cata l o g u e

Ground-to-Air MOBILE
COMMUNICATION

Antennas and
Antenna Line Products
 Who we are
and what we stand for

Kathrein is a leading international specialist for data transmission in buildings, to fibre optic and cable
reliable, high-quality communication technologies. networks and satellite reception technology, to radio
and TV transmission and transmission and reception
We are an innovation and technology leader in today’s systems in vehicles.
connected world. Our ability to provide solutions and sys-
tems enables people all over the world to communicate, As a hidden champion and family-owned enterprise, we
access information and use media, whether at home, at have been working on the technologies of tomorrow since
the office or on the road. We cover a broad spectrum: 1919. We take pride in our dedicated employees and our
from mobile communications, signal enhancement and passion for customers and quality.

Our Solutions

MOBILE INDOOR SAT BROADBAND BROADCAST AUTOMOTIVE

COMMUNICATION

Find out more about us at www.kathrein.com

Catalogue Issue 02/2015

All data published in previous catalogue issues hereby becomes invalid.
We reserve the right to make alterations in accordance with the requirements of our
customers, therefore for binding data please check valid data sheets on our homepage:
www.kathrein.com

Please also see additional information on inside back cover.

Our quality assurance system and our Our products are compliant to the EU
environmental management system apply Directive RoHS as well as to other
to the entire company and are certified RoHS environmentally relevant regulations
by TÜV according to EN ISO 9001 and (e.g. REACH).
EN ISO 14001.
Marker Beacon
4-unit Yagi
74 – 76 MHz

Omnidirectional Antennas
Antennas VHF
Directional Antennas
100 – 160 MHz
Localizer-Monitor Antenna

Filters, Combiners, Couplers,

Filters VHF
Circulators, Decoupling Unit,
100 – 156 MHz
Examples for Customize Combiners

Antennas
Omnidirectional Antennas
Combination VHF/UHF
Multiple-Unit Omnidir. Antenna
118 – 144 / 225 – 400 MHz

Antennas UHF Omnidirectional Antennas

225 – 400 MHz Directional Antennas

Filters, Combiners, Couplers,

Filters UHF
Circulators, Decoupling Unit,
225 – 400 MHz
3-dB Couplers

Monitor Antennas, Glide Path Ant.,

Navigation (ILS, D.M.E.)
Omnidirectional Antennas,
328 – 336 / 960 – 1215 MHz
Directional Antennas

Automatic Dependent
Surveillance - Broadcast
VPol Omnidirectional Antenna
(ADS-B)
1087 – 1093 MHz

Power Splitters
Electrical Accessories
50-Ω Loads

Brackets
Mechanical Accessories
Guy-wire Adapter
Summary of Types

The articles are listed by type number in numerical order.

Type No. Page Type No. Page Type No. Page Type No. Page

711 ... 729 ... 793 ... K6226311 97

711329 20, 21 729803 16, 17 793094 43 K6226317 97
K6226401 97
713 ... 737 ... 800 ... K6226411 97
713316B 82, 83 737398 100 80010228 6 K6226501 97
713645 100 K6226507 97
742 ... 880 ... K6226511 97
714 ... 742363 101 88010002 90, 91 K6226611 96
714747 80, 81 88010003 86, 87 K625531 94, 95
K62563 94, 95
715 ... 780 ... K51 ... K625631 94, 95
715630 78, 79 780231 75 K512631 8, 9 K62573 94, 95
715986 84, 85 780265 47 K625731 94, 95
780266 48 K52 ... K627031 44
716 ... K523031 28, 29
716192 100 784 ... K523131 26, 27 K63 ...
716405 86, 87 78410198 41 K63551 94, 95
78410367 96 K53 ... K635511 94, 95
717 ... 78410470 96 K531831 22, 23 K637011 74
717265 18, 19
717266 18, 19 K55 ... K64 ...
717338 52, 53 791 ... K552031 14, 15 K641231 36, 37
791211 43 K552131 12, 13 K641331 36, 37
718 ... 791525 40 K553131 24, 25 K6421351 34, 35
718215 10, 11 791526 40 K553231 30, 31 K6421361 38, 39
718217 58, 59 791527 40 K6421371 38, 39
791528 46 K61 ...
719 ... 791653 45 K613311 100 K65 ...
719543 18, 19 791857 42 K613321 100 K651311 70
791859 42 K61333 100
722 ... 791988 71 K61334 100 K75 ...
722394 84, 85 K751011 60, 61
792 ... K62 ... K753111 64, 65
723 ... 792008 72 K6226111 96 K753211 66, 67
723141 62, 63 792246 73 K6226201 97 K7540121 62, 63
723904 54, 55 792318 42 K6226207 97 K7540131 62, 63
792329 42 K6226211 97 K7540141 62, 63
727 ... 792330 42 K6226217 97 K7540151 62, 63
727463 16, 17 792504 40 K6226301 97
727728 52, 53 792558 40 K6226307 97

4
 Marker Beacon
74 – 76 MHz
Summary – Marker Beacon
74 – 76 MHz

Height
Type Frequency range Gain Type No. Page
[mm]

Yagi Antenna
4-unit Yagi Antenna 74 – 76 MHz 125° 7 dBi 80010228 1980 6

5
Marker Beacon
74 – 76 MHz

Marker Beacon Antenna 74 –76

Polarization H/V
Half-power Beam Width 125°

4-unit Yagi
Type No. 80010228
Frequency range 74 – 76 MHz
Polarization Horizontal / vertical
Gain 7 dBi
Half-power beam width H-plane: 125°

~ 1980 mm
E-plane: 65°
Impedance 50 Ω
VSWR < 1.4
Max. power 15 W

Material: Hot-dip galvanized steel.

Mounting: Mast: Using the supplied flange 120 x 140 mm.

Walls: Using the mounting kit 711 978.
80010656
Grounding: All metal parts of the antenna including the connector
­delivered mounting kit are DC grounded.

~ 2380 mm

Supplied flange: All dimensions in mm

∅ 14 t = 6 mm

125°

120
80

10
dB

3
100
0
140
Horizontal Pattern

65°
Mechanical specifications

Input N female
Connector position see sketch
10 Weight 22 kg
Wind load 520 N (at 150 km/h)
dB

3 Max. wind velocity 180 km/h

Packing size 2424 x 2118 x 182 mm
0
Height / diameter 1980 / 2380 mm
Vertical Pattern

6
Summary – Antennas VHF
100 – 160 MHz

Antennas VHF
100 – 160 MHz
Height
Type Frequency range Gain Connector Type No. Page
[mm]

Omnidirectional Antennas
Omni 116 – 152 MHz 360° 0 dB N female K512631 430 8, 9

Omni 118 – 137 MHz 360° 0 dB 7-16 female 718215 1050 10, 11

Omni 108 – 152 MHz 360° 0 dB N female K552131 1300 12, 13

Omni 118 – 137 MHz 360° 0 dB N female K552031 1375 14, 15

Omni 118 – 137 MHz 360° 0.5 dB N female 727463 4300 16, 17

Omni 118 – 137 MHz 360° 0.5 dB N female 729803 6000 16, 17

Omni 116 – 152 MHz 360° 3 dB N female 719543 4600 18, 19

Omni 118 – 137 MHz 360° 3.5 dB N female 717265 4000 18, 19

Omni 118 – 137 MHz 360° 4.5 dB N female 717266 6000 18, 19

Localizer-Monitor
Directional Antenna 108 – 118 MHz 112° 5 dB N female 711329 1105 20, 21

Directional Antennas
Directional Antenna 118 – 144 MHz 120° 4 dB N female K531831 1360 22, 23

Directional Antenna 118 – 136 MHz Approx. 240° 5 dB N female K553131 2940 24, 25

Directional Antenna 108 – 137 MHz 76° 7 dB N female K523131 1600 26, 27

Directional Antenna 100 – 160 MHz 62° 8 dB N female K523031 1900 28, 29

Directional Antenna 118 – 144 MHz Approx. 240° 8 dB N female K553231 6040 30, 31

7
 Omnidirectional Antenna
116 – 152 MHz
K512631
Antennas VHF
100 – 160 MHz

Broadband aluminum groundplane-antenna

with stainless steel radials
Type No. K512631
Input N female connector in the antenna base

L1
Connector position Bottom
Frequnecy range 116 – 152 MHz
Bandwidth 36 MHz
VSWR < 1.6 (118 – 144 MHz)
< 2.0 (116 – 152 MHz)
Gain 0 dB (ref. to the half wave dipole) L2
Impedance 50 Ω
Polarization Vertical A
Max. power 60 W (at 50 °C ambient temperature)
Weight 1.5 kg
Wind load 50 N (at 160 km/h)
Max. wind velocity
w/o ice 200 km/h
1/2″ radial ice 135 km/h
Packing size 100 x 85 x 720 mm
Height L1: 430 mm, L2: 700 mm

Material: Radiator: Heavy duty alodined aluminum.

Radials: Stainless steel 8 mm diameter. B
Base: High strength cast aluminum.
All screws and nuts: Stainless steel.

Mounting: The antenna can be mounting by means

of a supplied stainless steel clamp in such
a manner as to permit the cable to be run
either inside a 40 – 54 mm pipe (Fig. A) or
outside a 20 – 54 mm pipe (Fig. B).

Grounding: The antenna is DC grounded by a cross section

of 120 mm2 aluminum.

Scopy of supply: Antenna including mounting hardware.

Radiation Pattern (at mid-band)

78°

10
10
dB

3
dB

0 0

Horizontal Pattern Vertical Pattern

8
Mounting Instruction
Omnidirectional Antenna
K512631

Antennas VHF
100 – 160 MHz
A

A: for pipes of 40 – 54 mm Ø
B: for pipes of 20 – 54 mm Ø

Side mounting on a mast

Brackets for pipes of 55 to 105 mm OD are available for this
mounting mode:

Distance between
pipe and antenna 500 mm 1000 mm
Model No. K61333 K61334

With this mounting mode the standing wave ratio (VSWR)

will be altered somewhat as a factor of clearance and mast
diameter.

9
 Omnidirectional Antenna
118 – 137 MHz
718215
Antennas VHF
100 – 160 MHz

l VHF 4-unit omnidirectional antenna.

l Each unit consists of 4 dipoles round the mast (diameter
200 – 600 mm), which are combined by an integrated power
splitter.

Type No. 718215

Input 7 -16 female
Frequency range 118 – 137 MHz
Gain (ref. λ/2 dipole) 0 dB
VSWR < 1.5
Horizontal radiation pattern:
Deviation from circularity ±1.5 dB
Impedance 50 Ω
Polarisation Vertical
Max. power 400 W (at 50 °C ambient temperature)
Length 1050 mm
Weight 32 kg (for a mast of 500 mm dia.)
Wind load 2.5 kN (at 180 km/h and 4 cm radial ice)

Material: Hot-dip galvanized steel.

Mounting: On a pipe mast with a dia. of 200 – 600 mm.

Please specify exact dia. with order.
The cable length needs to stay unchanged!

Grounding: All metal parts of the antenna including the

­ elivered mounting kit are DC grounded.
d

Scope of supply: Antenna incl. power splitter, cable and mounting

clamps (pipe mast not supplied).

10
Mounting Instruction
Omnidirectional Antenna
718215

Antennas VHF
100 – 160 MHz
approx. 435 mm

approx. 1050 mm

mast diameter > 200 mm,

clamps (supplied):
approx. 920 mm

   clamp range 200 – 400 mm (order-no. 1311484) and

   clamp range 400 – 600 mm (order-no. 1311485)

7-16 female

11
 Omnidirectional Antenna
108 – 152 MHz
K552131
Antennas VHF
100 – 160 MHz

Broadband omnidirectional antenna

in fiberglass radome
Type No. K552131
Input N female connector in the antenna base
Connector position Bottom 120 mm
Frequency range 108 – 152 MHz diameter
Bandwidth 44 MHz
VSWR < 2.0
Gain 0 dB (ref. to the half wave dipole)
Impedance 50 Ω
Polarization Vertical
Max. power 110 W (at 50 °C ambient temperature)
Weight 5.2 kg

≈ 1300 mm
Radome diameter 120 mm
Wind load 120 N (at 160 km/h)
Max. wind velocity 200 km/h (incl. 1/2˝ radial ice)
Packing size 650 x 130 x 100 mm
Height Approx. 1300 mm

Material: Aluminum radiator in fiberglass radome.

Colour: Grey RAL 7001.
Hot-dip galvanized steel bottom.
All screws and nuts: Stainless steel.

Mounting: By means of 4 studs M12 to flange 130 mm dia.

Grounding: The antenna is DC grounded by a cross section

of 26 mm2 aluminum.

Scope of supply: Antenna including 1 neoprene O-ring and

4 mounting studs, each with 2 nuts and 1 washer.

Radiation Pattern (at mid-band)

78°

10
10
dB

3
dB

0 0

Horizontal Pattern Vertical Pattern

12
Mounting Instruction
Omnidirectional Antenna
K552131

Antennas VHF
100 – 160 MHz
130 mm

100 mm

M 12 x 35

flange 130 mm ∅
required metric wrenches:
19 mm

13
 Omnidirectional Antenna
118 – 137 MHz
K552031
Antennas VHF
100 – 160 MHz

Broadband omnidirectional antenna

in fiberglass radome
Type No. K552031
Input N female connector in the antenna base
Connector position Bottom 70 mm
Frequency range 118 – 137 MHz diameter
Bandwidth 19 MHz
VSWR < 2.0
Gain 0 dB (ref. to the half wave dipole)
Impedance 50 Ω
Polarization Vertical
Max. power 1000 W (at 50 °C ambient temperature)
Weight 6.6 kg

1375 mm
Radome diameter 70 mm
Wind load 125 N (at 160 km/h)
Max. wind velocity 200 km/h (incl. 1/2˝ radial ice)
Packing size 1390 x 140 x 140 mm
Height 1375 mm

Material: Hot-dip galvanized steel pipes and mounts.

