DIMENSIONS SETTING

AXIAL VERSION RADIAL VERSION Setting of S50-Mx…A00

L 14.5 Position the sensor and reflector on opposite sides.
L 14.5 12 4 4 Find the points where the yellow LED (OUT) is switched ON and OFF in
both vertical and horizontal positions, and fix the sensor in the centre
between these points.

24

24
Setting of S50-Mx…B01/T01

14
S50-Mx SERIES 4 4

14.5 X 10
Position the sensor and reflector on opposite sides.
Turn the sensitivity trimmer to the maximum position.
Moving the sensor both vertically and horizontally, determine the power
INSTRUCTION MANUAL 2.5 X 10
on and off points of the yellow LED (OUT) and then mount the sensor in
the middle of the points defined. Optimum operation is obtained when
TRIMMER the green LED (mod.B01) is ON and the yellow LED is OFF.

M18x1

M12
6°
MODELS MODELS
B01 models: If necessary reduce sensitivity in order to detect very small
targets. In order to improve alignment, repeat the procedure detailed

M18x1
=

=
M12
with trimmer without trimmer with trimmer without trimmer
LED STABILITY

L 67 57 LED DI USCITA L 79 69 above whilst progressively reducing the sensitivity. A C

61
X 43 38 X 43 38 T01 model: Turn the sensitivity trimmer counterclockwise
CONTROLS
STABILITY LED
B
49 OUTPUT LED
until the yellow LED turns ON (pos.A). MIN MAX

FIBRE OPTIC VERSION Turn slowly the trimmer again clockwise until the yellow
OUTPUT LED (S50-Mx…A00/B01/C01/C10/C21/E01/F01/T01) 72.5 14.5
mm
LED turns OFF (Operating condition, pos.B).
The yellow LED ON indicates that the NO output status is closed. 12 10
Setting of S50-Mx…F01/G00/E01 with OF-43 (P/R fibre-optics)
STABILITY LED (S50-Mx…B01/C01/C21/E01/F01) Position the sensors (fibre terminals) on opposite sides.
CABLE VERSION
The green LED ON indicates that the received signal has a reserve Turn the sensitivity trimmer to maximum: moving the sensor both

24
M18x1

=
10
greater than 30% compared to the output switching value.

Ø22

M12
vertically and horizontally, determine the power on and off points of the
POWER ON LED (S50-Mx…G00) yellow LED (OUT) and then mount the sensor in the middle of the points
The green LED indicates that the sensor is operating. defined. Optimum operation is obtained when the green LED is ON and

Ø4
4 6.2
=
TRIMMER (S50-Mx…B01/C01/C21/E01/F01/T01) the yellow LED is OFF (the output function and the relative LEDs are
The trimmer can be used to adjust sensitivity; the operating distance 50 inverted in the E01 model with the OF-43 fibre).
increases turning the trimmer clockwise. TRIMMER
If necessary, reduce sensitivity using the trimmer, in order to detect very
small targets. In order to improve alignment, repeat the procedure
detailed above whilst progressively reducing the sensitivity.

Ø2.2
WARNING: The trimmer rotation is limited to 270° by a mechanical stop. STABILITY LED

Do not apply excessive torque when adjusting (max 40 Nmm). OUTPUT LED
Setting of S50-Mx…C01/C21/E01 with OF-42 (proximity fibre)
Turn the sensitivity trimmer to minimum: the green LED is ON, the
INSTALLATION
STABILITY LED

54.5
OUTPUT LED yellow LED is OFF. Position the target to detect in front of the sensor or
of the fibre terminals. Turn the sensitivity trimmer clockwise until the
The sensor can be fixed by means of the M18x1 threaded body through yellow LED turns ON (Target detected state, pos.A). Remove the target,
a ∅ 18mm hole, using the two CH.24 nuts enclosed (22Nm maximum TECHNICAL DATA the yellow LED turns OFF. Turn the sensitivity trimmer clockwise until
tightening torque). the yellow LED turns ON (Background detected state, pos.B).
Wide range of accessories available: various orientable fixing brackets S50-MA AXIAL VERSION S50-MR RADIAL VERSION The trimmer reaches maximum if the background is not detected.
ease the sensor positioning (please refer to the accessories listed in the Power supply: 10 … 30 Vdc (limit values) Turn the trimmer to the intermediate position C, between the two
general catalogue). Ripple: 2 Vpp max. positions A and B. The green LED must be ON.
The operating distance is measured from the front surface of the sensor Current consumption 35 mA max. Setting of S50-Mx…C10/D00
lens. (output current excluded):
The operating distance range of these sensors is factory preset: please
C/D models: To improve the detection, the Outputs: NO and NC; PNP or NPN (short-circuit protection) consider this feature when positioning.
object has to be moved closer or further away Output current: 100 mA max.
from the front surface of the sensor lens. Output saturation voltage: 2 V max.
Response time: 0.5 ms (2 ms mod.F01/G00)
TEST FUNCTION (S50-Mx…G00)
In case of lateral translation, the object must Switching frequency: 1KHz (250 Hz mod.F01/G00) The TEST+ and TEST- inputs can be used to inhibit the emitter and
move as indicated in the figure. Indicators: OUTPUT LED (YELLOW) excluding mod.G00 verify that the system is correctly operating.
STABILITY LED (GREEN) (mod.B01/C01/C21/E01/F01) The receiver output should switch when the test is activated while the
POWER ON LED (GREEN) (mod.G00) beam is uninterrupted.
Setting: sensitivity trimmer (mod.B01/C01/C21/E01/F01/T01) The inputs activating voltage range is 10 … 30 Vdc.
Operating temperature: -25 … 55 °C
CONNECTIONS Storage temperature: -25 … 70 °C
DECLARATION OF CONFORMITY
We DATASENSOR S.p.A. declare under our sole responsibility that
Electrical shock protection: Class 2
The connections are compliant to the EN 60947-5-2 standard. these products are conform to the 89/336 CEE, 73/23 CEE Directives
Operating distance (typical values): A00: 0.1…4m on R2
and successive amendments.
S50-Mx…G00 B01: 0.1…3.5m on R2 B01: 0.1…2m on R2
C01: 0…60cm C01: 0…35cm WARRANTY
BROWN 1 BROWN 1 C10: 0…10cm C10: 0…8cm
+ 10 … 30 Vdc
+ 10 … 30 Vdc DATASENSOR S.p.A. warrants its products to be free from defects.
C21: 0…35cm D00: 0…8cm DATASENSOR S.p.A. will repair or replace, free of charge, any product
WHITE 2 WHITE 2 D00: 0.5…10cm F01/G00: 0…10m found to be defective during the warranty period of 36 months from the
NC OUTPUT TEST +
F01/G00: 0…15m T01: 0.1…1m on R2 manufacturing date.
BLACK 4 BLACK 4
NO OUTPUT TEST - E01: 30mm with OF-42 / 100mm with OF-43 This warranty does not cover damage or liability deriving from the
BLUE 3 BLUE 3 T01: 0.1…1m on R2 improper application of DATASENSOR products.
0V 0V
Emission type: red (660 nm) (mod.B01/D00/E01/T01) / infrared (880nm) (mod.A00/C01/C10/C21/G00)
DATASENSOR S.p.A. Via Lavino 265
Ambient light rejection: according to EN 60947-5-2
40050 Monte S. Pietro - Bologna - Italy
Vibrations: 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6) Tel: +39 051 6765611 Fax: +39 051 6759324
M12 CONNECTOR Shock resistance: 11 ms (approx. 30 G) 6 shock for every axis (EN60068-2-27) http://www.datasensor.com e-mail: [email protected]
Housing material: Nickel-plated brass
2 1 Lens material: PMMA
DATASENSOR S.p.A. cares for the environment: 100%
recycled paper.
Mechanical protection: IP67 (TYPE 1 ENCLOSURE)
DATASENSOR S.p.A. reserves the right to make modifications
3 4 Connections: 2 m cable ∅ 4 mm / M12 - 4 pole connector and improvements without prior notification.
Weight: 110 g. max. cable vers. / 60 g. max. connector vers.
826001322 Rev.B
 DIMENSIONS SETTING
AXIAL VERSION RADIAL VERSION Setting of S50-Px…A00
L 14.5 L 14.5 Position the sensor and reflector on opposite sides.
2 1.5 12 2 1.5 Find the points where the yellow LED (OUT) is switched ON and OFF in
both vertical and horizontal positions, and fix the sensor in the centre
between these points.

