Connect as follows

PC TL1/TL3 Board AT2X

Serial RS-232/USB
ESC
connector

LUMINANCE ADJUSTMENT
1. Input CVBS 100% White Raster
2. Go to CODE TOOL -> Command ( C ) -> Adjust ( Y )
3. Message "Adjusting...." appears on screen, colour tone changes
4. Wait until the message disappears
5. Repeat steps 1-4 for RGB 100% White Raster (Scart input)
6. Repeat steps 1-4 for YUV 100% White Raster (Component input)

CHROMINANCE ADJUSTMENT
1. Input CVBS 100% Blue Raster
2. Go to CODE TOOL -> Command ( C ) -> Adjust ( C )
3. Message "Adjusting...." appears on screen, colour tone changes
4. Wait until the message disappears
5. Repeat steps 1-4 for RGB 100% Blue Raster (Scart input)
6. Repeat steps 1-4 for YUV 100% Blue Raster (Component input)

56
 L/R
A1 board KD board speakers
RF board Audio delay
Not Mount!
CXD9826R K6X1008CZD AK4114 AK4384 NJM4558 TA2024
RF
Splitte Audio QSS/Audio
r Mono

Analog CVBS_TV
SPDIF out
MSP 4411G
FE HDMI_audio IC4102

Main LR TV LR

Variable Audio out

Variable Audio out NJM4558AV

SCL_D_5V/SDA_D_5V
IC4301

H8 board Headphone
AT2X Chassis
NJM3414AV
HP AMP
Smartlink
CVBS_Y
SAA5665HL
Con TEA6420
LVDS BLOCK DIAGRAM 26"
Sub uCOM
IC4302 TEXT_RGB+FB
Headphone H/V_SYNC
PAINTER2 LV
Y/C in IC4403 TS DS

(30Mbps)

CVBS in M27W201 SRAM

OTP 256K DTT
IC4410 IC4408
HDMI_audi

CSW_H/V N board
from CXA2181

Y1/C1
o

S2-1/S-1
V1 V6
L/R 1 L/R 6

CVBS1 in
TV V4 CVBS N BL board
RGB1+FB1 L/R 4 Audio N
TV out ITU656
VOUT3
AV1

YOUT1 CVBS/Y LVDS

COUT1 C YCbCr16bi
Mode 1 t D-Latch
S2-4
RGB _SW0
audio 1 in RGB_SW1
YUV_N
L/R TV CVBS/Y CCPX LVDS
audio_out(TV LPF PW166 CXD9756R
INI4 THC63L
) L/R OUT3 SM5302 SCALING BOLT
TEXT_RGB SW1 SW2 (90H)
Ys_C_SW Ys/C CXD3807 VDM84
AV SW CXA2069 IN4H C SN74LVC2G IC1810 IC2002
RGG1 / 2 SW
Y_N 53 IC1302 IC2004
IC5201 RGB1 4052 YUV SW DRC-MFV1rev RGB24bit
INI3 RGB24bit
RGB2 IC4804 CXA2181 Y/G CXD2097BQ
IN3H IC4807 AMP IC1702
CVBS2 in CVBS/Y for Sync
V2 CB/B LPF
(24H)
SM5302
RGB2+FB2 CompYUV (92H)
INI1 CR/R
Select videoout V/YOUT2 HDMI_YUV SELHOUT/VOUT 7W
AV2

H0

INI2 IIC 8

SDRAM
Mode 2 S2-2 16MB
IIC(5V) SCL_B_5V/
audio 2 Smartlink SDA_B_5V FLASH SDRAM
TEXT_FB ROM 16MB
in L/R 2
AV_FB
Select audio out FB1 FB SW LEVEL
L/R OUT2 SHIFT
FB2 4052
FB3 IC7509 Yout for
Sync

RGB_SW0 RGB_SW1
CSW_H/V
V3 SCL_D_5V/SDA_D_5V AV_FB_INV P-TXD/P-RXD

SCL_B/SDA_B YUV_N_SW Hitachi

VOUT1
RGB_SW0 MICRO IIC(3.3V)
RGB_SW1 HD65f2377
S2-3 SCL_B/SDA_B
IC1002
L/R 3
HDMI_SW
RTC
L/R OUT1 (64H)
YUV N SCL_B/SDA_B
L/R 5
Y V5
LEVEL
SHIFT
DVD audio