All screws and nuts: Stainless steel.

Mounting: Flange 130 mm OD for mounting on a flanged

supporting pipe (see mounting instruction).

Grounding: The antenna is DC grounded by a cross section

of 218 mm2 hot-dip galvanized steel.

Scope of supply: Antenna with neoprene O-ring at the flange,

but without mounting hardware.

Radiation Pattern (at mid-band)

78°

10
10
dB

3
dB

0 0

Horizontal Pattern Vertical Pattern

14
Mounting Instruction
Omnidirectional Antenna
K552031

Antennas VHF
100 – 160 MHz

Ø 14 mm

100 mm
130 mm

15
 Omnidirectional Antenna – Multiple-unit
118 – 137 MHz
727463, 729803
Antennas VHF
100 – 160 MHz

2 or 3-element antenna, consisting of several

­independently fed dipoles arranged in line
Type No. 727463 729803
Input N female connector inside of mounting flange
No. of dipoles 2 3
Connector position Bottom
Frequency range 118 – 137 MHz 118 – 137 MHz
Bandwidth 19 MHz 19 MHz
VSWR < 1.8 < 1.8
Gain 0.5 dB 0.5 dB
(ref. to 3 pole)
Attenuation > 27 dB > 25 dB between
­adjacent dipoles
Horizontal radiation pattern Deviation from circularity ±0.3 dB for each dipole
Impedance 50 Ω
Polarization Vertical

Height
Max. power 100 W (at 50 °C ambient temperature)
Weight 33 kg 54 kg
Radome diameter 120 mm 120 mm
Wind load 480 N 730 N
(at 160 km/h)
Max. wind velocity 200 km/h
Height 4300 mm 6000 mm

Material: Radiator: Hot-dip galvanized steel.

Radome: Fiberglas, colour: Brown (RAL 1019).
Flange: Aluminum (OD 320 mm).
Hot-dip ­galvanized steel (OD 265 mm).
All screws and nuts: Stainless steel.

Mounting: Flange 320 mm OD (729803).

Flange 265 mm OD (727463).

Grounding: The antenna is DC grounded by a cross section

of 110 mm2 (727463, 729803) hot-dip galvanized
steel.

Scope of supply: Antenna with neoprene O-ring at the flange, but

without mounting hardware.

Radiation Pattern (at mid-band)

78°

10
10
dB

3
dB

0 0

Horizontal Pattern Vertical Pattern

16
Mounting Instruction
Omnidirectional Antenna
727463, 729803

Antennas VHF
100 – 160 MHz
727463 729803

18 mm
18 mm

225 mm 280 mm

265 mm 320 mm

– Mount the aluminum flange on plane surface only (max. unevenness 0.5 mm)
– Put the O-ring carefully into the circular groove of the flange
– Mounting screws: M16 stainless or hot-dip galvanized steel
(min. strength 5.6 accord. DIN 267)
Max. torque: 50 Nm (screws should be greased with MoS2)
– Put a stainless steel washer between aluminum flange and screw head or nut

17
 Omnidirectional Gain Antenna
116 ... 152 MHz
717265, 717266, 719543
Antennas VHF
100 – 160 MHz

Omnidirectional gain antenna in a fiberglass-tube

Type No. 719543 717265 717266
Input N female connector inside of mounting flange
Connector position Bottom
Frequency range 116 – 152 MHz 118 – 137 MHz 118 – 137 MHz
Bandwidth 36 MHz 19 MHz 19 MHz
VSWR < 2.0 < 1.7 < 1.8
Gain 3.0 dB 3.5 dB 4.5 dB
(ref. to the half wave dipole)
Horizontal radiation pattern ±0.3 dB Devitation from circularity
Impedance 50 Ω
Polarization Vertical
Max. power 200 W (at 50 °C ambient temperature)
Weight 46 kg 33 kg 51 kg
Radome diameter 188 mm 120 mm 120 mm

Height
Wind load 765 N 430 N 700 N
(at 160 km/h)
Max. wind velocity 200 km/h
Height 4600 mm 4000 mm 6000 mm

Material: Radiator: Hot-dip galvanized steel.

Radome: Fiberglas, colour: Brown (RAL 1019).
Flange: Aluminum (OD 320 mm).
Hot-dip galva- nized steel (OD 265 mm).
All screws and nuts: Stainless steel.

Mounting: Flange 320 mm OD (719543).

Flange 265 mm OD (717265, 717266).

Grounding: The antenna is DC grounded by a cross section

of 214 mm2 (719543) and 110 mm2 (717265,
717266) hot-dip galvanized steel.

Scope of supply: Antenna with neoprene O-ring at the flange, but

without mounting hardware.

Radiation Pattern (at mid-band)

34° 31° 21°

10 10 10 10
dB

3
dB

dB

dB

3 3 3

0 0 0 0

Horizontal Pattern Vertical Pattern Vertical Pattern Vertical Pattern

719543 717265 717266

18
Mounting Instruction
Omnidirectional Gain Antenna
717265, 717266, 719543

Antennas VHF
100 – 160 MHz
717265
717266 719543

18 mm
18 mm

225 mm 280 mm

265 mm 320 mm

– Mount the aluminum flange on plane surface only (max. unevenness 0.5 mm)
– Put the O-ring carefully into the circular groove of the flange
– Mounting screws: M16 stainless or hot-dip galvanized steel
(min. strength 5.6 accord. DIN 267)
Max. torque: 50 Nm (screws should be greased with MoS2)
– Put a stainless steel washer between aluminum flange and screw head or nut

19
 Directional Antenna
108 – 118 MHz
711329
Antennas VHF
100 – 160 MHz

Localizer-Monitor

3-element broadband-yagi, 5 dB gain

Type No. 711329
Input N female
Frequency range 108 – 118 MHz 5
47
VSWR < 1.3 �1

Gain 5 dB (ref. to the half wave dipole)

Impedance 50 Ω
Polarization Horizontal
Front-to-back ratio > 15 dB
Max. Power 300 W (at 50 °C ambient temperature) � 1105

Weight 10 kg
Wind load 220 N (at 150 km/h)
Max. wind velocity 150 km/h
Packing size 1525 x 1190 x 92 mm

Material: Hot-dip galvanized steel.

All screws and nuts: Stainless steel.

Mounting: To pipes of 60 – 125 mm diameter by means of

hot-dip galvanized steel clamp, supplied.

Lightning protection: All metal parts of this antenna are DC grounded.

Radiation Pattern (at mid-band)

120°

64°

10
10
dB

3
dB

0 0

in E-plane in H-plane

20
Directional Antenna
108 – 118 MHz
711329

Antennas VHF
100 – 160 MHz
Clamp range
60 – 125 mm
diameter

N female

21
 Directional Antenna
118 – 144 MHz
K531831
Antennas VHF
100 – 160 MHz

3-element broadband-yagi,
4dB gain, hot-dip galvanized steel
Type No. K531831
Input N female connector
in a weather protective housing
directly at the antenna

1360 mm
Frequency range 118 – 144 MHz
VSWR < 1.5
Gain (ref. λ/2 dipole) 4 dB
Impedance 50 Ω
Polarization Usable for horizontal or vertical polarization
Max. Power 160 W (at 50 °C ambient temperature)
Weight 10 kg
Windload 250 N (at 160 km/h)
Max. wind velocity 200 km/h (incl. 1/2˝ radial ice)
Packing size 1500 x 1150 x 90 mm
Antenna height 1360 mm

Material: Hot-dip galvanized steel.

All screws and nuts: Stainless steel.

Mounting: To pipes of 60 – 115 mm OD by means of

hot-dip galvanized steel clamp, supplied.

Grounding: The antenna is DC grounded by a cross section

of 256 mm2 hot-dip galvanized steel.

Scope of supply: Antenna including mounting hardware.

≈ 950
mm

Radiation Pattern (at mid-band)

120°

64°

10
10
dB

3
dB

0 0

in E-plane in H-plane

22
Mounting Instruction
Directional Antenna
K531831

Antennas VHF
100 – 160 MHz
2

1: For vertical polarization

2: For horizontal polarization

23
 Offset Pattern Gain Antenna
118 – 136 MHz
K553131
Antennas VHF
100 – 160 MHz

5 dB offset pattern antenna.

Hot-dip galvanized steel.
Type No. K553131
Input N female connector
inside of the mounting flange
Frequency range 118 – 136 MHz
VSWR < 1.5
Gain (ref. λ/2 dipole) 5 dB
Impedance 50 Ω
Polarization Vertical
Max. Power 280 W (at 50 °C ambient temperature)
Weight 20 kg

2940 mm
Windload 370 N (at 160 km/h)
Max. wind velocity
  w/o ice 200 km/h
   1/2˝ radial ice 150 km/h
370 mm
Packing size 3000 x 510 x 200 mm
Antenna height 2940 mm
Distance dipole/mast 370 mm

Material: Hot-dip galvanized steel.

All screws and nuts: Stainless steel.

Mounting: Flange 190 mm OD for mounting on a flanged

pipe (see rearside).

Grounding: The antenna is DC grounded by a cross-section

of 342 mm2 hot-dip galvanized steel.

Scope of supply: Antenna with neoprene O-ring at the flange,

but without mounting hardware.

Radiation Pattern (at mid-band)

41°
Mast

10 10

3
dB

dB

0 0

Horizontal Pattern Vertical Pattern

24
Mounting Instruction
Offset Pattern Gain Antenna
K553131

Antennas VHF
100 – 160 MHz
ø 18 mm

150 mm
190 mm

25
 Directional Antenna
108 – 137 MHz
K523131
Antennas VHF
100 – 160 MHz

Broadband 7 dB directional antenna,

weatherresistant aluminum.
Type No. K523131
Input N female connector
in a weather protective housing
Frequency range 108 – 137 MHz
VSWR < 1.4
Gain (ref. to λ/2 dipole) 7 dB
Impedance 50 Ω
Polarization Vertical or horizontal
Half-power beam width H-plane: 57°/ E-plane: 76°
Max. power input (CW) 1550 W (at 35 °C ambient temperature)
880 W (at 50 °C ambient temperature)
Weight 12 kg
Lateral thrust 560 N at 160 km/h
Max. wind velocity
  w/o ice 200 km/h
   1/2˝ radial ice 120 km/h
Width/height/depth 1600 / 1600 / 700 mm
Packing size 1620 x 850 x 200 mm

Material: Reflector screen and dipoles: Heavy duty alodined

aluminum.
Mounting clamps: Hot-dip galvanized steel. 700
All screws and nuts: Stainless steel. mm
Scope of supply: Antenna including mounting hardware.

Mounting: To masts of 60 – 115 mm OD.

1600 mm
Lightning protection: All metal parts of the antenna are DC grounded.

1600 mm
Radiation Pattern (at mid-band)

76° 57°

10 10
dB

dB

3 3

0 0

in E-plane in H-plane

26
Mounting Instruction
Directional Antenna
K523131

Antennas VHF
100 – 160 MHz
1

For horizontal polarization

install mounting clamps here

Mounting to pipes
of 60 – 115 mm diameter

27
 Directional Antenna
100 – 160 MHz
K523031
Antennas VHF
100 – 160 MHz

A heavy duty 8 dB gain panel of hot-dip galvanized steel

for use under heavy icing 640 mm

Type No. K523031

Input N female connector
in a weather protective housing
directly at the antenna
Frequency range 100 – 160 MHz

1600 mm
VSWR < 1.3
Gain (ref. λ/2 dipole) 8 dB
Impedance 50 Ω
Polarization Horizontal or vertical
Max. Power 1590 W (at 50 °C ambient temperature)
Weight 35 kg
Windload 1200 N (at 160 km/h)
Max. wind velocity 200 km/h (incl. 1/2˝ radial ice)
Packing size 2000 x 2000 x 850 mm
Height/width/depth 1900 x 1900 x 640 mm

Material: Hot-dip galvanized steel.

All screws and nuts: Stainless steel.
1600 mm
Montage: By means of a pair of hot-dip gavanized steel
clamps K61120 to pipes of 60 – 115 mm OD
or the pair of clamps K61130 to pipes of
115 – 200 mm.

Grounding: All metal parts of the antenna including the

mounting kit are DC grounded.

Scope of supply: Panel without mounting hardware.

Special features: The fiberglass cover of the radiators keeps the

electrical characteristics, even under heavy icing
conditions, nearly constant.

Radiation Pattern (at mid-band)

62° 64°

10 10
dB

dB

3 3

0 0

Horizontal Pattern Vertical Pattern

28
Mounting Instruction
Directional Antenna
K523031

Antennas VHF
100 – 160 MHz
1

ø1
1 7

65
55

55
0 42

25
0
2

1, 2: Pair of clamps K61120 for pipes of 60 – 115 mm OD or pair of clamps K61130

for pipes of 115 – 200 mm OD

Required metric wrenches: 19 mm and 24 mm

29
 Offset Pattern High Gain Antenna
118 – 144 MHz
K553231
Antennas VHF
100 – 160 MHz

8 dB offset pattern antenna.

