OPERATION MANUAL

Description: Multi-Function Gauge Part Number: 34200-96L1*

Applications: DF9.9B, DF15A, DF20A, DF25A, DF30A (Serial No. 510001-)
DF40A, DF50A, DF50AV, DF60A, DF60AV (Serial No. 510001-)
DF70A, DF80A, DF90A, DF100A, DF115A, DF140A (Serial No. 510001-)
DF150, DF175, DF200A, DF200AP (Serial No. 510001-)
DF200, DF225, DF250, DF250AP, DF300AP (Serial No. 510001-)
DF150AP, DF175AP (Serial No. 710001-)
DF350A (Serial No. 810001-)

CONTENTS Ref. Description Q’ty

1 GAUGE ASSEMBLY 1
2 WEATHER COVER 1
3 MOUNTING NUT 1
4 SEAL RING 1
5 OPERATION MANUAL 1

No. 34212-96L12 TK 1
INTRO- Thank you very much for purchasing a SUZUKI Genuine
DUCTION Multi-Function Gauge.

[Request to Customers]
• Store this operation manual in a place where it will not be lost or
damaged. Always carry this manual with you when the operation is
performed and keep this manual close at hand so that you can read
it anytime you need it.
• If you transfer this product, give this operation manual to the new
owner.

 WARNING / CAUTION / NOTICE / NOTE

IMPORTANT Please read this manual and follow its instructions carefully.
To emphasize special information, the symbol  and the words
WARNING, CAUTION, NOTICE and NOTE have special meanings.
These special meanings are applied except when laws or regulations
require the signal words to be used with different meanings. Pay spe-
cial attention to the messages highlighted by these signal words.

 WARNING
Indicates a potential hazard that could result in death or
serious injury.

 CAUTION
Indicates a potential hazard that could result in minor or
moderate injury.

NOTICE
Indicates a potential hazard that could result in damage to the
motor or boat.

NOTE:
Indicates special information to make maintenance easier or
instructions clearer.

• This manual shall not be reproduced, whether in part or in full,

without permission.
• Please note that some part of the product may differ from the
contents in the instructions due to specification changes etc.
• If you have any question, find a problem or have a missing part,
contact your authorized SUZUKI Marine Dealer where you
purchased this product.

2
 In “Safety Precautions”, important precautions are described to
SAFETY
prevent danger to the operator of this gauge or other persons, or
PRE-
damage to the gauge or boat.
CAUT-
IONS Precautions for Handling The Gauge Assembly
 WARNING
Do not disassemble or modify the gauge, otherwise you may
get an electric shock, or even the cause of a fire or injury.
Ask for repairs from the authorized SUZUKI Marine Dealer.

 CAUTION
• Use navigation information, such as Distance and Fuel
Consumption indicated on this gauge as a general reference
only.
When exact navigation information is required, use nautical
charts and dedicated navigation instruments.

• Do not operate this gauge while steering the boat or you might
cause a maritime accident.
When using this gauge while the boat is stopped, check
around the boat to be sure it is safe.

• Do not use the power source other than the specified one.
Doing so might cause heating, inflammation or failure.

NOTICE
• Before installation, take care not to splash water on the back
side of the gauge.
After installation, it is still only water resistant and not
completely waterproof if completely submerged in water.
Take care not to dip this gauge in water.

• Do not to apply excessive force to the display face for it may

be damaged if it is exposed to such force.

• To clean the display face use a piece of soft cloth and lightly
wiping the display face.

3
 Contents
Page

1. Function 5

2. Gauge Screen 6 - 13

2-1 Main Information 7 - 11

(1) Engine Speed Display Screen 7

(2) Speed / Fuel Display Screen 8

(3) Fuel Display Screen 9

(4) All Items Display Screen 10

(5) Troll Mode 11

2-2 Sub Information 12 - 13

3. Menu Screen Operation 14 - 24

3-1 Illumination 15

3-2 Diagnosis 16 - 18

3-3 Display 19 - 20

3-4 Device List 21

3-5 Initial Setting 22 - 24

(1) Unit 23

(2) Time 24

4. Alarm 25 - 26

5. Gauge Screen List 27

6. Specifications 28

4
1. Function
Locations

Main Information
(→ P7)

Sub Information
(→ P12)