24

24
=

=
Setting of S50-Px…B01/T01

3.8

3.8
14

14

14
S50-Px SERIES 3.5

4 4
3.5

4 4
Position the sensor and reflector on opposite sides.
Turn the sensitivity trimmer to the maximum position.
Moving the sensor both vertically and horizontally, determine the power
INSTRUCTION MANUAL
25 25

2.5 X 10 X
on and off points of the yellow LED (OUT) and then mount the sensor in
14.5 10
the middle of the points defined. Optimum operation is obtained when
the green LED (mod.B01) is ON and the yellow LED is OFF.
TRIMMER TRIMMER

B01 models: If necessary reduce sensitivity in order to A C

M18x1
=

=
MODELS MODELS

M18x1

=
detect very small targets. In order to improve alignment,

M12

M12
6°
with trimmer without trimmer with trimmer without trimmer
B
L 67 57 L 79 69 repeat the procedure detailed above whilst progressively MIN MAX
N°.2 Ø3.8 X 43 42 X 43 42
N°.2 Ø3.8
reducing the sensitivity.
CONTROLS
STABILITY LED STABILITY LED
X1 34 24 X1 46 36
X1 X1
15 OUTPUT LED 15 OUTPUT LED
T01 model: Turn the sensitivity trimmer counterclockwise until the yellow
FIBRE OPTIC VERSION LED turns ON (pos.A). Turn slowly the trimmer again clockwise until the
OUTPUT LED (S50-Px…A00/B01/C01/C10/C21/E01/F01/T01) 72.5 14.5
mm
yellow LED turns OFF (Operating condition, pos.B).
The yellow LED ON indicates that the NO output status is closed. 12 1.5
Setting of S50-Px…F01/G00/E01 with OF-43 (P/R fibre-optics)
STABILITY LED (S50-Px…B01/C01/C21/E01/F01) Position the sensors (fibre terminals) on opposite sides.
The green LED ON indicates that the received signal has a reserve CABLE VERSION
Turn the sensitivity trimmer to maximum: moving the sensor both
greater than 30% compared to the output switching value.

24
10
vertically and horizontally, determine the power on and off points of the

Ø22

14
POWER ON LED (S50-Px…G00) yellow LED (OUT) and then mount the sensor in the middle of the points
The green LED indicates that the sensor is operating. defined. Optimum operation is obtained when the green LED is ON and
4 4 6.2
TRIMMER (S50-Px…B01/C01/C21/E01/F01/T01) = the yellow LED is OFF (the output function and the relative LEDs are

Ø4
The trimmer can be used to adjust sensitivity; the operating distance inverted in the E01 model with the OF-43 fibre).
25 10
increases turning the trimmer clockwise. If necessary, reduce sensitivity using the trimmer, in order to detect very
TRIMMER
small targets. In order to improve alignment, repeat the procedure
WARNING: The trimmer rotation is limited to 270° by a mechanical stop. detailed above whilst progressively reducing the sensitivity.

Ø2.2

M18x1

=
Do not apply excessive torque when adjusting (max 40 Nmm).

M12
STABILITY LED
Setting of S50-Px…C01/C21/E01 with OF-42 (proximity fibre)
OUTPUT LED
Turn the sensitivity trimmer to minimum: the green LED is ON, the
INSTALLATION
N°.2 Ø3.8
STABILITY LED

OUTPUT LED
yellow LED is OFF. Position the target to detect in front of the sensor or
39.5 15
of the fibre terminals. Turn the sensitivity trimmer clockwise until the
The sensor can be fixed by means of the M18x1 threaded body through yellow LED turns ON (Target detected state, pos.A).
a ∅ 18mm hole, using the specific washer and the two CH.24 nuts TECHNICAL DATA Remove the target, the yellow LED turns OFF.
enclosed (1.5Nm maximum tightening torque). Turn the sensitivity trimmer clockwise until the yellow LED turns ON
Alternatively, the sensor can be mounted through the two housing’s S50-PA AXIAL VERSION S50-PR RADIAL VERSION (Background detected state, pos.B).
holes using two screws (M3x22 or longer) and washer. Power supply: 10 … 30 Vdc (limit values) The trimmer reaches maximum if the background is not detected.
Amongst the various possible solutions, we suggest to choose the Ripple: 2 Vpp max. Turn the trimmer to the intermediate position C, between the two
combination that offers the best visibility of the signalling LEDs and the Current consumption positions A and B. The green LED must be ON.
easiest access to the trimmer. 35 mA max.
(output current excluded): Setting of S50-Px…C10/D00
Wide range of accessories available: 22mm nuts, h=8mm, (2Nm Outputs: NO and NC; PNP or NPN (short-circuit protection) The operating distance range of these sensors is factory preset: please
maximum tightening torque) guarantee an improved torque and various Output current: 100 mA max. consider this feature when positioning.
orientable fixing brackets ease the sensor Output saturation voltage: 2 V max.
positioning (please refer to the accessories
listed in the general catalogue).
Response time: 0.5 ms (2 ms mod.F01/G00) TEST FUNCTION (S50-Px…G00)
Switching frequency: 1KHz (250 Hz mod.F01/G00)
The operating distance is measured from the
Indicators: OUTPUT LED (YELLOW) excluding mod.G00 The TEST+ and TEST- inputs can be used to inhibit the emitter and
front surface of the sensor lens.
STABILITY LED (GREEN) (mod.B01/C01/C21/E01/F01) verify that the system is correctly operating.
C/D models: To improve the detection, the
POWER ON LED (GREEN) (mod.G00) The receiver output should switch when the test is activated while the
object has to be moved closer or further away
Setting: sensitivity trimmer (mod.B01/C01/C21/E01/F01/T01) beam is uninterrupted.
from the front surface of the sensor lens.
Operating temperature: -25 … 55 °C The inputs activating voltage range is 10 … 30 Vdc.
In case of lateral translation, the object must
move as indicated in the figure. Storage temperature: -25 … 70 °C DECLARATION OF CONFORMITY
Electrical shock protection: Class 2 We DATASENSOR S.p.A. declare under our sole responsibility that
Operating distance (typical values): A00: 0.1…4m on R2
CONNECTIONS B01: 0.1…3.5m on R2 B01: 0.1…2m on R2
these products are conform to the 89/336 CEE, 73/23 CEE Directives
and successive amendments.
The connections are compliant to the EN 60947-5-2 standard. C01: 0…60cm C01: 0…35cm
C10: 0…10cm C10: 0…8cm WARRANTY
S50-Px…G00 C21: 0…35cm D00: 0…8cm DATASENSOR S.p.A. warrants its products to be free from defects.
D00: 0.5…10cm F01/G00: 0…10m DATASENSOR S.p.A. will repair or replace, free of charge, any product
BROWN 1 BROWN 1
+ 10 … 30 Vdc
+ 10 … 30 Vdc
F01/G00: 0…15m T01: 0.1…1m on R2 found to be defective during the warranty period of 36 months from the
E01: 30mm with OF-42 / 100mm with OF-43 manufacturing date. This warranty does not cover damage or liability
WHITE 2 WHITE 2 deriving from the improper application of DATASENSOR products.
NC OUTPUT TEST + T01: 0.1…1m on R2
BLACK 4 BLACK 4 Emission type: red (660 nm) (mod.B01/D00/E01/T01) / infrared (880nm) (mod.A00/C01/C10/C21/G00) DATASENSOR S.p.A. Via Lavino 265
NO OUTPUT TEST -
Ambient light rejection: according to EN 60947-5-2 40050 Monte S. Pietro - Bologna - Italy
BLUE 3 BLUE 3 Vibrations: 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6) Tel: +39 051 6765611 Fax: +39 051 6759324
0V 0V
Shock resistance: 11 ms (approx. 30 G) 6 shock for every axis (EN60068-2-27) http://www.datasensor.com e-mail: [email protected]
M12 CONNECTOR Housing material: PBT DATASENSOR S.p.A. cares for the environment: 100%
Lens material: PMMA recycled paper.
2 1 Mechanical protection: IP67 (TYPE 1 ENCLOSURE) DATASENSOR S.p.A. reserves the right to make modifications
Connections: 2 m cable ∅ 4 mm / M12 - 4 pole connector and improvements without prior notification.
3 4 Weight: 75 g. max. cable vers. / 25 g. max. connector vers.
826001242 Rev.B
 CONNECTIONS SETTING
The connections are compliant to the EN 60947-5-2 standard. Setting of S50-PL/ML…B01
Position the sensor and reflector on opposite sides.
S50-PL/ML…B01/C01/F01 S50-PL/ML…G00 M12 CONNECTOR Turn the sensitivity trimmer to the maximum position.
Moving the sensor both vertically and horizontally, determine the power
BROWN 1 BROWN 1
+ 10 … 30 Vdc
+ 10 … 30 Vdc ON and OFF points of the OUTPUT LED and then mount the sensor in
the middle of the points defined.
WHITE 2 WHITE 2
2 1 If necessary reduce sensitivity in order to detect very small targets.