Hot-dip galvanized steel.
Type No. K553231
Input N female connector
inside of the mounting flange
Frequency range 118 – 144 MHz
VSWR < 1.5
Gain (ref. λ/2 dipole) 8 dB 370 mm
Impedance 50 Ω
Polarization Vertical
Max. Power 220 W (at 50 °C ambient temperature)
Weight 54 kg
Windload 950 N (at 160 km/h)
Max. wind velocity
  w/o ice 170 km/h
   1/2˝ radial ice 135 km/h
Packing size 2 pcs.: 3600 x 510 x 200 mm
   and 3000 x 510 x 200 mm
Antenna height 6040 mm

6040 mm
Distance dipole/mast 370 mm

Material: Hot-dip galvanized steel.

All screws and nuts: Stainless steel.

Mounting: Flange 210 mm OD for mounting on a flanged

supporting pipe (see mounting instruction).

Grounding: The antenna is DC grounded by a cross-section

of 798 mm2 hot-dip galvanized steel.

Scope of supply: Antenna with neoprene O-ring at the flange,

but without mounting hardware.

Radiation Pattern (at mid-band)

24°
Mast

10 10

3
dB

dB

0 0

Horizontal Pattern Vertical Pattern

30
Mounting Instruction
Offset Pattern High Gain Antenna
K553231

Antennas VHF
100 – 160 MHz
required metric wrenches:
19 mm

ø 18 mm

170 mm
210 mm

31
For your notes

32
Summary – Filter VHF
100 – 156 MHz

Frequency range
Type ... tunable bandwidth Type No. Page
– fixed bandwidth

100 – 156 MHz

Band-pass Filter

Filters VHF
Band-pass Filter 1 cavity 118 ... 144 MHz K6421351 34, 35
Band-pass Filter 2 cavities 100 ... 156 MHz K641231 36, 37
Band-pass Filter 3 cavities 100 ... 156 MHz K641331 36, 37

S-P Filter
S-P Filter 1 cavitiy 118 ... 144 MHz K6421361 38, 39
S-P Filter 1 cavitiy 118 ... 144 MHz K6421371 38, 39

Filter Transmitter Combiner

Filter Transmitter Combiner 2 inputs 118 ... 144 MHz 791527 40
Filter Transmitter Combiner 3 inputs 118 ... 144 MHz 791526 40
Filter Transmitter Combiner 4 inputs 118 ... 144 MHz 791525 40
Filter Transmitter Combiner 5 inputs 118 ... 144 MHz 792558 40
Filter Transmitter Combiner 6 inputs 118 ... 144 MHz 792504 40
Filter Transmitter Combiner 2 inputs 118 ... 144 MHz 78410198 41

Filter Receiver Combiner

Filter Receiver Combiner 2 outputs 118 ... 144 MHz 792318 42
Filter Receiver Combiner 3 outputs 118 ... 144 MHz 791857 42
Filter Receiver Combiner 4 outputs 118 ... 144 MHz 791859 42
Filter Receiver Combiner 5 outputs 118 ... 144 MHz 792329 42
Filter Receiver Combiner 6 outputs 118 ... 144 MHz 792330 42
Filter Receiver Combiner 2 outputs 118 ... 144 MHz 793094 43
Filter Receiver Combiner 3 outputs 118 ... 144 MHz 791211 43

Coupler
3-dB Coupler 100 – 150 MHz K627031 44

Circulator
Circulator 118 – 144 MHz 791653 45

Decoupling unit
Decoupling unit 118 – 144 MHz 791528 46

Receiver Multicoupler
Receiver Multicoupler 8 outputs 117.5 – 144 MHz 780265 47
Receiver Multicoupler 16 outputs 117.5 – 144 MHz 780266 48

Examples for customize combiners

Combiner System, 6 channels VHF 49
Combiner System, 20 channels VHF 50

33
 Band-pass Filter
118 ... 144 MHz

The band-pass filter is suitable as receiving

210 mm
or transmitting filter, for one transmitting or

max.
receiving channel.

It can be used:
– to improve the input selectivity of receivers
and amplifiers,
– to increase the isolation of transmitters,
100 – 156 MHz

whose respective antennas are mounted

Filters VHF

close together,
– to suppress noise sidebands and inter-
modulation products,
– as a component to form combiners.

Design and construction:

The band-pass filter is designed as a tempe-
rature stabilized λ/4 coaxial resonator. The
pass band frequency as well as the input and
output coupling are adjustable.

770 mm
Filter characteristics:
Narrow pass band range with low insertion
loss, high stop band attenuation, variable filter
response corresponding to the desired stop
band attenuation.

Combination of several band-pass filters:

Several band-pass filters can be inter­
connected using cables of an electrical length
of λ/4. This causes an increase in the edge
steepness of the filter curve as well as the
bandwidth of the pass band. The individual
filters are tuned to the center frequency of the
complete filter.

Insertion loss of the filter combination =

Sum insertion loss of the individual filters
190

+ cable attenuation of the interconnecting

cables (about 0.1 dB per cable).
mm

Stop band attenuation of the filter

combination =
mm
Sum stop band attenuation of individual filters 190
+ additional stop band attenuation.

If the stop band attenuation of the individual

filters exceeds 10 dB, approximately the
following applies: Technical Data
additional stop band attenuation =
(n – 1) x 5 dB; Type No. K6421351
n = number of individual filters.
Frequency range 118 ... 144 MHz
For special applications band-pass filters can
also be interconnected with S-P filters. Insertion loss 0.5 ... 2 dB, tunable
VSWR < 1.5
Tuning: Impedance 50 Ω
The band-pass filter is tuned to the desired Input power < 200 W
pass band frequency and insertion loss at
Temperature range –30 … +60 °C
the factory. Please specify desired pass band
frequency and insertion loss (curve A, B, C, Connectors N female, silver-plated
D) when ordering. Material Outer conductor: Aluminum
The pass band filter can also be tuned on site Inner conductor: Brass, silver-plated
using the supplied instructions. Installation Free standing or
wall mounting with mounting angles
Attached hardware Filter with 2 mounting angles
and 2 connecting pieces
Weight 13 kg
Packing size 207 mm x 1125 mm x 207 mm
Dimensions (w x h x d) 190 mm x max. 980 mm x 190 mm
(with tuning rod)

34
Band-pass Filter
118 ... 144 MHz
Typical attenuation curves
Tuning examples:

Band-pass Filter
K6421351

100 – 156 MHz

Filters VHF
0
Attenuation/dB

Attenuation/dB

Attenuation/dB
1
1 2
5 3
A
B
4
2
A 5
C
10 6
7
3 8
B 9
10
11
15 4 14
16
C
20
24
-0.2 -0.1 f0 -1.0 -0.8 -0.6 -0.4 -0.2 f0
20

25
A
30
K6421351
35
B

40
C

-5 -4 -3 -2 -1 f0 +1 +2 +3 +4 +5
Frequency/ MHz

Curve Insertion loss

A 0.5 dB
B 1.0 dB
C 2.0 dB

35
 Band-pass Filter
100 ... 156 MHz

The band-pass filter is suitable as receiving 426 mm

or transmitting filter, for one transmitting or
receiving channel.

It can be used:
– to improve the input selectivity of receivers
and amplifiers,

240 m
– to increase the isolation of transmitters,
100 – 156 MHz

whose respective antennas are mounted

Filters VHF

m
close together,
– to suppress noise sidebands and inter-
modulation products,
– as a component to form combiners.

Design and construction:

The band-pass filter consists of two or three 124 mm
high Q capacitively coupled resonators.
The pass band frequency, the coupling be-
tween the resonators as well as the 37
input and output coupling are adjustable. 37 2-cavity band-pass filter mm
mm
Filter characteristics:
Narrow pass band range with low insertion 426 mm
loss, high stop band attenuation, variable
filter response corresponding to the desired
stop band attenuation.

Tuning:
The band-pass filter is tuned to the desired
pass band frequency and insertion loss at
the factory. Please specify desired pass band

360 m
frequency and insertion loss (curve A, B)
when ordering.

m
The band-pass filter can also be tuned on
site using the supplied instructions.

124 mm

3-cavity band-pass filter 37

37
mm mm
Technical Data
Type No. K641231 K641331
Frequency range 100 ... 156 MHz
Insertion loss 1 ... 2 dB, tunable 1.5 ... 2 dB, tunable
1.0 dB 2.0 dB 1.5 dB 2.0 dB
curve A curve B curve A curve B
VSWR < 1.2
Impedance 50 Ω
Input power < 50 W < 25 W
Temperature range –30 ... +60 °C
Temperature coefficient < 18 x 10 –6/ °C
Connector N female
Material Outer conductor and inner conductor:
Brass, silver-plated
Colour Grey
Installation With 4 screws (max. 6 mm diameter)
Weight 12 kg 18 kg
Packing size 614 mm x 195 mm x 314 mm 614 mm x 195 mm x 434 mm
Dimensions (w x h x d) 426 mm x 124 mm x 240 mm 426 mm x 124 mm x 360 mm

36
Band-pass Filter
100 ... 156 MHz
Typical attenuation curves
Tuning examples:

100 – 156 MHz

Filters VHF
2-cavity band-pass filter K641231 3-cavity band-pass filter K641331

Attenuation/dB

Attenuation/dB
Attenuation/dB

Attenuation/dB
2 2

10 10
4 4
A

6 6
B
20 20
8 8
A
B
10 10
30 30
-0.4 -0.2 f0 -0.2 -0.1 f0

40 40

50 50

A
60 60
A
B
70 B 70

-8 -6 -4 -2 f0 -3 -2 -1 f0
Frequency/MHz Frequency/MHz

Insertion
Curve Model Type No.
loss

A 2 cavities 1.0 dB K641231

B 2 cavities 2.0 dB K641231
A 3 cavities 1.5 dB K641331
B 3 cavities 2.0 dB K641331

37
 S-P Filter
118 ... 144 MHz

The S-P filter (Stop-Pass filter) is used to at-

tenuate interfering signals located extremely
close to the operational frequency.

It can be used:
– in the transmission path to suppress

210 mm
max.
side band noise and to attenuate inter­
modulation products at the receiving
100 – 156 MHz

frequencies,
Filters VHF

– in the receiving path to attenuate transmit-

ting frequencies,
– as a component for combiners with very
low frequency spacing.

Design and construction:

The S-P filter is designed as a high Q tempe-
rature stabilized λ/4 coaxial resonator. Using
a special temperature stabilized coupling,
high stop band attenuation can be adjusted

770 mm
very close to the pass band
frequency.

Filter characteristics:
Narrow pass band range with low insertion
loss, high stop band attenuation at the stop
band frequency. Even in case of very small
spacing between the pass band and the stop
band frequency a high stop band attenuation
is achieved, which can not be achieved using
190

standard band-pass filters of the same size.

mm

Combination of several S-P filters:

Several S-P filters can be interconnected by mm
cables with an electrical length of λ/4. 190

Insertion loss of the filter combination =

Sum insertion loss of the individual filters +
cable attenuation of the interconnecting
cables (about 0.1 dB per cable). Stop band
attenuation of the filter combination =
Sum stop band attenuation of the individual
filters + additional stop band attenuation.

If the stop band attenuation of the individual Technical Data

filters exceeds 10 dB, approximately the
following applies:
additional stop band attenuation =
Type No. K6421361 K6421371
Pass frequency Below stop frequency Above stop frequency
(n – 1) x 5 dB;
n = number of individual filters. Frequency range 118 ... 144 MHz
For special applications S-P filters can also Frequency separtion
be interconnected with band-pass filters. Minimum 0.2 MHz
Maximum 5 MHz
Tuning: Insertion loss 0.5 ±0.15 dB
The S-P filter is tuned to the desired pass VSWR < 1.5
band and stop band frequency at the factory. Impedance 50 Ω
Please specify desired pass band and stop
band frequency when ordering. Input power < 200 W
Temperature range –20 … +60 °C
The S-P filter can also be tuned on site using Effect of temperature < 0.2 kHz / °C
the supplied instructions. Connectors N female
Material Outer conductor: Aluminum
Inner conductor: Brass, silver-plated
Installation Free standing or
wall mounting with mounting angles
Attached hardware S-P filter with 2 mounting angles
and 2 connecting pieces
Weight 13 kg
Packing size 207 mm x 1125 mm x 207 mm
Dimensions (w x h x d) 190 mm x max. 980 mm x 190 mm
(with tuning rod)

38
S-P Filter
118 ... 144 MHz
Typical attenuation curves
Tuning examples:

K6421361
Pass frequency below stop frequency
-0.3 -0.1 f0
A 0

Attenuation/dB
B A
C
5

100 – 156 MHz

D
B

Filters VHF
E
F C
G
H
D
10
E
15

dB
-0.2 f0 0.1 F
20
G
25
1
30
2
H
35
3
40
4
45
f0 +0.2 +0.4 +0.6 +0.8 +1.0 +1.2
Frequency/MHz

K6421371
Pass frequency above stop frequency
f0 +0.2
0 A
Attenuation/dB

B
A C
D
5 B E
F
C G
10 H
D
E
15
dB

F -0.1 f0 0.2
20

25
G 1
30
2
35 H
3
40 4
45
-1.2 -1.0 -0.8 -0.6 -0.4 -0.2 f0
Frequency/MHz

Frequency separation
Curve
stop band frequency / pass band frequency

A 0.2 MHz
B 0.3 MHz
C 0.4 MHz
D 0.5 MHz
E 0.6 MHz
F 0.8 MHz
G 1.0 MHz
H 1.2 MHz

39
 Filter Transmitter Combiner
with 2, 3, 4, 5 or 6 inputs
118 ... 144 MHz

The Tx combiner enables several transmitters to be

connected into one common antenna.

The Tx combiner consists of one douple circulator

and one 1-pole bandpass filter per channel. The
outputs of the filters are connected via pre-defined
cable lengths onto a common starpoint. This star-
point then forms the output of the combiner.
100 – 156 MHz
Filters VHF

Tuning:
The bandpasses must be tuned to the individual
operating channels. Upon request this tuning may
be performed at our factory (in this case please
state the operating channels when ordering) or it
may be undertaken on site.