YUV

SCL_B_5V/SDA_B_5V

P board HDMI_YU
V
HDMI board DVD IN YUV
HDMI
 L/R
A board KD board speakers
RF board Audio delay

CXD9826R K6X1008CZD AK4114 AK4384 NJM4558 TA2024

RF
Splitte Audio QSS/Audio
r Mono

Analog CVBS_TV
SPDIF out
HDMI_audi MSP 4411G
FE o
Main LR TV LR

Variable Audio out

Variable Audio out NJM4558AV

SCL_D_5V/SDA_D_5V
H board Headphone
TEA6420
AT2X Chassis
NJM3414AV Smartlink Con LVDS
HP AMP CVBS_Y
TEXT_RGB+FB
SAA5665HL
Sub uCOM
BLOCK DIAGRAM
Headphone
Y/C in
H/V_SYNC PAINTER2
TS
(30Mbps)
LV
DS LCD TV 32 & 40
CVBS in M27W201 SRAM
OTP 256K DTT
HDMI_audi

CSW_H/V N board
from CXA2181

Y1/C1 TEXT_RG
o

S2-1/S-1 B
N/TEXT SW
V1 V6
TL52055
L/R 1 L/R 6
IC4801
N_
YUV N TEXT_
CVBS1 in
TV V4 CVBS N SW
B board
RGB1+FB1 L/R 4 Audio N
TV out ITU656
VOUT3
AV1

YOUT1 CVBS/Y LVDS

COUT1 C YCbCr16bi
Mode 1 t D-Latch
S2-4 RGB3_
TEXT_
audio 1 in SW
L/R TV CVBS/Y
RGB3/Text SW LPF LVDS
audio_out(TV CCPX
RGB3 TL52055 INI4 SM530 PW166 CXD9756R THC63
) L/R OUT3 RGB1_ IC4802 2 Ys_C_SW Ys/C SCALING BOLT LVDM8
RGB2_ IN4H C SN74LVC2G CXD3807
AV SW CXA2069 SW CVBS/Y (90H) 53 4
RGB1 RGG1 / 2 SW
for Sync RGB24bit RGB24bit
RGB2 TL52055 INI3 YUV SW 75ohm
Y/G
DRC-MFV1rev
driver CXD2097BQ
IC4803 IN3HCXA2181 MAX4451 x2
LPF
CVBS2 in CB/B (24H)
V2 SM530
CompYU
RGB2+FB2 2
V INI1 CR/R
HDMI_YU (92H)
Select videoout V/YOUT2 SELHOUT/VOUT 7W
AV2

H0

V INI2 IIC 8 SDRA

Mode 2 M
S2-2 IIC(5V) SCL_B_5V/ 16MB SDRA
audio 2 Smartlink SDA_B_5V FLASH
M
TEXT_FB ROM
in L/R 2 16MB
AV_FB
Select audio out FB1 LEVEL
L/R OUT2 FB SW
FB2 SHIFT
4052 Yout for
FB3
Sync

RGB_SW0 RGB_SW1 CSW_H/

CVBS3 in V3
SCL_D_5V/SDA_D_5V
V P-TXD/P-RXD
AV_FB_INV
RGB3+FB3 in SCL_B/SDA_B
Monitor
YUV_N_SW
AV3

V MUTE
out VOUT1 Hitachi
TC7S66F
RGB_SW0 IIC(3.3V)
Mode MICRO
RGB_SW1 HD65f2377 SCL_B/SDA_B
3 S2-3 RGB_SW2
audio 3
L/R 3 RGB_SW3
in
audio_out(Mo HDMI_SW
ni) RTC
L/R OUT1 (64H)
DVD audio SCL_B/SDA_B
L/R 5
Y V5
LEVEL
SHIFT
DVD audio YUV N

YUV

SCL_B_5V/SDA_B_5V

P board HDMI_YU
V
HDMI board DVD IN YUV
HDMI
 AT2X Wega Engine Analogue signal

Block diagram Digital signal

WEGA ENGINE Key Parts ・IP conversion

CXD2097BQ ・DRC
Analog Tuner Digital Tuner DRC-MFV1 ・Sharpness
CVBS
CVBS Y/Cb/Cr Y/Cb/Cr(8bit4:2:2)
CXA2069Q
Y/C AV SW PW166
External AV Input

