Scribd
Upload
16 views3 pages

4cae000496 Xmc20 Tuda1 English

Uploaded by

ajdinr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
16 views3 pages

4cae000496 Xmc20 Tuda1 English

Uploaded by

ajdinr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

XMC20 TUDA1

The serial interface unit brings powerful functions and high


flexibility for TDM data applications on the XMC20 platform

XMC20 TUDA1

TUDA1 provides different types


of data interfaces on one unit,
configurable via the network
Railways Oil & Gas

management system. With it PDH, SDH,

you can connect a wide range or Ethernet


network
Transport

of data terminal equipment, with


Power utilities
XMC20

different interface types and data


rate requirements to only one PC TUDA1

unit in one slot. This improves


subrack space utilization and Signals

optimises your investment.


Router Industrial PC

Telecontrol
networks

• 4 independent configurable serial ports on one single unit Enhanced data service capabilities in XMC20
• Configurable as V.35, X.24/V.11, V.24/V.28, RS-485, This unit addresses the specific needs of data services.
• Additional Ethernet interface
• Point-to-multipoint and multipoint-to-multipoint TUDA1 has access to XMC20’s TDM bus, which provides
• connections (centralised and distributed conferencing) 128 x E1 cross-connect capability. Each TUDA1 port has
2 Mbps access to the TDM bus. Low and high speed
• Subnetwork Connection Protection (SNCP)
data interfaces can be configured on TUDA1.
• 1+1 end-to-end path protection
• 1+1 equipment protection
• Shared protection ring
• Performance monitoring
• All functions from one network management system
Low speed interfaces intended for connection to controllers,valves
or detectors as well as high-speed interfaces for large bandwidth
applications, such as connections to routers or modems, are
available. In conjunction with the 2 Mbps interface unit SELI8,
TUDA1 can also be used as a data interface to E1 channel
converter, allowing up to 52 converters in one single XMC20.

A comprehensive set of protection mechanisms is available


in TUDA1, covering end-to-end traffic protection and
section protection for point-to-point applications, plus 1+1
equipment protection for redundancy of service units.

The XMC20 platform with TUDA1 also offers a shared protection


ring mechanism for protection of point-to-multipoint and
multipoint-to-multipoint connections in a ring topology.

Interface flexibility
TUDA1 provides four serial interface ports that can be
individually configured via the networks management
system in order to cover several types of applications.
Each port can be configured as:
• V.35
• X.24/V.11
• V.24/V.28
• RS-485 (2- and 4-wire mode)

An additional Ethernet interface is also available on TUDA1.


The access to the TDM bus is non-blocking, all interfaces
can be used in parallel. 02 TUDA1

Supplementary features Built-in transmission solution


In addition to the different types of interfaces supported, TUDA1 TUDA1, in conjunction with XMC20, provides a complete solution
offers extra features to enhance data services provisioning: for data services. With its wide range of available interfaces, the
• Subnetwork Connection Protection (SNCP) XMC20 can easily be deployed in any type of existing network
infrastructure. Data services provided via TUDA1 can be multiplexed
• 1+1 end-to-end path protection
and transmitted to the network using the TDM, SDH, and Ethernet
• Point-to-multipoint and multipoint-to-multipoint
(via SATP8) transport technologies of the XMC20 platform.
• connections (centralized and distributed conferencing)
• Shared protection ring
• 1+1 equipment protection (core functionality/conferencing)
• Performance monitoring
These attributes add even more advantages for data
services deployed from a XMC20 network.
Technical Data

Ports
5 interfaces (connector type) 4 serial (METRAL) + 1 x 10/100BaseT (RJ45)

Serial Interface Types


Configurable multi-protocol interfaces V.35, X.24/V.11, V.24/V.28, RS-485 (2-wire and 4-wire mode)

Data Rates Supported


Sub-rates (X.30/V.110) 0.6 … 38.4 kbps asynchronous and 0.6 … 56 kbps synchronous
n x 64 kbps 64 … 1,984 kbps (n = 1 … 31) synchronous
Transparent 0 … 600 kbps with oversampling

Ethernet Features
LAN 10/100 BaseT
WAN 64 … 1,984 kbps over TDM

Supplementary Features
Protections Subnetwork Connection Protection (SNCP), 1+1 end-to-end path protection,
Shared protection ring, 1+1 equipment protection
Connection types Point-to-point, point-to-multipoint, multipoint-to-multipoint, centralized conferencing
Performance monitoring According to ITU-T G.826

Management
ECST For local management
UNEM For central management

Power Supply
Input voltage nominal (min/max) –48/–60 V DC (–40.5 V DC … –72 V DC)

Operation Environment
Temperature range and humidity According to XMC20 environmental specifications

Hitachi Energy We reserve the right to make technical We reserve all rights in this document and in
[email protected] changes or modify the contents of this the subject matter and illustrations contained
© 2022 Hitachi Energy. All rights reserved. document without prior notice. With regard therein. Any reproduction, disclosure to
to purchase orders, the agreed particulars third parties or utilization of its contents – in
shall prevail. Hitachi Energy Ltd. does not whole or in parts – is forbidden without prior
accept any responsibility whatsoever for written consent of Hitachi Energy Ltd.
potential errors or possible lack of information
www.hitachienergy.com in this document. 4CAE000496

You might also like