792504

Tx combiner 792504

BP: Band-pass filter

↑: Circulator

Technical Data
The insertion loss and isolation values apply to the minimum frequency spacing.

Type No. Inputs Max. power Dimensions Weight

(CW) 19˝ drawer
Height Depth

791527 2 2 x 100 W 22 hu* / 977 mm 380 mm 42 kg

791526 3 3 x 100 W 22 hu* / 977 mm 380 mm 61 kg
791525 4 4 x 100 W 22 hu* / 977 mm 380 mm 81 kg
792558 5 5 x 100 W 22 hu* / 977 mm 570 mm 103 kg
792504 6 6 x 100 W 22 hu* / 977 mm 570 mm 122 kg
Frequency range 118 ... 144 MHz (tunable)
Min. requency spacing 200 kHz
Insertion loss < 3.5 dB
Isolation > 60 dB
VSWR < 1.25 (at the operating frequency)
Impedance 50 Ω
Temperature range 0 ... +50 °C
Connection N female
Material Outer conductor: Aluminum
Inner conductor: Brass, silver plated
Color Front plate: Grey
* hu = height unit

40
Filter Transmitter Combiner
for narrow frequency spacing
118 ... 144 MHz

The Tx combiner enables two transmitters to be

combined to one common antenna output.

The Tx combiner consists of one douple circulator

and two 1 pole band-pass filters per channel.

The outputs of the filters are connected via pre-

defined cable lengths onto a common starpoint.

100 – 156 MHz

This starpoint then forms the output of the combi-

Filters VHF
ner.

Tuning:
The band-passes must be tuned to the individual
operating channels. Upon request this tuning may
be performed at our factory (in this case please
state the operating channels when ordering) or it
may be undertaken on site.

Technical Data
The insertion loss and isolation values apply to the minimum frequency spacing.

Type No. 78410198

Inputs 2
Frequency range 118 ... 144 MHz (tunable)
Min. frequency spacing 100 kHz
Insertion loss < 5.5 dB
Isolation > 60 dB
VSWR < 1.25
BP: Band-pass filter
Impedance 50 Ω ↑: Circulator
Input power (CW) 2 x 100 W
Temperatur range 0 ... +50 °C
Connectors N female
Material Outer conductor: Aluminum
Inner conductor: Brass, silver plated
Colour of front plate Grey
Weight 68 kg
Dimensions 19˝ drawer
(height: 22 hu* = 977 mm, depth: 380 mm)
* hu = height unit

41
 Filter Receiver Combiner
with 2, 3, 4, 5 or 6 outputs
118 ... 144 MHz

The Rx combiner enables several receivers to be

combined to one common antenna input.

The Rx combiner consists of one 1-pole band-pass

filter per channel.
The inputs of the filters are connected via pre-defi-
ned cable lengths onto a common starpoint.
This starpoint then forms the input of the combiner.
100 – 156 MHz
Filters VHF

Tuning:
The bandpasses must be tuned to the individual
operating channels. Upon request this tuning may
be performed at our factory (in this case please
state the operating channels when ordering) or it
may be undertaken on site.

Input

Starpoint

BP BP BP BP 791859

Output 1 Output 2 Output 3 Output 4

Rx combiner 791859

BP: Band-pass filter

Technical Data
The insertion loss and isolation values apply to the minimum frequency spacing.

Type No. Outputs Dimensions Weight

19˝ drawer
Height Depth

792318 2 22 hu* / 977 mm 190 mm 36 kg

791857 3 22 hu* / 977 mm 380 mm 49 kg
791859 4 22 hu* / 977 mm 380 mm 62 kg
792329 5 22 hu* / 977 mm 570 mm 75 kg
792330 6 22 hu* / 977 mm 570 mm 88 kg
Frequency range 118 ... 144 MHz (tunable)
Min. frequency spacing 200 kHz
Insertion loss ≤ 2.5 dB
Isolation ≥ 18 dB
VSWR < 1.5
Impedance 50 Ω
Temperature range 0 ... +50 °C
Connection N female
Material Outer conductor: Aluminum
Inner conductor: Brass, silver plated
Color Front plate: Grey
* hu = height unit

42
Filter Receiver Combiner
for narrow frequency spacing
118 ... 144 MHz

The Rx combiner enables two receivers to be com-

bined to one common antenna output.

The Rx combiner consists of two 1 pole band-pass

filters per channel.

The band-pass filter is designed as a temperature

stabilized λ/4 coaxial resonator.

100 – 156 MHz

Filters VHF
The intputs of the filters are connected via pre-
defined cable lengths onto a common starpoint.
This starpoint then forms the input of the combiner.

Tuning:
The band-passes must be tuned to the individual
operating channels. Upon request this tuning may
be performed at our factory (in this case please
state the operating channels when ordering) or it
may be undertaken on site.

793094

Technical Data
The insertion loss and isolation values apply to the minimum frequency spacing.

Type No. 793094 791211

Outputs 2 3
Frequency range 118 ... 144 MHz (tunable) 793094
Min. frequency spacing 100 kHz
Insertion loss < 4.5 dB
Isolation > 18 dB
VSWR < 1.25
Impedance 50 Ω
Temperatur range 0 ... +50 °C
Connectors N female
Material Outer conductor: Aluminum
Inner conductor: Brass, silver plated
Colour of front plate Grey
Weight 62 kg 88 kg
Dimensions 19˝ drawer 19˝ drawer
(22 hu* = 977 mm, depth: 380 mm) (22 hu* = 977 mm, depth: 570 mm)
* hu = height unit

791211
BP: Band-pass filter

43
 3-dB Coupler (90° Hybrid)
100 – 150 MHz

The 3-dB coupler can be used:

– as decoupled power splitter with a ratio of 1:1,
– for the decoupled combining of two transmitters
with arbitrarily low frequency spacing (at 3-dB
100 – 156 MHz
Filters VHF

loss),
– for the decoupled combining of two receivers with
arbitrarily low frequency spacing,
– for the decoupled combining of two transmitter/
receiver units, whose integrated duplexers are
within the same frequency range, as a frequency
independent 90° phase shifter,
– as a component to form combiners.

Design and function:

The 3-dB coupler has four ports, two of which are
decoupled from each other.
For example effective power entering into port 1 is
distributed into ports 2 and 3.
Port 4 is decoupled and without power if ports 2 and Typical attenuation 1 ↔ 2 and 1 ↔ 4

Attenuation 1 ↔ 2 / dB
Attenuation 1 ↔ 4 / dB
3 are ideally matched. In practice an absorber of vs frequency
suitable power is to be planned for according to the 1 3
mismatch of ports 2 and 3. 2.5
1↔2
Custom versions: 3.0
On request couplers with a coupling attenuation 1↔3
between 3 dB and 10 dB are available. 3.5
2 4
100 150
Frequency/MHz

Technical Data Attenuation 2 ↔ 3 vs VSWR at port 1

Type No. K627031

Attenuation 2 ↔ 3 / dB

Connectors N female
Frequency range 100 – 150 MHz 25
Attenuation 1 ↔ 2 / 1 ↔ 3 3 ±0.4 dB
Attenuation 2 ↔ 3 See diagram
Directivity > 35 dB
VSWR < 1.06
Impedance 50 Ω 20

Max. power 500 W

Material Brass, silver-plated
Colour Grey
Installation With 2 screws (max. 6 mm diameter)
15
Weight 1.6 kg
Packing size 931 mm x 54 mm x 126 mm
Dimensions (w x h x d) 625 mm x 40 mm x 95 mm 1.0 1.5 2.0
(incl. connectors) VSWR at port 1
(with 50-Ω load at port 4)
Note: VSWR and attenuation are measured when the remaining ports are
­terminated with 50-Ω loads.

44
Circulator
118 – 144 MHz

The circulator can be used:

– to increase the coupling attenuation between trans-
mitters, to reduce intermodulation products,
– to prevent adverse effects to unmatched load impe- 3
dance on amplifier performance.

Function:
The circulator is a non-reciprocal component with

100 – 156 MHz

low insertion loss in the forward direction (1 → 2)

Filters VHF
and high attenuation in the reverse direction (2 → 1).
The impedance at the input (1) of the circulator is cons-
tant and independent of the impedance of the compo-
nents following, since the reflected power at the output 1
(2) is passed to the absorber port (3), which must be
terminated with an absorber.
2
Dimensions of the absorbers:
The absorber at port (3) must be dimensioned to
be able to absorb the maximum power reflected at
output (2).

Technical Data
Type No. 791653
Frequency range 118 – 144 MHz
Insertion loss 1 → 2 < 0.8 dB
Isolation 2 → 1 > 40 dB
VSWR < 1.25
Impedance 50 Ω
Input power (CW) < 120 W
Temperature range 0 ... +50 °C
Connectors N female
Material Brass case, nickel plated
Weight Approx. 1.2 kg
Dimensions (w x h x d) 180 mm x 32 mm x 90 mm (incl. connectors)

45
 Decoupling unit
118 – 144 MHz

This decoupling unit can be used to increase the

isolation between transmitters, if the used antennas
are situated very close together.

The decoupling unit consists of a double circulator

and an absorber.

The impedance at the input of the decoupling unit

100 – 156 MHz
Filters VHF

is constant and is independent of the antenna’s

VSWR. The signal received or reflected by the
antenna is fed to the absorber.

Output
2

25 W

1
Input

Technical Data
Type No. 791528
Frequency range 118 – 144 MHz
Insertion loss 1 Ö 2 < 0.8 dB
0
Isolation > 40 dB 21
VSWR < 1.25
Impedance 50 Ω
Input power < 100 W
Return power < 25 W
Temperature range 0 ... +50 °C
Connectors N female
Installation With 2 screws (max. 4 mm diameter)
8
Weight 1.6 kg 17
Packing size 241 mm x 202 mm x 115 mm
50
Dimensions (w x h x d) See figure

46
Receiver Multicoupler
117.5 – 144 MHz, 8 Outputs

The use of the receiver multicoupler 780265 is ­appropriate

if several receivers are operated ­simultaneously at the
same site. With this receiver ­multicoupler up to 8 receivers
can be connected to one common antenna.
This results in considerable savings for the antenna
system. The low noise figure and the excellent inter­
modulation properties guarantee a high dynamic range Front view
and thereby improved receiving conditions. This is of

100 – 156 MHz

­particular significance in locations where transmitters are

Filters VHF
also operated next to receivers.

The receiver multicoupler consists of:

– a low noise amplifier,
– a power splitter,
– a voltage supply.

The receiver multicoupler has an active redundancy due

to the two amplifier modules in parallel which are located
in the low noise amplifier. This means that the receiver Back view
multicoupler still supplies all ­connected ­receivers even if
one of the amplifier ­modules fails. The signal levels in this
case decrease by approximately 6 dB.
Each amplifier module is designed for operation with its Block diagram receiver multicoupler
own voltage supply of 230 V AC or +11 … +48 V DC.

decoupled out-
distributing puts
network

active redundant
amplifier

Technical Data
Type No. 780265
Number of inputs 1
Number of outputs 8
Frequency range 117.5 – 144 MHz
Gain 3.0 dB ±1.5 dB
Noise figure 4.0 dB +0.5 dB
3rd order intercept point > 23 dBm (typ. 25 dBm)
Isolation > 25 dB (typ. 30 dB) between any two outputs
VSWR
  Input < 1.4 Receiver multicoupler
  Output < 1.4
Impedance 50 Ω
Power supply 230 V +10/–15%, 50 … 60 Hz and/or
+11 … +48 V DC
Power consumption < 9 W (230 V, 50 Hz)
< 20 W (+11 … +48 V DC)
117.5 MHz 144
Temperature range –20 … +50 °C
Connectors N female
Colour Front panel: Grey
Attached hardware Power cable and 4 pin DC-connector
Weight 3.9 kg Receiver Receiver Receiver Receiver Receiver
Packing size Approx. 540 mm x 105 mm x 410 mm
Dimensions (w x h x d) 483 mm x 44 mm x 250 mm, 19˝ drawer 8 receivers
Note: Unused outputs have to be terminated using a 50-Ω load in order to
­comply with the specifications. Example receiver multicoupler
117.5 – 144 MHz

47
 Receiver Multicoupler
117.5 – 144 MHz, 16 Outputs

The use of the receiver multicoupler 780266 is ­appropriate

if several receivers are operated ­simultaneously at the
same site. With this receiver ­multicoupler up to 16 recei-
vers can be connected to one common antenna.
This results in considerable savings for the antenna
system. The low noise figure and the excellent inter­
modulation properties guarantee a high dynamic range
and thereby improved receiving conditions. This is of Front view
100 – 156 MHz

­particular significance in locations where transmitters are

Filters VHF

also operated next to receivers.

The receiver multicoupler consists of:

– a low noise amplifier,
– a power splitter,
– a voltage supply.

