iX3

Here's how you can contact us

www.iscooterglobal.com
www.facebook.com/iScooterGlobal
[email protected]
 QUICK START

1. Push down (black locking lever) so that 2. Cut the tapes on the handlebar.Lift the
you can unfold the stem upright. handlebars on both sides up and slide
Hold the stem, close up (red lever), and in to secure.
press down to lock it while pulling (ring
locking pin).

TIPS

MiniRobot

A B
If there is some noise from the rear brake Download the "MiniRobot" app
disc or the rear suspension. (Image A) from the App Store(iPhone) or
PLEASE EMAIL US FOR ASSIS- Google Play (Android phone) for
TANCE.:[email protected] more information and functions.
 EN

Contents
Product Safety Notice 01
What's included 02
Product Overview 03
Specification 04
Display Content 05
Screen 08
E-SCOOTER APP 09
Assemble 10
Attention 10
Riding Basics 11
Riding Notice 12
Dangerous Actions 13
Charging 14
Disc Brake Adjustment 15
Daily Care and Maintenance 16
Limited Warranty Statement 17
Error Code 18
FAQ 19
Contact Us 19
 Product
Product Safety
Safety Notice
Notice

Don't Ride Until You Read This:

Always wear a helmet, elbow pads, and knee pads when riding your electric scooter.

Make sure your electric scooter has a full charge, and all screws are closely tightened
before riding.

Always be aware of local road laws, and follow them.

Do not ride under the influence of drugs or alcohol.

Always respect pedestrians.

Do not ride under heavy rain or extreme temperature conditions. Do not ride in a puddle
deeper than 1.5 inches. The electric scooter may slide causing injury.
These conditions may damage the electronics and void the warranty.

Warning Message
Avoid Water --- The electric scooter has an IPX4 rating. The electronics may be damaged due to water and
water damage is not covered by our warranty. Riding in heavy rain or extreme temperature conditions is
also very dangerous and may result in injury.
Keep Away from Fire --- Do not bring the electric scooter near the fire.
Proper Storage --- Avoid prolonged exposure to sun or rain and avoid storage in places with high
temperatures or corrosive gas.
Abuse --- We do not cover physical damage due to negligent care and extreme riding.
Safety Ride --- Whenever you ride the iscooter electric scooter, you risk severe injury or even death from
loss of control, collisions, and falls.
Be Careful --- Use caution and ride at your own risk.
No Modification --- Only use original brand accessories. Unauthorized modification is strictly prohibited.
Before Riding --- Be sure to check that the entire scooter is in good condition, such as whether the
locking screws of the motor, front wheels, folding joints, etc. are fastened and reliable. Do not ride at will
before correcting any problems.
Before Riding --- be sure to check that the braking system is functioning properly, also be sure to check
that all safety labels are in place and you understand the safety warnings.
No Hanging --- Do not hang heavy objects on the handlebars.
No Use --- Pregnant women, the disabled, and those with heart problems should not use this product.
Save Electricity --- To conserve electricity, do not brake frequently, ride against the wind, or carry heavy
loads including other people.
Age Limit --- The electric scooter should never be used by children under the age of 16.
Not Overload --- Never exceed the 120 kg (264lbs) maximum load rating.
Moving Parts Hazard --- Keep hands and all body parts away from moving parts while operating the electric
scooter.
Caution --- Make note that additional insurance may be required to cover situations you encounter while
riding an electric scooter. It is recommended that you contact an insurance company or broker for advice
and consultation.
01
 What's included

Carefully check what's included in the package box, if anything is missing or damaged,
please contact iscooter customer service for support: [email protected]

Keep the package box to ship back the scooter if necessary.

1 x iscooter

1 x Charger 1 x Tool Kit 1 x Allen Wrench

02
 Product Overview

Display
Control Panel

Brake Lever

Folding key

Deck

Brake LED

Headlight

Motor wheel

Kickstand

Battery compartment

Indicators / Led lights

03
 Specification

Project Content Parameters

Unfolded Dimensions 47*23*50 IN / 120*60*128CM

Folded Dimensions 47*8*19 IN / 120*20*50 CM

Net Weight 48.5 LBS /22 KG

Top Speed 25 MPH/ 40 KM/H

Max. Range 18-25 Miles/30-40KM

Scooter Parameters
Hill Climbing 20% - 25% Grade

Terrain All-Terrain Wheels

Operating Temperature 14 °F - 104 °F

Storage Temperature -4 °F - 104 °F

Waterproof Rating IPX4

Charging Time 6-7H

Rated Voltage 48V

Battery Parameters
Capacity 10 Ah

Wheel Size 10 Inches

Tire Type Off Road Tubeless Tire

Motor Parameters Rated Voltage 48 V

Power 800 W

Motor Type Brushless DC Motor

Front and rear mechanical disc

Brake Brakes brake + electric brake

Input Voltage 100 V ~ 240 V

Charger Output Voltage 54.6 V

Output Current 1.5 A

Maximum Load 264LBS (120KG)