Function of Each Button

・Gauge screen ・Menu screen

Change to the previous

① MENU button Change to the menu screen / Gauge screen
a) Change to Sub Information
b) Press and hold either of the
buttons
② buttons Move the cursor
( → P13 Reset the display value)
c) *Press and hold both buttons
( → P17 Data Output)
a) Change to Main Information
③ Set button b) Press and hold button Proceed / Confirm
( → P15 Day or Night)

*All items Display Screen only. ( → P6)

5
2. Gauge Screen

• The following figures show the ・MENU button operation :

display screen and the operation ・SET button operation :
flow. ・ buttons operation :

1. Engine Speed 2. Speed/Fuel 3. Fuel Display 4. All Items

Display Screen Display Screen Screen Display Screen
Analog Analog Analog

Analog / Digital

Digital Digital Digital

Analog or digital display may be selected for Item 1,2 and 4.

Sub Information will be displayed for Item 1,2 and 3.

• Menu Screen

→ P14 Menu Screen Operation

6
2-1. Main Information

(1) Engine Speed Display Screen

[Analog] • Display information

1 Engine speed
2 Clock ( → P22 Initial Setting)
3 Trim position
4 Shift position Forward Neutral Reverse

with
Shift
Position
Sensor
without
[Digital]

5 Sub Information
( → P12 Sub Information)
( → P22 Initial Setting)
6 Caution alarm icon
( → P25 Alarm)
7 Engine position

[Caution message]
8 Caution message
( → P25 Alarm)

7
 (2) Speed / Fuel Display Screen

[Analog] • Display information

1 Speed ( → P22 Initial Setting)

2 Clock ( → P22 Initial Setting)
3 Remaining fuel volume
Indicates the total remaining fuel
volume of the connected tank.
4 Sub Information
( → P12 Sub Information)
( → P22 Initial Setting)

[Digital]
5 Caution alarm icon
( → P25 Alarm)
6 a) GROUND: Ground speed
b) WATER: Water speed

[Caution message]
7 Caution message
( → P25 Alarm)

8
(3) Fuel Display Screen

• Display information

1 Remaining fuel volume (Tank 1)

2 Remaining fuel volume (Tank 2)
3 Sub Information
( → P12 Sub Information)
( → P22 Initial Setting)

4 Remaining fuel volume (Tank 3)

Remaining fuel volume (Tank 4)
*In case of single engine, you can set
up dual tank.
In case of multiple engines, you can
set up quadruple tank.

5 Caution message
( → P25 Alarm)
6 Caution alarm icon
( → P25 Alarm)

9
 (4) All Items Display Screen

[Analog] • Display information

1 Engine speed
2 a) GROUND: Ground speed
b) WATER: Water speed
3 Speed ( → P22 Initial Setting)
4 Total instantaneous fuel flow
( → P22 Initial Setting)
5 Clock ( → P22 Initial Setting)
6 Cooling water temperature
7 Shift position Forward Neutral Reverse

[Digital] with
Shift
Position
Sensor
without

8 Trim position
9 Remaining fuel volume
Indicates the total remaining fuel
volume of the connected tank.

[Caution message]
0 Engine position
A Caution message
( → P25 Alarm)
B Caution alarm icon
( → P25 Alarm)

10
(5) Troll Mode

When the troll mode of the outboard motor is set to ON, the display of the
"Engine speed display" and "All items display" change to an exclusive troll
mode digital display screen.
On the gauge screen, "TROLL" will be indicated.
*Please refer to Owner’s Manual for operating the Troll Mode.

• Engine Speed Display Screen • All Items Display Screen

• Speed / Fuel Display Screen

[Analog] [Digital]

• Fuel Display Screen

11
2-2. Sub Information

• The following figures below show the ・MENU button operation :

display screens and the operation ・SET button operation :
flow. ( → P22 Initial Setting) ・ buttons operation :

Total operating hours Instantaneous fuel flow Total fuel used

Trip time Total instantaneous Latitude / Longitude

fuel flow

Trip distance Instantaneous fuel

economy

Battery voltage / Cooling Average fuel economy

water temperature

12
• The detail is as follows.
Types of Sub Information
Display screen Item Description

The total operating hours from brand-new engine are

Total operating hours
displayed.

This screen indicates the trip time since it was reset

Trip time
last time.

