Module 2

ElectroAnalytical
Techniques

Dr. Bhavna Vyas

 Reference Electrode
Definition: Reference electrode is an electrode which has stable and
reproducible electrode potential

Reference electrode:
• Reversible and obeys the Nernst equation
• Exhibits a constant potential with time
• Attains its original potential after the disturbance of small currents

Types of Reference electrode:

1) Primary Reference electrode - SHE
2) Secondary Reference electrode – Convenient to handle
Calomel electrode
Silver-Silver Chloride electrode
16-11-2024 © Bhavna M. Vyas 2
 Calomel Electrode
➢ Secondary Reference Electrode

➢ Most widely used

Construction:
Narrow Glass tube at the bottom (porous) of which liquid Hg,

above it is a paste of Hg-Hg2Cl2 and remaining portion of

glass tube is filled with 1 N/0.1 N/saturated KCl solution

A Platinum wire dipped in Hg layer for electrical contact inside glass

electrode

Side tube filled with gel act as salt bridge

16-11-2024 © Bhavna M. Vyas 3
 Calomel Electrode
Representation of Calomel Electrode: (Half Cell)
Pt Hg(l) Hg2Cl2(s) KCl(aq) (Sat.)

Reaction:
If the calomel electrode acts as cathode; (e- comes through Pt wire)
Hg2Cl2 + 2 e- ⇆ 2 Hg + 2 Cl-
And if it acts as anode (Only pure Hg loose e-), then the reaction is reverse

Potential of Calomel Electrode: Depends on Potassium Chloride conc.

The reduction potential:
Ecalomel=E0-0.0591log10[Cl-]
Std. Electrode potential of Calomel for different conc. of Cl- ions:
0.334 V for 0.1 N,
0.281V for 1 N and
0.2422 V for Saturated conc.
Demerits:
• Involves handling of Hg and Hg2Cl2
• Should
16-11-2024 not be used above 500C as Hg ©
2Cl2 gets decomposed
Bhavna M. Vyas 4
 Indicator Electrode
• Responds rapidly to the changes in the concentration of
solution under study

• Used in conjunction with the reference electrode

E.g.: Glass electrode (pH electrode), Quinhydrone electrode

16-11-2024 © Bhavna M. Vyas 5

 Ion Selective Electrode (Membrane)
• Transducer or electroanalytical sensor that converts the activity of a specific
ion dissolved in a solution into an electrical potential

• Used in conjunction with the reference electrode

• Consists of a thin membrane (selective, not specific always) which is

separated by two solutions containing same type of ions of different
concentrations and indented ion can only be transported
• Difference in concentration of ions results in Boundary
potential, from which unknown concentration can be
determined by using the known concentration of ions
in the internal solution
16-11-2024 © Bhavna M. Vyas 6
 Ion Selective Electrodes
Advantages:
➢ Portable
➢ Do not affect the test solution
➢ Short response time
➢ Wide range of concentration
➢ Unaffected by colour/turbidity
➢ Non contaminating
➢ Non-destructive

Limitations:
➢ Fouled by other solutes
➢ Interference by other ions
➢ Fragile and limited shelf life
➢ Electrodes respond to complexed ion activity
hence ligands must be absent/masked
16-11-2024 © Bhavna M. Vyas 7
 Ion Selective Electrodes
Types of Ion Selective Electrodes:
Based on membranes used Ion Selective Electrodes (ISE) can be
classified as:

➢ Glass Electrode ( glass membrane specifically for H+ Ions)

➢ Solid State Electrode (crystalline membrane for F- or C- ions)

➢ Enzyme Electrode (urease on polyacrylamide gel for 𝑁𝐻4+ ions )

➢ Gas Sensing Electrode

16-11-2024 © Bhavna M. Vyas 8

 Glass Electrode
➢ Indicator Electrode & a type of ISE
➢ Used for pH determination

Construction:

Long glass tube with thin walled pH

sensitive glass membrane at the
bottom filled with 0.1 M HCl solution

A Platinum wire or AgCl coated Ag wire

dipped in HCl solution for electrical
contact
16-11-2024 inside glass electrode © Bhavna M. Vyas 9
 Glass Electrode
Construction:

Glass used in glass membrane is porous in structure and may be

of silicate type or calcinogenide glass. Silicate glass is generally used for

monovalent cations while calcinogenide for divalent cations detection

Silicate or Special glass composition: 72% SiO2, 22% Na2O, 6%CaO

Representation of Glass Electrode: (Half Cell)

Ag, AgCl HCl (0.1 M) Glass membrane H+ (Test)

16-11-2024 © Bhavna M. Vyas 10
 Glass Electrode
Working of Glass Electrode:
➢ Glass bulb acts as a semipermeable for H + ions

➢ On immersing glass electrode in a solution, glass membrane gets hydrated

➢ Exchange of H+ ions with Na+ ions takes place on both sides of hydrated
glass membrane

➢ Results into Boundary Potential

➢ An equilibrium gets established on both sides:

