Scribd
Upload
13 views2 pages

BestPrimer EP701_EN

Uploaded by

khoa.dang25061985
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
13 views2 pages

BestPrimer EP701_EN

Uploaded by

khoa.dang25061985
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Product Information BPEP701 Page 1 of 2

BestPrimer EP701
June 2017 Version Solvent-based epoxy primer, two components

BestPrimer EP701 is a solvent-based epoxy primer, two components, low


Description:
viscosity, high strength.

BestPrimer EP701 is low viscosity compound, high permeability. Used to make


a primer layer between the surfaces to be protected and the coating BestCoat
Recommended
layer, epoxy based to improve the bonding strength.
for:
BestPrimer EP701 can be applied to floors of concrete, cement plaster, fiber
cement panels, epoxy mortar ... workshops, warehouses, parking garages, ...

• High permeability should be able to link inside the material deeply.


• Linking well with all material surfaces, including metal surfaces.
• Improve the aesthetic and materials savings for next coating.
• Alkali resistance and high corrosion resistance.
• Easy to apply by popular tools such as brush, roller, nozzle ...
Advantage: • Easy to apply and materials saving because of allowing time application
is long.
• Level of consumption density is very low, so it should be economic and
efficient.
• Can be diluted with solvent to adjust the viscosity appropriate for each
specific application cases.

Technical Data:

Package: 5; 25 kg/set.

12 months from manufacturing date in sealed package and stored in


Shelf life:
cool and dry place.

Existence form: Viscosity liquid

Part A: Transparent
Color: Part B: Light yellow
A+B: Light yellow, transparent when curing.

Specific gravity: 0.98 ± 0.02 kg/liter (25oC)

Solid content: ≥ 40%

Consumption density: 0.10  0.25 kg/m2 /layer (Depending on surface condition)

Minimum: + 20oC (but above dew point temperature of 5oC)


Application
Maximum: + 35oC
temperature:
Relative humidity: 80%
Resistance of alkali, acid, water, salt solution, oil, fuel and other
Resistant chemical:
common chemicals.

Mechanical strength: Improve the bonding strength

Mixing ratio: Part A: Part B = 2:1 (By weight)


BPEP701 Page 2 of 2

Pot life:
Ambient temperature +20oC +25oC +30oC +35oC
Pot life 450 mins. 300 mins. 200 mins. 150 mins.

Interval time:
Ambient temperature +20oC +25oC +30oC +35oC
Interval time between two layer: Minimum 24 hrs 20 hrs 16 hrs 12 hrs
Maximum 3 days 2 days 2 days 2 days

Application:
For strong absorption and soft surfaces: Apply at least 02 primer layers before
coating BestCoat lines.
For flat surface, solid and average roughness: Apply 01 primer layer.
Substrate For hardener surface: Dilute BestPrimer EP701 with 10-15% of BestThinner
requirement: SC01 before application.
To achieve higher aesthetic and mechanical properties as required, surface
should be applied at least 01 layer of BestPrimer and 02 layers of coating paint
or self-leveling paint of BestCoat lines.

Concrete floor shall be cure for minimum 28 days, compressive strength: 


Substrate 20 MPa, tensile strength:  1.5 MPa.
preparation: Concrete floor shall be impurities, solid, flat, dry (moisture content ≤ 4%), the
impurities, crack, dust must be clean as required.
Two components A and B should be mixed thoroughly with mixer speed
300÷400 rpm. The mixing time at least is about 03 minutes or longer untill
Mixing:
materials is homogeneous as required. Keep materials is about 10-15%
minutes and mixing again before application.
Applied by a roller, a short brush or high pressure nozzle.
Note:
Application: Do not use materials which timed out applying and begin curing.
Application area should be cool and application instruction should be
downwind. Do not smoke during applying.

Clean tools, equipments with clean BestThinner SC01 before product


Cleaning:
hardening.
Both of two components are hazadous, flammable, therefore, they are required
to be placed distant from heat or fire during the execution or preservation.
This product can cause allergic to skin, therefore should be prevented from
directly skin contact.
Safety:
Should wear gloves, masks and glasses while handling the product.
In case of accidental eye contact, wash with fresh water and seek medical
advice immediately.
Keep away from fire, spark and heat sources when application.

The technical information and application instruction in documents of BESTMIX based on BESTMIX’s
current knowledge and practical experience. The information here only describes the general nature of
Disclaimer: product, so users should test the product for each purpose. BESTMIX has the right to change features of our
product, user must always refer the latest technology product.

You might also like