This screen indicates the trip distance since it was

reset last time.
Trip distance
*Separate GPS module or water speed sensor is
required.
Battery voltage /
The cooling water temperature and battery voltage are
Cooling water
displayed.
temperature

Instantaneous fuel This screen indicates the instantaneous fuel flow of

flow each outboard motor.

Total instantaneous This screen indicates the instantaneous total fuel flow
fuel flow of all outboard motor.

This screen indicates the total instantaneous fuel

Instantaneous fuel economy of all outboard motors installed.
economy *Separate GPS module or water speed sensor is
required.
This screen indicates the total average fuel economy
Average fuel of all outboard motors installed.
economy *Separate GPS module or water speed sensor is
required.

This screen indicates the total fuel used of all outboard

Total fuel used
motors installed.

The latitude and longitude of current boat position are

Latitude / Longitude displayed.
*Separate GPS module is necessary.

• Reset the display value

The display value of the Trip time, Trip distance, Average fuel economy and
total fuel used can be reset by press and hold the or button until a
buzzer sound is heard, except menu screen.
(Display values other than those displayed will also be reset at the same time.)

13
3. Menu Screen Operation

• By pressing the MENU button the ・MENU button operation :

display will change to the MENU ・SET button operation :
screen. ・ buttons operation :

Illumination

→ P15 Illumination

Version information
Diagnosis of the software

→ P16 Diagnosis

Display

→ P19 Display

Device List

→ P21 Device List

Initial Setting

→ P22 Initial Setting

14
3-1. Illumination

• Configures the illumination setting ・MENU button operation :

and day / night setting. ・SET button operation :
・ buttons operation :

Brightness The Brightness can

be adjusted in 10
steps.

Day or Night You can select

“Daytime display” or
“Nighttime display” by
press and hold the
SET button, except
for menu screen.

Daytime Nighttime

Sync You can Synchronize

the brightness setting
and the Day or Night
setting of gauges
when the Sync is ON.

15
3-2. Diagnosis

1 Current Code ・MENU button operation :

Display the activated alarm. ・SET button operation :
・ buttons operation :

Current Code

P25 Alarm

Data Output

P17 Data Output

P18 Data Output

16
2 Data Output ・MENU button operation :
• Acquire the engine information, ・SET button operation :
then record and readout the data ・ buttons operation :
with SUZUKI Diagnostic System
Mobile.

Create Data
Acquire the engine information, then, convert to QR code
and record the data.

When the All Items Display Screen is selected,

you can create the QR code by press and hold
both buttons simultaneously.

Processing Error

Caution message (→ P25 Alarm)

If your smart phone could not scan the QR code(s), please try the followings.
a) Adjust the Brightness of the multi-function gauge.
b) Shut off the direct sunlight from the multi-function gauge.

[QR code is registered trademark of DENSO WAVE INCORPORATED.]

17
 ・MENU button operation :
・SET button operation :
・ buttons operation :

Log
Readout the recorded data.

Display the time of the data acquired from

the GPS module.

Display “DATA **” when could not acquire the

time of the data from the GPS module.

Caution message (→ P25 Alarm)

*Be able to store 15 set QR codes at maximum.

The oldest data shall be deleted automatically one by one.

18
3-3. Display

• Configures the settings of the Gauge ・MENU button operation :

screen. ・SET button operation :
・ buttons operation :
Selection Item
Analog : Analog display
Digital : Digital display
OFF : Selected display is skipped.
(Select at least one.)

Engine Speed Display

Analog display Digital display

OFF

Speed/Fuel Display
Analog display Digital display

OFF

Fuel Display

ON OFF

All Items Display

Analog display Digital display

OFF

19
 • Display example of the gauge ・MENU button operation :
screen ・SET button operation :
・ buttons operation :

Example

Pattern
Engine Speed Display : Digital
Speed/Fuel Display : Digital
Fuel Display : ON
All Item Display : Digital

Engine Speed Display Speed/Fuel Display Fuel Display All Items Display

Pattern
Engine Speed Display : Digital
Speed/Fuel Display : OFF
Fuel Display : OFF
All Item Display : Digital

Engine Speed Display Speed/Fuel Display Fuel Display All Items Display

SKIP SKIP

20
3-4. Device List
・MENU button operation :
• Display the information of the
・SET button operation :
connected device.
・ buttons operation :

Display the multi-function gauge serial

number.

