Code No: R161208 R16 SET - 1

I B. Tech II Semester Supplementary Examinations, March - 2022

ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PART –A
1. a) Polarities of voltages across three resistors in series are shown below. Determine (3M)
the potentials at the points a, b, c, and d.

b) List the properties of a tree in graph theory. (3M)

c) Explain the concept of Mutual Inductance. (2M)
d) At what frequency will the input current and the terminal voltage of an RLC series (2M)
circuit be in phase with each other?
e) Explain the concept of reactance, impedance, susceptance and admittance as (2M)
phasors.
f) State and explain Millman’s theorem. (2M)
PART -B
2. a) Explain the steps various involved in network reduction from Delta to Star. (7M)

b) Calculate the resistance across the terminal’s ab for the following network: (7M)

3. For the network shown below, draw the oriented graph and obtain the tie- set (14M)
matrix. Use this matrix to calculate ‘i’

4. a) Two coils of self-inductances L1 and L2 are mutually coupled. Derive the (7M)
expression for the net inductance of the coils if they are connected in parallel
opposing.
1 of 2

|''|'|''|''|''|||'|| www.manaresults.co.in
Code No: R161208 R16 SET - 1

b) Find the input impedance for the following circuit: (7M)

5. a) Analyze the phase relations in a pure resistor, pure inductor and pure capacitor (7M)
with necessary waveforms and related vector diagrams.

b) An inductive coil having a 30 resistance and unknown inductance is connected (7M)

in parallel with a 100 resistor. The combination is connected across a 100 V,
50 / Hz source. If the power delivered by the source is 400 W, find the value of
the inductance.

6. a) Find ‘C’ which results in resonance in the circuit shown in Figure below when (7M)
= 5000 rad/s.

b) Find the voltage VAB for the circuit shown below: (7M)

7. Solve for the current I in the circuit by superposition theorem. (14M)

2 of 2

|''|'|''|''|''|||'|| www.manaresults.co.in
Code No: R161208 R16 SET - 1
I B. Tech II Semester Regular/Supplementary Examinations, April/May - 2019
ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PART –A
1. a) Determine V in the circuit shown in figure 1(a). (2M)

10A 5Ω V 5A 5Ω 3A

Figure 1(a)

b) Draw the dual of the network shown in figure 1(b). (2M)

R1 R2
L
C
i

Figure 1(b)

c) A Coil of 100 turns is linked by a magnetic flux of 20mWb. If this flux is reversed (2M)
in a time of 2ms, calculate the average emf induced.
d) What is the average value for a resultant current having 10A of DC component (2M)
and 10A of peak value of AC Component.
e) Define selectivity and bandwidth of a series resonant circuit. (2M)
f) State Superposition theorem. (2M)
g) What are the uses of source transformation? (2M)

PART –B

2. a) Explain the star-delta transformation and delta-star transformation and derive the (7M)
expressions for equivalent resistances.

1 of 3

|''|'''||''||'''|||| www.manaresults.co.in
 Code No: R161208 R16 SET - 1

b) Find the power absorbed by each element in the circuit shown in figure 1(b). (7M)

5A 10ms 25ms 0.8ix

ix

Figure 2(b)

3. Find out currents through and voltages across all branches of the network shown (14M)
in figure 3, with the help of tie-set schedule.

2Ω 8V

4Ω 6Ω

6Ω 4Ω
2Ω

12V 6V

Figure 3
4. a) Two coupled coils with L1=0.01H and L2=0.04H and K=0.6 are connected in four (7M)
different ways i.e series aiding, series opposing, parallel aiding and parallel
opposing. Find the equivalent inductance in each case.

b) Explain the following terms: (7M)

(i) Reluctance (ii) mmf (iii) Co-efficient of coupling (iv) Magnetic flux density (v)
Magnetic field strength.