S50-PL/ML SERIES N.C. OUTPUT TEST + In order to improve alignment, repeat the procedure detailed above
whilst progressively reducing the sensitivity.
BLACK 4 BLACK 4 3 4
N.O. OUTPUT NOT USED Setting of S50-PL/ML…F01/G00
INSTRUCTION MANUAL BLUE 3 BLUE 3
Position the sensors on opposite sides.
Turn the sensitivity trimmer to maximum: moving the sensor both
0V 0V vertically and horizontally, determine the power ON and OFF points of
the OUTPUT LED and then mount the sensor in the middle of the points
defined.
DIMENSIONS If necessary, reduce sensitivity using the trimmer, in order to detect very
small targets. In order to improve alignment, repeat the procedure
MODELS MODELS
S50-PL VERSIONS B/C/F version G version
S50-ML VERSIONS B/C/F version G version
detailed above whilst progressively reducing the sensitivity.
L 67 57
L 67 57 Setting of S50-PL/ML…C01
L 14.5 X 43 42 L 14.5
X1 34 24
X 43 38 Turn the sensitivity trimmer to minimum: the OUTPUT A C
2 1.5
LED is OFF.
Position the target to detect in front of the sensor. B
MAX
Turn the sensitivity trimmer clockwise until the MIN

24

24
=

=
CONTROLS OUTPUT LED turns ON (Target detected state, pos.A).

3.8
14
Remove the target, the OUTPUT LED turns OFF.
OUTPUT LED (S50-PL/ML…B01/C01/F01/)
3.5 Turn the sensitivity trimmer clockwise until the OUTPUT LED turns ON
The yellow LED ON indicates that the N.O. (normally open) output
4 4 4 4
(Background detected state, pos.B).
status is closed.
25 CABLE VERSION CABLE VERSION The trimmer reaches maximum if the background is not detected.
10 10
2.5 X 10 2.5 X 10 Turn the trimmer to the intermediate position C, between the two
POWER ON LED positions A and B.
TRIMMER
The green LED indicates that the sensor is operating.
TRIMMER

Ø4

Ø4
TRIMMER (S50-PL/ML…B01/C01/F01) TEST FUNCTION (S50-PL/ML…G00)
M18x1

M18x1
=

=
M12

M12
The trimmer can be used to adjust sensitivity; the operating distance
increases turning the trimmer clockwise. The TEST input can be used to inhibit the emitter and verify that the
N°.2 Ø3.8 POWER ON LED
POWER ON LED POWER ON LED POWER ON LED
system is correctly operating.
X1 15 OUTPUT LED OUTPUT LED OUTPUT LED OUTPUT LED
WARNING: The trimmer rotation is limited to 270° by a mechanical stop. mm
49
The receiver output should switch when the test is activated while the
Do not apply excessive torque when adjusting (max 40 Nmm). beam is uninterrupted.
TECHNICAL DATA The input activating voltage range is 10…30 Vdc.

INSTALLATION
S50-PL PLASTIC VERSIONS S50-ML METALLIC VERSIONS
S50-PL: The sensor can be fixed by means of the M18x1 threaded body Power supply: 10 … 30 Vdc (limit values)
through a ∅ 18 mm hole, using the specific washer and the two CH.24 Ripple: 2 Vpp max.
nuts enclosed (1.5 Nm maximum tightening torque). Current consumption 35 mA max. (mod.B01/C01/F01)
Alternatively, the sensor can be mounted through the two housing’s (output current excluded): 30 mA max (mod.G00)
holes using two screws (M3x22 or longer) and washer. Outputs: N.O. and N.C.; PNP or NPN (short-circuit protection)
Amongst the various possible solutions, we suggest to choose the Output current: 100 mA max.
combination that offers the best visibility of the signalling LEDs and the Output saturation voltage: 2 V max.
easiest access to the trimmer. Response time: 333 µs
22 mm nuts, h=8 mm, (2 Nm maximum tightening torque) are available
Switching frequency: 1,5 kHz
to guarantee an improved torque.
Indicators: OUTPUT LED (YELLOW) (mod.B01/C01/F01)
POWER ON LED (GREEN) DECLARATION OF CONFORMITY
We DATASENSOR S.p.A. declare under our sole responsibility that
S50-ML: The sensor can be fixed by means of the M18x1 threaded Setting: sensitivity trimmer (mod.B01/C01/F01)
these products are conform to the 89/336 CEE, 73/23 CEE Directives
body through a ∅ 18 mm hole, using the specific washer and the two Operating mode: LIGHT mode on N.O. output / DARK mode on N.C. output (mod.C01)
and successive amendments.
CH.24 nuts enclosed (22 Nm maximum tightening torque). DARK mode on N.O. output / LIGHT mode on N.C. output (mod.B01/F01)
Operating temperature: -10 … 50 °C WARRANTY
Storage temperature: -25 … 70 °C DATASENSOR S.p.A. warrants its products to be free from defects.
For both plastic version and metallic version are
Electrical shock protection: Class 2 DATASENSOR S.p.A. will repair or replace, free of charge, any product
available various orientable fixing brackets to
Operating distance (typical B01: 0.1…16 m on R2 found to be defective during the warranty period of 36 months from the
ease the sensor positioning (please refer to the
values): C01: 0…35 cm manufacturing date.
accessories listed in the general catalogue).
F01/G00: 0…60 m This warranty does not cover damage or liability deriving from the
The operating distance is measured from the
Emission type: RED LASER: Class 1 EN 60825-1 (1994) (mod.B01/C01/G00) improper application of DATASENSOR products.
front surface of the sensor lens.
In case of lateral translation, the object must Class II CDRH 21 CFR PART 1040.10 (mod.B01/C01/G00) DATASENSOR S.p.A. Via Lavino 265
move as indicated in the figure. Max. power ≤ 1 mW; Pulse = 4.5 µS; λ = 630…680nm; Frequency =25 kHz 40050 Monte S. Pietro - Bologna - Italy
Ambient light rejection: according to EN 60947-5-2 Tel: +39 051 6765611 Fax: +39 051 6759324
Vibrations: 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6) http://www.datasensor.com e-mail: [email protected]
Shock resistance: 11 ms (30 G) 6 shock for every axis (EN60068-2-27)
DATASENSOR S.p.A. cares for the environment: 100%
Housing material: PBT Nickel plated brass recycled paper.
Lens material: PMMA DATASENSOR S.p.A. reserves the right to make modifications
Mechanical protection: IP67 (TYPE 1 ENCLOSURE) and improvements without prior notification.
Connections: 2 m cable ∅ 4 mm / M12 - 4 pole connector
Weight: 75 g. max. cable vers./25 g. max. connector vers. 110 g. max. cable vers./60 g. max. connector vers. 826001341 Rev.B
 CONNECTIONS SETTING
The connections are compliant to the EN 60947-5-2 standard. EASY TOUCH 
The sensor uses the patent-covered EASY TOUCH technology that
M12 CONNECTOR allows a rapid and safe self-setting of the product.
Two different setting possibilities are available:
BROWN 1
+ 10 … 30 Vdc - EASY TOUCH; a long pressure of the SET pushbutton allows self-
setting.
WHITE 2 NC OUTPUT 2 1 + (BROWN)
10 … 30 Vdc - FINE DETECTION; to be used only in particularly critical conditions;
this setting procedure is used only when the EASY TOUCH is not
S50-PA/MA…M
NC OUTPUT (WHITE)
sufficient.
BLACK 4 3 4
Background suppression proximity NO OUTPUT 0V
(BLUE)
- NO OUTPUT
(BLACK)
Setting of S50-PA/MA…M
To achieve a correct sensor setting, the background or the object to be
BLUE 3 suppressied has to be present during self-setting.
0V
- EASY TOUCH (standard detection)
S50-PA/MA…N Place the background or the object to be suppressed inside the
operating range.
Foreground-background suppression Press the SET pushbutton until the READY/ERROR LED turns OFF.
DIMENSIONS Release the SET pushbutton and wait for the READY/ERROR LED to
proximity turn green.
The sensor is now ready to detect all objects in the set range
S50-PA VERSIONS S50-MA VERSIONS distinguishing them from the suppressed background (output LED
INSTRUCTION MANUAL 81.5 14.5 67 14.5
turns ON).
- Fine detection
2 1.5
Place the background or the object to be suppressed inside the
CONTROLS operating range.
Press the SET pushbutton. The READY/ERROR LED turns OFF.