𝐻 + + 𝑁𝑎+ 𝐺𝑙𝑎𝑠𝑠 − ⇌ 𝑁𝑎+ + 𝐻+ 𝐺𝑙𝑎𝑠𝑠 −

16-11-2024 © Bhavna M. Vyas 11

 Glass Electrode
Working of Glass Electrode:
➢ Boundary Potential develops across the glass membrane as a result of a
concentration difference of H+ ions on two sides of the membrane (H+ ions
can pass through the membrane being small in size while Cl - cannot being
bigger, thus only H+ ions concentration is measured)
pH of Solution:
➢ Glass electrode coupled with calomel electrode can be used to determine
pH of a solution.
➢ Electrodes are dipped into the solution of unknown pH
Representation of cell:
Pt. Hg, Hg2Cl2 Cl- aq. Test Solution Glass electrode
16-11-2024 © Bhavna M. Vyas 12
 Glass Electrode
Advantages of Glass Electrode:

➢ Portable and compact

➢ Attains equilibrium easily
➢ Stable electrode, used in strong oxidizing and reducing agents
➢ Accurate and quick results
➢ Detect H+ ions in the presence of other type of ions as well

Uses:
• Pure research,
• Control of industrial processes
• Analysis of foods and cosmetics
• Measurement of environmental indicators
• Microelectrode measurements such as cell membrane electrical potential
• Soil acidity.
16-11-2024 © Bhavna M. Vyas 13
 Glass Electrode
pH of Solution:
Pt. Hg, Hg2Cl2 Cl- aq. Test Solution (Unknown H+) Glass electrode

EMF of cell (ECell):

ECell = ECalomel – EGlass

= 0.2422 – (𝐸𝐺0 + 0.0591pH)

0
𝐸𝐶𝑒𝑙𝑙 +𝐸𝐺 −0.2422
pH=
0.0591

where, 𝐸𝐺0 - potential of glass electrode when electrode

is in contact with known pH
16-11-2024 © Bhavna M. Vyas 14
pH-Metry
Objective:

Electro-analytical technique: pH-metry

Learning Outcomes:

• Method of material analysis

• Selection appropriate electro-
analytical technique
16-11-2024 © Bhavna M. Vyas 16
 Introduction
pH: Represent Hydrogen Ion Concentration

Definition ??

Defined as the negative logarithm of hydrogen ion concentration

pH = -log [H+]

where [H+] is the concentration of hydrogen ion in moles/litre

Applications of pH measurements:

Water treatment, Food Industry, Agriculture etc.

Laboratory/Industries – Required to Maintain pH of solution

16-11-2024 © Bhavna M. Vyas 17

 pH of some real samples

16-11-2024 © Bhavna M. Vyas 18

Buffer Solution: Resists the pH change in solution
Acidic buffer
A solution that contains a weak acid and its salt
with a strong base.
For example, a mixture of acetic acid (CH3COOH) and
sodium acetate (CH3COONa)
Basic buffer
A solution that contains a weak base and its salt
with a strong acid.
For example, a mixture of ammonium hydroxide
(NH4OH) and ammonium chloride (NH4Cl)
16-11-2024 © Bhavna M. Vyas 19
 pH Metry
What is pH Metry ????

Its an electro-analytical technique in which pH of a solution is

measured using pH meter

Where it is used ??

It is an important application of potentiometry

for the determination of pH

To determine
16-11-2024
equivalence point of© Bhavna
titration
M. Vyas 20
 pH-metric Titration of SASB
Objective: To determine the unknown concentration of strong acid

using pH-metry.

Consider a SASB titration in which both, the acid (HCl) and base

(NaOH) dissociate completely.

Reaction:
H + +Cl - + Na+ +OH - ® Na+ +Cl - + H 2O

16-11-2024 © Bhavna M. Vyas 21

 pH-metric Titration of SASB
Glass Electrode

Procedure:
➢ First calibrate the pH meter
using buffer solutions of
pH meter
known pH 4, 7 and 9

16-11-2024 © Bhavna M. Vyas 22

 pH-metric Titration of SASB
Procedure:

➢ Take known quantity of HCl in a beaker (V1) with magnetic needle in it and
then keep it on the magnetic stirrer.
A picture containing indoor, table, sitting,
glass

➢ Immerse the indicator electrode (glass) and reference Description automatically generated

electrode in beaker, start the magnetic stirrer

➢ Note down the pH of the pure acid solution

➢ Fill the burette with 0.1 N NaOH

➢ Add 0.5 ml of N/10 NaOH to the acid in the

beaker
16-11-2024 © Bhavna M. Vyas 23
 pH-metric Titration of SASB
Procedure:
➢ Continue addition of NaOH from the burette and note down the
corresponding pH after each addition. Near the equivalence point the
change in pH is much more rapid than in any other region.

➢ Stop the addition when pH value remains

nearly constant.

