CAMPUS® Datasheet

Zytel® FG101L NC010 - PA66

DuPont Engineering Polymers

Product Texts
Zytel® FG101L NC010 is a lubricated polyamide 66 resin for injection molding. It has been developed for consideration into applications
such as parts for the food industry.
FOOD CONTACT
This product is manufactured according to Good Manufacturing Practice (GMP) principles and generally accepted in food contact
applications in Europe and the USA when meeting applicable use conditions. For details, individual compliance statements are available
from your DuPont representative.

Rheological properties dry / cond Unit Test Standard

Molding shrinkage, parallel 1.4 / * % ISO 294-4, 2577
Molding shrinkage, normal 1.4 / * % ISO 294-4, 2577

Mechanical properties dry / cond Unit Test Standard

Tensile modulus 3100 / 1400 MPa ISO 527-1/-2
Yield stress 82 / 55 MPa ISO 527-1/-2
Yield strain 4.5 / 25 % ISO 527-1/-2
Nominal strain at break 25 / >50 % ISO 527-1/-2
Tensile creep modulus, 1h * / 1400 MPa ISO 899-1
Tensile creep modulus, 1000h * / 820 MPa ISO 899-1
Charpy impact strength, +23°C N/N kJ/m² ISO 179/1eU
Charpy impact strength, -30°C 400 / N kJ/m² ISO 179/1eU
Charpy notched impact strength, +23°C 5.5 / 15 kJ/m² ISO 179/1eA
Charpy notched impact strength, -30°C 4.5 / 3 kJ/m² ISO 179/1eA

Thermal properties dry / cond Unit Test Standard

Melting temperature, 10°C/min 262 / * °C ISO 11357-1/-3
Glass transition temperature, 10°C/min 70 / * °C ISO 11357-1/-2
Temp. of deflection under load, 1.80 MPa 70 / * °C ISO 75-1/-2
Temp. of deflection under load, 0.45 MPa 190 / * °C ISO 75-1/-2
Vicat softening temperature, 50°C/h 50N 240 / * °C ISO 306
Coeff. of linear therm. expansion, parallel 100 / * E-6/K ISO 11359-1/-2
Coeff. of linear therm. expansion, normal 110 / * E-6/K ISO 11359-1/-2
Burning behavior at 1.5 mm nominal thickness V-2 / * class IEC 60695-11-10
Thickness tested (1.5) 1.5 / * mm IEC 60695-11-10
Yellow Card available Yes / * - -
Burning behavior at thickness h V-2 / * class IEC 60695-11-10
Thickness tested (h) 0.7 / * mm IEC 60695-11-10
Yellow Card available Yes / * - -
FMVSS DNI - ISO 3795 (FMVSS 302)
Oxygen index 28 / * % ISO 4589-1/-2

Electrical properties dry / cond Unit Test Standard

Relative permittivity, 100Hz 3.8 / 6 - IEC 62631-2-1
Relative permittivity, 1MHz 3.5 / 4 - IEC 62631-2-1
Dissipation factor, 100Hz 80 / 2100 E-4 IEC 62631-2-1
Dissipation factor, 1MHz 180 / 750 E-4 IEC 62631-2-1
Volume resistivity 1E12 / 1E10 Ohm*m IEC 62631-3-1
Surface resistivity * / 1E12 Ohm IEC 62631-3-2

Last update: 2022-09-01 Source: https://www.campusplastics.com Page: 1/4

Zytel® FG101L NC010 - PA66
DuPont Engineering Polymers

Electric strength 32 / 28 kV/mm IEC 60243-1

Comparative tracking index 600 / - - IEC 60112

Other properties dry / cond Unit Test Standard

Water absorption 8.5 / * % Sim. to ISO 62
Humidity absorption 2.6 / * % Sim. to ISO 62
Density 1140 / - kg/m³ ISO 1183

Material specific properties dry / cond Unit Test Standard

Viscosity number 150 / * cm³/g ISO 307, 1157, 1628

Film Properties dry / cond Unit Test Standard

Strain at yield, parallel 4.5 / * % ISO 527-3

Rheological calculation properties Value Unit Test Standard

Density of melt 970 kg/m³ -
Thermal conductivity of melt 0.16 W/(m K) -
Spec. heat capacity melt 2790 J/(kg K) -
Eff. thermal diffusivity 5E-8 m²/s -
Ejection temperature 190 °C -