The receiver multicoupler has an active redundancy due

to the two amplifier modules in parallel which are located
in the low noise amplifier. This means that the receiver
multicoupler still supplies all connected receivers even if Back view
one of the amplifier modules fails. The signal levels in this
case decrease by approximately 6 dB.
Each amplifier module is designed for operation with its Block diagram receiver multicoupler
own voltage supply of 230 V AC or +11 … +48 V DC.

decoupled out-
distributing puts
network

active redundant
amplifier

Technical Data
Type No. 780266
Number of inputs 1
Number of outputs 16
Frequency range 117.5 – 144 MHz
Gain 1.0 dB ±1.5 dB
Noise figure 4.5 dB ±0.5 dB
3rd order intercept point > 12 dBm (typ. 16 dBm)
Isolation > 25 dB (typ. 30 dB) between any two outputs
VSWR
  Input < 1.4 Receiver multicoupler
  Output < 1.4
Impedance 50 Ω
Power supply 230 V +10/–15%, 50 … 60 Hz and/or
+11 … +48 V DC, minus grounded
Power consumption < 9 W (230 V, 50 Hz)
< 20 W (+11 … +48 V DC)
117.5 MHz 144
Temperature range –20 … +50 °C
Connectors N female
Colour Front panel: Grey
Attached hardware Power cable and 4 pin DC-connector
Weight 5.9 kg Receiver Receiver Receiver Receiver Receiver
Packing size Approx. 540 mm x 115 mm x 460 mm
Dimensions (w x h x d) 483 mm x 88 mm x 250 mm, 19˝ drawer 16 receivers
Note: Unused outputs have to be terminated using a 50-Ω load in order to
­comply with the specifications. Example receiver multicoupler
117.5 – 144 MHz

48
Combiner System
6 channels VHF
Example

Tx antenna Rx antenna

100 – 156 MHz

Filters VHF
appr. 50 dB antennas
coupling attentuation at
6 meters vertical spacing

A B

6 channel 6 channel
Tx filter combiner Rx filter combiner
792504 792330

Tx 1 Tx 2 Tx 3 Tx 4 Tx 5 Tx 6 Rx 1 Rx 2 Rx 3 Rx 4 Rx 5 Rx 6

Frequency range: 118 ... 144 MHz

Input power: < 100 W

Insertion loss: Tx A: < 3.5 dB

B Rx: < 2.5 dB

Isolation: Tx Tx: > 60 dB

Tx Rx: > 65 dB
Rx Rx: > 18 dB

49
 Filters VHF
100 – 156 MHz

50
Tx antenna Tx antenna Rx a n t e n n a
appr. 25 dB appr. 65 dB
antennas coupling attentuation antennas coupling attentuation
at 6 meters horizontal spacing at 1000 meters spacing

Multiple-unit Multiple-unit Multiple-unit

Example

antenna antenna antenna

717280 717587 717587
Tx/Rx Combiner
20 channels VHF

A1 A2 A3 A4 A5 B1 B2

4 channel 4 channel 4 channel 4 channel 4 channel

filter transmitter filter transmitter filter transmitter filter transmitter filter transmitter Rx multicoupler Rx multicoupler
combiner combiner combiner combiner combiner 780266 780265
791525 791525 791525 791525 791525

4x2W
K62261111

Tx 1 Tx 2 Tx 3 Tx 4 Tx 5 Tx 6 Tx 7 Tx 8 Tx 9 Tx 10 Tx 11 Tx12 Tx13 Tx14 Tx15 Tx16 Tx17 Tx18 Tx19 Tx 20 Rx 1 – Rx 16 Rx 17 – Rx 20

Input power: < 100 W

Insertion loss: Tx A: < 3.5 dB Frequency range: 118 ... 137 MHz
B Rx: > 1.5 dB gain

Isolation: Tx Tx: > 60 dB

Tx Rx: > 65 dB
Rx Rx: > 25 dB Note: Rx site is located 1000 meters from Tx site.
Summary – Combination VHF/UHF
118 – 144 MHz / 225 – 400 MHz

Height
Type Frequency range Gain Connector Type No. Page
[mm]

Omni
Omni 118 – 144 / 225 – 400 MHz 360° 0 dB / 1 dB 2x N female 717338 3600 52, 53

Omni 118 – 144 / 225 – 400 MHz 360° 0 dB / 1 dB 2x N female 727728 3600 52, 53

Multiple-Unit Omni

Antennas VHF/UHF
Multiple-Unit Omni 118 – 137 / 225 – 400 MHz 360° 0 dB / 1 dB 4x N female 723904 7000 54, 55

Combination

51
 Omnidirectional Antenna – Multiple-unit
118 – 144 / 225 – 400 MHz
717338, 727728

Omnidirectional 2-unit antenna, consisting of one VHF and

one UHF dipole in common fiberglass-tube
Type No. colour: brown 717338
colour: red/white/red 727728
System VHF UHF
Input N female N female
Frequency range 118 – 144 MHz 225 – 400 MHz
VSWR < 1.8 < 2.0
Gain 0 dB 1 dB
Antennas VHF/UHF

(ref. to the half wave dipole)

Combination

Horizontal radiation pattern: ± 0.3 dB ± 0.3 dB (225 MHz)

Deviation from circularity ±1 dB (400 MHz)
Impedance 50 Ω
Polarization Vertical
Max. power 100 W (at 50 °C ambient temperature)

3600 mm
Decoupling 118 – 144 MHz: > 27 dB
225 – 400 MHz: > 24 dB
Weight 38 kg
Radome diameter 188 mm
Wind load 590 N (at 160 km/h)
Max. wind velocity 241 km/h
Height 3600 mm

Material: Radiator: Hot-dip galvanized steel.

Radome: Fiberglass.
Base: Aluminum.

Mounting: Standard flange 320 mm OD.

Grounding: The antenna is DC grounded by a cross section

of 214 mm2 steel.

Scope of supply: Antenna with neoprene O-ring at the flange,

but without mounting hardware.

52
Mounting Instruction
Omnidirectional Antenna
717338, 727728

Antennas VHF/UHF
Combination
18 mm

280 mm

320 mm

– Mount only on a plane surface with max. unevenness 0.5 mm

– Put the O-ring carefully into the circular groove of the flange
– Mounting screws: M 16 stainless or hot-dip galvanized steel
(min. strength 5.6 accord. DIN 267)
Max. torque: 50 Nm (screws should be greased with MoS2)
– Put a stainless steel washer between aluminum flange and screw head or nut

53
 Multiple-Unit Antenna
118 – 137 MHz / 225 – 400 MHz
723904

Multiple-antenna consisting of 2 VHF and 2 UHF

­omnidirectional antennas
Type No. 723904
System VHF UHF
Input 2 x N female 2 x N female
Connector position Bottom Bottom
Frequency range 118 – 137 MHz 225 – 400 MHz
VSWR < 1.8 < 2.0
Horizontal radiation pattern:
Deviation from circularity < ±0.3 dB < ±1 dB
Antennas VHF/UHF

Gain 0 dB 1 dB
Combination

(ref. to the half wave dipole)

Impedance 50 Ω 50 Ω
Polarization Vertical Vertical
Max. power 100 W 100 W
(at 50 °C ambient temperature)
Decoupling UHF – UHF: > 25 dB
VHF – VHF: > 25 dB
UHF – VHF: > 20 dB
Weight 80 kg
Wind load 900 N (at 160 km/h)
Max. wind velocity 200 km/h
Bending moment (y–y) 2570 Nm (at 160 km/h)
3760 Nm (at 200 km/h)
Height Approx. 7000 mm

Material: Hot-dip galvanized steel in fiberglass radome.

Colour: Red/white/red.
All screws and nuts: Stainless steel.

Mounting: Flange 320 mm diameter.

Grounding: The metal parts of the antenna are DC grounded.

54
Mounting Instruction
Multi-Unit Antenna
723904

Antennas VHF/UHF
Combination
18 mm

280 mm

320 mm

– Mount the aluminum flange on plane surface only (max. unevenness 0.5 mm)
– Put the O-ring carefully into the circular groove of the flange
– Mounting screws: M16 stainless or hot-dip galvanized steel
(min. strength 5.6 accord. DIN 267)
Max. torque: 50 Nm (screws should be greased with MoS2)
– Put a stainless steel washer between aluminum flange and screw head or nut

55
For your notes

56
Summary – Antennas UHF
225 – 400 MHz

Frequency Height
Type Gain Connector Type No. Page
range [mm]

Omnidirectional Antennas
Omni 225 – 400 MHz 360° 0 dB 7-16 female 718217 570 58, 59

Omni 225 – 400 MHz 360° 0.5 dB N female K751011 Approx.1200 60, 61

Omni 225 – 400 MHz 360° 2x 1 dB 2x N female K7540121 2650 62, 63

Omni 225 – 400 MHz 360° 3x 1 dB 3x N female K7540131 3690 62, 63

Omni 225 – 400 MHz 360° 4x 1 dB 4x N female K7540141 4230 62, 63

Omni 225 – 400 MHz 360° 5x 1 dB 5x N female K7540151 5570 62, 63

Omni 225 – 400 MHz 360° 3 dB N female 723141 2650 62, 63

Directional Antennas

Antennas UHF
225 – 400 MHz
Directional Antennas 225 – 400 MHz 180° 5.5 dB N female K753111 1380 64, 65

Directional Antennas 225 – 400 MHz 180° 8 dB N female K753211 2740 66, 67

57
 Omnidirectionl Antenna
225 – 400 MHz
718217

l  dipoles round a mast (diameter 250 – 600 mm),

6
are combined by an integrated power splitter.

Type No. 718217

Input 7-16 female
Frequency range 225 – 400 MHz
VSWR < 2.0
Horizontal radiation pattern:
Deviation from circularity
Mastdiameter 500 mm:
±1.0 dB (225 MHz)
±1.5 dB (325 MHz)
±3.5 dB (400 MHz)
Gain (ref. λ/2 dipole) 0 dB
Impedance 50 Ω
Polarization Vertical
Max. Power 650 W (at 50 °C ambient temperature)
Weight 40 kg (for a mast of 500 mm dia.)
Wind load 3.5 kN (at 180 km/h and 4 cm radial ice)
Antennas UHF
225 – 400 MHz

Max. wind velocity 200 km/h

Material: Hot-dip galvanized steel.

All screws and nuts: Stainless steel.

Mounting: On a pipe mast with a dia. of 250 – 600 mm.

Please spezify exact dia. with order.
The cable lenth needs to stay unchanged!

Grounding: All parts of the antenna including the delivered

mounting kit are DC grounded.

Scope of supply: Antenna incl. power splitter and cables

(pipe mast not supplied).

Radiation Pattern (at mid-band)

225 MHz 310 MHz 400 MHz

10
dB

Vertical Pattern

58
Omnidirectionl Antenna
225 – 400 MHz
718217

Antennas UHF
225 – 400 MHz

59
 Cone Antenna
225 – 400 MHz
K751011

Type No. K751011

Input N female connector
in a weather protective housing
at the end of the support pipe
Frequency range 225 – 400 MHz
VSWR < 1.8
Gain (ref. λ/2 dipole) 0.5 dB
Impedance 50 Ω
Polarization Vertical
Max. Power 290 W (at 50 °C ambient temperature)
Weight 9.5 kg
Windload 160 N (at 160 km/h)
Max. wind velocity 200 km/h (incl. 1/2˝ radial ice)
Packing size 1250 x 520 x 520 mm

Material: Hot-dip galvanized steel.

Antennas UHF
225 – 400 MHz

All screws and nuts: Stainless steel.

Mounting: Parallel mounting at the top of the mast by ­means

of two butt straps (see mounting instruction).

Grounding: The antenna is DC grounded by a cross-section

of 400 mm2 hot-dip galvanized steel.

Scope of supply: Antenna without mounting hardware.

Radiation Pattern (at mid-band)

225 MHz 310 MHz 400 MHz

10
dB

Vertical Pattern

60
Mounting Instruction
Cone Antenna
K751011

Antennas UHF
225 – 400 MHz
60

50

300

25

ø14

61
 Omnidirectional Antenna
225 – 400 MHz
K75401.., 723141

l  ulti-element antenna, consisting of several separately fed

M
dipoles arranged in line.
l Special models of gain antennas with an integrated power
splitter.
Standard models: Multiple-unit antenna

Type No. K7540121 K7540131 K7540141 K7540151

Gain (ref. to the 2 x 1 dB 3 x 1 dB 4 x 1 dB 5 x 1 dB
λ/2 dipole)

Special models I: Omnidirectional gain antenna

Type No. 723141

Gain (ref. to the 3 dB
λ/2 dipole)

Length 2650 mm 3690 mm 4730 mm 5770 mm

Weight 29 kg 37 kg 49 kg 67 kg
Wind load 430 N 590 N 760 N 940 N

Height
at 160 km/h
Bending moment 560 Nm 1070 Nm 1780 Nm 2690 Nm
Antennas UHF
225 – 400 MHz

at 160 km/h (at attachment point)

Radome diameter 188 mm
Max. wind velocity 200 km/h
Frequency range 225 – 400 MHz
Bandwidth 175 MHz
Input Type N female connectors in the antenna base
VSWR < 2.0
Attenuation > 27 dB between adjacent dipoles
Max. input 110 W (at 50 °C ambient temperature)
power (CW)
Polarization Vertical

Material: Radiating elements: Hot-dip galvanized steel.

Base: Weatherproof aluminum.
Radome: Fiberglass, colour: Brown.
Intermal screws and nuts: Stainless steel.

Mounting: Flange 320 mm OD for mounting on a flanged supporting

pipe.

Scope of supply: Antenna with neoprene O-ring at the flange, but without
screws.

Grounding: The antenna is DC grounded by a cross section of 214 mm2

hot-dip galvanized steel.

