Scribd
Upload
11 views

395-lava-fast-cnc_en

Fixing agent

Uploaded by

Awais Imran
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
11 views

395-lava-fast-cnc_en

Fixing agent

Uploaded by

Awais Imran
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Product Information Process Auxiliaries

Lava® Fast CNC

Formaldehyde-free cationic fixing agent

Function Improves wet fastness properties of cellulosic fibers, dyed and printed
with substantive and reactive dyestuffs, as well as of dyed and printed
WO and silk fibers

- improves washfastness of cellulosic fibers, dyed and printed with


Properties
direct dyes
- improves the wet fastness of dyed and printed WO and silk fibers
- prevents migration of substantive dyes and reactive dyestuff
hydrolysates
- protects reactive dyeings and printings against hydrolysis and
thermocracking during processing and use
- free of formaldehyde and epi chloro hydrin compounds
- negligible influence on shade and light fastness
- good compatibility with non-ionic and cationic products
- does not impair handle and sewability

Chemical Characteristics Quaternary ammonium compound

Technical Data Appearance: colorless to slightly yellow, clear, liquid


pH: approx. 6 (10% solution in dist. water)
Density (20°C): approx. 1.0 g/cm³
Viscosity (20°C): approx. 10 mPa.s
Ionicity: cationic
Dilution procedure: in cold water
Shelf life: in originally sealed drums about one year
Stability: stable to acids, alkalis, electrolytes in usual
concentrations and to hard water, incompatible
with anionic products.

Do not store product above + 25°C, product can become useless

Store product cool but not below + 3°C

Lava Fast CNC - 2018/04 Page 1 of 3


Application

Lava Fast CNC improves considerably the fastness to water,


perspiration and ironing. Also the wash fastness of natural and
regenerated cellulosic fibres, dyed and printed with direct dyes are
improved.

Lava Fast CNC prevents a deterioration of wet fastness properties


caused by reactive dyestuff hydrolysates.

In addition, Lava Fast CNC prevents migration of substantive dyes and


reactive dyestuff hydrolysates during the drying process and protects
reactive dyeings and printings against hydrolysis and thermocracking
during processing and use.

Lava Fast CNC is very suitable for improving the wet fastness properties
of dyed and printed WO and silk fibers, it is free of formaldehyde and
epihalogen hydrin compounds, the influence on shade and light fastness
is negligible.

Lava Fast CNC shows a good compatibility with non-ionic and cationic
products. Precipitations will, however, occur with anionic products.

An aftertreatment with Lava Fast CNC will not noticeably impair handle
and sewability.

Dyeing/Printing

In order to optimize fastness properties, the well rinsed, resp. soaped


goods should be aftertreated as follows:

Exhaust method

Aftertreatment of CEL

with direct dyes


0.5 - 1.5 % for pale to medium shades
1.5 - 3% for medium to dark shades

with reactive dyes

0.5 - 1.0 % for pale to medium shades


1.0 - 2.0 % for medium to dark shades

pH 5 - 6, 20 - 30 min 40°C.

In the case of one-bath softening with cationic products, a two-step


process should be applied: at first the cationic softener is added and
then, after 5 - 10 min and at the same temperature, Lava Fast CNC.

Lava Fast CNC - 2018/04 Page 2 of 3


Aftertreatment of WO and silk

0.5 - 1.5 % (1.5 - 3%)


for pale to medium shades (for Superwash-WO)
1.5 - 3 % (3 - 5%)
for medium to dark shades (for Superwash-WO)

At first you should treat the goods for 10 min, at pH 7 - 8, at 20 - 30°C,


then heat up the bath to 40 - 50°C within 10 min, leave dwelling for
approx. 5 min, drain and rinse cold shortly.

The above stated for CO dyeing is also applicable for the one-bath two
step method with Lava Fast CNC and a cationic softener.

Padding

Dyeing of CEL, WO and silk (dry in wet)

Depending on depth of shade: 10.0 - 30.0 g/l


Pad temperature: 20 - 30°C
Drying

Stripping of faulty dyeings

If aftertreated goods are to be redyed, leveled out or stripped, it is at first


necessary to remove Lava Fast CNC according to the following method:
3.0 ml/l formic acid 85% and
3.0g/l Sera Sperse M-IS Liq (liquid, anionic dispersing agent)
30 min at 90°C.
Subsequently, rinse thoroughly warm and cold. 2.0 g/l Sera Sperse M-IS
Liq are also recommended as "leveling agent" in the subsequent
overdyeing recipe.
Finishing
Lava Fast CNC can be used as additive to finishes in order to improve
the wet fastness properties of direct dyes and to reduce color bleeding.
Care should, however, be taken regarding the compatibility of finishes
with Lava Fast CNC (preliminary trials).
Depending on type of dyestuff, the usual concentrations are 10.0 - 30.0
g/l.

DyStar Kimya Sanayi ve Ticaret Ltd. Sti This information and our technical advice - whether verbal, in writing or by
Mecidiye Mah.Cenap Sahabettin Sok.No:24 way of trials - are given in good faith but without warranty, and this also
34718, Kosuyolu / Kadikoy applies where proprietary rights of third parties are involved. Our advice
Istanbul - Turkey does not release you from the obligation to check its validity and to test our
products as to their suitability for the intended processes and uses. The
Telephone +90 216 544 15 00
application, use and processing of our products and the products
Fax(sales) +90 216 339 90 48 manufactured by you on the basis of our technical advice are beyon d our
Fax (marketing) +90 216 339 90 63 control and, therefore, entirely your own responsibility. Our products are
[email protected] sold in accordance with our General Conditions of Sale and Delivery .
www.DyStar.com

Lava Fast CNC - 2018/04 Page 3 of 3

You might also like