5. a) A Voltage v(t) =141.4 sin (314t+100) is applied to a circuit and a steady current (7M)
given by i(t) = 14.14 sin (314t-200) is found to flow through it. Determine: (i)
Power factor of the circuit (ii) Power delivered to the circuit. Also draw the phasor
diagram. i(t)
6A

0.06 0.10
O t sec
0.04
-2A

Figure 5(b)
2 of 3

|''|'''||''||'''|||| www.manaresults.co.in
 Code No: R161208 R16 SET - 1
b) A varying current, with a periodic waveform as shown in figure 5(b), flows (7M)
through an 8Ω resistor. Determine (i) mean value (ii) rms value (iii) heat
dissipated in the resistor in 5 minutes.

6. a) Show that the locus of current of a series circuit consisting of resistance and (7M)
inductance with resistance varied and inductance reactance fixed, when supplied
by a constant AC Voltage source, lies on circular path.
b) An RLC Series circuit consists of R=1kΩ, L=100mH, C=10µF. If a voltage of (7M)
100V is applied across the combination, determine resonant frequency, quality
factor and bandwidth.

7. a) Find the Thevenin’s equivalent circuit with respect to terminals A and B for the (7M)
network shown in figure 7(a).

O A
2Ω 4Ω - +
5Vx
+
2A
Vx
_ 2Ω

O B
Figure 7(a)

b) State and explain reciprocity theorem. Is this theorem valid for network with two (7M)
sources? Substantiate your answer.

3 of 3

|''|'''||''||'''|||| www.manaresults.co.in
www.manaresults.co.in
Code No: R161208 R16 SET - 2
I B. Tech II Semester Regular/Supplementary Examinations, April/May - 2019
ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PART –A
1. a) Find the equivalent resistance between terminals A-B of the network shown in (2M)
figure 1(a). i
A O
1Ω

2i 3Ω

BO
Figure 1(a)

b) Give the differences between an equivalent network and a dual network. (2M)
c) State Faraday’s law of electromagnetic induction. (2M)
d) The instantaneous value of emf is v =300 sin 800πt. What is the average value and (2M)
rms value of the emf?
e) In an AC Circuit, containing pure inductance, the voltage applied is 110V, 50Hz (2M)
while the current is 10A. What is the value of inductance in the Circuit?
f) State Millman’s theorem. (2M)
g) State KVL and KCL. (2M)
PART -B
2. a) Using source transformation, find the voltage V in the circuit shown in figure 2(a). (8M)
i V
O
50 Ω 100Ω

15 V
100 Ω
+ 10 i
-

Figure 2(a)
1 of 3

|''|'''||''||'''|||| www.manaresults.co.in
 Code No: R161208 R16 SET - 2

b) Explain the salient features of mesh and nodal analysis. (6M)

3. Draw the graph of the network shown in figure 3 and select a suitable tree to write (14M)
tie-set schedule. Also find the three loop currents.

1Ω 1Ω

+
1Ω 2Ω 2Ω
5V
-

Figure 3
4. a) Two coupled coils with self inductance L1=0.2H and L2=0.6H have a coupling co- (7M)
efficient K=0.6. The number of turns in coil 2 is 1000. If the current in coil 1 is
i1=10 sin 400t amperes, determine the voltage at coil 2 and maximum flux set up
by coil 1.
b) A rectangular shaped core is made of mild steel plate 15mm ×20mm cross-section. (7M)
The mean length of the magnetic path is 18cm. The exciting coil has 300turns and
0.7 amperes current. Calculate (i) magnetizing force (ii) flux density (iii)
reluctance (iv) flux of magnetic circuit. Assume relative permeability of mild steel
as 940.

5. a) A Series circuit of two pure elements has the following applied voltage and (7M)
resulting current, v =225 sin (300t+450), i=8.5 sin (300t+150). Find the elements
comprising the circuit. If the voltmeter, ammeter, wattmeter, frequency meter and
power factor meter are connected in the circuit, what will be their respective
readings.

b) Calculate the form factor for the saw-tooth waveform shown in figure 5(b). (7M)
i(t)

50A --------------------------------
--

t (sec)
O 4 8 12

Figure 5(b)
6. a) Find the resonance frequency for the parallel resonant circuit when RL and L are (7M)
connected in branch 1, and RC and C are connected in branch 2, and branch 1 and
branch 2 are connected in parallel to an alternating voltage source.
b) A series circuit with R=50Ω, L=0.1H, C=10µF has an applied voltage V=100 ∠0 0 . (7M)
Find maximum voltage across the inductor and the frequency at which it occurs.

