Scribd
Upload
8 views3 pages

flywheel C 6.4

Uploaded by

Chardy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
8 views3 pages

flywheel C 6.4

Uploaded by

Chardy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

26/11/24, 8:12 p.m. SIS 2.

2007/04/24 Flywheel - Install (KENR8106-09)

SMCS - 1156 i02744399

Installation Procedure
PSP
202 -0004
Table 1

01: 4/11/2 C508


Required Tools

Tool Part Number Part Description Qty


A 138-7575 1
KE 2:38- 7
Link Bracket 1

NOTICE
N
© 2 R81 05:00
024 06
Keep all parts clean from contaminants.

Cat
Contaminants may cause rapid wear and shortened component

erp
life.

illa
r In
c.
Always wear protective gloves when handling parts that have
been heated.

1. Perform the following procedure, if the ring gear was removed from the flywheel:

a. Raise the temperature of the ring gear 149 °C (300 °F).

b. Use a suitable press in order to install the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.

https://sis2.cat.com/?_ts=1717420528915#/print-preview/service/43dc85cd-7cee-4fdf-bf19-0824708643cd 1/3
26/11/24, 8:12 p.m. SIS 2.0

Illustration 1 g01374993
2. Install Tooling (A) and a suitable lifting device onto flywheel (3).

3. Install flywheel (3). The weight of flywheel (3) is approximately 50 kg (110 lb).

Illustration 2 g01374968

4. Install bolts (2) in order to secure flywheel (3) onto the crankshaft. Tighten bolts (2) to a torque
of 83 ± 5 N·m (61 ± 4 lb ft).

5. Remove Tooling (A) from flywheel (3).

https://sis2.cat.com/?_ts=1717420528915#/print-preview/service/43dc85cd-7cee-4fdf-bf19-0824708643cd 2/3
26/11/24, 8:12 p.m. SIS 2.0

Illustration 3 g01374966
6. Install muffler brackets (1).

7. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect" for
more information on flywheel runout.

End By:

a. Install the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".

b. Install the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".

PSP-0004C508
2024/11/27
01:11:38-05:00
i02744399
© 2024 Caterpillar Inc.

https://sis2.cat.com/?_ts=1717420528915#/print-preview/service/43dc85cd-7cee-4fdf-bf19-0824708643cd 3/3

You might also like