Characteristics

Processing Additives
Injection Molding Release agent

Delivery form Regional Availability

Pellets North America, Europe, Asia Pacific, South and Central America

Other text information

Injection molding

POSTPROCESSING

Annealing: 30min at 200°C

Chemical Media Resistance

Acids
Acetic Acid (5% by mass) (23°C)
Citric Acid solution (10% by mass) (23°C)
Lactic Acid (10% by mass) (23°C)
Hydrochloric Acid (36% by mass) (23°C)
Nitric Acid (40% by mass) (23°C)
Sulfuric Acid (38% by mass) (23°C)
Sulfuric Acid (5% by mass) (23°C)
Chromic Acid solution (40% by mass) (23°C)

Bases
Sodium Hydroxide solution (35% by mass) (23°C)
Sodium Hydroxide solution (1% by mass) (23°C)
Ammonium Hydroxide solution (10% by mass) (23°C)

Last update: 2022-09-01 Source: https://www.campusplastics.com Page: 2/4

Zytel® FG101L NC010 - PA66
DuPont Engineering Polymers

Alcohols
Isopropyl alcohol (23°C)
Methanol (23°C)
Ethanol (23°C)

Hydrocarbons
n-Hexane (23°C)
Toluene (23°C)
iso-Octane (23°C)

Ketones
Acetone (23°C)

Ethers
Diethyl ether (23°C)

Mineral oils
SAE 10W40 multigrade motor oil (23°C)
SAE 10W40 multigrade motor oil (130°C)
SAE 80/90 hypoid-gear oil (130°C)
Insulating Oil (23°C)

Standard Fuels
ISO 1817 Liquid 1 (60°C)
ISO 1817 Liquid 2 (60°C)
ISO 1817 Liquid 3 (60°C)
ISO 1817 Liquid 4 (60°C)
Standard fuel without alcohol (pref. ISO 1817 Liquid C) (23°C)
Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23°C)
Diesel fuel (pref. ISO 1817 Liquid F) (23°C)
Diesel fuel (pref. ISO 1817 Liquid F) (90°C)
Diesel fuel (pref. ISO 1817 Liquid F) (>90°C)

Salt solutions
Sodium Chloride solution (10% by mass) (23°C)
Sodium Hypochlorite solution (10% by mass) (23°C)
Sodium Carbonate solution (20% by mass) (23°C)
Sodium Carbonate solution (2% by mass) (23°C)
Zinc Chloride solution (50% by mass) (23°C)

Other
Ethyl Acetate (23°C)
Hydrogen peroxide (23°C)
DOT No. 4 Brake fluid (130°C)
Ethylene Glycol (50% by mass) in water (108°C)
1% nonylphenoxy-polyethyleneoxy ethanol in water (23°C)
50% Oleic acid + 50% Olive Oil (23°C)
Water (23°C)
Deionized water (90°C)
Phenol solution (5% by mass) (23°C)

Last update: 2022-09-01 Source: https://www.campusplastics.com Page: 3/4

Zytel® FG101L NC010 - PA66
DuPont Engineering Polymers

All data provided according to ISO 10350 for single points and ISO 11403 for multipoints.

Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying,
etc.
Test temperatures are 23°C unless otherwise stated.

DuPont™, the DuPont Oval Logo, and all products, unless otherwise noted, denoted with ™, ℠ or ® are trademarks, service marks or
registered trademarks of affiliates of DuPont de Nemours, Inc. © 2021 DuPont de Nemours, Inc. All rights reserved.

The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication.
This information may be subject to revision as new knowledge and experience becomes available.
The information set forth herein is furnished free of charge and is based on technical data that DuPont believes to be reliable and falls
within the normal range of properties. It is intended for use by persons having technical skill, at their own discretion and risk. This data
should not be used to establish specification limits nor used alone as the basis of design. Handling precaution information is given with the
understanding that those using it will satisfy themselves that their particular conditions of use present no health or safety hazards. Since
conditions of product use and disposal are outside our control, we make no warranties, express or implied, and assume no liability in
connection with any use of this information. As with any product, evaluation under end-use conditions prior to specification is essential.
Nothing herein is to be taken as a license to operate or a recommendation to infringe on patents.
DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products.

CAUTION: DO NOT USE DUPONT MATERIALS IN MEDICAL APPLICATIONS INVOLVING IMPLANTATION IN THE HUMAN BODY OR
CONTACT WITH INTERNAL BODY FLUIDS OR TISSUES UNLESS THE MATERIAL HAS BEEN PROVIDED FROM DUPONT UNDER A
WRITTEN CONTRACT THAT IS CONSISTENT WITH DUPONT POLICY REGARDING MEDICAL APPLICATIONS AND EXPRESSLY
ACKNOWLEDGES THE CONTEMPLATED USE.

For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical
Applications... H-50103-5 and DuPont CAUTION Regarding Medical Applications... H-50102-5.

Last update: 2022-09-01 Source: https://www.campusplastics.com Page: 4/4