24

24
=

=
3.8
Keep the SET pushbutton pressed until the READY/ERROR LED
14
OUTPUT LED
The yellow LED ON indicates that the NO output status is closed. blinks green.
3.5
The sensor performs a fine adjustment and is ready to detect objects
READY/ERROR LED (bicolour) 4 4 4 4
also very near the suppressed background (output LED turns ON).
When the bicoloured LED is continuously green, the sensor is operating 25 CABLE VERSION CABLE VERSION
in a normal condition and it is ready to function correctly (stability 2.5 43 10
10
2.5 43 10
10 Setting of S50-PA/MA…N
condition). To achieve a correct sensor setting, the object to be detected has to be
The red and green blinking of the LED indicates a wrong sensor setting.
SET PUSHBUTTON SET PUSHBUTTON
used during self-setting.

Ø4

Ø4
Please refer to the “SETTING” paragraph to get the correct setting - EASY TOUCH (standard detection)
M18x1

M18x1
=

=
M12

M12
procedure. Place the object to be detected in front of the sensor inside the
operating range.
SET PUSHBUTTON N°.2 Ø3.8
STABILITY LED STABILITY LED STABILITY LED STABILITY LED Press the SET pushbutton until the READY/ERROR LED turns OFF.
A long pressure on the pushbutton activates the self-setting procedure. 34 15 OUTPUT LED OUTPUT LED 49 OUTPUT LED OUTPUT LED
Release the SET pushbutton and wait for the READY/ERROR LED to
mm
turn green.
The sensor is ready to detect the object (output LED turns ON)
INSTALLATION excluding the background and foreground range (and thus any object
closer to the sensor respect to the reading field).
S50-PA…M/N: The sensor can be fixed by means of the M18x1 TECHNICAL DATA - Fine detection
threaded body through a ∅ 18mm hole, using the specific washer and Place the object to be detected inside the operating range.
the two CH.24 nuts enclosed (1.5Nm maximum tightening torque). S50-PA PLASTIC VERSIONS S50-MA METALLIC VERSIONS Press the SET pushbutton. The READY/ERROR LED turns OFF.
Alternatively, the sensor can be mounted through the two housing’s Power supply: 10 … 30 Vdc (limit values) Keep the SET pushbutton pressed until the READY/ERROR LED
holes using two screws (M3x22 or longer) and washer. Ripple: 2 Vpp max. blinks green.
Amongst the various possible solutions, we suggest to choose the Current consumption The sensor performs a fine adjustment and is ready to detect with
30 mA max.
combination that offers the best visibility of the signalling LEDs and the (output current excluded): better precision objects (output LED turns ON) at the pre-set
easiest access to the SET pushbutton. Outputs: NA and NC; PNP or NPN (short-circuit protection) operating distance, suppressing the background and foreground,
22mm nuts, h=8mm, (2Nm maximum tightening torque) are available to Output current: 100 mA max. even if the latter is very close to the sensing range.
guarantee an improved torque. Output saturation voltage: 2 V max.
Response time: 1 ms mod.M / 2 ms mod.N DECLARATION OF CONFORMITY
Switching frequency: 500 Hz mod.M / 250 Hz mod.N We DATASENSOR S.p.A. declare under our sole responsibility that
S50-MA…M/N: The sensor can be fixed by means of the M18x1
Indicators: OUTPUT LED (YELLOW) / READY/ERROR LED (GREEN/RED) these products are conform to the 89/336 CEE, 73/23 CEE Directives
threaded body through a ∅ 18mm hole, using the specific washer and
Setting: SET pushbutton and successive amendments.
the two CH.24 nuts enclosed (22Nm maximum tightening torque).
Operating mode: LIGHT mode on NO output / DARK mode on NC output WARRANTY
Data retention: non volatile EEPROM memory DATASENSOR S.p.A. warrants its products to be free from defects.
For both plastic version and metallic Operating temperature: -25 … 55 °C DATASENSOR S.p.A. will repair or replace, free of charge, any product
version are available various orientable Storage temperature: -25 … 70 °C found to be defective during the warranty period of 36 months from the
fixing brackets to ease the sensor Electrical shock protection: Class 2 manufacturing date.
positioning (please refer to the accessories Operating distance (typical background suppression 50…100 mm (mod.M) This warranty does not cover damage or liability deriving from the
listed in the general catalogue). values): foreground suppression 40…100 mm and background suppression 45…110mm mod.N) improper application of DATASENSOR products.
The operating distance is measured from Emission type: RED (630 nm) DATASENSOR S.p.A. Via Lavino 265
the front surface of the sensor lens. Ambient light rejection: according to EN 60947-5-2 40050 Monte S. Pietro - Bologna - Italy
To improve the detection, the object has to Vibrations: 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6) Tel: +39 051 6765611 Fax: +39 051 6759324
be moved closer or further away from the Shock resistance: 11 ms (approx. 30 G) 6 shock for every axis (EN60068-2-27) http://www.datasensor.com e-mail: [email protected]
front surface of the sensor lens.
Housing material: PBT Nickel plated brass DATASENSOR S.p.A. cares for the environment: 100%
In case of lateral translation, the object must move as indicated in the
Lens material: PMMA recycled paper.
figure.
Mechanical protection: IP67 (TYPE 1 ENCLOSURE) DATASENSOR S.p.A. reserves the right to make modifications
Connections: 2 m cable ∅ 4 mm / M12 - 4 pole connector and improvements without prior notification.
Weight: 75g. max. cable vers./25g. max. connector vers. 110g. max. cable vers./60g. max. connector vers.
826001013 Rev.C
 CONNECTIONS SETTING
The connections are compliant to the EN 60947-5-2 standard. Setting of S50-PH/MH…B01
Position the sensor and reflector on opposite sides.
S50-PH/MH…B01/C01/F01 S50-PH/MH…G00 M12 CONNECTOR Turn the sensitivity trimmer to the maximum position.
Moving the sensor both vertically and horizontally, determine the power
BROWN 1 BROWN 1
+ 10 … 30 Vdc + 10 … 30 Vdc ON and OFF points of the OUTPUT LED and then mount the sensor in
the middle of the points defined.
WHITE 2 WHITE 2 2 1 If necessary reduce sensitivity in order to detect very small targets.