➢ Note down all corresponding pH for

different Volumes of Base added

16-11-2024 © Bhavna M. Vyas 24

 pH-metric Titration of SASB

Observations:

➢ Initial Volume of acid taken = V1 ml pH

➢ Volume of strong base added

➢ pH of the solution of reaction mixture

Volume of Strong Base added
(ml)

Calculations: Plot a pH metric Titration curve

Plot of pH verses Volume of Strong Base added

16-11-2024 © Bhavna M. Vyas 25

pH metric Titration Curve for SASB

pH

Volume of Strong Base added (ml)

16-11-2024 © Bhavna M. Vyas 26
pH metric Titration Curve for SASB

pH

Volume of Strong Base added (ml)

16-11-2024 © Bhavna M. Vyas 27
pH metric Titration Curve for SASB

pH

Volume of Strong Base added (ml)

16-11-2024 © Bhavna M. Vyas 28
pH metric Titration Curve for SASB

pH

Volume of Strong Base added (ml)

16-11-2024 © Bhavna M. Vyas 29
pH metric Titration Curve for SASB

At equivalence point, equal amounts of H+ and OH-

pH=7 combine to form water at pH=7

pH
Vb at Equivalence point

Vb
Volume of Strong Base added (ml)
16-11-2024 © Bhavna M. Vyas 30
 pH-metric Titration of SASB
Calculations: Using the following equivalence equation:

Strong Acid vs Strong Base

N1V1= N2V2

Normality of HCL is obtained and from that Strength of acid using

following:

𝟑𝟔. 𝟓 ∗ 𝑵𝒐𝒓𝒎𝒂𝒍𝒊𝒕𝒚 𝒐𝒇 𝑨𝒄𝒊𝒅 ∗ 𝑽𝒐𝒍𝒖𝒎𝒆 𝒐𝒇 𝒃𝒂𝒔𝒆 𝒂𝒕 𝑬𝒒. 𝒑𝒐𝒊𝒏𝒕

𝑺𝒕𝒓𝒆𝒏𝒈𝒕𝒉 𝒐𝒇 𝑨𝒄𝒊𝒅 𝒈Τ𝒍 =
𝑽𝒐𝒍𝒖𝒎𝒆 𝒐𝒇 𝑨𝒄𝒊𝒅 𝒕𝒂𝒌𝒆𝒏

16-11-2024 © Bhavna M. Vyas 31

Test yourself…. Tick mark the right answer:
1. pH is defined as:

a) Positive logarithm of Hydrogen ions

b) Negative logarithm of Hydrogen ions

c) Positive logarithm of Hydroxide ions

d) Negative logarithm of Hydroxide ions

2. In SASB pH-metric titration curve, value of pH shows inflection at

a) near equivalence point

a) at equivalence point

a) after equivalence point

a) at all points
16-11-2024 © Bhavna M. Vyas 32
Test yourself…. Tick mark the right answer:
1. pH-metry is:

a) an electroanalytical technique

b) instrumental method of analysis

c) gravimetric technique

d) volumetric analysis using indicators

2. Indicator electrode used in pH meter for the determination of Hydrogen ions

a) Calomel electrode

b) Fluoride electrode

c) Glass electrode

d) Conductivity cell
16-11-2024 © Bhavna M. Vyas 33
 Few subjective questions

1. Define pH. What do you mean be pH scale?

2. What is pH-metry?

3. Draw the titration curve for pH-metric titration of HCL and NaOH.

4. Explain pH-metric titration curve of Strong Acid (HCL) and Strong Base (NaOH).

5. Why pH of the solution is 7.0 at equivalence point of strong acid-strong base

titration?

16-11-2024 © Bhavna M. Vyas 34

 Conductometry
Conductometry is an electroanalytical technique which deals with the
measurement of electrical conductance of solutions containing
electrolytes (acids, bases and salts in water). These solutions conduct
electric current due to the movement of ions towards oppositely charged
electrodes. Solutions of electrolytes also obey Ohm’s Law like metallic
conductors (R=E/I).
Conductance: It is the reciprocal of resistance. It is the ease of the flow of
current through a solution of electrolyte
Unit: Ohm-1 or Mho or Seimen

16-11-2024 © Bhavna M. Vyas 35

 Conductometry
Conductivity is a parameter used to measure the ionic concentration and
activity of a solution.
The more salt, acid or alkali in a solution, the greater its conductivity
The unit of conductivity is S/m or S/cm.
The scale for aqueous solutions begins with pure water at a conductivity of
0.05 µS/cm (25 °C) and naturally occurring waters such as drinking water or
surface water have a conductivity in the range 100 - 1000 µS/cm.
Conductivity cells are specially used for
the measurements of the conductance

16-11-2024 © Bhavna M. Vyas 36

 Basic Definitions of Conductometry
Conductance: It is the reciprocal of resistance. Unit: Ohm-1 or Mho or Siemen

Specific Conductance: Specific conductance of a solution can be defined as the

conductance of solution between two parallel electrodes which have cross sectional area 1
cm2 and which are kept 1 cm apart. Unit: Mho-cm-1

Equivalent Conductance: It is defined as the conductance of a solution containing one gram

equivalent of an electrolyte at any particular concentration, when placed between two
electrodes 1 cm apart. Unit: Mho-cm2-gm-equiv.-1

Molar Conductance: It is defined as the conductance of a solution containing one mole of an

electrolyte at any particular concentration, when placed between two electrodes 1 cm apart.