For standard models

78° (45°)
dB

dB

3 3

0 0

Horizontal Pattern Vertical Pattern

Radiation Pattern 225 MHz 400 MHz

62
Omnidirectional Antenna
225 – 400 MHz
K75401.., 723141

K7540121

Antennas UHF
225 – 400 MHz
18 mm

280 mm

320 mm

– Mount the aluminum flange on plane surface only (max. unevenness 0.5 mm)
– Put the O-ring carefully into the circular groove of the flange
– Mounting screws: M16 stainless or hot-dip galvanized steel
(min. strength 5.6 accord. DIN 267)
Max. torque: 50 Nm (screws should be greased with MoS2)
– Put a stainless steel washer between aluminum flange and screw head or nut

63
 Offset Pattern Gain Antenna
225 – 400 MHz
K753111

5.5 dB offset pattern antenna

Hot-dip galvanized steel
Type No. K753111
Input N female connector
inside of the mounting flange
Frequency range 225 – 400 MHz
VSWR < 1.7
Gain (ref. λ/2 dipole) 5.5 dB
Impedance 50 Ω
Polarization Vertical
Max. Power 260 W (at 50 °C ambient temperature)
Radiation pattern Preferred direction: Mast to radiator.
Weight 18 kg

approx. 1380 mm
Windload 200 N (at 160 km/h)
Max. wind velocity 200 km/h (incl. 1/2˝ radial ice)
Packing size 1450 x 400 x 200 mm
Antenna height Approx. 1380 mm
Distance dipole/mast 250 mm
Antennas UHF
225 – 400 MHz

250 mm
Material: Hot-dip galvanized steel.
All screws and nuts: Stainless steel.

Mounting: Via standard flange 130 mm diameter.

The upper flange is suitable for installation
of an obstruction light.

Grounding: All metal parts of the antenna including

the mounting kit are DC grounded.

Radiation Pattern (at mid-band)

225 MHz 400 MHz

180°

39°/29°

Mast

10 10

3
dB

dB

0 0

Horizontal Pattern Vertical Pattern

64
Mounting Instruction
Offset Pattern Gain Antenna
K753111

130 mm
100 mm

ø 14 mm
ø 39 mm

Antennas UHF
225 – 400 MHz

ø 14 mm

100 mm
130 mm

65
 Offset Pattern High Gain Antenna
225 – 400 MHz
K753211

8 dB offset pattern antenna.

Hot-dip galvanized steel.
Type No. K753211
Input N female connector
inside of the mounting flange
Frequency range 225 – 400 MHz
VSWR < 1.7
Gain (ref. λ/2 dipole) 8 dB
Impedance 50 Ω
Polarization Vertical
Max. Power 300 W (at 50 °C ambient temperature)
250 mm
Weight 40 kg
Windload 450 N (at 160 km/h)
Max. wind velocity 200 km/h (incl. 1/2˝ radial ice)
Packing size 2800 x 400 x 200 mm
Antenna height 2740 mm
Distance dipole/mast 250 mm
Antennas UHF
225 – 400 MHz

Material: Hot-dip galvanized steel.

All screws and nuts: Stainless steel.

Via standard flange 190 mm diameter.

2740 mm
Mounting:
The upper flange is suitable for installation
of an obstruction light.

Grounding: All metal parts of the antenna including

the mounting kit are DC grounded.

Radiation Pattern (at mid-band)

225 MHz 400 MHz

180°

24°/16°

Mast

10 10

3
dB

dB

0 0

Horizontal Pattern Vertical Pattern

66
Mounting Instruction
Offset Pattern High Gain Antenna
K753211

130 mm
100 mm

ø 14 mm
ø 39 mm

Antennas UHF
225 – 400 MHz
required metric wrenches:
19 mm

ø 17 mm

150 mm
190 mm

67
For your notes

68
Summary – Filter UHF
225 – 400 MHz

Frequency range
Type ... tunable bandwidth Type No. Page
– fixed bandwidth

Band-pass Filter 3 cavities 225 ... 400 MHz K651311 70

Transmitter Filter Combiner 2 inputs 225 – 400 MHz 791988 71

Circulator 225 – 400 MHz 792008 72

Decoupling Unit 225 – 400 MHz 792246 73

3-dB Coupler 225 – 400 MHz K637011 74

Receiver Multicoupler 8 outputs 225 – 400 MHz 780231 75

225 – 400 MHz

Filters UHF

69
 Band-pass Filter
225 ... 400 MHz

The band-pass filter is suitable as receiving

or transmitting filter, for one transmitting or
receiving channel.

It can be used:
– to improve the input selectivity of recei-
vers and amplifiers,
– to increase the isolation of transmitters,
whose respective antennas are mounted
close together,
– to suppress noise sidebands and inter-
modulation products,
– as a component to form combiners.

Design and construction:

The band-pass filter consists of three
105

high Q capacitively coupled resonators.

The pass band frequency, the coupling
mm

­be-tween the resonators as well as the

input and output coupling are adjustable.

m
7m
Filter characteristics:
30
Narrow pass band range with low insertion 0m

23
loss, high stop band attenuation, variable m
filter response corresponding to the desired
stop band attenuation.

Tuning:
The band-pass filter is tuned to the desired
pass band frequency and insertion loss at
the factory. Please specify desired pass
band frequency and insertion loss (curve A,
B) when ordering.

The band-pass filter can also be tuned on

225 – 400 MHz
Filters UHF

site using the supplied instructions.

Typical attenuation curves

Tuning example:
3-cavities Band-pass Filter K651311

Attenuation/dB
Attenuation/dB

Technical Data 10
4
A

Type No. K651311 6

Frequency range 225 ... 400 MHz B 20

8
Insertion loss 1 ... 2 dB, tunable
10
1.0 dB 2.0 dB
curve A curve B 30
VSWR < 1.2 -0.8 -0.4 f0

Impedance 50 Ω
Input power < 50 W 40
< 25 W
Temperature range –30 ... +60 °C
Temperature coefficient < 15 x 10 –6/ °C 50
Connector N female A
Material Outer conductor: Aluminum
Inner conductor: Brass, silver-plated 60
Weight 6.5 kg B
Mounting Via 4 screws (max. 6 mm diameter)
Packing size 372 mm x 205 mm x 292 mm 70
Dimensions (w x h x d) 300 mm x 105 mm x 237 mm

-6 -4 -2 f0
Frequency/MHz

70
Filter Transmitter Combiner
with 2 inputs
225 ... 400 MHz

The Tx combiner enables several transmitters

to be combined to one common antenna output.

Special features:
– narrow channel spacing between Tx frequencies
possible,
– low insertion loss,
– high isolation between Tx inputs,
– high filter selectivity at Rx frequencies.

Design and construction:

The Tx combiner consists of one douple circulator
and one 3pole band-pass filter per channel.
The outputs of the filters are connected via pre-­
defined cable lengths onto a common starpoint.
This starpoint then forms the output of the combi-
ner.

Tuning:
The bandpasses must be tuned to the individual
operating channels at our factory (please state the
operating channels when ordering).

Special version
Tx Combiner 4x 100 W

225 – 400 MHz

Filters UHF
Output

Technical Data BP BP
The insertion loss and isolation values apply to the minimum frequency spacing.

Type No. 791988

Frequency range 225 ... 400 MHz (tunable)
Min. frequency spacing 3 MHz
Insertion loss < 3.5 dB
Isolation > 60 dB
VSWR < 1.25
Impedance 50 Ω
Max.power (CW) 2x 100 W
Input 1 Input 2
Temperatur range 0 ... +50 °C
Connectors N female
Inputs 2
Material Outer conductor: Aluminum
Inner conductor: Brass, silver plated
Colour of front plate Grey
Weight 26 kg
Dimensions (h, d) 19˝ drawer
(height: 5 hu* = 445 mm, depth: 600 mm)
* hu = height unit

71
 Circulator
225 – 400 MHz

The circulator can be used:

– to increase the coupling attenuation between trans-
mitters, to reduce intermodulation products,
– to prevent adverse effects to unmatched load impe- 3
dance on amplifier performance.

Function:
The circulator is a non-reciprocal component with
low insertion loss in the forward direction (1 → 2)
and high attenuation in the reverse direction (2 → 1).
The impedance at the input (1) of the circulator is cons-
tant and independent of the impedance of the compo-
nents following, since the reflected power at the output 1
(2) is passed to the absorber port (3), which must be
terminated with an absorber.
2
Dimensions of the absorbers:
The absorber at port (3) must be dimensioned to
be able to absorb the maximum power reflected at
output (2).
225 – 400 MHz
Filters UHF

Technical Data
Type No. 792008
Frequency range 225 – 400 MHz
Insertion loss 1 → 2 < 1.8 dB
Isolation 2 → 1 > 35
VSWR < 1.4 15 W
Impedance 50 Ω
Input power (CW) < 100 W
Temperature range –10 ... +55 °C
Connectors N female
Material Brass case, nickel plated
Weight Approx. 1.2 kg
Dimensions (w x h x d) 180 mm x 32 mm x 90 mm (incl. connectors)

72
Decoupling unit
225 – 400 MHz

This decoupling unit can be used to increase the

isolation between transmitters, if the used antennas
are situated very close together.

The decoupling unit consists of a double circulator

and an absorber.

The impedance at the input of the decoupling unit

is constant and is independent of the antenna’s
VSWR. The signal received or reflected by the
antenna is fed to the absorber.

Output
2

25 W

225 – 400 MHz

Filters UHF
1
Input

Technical Data
Type No. 792246
Frequency range 225 – 400 MHz
Insertion loss 1 Ö 2 < 1.8 dB
0
Isolation > 35 21
VSWR < 1.4
Impedance 50 Ω
Input power < 100 W
Return power < 25 W
Temperature range –10 ... +55 °C
Connectors N female
Installation With 2 screws (max. 4 mm diameter)
8
Weight 1.6 kg 17
Packing size 241 mm x 202 mm x 115 mm
50
Dimensions (w x h x d) See figure

73
 3-dB Coupler (90° Hybrid)
225 – 400 MHz

The 3-dB coupler can be used:

– as decoupled power splitter with a ratio
of 1:1,
– for the decoupled combining of two
transmitters with arbitrarily low frequency
spacing (at 3-dB loss),
– for the decoupled combining of two
receivers with arbitrarily low frequency
spacing,
– for the decoupled combining of two trans-
mitter/receiver units, whose integrated
duplexers are within the same frequency
range, as a frequency independent 90°
phase shifter,
– as a component to form combiners.

Design and function:

The 3-dB coupler has four ports, two of
which are decoupled from each other.
For example effective power entering into
port 1 is distributed into ports 2 and 3.
Port 4 is decoupled and without power
if ports 2 and 3 are ideally matched. In
Typical attenuation 1 ↔ 2 and 1 ↔ 3

Attenuation 1 ↔ 2 / dB
Attenuation 1 ↔ 3 / dB
practice an absorber of suitable power is to vs frequency
be planned for according to the mismatch of 1 3
ports 2 and 3.
2.5
1↔2
Custom versions:
3.0
On request couplers with a coupling
1↔3
attenuation between 3 dB and 10 dB are
3.5
available.
2 4
225 400
Frequency/MHz
225 – 400 MHz
Filters UHF

Technical Data Attenuation 2 ↔ 3 vs VSWR at port 1

Type No. K637011

Attenuation 2 ↔ 3 / dB

Connectors N female
Frequency range 225 – 400 MHz 25
Attenuation 1 ↔ 2 / 1 ↔ 3 3 ±0.4 dB
Attenuation 2 ↔ 3 See diagram
Directivity > 32 dB
VSWR < 1.06
Impedance 50 Ω 20

Max. power 400 W

Material Brass, silver-plated
Colour Grey
Installation With 2 screws (max. 6 mm diameter)
15
Weight 0.9 kg
Dimensions (w x h x d) 312 mm x 40 mm x 95 mm
(incl. connectors)
1.0 1.5 2.0
Note: VSWR and attenuation are measured when the remaining ports are VSWR at port 1
­terminated with 50-Ω loads. (with 50-Ω load at port 4)

74
Receiver Multicoupler
225 – 400 MHz, 8 Outputs

The use of the receiver multicoupler 780231 is ­appropriate

if several receivers are operated ­simultaneously at the
same site. With this receiver ­multicoupler up to 8 receivers
can be connected to one common antenna.
This results in considerable savings for the antenna
system. The low noise figure and the excellent inter­
modulation properties guarantee a high dynamic range Front view
and thereby improved receiving conditions. This is of
­particular significance in locations where transmitters are
also operated next to receivers.

The receiver multicoupler consists of:

– a low noise amplifier,
– a power splitter,
– a voltage supply.

