Scribd
Upload
2K views

Port Timing Diagram of Two Stroke Cycle Pertrol Engine

In a two-stroke engine, ports instead of valves allow air and fuel in and exhaust out. There are three ports: the inlet port opens from BDC to TDC for air intake, the transfer port opens from TDC to BDC to transfer fuel from the crankcase, and the exhaust port opens from TDC to BDC for exhaust. To draw the port timing diagram, the engine is rotated and marks are made when the piston exposes or covers the ports, measuring the distances from TDC or BDC. The inlet, exhaust, and transfer port opening and closing distances are equal.

Uploaded by

mechanical-engg
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
2K views

Port Timing Diagram of Two Stroke Cycle Pertrol Engine

In a two-stroke engine, ports instead of valves allow air and fuel in and exhaust out. There are three ports: the inlet port opens from BDC to TDC for air intake, the transfer port opens from TDC to BDC to transfer fuel from the crankcase, and the exhaust port opens from TDC to BDC for exhaust. To draw the port timing diagram, the engine is rotated and marks are made when the piston exposes or covers the ports, measuring the distances from TDC or BDC. The inlet, exhaust, and transfer port opening and closing distances are equal.

Uploaded by

mechanical-engg
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

PORT TIMING DIAGRAM OF TWO STROKE CYCLE PERTROL ENGINE

Ex.No. : Date:

Aim :
To draw the port timing diagram of given two stroke cycle petrol engine .

Apparatus Required :
1. Two stroke petrol engine 2. Measuring tape 3. Chalk

Theory and Description :


In the case of two stroke cycle engines the inlet and exhaust valves are not present . Instead , the slots are cut on the cylinder itself at different elevation and they are called ports. There are three ports are present in the two stroke cycle engine . 1. Inlet port 2. Transfer port 3. Exhaust port The diagram which shows the position of crank at which the above ports are open and close are called as port timing diagram. The extreme position of the piston at the bottom of the cylinder is called Bottom Dead centre [BDC] . The extreme position of the piston at the top of the cylinder is called TOP dead centre [TDC ] In two stroke petrol engine the inlet port open when the piston moves from BDC to TDC and is closed when the piston moves from TDC to BDC . The transfer port is opened when the piston is moved from TDC to BDC and the fuel enters into the cylinder through this transport from the crank case of the engine . The transfer port is closed when piston moves from BDC to TDC . The transfer port opening and closing are measured with respect to the BDC . The exhaust port is opened , when the piston moves from TDC to BDC and is closed when piston moves from BDC to TDC . The exhaust port opening and closing are measured with respect to the BDC.

Procedure :
1. Remove the ports cover and identify the three ports . 2. Mark the TDC and BDC position of the fly wheel . To mark this position follow the same procedure as followed in valve timing diagram . 3. Rotate the flywheel slowly in usual direction (usually clockwise ) and observe the movement of the piston 4. When the piston moves from BDC to TDC observe when the bottom edge of the piston . Just uncover the bottom end of the inlet port . This is the inlet port opening (IPO) condition , make the mark on the flywheel and measure the distance from TDC 5. When piston moves from TDC to BDC observe when the bottom edge of the piston completely covers the inlet port . This is the inlet port closing (IPC) condition . Make the mark on the flywheel and measure the distance from TDC . 6. When the piston moves from TDC to BDC , observe , when the top edge of the piston just uncover the exhaust port . This is the exhaust port opening [EPO] condition . Make the mark on the flywheel and measure the distance from BDC . 7. When the piston moves from BDC to TDC , observe , when the piston completely cover the exhaust port ,. This is the exhaust port closing condition [EPC] . Make the mark on the flywheel and measure the distance from BDC . 8. When the piston moves from TDC to BDC observe, when the top edge of the piston just uncover the transfer port . This is the transfer port opening [TPO] condition . Make the mark on the flywheel and measure the distance from BDC 9. When the piston moves from BDC to TDC , observe , when the piston completely covers the transfer port. This is the transfer port closing [TPC] condition . Make the mark on the flywheel and measure the distance from BDC .

Note : 1. 2. 3.

The inlet port opening distance and closing distance from TDC are equal . The exhaust port opening distance and closing distance from BDC are equal . The transfer port opening distance and closing distance from BDC are equal .

Result :
The port timing diagram for the given two stroke cycle petrol engine was drawn.

You might also like