・Scaling
Scaler
CVBS
（Only in case of
Text RGB Y/C HD signal input） RGB(8bit)
・Gamma
CXD9756R • Sharpness
Y/Cb/Cr BOLT for LCD ・W/B
SW
CXD9738R ・Over Drive(LCD only)
SCART RGB Thunder for PDP

NPD only
HDMI CXA2181AQ RGB 8bit CXD9842GG ・CALC
Comp SW Kirin false Contour Adapted
dynamic Level Control
Y/Cb/Cr RGB 8bit
G/B/R
LVDS
・PAL/NTSC/SECAM decode
CXD3807 ・3D Comb Filter
PDP/LCD Panel
・NR
CCPX ・Dynamic Picture
LCD - 26“,32”,40“ (16：9) S-LCD WXGA PVA

Y/Cb/Cr(8bit4:2:2) PDP - 42” (16 : 9) Samsung WVGA PVA

50” (16 : 9) NDP WXGA
 WEGA ENGINE FEATURES
1. CCPX 3D Combing: removes cross-color in static parts of
the image with no vertical resolution loss
2. CCPX image enhancements: intelligent black level control
(autopedestal) and ABL-dependent contrast (dc transfer)
3. DRC Sharpness enhancement : enhances detail of the
image without introducing preovershoots
4. DRC IP conversion: converts interlaced picture to
progressive picture with no vertical resolution loss in
static parts of the image
5. DCI: Dynamic Contrast Improvement: improves the
luminance detail in dark scenes
6. BOLT Kicker NR: reduces white noise from noisy sources
(i.e RF)
 PSU ( F, G1, G2 boards ) for KE-V42A10E/KDE-V42A12U

Circuit Description
1. Standby converter
This is a burst mode flyback type converter circuit, and consists of STR-A6169 which Control IC and power MOSFET were built in the same package.
Output voltage is 5.1V at point of C6207 and 18V are supplied as Vcc for control of a PFC converter.
Over Voltage Protection(OVP): If the No.2 pin of IC6101 becomes more than 28V, protection will operate and carries out the latch stop.
Over Current Protection(OCP): If the No.1 pin of IC6101 becomes more than 0.77V, protection of a pulse by pulse will operate.

2. PFC converter
This is a discontinuous current mode boost chopper converter controlled by UC3854N. And Q6306/Q6307Q6308 are MOSFET for the main switching.
Output voltage is about 385V and is adjusted by variable resistance RV6301.
AC input low voltage protection: If AC input is set to about 60v or less, operation will stop.
OVP: If output voltage exceeds 450V, it becomes a latch stop.
OCP: If the current of L6301 exceeds 17A, protection of a pulse by pulse will work.
Thermal shutdown: If the temperature of the heat sink with which Q6306,Q6307 and Q6308 is attached becomes about 120 degrees, it will latch stop.

3. VC converter
This is a half bridge current resonance type converter controlled by CXD9841P. And Q6501/Q6502 are MOSFET for the main switching.
Operation will be started if PFC output voltage exceeds 240V.
Output voltage are 33V for tuner, 18V for DC/DC converter, 10.5V for signal board, 24V for audio.
OVP: If 10.5V line voltage exceeds 16V or 18V line voltage exceeds 21V, protection will operate and carry out a latch stop.
OCP: If the current of C6517 exceeds about 2.2A, protection of a pulse by pulse will work.
If the state continues during a fixed period, it will become intermittent operation, and a latch stop will be carried out if it continues 4 times further.

4. VA converter
This is a half bridge current resonance type converter controlled by CXD9841P. And Q6703/Q6704 are MOSFET for the main switching.
This converter will start operation, if VC converter operates and primary Vcc voltage is supplied to IC6701.
Output voltage is variable from 50V to 70V, and it adjusted by variable resistance RV6601 so that the specification of a panel may be suited.
OVP: If output voltage exceeds 89V, protection will operate and carry out a latch stop.
OCP: If the current of C6715 exceeds about 3.5A, protection of a pulse by pulse will work.
If the state continues during a fixed period, it will become intermittent operation, and a latch stop will be carried out if it continues 4 times further.