S50-PH/MH SERIES N.C. OUTPUT TEST + In order to improve alignment, repeat the given procedure whilst
progressively reducing the sensitivity.
BLACK 4 BLACK 4 3 4
N.O. OUTPUT NOT USED Setting of S50-PH/MH…F01/G00
INSTRUCTION MANUAL BLUE 3 BLUE 3
Position the sensor and reflector on opposite sides.
Turn the sensitivity trimmer to maximum: moving the sensor both
0V 0V vertically and horizontally, determine the power ON and OFF points of
the OUTPUT LED and then mount the sensor in the middle of the points
defined.
DIMENSIONS If necessary, reduce sensitivity using the trimmer, in order to detect very
MODELS MODELS small targets. In order to improve alignment, repeat the procedure
S50-PH VERSION with without S50-MH VERSION with
trimmer
without
trimmer detailed above whilst progressively reducing the sensitivity.
trimmer trimmer
L 14.5 L 79 69 L 14.5 L 79 69 Setting of S50-PH/MH…C01
X 43 42 X 43 38
12 4 4
12 2 1.5 X1 46 36 Turn the sensitivity trimmer to minimum: the OUTPUT A C
LED is OFF.
Position the target to detect in front of the sensor. B

24
24
=

=
MAX
Turn the sensitivity trimmer clockwise until the MIN

14
3.8
14

14
CONTROLS 3.5
OUTPUT LED turns ON (Target detected state, pos.A).
Remove the target, the OUTPUT LED turns OFF.
4 4
OUTPUT LED (S50-PH/MH…B01/C01/F01/) 25
Turn the sensitivity trimmer clockwise until the OUTPUT LED turns ON
X CABLE VERS. CABLE VERS. (Background detected state, pos.B).
The yellow LED ON indicates that the N.O. (normally open) output 14.5 10 10 14.5 X 10 10
status is closed. The trimmer reaches maximum if the background is not detected.
TRIMMER
Turn the trimmer to the intermediate position C, between the two
POWER ON LED positions A and B.

Ø4
M18x1
Ø4
=
M18x1
The green LED indicates that the sensor is operating.

M12
6°
M12
6°

TRIMMER (S50-PH/MH…B01/C01/F01)
POWER ON LED
TEST FUNCTION (S50-PH/MH…G00)
The trimmer can be used to adjust sensitivity; the operating distance N°.2 Ø3.8 POWER ON LED
POWER ON LED OUTPUT LED
POWER ON LED
increases turning the trimmer clockwise. X1 15
OUTPUT LED
OUTPUT LED
61 OUTPUT LED
The TEST+ input can be used to deactivate the emitter and verify that
mm the system is operating correctly.
WARNING: The trimmer rotation is limited to 270° by a mechanical stop. The receiver output should switch when the test is activated while the
Do not apply excessive torque when adjusting (max 40 Nmm). TECHNICAL DATA beam is uninterrupted.
The input activating voltage range is 10…30 Vdc.
INSTALLATION S50-PH PLASTIC VERSIONS S50-MH METAL VERSIONS
Power supply: 10 … 30 Vdc limit values
S50-PH: The sensor can be fixed by means of the M18x1 threaded body
Ripple: 2 Vpp max.
through a ∅ 18 mm hole, using the specific washer and the two CH.24
nuts enclosed (1.5 Nm maximum tightening torque). Current consumption 35 mA max. (mod.B01/C01/F01)
Amongst the various possible solutions, we suggest to choose the (output current excluded): 30 mA max (mod.G00)
combination that offers the best visibility of the signalling LEDs and the Outputs: N.O. and N.C.; PNP or NPN (short-circuit protection)
easiest access to the trimmer. Output current: 100 mA max.
22 mm nuts, h=8 mm, (2 Nm maximum tightening torque) are available Output saturation voltage: 2 V max.
to guarantee an improved torque. Response time: 333 µs
Switching frequency: 1.5 kHz
S50-MH: The sensor can be fixed by means of the M18x1 threaded
Indicators: OUTPUT LED (YELLOW) (mod.B01/C01/F01)
body through a ∅ 18 mm hole, using the specific washer and the two POWER ON LED (GREEN) DECLARATION OF CONFORMITY
CH.24 nuts enclosed (22 Nm maximum tightening torque).
Setting: sensitivity trimmer (mod.B01/C01/F01) We DATASENSOR S.p.A. declare under our sole responsibility that
Operating mode: LIGHT mode on N.O. output / DARK mode on N.C. output (mod.C01) these products are conform to the 89/336 CEE, 73/23 CEE Directives
Various orientable fixing brackets for both plastic and metallic versions DARK mode on N.O. output / LIGHT mode on N.C. output (mod.B01/F01) and successive amendments.
are available to ease sensor positioning (please refer to the accessories Operating temperature: -10 … 50 °C
WARRANTY
listed in the general catalogue). Storage temperature: -25 … 70 °C
DATASENSOR S.p.A. warrants its products to be free from defects.
The operating distance is measured from the front surface of the sensor Electrical shock protection: Class 2 DATASENSOR S.p.A. will repair or replace, free of charge, any product
lens. Operating distance (typical values): B01: 0.1…9 m on R2 reflector found to be defective during the warranty period of 36 months from the
C01: 0…25 cm manufacturing date.
F01/G00: 0…50 m This warranty does not cover damage or liability deriving from the
Emission type: RED LASER: Class 1 EN 60825-1 (1994) (mod.B01/C01/G00) improper application of DATASENSOR products.
Class II CDRH 21 CFR PART 1040.10 (mod.B01/C01/G00)
Max. power ≤ 1 mW; Pulse = 4.5 µs; λ = 630…680 nm; Frequency =25 kHz DATASENSOR S.p.A. Via Lavino 265
Ambient light rejection: According to EN 60947-5-2 40050 Monte S. Pietro - Bologna - Italy
Vibrations: 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6) Tel: +39 051 6765611 Fax: +39 051 6759324
http://www.datasensor.com e-mail: [email protected]
Shock resistance: 11 ms (30 G) 6 shock for every axis (EN60068-2-27)
Housing material: PBT Nickel-plated brass DATASENSOR S.p.A. cares for the environment: 100%
Lens material: PMMA recycled paper.
Mechanical protection: IP67 (TYPE 1 ENCLOSURE) DATASENSOR S.p.A. reserves the right to make modifications
and improvements without prior notification.
Connections: 2 m cable ∅ 4 mm / M12 - 4 pole connector
Weight: 75 g. max. cable vers. /25 g. max. conn. vers. 110 g. max. cable vers. /60 g. max. conn. vers. 826001681 Rev.A
 CONNECTIONS SETTING
The connections are compliant to the EN 60947-5-2 standard. EASY TOUCH 
M12 CONNECTOR The sensor uses the patent-covered EASY TOUCH technology that
allows a rapid and safe self-setting of the product.
BROWN 1
+ 10 … 30 Vdc Two different setting possibilities are available:
- EASY TOUCH; press for 2 sec. of the SET pushbutton allows self-
WHITE 2 NC OUTPUT 2 1 + 10 … 30 Vdc setting.
NC OUTPUT (WHITE) (BROWN)
- FINE DETECTION; to be used only in particularly critical conditions;

S50-PS/MS…M BLACK 4
NO OUTPUT 0V-
(BLUE)
3 4
NO OUTPUT
(BLACK)
this setting procedure is used only when the EASY TOUCH is not
sufficient.
Background suppression BLUE 3
0V
Setting of S50-PS/MS…M
To set correctly the sensor, the background or object to be suppressed
has to be present during self-setting.
DIMENSIONS - EASY TOUCH (standard detection)
Place the background or the object to be suppressed inside the
S50-PS VERSION S50-MS VERSION
operating range.

