spare parts catalog Doc. no. R 223.

1335

SANDVIK CS430:01, 02
This document is valid for:

Serial no. / Machine no. Sign.

SANDVIK CS430:01, 02

© Copyright 2010 Sandvik SRP AB.

All rights reserved. No parts of this document may be reproduced or copied in any form or by
any means without written permission from Sandvik SRP AB. All data and information in this
manual may be changed without further notice. Reservations for misprints.

Document number: R 223.1335

Issue: 20110622
Version: 04

Sandvik
Stationsplan, SE-233 81 Svedala, Sweden
Tel: +46 (0)40 409000, Fax: +46 (0)40 409260
www.sandvik.com
SPC Sandvik CS430:01, 02 Table of Contents

1. Cone crusher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2. Wearing plates in bottom shell . . . . . . . . . . . . . . . . . . . . . . 11

3. Feed hopper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4. Rubber compression mountings . . . . . . . . . . . . . . . . . . 15

5. Hydroset-system (accumulator) . . . . . . . . . . . . . . . . . . . . . 17

6. Over pressure supply system . . . . . . . . . . . . . . . . . . . . . . 19

7a. Belt driving SPC, 4-pole 50 Hz . . . . . . . . . . . . . . . . . . . . . 21

7b. Belt driving SPC, 4-pole 60 Hz . . . . . . . . . . . . . . . . . . . . . 23

8. Belt driving 8V, 6-pole 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . 25

9. Sign assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

10. Service/Repair kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

© 2010 Sandvik SRP AB Doc. no. R 223.1335 Ver. 04 3

SPC Sandvik CS430:01, 02 Table of Contents

This page is intentionally left blank

4 Doc. no. R 223.1335 Ver. 04 © 2010 Sandvik SRP AB

SPC Sandvik CS430:01, 02 442.9931

1. Cone crusher

© 2010 Sandvik SRP AB Doc. no. R 223.1335 Ver. 04 5

SPC Sandvik CS430:01, 02 442.9931

Cat. No. Qty. Part number Alternative Description Remarks

1005-0 1 442.7908-00 Bottom Shell
1006-0 2 442.7201-00 Cover
1006-1 4 843.1267 Stud screw SMS1460 M12×45
1006-2 4 847.0147-00 Washer BRB 13×24 HB200 ISO 7089
1006-3 4 845.0030-00 Lock nut M12 8 FZB ISO 7040
1010-1 1 442.7915-01 Liner –-Pinionshaft arm
1010-2 2 442.7914-01 Liner – Narrow arm
1015-0 1 900.0027-00 Elbow A4/90 3" A4 SMS 435
1200-0 1 452.4190-001 Bottom Shell Bushing
1280-0 1 853.0464-00 Pin CP 12M6×12 SMS 2374