5. VS converter
This is a half bridge current resonance type converter controlled by CXD9841P. And Q6905/Q6906 are MOSFET for the main switching.
This converter will start operation, if the No.9 pin of CN6403 (VS_ON terminal) becomes high.
Output voltage is variable from 195V to 215V, and it adjusted by variable resistance RV6801 so that the specification of a panel may be suited.
OVP: If output voltage exceeds 235V, protection will operate and carry out a latch stop.
OCP: If the current of C6915 exceeds about 4A, protection of a pulse by pulse will work.
If the state continues during a fixed period, it will become intermittent operation, and a latch stop will be carried out if it continues 4 times further.
 PSU ( F, G1, G2 boards ) for KE-V42A10E/KDE-V42A12U

Circuit Description

6. VE/VSET/VSCAN converter
All of these converters are the same circuit composition, and they are flyback type converters using the TOP-Switch.
TOP-Switch consists of one chip in a PWM control circuit and power MOSFET.
VE output voltage is variable from 70V to 110V,
and it adjusted by variable resistance RV6802 so that the specification of a panel may be suited.
VSET output voltage is variable from 180V to 210V,
and it adjusted by variable resistance RV6804 so that the specification of a panel may be suited.
VSCAN output voltage is variable from -170V to -190V,
and it adjusted by variable resistance RV6803 so that the specification of a panel may be suited.
OCP: This function is built in TOP-Switch, if the current of MOSFET exceeds 1.0A, it will operate, and if it continues during a fixed period,
it will become intermittent operation.
OVP: This function is realized by detecting the control winding voltage of a converter transformer. If winding voltage exceeds the zener voltage
for detection of each converter, a power supply will carry out a latch stop.

7. Sequence circuit
When Power signal is set to "H", a PFC converter operates, after the output rises, VC converter operates and VA converter operates.
When VS_ON(CN6108 #9) signal is set to “H”, VS converter operates, and VE/VSET/VSCAN converter operates.
Please refer to a Power ON sequence chart.
 PSU ( F, G1, G2 boards ) for KE-V42A10E/KDE-V42A12U

Block Diagram -1

AC DC

AC AC PFC 385V
VS Vs: 195V～215V

Filter Vcc Conv. Conv. D/D Conv.

Ve: 70V～110V

Vset: 180V～210V
D/D Conv.

AC D/D Conv.
Vscan: -170V～-190V

Filter G1 Board
STBY_5V VA Va: 50V～70V
STBY Conv.
Vg: 15V
Liner Reg.
D5VL: 5.2V
D/D Conv.
F Board D/D Conv.
D3V3: 3.3V

18V
33V
VC 10.5V
Conv. AU_24V
Vcc

Liner Reg. Vsb: 5V

G2 Board
 PSU ( F, G1, G2 boards ) for KE-V42A10E/KDE-V42A12U
Block Diagram -2
LATCH
LF6103 SBT
CIRCUIT POWER
D6101 Q6416/6418
R6103 T6102
D6202
VC TRANCE
St-by 5V
T6501
7 R6502 24V RECT
STBY 8 D6107 D6406
CONT
IC6101 VC Audio 24V
CONV
2 D6105 SW
Q6501 D6404/6405
Q6101 2 16 18V RECT
AC IN MAIN D6402 UNREG33V
RELAY
VC
127V～ RY6101
CONT
VC
CONV
1
F6101 15V
240V IC6501 SW
Q6502 LINER
10.5V RECT REG Vg 15V
8 12 D6403 IC 6402
CN6103
1 PS6401 D5VL
DC/DC
CONV D5VL 5.2V
IC6403
R6302 18V_RECT OVP
D6509 D6407 PS6402 D3V3
10.5V DC/DC
R6304 INRUSH PH6503 ERR_AMP D6409 D3V3 3.3V
CONV
RY6301 IC6401 D6407 IC6404
PH6502
R6701 REG 10.5V
VA TRANCE
T6701
5V
AC RECT LINER
D6309 2 REG
Vsb 5V
16 VA_RECT IC 6406
D6601
VA VA
CONV
CONT SW Va 50-70V
IC6701 Q6703