Unit: Mho-cm2 -gmole-1

𝑺𝒑𝒆𝒄𝒊𝒇𝒊𝒄 𝑪𝒐𝒏𝒅𝒖𝒄𝒕𝒂𝒏𝒄𝒆
Cell Constant= 𝑶𝒃𝒔𝒆𝒓𝒗𝒆𝒅 𝑪𝒐𝒏𝒅𝒖𝒄𝒕𝒂𝒏𝒄𝒆 or ratio of distance between the two electrodes to the area
16-11-2024 © Bhavna M. Vyas 37
of electrodes (l/a) Unit: cm-1 or m-1
 Basic Definitions of Conductometry
Factors influencing Conductance:

➢ Number of free ions: More the no of free ions, greater is the conductance

➢ Charge on the free ions: Greater the charge, greater is the conductance

➢ Mobility of ions: Greater the mobility, greater is the conductance

Effect of Temperature:

➢ Conductance increases with increase in temperature due to increase in

velocity of ions, decrease in viscosity of the medium and decrease in the

interaction between the ions

16-11-2024 © Bhavna M. Vyas 38
 Basic Definitions of Conductometry
Effect of dilution on Conductivity:

➢ Equivalent or Molar Conductance increases

with increase in dilution.

Equivalent Conductance

Strong Electrolyte ➢ Increased Dissociation of the electrolyte on

dilution while for strong electrolyte increase

Weak Electrolytes is due to the increased mobility of ions.

➢ Specific conductance of the solution

Root of Concentration C
Dilution decreases on dilution (due to decrease in

the concentration of ions per unit volume)

16-11-2024 © Bhavna M. Vyas 39
 Conductivity Cell
➢ Conductivity Cells are of various shapes and sizes
➢ The simplest kind of measuring cell used consists of two similar electrodes.
➢ They are made up of pyrex glass (or some other resistant glass) which is fitted
with a pair of Platinum electrodes. These electrodes are platinum plates fused
into the glass tubes. The tubes are firmly supported by an ebonite cover.

Copper Wire
Ebonite Cover (Epoxy Resin)
Glass Cell

Mercury Contact

Platinum Electrodes

Electrolytic Solution
16-11-2024 © Bhavna M. Vyas 40
 Conductivity Cell
➢ The cover along with the platinum electrodes is fitted into the pyrex glass vessel so

that the distance between the electrodes may not change.

➢ An alternating voltage applied to one of the conductivity electrodes causes the ions

in the solution to migrate towards the electrodes.

➢ The more ions in the solution, the greater the current which flows between the

conductivity electrodes.

16-11-2024 © Bhavna M. Vyas 41

 Conductivity Cell
Conductivity cell measurements: Conductivity is measured by using a

conductivity cell to make a measurement of the electrical resistance.

➢ The conductivity meter measures the current produced by the conductivity

cell and uses Ohm's law to calculate first the conductance of the solution

and then - by taking the cell data into account - the conductivity.

16-11-2024 © Bhavna M. Vyas 42

 Conductometric Titrations
➢ It is a standard technique used in conductometry which has notable
application in analytical chemistry.

➢ In this method we determine the point where reaction is completed

(equivalence point) with the help of a conductometer that measures the
changes in conductance of solution produced by the ions in the
solution.

➢ At equivalence point we measure the volume of base used to neutralize

the acid ions completely in the solution. Putting these values in formula
we can get the strength of acid
16-11-2024 © Bhavna M. Vyas 43
 Conductometric Titrations
➢The principle of conductometric titration is based on the fact that

during the titration, one of the ions is replaced by the other and

invariably these two ions differ in the ionic conductivity with the result

that conductivity of the solution varies during the course of titration.

➢ The equivalence point may be located graphically by plotting the

change in conductance as a function of the volume of titrant added.

16-11-2024 © Bhavna M. Vyas 44

 Strong Acid with a Strong Base Conductometric Titration

Consider titration of HCl against NaOH wherein Strong base is filled in burette

and acid is taken in a beaker

Chemical reaction: HCl + NaOH → NaCl + H2O

H+ + Cl- + Na+ + OH- → Na+ +Cl- + H2O

1. Initially, before titration the conductance is high which is due to

HCl → H+ + Cl- and

mobility of H+ is 350 and that of Cl-©ion

16-11-2024 isVyas73.
Bhavna M. 45
Strong Acid with a Strong Base Conductometric Titration Curve

Conductometric
Conductance

Titration of Strong
Acid vs. a Strong
Base End point

Volume of Titrant (ml)

16-11-2024 © Bhavna M. Vyas 46

 Strong Acid with a Strong Base Conductometric Titration

2. Before Equivalence Point: Upon addition of NaOH, the H ion reacts with
OH ion to form the very weakly ionized water molecule. This means that the H+
ion is removed from the medium and replaced by Na+ ion which has a mobility
of 43; thus, a continuous abrupt decrease in conductance occurs during the
titration till the end point.