2 of 3

|''|'''||''||'''|||| www.manaresults.co.in
 Code No: R161208 R16 SET - 2

7. a) Verify the reciprocity theorem using the network given in figure 7(a). (7M)

j4 Ω I
3Ω

100 ∠0 0 V ~ 10 Ω
5Ω -j5 Ω

Figure 7(a)

b) State and explain Superposition theorem. Is this theorem valid for power (7M)
calculations? Substantiate your answer.

3 of 3

|''|'''||''||'''|||| www.manaresults.co.in
www.manaresults.co.in
Code No: R161208 R16 SET - 3
I B. Tech II Semester Regular/Supplementary Examinations, April/May - 2019
ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PART –A
1. a) Find the equivalent resistance between terminals A-B in the network shown in (2M)
figure 1(a).
A
2Ω
3Ω
i 4i
B
Figure 1(a)

b) Explain the degree of a node with examples. (2M)

c) Define reluctance and permeance of a magnetic circuit. (2M)

d) A pure capacitor of 50µF offers a reactance of 50Ω against an AC supply of 100V. (2M)
What is the capacitor current and frequency of the supply?

e) An RLC series circuit consists of R=1kΩ, L=100mh, C=10µF. If a voltage of (2M)

100V is applied across the combination, what is the Quality factor and bandwidth
at resonance.
f) State Reciprocity theorem. (2M)
g) Define reactive power and complex power. (2M)

PART -B

2. a) Explain the source transformation with examples. (6M)

b) Use nodal analysis to determine V1 and power being supplied by dependent (8M)
current source in the circuit shown in figure 2(b).

50 Ω
V1
20 Ω 30 Ω
0.01V1
5A 0.5V1

Figure 2(b)
1 of 3

|''|'''||''||'''|||| www.manaresults.co.in
 Code No: R161208 R16 SET - 3

3. For a network shown in figure 3, derive the cutset matrix and find various branch (14M)
voltages and currents. 8Ω

3Ω 4Ω
4Ω
12V 24V

Figure 3
4. a) Two coils have a coupling co-efficient K=0.85 and coil 1 has 250 turns. The (7M)
current in coil 1 is 2A and total fulx is 0.3mWb. When the current i1 is reduced
linearly to zero in 2 milli-seconds, the voltage induced in the coil is 63.75V. Find
L1, L2, M and N2.

b) A Steel ring of 25cm mean diameter and of circular cross-section 3cm in diameter (7M)
has an air gap of 1.5mm length. It is wound uniformly with 750 turns of wire
carrying a current of 2.1A. Calculate (i) Magnetomotive force, (ii) Flux density in
air gap (iii) Magnetic flux (iv) relative permeability of steel ring (v) Total
reluctance. Assume that iron part takes about 35% of the total magnetomotive
force.

5. a) A Choke coil connected across a 250V, 50Hz supply takes a current of 10A at 0.8 (7M)
power factor lagging. What will be the power taken by the choke when connected
across 220V, 25Hz supply?
b) If the complex power S in branch (3+j6)Ω is 1500VA, what will be the indication (7M)
on the ammeter shown in figure 5(b). Also find the complete power information.
A
3Ω 3Ω

V
j3Ω j6Ω

Figure 5(b)

6. a) Explain the meaning of half-power frequencies and derive the expressions for a (7M)
series RLC Circuit.
b) A Coil of inductance 2H and resistance of 10Ω in series with condenser ‘C’ is (7M)
supplied at constant voltage from variable frequency. If the maximum current is
10A at 75Hz, find the value of C and also determine the frequency when the
current is 5A.

2 of 3

|''|'''||''||'''|||| www.manaresults.co.in
 Code No: R161208 R16 SET - 3

7. a) Using the principle of superposition, calculate the current through 4Ω resistor in (8M)
the network shown in figure 7(a).

