Freak Athlete

Hyper Pro Assembly Guide

Important Notice

The written instruction manual is

meant to be a supplement to the Hyper Pro
Assembly video and Getting Started Video.
Go to
Freakathlete.co/pages/getting-started
for full video instructions.

It is critical to follow the full Assembly Video

and the Getting Started video for your own
safety.
Freak Athlete
Hyper Pro Assembly Guide

Hyper Pro
Full Assembly

Hyper Pro
Getting Started
 Freak Athlete
Hyper Pro Assembly Guide
What’s Included
Bolts Washers, Nuts, & Other Tools

● 5x M10x75 Bolts ● 21x M10 Washers ● 2x Hex Wrenches

● 3x M10x60 Bolts ● 8x M10 Nuts ● 1x Allen Wrench
● 5x M10x25 Bolts ● 2x Ankle Support End Cap
● 4x M10x45 Bolts ● 1x Pull Pin
● 2x Red Adjustment Knobs ● 6x M10 Large Washers
● 2x Plastic Spacers
For video assembly, go to FreakAthlete.co/HyperGuide
Make sure all screws are fully tightened during assembly.

Hyper Pro Assembly Parts

● Main Frame ● Vertical Storage Bar

● Rear Base ● Black Rod ● Nordic Pad
● Front U Base ● Top Ankle Roller ● Nordic Pad Frame
● Hip Thrust Support ● Back Extension Frame
● Footplate ● 2x Back Extension Pads
Pre-assembly preparation 1: Tighten all Pre-Installed Bolts on Main Frame Hardware & Parts

1. IMPORTANT: Tighten all of the pre-assembled bolts to maximize stability. Circled ● 19mm Wrench (provided)
below. They may already feel tight, but make sure you go through all of them!

2.You can use your own 19mm wrench if you have one available.

Pre-assembly preparation: Tighten all Pre-Installed Bolts on Main Frame

 Step 1: Rear Base Assembly Hardware & Parts

1. You can use your own 19mm wrench if you have one available. ● 19mm Wrench (provided)

● Main Frame
● Rear Base

Parts needed
Hex Head Bolt M10*75 Bolts Qty: 2

Washers (M10 ) Qty:4

Hex Head Nut(M10) Qty: 2

1.A. Pull out the red knob

and pull the inside tube
until you see the window
and No.12 at the top as
shown.

1.B. Pull out the white knob

then pull the Hyper Pro until
you hear the green knob
clicks.

1.C.Lift the back of the

Hyper Pro until you hear the
blue knob clicks.
 Step 1: Rear Base Assembly Hardware & Parts

PRO-TIPS: ● 19mm Wrench (provided)

1. Always make sure the feet and the wheel are facing down when installing.
2. Always use the open-ended of the wrench on the inside and close-ended side on the
outside. ● Main Frame
● Rear Base

1.D. Lift the Hyper Pro

upright until its leaning by
the front base and square
tube.

1.E. Slide the Rear Base to 1.F. Put the bolts from the
1.G. Use the wrenches to
the back of the Hyper Pro bottom and put the washer
fully tighten the bolts and
(Make sure the feet and and nut on the other end
nuts (Use the open-ended
wheels are facing down). then hand tight (repeat the
side on the inside and the
process for both) .
close-ended side to the
outside).
 Step 2: Foot Plate and Vertical Storage Bar Assembly Hardware & Parts

1. You can use your own 19mm wrench if you have one available. ● 19mm Wrench (provided)

● Foot Plate
● Vertical Storage Bar

Step 2: Foot Plate and Vertical Storage Bar Assembly

Parts needed
Hex Head Bolt M10*25 Bolts Qty: 3
2.A. Bring the machine down
to this position.

Washers (M10 ) Qty:6

Hex Head Nut(M10) Qty: 3

2.B. Install the knob faces

the back of the machine,.

2.C. Line up the bottom 2

holes of the foot plate to the
holes at the back of the
machine.

2.D. Take the bolts and put

it through the holes, put nut
at the bottom bolt to hand
tighten.
2.E. Put the Vertical Storage
Bar in this configuration.
 Step 2: Foot Plate and Vertical Storage Bar Assembly

2.F. Put through another 2.G. Put though washer and

bolt on the top hole and nut and top bolt and nut on
align the vertical Storage the middle bolt afterwards
Bar. then hand tighten.

2.H. Fully tighten bolts and

nuts using wrenches.
 Step 3 Front U-Base Assembly Hardware & Parts
PRO-TIPS:
● 19mm Wrench (provided)
1. Make sure that the feet of the Rear base and Front U Base are facing down before
connecting to the Main Frame.
● Front-U-base

Step 3: Front U-BaseAssembly

Parts needed
3.A. Put the Hyper Pro in
Hex Head Bolt M10*75 Bolts Qty: 2 Vertical Storage mode.

Washers (M10 ) Qty: 4

Hex Head Nut(M10) Qty: 2

3.B. Slide through the front

U-Base to the front of the
Hyper Pro (make sure the
feet are facing down).