6 Doc. no. R 223.1335 Ver. 04 © 2010 Sandvik SRP AB

SPC Sandvik CS430:01, 02 442.9931

Cat. No. Qty. Part number Alternative Description Remarks

1005-0 1 442.7908-00 Bottom Shell
1285-0 1 900.0921-00 Swivel branch tee adapter 3/4"
1285-1 1 900.1412-00 Pipes Pipe KR 3/4"×70
1285-2 1 900.0276-00 Cover 3/4"
1320-0 1 442.8870-00 Liners bottom shell
1400-0 1 442.7929-01 Dust collar
1400-1 4 840.0634-00 Screw M6S 16×25 8.8 ISO 4017
1401-0 1 442.7932-01 Ring
1404-0 1 853.0464-00 Pin CP 12m6×12 SMS 2374
1405-0 12 840.1034-00 Screws M6S 16×60H 8.8
1405-2 12 847.0016-00 Washer BRB 17×30 HB200 ISO 7089
1410-0 1 452.4194-001 Locating Bar
1411-0 1 442.7933-01 Shim T=0.1
1 442.7933-02 Shim T=0.3
1 442.7933-03 Shim T=0.5
1 442.7933-04 Shim T=0.7
1412-0 3 841.0019-00 Screw MC6S 10×40 12.9
1430-0 1 442.7934-01 Gasket
1450-0 1 442.7931-01 Seal Ring – inner
1505-0 8 840.0070-00 Screw M6S 16×60 8.8 FZB ISO 4017
1505-2 8 847.0060-00 Washer TBRSB 17×42
1540-0 12 840.0720-00 Screws M6S 36×200 8.8
1540-1 12 845.0221-00 Nut M6M M36 8 FZB ISO 4032
1540-2 12 847.0162-00 Washer BRB 37×68 HB200 ISO 7089
1540-5 12 899.0229-00 Protective Cap SW55 2 H20
1550-0 4 442.9529-02 Screw M6S 36×90 8.8
1550-5 4 899.0229-00 Protective Cap SW55 2 H20
1805-0 1 442.8449-01 Eccentric
1810-0 1 452.4516-001 Eccentric bushing 16+20+25+30
1815-0 1 442.7926-01 Hub
1816-0 1 442.7930-01 Ring
1817-0 6 840.1156-00 Screws M6S 12×35 10.9
1817-2 6 847.0147-00 Washer BRB 13×24 HB200 ISO 7089
1820-0 1 442.9608-01 Key R 18×11×200
1825-0 5 841.0026-00 Screw MC6S 12×60 12.9
1825-1 7 841.0024-00 Screw MC6S 12×40 12.9
1825-2 12 847.0180-00 Washer DIN 137 B 13×24
1850-0 1 442.7802-00 Gear and pinion set
1855-0 1 442.8011-01 Key T 40×22×50
1880-0 1 452.4188-001 Ecc. Wearing plate
1885-0 8 853.0474-00 Spring pin prym N12×45
2005-0 1 442.7889-01 Hydroset cylinder
2020-0 12 840.0542-00 Screws M6S 24×75 8.8
2020-2 12 847.0124-00 Washer BRB 25×45 HB200 SS 3576
2050-0 1 442.7892-01 Hydroset cylinder bushing
2055-0 1 840.0019-00 Screws M6S 8×12 8.8
2055-2 1 847.0012-00 Washer BRB 8.4×16 HB200 ISO 7089
2140-0 1 873.0836-00 Seals O-ring 439.3×5.7
2205-0 1 442.9668-00 Piston
2225-0 1 853.0118-00 1_Pins CP m6 25×50
2260-0 1 442.7893-01 Piston wearing plate
2280-0 1 442.7894-01 Step washer
2305-0 1 442.7897-00 Chevron packing

© 2010 Sandvik SRP AB Doc. no. R 223.1335 Ver. 04 7

SPC Sandvik CS430:01, 02 442.9931

Cat. No. Qty. Part number Alternative Description Remarks

1005-0 1 442.7908-00 Bottom Shell
2400-0 1 442.7896-01 Packing clamp plate
2401-0 8 841.0266-00 Screw MC6S 12×25 8.8
2505-0 1 442.9667-00 Hydroset cylinder cover
2515-0 10 840.0670-00 Screw M6S 24×80 8.8 ISO 4017
2515-2 10 847.0124-00 Washer BRB 25×45 HB200 SS 3576
2530-0 1 902.0605-00 Air Bleeder valve
2540-0 1 873.0157-00 Seals O-ring 339.3×5.7 SMS 1586
2540-1 1 873.1275-00 Seals O-ring 370×5.7
2560-0 1 442.8783-01 Plug
2560-1 1 873.0111-00 O-ring 44.2×3 SMS 1586
2560-2 1 840.0023-00 Screws M6S 8×25 8.8
2560-3 6 847.0012-00 Washer BRB 8.4×16 HB200 ISO 7089
2560-4 4 840.0019-00 Screws M6S 8×12 8.8
3001-0 1 442.9962-00 Pinion shaft housing assembled
3005-0 1 442.7949-01 Pinion Shaft Housing
3030-0 1 442.7953-01 Gasket T= 0.5
1 442.7953-02 Gasket T= 0.8
1 442.7953-03 Gasket T= 1.5
3050-0 1 442.7802-02 Pinion
3070-1 1 868.0790-00 Bearing
3070-2 1 868.0805-00 Bearing
3090-1 1 442.7954-01 Spacer
3090-2 1 442.7954-01 Spacer
3120-1 1 873.0778-00 Seals O-ring 79.2×5.7 SMS 1586
3120-2 1 873.0778-00 Seals O-ring 79.2×5.7 SMS 1586
3170-1 1 873.1097-00 Oil seal ring 110×140×12
3170-2 1 873.1097-00 Oil seal ring 110×140×12
3190-1 1 442.7951-01 Bearing cover
3190-2 1 442.7950-01 Bearing cover
3210-0 6 840.0021-00 Screw M6S M8×20 8.8 fzb ISO 4017
3220-0 6 840.0046-00 Screw M6S 12×35 8.8 ISO 4017
3220-2 6 847.0147-00 Washer BRB 13×24 HB200 ISO 7089
3240-1 1 442.7957-01 Gasket
3240-2 1 442.7956-01 Gasket T= 0.5
1 442.7956-02 Gasket T= 0.8
3305-0 1 900.0717-00 Filter Plug G 1/4 F14
3330-0 1 853.0590-00 Spring Pin Prym N 8×28
3340-0 1 442.7959-01 Plug
3340-1 1 873.0383-00 Sealing Ring Tredo 16
3505-0 1 442.9936-01 Pinion shaft
3515-0 1 857.0046-00 Key R 16×10×80 SMS 2306
3575-0 1 442.2018-01 Plug
3575-2 1 900.0269-00 Barrel Nipples RSK 124 1645 DIN 20
3575-4 1 900.0275-00 Wrought iron pipe fittings Socket 3/4"
3585-0 1 442.7958-01 Nipple oil level
3585-1 1 873.0385-00 Tredo Nr.20 3/4"
3650-0 1 855.0103-00 3_Retaining Rings Retaining ring SgA 80
3710-0 2 840.1063-00 Screw M6S 16×120H 8.8
3710-1 2 845.0009-00 Nut M6M M16 8 FZB ISO 4032
4001-0 0 452.6149-901 Mainshaft assembly excl. mantle
4005-0 1 452.6117-901 Mainshaft with headcenter
4025-0 1 442.7913-01 Mainshaft sleeve