3. After Equivalence Point: Beyond the end point there is excess Na+ and OH-
ions with 43 and 198 mobility due to continuous addition of NaOH So there is
continuous increase in conductance and the curve will have a V shape.

4. The equivalence point (end point) is the intersection of this two lines which is
a minimum
16-11-2024 of the curve. © Bhavna M. Vyas 47
Strong Acid with a Strong Base Conductometric Titration

Calculations: Using the following equivalence equation:

Strong Acid vs Strong Base

N1V1= N2V2

Normality of HCL is obtained and from that Strength of acid using

following:
𝑺𝒕𝒓𝒆𝒏𝒈𝒕𝒉 𝒐𝒇 𝑨𝒄𝒊𝒅 𝒈Τ𝒍

𝟑𝟔. 𝟓 ∗ 𝑵𝒐𝒓𝒎𝒂𝒍𝒊𝒕𝒚 𝒐𝒇 𝑨𝒄𝒊𝒅 ∗ 𝑽𝒐𝒍𝒖𝒎𝒆 𝒐𝒇 𝒃𝒂𝒔𝒆 𝒂𝒕 𝑬𝒒. 𝒑𝒐𝒊𝒏𝒕

=
𝑽𝒐𝒍𝒖𝒎𝒆 𝒐𝒇 𝑨𝒄𝒊𝒅 𝒕𝒂𝒌𝒆𝒏

16-11-2024 © Bhavna M. Vyas 48

 Weak Acid with a Strong Base Conductometric Titration

Consider titration of CH3COOH against NaOH wherein Strong base is filled in

burette and weak acid is taken in a beaker

Chemical reaction: CH3COOH + NaOH → CH3COONa + H2O

H+ + CH3COO- + Na+ + OH- → CH3COO- + Na+ + H2O

1. Initially, before titration the conductance is low which is due to weak acid.

16-11-2024 © Bhavna M. Vyas 49

 Weak Acid with a Strong Base Conductometric Titration Curve

Conductometric
Titration of Weak
Conductance

Acid vs. a Strong

Base
End point

Volume of Titrant (ml)

16-11-2024 © Bhavna M. Vyas 50

 Weak Acid with a Strong Base Conductometric Titration

2. Before Equivalence Point: First conductance decreases on addition of strong base

owing to the formation of the salt which suppresses the ionization of weak acid. Mostly
this decrease is not observed unless one adds very small volumes of NaOH. As more of
NaOH is added, highly ionized salt, sodium acetate is formed thereby increasing the
conductance. Conductance increase occurs during the titration till the end point.

3. After Equivalence Point: Beyond the end point there is excess Na+ and OH- ions
with 43 and 198 mobility due to continuous addition of NaOH, So there is continuous
increase in conductance.

4. Equivalence point (end point) is the intersection of this two lines.

16-11-2024 © Bhavna M. Vyas 51

 Strong Acid with a Weak Base Conductometric Titration

Consider titration of HCl against NH4OH wherein weak base is filled in burette

and acid is taken in a beaker

Chemical reaction: HCl + NH4OH → NH4Cl + H2O

H+ + Cl- + NH4+ + OH- → NH4+ +Cl- + H2O

1. Initially, before titration the conductance is high which is due to HCl → H+ + Cl-

and high mobility of H+.

16-11-2024 © Bhavna M. Vyas 52

 Strong Acid with a Weak Base Conductometric Titration Curve

Conductometric
Conductance

Titration of Strong
Acid vs. a Weak
Base
End point

Volume of Titrant (ml)

16-11-2024 © Bhavna M. Vyas 53

 Strong Acid with a Weak Base Conductometric Titration

2. Before Equivalence Point: Upon addition of NH4OH, the conductance first

decreases due to the replacement of H+ ions. It keeps on decreasing upto the
equivalence point.

3. After Equivalence Point: Beyond the end point i.e. after the whole of acid is
neutralised, the conductance remains almost constant because the weakly ionised
excess base do not produce appreciable change in conductance.

4. The equivalence point (end point) is the intersection of this two lines.

16-11-2024 © Bhavna M. Vyas 54

 Weak Acid with a Weak Base Conductometric Titration

Consider titration of CH 3COOH and NH4OH, wherein weak base is filled in burette

and weak acid is taken in a beaker

Chemical reaction: CH3COOH + NH4OH → CH3COONH4 + H2O

H+ + CH3COO- + NH4+ + OH- → CH3COO- + NH4+ + H2O

1. Initially, before titration the conductance is low which is due to weak acid.

16-11-2024 © Bhavna M. Vyas 55

 Weak Acid with a Weak Base Conductometric Titration Curve

Conductometric
Titration of
Weak
End point Acid vs.
Conductance

a Weak Base

Volume of Titrant (ml)

16-11-2024 © Bhavna M. Vyas 56

 Weak Acid with a Weak Base Conductometric Titration

2. Before Equivalence Point: First conductance decreases on addition of weak base

due to the replacement of H+ ions. But it soon begins to increase due to the salt
formation. Conductance increase occurs during the titration till the end point.