Display the name and the serial

number of the connected device(s).

21
3-5. Initial Setting

The settings related to the following items are configured in Initial Setting.
• Unit : Unit setting
• Time : Time setting
Only for Dealer
• Position : Gauge position, Engine position, Engine serial No settings
• Sensor Setting : Sensor setting
• Tank : Tank setting

NOTICE
• Position, Sensor Setting and Tank are used by the dealer during the initial
setting.
• If the setting is changed, the current information may not be displayed any
more.

Some of the items in Initial Setting may be important during the initial setting.
A confirmation screen to draw your attention will be displayed.

・MENU button operation :

・SET button operation :
・ buttons operation :

Menu screen

Unit

P23 Unit

Time

P24 Time

22
 (1) Unit

• Setting for the following units. ・MENU button operation :

・SET button operation :
・ buttons operation :

Distance unit
Kilometers Miles

Nautical miles

Fuel Quantity unit

Liters Gallons (US)

Gallons (IMP)

Speed scale unit

LOW HIGH

LOW HIGH
Display scale Display scale
80 km/h 130 km/h
50 mph 80 mph
50 KNOTS 80 KNOTS

Fuel economy unit

Distance/Quantity Quantity/Distance

Liters/100km

 CAUTION
Select units of measurement which you will prefer and recognize.
Selecting units you do not recognize may cause judgment errors.

23
 (2) Time

• Setting for the time indication. ・MENU button operation :

The range can cover from ・SET button operation :
-12:00 to +14:00. ・ buttons operation :

Clock display ON /OFF

ON OFF

12-hour display or 24-hour display

12 h 24 h

Time difference with UTC (Universal Time Coordinated)

If the gauge is not connected to a GPS module, "--:--" will be displayed.

Press the or button briefly to change the time by 15 minutes.
If you press and hold the or button, the time will be changed in 15
minute units continuously.

24
4. Alarm
If an alarm occurs, the gauge screen will display the caution message and the
caution alarm icon immediately.
The caution message clears when any of the buttons are pressed on the gauge.
However, the caution alarm icon is displayed until eliminating the cause.
The buzzer sound also stops when the cause is eliminated.
Example: Low battery voltage (All Items Display Screen)

Caution message

Caution alarm icon

•List of Caution message

Caution
Caution message Description
alarm icon
This system is activated when the battery voltage deficiency which
could impair your motor’s performance occurs. Adopt the appropriate
*1 measure according to the Owner’s Manual.
If abnormal conditions exist in any sensor signal being input to the
control unit, the self-diagnostic system warns of the abnormal condition.
*1 *2 Adopt the appropriate measure according to the Owner’s Manual.
This system operates when the engine lubricating oil pressure drops
below the correct level. Adopt the appropriate measure according to the
*1 Owner’s Manual.
This system is activated when the cylinder wall temperature is too high
due to insufficient water cooling. Adopt the appropriate measure
*1 according to the Owner’s Manual.
This engine is equipped with an integral fuel filter / water separator and
associated alert system. Adopt the appropriate measure on how to
*1 drain away the water according to the Owner’s Manual.
This system is activated when engine speed exceeds maximum
recommended speed for more than 10 seconds. In addition, "Rev Limit"
―
is displayed on screen. Adopt the appropriate measure according to the
*1
Owner’s Manual.
If you continue to run, engine speed will automatically be reduced to
approximately 3000 r/min, simultaneously the buzzer sounds. Then the
―
display will be changed into "Over Revolution". Adopt the appropriate
*1
measure according to the Owner’s Manual.

This system informs the operator of the time for replacing engine oil on
―
the basis of the maintenance schedule.
*1