04
 Display Content

Display Content
AUTO

Sytem self-check

MPH
Current speed
Km/h

Battery level TURBO Sport mode

Single
STD Drive mode
Motor Mode

READY Ready to start ECO ECO mode

SPEED

Cruise control MAX

AVG
ERROR
MPH
Km/h
Top speed

Headlight Trip distance

KM
TRIP
MILE8

TEMP
C
F
Temperature

05
 Display Content

Note: After mode is set,

wait about 5 seconds
and the mode setting will
be saved automatically
and it will exit the interface.
1. Press the power button 2. Press the S button to change
to turn on the scooter speed levels (3 levels)10 mph,
18 mph, 25 mph

4. Press Horn button and the 3. Press and hold Power 5.Press Horn button and the
display reads "P10" (non-zero and horn buttons for 5-8 display reads "P20" (cruise
start); press M button and the seconds to enter mode control off); press M to switch
display reads "P11"(zero-start); setting interface to "P21"(cruise control on);
press S button to return to P10 press S to return to "P20"

06
 Display Content

Light switch ON/OFF

Horn

Power switch ON/OFF

Speed

Mode setting
Switch from KM/H to MPH

Power ON/OFF button :

Press and hold for 3S to power on / off.

Light switch :
Press the switch to turn on / off light.

Horn :
Press and hold to sound the horn.

S Speed :
Click the speed switch button to increase speed.

M Mode setting :
Switch from KM/H to MPH.

07
 Screen

Battery Level Display:

6-bar battery level.

6 Bars:
90%~100% of battery level

5 Bars:
70%~90% of battery level

Charging prompt
when the battery runs out and the scooter slides to a natural stop due to
inertia. So you have to charge it very soon. It is recommended not to drain the
battery by 100%. Charge it before use.

READY:
After turning on the E-scooter, the word "READY" appears on the instrument
display to remind rider to wear a helmet, knee pads, elbow pads, and abide by
traffic regulations when riding.

Activate Cruise Control:

After activating cruise control, you can release the thumb throttle, the scooter
moves at a uniform speed. After you press the brake to stop, press the throttle
again, and the scooter returns to the initial state.

Headlight:
After the scooter is powered on, press the headlight switch button by clicking
the multi-function switch. Symbols appear on the instrument display when all
the lights are turned on.
SPEED
Maximum Speed:
It shows the highest speed of the whole ride.

Current Speed:
The display shows the current speed during riding.

Trip distance:
Shows the travelled distance of a trip, and automatically resets to zero after
the scooter is powered off.

08
 E-SCOOTER APP

Download the "MiniRobot" app from the App Store(iPhone)

or Google Play (Android phone) for more information and
functions.

1.Turn on Bluetooth on 2.Function Settings 3.Bluetooth connected 4.Detailed information

your phone. Open the app interface
and tap search.

5.Tap to switch 6.Tap to lock the 7.Tap to turn on the 8.Tap to turn oncruise
Speed mode scooter rear wheel light control

09
 Assemble

1. Close the folding plug, buckle the lock, 2. Cut the tapes on the handlebar.Lift the
and twist the lock. handlebars on both sides up and slide
in to secure.

Attention

1. First, press down and hold 2. Fold the handlebars and tubes to the rear.
in the direction of the arrow,
and then pull up
in the direction of the arrow.

10
 Riding Basics

Wear a helmet, elbow pads, and knee pads in case of 1 Turn the power on, and check the battery
falls and injuries either you are a beginner learning to level indicator.
ride or you are a seasoned rider.

2 Stand with one foot on the deck and one 3 When the scooter starts to move forward,
foot on the ground. Scoot yourself with the put both feet on the deck and press the
foot on the ground. accelerator. (The accelerator initiates once
the speed exceeds 3 mph.)

4 Release the accelerator and the kinetic 5 Tilt your body to the steering direction as
energy recovery system (KERS) initiates you turn, and slowly turn the handlebar.
automatically to brake slowly; And squeeze
the brake lever for a sudden brake.
11
 Riding Notice

Do not ride in the heavy rain. Please keep a medium or low speed (5mph)
when you ride through speed bumps,
elevator door sills, bumpy roads or other
uneven surfaces Slightly bend your knee to
better adjust mentioned surfaces.

Look out for doors, elevators and other Do not accelerate when you go downhill.
overhead obstacles.