3.C. Put the bolts going

through the bottom to
upward direction then hand
tighten by the nuts on the
other end.

3.D. Once they're hand tightened, take your wrenches

and fully tighten them down.
 Step 4: Hip Thrust Attachment Assembly Hardware & Parts
Step 3 Front U-Base Assembly Hardware & Parts
PRO-TIPS: ● 19mm Wrench (provided)
1. Refer to the image below for the positions and alignment of holes in this step. ● 19mm Wrench (provided)
2. Do not over tighten this step.
●Hip
● Back Extension Frame
Thrust

Parts needed
Hex Head Bolt M10*75 Bolts Qty: 1

Washers (M10 ) Qty: 2

4.A. Put the machine flat on
the ground

Hex Head Nut(M10) Qty: 1

Pullpin(10) Qty: 1

4.B. Put the Hip Thrust

attachment to the machine
(make sure the hole line up
based on the image shown)
then put the bolt through.

4.C. Put the washer and nut on the other end

and hand tighten. Important: DO NOT OVER
TIGTHEN THIS STEP. Just tighten until the
bolts is sticking out a little bit.

4.D. Put the hitch pin on the

middle hole for the storage
mode.
 Step 5: Back Extension Frame Assembly Hardware & Parts

● 19mm Wrench (provided)

● Back Extension Frame

Parts needed
Hex Head Bolt M10*60 Bolts Qty: 1

Washers (M10 ) Qty: 2

5.A. Put the Back Extension

Hex Head Nut(M10) Qty: 1 Frame to the machine. Align the
bolt of the Back Extension Frame
to the hole on the front tube of
5.B. Push through the Back Extension Frame until the the machine,.
bolt sticks out, put on the washer and the nut then hand
tighten. Once done, fully tighten using wrench.

5.B. Put the bolt on the middle hole then washer and the
nut on the other side then hand tighten. Once done, fully
tighten using wrenches.
 Step 6: Back Extension Pad Assembly Hardware & Parts
Step 3 Front U-Base Assembly Hardware & Parts
● 2x M10*25 Bolts
PRO-TIPS: ● 2x Ankle Support End Caps
1. Use hand tight only in this step. ● Allen Key

● Back extension Pad

● 2x Back Extension Pads

Parts needed

Plastic Spacer Qty: 2 Hex Head bolt (M10*60) Qty: 2

Large Washer (M10) Qty: 4 Knob Qty: 2

6.A. Put the Plastic Spacer on the 6.B. Align the bottom of the Pads
bottom holes as shown in the to the Plastic Spacer then bolts
image and washer at the bottom,
afterwards hand tight.

6.C. Put the Knob and washer

together. From the bottom, find
the other hole of the Pads then
hand tight. Repeat the process
for both.
 Step 7: Nordic Pad Assembly Hardware & Parts
PRO-TIPS:
● 19mm Wrench (provided)
1. The Nordic Pad frame should be within the boundary of the Nordic Pad.

● Nordic Pad
● Nordic Pad Frame

Parts needed
Hex Head Bolt M10*45 Bolts Qty: 4
7.A. Put the Nordic Pad upside-down.

Washer (M10) Qty: 4

7.B. Align the Nordic Pad Frame with the

holes on the Nordic Pad. Make the
orientation based on the image shown.

7.C. Put on the bolts and washers through

the holes and hand tight them. Fully tight
afterwards using wrench.
 Step 7: Nordic Pad Assembly Hardware & Parts
PRO-TIPS: ● 19mm Wrench (provided)
1. The Nordic Pad frame should be within the boundary of the Nordic Pad.
2. Assembled Nordic Pad is having a short and long end. Make sure the short end is
always facing back. ● Nordic Pad
● Nordic Pad Frame

7.D. Put the Nordic Pad Assy to the Hyper

Pro.

7.D. The extrude of the Nordic Pad Frame

must line up with the window of the
machine. Once inserted twist the knob
clockwise to tighten.
 Step 8: Bottom Ankle Roller Assembly Hardware & Parts
PRO-TIPS: ● 19mm Wrench (provided)
1. Make sure that the longer end of the black rod goes into the hole of the machine. ●Allen Key M6
2. Use the allen key to eliminate wobble on the black rod upon insertion.
● Bottom ankle roller
● Black rod
● 2x Large washers

8.A. Put the black rod to the hole on the

machine. Make the longer end pass thru
the holes and the shorter end must be on
the other side away from the machine.

Longer-end

Shorter-end

8.B. Take your allen key and go

underneath and tighten bolt to remove
any wobble.

8.C. Put the ankle rollers

and slide them on.

8.D. Put the large washer

and bolt in the hole and
hand tighten. Repeat the
process. Then fully tighten
using wrench.
 Step 9: Top Ankle Roller Assembly Hardware & Parts
PRO-TIPS:
1. Congratulations! You are now fully assembled.

● Top ankle roller

9. Slide through the Top Ankle Roller to

the machine as shown in the image.
Ensure all knobs are tightened when in use to ensure
stability.

To learn how to use your Hyper Pro, go to

FreakAthlete.co/HyperGuide