INSTRUCTION MANUAL 79 14.5 79 14.5 Press the SET pushbutton until the READY/ERROR LED turns OFF.
Release the SET pushbutton and wait for the READY/ERROR LED to
22 22 turn green.
The sensor is now ready to detect all objects in the set range
CONTROLS distinguishing them from the suppressed background (output LED

24

24
turns ON).

14

14
OUTPUT LED - Fine detection
The yellow LED ON indicates that the NO output is closed. Place the background or the object to be suppressed inside the
6 10 6 10
READY/ERROR (bicoloured) LED operating range.
When permanently green indicates a normal operating conditions and 24.5 42 24.5 33 Press the SET pushbutton and keep it pressed until the
the sensor is ready to function correctly (stability condition). The SET PUSHBUTTON SET PUSHBUTTON
READY/ERROR LED turns OFF and then begins to blinks green.
alternative green / red blinking indicates a wrong detection. The sensor in this case makes a fine setting and is ready to detect
Please refer to the “SETTING” paragraph for acquisition or setup with better precision objects different from the background (output

M18
16.8

M12

M18
16.8

M12
procedure indications. LED turns ON) .
SET PUSHBUTTON STABILITY LED STABILITY LED
A long pressure on the pushbutton activates the self-setting procedure. OUTPUT LED OUTPUT LED
46 25
CABLE VERSION CABLE VERSION
10 10
INSTALLATION

Ø4

Ø4
S50-PS…M: The sensor can be fixed by means of the M18x1 threaded
body through a ∅ 18mm hole, using the specific washer and the two
CH.24 nuts enclosed (1.5Nm maximum tightening torque).
Alternatively, the sensor can be mounted through the two housing’s
holes using two screws (M3x22 or longer) and washer. STABILITY LED STABILITY LED

Amongst the various possible solutions, we suggest to choose the OUTPUT LED
mm
OUTPUT LED
combination that offers the best visibility of the signalling LEDs and the
easiest access to the SET pushbutton.
22mm nuts, h=8mm, (2Nm maximum tightening torque) are available to
TECHNICAL DATA
guarantee an improved torque. S50-PS PLASTIC VERSIONS S50-MS METAL VERSIONS
S50-MS…M: The sensor can be fixed by means of the M18x1 threaded Power supply: 10 … 30 Vdc limit values
body through a ∅ 18mm hole, using the specific washer and the two Ripple: 2 Vpp max.
CH.24 nuts enclosed (22Nm maximum tightening torque). Current consumption 30 mA max.
(output current excluded):
For both plastic version and metallic version are available various Outputs: NO and NC; PNP or NPN (short-circuit protection)
orientable fixing brackets to ease the sensor positioning (please refer to Output current: 100 mA max. DECLARATION OF CONFORMITY
the accessories listed in the general catalogue). Output saturation voltage: 2 V max. We DATASENSOR S.p.A. declare under our sole responsibility that
Response time: 1 ms these products are conform to the 89/336 CEE, 73/23 CEE Directives
The operating distance is measured and successive amendments.
Switching frequency: 500 Hz
from the front surface of the sensor Indicators: OUTPUT LED (YELLOW) / READY/ERROR LED (GREEN/RED) WARRANTY
lens.
Setting: SET pushbutton DATASENSOR S.p.A. warrants its products to be free from defects.
For the best detection, the object has to
Operating mode: LIGHT mode on NO output / DARK mode on NC output DATASENSOR S.p.A. will repair or replace, free of charge, any product
move closer or further away from this
Data retention: EEPROM non volatile memory found to be defective during the warranty period of 36 months from the
surface. In presence of a lateral
Operating temperature: -25 … 55 °C manufacturing date.
movement, the object has to move as
Storage temperature: -25 … 70 °C This warranty does not cover damage or liability deriving from the
indicated in the drawing.
Electrical shock protection: Class 2 improper application of DATASENSOR products.
Operating distance (typical values): 15…100 mm proximity; 50…100 mm background suppression DATASENSOR S.p.A. Via Lavino 265
Emission type: red (670 nm) 40050 Monte S. Pietro - Bologna - Italy
Ambient light rejection: According to EN 60947-5-2 Tel: +39 051 6765611 Fax: +39 051 6759324
Vibrations: 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6) http://www.datasensor.com e-mail: [email protected]
Shock resistance: 11 ms (approx. 30 G) 6 shock for every axis (EN60068-2-27) DATASENSOR S.p.A. cares for the environment: 100%
Housing material: PBT Nickel-plated brass recycled paper.
Lens material: PMMA DATASENSOR S.p.A. reserves the right to make modifications
Mechanical protection: IP67 (TYPE 1 ENCLOSURE) and improvements without prior notification.
Connections: 2 m cable ∅ 4 mm / M12 - 4 pole connector
Weight: 90g. max. cable vers. /40g. max. conn. vers. 125g. max. cable vers. /75g. max. conn. vers.. 826001671 Rev.A
 SETTING
CONNECTIONS
The supplied sensor is set at the maximum sensitivity, allowing the
The connections are compliant to the EN 60947-5-2 standard. detection of the minimum luminescence intensity. No other setting
procedure is necessary, unless luminescent objects placed on
M12 CONNECTOR luminescence backgrounds have to be detected.
BROWN 1
+ 10 … 30 Vdc EASY TOUCH 
The sensor uses the patent-covered EASY TOUCH technology that
WHITE 2 NC OUTPUT + (BROWN)
10 … 30 Vdc allows a rapid and safe self-setting of the product.
S50-PA/MA…U (WHITE)
2 1
NC OUTPUT Two different setting possibilities are available:
- EASY TOUCH; a long pressure of the SET pushbutton allows self-
BLACK 4 3 4
Luminescence sensor NO OUTPUT 0V - NO OUTPUT setting.
(BLUE) (BLACK) - FINE DETECTION; to be used only in particularly critical conditions,
BLUE 3 this setting procedure is used only when the EASY TOUCH is not
0V sufficient.

INSTRUCTION MANUAL Setting of S50-PA/MA…U

To achieve a correct sensor functioning, the luminescence mark or
DIMENSIONS object to be detected has to be placed at the right reading distance.
- EASY TOUCH (standard detection in the LIGHT mode)
S50-PA VERSIONS S50-MA VERSIONS The EASY TOUCH technology allows the functioning in the LIGHT
CONTROLS 81.5 14.5 67 14.5 mode (mark presents a higher luminescence respect to the
2 1.5 background).
OUTPUT LED The mark to detect has to be placed correctly at the right reading
The yellow LED ON indicates that the NO output status is closed. distance within the sensor spot.
READY/ERROR LED (bicolour) Press the SET pushbutton until the READY/ERROR LED turns OFF.

24

24
=

=
3.8
14
When the bicoloured LED is continuously green, the sensor is operating Release the SET pushbutton and wait for the READY/ERROR LED to
in a normal condition and it is ready to function correctly (stability 3.5 turn green.
condition). 4 4 4 4 The sensor is now ready to detect the pre-set luminescent mark or
The red and green blinking of the LED indicates a wrong sensor setting. 25 CABLE VERSION CABLE VERSION object (output LED turns ON when the NO output is closed).
Please refer to the “SETTING” paragraph to get the correct setting 2.5 43 10
10
2.5 43 10
10 Note: The automatic EASY TOUCH setting has to be performed
procedure. without any objects inside the sensor reading range (or using a non-
luminescent object) in order to bring the sensor back to the maximum
SET PUSHBUTTON SET PUSHBUTTON

Ø4

Ø4
SET PUSHBUTTON sensitivity condition.
A long pressure on the pushbutton activates the self-setting procedure.
M18x1

M18x1
=

=
M12

M12
- Fine detection (DARK or LIGHT mode)
N°.2 Ø3.8
This mode offers an improved detection precision and aIso allows the
STABILITY LED
STABILITY LED
OUTPUT LED
STABILITY LED STABILITY LED