The receiver multicoupler has an active redundancy due

to the two amplifier modules in parallel which are located
in the low noise amplifier. This means that the receiver Back view
multicoupler still supplies all ­connected ­receivers even if
one of the amplifier ­modules fails. The signal levels in this
case decrease by approximately 6 dB.
Each amplifier module is designed for operation with its Block diagram receiver multicoupler
own voltage supply of 230 V ~ or 11 … 48 V =.

decoupled out-
distributing puts
network

active redundant
amplifier

225 – 400 MHz

Filters UHF
Technical Data
Type No. 780231
Number of inputs 1
Number of outputs 8
Frequency range 225 – 400 MHz
Gain 3.0 dB ±1.5 dB
Noise figure 4.0 dB +0.5 dB
3rd order intercept point > 23 dBm (typ. 25 dBm)
Isolation > 25 dB (typ. 30 dB) between any two outputs
VSWR
  Input < 1.4 Receiver multicoupler
  Output < 1.4
Impedance 50 Ω
Power supply 230 V +10/–15%, 50 … 60 Hz and/or
+11 … +48 V = floating
Power consumption < 9 W (230 V, 50 Hz)
< 20 W (11 … 48 V =)
225 MHz 400
Temperature range –20 … +50 °C
Connectors N female
Colour Front panel: Grey
Attached hardware Power cable and 4 pin DC-connector
Weight 3.9 kg Receiver Receiver Receiver Receiver Receiver
Packing size Approx. 540 mm x 105 mm x 410 mm
Dimensions (w x h x d) 483 mm x 44 mm x 250 mm, 19˝ drawer 8 receivers
Note: Unused outputs have to be terminated using a 50-Ω load in order to
­comply with the specifications. Example receiver multicoupler
225 – 400 MHz

75
For your notes

76
Summary – Navigation (ILS, D.M.E.)
328 – 336 / 960 – 1215 MHz

Frequency Height
Type Gain Connector Type No. Page
range [mm]

Monitor Antennas
Monitor Antenna 328 – 336 MHz 140° 4 dB N female 715630 300 mm 78, 79

Glide Path Antennas

Glide Path Antenna 328 – 335.5 MHz 45° 8.5 dB N female 714747 500 mm 80, 81

Glide Path Antenna 328 – 335.5 MHz 25° 12 dB N female 713316B 500 mm 82, 83

Omnidirectional Antennas
D.M.E. Omni 960 – 1215 MHz 360° 9 ±0.5 dBi N female 715986 3030 mm 84, 85

D.M.E. Omni 960 – 1215 MHz 360° 9 ±0.5 dBi N female 722394 2601 mm 84, 85

Directional Antennas
Directional Antenna 960 – 1215 MHz 66° 14 dBd N female 716405 1305 mm 86, 87

Directional Antenna 960 – 1215 MHz 66° 14 dBd N female 88010003 1305 mm 86, 87

328–336 / 960–1215 MHz

Navigation

77
 Monitor-Antenna
328 – 336 MHz
715630

Half wave dipole in front of a reflector screen

in a fiberglass radome
Type No. 715630
Input N female connector in a weather protective
rubber cap directly at the antenna
Connector position Rearside
Frequency range 328 – 336 MHz
VSWR < 1.3
Gain 4 dB (ref. to the half wave dipole)
Impedance 50 Ω
Polarization Horizontal
Max. power 60 W (at 50 °C ambient temperature)
Weight 4.3 kg
Wind load 140 N (at 160 km/h)
Max. wind velocity 200 km/h (incl. 1/2˝ radial ice)
Height/width/depth 300 / 480 / 135 mm

Material: Radiators: Heavy duty aluminum.

Reflector screen: High strength aluminum alloy
sheet. Radome: Impact-resistant fiberglass.
Hot-dip galvanized steel clamps.
All screws and nuts: Stainless steel.

Ice protection: The rugged, impact-resistant fiberglass radome

keeps the electrical characteristics, even under
heaviest icing, nearly constant.

Mounting: To pipes of 60 – 120 mm OD by means of hot-dip

galvanized steel clamp, supplied.

Grounding: The antenna is DC grounded by a cross section

of 304 mm2 aluminum.

Scope of supply: Antenna including mounting hardware.

328–336 / 960–1215 MHz
Navigation

Radiation Pattern (at mid-band)

140°

76°

10 10
dB
dB

3 3

0 0

in E-plane in H-plane

78
Mounting Instruction
Monitor-Antenna
715630

328–336 / 960–1215 MHz

Navigation

79
 Glide Path Antenna
328 – 335.5 MHz
714747
328–336 / 960–1215 MHz
Navigation

80
Mounting Instruction
Glide Path Antenna
714747

910
mm
11
4

32
Mo
nito
ring

190

45
An
ten
na

40
Dimensions in mm

328–336 / 960–1215 MHz

Navigation
Brackets
Type No. Suitable for pipes of Weight
mm ∅ kg

K61325 60 – 115 5.5

81
 Glide Path Antenna
328 – 335.5 MHz
713316B

RF monitor system integrated

Type No. 713316B
Input Type N female connector
Frequency range 328 – 335.5 MHz
VSWR < 1.1
Gain 12 dBd
Impedance 50 Ω
Polarization Horizontal
Half-power beam width H-plane: 80°/ E-plane: 25°
Max. power input (CW) 60 W (at 50 °C ambient temperature)
Max. current (DC) 1 A (between inner and outer conductor)
Weight 19 kg
Max. exp. area 1.0 m2
Lateral thrust 1450 N at 160 km/h
Max. wind velocity 200 km/h (incl. 1/2˝ radial ice)
Width/height/depth 2000 / 500 / 190 mm
Packing size 2100 x 510 x 260 mm

Material: Dipole system: Cast aluminum.

Reflector: Weatherproof aluminum.
Radome: Fiberglass (white).
All screws and nuts: Stainless steel.

Scope of supply: Antenna with two weather protective rubber

caps for the connectors, but without mounting
hardware.

Mounting hardware: Type No. Mast diameter

K61324   60 – 115 mm
K613241 115 – 200 mm

Lightning protection: The antenna is DC grounded including the inner

conductors.
328–336 / 960–1215 MHz
Navigation

Radiation Pattern (at mid-band)

80°
RF monitor system
25°

Input Type N female connector

Frequency range 328 – 335.5 MHz 10 10

VSWR < 1.3

dB

dB

3 3
Coupling attenuation 31 ±1 dB
0 0

Horizontal Pattern Vertical Pattern

82
Mounting Instruction
Glide Path Antenna
713316B

185
0m
m

11
4

32
Mo
nito
ring

An
ten
na
190

45
40

Dimensions in mm

328–336 / 960–1215 MHz

Navigation
Bracket K61324 to pipes of 60 – 115 mm OD
resp. K613241 to pipes of 115 – 245 mm OD

83
 D.M.E. Omnidirectional Gain Antenna
960 – 1215 MHz
715986, 722394
The antenna consists of a number of identical, decoupled half-wave dipoles,
phase-feeding cables and transformer.
Each dipole is mounted onto a central supporting brass tube. The horizontal
pattern is obtained by the circular characteristic of the single dipole, the vertical
pattern varying phase and distance of the single dipoles.
All metal parts are DC grounded and, therefore, widely immune to damage
from lightning. The top of the antenna is fitted with a LED obstruction light
(type no. 715986).
Two antenna monitor probes are located inside the fiberglass tube. All feedlines
and monitor cables descend inside the supporting brass tube.

Type No. 715986 722394

Obstruction light Yes No
Frequency range 960 – 1215 MHz
Bandwidth 255 MHz
VSWR < 1.8 (antenna input)
Gain 9 ±0.5 dBi
Impedance 50 Ω
Horizontal pattern Omnidirectional: Devitation from omni
better ±1.5 dB
Vertical pattern uptilt 3 ±0.5°
Coupling attenuation 25 ±3 dB (antenna/monitor probes)
R. F. peak power 10 kW, modulated as per ICAO recommendation
Polarization Vertical
Temperature range –40 to +60 °C ambient

Material: Dipoles, decoupling elements, supporting tube

and transformer: High quality brass.
Base: Weather-resistant aluminum.
Radome: Fiberglass, colour: Grey.
All screws and nuts: Stainless
steel.

Mounting: To pipes of 60 – 62 mm OD by means of mount­

ing clamps, supplied.

Grounding: The antenna is DC grounded by a cross section

of 98 mm2 brass.

Please note: The antenna 715986 is fitted with a double

LED obstruction light. The obstruction light is
preconfigured as follows: operation with 1 LED
328–336 / 960–1215 MHz

and activated failure detection. In case of a mal-

function of the main LED, the second LED will be
Navigation

activated automatically.

The installation team must be properly qualified

and also be familiar with the relevant national
safety regulations! Non observance of following
standards may damage or destroy the devices
and severe injuries may occur!
Observance of standards: DIN VDE 0100
DIN VDE 0185
DIN VDE 0855

Mechanical
Radiation Pattern (at mid-band) 715986 722394
specifications

Input N female N female

Connector position Bottom Bottom
Wind load 370 N 290 N
(at 150 km/h with 12 mm radial ice)
Max. wind velocity 200 km/h 241 km/h
(incl. 12 mm radial ice)
10 10
Weight 23 kg 20 kg
Radome diameter 86 mm 86 mm
dB

dB

3 3
Length 3024 mm 2657 mm
0 0 Packing size [mm] 3180 x 280 x 300 2780 x 280 x 300

84
 Bottom view
140
715986, 722394

30 80

M 12
Mounting Instruction

∅
62
60

M2 M1

L1 N
DL
D.M.E. Omnidirectional Gain Antenna

5/8" 24G NEF MS 310 2 R-12s-3p

LED
Electr. center ∅86
obstruction
light

956

656 1945

3024

85
Navigation
328–336 / 960–1215 MHz
 Directional Antennas 960 –1215
Vertical Polarization V

The directional antennas 716405 and 88010003 have been specially designed
for DME ground beacons and particularly for DMS-ILS colocation.
The antenna provides a pattern with a cosecant-squared shaping. The antenna
is equipped with two monitoring probes inside.

Type No. 716405 88010003

Inputs (antenna and N female connector
­monitoring probes) (protected by a rubber cap)
Connector positions Rearside
Frequency range 960 – 1215 MHz
VSWR < 1.6 (antenna input)
Gain (ref. λ/2 dipole) 14 dBd
Impedance 50 Ω
Coupling attenuation 25 ±3 dB 20 ±3 dB
(antenna/monitoring probes)
Beam tilt + 4° ±0.5°
R. F. peak power 10 kW; duty cycle 2%
Polarization Vertical
Temperature range –40 °C to +60 °C ambient
Weight 12 kg
Wind load Frontal: 675 N (at 160 km/h)
Lateral: 350 N (at 160 km/h)
Rearside: 650 N (at 160 km/h)
Max. wind velocity 200 km/h (incl. 1/2ʺ radial ice)
Packing size 1420 x 360 x 250 mm
Height/width/depth 1305 / 255 / 150 mm

Material: Radiators: Brass. Reflector screen: High strength

aluminum alloy sheet. Cover: Fiberglass.
Clamps: Hot-dip galvanized steel.
All screws and nuts: Stainless steel

Mounting: To pipes of 40 – 95 mm OD by means of­

­mounting clamps, supplied. Clamps for thicker
masts see second page.

Grounding: The antenna is DC grounded via mounting

328–336 / 960–1215 MHz

clamps. The inner conductors are also DC

grounded.
Navigation

Scope of supply: Antenna including clamps and three weather

­protective rubber caps for the connectors.

Radiation Patterns (at mid-band)

66°

13°

10 10
dB

dB

3 3

0 0

Horizontal Pattern Vertical Pattern

86
Mounting Instructions

Torque:
M8 – 20 Nm
M10 – 25 Nm

M1

M1, M2 = connectors
monitoring system
A = connector RF input

M2

328–336 / 960–1215 MHz

Navigation

Accessories
Weight
Type No. Description Remarks Units per antenna
approx.

738546 1 clamp Mast: 42 – 115 mm diameter 1.1 kg 2 (included in the scope

of supply)
731651 1 clamp Mast: 28 – 60 mm diameter 0.8 kg 2 (order separately if required)
85010002 1 clamp Mast: 110 – 220 mm diameter 2.7 kg 2 (order separately if required)
85010003 1 clamp Mast: 210 – 380 mm diameter 4.8 kg 2 (order separately if required)
85010060 1 offset in combination with the clamps 1.3 kg 2 (order separately if required)
For other special items consult our catalogue.

87
For your notes

88
Summary – Automatic Dependent
Surveillance - Broadcast (ADS-B)
1087 – 1093 MHz

Frequency Height
Type Gain Connector Type No. Page
range [mm]

VPol Omni
VPol Omni 1087 – 1093 MHz 360° 11.5 ±0.5 dBi N female 88010002 3420 90, 91

1087 – 1093 MHz

Collision

89
 VPol Omnidirectional Antenna 1087–1093
Vertical Polarization V

The antenna consists of a number of identical, decoupled half-wave dipoles,

phase-feeding cables and transformer.
Each dipole is mounted onto a central supporting brass tube. The horizontal
pattern is obtained by the circular characteristic of the single dipole, the vertical
pattern varying phase and distance of the single dipoles.
All metal parts are DC grounded and, therefore, widely immune to damage
from lightning.
Two antenna monitor probes are located inside the fiberglass tube. All feedlines
and monitor cables descend inside the supporting brass tube.

VPol Omni 1087–1093 360° 11.5dBi

Type No. 88010002
Frequency range 1087 – 1093 MHz
VSWR < 1.8 (antenna input)
Gain 11.5 ±0.5 dBi
Impedance 50 Ω
Horizontal pattern Omnidirectional: Devitation from omni
better ±1.5 dB
Vertical pattern uptilt 2 ±0.5°
Coupling attenuation 25 ±3 dB (antenna/monitor probes)
R. F. peak power 1 kW, modulated as per ICAO recommendation
Polarization Vertical
Temperature range –55 to +70 °C ambient

Material: Dipoles, decoupling elements, supporting tube

and transformer: High quality brass.
Base: Weather-resistant aluminum.
Radome: Fiberglass, colour: Grey.
All screws and nuts: Stainless steel.

Mounting: To pipes of 60 – 62 mm OD by means of mount­

ing clamps, supplied.