5Ω 4Ω 2Ω

j2 Ω 100 ∠90 0
100 ∠0 0 V ~ -j2 Ω ~

Figure 7(a)

b) State and explain maximum power transfer theorem. What the applications and (6M)
limitations of this theorem.

3 of 3

|''|'''||''||'''|||| www.manaresults.co.in
www.manaresults.co.in
Code No: R161208 R16 SET - 4
I B. Tech II Semester Regular/Supplementary Examinations, April/May - 2019
ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PART –A
1. a) What is the value of V2 in the circuit shown in figure 1(a). (2M)
10 Ω
i
+ + V2 - 20 Ω +
80V
- 20 V
2V2
-

Figure 1(a)
b) What is meant by a planar circuit and a non-planar circuit? (2M)
c) Define fringing flux and leakage flux. (2M)
d) An RLC Series circuit has R=8Ω, XL=6.283Ω, XC=22.736Ω. What is the (2M)
impedance and power factor of the circuit?

e) What is a locus diagram? What are the benefits with locus diagram? (2M)
f) State compensation theorem. (2M)
g) What is meant by lagging and leading power factors? (2M)
PART -B

2. a) State and explain the Kirchhoff’s current and voltage laws with suitable examples. (6M)
b) Determine the voltage across 3Ω resistor using mesh analysis for the circuit shown (8M)
in figure 2(b).

6Ω

8V 2A
3Ω
5Ω
12V

Figure 2(b)
1 of 3

|''|'''||''||'''|||| www.manaresults.co.in
 Code No: R161208 R16 SET - 4

3. For the network shown in figure 3, obtain the oriented graph of the network and (14M)
write the cut-set schedule of the graph and determine loop currents.

0.5Ω 1Ω

10 A 0.5Ω 1Ω 0.25Ω

Figure 3

4. a) The combined inductance of two coils connected in series is 0.6 or 0.1 depending (7M)
on the relative directions of the coils. If one of the coil when isolated has a self
inductance of 0.2H, calculate (i) mutual inductance, (ii) Co-efficient of coupling.
b) An iron ring, cross-sectional area of 5cm2 and mean length 100cm, has an air-gap (7M)
of 2cm cut in it. Threee separate coils having 100, 200, and 300 turns are wound
on the ring and carry currents of 1A, 2.5A and 3A respectively such that they
produce additive fluxes in the ring. Relative permeability of the ring material is
1000. Calculate the flux in the air gap.

5. a) A resistance and an inductance are connected in series across 250V, AC supply. (6M)
When the frequency is 40Hz, the current is 1.9A and when the frequency is 50Hz,
the current is 1.7A. Determine (i) resistance and inductance of the circuit (ii)
power factor of the circuit at 50Hz (iii) power consumed at 50Hz.
b) The impedance of a circuit is (6+j8)Ω and an applied phasor voltage is V=50 (4M)
∠45 0 Volts. Determine the power triangle values.

c) What is meant by the rms value of an ac quantity? Explain its practical (4M)
importance.

6. a) A Series RLC Circuit with L=25mH and C=70µF has a lagging phase angle of 200 (7M)
at ω=2000 rad/sec. At what frequency will the phase angle be 300 leading?
b) Obtain values of R, L and C in series RLC Circuit that resonants at 1.5kHz and (7M)
consumes 50W from a 50V AC source operating at resonant frequency. The
bandwidth is 0.75kHz.

2 of 3

|''|'''||''||'''|||| www.manaresults.co.in
 Code No: R161208 R16 SET - 4

7. a) Find the value of RL to be connected between terminals AB in figure 7(a), for (7M)
maximum transfer of power and maximum value of power.
0
ix A
10ix
0.9A
+
3Ω RL
16V
_

2Ω B
o
Figure 7(a)

b) State and explain thevenin’s theorem. Also explain the limitations of this theorem. (7M)

3 of 3

|''|'''||''||'''|||| www.manaresults.co.in
Code No: R161208 R16 SET - 1

I B. Tech II Semester Regular Examinations, April/May - 2017

ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

PART –A
1. a) State Kirchhoff’s laws. (2M)
b) List out different dual elements for basic electrical elements. (2M)
c) What is Faraday’s law of electromagnetic induction? (2M)
d) What is the difference between instantaneous power and complex power? (2M)
e) What is the significance of quality factor in series resonant circuit? (2M)
f) State Norton’s theorem. (2M)
g) A series RLC circuit has a resonant frequency of 12 kHz. If R=5 ohms and XL=300 (2M)
ohms at resonance, what is the bandwidth.