8 Doc. no. R 223.1335 Ver. 04 © 2010 Sandvik SRP AB

SPC Sandvik CS430:01, 02 442.9931

Cat. No. Qty. Part number Alternative Description Remarks

1005-0 1 442.7908-00 Bottom Shell
4035-0 1 853.0118-00 1_Pins CP m6 25×50
4075-0 1 442.7895-01 Mainshaft step
4135-0 1 855.0103-00 3_Retaining Rings Retaining ring SgA 80
4175-0 1 442.8471-01 Mantle B M1
1 442.8470-01 Mantle A M1
4175-9 20 831.0016-00 Casting compound (kg)
4205-0 1 442.7912-00 Head Nut with burn ring
4205-1 1 442.7918-01 Inner head nut
4205-2 1 442.7911-01 Burn ring
4305-0 1 442.8017-01 Dust seal ring
4350-0 1 442.8020-01 Retaining ring
4355-0 1 442.8021-01 Retainer
4355-1 1 442.8022-01 Scraper
4365-0 11 840.0068-00 Screw M6S 16×50 8.8 ISO 4017
4365-1 1 840.0070-00 Screw M6S 16×60 8.8 FZB ISO 4017
4365-2 12 847.0016-00 Washer BRB 17×30 HB200 ISO 7089
5001-0 0 452.6185-901 Topshell assembly excl. crushing chamber
5005-0 1 452.6109-001 Topshell
5110-0 6 442.9035-01 Liner
5112-0 16 452.6197-001 Dowel 2172-00 D 36×32
5150-0 2 452.6113-001 Arm shield
5155-0 2 452.6126-001 Dowel
5220-0 2 900.1262-00 Elbow Adapter G 1/4 B×R 1/4
5220-1 2 900.1030-00 Bushing RI-08-04 1/2"-1/4"
5240-0 2 452.6193-001 Hose SAE 100 R1AT R1/4"×550
5253-0 1 914.0093-00 Lubrication Nipple AH R 1/4"
5275-0 2 442.8506-01 Bracket
5285-0 4 840.0021-00 Screw M6S M8×20 8.8 fzb ISO 4017
5313-0 1 900.0243-00 Wrought iron pipe fittings Socket Rp 1/4
5313-1 2 900.2519-00 Adapter G 1/4 B×G 1/4 B
5650-0 1 442.8520-00 Spider cap
5650-1 1 912.0114-00 Air Filter P10102 R1/4"
5650-2 2 900.0134-00 Bushing 3/8"×1/4X"
5650-3 1 900.2008-00 2_Pipe couplings Elbow 45 SMS 453-10
5651-0 1 873.0833-00 Seals O-ring 379.3×5.7 SMS 1586
5655-0 4 840.0069-00 Screw M6S 16×55 8.8 ISO 4017
5655-2 4 847.0120-00 Washer TBRB 17×30
5675-0 1 442.6473-01 Spider bushing
5685-0 6 840.0080-00 Screw M6S 20×80 8.8 ISO 4014
5685-2 6 847.0132-00 Washer BRB 21×36 HB200 SS 3576
5705-0 1 442.6470-01 Oil seal ring
5750-0 1 900.0981-00 Plug BSPT 1" hexagon
6001-0 0 442.8510-00 Crushing chamber EC
6001-1 0 442.8511-00 Crushing chamber C
6001-2 0 452.1526-901 Crushing chamber MC
6305-0 1 442.8477-00 Lower concave ring EC
1 442.8478-00 Lower concave ring C
1 452.1464-901 Concave ring MC
6390-0 6 442.8484-00 Concave upper
6 442.8485-00 Concave upper C
6390-0 6 452.1465-901 Concave MC