Grounding: The antenna is DC grounded by a cross section

of 98 mm2 brass.
1087 – 1093 MHz
Collision

Mechanical specifications
Radiation Pattern (at mid-band)
Input N female
Connector position Bottom
Wind load 380 N
(at 150 km/h with 12 mm radial ice)
Max. wind velocity 200 km/h
Weight 26 kg
10 10 Radome diameter 86 mm
Height 3480 mm
dB
dB

3 3 Packing size 3580 x 280 x 300 mm

0 0

90
Mounting Instruction
VPol Omnidirectional Antenna
88010002

60

M1
A
ø6
2

M2

M 12

ø 86

2764

3480
Electr. center

1366

1087 – 1093 MHz

Collision
656
140

80

5/8" 24G NEF

30

91
For your notes

92
Summary – Electrical Accessories

Connector Max. power

Type Frequency range Type No. Page
female [Watt]

Power Splitter

2-way Splitter 100 – 156 MHz N K625531 630 94, 95

3-way Splitter 100 – 156 MHz 7-16 K62563 420 94, 95

3-way Splitter 100 – 156 MHz N K625631 420 94, 95

4-way Splitter 100 – 156 MHz 7-16 K62573 430 94, 95

4-way Splitter 100 – 156 MHz N K625731 430 94, 95

2-way Splitter 225 – 400 MHz 7-16 K63551 550 94, 95

2-way Splitter 225 – 400 MHz N K635511 750 94, 95

Max. power
Type Frequency range Connector Type No. Page
[Watt]

50-Ω Load 0.5 0 – 2500 MHz N male K6226611 96

50-Ω Load 1.5 0 – 4000 MHz N male 78410367 96

50-Ω Load 1.5 0 – 4000 MHz 7-16 female 78410470 96

50-Ω Load 2 0 – 2500 MHz N male K6226111 96

50-Ω Load 10 0 – 2500 MHz N female K6226401 97

50-Ω Load 10 0 – 2500 MHz N male K6226411 97

50-Ω Load 25 0 – 2500 MHz N female K6226201 97

50-Ω Load 25 0 – 2500 MHz N male K6226211 97

50-Ω Load 25 0 – 2500 MHz 7-16 female K6226207 97

50-Ω Load 25 0 – 2500 MHz 7-16 male K6226217 97

50-Ω Load 50 0 – 2500 MHz N female K6226301 97

50-Ω Load 50 0 – 2500 MHz N male K6226311 97

50-Ω Load 50 0 – 2500 MHz 7-16 female K6226307 97

50-Ω Load
Accessories

50 0 – 2500 MHz 7-16 male K6226317 97

Electrical

50-Ω Load 100 0 – 1000 MHz N female K6226501 97

50-Ω Load 100 0 – 1000 MHz N male K6226511 97

50-Ω Load 100 0 – 1000 MHz 7-16 female K6226507 97

93
 Power Splitter
100 – 156 MHz / 225 – 400 MHz
K625..., K635...

Power Splitters for low-loss connection of several antennas:

160 mm
0
Frequency For Length L Max. Type No. for female connection 16
range connecting approx. power *) (equipment and antenna side)
MHz ... antennas mm Watt 7-16 N
2 660 630 – K625531

210 mm
110 – 156 3 720 420 K62563 K625631
4 760 430 K62573 K625731
225 – 400 2 870 750 K63551 K635511
*) at 50 °C ambient temperature

Impedance: 50 Ω

Input and output: N female or 7-16 female connector.

L
VSWR: < 1.15

Insertion loss: < 0.05 dB (of the transformation line)

Material: Protective case on the antenna side: Cast aluminum.

Weather protection on the equipment side: UV-resistant
elastomere.
Transformation tube: Aluminum and brass.
All parts are protected with paint.
All screws and nuts: Stainless steel.

Mounting: On tubular masts of 60 – 320 mm by means of stainless

steel tightening band 1020 x 20 x 1 mm, supplied.
Transformers with a total length of more than 700 mm are
delivered with a supporting clamp.

Example of 4-way antenna transformer

Ant.1 Ant.2 Ant.3 Ant.4

K K K K

K: 50 Ω-cables
of the same
electrical length
Accessories
Electrical

Equipment

94
Mounting Instruction
Power Splitter
K625..., K635...

1 2

3 4

Accessories
Electrical

95
 Load
50 Ω

50-Ω loads are suited as absorbers for small and medium

power.

They are used:

– as termination for transmitters or amplifiers used for testing,
measuring or tuning,
– as termination for circulators, directional couplers, hybrid ring
junctions and decoupled power splitters.

Special features of the loads are:

– very low VSWR within a wide frequency range,
– high stability and RF shielding due to the closed aluminum
construction,
– arbitrary installation position because of convectional cooling,
– 50 W and 100 W models can be installed on front or rear
panels of electrical equipment for heat dissipation.

0.5 Watt *)
Type No. K6226611
Connector N male
Frequency range 0 – 2500 MHz
VSWR 0 – 1000 MHz < 1.08
1000 – 2000 MHz < 1.15
2000 – 2500 MHz < 1.20
Application Indoor
Weight 40 g
Packing size 90 mm x 60 mm x 25 mm K6226611
Dimensions 33 mm / 21 mm diameter

1.5 Watt *)
Type No. 78410367 78410470
Connector 7-16 male 7-16 female
Frequency range 0 – 4000 MHz
VSWR 0 – 2000 MHz < 1.10
2000 – 4000 MHz < 1.30
IP rating IP65
Application Outdoor
Weight 120 g
Packing size Approx. 50 mm x 90 mm x 100 mm 78410367
Dimensions 40 mm / 32 mm diameter 42 mm / 29 mm diameter

2 Watt *)
Type No. K6226111
Connector N male
Frequency range 0 – 2500 MHz
Accessories
Electrical

VSWR 0 – 1000 MHz < 1.08

1000 – 2000 MHz < 1.15
2000 – 2500 MHz < 1.20
Application Indoor
Weight 40 g
Packing size 90 mm x 60 mm x 25 mm K6226111
Dimensions 30 mm / 21 mm diameter

96
Load
50 Ω

10 Watt *)
Type No. K6226401 K6226411
Connector N female N male
Frequency range 0 – 2500 MHz
VSWR 0 – 1000 MHz < 1.08
1000 – 2000 MHz < 1.15
2000 – 2200 MHz < 1.20
2200 – 2500 MHz < 1.25
Application Indoor
Weight Approx. 250 g
Packing size 50 mm x 90 mm x 100 mm K6226401
Dimensions in mm (w x h x d) 40 x 82 x 77 40 x 82 x 85
(incl. connector) (incl. connector)

25 Watt *)
Type No. K6226201 K6226211 K6226207 K6226217
Connector N female N male 7-16 female 7-16 male
Frequency range 0 – 2500 MHz
VSWR 0 – 1000 MHz < 1.08
1000 – 2000 MHz < 1.15
2200 – 2500 MHz < 1.20
Application Indoor
Weight Approx. 500 g
Packing size 50 mm x 100 mm x 135 mm
Dimensions in mm (w x h x d) 35 x 94 x 113 35 x 94 x 121 35 x 94 x 125 35 x 94 x 124 K6226201
(incl. connector) (incl. connector) (incl. connector) (incl. connector)

50 Watt *)
Type No. K6226301 K6226311 K6226307 K6226317
Connector N female N male 7-16 female 7-16 male
Frequency range 0 – 2500 MHz
VSWR 0 – 1000 MHz < 1.08
1000 – 2000 MHz < 1.15
2200 – 2500 MHz < 1.20
Application Indoor
Weight Approx. 800 g
Packing size 80 mm x 95 mm x 145 mm
Dimensions in mm (w x h x d) 67 x 90 x 130 67 x 90 x 138 67 x 90 x 134 67 x 90 x 133 K6226301
(incl. connector) (incl. connector) (incl. connector) (incl. connector)

100 Watt *)
Type No. K6226501 K6226511 K6226507
Connector N female N male 7-16 female
Frequency range 0 – 1000 MHz
Accessories
Electrical

VSWR 0 – 1000 MHz < 1.08

Application Indoor
Weight Approx. 2.4 kg
Packing size 130 mm x 195 mm x 180 mm
Dimensions in mm (w x h 114 x 153 x 156 114 x 161 x 156 114 x 170 x 156
x d) (including connector) (including connector) (including connector)
K6226501
*) Rated power at 40 °C ambient temperature. The max. power rating increases or decreases with falling or
rising ambient temperature.

97
For your notes

98
Summary – Mechanical Accessories

Side mounting brackets for Omnidirectional Antennas

Type Type No. Distance to mast Mast diameter Page

Bracket K61333 500 mm 55 – 105 mm 100

Bracket 716192 500 mm 105 – 265 mm 100

Bracket K61334 1000 mm 55 – 105 mm 100

Bracket 713645 1000 mm 105 – 265 mm 100

Bracket K613311 125 – 680 mm 55 – 105 mm 100

Bracket K613321 125 – 680 mm 55 – 105 mm 100

Bracket 737398 100 – 240 mm 40 – 105 mm 100

Guy-wire adapter

Type Type No. Page

Guy-wire adapter 742363 101

Accessories
Mechanical

99
 Accessories
Stand-off Brackets

When mounted to the tip of a mast, the antennas described in this catalogue radiate horizontally in
a circular fashion. However, they can also be mounted laterally to a mast by using an extension
bracket. Depending on the spacing and the mast diameter, various types of radiation patterns can be
achieved.

515 mm
Bracket with fixed spacing
eter
pipe diam m
2 .6 m
Type No. K61333 716192 K61334 713645 44.5 x
3
Weight 2 kg 7 kg 3.2 kg 8.5 kg K 61 33
Distance A: 500 mm 1000 mm
Suitable for antennas with a 215 N (at 150 km/h) 85 N (at 150 km/h)
maximum wind load of
1015 mm

95
Suitable for antennas with mounting kit to pipe masts of 20 – 54 mm
diameter.
Attachment By means of mounting kit (supplied) to pipes of
eter
pipe diam m
diameter:
4
55 mm – 105 mm – 55 mm – 105 mm – K 61 33 2 .6 m
105 mm 265 mm 105 mm 265 mm 44 .5 x
Material Hot-dip galvanized steel.
Wind load 36 N (at 150 km/h) 60 N (at 150 km/h)

A: 125 … 680 mm
D: 450 mm
Bracket with adjustable spacing A
A
Implementation Stand-off Double stand off
fig. A fig. B fig. C D

Type No. K613311 K613321 737398

Weight 6.6 kg 13.7 kg 6 kg

Distance A:
min. 125 mm 100 mm
max. 680 mm 240 mm
Suitable for antennas with mounting kit to pipe masts of
20 – 54 mm 30 – 90 mm 50 – 94 mm
diameter diameter diameter
Attachment By means of mounting kit (supplied) to pipes of
55 mm – 105 mm 40 – 105 mm
diameter diameter
Material Hot-dip galvanized steel.
Wind load 45 N (at 150 100 N (at 150 65 N (at 150
km/h) km/h) km/h)

Double Bracket
740 mm 245 mm

125 to 100 to
680 mm 240 mm
125 to Pipe 40 x 40 mm L 30 x 4
680 mm 48.3 x 2.6 mm
(100 mm length) 2 2
free length Pipe Pipe
65 mm 76.1 x 2.6 mm 70 x 4 mm
free length free length
1 180 mm 1 250 mm
40 x 40 mm
40 x 40 mm L 30 x 4
740 mm
Accessories
Mechanical

fig. A fig. B fig. C

100
Guy-wire adapter
742363

Suitable for omnidirectional antenna serie

K75401 ...

Description:
• Offers additional rigging for 4 guy-wires on an omni­
directional antenna at critical sites.
• Allows simple mounting on already installed antennas.
• Guy-wires are not included in the scope of supply.

Pre-tightening:
• Evenly pre-tighten each of the two pairs of opposite
faced guy-wires in several stages.
• Follow any instruction given by the guy-wire manu­
facturer.

45°
Note: max.
• Close schackle-screw after mounting the guy-wire.
• Use only non-conductive and water repelling material
for the guy-wires.
• Don’t mount any additional metallic part within radia-
ting ­vicinity of the antenna.
∅ 195 mm

Weight Approx. 1.2 kg

Guy-wire force at max. windload Max. 3 kN
Tensioning force 0.4 kN
Guy-wire angle deviation, horizontal Max. 30°
Guy-wire angle deviation, vertical Max. 45°

Top view

max. 30°
Accessories
Mechanical

101
For your notes

102
Please note
As a result of more stringent legal regulations and judgements regarding product liability, we
are obliged to point out certain risks that may arise when products are used under extraordi-
nary ­operating conditions. The mechanical design is based on the environmental conditions as
­stipulated in ETS 300 019-1-4. Wind loads are ­calculated according to ­DIN 1055-4.

The antennas may be used at locations where the anticipated peak wind velocity or gust wind
speed lies within the m
­ aximum wind speed listed in the datasheet. We warrant the mechani-
cal ­safety and electrical functionality under such conditions. The wind speeds are defined in
­accordance with the DIN, EN or TIA standards. This warranty makes ­allowance for the partial
safety factors specified in those standards.

Extraordinary ­operating conditions, such as heavy icing or exceptional ­dynamic stress (e.g.
strain caused by oscillating support structures), may result in the ­breakage of an ­antenna or
even cause it to fall to the ground. These facts must be ­considered during the site planning
process. The details given in our data sheets have to be ­followed carefully when ­installing
the antennas and accessories.
­­ Site planning and installation must be carried out by qualified
and ­experienced staff. All relevant national s­ afety regulations must be upheld and respected.
­Incorrect site planning, faulty installation, as well as ­interfering ­surroundings on site, may lead
to deviations in the ­electrical parameters compared to those ­specified in the ­respective data
sheets.

Subsidiaries/Affiliates
An actual list of Kathrein’s International Representatives can be found on our homepage:
www.kathrein.com

For technical information, orders, catalogues or CD-ROM,

please contact: [email protected]

© KATHREIN-Werke KG
 99812377/PDF/0215/VMWI | Technical data subject to changes.

KATHREIN-Werke KG
Anton-Kathrein-Straße 1-3
D-83022 Rosenheim, GERMANY
Phone +49 (0) 80 31 1 84-0
Fax +49 (0) 80 31 1 84-8 20
www.kathrein.com | [email protected]