3. After Equivalence Point: After the whole of acid is neutralised, the conductance
remains almost constant because the weakly ionised excess base do not produce
appreciable change in conductance.

4. The equivalence point (end point) is the intersection of this two lines

16-11-2024 © Bhavna M. Vyas 57

 Advantages of Conductometric Titrations
➢ Employed to very dilute solutions (upto the order of 10-4 M solutions).

➢ Very accurate end points (with an error of ±0.5%).

➢ Very useful for coloured solutions (colour change of indicator is not clear)

➢ Useful for WAWB titration, which otherwise do not give sharp end point

➢ Keen observation is not necessary near the end point as it is obtained graphically

16-11-2024 © Bhavna M. Vyas 58

Spectroscopic Techniques
UV-Visible Spectroscopy
 Spectroscopy
• Spectroscopy is branch of science deals with the study of interaction of
electromagnetic radiation with matter

• Spectroscopic methods of analysis are based on the measurement of

electromagnetic radiation absorbed or emitted by the sample

• Physical and chemical properties of the sample substance are directly

related to the structure of the sample and sample substance absorb
radiations based on its bonding and structure

• Structure elucidation can be done based on wavelength absorbed by

sample substance
16-11-2024 © Bhavna M. Vyas 60
 Spectroscopy
Electromagnetic Radiations:

• Consists of discrete packets of energy which are called photons of light.

• Energy of photon of EMR is given by: E = hc/ λ

• EMR travels at 3 x 108 m/sec. The speed of the wave is given by:

Velocity = Wavelength x Frequency

• These waves made of two components electrical and magnetic. They

oscillates in space perpendicular to each other and perpendicular to the
direction of propagation.

• Wavelength of radiation is inversely proportional to its energy.

16-11-2024 © Bhavna M. Vyas 61
 Spectroscopy

16-11-2024 © Bhavna M. Vyas 62

 Fundamental Laws of Spectroscopy

Lambert’s law : When a beam of light is allowed to pass through a

transparent solution, the rate of decrease in intensity of light is directly
proportional to thickness of solution.
Beer’s law: When a beam of light is allowed to pass through a transparent
solution, the rate of decrease in intensity of light is directly proportional to
concentration of solution when thickness of solution is kept constant.
16-11-2024 © Bhavna M. Vyas 63
 Fundamental Laws of Spectroscopy

16-11-2024 © Bhavna M. Vyas 64

 Spectroscopy
Spectroscopic methods of analysis are based on the measurement of
electromagnetic radiations absorbed or emitted by the sample solution.

Most common photometric methods are:

1. Colorimetric: (400 to 800 nm)

2. UV spectroscopy (180 to 400 nm)

3. Visible spectroscopy (400 to 800 nm)

4. UV visible spectroscopy (180 to 800nm)

5. IR (0.76 to 15 micrometer)
16-11-2024 © Bhavna M. Vyas 65
 Range of UV-Visible Spectroscopy
▪ Range of wavelengths belong to UV and Visible region.

UV region: 10nm to 400nm

Visible region: 400nm to 800nm

▪ Subdivision of Ultraviolet region based on wavelengths:

Far UV (below 200nm) & Near UV(from 200 – 400nm)

▪ UV-Visible wavelengths are used in Quantitative as well as Qualitative analysis

in which absorption laws are used.

▪ In Quantitative analysis graph of absorbance against concentrations is usually

plotted.

16-11-2024 © Bhavna M. Vyas 66

 Spectroscopy

Interaction of electromagnetic radiation with matter

UV visible Radiation: bring excitation of electrons in the bond to

higher energy anti bonding level

Absorption of IR: Cause vibration in certain covalent bonds

∆ E rotational < ∆ E vibrational < ∆ E electronic

16-11-2024 © Bhavna M. Vyas 67

 Absorption of UV radiation leading to
Electronic transitions in organic molecules

• Absorption of UV-visible radiation by a molecule brings changes in the electronic

energy of molecule because of transition of valence electrons from lower energy
to higher energy. Types of electrons present in organic molecule:

1. Sigma (σ) electrons: Electrons forming single bonds like C-H bond present in
saturated hydrocarbon

2. pi (π) electrons: Electrons forming double bonds like C=C bond present in
unsaturated hydrocarbon

3. Non bonded (ɳ) electrons: Non-bonded or lone pair of electrons and not
involved in bonding between atoms in molecules. Lone pair of electrons
present on Oxygen, Nitrogen etc.
16-11-2024 © Bhavna M. Vyas 68
 Absorption of UV radiation leading to
Electronic transitions in organic molecules

When energy is absorbed in UV Visible region, electronic transitions occur:

➢ Possible Electronic Transitions:

1) σ→ σ* transition

2) π→ π* transition

3) ɳ→ σ*transition

4) ɳ→π*transition

➢ Forbidden Transitions:

1) σ→π*transition

2) 2) π →σ* transition
16-11-2024 © Bhavna M. Vyas 69
 Electronic Energy Levels and Transitions

