CAT I

TOTAL MARKS 30 TIME 1HOUR

Q1: What is free and forced vibration? Describe the degrees of freedom. Derive
the expression of logarithmic decrement of adamped system. 2+2+1|=15
Q2. Mention different types of damping in a mechanical system. Formulate the
expression for the magnification factor in a forced damped system. 5+10=15
 DEPARTMENT OF MECHANICAL ENGINEERING
SUBJECT: INDUSTRIAL ENGINEERING AND MANAGEMENT August, 2024
7th SEMESTER, CLASS TEST - I:
Mark=30
Q1. Design a organization structure for a project
4 departments and 4 sub projects. organization. The project should have at least
(Marks: 10) (CO-1]

Q2. Draw two handed process chart for assembling nut and bolt.
(Marks: 10) (CO-4]
Q3. Identify tçe maintenance practices followed in aprocess industry like refinery.
(Marks: 10) (CO-5)
 APPLIED THERMODYNAMICS-II
PAPER CODE: ME181702
Full Marks: 30 Duration 60 Minutes

1. (CO1|Atwo stages, single acting air compressor compresses air to 20 bar. The air enters the L.P cylinder at
Ibar and 27°cand leaves itat 4.7bar. The air enters the H.P. cylinder at 4.Sbar and 27°c. the size of the L.P
cvlinder is 400 mm diameter and 500 mm stroke. The clearance volume in both cylinder is 4% of therespective
stroke volume. The compressor,runs at 200rpm, taking index of compression and expansion in the two
cylinders as 1.3, estimate (a) The indicated power required to run the compressor; (b) The heat rejected in the
intercooler per minute. (10)

2. |C02] Write Short notes on

() Rotary Compressor
(1) Surging & Choking (10)

3. |CO3] In a regenerative gas turbine power plant air enters the compressor at 1bar, 27 °Cand is compressed
to4 bar. The isentropic efficiency of the compressor is 80%o and the regnerator effectiveness is 90%. Allthe
power developed by the h.p turbine is used to drive the compressor and the I.P turbine provides the net power
output of 97 kW. Each turbine has an isentropic efficiency of 87% and the temperature at inlet to the h.p
turbine is 1200 K. Determine (a) the mass flow rate of air into the compressor, (b) the thermal efficiency, (c)
the temperature of the air at the exit of regenerator. (10)
 CAT 1
Sub: HydraulicMachinery, Sub code: ME181PE11
Full Marks: 30
Time: 1hour
1. MCQ: Choose the rightanswer (1 x 5= 5) the water entered through it?
() VWhich kind of turbines changes the pressure of
a) Reaction turbines
b) Impulse turbines
c) Reactive turbines
d) Kinetic turbines energy of the water.
(i) is the electric power obtained from the
a) Roto dynamic power
b) Thermal power
c) Nuclear power
d) Hydroelectric power electric power generator
(ii) Which energy generated in a turbine is used to run
linked to the turbine shaft?
a) Mechanical Energy
b) Potential Energy
c) Elastic Energy
d) Kinetic Energy
(iv) Hydraulic Machines fall under the category:
a) Pulverizers
b) Kinetic machinery
c) Condensers
d) Roto-dynamic machinery
is defined as ratio between power delivered to runner and
(v)
power supplied at inlet of turbine.
a) Mechanical efficiency
b) Volumetric efficiency
c) Hydraulic efficiency
d) Overall efficiency
2. Deduce the Euler Turbine equation. (5) (CO 1)

3. A Pelton wheel develops 8 MW under a head of 130 m at a speed of 200 rpm. The
following are the particulars of Pelton wheel: coefficient of velocity of the nozzle = 0.98,
speed ratio = 0.46, jet diameter = 1/9 h diameter of wheel, overall efficiency =87%.
Determine: (a) flow required, (b) diameter of wheel, (c) number of jets, (d) number of
buckets. (10) (Co 2)
4. In a hydropower station: Installed capacity = 100 MW, Number of units =4, Rated speed
= 428 rev/min, Rated head = 80 m, Rated flow rate = 6.85 m'/s, type of turbine is
horizontal- Pelton 2jets. Design the Pelton turbine completely and determine the
important efficiencies. (10) (Co 2)
 (ME1810E13]
CAT -I: 2024: SUB]ECT: SOLID WASTE MANAGEMENT
7TH Semester B. Tech.(Mechanical Engineering):Total: 30

centre. Assume the mixed waste to

Q1. (1) DDraw a layout for a mixed waste processing different materials and inert
consist of biodegradable waste, non-biodegradable waste with (10)
waste
(5)
Ql. (ii) How willyou implement Zero Waste philosophy?
quantities of different categories of
Q2. (i) A city is having 10,000 households. Estimate the quartering method for the
municipal solid waste generated from the households. Use
average of 4 member per
estimation. Assume a per capita waste generation of 350gms and
household. Theweight percentage of different items are as follows:

% by weight of each
Item recyclable
Pet bottle 9.43
Glass \30.43
Plastic 15.30
Carton 22.40
Steel/Tin 3.10
Copper/Brass 0.62
Aluminium 0.93
Polythene 5.90
Paper 10.35
Multilayered polythene 1.54

(10)
Q2. (ii) ldentify the different materials based on the numbering (1-7) in plastics products. (5)