© 2010 Sandvik SRP AB Doc. no. R 223.1335 Ver. 04 9

SPC Sandvik CS430:01, 02 442.9931

Cat. No. Qty. Part number Alternative Description Remarks

1005-0 1 442.7908-00 Bottom Shell
6390-9 60 831.0016-00 Casting compound (kg)
140 831.0016-00 Casting compound (kg)
200 831.0016-00 Casting compound (kg)
8401-0 1 442.8512-00 Hydroset
8950-0 1 442.8045-91 Wrench tool set
1 442.8045-90 Wrench tool set
1 442.8045-92 Wrench tool set

10 Doc. no. R 223.1335 Ver. 04 © 2010 Sandvik SRP AB

SPC Sandvik CS430:01, 02 442.8870

2. Wearing plates in bottom shell

1010-2
1320-4 1320-6

1320-1 1320-2
1320-5

1320-4
1320-6
1320-5
1320-2 1320-3 1010-1

Cat. No. Qty. Part number Alternative Description Remarks

1010-1 1 442.7915-01 Liner – Pinionshaft arm Arm liners
1010-2 2 442.7914-01 Liner – Narrow arm
442.8870-00 Wearing plates complete set
1320-1 2 442.8864-01 Wearing plates Included in wearing plates complete set
1320-2 2 442.8865-01 Wearing plates
1320-3 1 442.8866-01 Wearing plates
1320-4 2 442.8867-01 Wearing plates
1320-5 2 442.8868-01 Wearing plates
1320-6 2 442.8869-01 Wearing plates
9 442.8799-06 Bar 1312-00 4-kt 12×60
6 847.0059-00 Washer TBRSB 13.5×36 1370
2 840.0048-00 Screw M6S 12×45 8.8 ISO 4017

© 2010 Sandvik SRP AB Doc. no. R 223.1335 Ver. 04 11

SPC Sandvik CS430:01, 02 442.8870

This page is intentionally left blank

12 Doc. no. R 223.1335 Ver. 04 © 2010 Sandvik SRP AB

SPC Sandvik CS430:01, 02 442.8529

3. Feed hopper

2, 3, 4

Pos. No. Qty. Part number Alternative Description Remarks

442.8529-00 Feed hopper
1 1 442.8517-00 Feed hopper
2 12 840.0080-00 Screw M6S 20×80 8.8 ISO 4014
3 12 845.0010-00 Nut M6M M20 8 ISO 4032
4 12 847.0132-00 Washer BRB 21×36 HB 200

© 2010 Sandvik SRP AB Doc. no. R 223.1335 Ver. 04 13

SPC Sandvik CS430:01, 02 442.8529

This page is intentionally left blank

14 Doc. no. R 223.1335 Ver. 04 © 2010 Sandvik SRP AB

SPC Sandvik CS430:01, 02 442.9776

4. Rubber compression mountings

1, 2

3
4
5, 6
6, 7

6, 8, 9
4
5, 6
7

Pos. No. Qty. Part number Alternative Description Remarks

442.97766-00 Rubber compression mountings for crusher
01 1 845.0387-00 Nut M24 8 ISO 7040
02 1 847.0124-00 Washer BRB 25×45 HB 200
03 1 442.9779-00 Top plate
04 1 864.0080-00 Rubber compression mounting
05 8 840.0044-00 Screw M6S 12×25 8.8 ISO 4017
06 8 847.0147-00 Washer BRB 13×24 HB 200 ISO 7089
07 1 442.9780-01 Lower fixing plate

