Scribd
Upload
4 views

Assignment 2_Quiz_1_-_SY2023-2024

Uploaded by

Leonard Abarra
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
4 views

Assignment 2_Quiz_1_-_SY2023-2024

Uploaded by

Leonard Abarra
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Technological University of the Philippines

College of Engineering
Civil Engineering Department
Quiz #1 in Mechanics of Deformable Bodies
Name: __________________________________ Date: __________________________
Section: _________________________________ Instructor: Engr. Christian A. Arbalate

2. Segment AB of the bar is a tube with an outer


Part 1: Problem Solving. Show your complete solution. Round-
diameter of 1.5 in. and an inner diameter of 1.25 in.
off only on the final answer to the nearest 3 decimal places.
Segment BC is a solid rod of diameter 0.75 in.
Erasures are not allowed on the final answer:
Determine the maximum force applied if the allowable
1. The1000-kg uniform bar AB is suspended from two cables AC normal stress in segment AB = 210 ksi and in segment
and BD; each with cross-sectional area 400 mm2. Find the BC = 165 ksi.
magnitude P and location x of the largest additional vertical
force that can be applied to the bar. The stresses in AC and BD
are limited to 100 MPa and 50 MPa, respectively.

P = __________________________ (10pts)

3. The figure shows a roof truss and the detail of the


connection at joint H. Members HB and HC are angle
sections 75mm x 75mm with the thicknesses shown in
the figure. The working stresses are 80 MPa for shear
in the rivets and 140 MPa for bearing stress due to the
P = _____________________________ (5pts) rivets. If the number of rivets is limited to 5pcs each
for both members, what is the required diameter of
X = _____________________________ (5pts)
the rivets to fasten the following members to the
gusset plate?

1. Link AC is made of a steel with a 65-ksi ultimate normal stress


and has a ¼ x ½ -in uniform rectangular cross section. It is
connected to a support at A and to member BCD at C by 3/8 -
inch diameter pins, while member BCD is connected to its
support at B by 5/16-in diameter pin. All of the pins are made
of steel with a 25-ksi ultimate shearing stress and are in single
shear. Determine the largest load P that can be applied at D.
(Answer should be in kips).

d = __________________________ (10pts)
P = ______________________________ (20pts)
Max. Normal Stress = ___________________ (10pts)
6. The joint is fastened together using two bolts. If the
4. The circular punch B exerts a force of P on the top of the plate
thickness of all plates is 6mm, determine the required
A . Determine the diameter of the smallest hole that can be
diameter of the bolts if the allowable shearing stress is
punched if the allowable shearing strength is limited to 100
140 MPa, bearing stress is 165 MPa, and tensile stress
MPa and the compressive stress is limited to 150 MPa.
is 190 MPa.

d = ____________________________ (10pts)

d = _____________________________ (10pts)

5. The tank shown in the figure is fabricated from a 7.5mm


steel plate. Calculate the maximum longitudinal and
circumferential stress caused by an internal pressure of 240
MPa. All dimensions are in millimeters. (Answer should be
in MPa)

𝜎𝑇 = ________________________ (10𝑝𝑡𝑠)

𝜎𝐿 = ________________________ (10𝑝𝑡𝑠)

You might also like