16-11-2024 © Bhavna M. Vyas 70

 Electronic transitions in organic molecules
➢ Possible Electronic Transitions:

1. σ→ σ* transition: (Less than 150 nm)

Such transitions occur only in the compounds containing sigma electrons
which are involved in single bonds and no lone pair of electrons on any atom in the
molecule from sigma bonding orbital to the corresponding antibonding orbital σ* .
Such transitions requires very large amount of energy, the absorption band occurs
in the far ultraviolet region.
e.g. Saturated Hydrocarbons like Methane, Ethane etc.
Methane (CH4) containing C-H bonds undergo this transition, shows absorbance
maxima at 125 nm
16-11-2024 © Bhavna M. Vyas 71
 Electronic transitions in organic molecules

➢ Possible Electronic Transitions:

2. π→ π* transition: (200 nm-700 nm)

Such transitions occur only in the compounds containing pi electrons which are
involved in multiple bonds in the molecule. These electrons get excited from pi
bonding orbital to the corresponding antibonding orbital π* .
e.g. Unsaturated Hydrocarbons like alkenes, alkynes, nitriles, aromatic compounds
etc. show these transitions.
Generally alkenes absorb in the region of 180-200 nm while compounds containing
2 or more conjugated bonds shows absorbance maxima above 200 nm

16-11-2024 © Bhavna M. Vyas 72

 Electronic transitions in organic molecules

➢ Possible Electronic Transitions:

3. ɳ→ σ* transition: (150 - 250 nm)

Such transitions occur in the saturated compounds containing atoms with

lone pair of electrons (non-bonding electrons) like O, N, S and halogens. These
electrons get excited from non-bonding orbital to the antibonding orbital σ*.

e.g. Various functional groups show absorbance maxima at shorter wavelength

in the range of 150 - 250 nm

16-11-2024 © Bhavna M. Vyas 73

 Electronic transitions in organic molecules

➢ Possible Electronic Transitions:

4. ɳ→π* transition: (200 nm-700 nm)

Such transitions occur in the compounds containing double bonds involving
hetero atoms with lone pair of electrons (non-bonding electrons) like O, N, S and
halogens. These electrons get excited from non-bonding orbital to the antibonding
orbital π*.
These transition requires minimum energy and show absorption at longer
wavelength between 200 to 700 nm

16-11-2024 © Bhavna M. Vyas 74

 Electronic Transitions in Organic Molecules

16-11-2024 © Bhavna M. Vyas 75

 UV-Visible Spectra
➢ UV-Visible spectrophotometer on analysis of an analyte solution gives

data in the form of UV-Visible Spectra

➢ The UV-Vis spectra is a graph:

Absorbance verses wavelength () or

% Transmittance verses Wavelength ()

➢ It gives information about max

16-11-2024 © Bhavna M. Vyas 76

 UV-Visible Spectroscopy
max : It is defined as a particular wavelength at which maximum

absorbance is observed. It is a charactristic property of an analyte and

depends on strucutre of that analyte

 : It is called as molar extinction coefficient or molar absorptivity

It is the extent of absorption for a solution specific concentration

16-11-2024 © Bhavna M. Vyas 77

 UV-Visible Spectroscopy
The UV-Vis spectra for isoprene is as follows:

Source: https://www.chemistry.msu.edu
16-11-2024 © Bhavna M. Vyas 78
 Content: UV-visible spectroscopy

Terms Involved in UV Visible Spectroscopy:

Definition and suitable examples to illustrate the following terms:
➢ Chromophore:
➢ Auxochrome:
➢ Bathochromic shift:
➢ Hypsochromic shift:
➢ Hyperchromic shift:
➢ Hypochromic shift:

16-11-2024 © Bhavna M. Vyas 79

 Terms involved in UV-visible spectroscopy
CHOMOPHORE: Any isolated covalently bonded unsaturated group responsible for
electronic absorption or shows characteristic absorption in the UV Visible region.
E.g.: -C=C-, -C=O, NO2
Consequently, chromophore is any substance (groups) which absorbs radiation at
particular wave length which may or may not impart colour to the compound.

AUXOCHROME: Any saturated group with non bonded electrons, which does not
itself act as a chromophore but whose presence brings about a shift of the
absorption band towards the red end of the spectrum (longer wavelength)
Auxochrome is a colour enhancing group. Auxochrome when attached to a
chromophore, alters both the wavelength and the intensity of the absorption
E.g. –NH2, -OH, -OR, -NHR, -SH etc.
16-11-2024 © Bhavna M. Vyas 80
Chromophore + Auxochrome = Newer Chromophore
 Terms involved in UV-visible spectroscopy
BATHOCHROMIC SHIFT or RED SHIFT:

The shift of maximum absorption to a longer wavelength due to

substitution or solvent effect.