Do not press the accelerator when you're Always steer clear of obstacles.
walking alongside the scooter.
12
 Riding Notice

Do not hang heavy stuff on the handlebar. Keep both feet on the deck all time.

Dangerous Actions

Do not ride in traffic lanes or residential areas Do not turn the handlebar violently
where vehicles and pedestrians are both during high-speed riding.
allowed.

Do not ride in a ponding that is higher No passengers are allowed, including children.
than 2 INCH.
13
 Dangerous Actions

Keep your feet off the rear mudguard. Always keep your hands on the handlebar.

Do not touch the disc brake rotor. Do not try riding up or down stairs,
or jumping over obstacles.

Charging

Your scooter will be fully charged when the LED indicator on the
charger changes to green from red.
With charging protection, it will cut off charging automatically
after fully charge.
Even so, we still don't recommend charging your scooter for a long
time more than 24 hours at one time.
Do not connect the charger if the charging port is wet.
Keep the charging port closed when not charging.

14
 Disc Brake Adjustment

To adjust the disc brake sensitivity:

You need a hex wrench to remove the screws on the rocker.

• When the disc brake is too sensitive, rotate the disc brake rocker down a bit. Then, reinstall the
screws back to the brake cable core to tighten.

• When the disc brake cannot stop, rotate the disc brake rocker up a bit. Then, reinstall the screw
back to the brake cable core to tighten.
Notice: The disc brake may squeak when in use until it is broken in. This is normal and does not
affect the brake's function or performance.

To remove the disc brake noise,

First make sure the scooter is turned off. For easier operating, we suggest you put the scooter on
the desk.

• Loosen two screws on the pump (not the screw on the rocker).

• Adjust the position of the disc brake pump to ensure that the brake disc is in the middle of the
two brake pads.

• Keep the brake disc and brake pad not touching each other.

• Hold the disk brake pump in the desired position, then re-tighten the screws to the pump.

15
 Daily Care and Maintenance

Cleaning and Storage

If you see stains on the scooter's body, wipe them off with a damp cloth. If you cannot scrub off
the stain, put on some toothpaste, and brush them with a toothbrush, then wipe them off with a
damp cloth.

Notes
• Do not clean the scooter with alcohol, gasoline, kerosene, or other corrosive and volatile
chemical solvents to prevent dire damage.
• Do not wash the deck with a high-pressure water spray. During cleaning, make sure that the
scooter's turned off, the charging cable is unplugged, and the rubber flap is closed as water
leakage may result in electric shock or other major problems. When the scooter is not in use, keep
it indoors where it is dry and cool.

• Do not put it outdoors for a long time. Excessive sunlight, overheating, and over-cooling will
shorten the battery pack's lifespan.

Battery Maintenance
1 Use original battery packs. Use of batteries of other models or brands may bring about safety
issues;
2 Do not touch the contacts. Do not dismantle or puncture the casing. Keep the contacts away from
m etal objects to prevent short circuit which may result in battery damage or even injuries and
deaths;
3 Use original power adapter to avoid potential damage or fire;
4 Mishandling of used batteries may do tremendous harm to the environment. To protect natural
environment, please follow local regulations to properly dispose used batteries.
5 After every use, fully charge the battery to prolong its life span.

Storage and Disposal

1 Please try to store the scooter in a cool and dry place between 14℉ and 104℉. In extremely
humid environments the interior of the scooter may suffer condensation or even water accumula-
tion, which may damage the battery rapidly. Devices are not intended for use at elevations greater
than 2000 m above sea level. Prolonged Exposure to UV Rays, Rain and the Elements May
Damage the Enclosure Materials, Store Indoors When Not in Use.
2 In daily use, try to recharge the scooter after completely exhausting the battery. If the battery level
is low, charge it as soon as possible.
3 Please charge the scooter every other month to preserve the battery.

16
 Limited Warranty Statement

30 DAY SATISFACTION GUARANTEED RETURN POLICY

If you are unsatisfied with your purchase, iScooter’s return policy allows you to return the product purchased on
the Authorization channel within 30 days counting from the date of receipt of shipment, and request a refund
from the Authorization channel for any reason.
Note:Express shipping cost is non-refundable.
For the return request, iScooter is not responsible for lost packages due to the carrier, or products received that
cannot be verified. Received products that have damage determined to have been caused by the end-user may
be subject to denial of the return request.