Pos. No. Qty. Part number Alternative Description Remarks

442.97766-90 Rubber compression mountings for crusher on subframe
04 1 864.0080-00 Rubber compression mounting
05 4 840.0044-00 Screw M6S 12×25 8.8 ISO 4017
06 12 847.0147-00 Washer BRB 13×24 HB 200 ISO 7089
07 1 442.9780-01 Lower fixing plate
08 4 840.0048-00 Screws M6S 12×45 8.8 ISO 1417
09 4 845.0030-00 Lock nut M12 FZB ISO 7040

© 2010 Sandvik SRP AB Doc. no. R 223.1335 Ver. 04 15

SPC Sandvik CS430:01, 02 442.9776

This page is intentionally left blank

16 Doc. no. R 223.1335 Ver. 04 © 2010 Sandvik SRP AB

SPC Sandvik CS430:01, 02 442.8512

5. Hydroset-system (accumulator)

Pos. No. Qty. Part number Alternative Description Remarks

01 1 902.0605-00 Air bleeder UV 121
03 1 900.0810-00 Reducer RED R3/4×R1/2
04 2 873.0385-00 Sealing ring TREDO 20
05 1 900.0655-00 Adapter R3/4"
06 1 650.0154-01 Hose 3/4 L=900
07 1 442.5969-01 Connection
08 1 900.0746-00 Tube clamp RSGU 11 1100 30/15
09 1 840.0013-00 Screw M6S 6×25
10 1 845.0004-00 Nut M6M5
11 1 442.2100-01 Bracket 1312-00
12 1 442.8694-00 Protection
13 1 900.0648-00 Adapter 1"×2/4"
14 1 873.0386-00 Sealing ring TREDO 23
15 1 442.6908-01 Bushing 1914-04
16 1 873.0390-00 Sealing ring TREDO 30
17 1 919.0070-00 Protection plug R3/4
1 919.0231-00 Adapter ISO228-G2A - ISO228-G2A Between check valve and accumualator

© 2010 Sandvik SRP AB Doc. no. R 223.1335 Ver. 04 17

SPC Sandvik CS430:01, 02 442.8512

This page is intentionally left blank

18 Doc. no. R 223.1335 Ver. 04 © 2010 Sandvik SRP AB

SPC Sandvik CS430:01, 02 442.8642

6. Over pressure supply system

CRUSHER

30 31 32 33 34 36 35 13

37

39

7
35
442.8642-90
442.8642-00

14
20 21 22 23 24 13 2

3
4 3 2 15
4

3
14
2

13 6 2 3

442.8642-00

12

TANK

Pos. No. Qty. Part number Alternative Description Remarks

442.8642-00 Over pressure unit Complete
442.8642-90 Over pressure unit for compressed air Complete
02 4 900.1424-00 Hose coupling 3/4
03 4 900.1358-00 Clips 28 SMS 2298 Dy 23-27mm
04 5 819.0187-00 Hose 1
06 1 900.0040-00 Tee ISO49 B1 3/4
12 4 900.0365-00 -00 Hexagon nipple R 3/4
13 4 900.0022-00 -00 Elbow 3/4 A4 SMS 435
14 5 900.1139-00 -00 Clip RSGU 1.22/15
15 1 900.0005-00 -00 Elbow ISO49 A1 3/4"
20 1 442.9325-00 -00 Over pressure fan
22 2 912.0138-00 -00 Air filter Purolator PI 0154
24 2 900.0108-00 -00 Wrought iron pipe fittings 1×3/4
07 1 900.0209-00 -90 Plug R 3/8 ISO 49 T8 FZV
13 2 900.0022-00 -90 Elbow 3/4 A4 SMS 435
14 2 900.1139-00 -90 Clip RSGU 1.22/15
15 1 900.0005-00 -90 Elbow ISO49 A1 3/4
30 1 900.0180-00 -90 Nipple ISO49 N8 1/2×1/4
31 1 912.0113-00 -90 Air filter 504-2S 5 Micron
32 1 900.0169-00 -90 Nipple 1/4 ISO49 N8
33 1 902.0645-00 -90 Regulator 216-2-8
34 1 900.0182-00 -90 Nipple ISO49 N8 3/4×1/4
35 2 900.0054-00 -90 Tee ISO49 B1 3/4×3/8
36 1 900.0209-00 -90 Plug R 3/8 ISO 49 T8 FZV
37 1 923.0267-00 -90 Pressure gauge 2060 D100 0-1000 PA
39 1 900.0172-00 -90 Nipple ISO49 N8 3/4