Causes:

1. An auxochrome

2. Change of solvent

E.g.: Absorption Maximum of Benzene λmax= 255 nm (εmax= 203)

While for Pheonl λmax= 270 nm and Aniline λmax= 280 nm (εmax= 1430)

In alkaline medium, p-nitrophenol shows red shift with λmax=265 nm from

λmax=255 nm. Because negatively charged Oxygen delocalizes electron more
effectively than the unshared n electron pair present on –OH groups.
16-11-2024 © Bhavna M. Vyas 81
 Terms involved in UV-visible spectroscopy

HYPSOCHROMIC SHIFT or BLUE SHIFT: The shift of maximum absorption to

a shorter wavelength.

Causes:

1) Change of solvent towards higher polarity or

2) Removal of conjugation

E.g.: Absorption Maximum of Aniline (conjugation of pair electrons of nitrogen

with benzene ring) λmax= 280 nm while Aniline shows λmax= 203 nm as in acidic
medium as it will form –NH+3, due to removal of lone pair of electrons or due to
removal of –conjugation.

16-11-2024 © Bhavna M. Vyas 82

 Terms involved in UV-visible spectroscopy

HYPERCHROMIC EFFECT:

An increase in maximum absorption intensity

Cause: Introduction of auxochrome usually increases the intensity of

absorption

E.g. : Pyridine λmax= 257 nm and εmax= 2750 while pyridine with –CH3 group
shows increase in intensity of absorption that is 2-methyl pyridine λmax= 262
nm and εmax= 3560

16-11-2024 © Bhavna M. Vyas 83

 Terms involved in UV-visible spectroscopy

HYPOCHROMIC EFFECT:

A decrease in maximum absorption intensity.

Cause: Due to introduction of any group to the compounds which is going to alter
the molecular pattern of the compound or distort the original geometry results in a
hypochromic shifts

E.g.: Biphenyl (or naphthalene) has an absorption λmax= 250 nm and εmax= 19000
whereas 2-methyl biphenyl has an absorption of λmax= 237 nm and εmax= 10250

16-11-2024 © Bhavna M. Vyas 84

 Effect of substituents on the position and
intensity of an absorption band

16-11-2024 © Bhavna M. Vyas 85

Source of Image: epgp.inflibnet.ac.in
Instrumentation: Single Beam UV Visible Spectrophotometer

Block Diagram of Single Beam UV Visible Spectrophotometer:

Amplifier/
Monochromator Sample Recorder
Source Detector
Cell

Components of Single Beam UV Visible Spectrophotometer:

1) Light Source: Provides wide range of UV Visible radiation

and sufficient intensity over required wavelength.
Eg: Deuterium/Hydrogen Discharge Lamp (190-290 nm);
16-11-2024 Tungsten filament (370-780
© Bhavna M. Vyas nm) 86
Instrumentation: Single Beam UV Visible Spectrophotometer

Source of radiation Sample holder (Cuvette)

16-11-2024 © Bhavna M. Vyas 87

Instrumentation: Single Beam UV Visible Spectrophotometer

Amplifier
Monochromator Sample /Recorde
Source Detector r
Cell

2) Sample Holder: All UV Visible spectra are recorded for the

solution phase. Hence, Cells/Cuvettes made up of Glass or
Quartz are used. But Quartz Cells only are transparent in full
range of 200-780 nm.

3) Monochromator: Converts polychromatic radiation into

monochromatic radiation using Prism/Filters/Gratings. Quartz
prism is used for UV region

4) Detector: Transducer which converts transmitted radiation

into electric signal/current. Commonly used are
16-11-2024 Photomultiplier tube(PMT), Phototube
© Bhavna M. Vyas etc. 88
Instrumentation: Single Beam UV Visible Spectrophotometer
Amplifier
Monochromator Sample /Recorde
Source Detector r
Cell

5) Amplifier: Amplify the signal received from detector

6) Recorder: Record output of the UV Visible spectrum data

and Display it either in the graphical manner as absorption
spectra or in the form of digital values of the Absorbance or
transmittance verses wavelength

16-11-2024 © Bhavna M. Vyas 89

 Applications of UV-Visible Spectroscopy

➢Structural Information: max is the characteristic property of a

molecule due to presence of chromophore along with auxochrome. By

knowing this value structural information can be extracted.

➢Qualitative analysis: UV-Visible spectra of an unknown sample can

be matched with spectra of known compound to analyse sample

qualitatively.

16-11-2024 © Bhavna M. Vyas 90

 Applications of UV-Visible Spectroscopy

• Quantitative analysis: By use of UV-Visible Spectroscopy, unknown

concentration of analyte can be evaluated. Here same analyte solution
is prepared with different concentration and its absorption is
determined. A graph is plotted with absorption verses concentration,
which gives a straight line.

• Now absorption of solution containing unknown concentration is

evaluated and by use of graph its corresponding concentration can be
determined.

16-11-2024 © Bhavna M. Vyas 91

 Applications of UV-Visible Spectroscopy

➢Chemical Kinetics: According to Beer’s Law absorbance is proportional

to concentration. Hence during the chemical reaction absorption

intensity of reactant decreases, while that of Product increases which will

help to study chemical kinetics.

➢Detection of Impurity: Any change in the spectra of a specific

compound will indicate the presence of impurity

16-11-2024 © Bhavna M. Vyas 92

THANK YOU