OUTPUT LED
detection of luminescent marks or objects placed on luminescent
34 15 OUTPUT LED 49 OUTPUT LED
mm backgrounds.
The operating mode is selected automatically by the sensor:
INSTALLATION DARK operating mode (mark presents a lower luminescence respect
S50-PA…U: The sensor can be fixed by means of the M18x1 threaded TECHNICAL DATA to the background) or LIGHT operating mode (mark presents a higher
luminescence respect to the background).
body through a ∅ 18mm hole, using the specific washer and the
The mark to detect has to be placed correctly at the right reading
enclosed 24mm nuts (maximum torque of tightening 1.5Nm). S50-PA PLASTIC VERSIONS S50-MA METALLIC VERSIONS
distance within the sensor spot.
Alternatively, the sensor can be mounted through the two housing’s Power supply: 10 … 30 Vdc (limit values) Press the SET pushbutton. The READY/ERROR LED turns OFF.
holes using two screws (M3x22 or longer) and nuts. Ripple: 2 Vpp max. Keep the SET pushbutton pressed until the READY/ERROR LED
Amongst the various possible solutions, we suggest to choose the Current consumption
25 mA max. blinks green. Place the background under the sensor spot.
combination that offers the best visibility of the signalling LEDs and the (output current excluded): Press the SET pushbutton again until the READY/ERROR LED turns
easiest access to the SET pushbutton.
Outputs: NA and NC; PNP or NPN (short-circuit protection) OFF. The sensor is now ready to detect, with a very high precision,
22mm nuts, h=8mm, (2Nm maximum tightening torque) are available to
Output current: 100 mA max. the pre-set luminescent mark (output LED turns ON, READY/ERROR
guarantee an improved torque.
Output saturation voltage: 2 V max. LED turns green).
Response time: 500 µs
S50-MA…U: The sensor can be fixed by means of the M18x1 threaded Switching frequency: 1 KHz
body through a ∅ 18mm hole, using the specific washer and the two Indicators: OUTPUT LED (YELLOW) / READY/ERROR LED (GREEN/RED) DECLARATION OF CONFORMITY
CH.24 nuts enclosed (22Nm maximum tightening torque). We DATASENSOR S.p.A. declare under our sole responsibility that
Setting: SET pushbutton
For both plastic version and metallic version are available various these products are conform to the 89/336 CEE, 73/23 CEE Directives
Operating mode: LIGHT mode on NO output / DARK mode on NC output
orientable fixing brackets to ease the sensor positioning (please refer to and successive amendments.
Data retention: non volatile EEPROM memory
the accessories listed in the general catalogue). Operating temperature: -10 … 55 °C WARRANTY
Storage temperature: -20 … 70 °C DATASENSOR S.p.A. warrants its products to be free from defects.
10...15° 10...15° Electrical shock protection: Class 2 DATASENSOR S.p.A. will repair or replace, free of charge, any product
The operating distance is measured
from the front surface of the sensor Operating distance (typical found to be defective during the warranty period of 36 months from the
8…20mm range, maximum signal at 10 mm manufacturing date.
lens. values):
To detect luminescent marks on This warranty does not cover damage or liability deriving from the
Å Æ Minimum spot dimension: 3 mm
reflective surfaces, position the improper application of DATASENSOR products.
Emission type: LED UV (370 nm)
sensor axis at 10°…15° respect to Ambient light rejection: according to EN 60947-5-2 DATASENSOR S.p.A. Via Lavino 265
the orthogonal line of the surface to Vibrations: 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6) 40050 Monte S. Pietro - Bologna - Italy
detect. Tel: +39 051 6765611 Fax: +39 051 6759324
Shock resistance: 11 ms (approx. 30 G) 6 shock for every axis (EN60068-2-27)
Housing material: PBT Nickel plated brass http://www.datasensor.com e-mail: [email protected]
Lens material: PMMA DATASENSOR S.p.A. cares for the environment: 100%
Mechanical protection: IP67 (TYPE 1 ENCLOSURE) recycled paper.
Connections: 2 m cable ∅ 4 mm / M12 - 4 pole connector DATASENSOR S.p.A. reserves the right to make modifications
and improvements without prior notification.
Weight: 75g. max. cable vers./25g. max. connector vers. 110g. max. cable vers./60g. max. connector vers.
826001032 Rev.C
 SETTING
CONNECTIONS
EASY TOUCH 
The connections are compliant to the EN 60947-5-2 standard. The sensor uses the patent-covered EASY TOUCH technology that
allows a rapid and safe self-setting of the product.
M12 CONNECTOR Two different setting possibilities are available:
BROWN 1 - EASY TOUCH; a long pressure of the SET pushbutton allows self-
+ 10 … 30 Vdc
setting.
- FINE DETECTION; to be used only in particularly critical conditions,
WHITE 2 N.C. OUTPUT 2 1 + 10 … 30 Vdc
S50-PA/MA…W
this setting procedure is used only when the EASY TOUCH is not
N.C. OUTPUT (WHITE) (BROWN)
sufficient.
BLACK 4 3 4
Contrast sensor N.O. OUTPUT 0V
(BLUE)
- N.O. OUTPUT
(BLACK)
Setting of S50-PA/MA…W
To achieve a correct sensor functioning, the coloured mark or object to
BLUE 3 be detected has to be placed at the right reading distance.
0V
- EASY TOUCH (standard detection in the DARK mode)
INSTRUCTION MANUAL The EASY TOUCH technology allows the functioning in the DARK
mode (mark presents a lower light intensity respect to the
DIMENSIONS background).
The mark to detect has to be placed correctly at the right reading
S50-PA VERSIONS S50-MA VERSIONS distance within the sensor spot.
CONTROLS 81.5 14.5 67 14.5 Press the SET pushbutton until the READY/ERROR LED turns OFF.
2 1.5 Release the SET pushbutton and wait for the READY/ERROR LED to
OUTPUT LED turn green.
The yellow LED on indicates that the N.O. (normally open) output status The sensor is now ready to detect the pre-set coloured mark or object
(output LED turns ON when the N.O. output is closed).

24
24
=

=
is closed.

3.8
14
READY/ERROR LED (bicolour) - Fine detection (DARK or LIGHT mode)
When the bicoloured LED is continuously green, the sensor is operating
3.5
This mode offers an improved detection precision.
4 4 4 4
in a normal condition and it is ready to function correctly (stability The sensor can function either in the DARK operating or in the LIGHT
condition). 25 CABLE VERSION CABLE VERSION operating mode (light-coloured mark ON dark background).
10 10
The red and green blinking of the LED indicates a wrong sensor setting. 2.5 43 10 2.5 43 10 The operating mode is selected automatically by the sensor.
Please refer to the “SETTING” paragraph to get the correct setting SET PUSHBUTTON SET PUSHBUTTON The mark to detect has to be placed correctly at the right reading
procedure. distance within the sensor spot.