PFC PFC 8
PFC 1 12
CHOKE CHOKE
L6301 L6302 RECT VA Vs 195-215V
D6316 CONV
SW
Q6704 VE DC/DC CONV
VA
PH6701 ERR_AMP R6834 T6801
IC6601
D6811
VA_OVP Ve 70-110V
ＰＨ6702 IC6902
#13
PFC PFC PFC
SW SW Ve
Q6306 SW Q6308 THP6301 IC6802
Q6307 TOP223Y PH6801 ERR_AMP
VA_LVP
IC6902 IC6803
THERMAL #1

VSET DC/DC CONV

R6901
VS TRANCE T6803
L6902/T6901 R6848
D6825
16 Vset 180-210V
2 VS_RECT
16 VS D6801
VS CONV
15 PFC CONT SW IC6805 Ve
Q6905 PH6803 ERR_AMP
CONT IC6901 TOP223Y
IC6807
IC6301
8 11 8 12
1
VS
CONV
PFC_LVP SW VSCAN DC/DC CONV
IC6302 Q6906
#1
R6847 T6802
D6826
Vscan -170--190V
VE/VSET/
VS VS_OVP VSCAN
IC6902 OVP IC6804 Ve
PH6902 ERR_AMP PH6802 ERR_AMP
IC6801 #14 IC6902 TOP223Y
#2 IC6806

VS ON/OFF
PH6901 Q6801/6802
Q6803/6804 Vs_ON
Q6805/6806
PH6501
 PSU ( F, G1, G2 boards ) for KE-V42A10E/KDE-V42A12U
Power ON Sequence

AC IN

Standby Converter : ON PFC OUT > DC280V

STBY 5V Output
VA Converter : ON
Low
POWER
STANDBY Mode
CN6405 #3
VS_ON Low
High No Picture
CN6403 #9

PFC Converter : ON High

PFC OUT > DC240V PFC OUT >DC300V & Va >40V

VC Converter : ON
33V/24V/10.5V/VSb VS Converter : ON
Output

After about 5 seconds

VE Converter : ON
VSET Converter : ON
15V Output VSCAN Converter : ON
D3V3_D/D Conv. : ON
D5VL_D/D Conv. : ON

POWER ON Mode
 PSU ( F, G1, G2 boards ) for KE-V42A10E/KDE-V42A12U
Analysis flow chart for power supply problem-1

Power ON

POWER LED No F6101(F board) No LF6103(F board) No R6103(F board) No ST-BY 5V No Check other board
turn up ? open ? open ? open ? Normally H or B board
output ?

Yes Yes Yes Yes

Yes
VDR6101/VDR6102 short IC6101 OCP or OVP
Q6306/Q6307Q6308 D6101 broken IC6101 #1-#7 short Check ST-BY 5V line impedance
broken Check IC6101 #2 voltage: OVP>28V

POWER LED Yes CN6304 #4 Yes No Does voltage appear in Yes IC6501 OCP
red blink >370V? R6502 open? CN6401 #7 for a moment? Check VC converter putput
after 10 sec.? PFC out line impedance
VC OVP
No No Yes No Check IC6401or PH6503 etc.
VA OVP
Q6501/Q6502 IC6501 or Check IC6601or PH6701 etc.
PFC Converter failure broken around circuit
failure

VS OVP
Check IC6801 or PH6902 etc.
POWER LED Yes
red blink
after 20 sec.? VE OVP
Check IC6803 or PH6801 etc.
VSET OVP
No Check IC6807 or PH6803 etc.
VSCAN OVP
Check IC6806 or PH6802 etc.

Next sheet
 PSU ( F, G1, G2 boards ) for KE-V42A10E/KDE-V42A12U
Analysis flow chart for power supply problem-2

POWER LED Yes Yes Yes Yes Yes No 15V Yes

is Green No Vs voltage? No Va voltage? No D5VL voltage? No D3V3 voltage? voltage?
No picture
Abnormal
picture No No No No
VS converter VA converter IC6402 Panel
failure failure broken failure
No No
VE or VSET or VSCAN
converter
failure
C6407voltage is No C6407voltage is No VC converter
18V? 18V? failure

Yes
Yes
IC6403 IC6404
failure failure

VA converter
failure

No Does voltage appear in Yes IC6701 OCP

R6701 open? CN6407 #5 for a moment? Check VA output line impedance
(CN6407)
OVP
Yes No Check IC6601or PH6702 etc.