25
 Caution
Caution message Description
alarm icon
This system is activated when the engine oil temperature is too high
due to insufficient oil cooling or deterioration in quality of engine oil.
*1 Adopt the appropriate measure according to the Owner’s Manual.
This system is activated when the 12 volt battery voltage to the keyless
control unit drops to a point which could impair the keyless control unit
performance. Adopt the appropriate measure according to the Keyless
Start System Operation Manual.
The caution system is activated when key-fob battery voltage drops to
a point which could impair key-fob performance. Adopt the appropriate
measure according to the Keyless Start System Operation Manual.
The caution system is activated when key-fob identification error. Adopt
the appropriate measure according to the Keyless Start System
Operation Manual.
This system is activated in the event of an error of the control system of
the electronic shift. Adopt the appropriate measure according to the
*1 Owner’s Manual.
This system is activated in the event of an error of the control system of
the electronic throttle. Adopt the appropriate measure according to the
*1 Owner’s Manual.
This system is activated in the event of an error in the control system of
the electronic throttle and shift systems. Adopt the appropriate measure
*1 according to the Owner’s Manual.
This system is activated in the event of an error in the control system of
the 2nd station. Adopt the appropriate measure according to the
*1 Owner’s Manual.
This system activates when there is a communication error of the
― gauge. Adopt the appropriate measure according to the Owner’s
*1 Manual.

― This Log data is corrupt and cannot be used.

This system activates when there is a communication error of the

―
gauge. Check the connection of the wiring.
An error occurred in process of creating the QR code.
― Re-create the QR code.
Consult with your Suzuki Marine Dealer.
An error occurred in process of creating the QR code.
― Re-create the QR code.
Consult with your Suzuki Marine Dealer.

*1: This is also displayed in the gauge installed in the 2nd station.
*2: A number indicating the fault location is displayed in *_*.
(The number is displayed in the 1st station only.)

26
5. Gauge Screen List

Engine speed Speed / Fuel Fuel display All Items

Main Information
display screen display screen screen display screen
Engine speed *○ ― ― *○
Clock *1 ○ ○ ― ○
Trim position *○ ― ― *○
Shift position *○ ― ― *○
Engine position *○ ― ― *○
Ground speed *1
Speed ― ○ ― ○
Water speed *2
Total ― ○ ― ○
Remaining fuel
volume Tank 1 / Tank 2
― ― ○ ―
Tank 3 / Tank 4 *5

Engine speed Speed / Fuel Fuel display All Items

Sub Information
display screen display screen screen display screen
Total operating hours *○ *○ *○ ―
Trip time ○ ○ ○ ―
Trip distance *3 ○ ○ ○ ―
Battery voltage / Cooling water
*○ *○ *○ *△
temperature
Instantaneous fuel flow ○ ○ ○ ―
Total instantaneous
○ ○ ○ ―
fuel flow
Fuel economy
information Instantaneous fuel
○ ○ ○ ○
economy *3
Average fuel economy
○ ○ ○ ―
*3
Total fuel used ○ ○ ○ ―
Latitude / Longitude *1 ○ ○ ○ ―
Caution alarm icon / Caution message *4 *○ *○ *○ *○

*○ Displays information on the outboard motor connected.

*1: Requires input from GPS module.
*2: Requires input from water speed sensor module.
*3: Requires input from GPS module or water speed sensor module.
*4: Displays all items for the 1st station only.
*5: In case of more than dual engine application.
*△ Display cooling water temperature only.

27
6. Specifications

1 Display size 3.5 inch Color display

2 Resolution 320 x 240
3 Power voltage DC8 - 16 V
4 Display screen Horizontal
5 Dimensions without cover 105 (W) x 105 (H) x 16 (D) mm
6 Dimensions with cover 108 (W) x 110 (H) x 20 (D) mm
7 Weight 0.3 kg
8 Power consumption 2W
9 Operating temperature range -20 - 65 ℃
Built-in buzzer
10 Others Includes protective cover
NMEA 2000 output

28
・Suzuki Parameter Group Number (PGN)

Signal NMEA2000 PGN / hex Mode

RPM 127488/1F200 RX/TX

Trim Position 127488/1F200 RX/TX

Gear Position 127493/1F205 RX/TX

Water Speed 128259/1F503 RX

GPS Speed 129026/1F802 RX

Voltage 127489/1F201 RX/TX

Fuel flow 127489/1F201 RX/TX

Tank size 127505/1F211 RX/TX

Fuel level 127505/1F211 RX/TX

Engine hours 127489/1F201 RX/TX

Alarm data 127489/1F201 RX/TX

GPS Position 129029/1F805 RX

ISO Acknowledge 059392/E800 RX/TX

ISO Request 059904/EA00 RX

ISO Address claim 060928/EE00 RX/TX

Manufacturer ID 060928/EE00 RX/TX

Product info 126996/1F014 RX/TX

RX: Multi Function Gauge receives specified PGN

TX: Multi Function Gauge transmits specified PGN