Ø4

Ø4
Press the SET pushbutton. The READY/ERROR LED turns OFF.
M18x1

M18x1
=

=
M12

M12
SET PUSHBUTTON Keep the SET pushbutton pressed until the READY/ERROR LED
A long pressure on the pushbutton activates the self-setting procedure. blinks green. Place the background under the sensor spot.
N°.2 Ø3.8 STABILITY LED
STABILITY LED
OUTPUT LED
STABILITY LED STABILITY LED
Press the SET pushbutton again until the READY/ERROR LED turns
34 15 OUTPUT LED 49 OUTPUT LED OUTPUT LED
mm OFF.
The sensor is now ready to detect, with a very high precision, the pre-
set coloured mark (output LED turns ON, READY/ERROR LED turns
INSTALLATION TECHNICAL DATA green).
The output LED is ON and the N.O. output is closed, when the sensor
S50-PA PLASTIC VERSIONS S50-MA METALLIC VERSIONS is positioned on the pre-set coloured mark.
S50-PA…W: The sensor can be fixed by means of the M18x1 threaded
Power supply: 10 … 30 Vdc (limit values)
body through a ∅ 18 mm hole, using the specific washer and the NOTE
Ripple: 2 Vpp max.
enclosed 24 mm nuts (maximum torque of tightening 1.5 Nm). If a setting error will occur please repeat again the EASY TOUCH
Alternatively, the sensor can be mounted through the two housing’s Current consumption setting procedure, in order to be sure to restart the setting procedure
25 mA max.
holes using two screws (M3x22 or longer) and nuts. (output current excluded): correctly.
Amongst the various possible solutions, we suggest to choose the Outputs: N.O. and N.C.; PNP or NPN; 30 Vcc max. (short-circuit protection)
combination that offers the best visibility of the signalling Leeds and the Output current: 100 mA max.
easiest access to the SET pushbutton. Output saturation voltage: 2 V max.
Response time: 100 µs
22 mm nuts, h=8 mm, (2 Nm maximum tightening torque) are available Switching frequency: 5 kHz
to guarantee an improved torque. Indicators: OUTPUT LED (YELLOW) / LED READY/ERROR (GREEN/RED) DECLARATION OF CONFORMITY
Setting: SET pushbutton We DATASENSOR S.p.A. declare under our sole responsibility that
Operating mode: LIGHT mode on N.O. output / DARK mode on N.C. output these products are conform to the 89/336 CEE, 73/23 CEE Directives
S50-MA…W: The sensor can be fixed by means of the M18x1 threaded Data retention: non volatile EEPROM memory and successive amendments.
body through a ∅ 18 mm hole, using the specific washer and the two Operating temperature: -10 … 55 °C WARRANTY
CH.24 nuts enclosed (22 Nm maximum tightening torque). Storage temperature: -20 … 70 °C DATASENSOR S.p.A. warrants its products to be free from defects.
For both plastic version and metallic version are available various Electrical shock protection: Class 2 (TYPE 1 ENCLOSURE) DATASENSOR S.p.A. will repair or replace, free of charge, any product
orientable fixing brackets to ease the sensor positioning (please refer to Operating distance (typical found to be defective during the warranty period of 36 months from the
10 mm ±2 mm
the accessories listed in the general catalogue). values): manufacturing date.
Minimum spot dimension: 4.5 mm This warranty does not cover damage or liability deriving from the
Emission type: white light LED (400-700 nm) improper application of DATASENSOR products.
The operating distance is measured from the front surface of the sensor
Ambient light rejection: according to EN 60947-5-2 DATASENSOR S.p.A. Via Lavino 265
lens.
Vibrations: 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6) 40050 Monte S. Pietro - Bologna - Italy
Shock resistance: 11 ms (30 G) 6 shock for every axis (EN60068-2-27) Tel: +39 051 6765611 Fax: +39 051 6759324
Housing: PBT Nickel plated brass http://www.datasensor.com e-mail: [email protected]
Lenses: PMMA DATASENSOR S.p.A. cares for the environment: 100%
Mechanical protection: IP67 (TYPE 1 ENCLOSURE) recycled paper.
Connections: 2 m cable ∅ 4 mm / M12 - 4 pole connector DATASENSOR S.p.A. reserves the right to make modifications
Weight: 75 g. max. cable vers./25 g. max. connector vers. 110 g. max. cable vers./60 g. max. connector vers. and improvements without prior notification.
826001041 Rev.B
 SETTING
CONNECTIONS
No sensor setting is necessary.
The connections are compliant to the EN 60947-5-2 standard. The user has to select the direct or inverse proportionality of the output
respect to the object’s distance inside the operating field. This is
M12 CONNECTOR obtained by means of the DIR/INV input.
BROWN The direct proportionality is set connecting the DIR/INV input to +Vdc;
+ 18 … 30 Vdc

WHITE DIR/INV + (BROWN)

18 … 30 Vdc 10

S50-PA/MA…Y DIR/INV (WHITE)

2 1
8
BLACK 3 4
Distance sensor ANALOG 0V - ANALOG OUTPUT
6
OUTPUT (BLUE) (BLACK)

BLUE
0V 4

INSTRUCTION MANUAL 2

0
DIMENSIONS 0 20 40 60 80 100 120

CONTROLS DIRECT PROPORTIONALITY (DIR)

the inverse proportionality is set connecting the DIR/INV input to 0V.

OUTPUT LED S50-PA VERSIONS S50-MA VERSIONS
The yellow LED indicates the analogue output status, changing its 81.5
emission intensity. 67 14.5 10
2 1.5
FIELD LED
The red LED on indicates that the object to detect is outside the sensor 8
operating field.

24

24
=

=
3.8
14

6
3.5

4 4 4 4 4
INSTALLATION CABLE VERSION CABLE VERSION
10 10 2
2.5 43 10 2.5 43 10
S50-PA…Y: The sensor can be fixed by means of the M18x1 threaded OUTPUT LED OUTPUT LED

body through a ∅ 18mm hole, using the specific washer and the 0

Ø4

Ø4
enclosed 24mm nuts (maximum torque of tightening 1.5Nm). 0 20 40 60 80 100 120
Alternatively, the sensor can be mounted through the two housing’s
M18x1

M12x1

M18x1
=

=
M12
INVERSE PROPORTIONALITY (INV)
holes using two screws (M3x22 or longer) and nuts. Amongst the
various possible solutions, we suggest to choose the combination that N°.2 Ø3.8 FIELD LED FIELD LED

offers the best visibility of the signalling LEDs. 34 25

FIELD LED
OUTPUT LED
FIELD LED
OUTPUT LED
mm
22mm nuts, h=8mm, (2Nm maximum tightening torque) are available to
guarantee an improved torque.

S50-MA…Y: The sensor can be fixed by means of the M18x1 threaded

body through a ∅ 18mm hole, using the specific washer and the two TECHNICAL DATA
CH.24 nuts enclosed (22Nm maximum tightening torque).
S50-PA PLASTIC VERSIONS S50-MA METALLIC VERSIONS
Power supply: 18 … 30 Vdc (limit values)
Ripple: 2 Vpp max.
For both plastic version and metallic Current consumption
version are available various orientable 30 mA max.
(output current excluded):
fixing brackets to ease the sensor
Analogue output: 0…10V in tension
positioning (please refer to the
Response time: 3,33 ms DECLARATION OF CONFORMITY
accessories listed in the general
catalogue). Switching frequency: 150 Hz We DATASENSOR S.p.A. declare under our sole responsibility that
The operating distance is measured from Indicators: OUTPUT LED (YELLOW) / FILED LED (RED) these products are conform to the 89/336 CEE, 73/23 CEE Directives
the front surface of the sensor lens. Data retention: non volatile EEPROM memory and successive amendments.
In case of lateral translation, the object Operating temperature: -10 … 55 °C
WARRANTY
must move as indicated in the figure. Storage temperature: -20 … 70 °C DATASENSOR S.p.A. warrants its products to be free from defects.
Electrical shock protection: Class 2 DATASENSOR S.p.A. will repair or replace, free of charge, any product
Operating distance (typical values): 50…100mm found to be defective during the warranty period of 36 months from the
Emission type: RED (630nm) manufacturing date.
Ambient light rejection: according to EN 60947-5-2 This warranty does not cover damage or liability deriving from the
Vibrations: 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6) improper application of DATASENSOR products.
Shock resistance: 11 ms (approx. 30 G) 6 shock for every axis (EN60068-2-27) DATASENSOR S.p.A. Via Lavino 265
Selection: direct or inverse proportionality of the output respect to the object distance 40050 Monte S. Pietro - Bologna - Italy
Housing: PBT Nickel plated brass Tel: +39 051 6765611 Fax: +39 051 6759324
Lenses: PMMA http://www.datasensor.com e-mail: [email protected]
Mechanical protection: IP67 (TYPE 1 ENCLOSURE) DATASENSOR S.p.A. cares for the environment: 100%
Connections: 2 m cable ∅ 4 mm / M12 - 4 pole connector recycled paper.
Weight: 75g. max. cable vers./25g. max. connector vers. 110g. max. cable vers./60g. max. connector vers. DATASENSOR S.p.A. reserves the right to make modifications
and improvements without prior notification.
826001022 Rev.B