TO QUALIFY FOR A REFUND, ALL THE FOLLOWING CONDITIONS MUST BE MET

1 A Return Merchandise Authorization (RMA) must be requested from iscooter within 30 days from the date
of receipt of shipment. To request an RMA, contact iScooter Service Team at [email protected].
2 The cost of return shipping will be borne by the customer.
3 For warranty service, please keep your receipt and/or invoice to validate proof of purchase.
4 Returned product must be in good physical condition (not physically broken or damaged).
5 All accessories originally included with your purchase must be included with your return.
6 If you return a product to iScooter, (a) without an RMA from iScooter(b) without all parts included in the
original package, iScooter retains the right to refuse delivery of such return.

LIMITED PRODUCT WARRANTY

iScooter warrants the original purchaser that your iScooter product shall be free from defects in materials and
workmanship under normal use for a period aforementioned.
iScooter does not warrant the operation of the product will be uninterrupted or error-free.
iScooter is not responsible for damage arising from failure to follow instructions relating to the product's usage.

REMEDIES
If a hardware defect is found and a valid claim is received by iScooter within the Warranty Period, iScooter will,
at its option and to the extent permitted by law, either (1) repair the product at no charge, using new or
refurbished replacement parts or, (2) replace the product with a new or refurbished product. In the event of a
defect, to the extent permitted by law, these are your sole and exclusive remedies. Shipping and handling
charges may apply except where prohibited by applicable law. This Limited Warranty is valid only in the
jurisdictions where the products are sold by [email protected], and is valid to the extent permitted by the
applicable laws of such jurisdictions.
Any replacement hardware product will be warranted for the remainder of the original warranty period or thirty
(30) days, whichever is longer, or for any additional period of time that may be applicable in your jurisdiction.

HOW TO OBTAIN WARRANTY SERVICE

A Warranty Service Order must be requested from iScooter within Warranty Period from the date of receipt of
shipment. To request a Warranty Service Order, contact iScooter Service Team [email protected].
To obtain warranty service, you must deliver the product, in either its original packaging or packaging providing
an equal degree of protection, to the address specified by iScooter. In accordance with applicable law,
iScooter may require the customer to furnish proof of purchase details and/or comply with registration
requirements before receiving warranty service.period or thirty (30) days, whichever is longer, or for any
additional period of time that may be applicable in your jurisdiction.

17
 Error Code

Error code Reason Maintenance and treatment

Check if there is a wrong wire connection or if there

4 Short-circuit fault is a short circuit in the installation, remove the short
circuit or replace the controller

Check whether the connection line between the

9 Motor communication fault
controller and the main controller is well connected.

Check whether the instrument panel and controller

Dashboard assembly cables are normal, turn off, remove the
10 assembly line interface, check the plug-in for slanting
communicationfault and loosening, and insert again after processing.
Power on, replace instrument or controller.

11 Check the motor and the phase line portion of the

Motor current fault
controller

Check whether the accelerator is completely reset,

14 Throttle fault check whether the accelerator and connection line
are normal, can disconnect the acceleration
connection line, and restart to exclude exceptions.

Check whether the brake handle is completely reset,

15 E-Brake fault can pull out the electronic brake cable, restart,
troubleshooting.

Start-up fault, check whether the motor Hall wiring is

normal, shut-off, pull out the assembly line interface
16 Motor communication fault
and check whether the plug-in is crooked, or bad
contact, correct, restart and troubleshooting

21 BMS communication fault

The voltage of the main line is too high, and the fault
is turned on. You should check whether the battery
50 Battery line fault voltage is normal and faulty during cycling. You
should replace the battery or controller to eliminate
the problem

Beyond the system load, restart, start up failure, the

53 Controller fault controller should be replaced to eliminate the
problem

Controller high The controller temperature is too high, static let the
55 car to cool and then restart. If the startup fails,
temperature alarm
replace the controller to eliminate the problem.

18
 FAQs
1 What if the E-Scooter comes arrived with missing accessories or broken parts?
A: Please take a photo and send to iScooter Support Team by sending email: And iScooter Support Team will
reply to you soon and send correct accessory or part replacement.

2 Is the tire replaceable and how to replace the tire?

A: Yes, the tire is replaceable. Please contact iScooter Support Team for more information or search the video
“How to replace the offroad tire”in YouTube instead.

3 What if the rear disc brake of the scooter doesn't work well?
A: You may please contact us for instructions of brake adjusting, or search "How to adjust rear brake of scooter"
in YouTube for tutorial video as well.

4 What if the rear disc brake of the scooter doesn't work well?
A: It usually means your disc brake tilts to cause friction noise. Please see Disc Brake Adjustment page. If you still
have problem, please contact us for help.

5 Why does the display read error code?

A: If you see any error code above, Please contact iScooter Support Team to remove the error code.

Contact Us
Contact us if you experience issues relating to riding, maintenance and safety, or errors/faults with
your iScooter iX3 electric scooter.
E-mail Service: [email protected]
www.iscooterglobal.com

19