© 2010 Sandvik SRP AB Doc. no. R 223.1335 Ver. 04 19

SPC Sandvik CS430:01, 02 442.8642

This page is intentionally left blank

20 Doc. no. R 223.1335 Ver. 04 © 2010 Sandvik SRP AB

SPC Sandvik CS430:01, 02 442.9939

7a. Belt driving SPC, 4-pole 50 Hz

9 10
B

B B-B

A
11

4 2 1

5
6
7, 8
3

A-A
Pos. No. Qty. Part number Alternative Description Remarks
01 1 879.0437-00 V-belt Pulley 375 MGT 100 6×SPC
02 1 869.0189-00 Bushing MGT No. 100 Di = 80
03 - - Screw MC6S 16×60 Included in bushing
04 1 857.0346-00 Key R 22×14×80 SMS 2306
05 1 442.9940-01 Spacer D95/80×24
06 1 442.7955-01 Washer 2142-50 D95/17×10
07 1 847.0016-00 Washer BRB 17×30 HB200 ISO 7089
08 1 840.0066-00 Screw M6S M16×40 8.8 fzb ISO 4017
09 1 879.0261-00 V-belt Pulley 355 MGT 100 6×SPC
869.0221-00 Di = 65
869.0187-00 Di = 75
10 1 MGT No. 100 According to order
869.0188-00 Di = 85
869.0258-00 Di = 90
11 1 875.0323-00 2360, standard V-belt SPC Other dimensions according to order
C-C 607

© 2010 Sandvik SRP AB Doc. no. R 223.1335 Ver. 04 21

SPC Sandvik CS430:01, 02 442.9939

This page is intentionally left blank

22 Doc. no. R 223.1335 Ver. 04 © 2010 Sandvik SRP AB

SPC Sandvik CS430:01, 02 452.3354

7b. Belt driving SPC, 4-pole 60 Hz

10

9 3 2

18

6, 7
5
4

Pos. No. Qty. Part number Alternative Description Remarks

01 1 875.0244-00 2500, standard V-belt SPC
C-C 607
869.0221-00 Di = 65
869.0187-00 Di = 75
02 1 Bushing MGT No. 100
869.0188-00 Di = 85
869.0258-00 Di = 90
03 1 879.0495-00 V-belt pulley 450 MGT 100 6×SPC
04 1 442.9940-01 Spacer D95/80×24
05 1 442.7955-01 Washer 2142-50 D95/17×10
06 1 840.0066-00 Screw M6S M16×40 8.8 fzb ISO 4017
07 1 847.0016-00 Washer BRB 17×30 HB200 ISO 7089
08 1 857.0346-00 Key R 22×14×80 SMS 2306
09 1 869.0189-00 Bushing MGT No. 100 Di = 80
10 1 879.0437-00 V-belt pulley 375 MGT 100 6×SPC

© 2010 Sandvik SRP AB Doc. no. R 223.1335 Ver. 04 23

SPC Sandvik CS430:01, 02 452.3354

This page is intentionally left blank

24 Doc. no. R 223.1335 Ver. 04 © 2010 Sandvik SRP AB

SPC Sandvik CS430:01, 02 442.9878

8. Belt driving 8V, 6-pole 60 Hz

7
B 6

B-B
B

A
8
5 1
9

2
4

A-A

Pos. No. Qty. Part number Alternative Description Remarks

01 1 869.0327-00 Bushing QD J80mm Di=80
02 1 442.7955-01 Washer 2142-50 D95/17×10
03 1 847.0016-00 Washer BRB 17×30 HB200 ISO 7089
04 1 840.0066-00 Screw M6S M16×40 8.8 fzb ISO 4017
05 1 879.0615-00 V-belt Pulley QD Dy 17" 6×8V
869.0338-00 M3-38 Di = 3⅜
06 1 869.0339-00 M3-58 Di = 3⅝ Bushing QD M3 According to order
869.0333-00 M3-78 Di = 3⅞
07 1 879.0623-00 V-belt Pulley QD Dy 20" 6×8V
08 1 875.0364-00 1400, standard V-belt 8V Other dimensions according to order
C-C 1047
09 1 857.0209-00 Key R 22×14×100 SMS 2306