Q6703/Q6704 IC6701 or
broken around circuit
failure
 PSU ( F, G1, G2 boards ) for KE-V42A10E/KDE-V42A12U
Analysis flow chart for power supply problem-3

VS converter
failure

Is
No CN6403 #9 No Panel
R6901 open? (VS_ON) failure
Voltage
High ?
Yes Yes
Q6905/Q6906 Is
broken Q6801 emitter No Yes VC converter
Voltage PFC OUT>300V ? failure
10V ?

Yes No

PFC Converter failure

Does voltage appear in Yes IC6901 OCP

CN6409 #8 for a moment? Check VS output line impedance
(CN6408 or CN6409)
OVP
No Check IC6801 or PH6901 etc.

IC6901 or
around circuit
failure
 K Board
（S-Master Amp. Board）
 3-9. K Board System

Ｂｕｓ Ｃｏｎｔ
ｒｏｌ

PWM
③IC2604 ④IC2606
SPDIF IIS L
①IC2600 S-Master S-Master
Front_L
DIR Processor Amp.
（LC89056 （CXD9788R （CXD9774R
） ） ）

④IC2605
S-Master
IIS Amp. Front_R
PWM
R CXD9774R
③IC2607
②IC2603 IIS S-Master ④IC2608
CH Divider Processor S-Master
（CXD9835TN （CXD9788R PWM Amp. Woofer
） ） W CXD9774R

K ｂｏａｒｄ：3ch（L/R/W）
System
 3-9. K Board

IC2607
S-Master
Processor
（CXD9788
R）
IC2600
IC2606
DIR
S-Master
（LC89056）
Amp.
（CXD9774R）

IC2605
S-Master
Amp.
CXD9774R
IC2603
CH Divider
（CXD9835TN IC2608
） S-Master
IC2604
Amp.
S-Master
CXD9774R
Processor
（CXD9788
R）
 3-9. K Board Function

①DIR（LC89056）：IC2600
Functional Name：DIR（Digital Interface Receiver）
Power Supply：3.3V
Main function: Converts SPDIF signals into IIS format. No additional software is needed to control the IC.

②CH Divider（CXD9835TN）：IC2603
Functional Name：Channel Divider（CH_Divider）
Power Supply：3.3V
Main function： Establishes the digital filter and delay coefficient for the signal, and band passes the signal to the
front and the woofer channel.
Reads (initializes) the data from NVM when the power is turned on.
Once the power is on, reading of the data occurs simultaneously hen the S-master Mute occurs.)

③S-Master Processor（CXD9788R）：IC2604、IC2607
Functional Name：S-Master Processor
Power Supply：3.3V、1.8V
Main Function：Controls the S-master amplifier.
Converts the IIS signal into PWM format, and establishes gain control and sound format.
Equipped with the Mute port.
Controlled by DE microcontroller through three line serial.

④S-Master Amp.（CXD9774R）：IC2605、IC2606、IC2608
Functional Name：S-Master Amp.
Power Supply：3.3V、12V、25V
Main function：PWM digital amplifier. It amplifies PWM signal from the processor.
Equipped with error detection port.
 K Board（S-Master）
Block Diagram IC2602：REST IC(4.2V)
：R3112N421A
IC2614：
5.0V SN74LVC1G08DCKR
AMP_RST LC Filter
IC2609：SN74AHC2G14HDCU
M_RST

①IC2600
MCLK
SCLK
③IC2607 ④IC2608
LRCLK
SPDIF
SDATA

SDATA_W

②IC2603 ④IC2606
SN74LVC2G
SDATA_H
U04DCKR ③IC2604

IIC
④IC2605
IC2611： NVM:32k
SN74ALV4066A
CH_RST Mute Error
SCLATCH2

SCLATCH1
IC2601
SCDT
： DC_Detect
SCSHIFT SN74LV08APWR DC_Detect
Circuit
A_MUTE

SP_PROT
 3-9. Mute, Reset, Error Detection Summary

・MUTE Port on S-MasterProcessor

MUTE OFF：「H」 MUTE ON：「L」
→ It will Mute the IC (IC2604 & IC2607) itself.
（Conditions for Muting）
１．Through the A_MUTE line from DE microcontroller.
２．When the SPDIF error occurs or when there is no signal to the IC.
３．When the RESET IC (4.2V) is outputting “L”.