© 2010 Sandvik SRP AB Doc. no. R 223.1335 Ver. 04 25

SPC Sandvik CS430:01, 02 442.9878

This page is intentionally left blank

26 Doc. no. R 223.1335 Ver. 04 © 2010 Sandvik SRP AB

SPC Sandvik CS430:01, 02 452.4922

9. Sign assembly
5 5

2 1 1
2

4 4
4 4

120
5

3 5

6 3, 5
7
8

88

Pos. No. Qty. Part number Alternative Description Remarks

1 2 126.0422-001 Sign product name
2 2 126.0443-001 SANDVIK logotype silver 100
3 1 126.0383-001 Risk of crushing
4 4 885.0249-00 Signs centre of gravity
5 4 126.0384-001 Warning flying fragments
6 1 126.0385-001 Warning sign read manual
7 1 126.5007-01 Identification plate
8 1 885.0267-00 Warning sign Danger

© 2010 Sandvik SRP AB Doc. no. R 223.1335 Ver. 04 27

SPC Sandvik CS430:01, 02 452.4922

This page is intentionally left blank

28 Doc. no. R 223.1335 Ver. 04 © 2010 Sandvik SRP AB

SPC Sandvik CS430:01, 02

10. Service/Repair kit

Locating bar kit 452.5797-901

Cat. No. Qty. Part number Alternative Description Remarks
1410-0 1 442.7928-01 Locating bar
1411-0 1 442.7933-01 Shim t=0.1
1 442.7933-02 Shim t=0.3
1 442.7933-03 Shim t=0.5
1 442.7933-04 Shim t=0.7
1412-0 3 841.0019-00 Screw MC6S 10×40 12.9

Pinionshaft housing repair kit 452.5574-901

Cat. No. Qty. Part number Alternative Description Remarks
3030-0 1 442.7953-01 Gasket T= 0.5
1 442.7953-02 Gasket T= 0.8
1 442.7953-03 Gasket T= 1.5
3070-1 1 868.0790-00 Bearing
3070-2 1 868.0805-00 Bearing
3090-1, -2 2 442.7954-01 Spacer
3120-1, -2 2 873.0778-00 O-ring
3170-1, -2 2 873.1097-00 Seal
3240-1 1 442.7957-01 Gasket
3240-2 1 442.7956-01 Gasket T=0.5
3240-2 1 442.7956-02 Gasket T=0.8
3340-1 1 873.0383-00 Sealing Ring Tredo 16
3585-1 1 873.0385-00 Sealing Ring Tredo Nr.20 3/4"

Bottomshell arm liner kit 452.5777-901

Cat. No. Qty. Part number Alternative Description Remarks
1010-1 1 442.7915-01 Pin shaft arm liner
1010-2 2 442.7914-01 Narrow arm liner

(Continued)

© 2010 Sandvik SRP AB Doc. no. R 223.1335 Ver. 04 29

SPC Sandvik CS430:01, 02

Bottomshell liner kit v

Cat. No. Qty. Part number Alternative Description Remarks
1320-1 2 442.8864-01 Wearing plates
1320-2 2 442.8865-01 Wearing plates
1320-3 1 442.8866-01 Wearing plates
1320-4 2 442.8867-01 Wearing plates
1320-5 2 442.8868-01 Wearing plates
1320-6 2 442.8869-01 Wearing plates
9 442.8799-06 Bar 1312-00 4-kt 12×60
6 847.0059-00 Washer TBRSB 13.5×36 1370
2 840.0048-00 Screw M6S 12×45 8.8 ISO 4017

Filter kit 452.5542-901

Pos. No. Qty. Part number Alternative Description Remarks
1 912.0126-00 Filter HC69
1 912.0129-00 Filter cartridge HC2

1 912.0139-00 Filter cartridge HC2 852516 MIC

1 912.0155-00 Filter cartridge HC2 852514 MIC

30 Doc. no. R 223.1335 Ver. 04 © 2010 Sandvik SRP AB