・RESET Ports：M_RST、CH_RST、AMP_RST
Reset OFF：「H」 Reset ON：「L」 (for all RESET Port)
（Summary for each Port）
１．M_RST
Reset port for the LC89056（IC2600) and CXD9788R（IC2604、IC2607)
※Certain amount of “delay” is made through IC2609
２．CH_RST
Reset port for the CXD9835TN（IC2603） and NV（32k）
３．AMP_RST
Reset port for the CXD9774R（IC2605、IC2606、IC2608）
※Reset will also occur when the RESET IC（4.2V） is outputting “L” or when there is no signal or PDIF error.

・SP_PROT Port error detection

Error not detected：「H」 Error detected：「Ｌ」
（Conditions for detecting the error)
１．When the DC output is detected at Speaker output ( for L＋/－、 R＋/－、 W ＋/－ ）
２．When the S-Master Amp.（CXD9774R）＜IC2605、IC2606、IC2608＞ detects OHP, OCP.
※The IC itself is equipped with Over Heat Protection and Over Current Protection.
 3-9. K Trouble Shooting -1
・Symptom 1 : No or irregular sounds from the L/R channel (but not from the Woofer Channel).
（To do）Check the input signals to and output signals from the IC2604.
（Your results）There are IIS input signals to the IC, but no PWM or irregular output signals from the IC.
（Cause）The IC2604 itself might have been sub-standard, or broken.
(Action) change K board.

・Symptom 2：No or irregular sounds from the Woofer channel (but not from the L/R channel)
（To do）Check the input signals to and output signals from the IC2607.
(Your results）There are IIS input signals to the IC, but no PWM or irregular output signals from the IC.
（Cause） The IC2607 itself might have been sub-standard, or broken.
(Action) change K board.

・Symptom 3：No sounds from either Lch, Rch, or Wch (Only one of three).
（To do）Check the IC2605（Lch）、ＩC2606（Rch） and IC2608（Wch）.
（Your results） There are IIS input signals to one of the each, but no PWM or irregular output signals from one
of the each.
（Cause） One of the IC2605（Lch）、ＩC2606（Rch） or IC2608（Wch) might have been sub-standard, or broken
(Action) change K board.
 3-9. K Trouble Shooting -2

・Symptom 4：No sounds from L, R, and Wch at all

（To do) Check the AMP_RST port of the IC2605（Lch）、ＩC2606（Rch） and IC2608（Wch）.
（Your results) The AMP_RST port is utputting “L”.
(Cause) Microcontroller port (AMP_RST) error or IC2602 and/or IC2614 might have been sub-standard or broken
(Action) change K board.

（To do） Check the M_RST port of the LC89056（IC2600） and CXD9788R（IC2604、IC2607）
（Your results） The M_RST port is outputting “L”
(Cause) Microcontroller port (M_RST) error or IC2609 might have been sub-standard or broken
(Action) change K board.

（To do) Check the input and output voltage of the IC6103<3.3V> and IC6101<12V>
（Your results） There are voltages supplied to the IC6103<3.3V> or IC6101<12V> but no output voltage from
either/both ICs
(Cause） Regulators (IC6103<3.3V> or IC6101<12V>）might have been sub-standard or broken.
(Action) change K board.

（To do） Check the input signals to or output signals from the CXD9835TN（IC2603）
（Your results） There are input IIS signals to the IC, but no output signals from the IC
(Cause) IC2603 might have been sub-standard or broken
(Action) change K board.

（To do） Check the input signals to or output signals from the LC89056（IC2600）
（Your results） There are input SPDIF signals to the IC, but no output signals from the IC
(Cause） IC2600 might have been sub-standard or broken.
(Action) change K board.
 3-9. K Trouble Shooting -3

・Symptom 5 ： Different sounds or irregular sound from L,R, or Wｃｈ

（Check） Check the input signals to or output signals from the CXD9835TN（IC2603）
（Result） There are input IIS signals present, but no or irregular output signals from the IC
（Cause） IC2603 might have been sub-standard or broken
(Action) change K board.

・Symptom ６：Interrupted or noisy sounds from the L, R, or/and Wｃｈ

（Check） Check the error port (JL 2616) of the LC89056（IC2600）
（Result） Outputting “H”
（Cause） SPDIF error .
SPDIF transmitter might have been sub-standard or broken or LC89056（IC2600） might have been sub-standard
or broken
(Action) change K board.