PART –B

2. a) Distinguish between independent and dependent sources. (4M)

b) A triangular wave is shown in Figure 1. It is applied to R, L and C individually. (10M)
Estimate the current in each element.
v(t)
V
3T/4
0 t (sec)
T/4 T/2 T
-V
Figure 1

3. a) Explain the concept of duality between two electrical networks. Clearly distinguish (5M)
between equivalent and dual network.
b) Find and draw the maximum possible number of trees for the network shown in (9M)
Figure 2. 1Ω Vx
+ -
+ -
Vx
+ 3A
18 V 6Ω
-

Figure 2

1 of 2
WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
Code No: R161208 R16 SET - 1

4. a) Explain the dot convention in coupled circuits. (4M)

2
b) The air gap in a magnetic circuit is 1.5 mm long and 2500 mm in cross sectional (5M)
area. Calculate (i) the reluctance of the air gap (ii) the MMF required to set up a
flux of 800x10-6 Wb in the air gap.
c) A mild steel ring having a cross sectional area of 500 m2 and a mean circumference (5M)
of 400 mm has a coil of 200 turns wound uniformly around it. Calculate: (i) the
reluctance of the ring and (ii) the current required to produce a flux of 800 µ Wb in
the ring. Assume that µr is 380.

5. a) A 20 ohms resistance and 30 mH inductance are connected in series and the circuit (7M)
is fed from 230 V, 50 Hz AC supply. Find (i) Inductive reactance and total
impedance (ii) current in the circuit (iii) voltage across resistance and inductance
(iv) real, reactive and apparent power (v) Power factor.
b) Calculate RMS value, average value, form factor for the saw waveform shown in (7M)
Figure 3. i (t)
50A

0 t (sec)
2 4 6
Figure 3

6. a) A variable frequency source of V=200 volt is applied to a series R-L circuit having (7M)
R=5Ω and L=5 mH. Draw I-locus considering sample frequencies
ω=0,500,1000,2000 and 5000 rad/sec.
b) Show that the locus of current of a series circuit consisting of resistance and (7M)
inductance with resistance varies and inductive reactance fixed, when supplied by a
constant ac voltage source, lies on a circular path.

7. a) State and explain Maximum Power Transfer theorem. (7M)

b) Verify the reciprocity theorem for the following circuit shown in Figure 4. (7M)
I2
I1 4Ω
0
10∠0 I 5Ω
-j4 Vx

Figure 4

2 of 2
WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
Code No: R161208 R16 SET - 2

I B. Tech II Semester Regular Examinations, April/May - 2017

ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

PART –A
1. a) What are the uses of source transformation? (2M)
b) What are the properties of a tie-set matrix? (2M)
c) Define MMF and reluctance. (2M)
d) What is the significance of power factor in AC circuits? (2M)
e) What is a locus diagram? (2M)
f) State reciprocity theorem. (2M)
g) What is the quality factor of a coil of R=10 ohms, L=0.1 H, C=0.1 µF? (2M)
PART -B
2. a) The current is 15 mH inductor can be expressed as i(t)=(2-e-1000t) mA. Find (i) (7M)
voltage across the inductor (ii) instantaneous power.
b) Two groups of resistances, one consisting of 4 ohms, 6 ohms and 12 ohms in (7M)
parallel and other consisting of 3 ohms and 6 ohms in parallel are connected in
series with a source of 10 V having an internal resistance of 1 ohm. Calculate the
resistance of entire circuit, the potential drop across each group and current in each
resistance.

3. Find out currents through and voltages across all branches of the network shown in (14M)
Figure 1, with the help of its tie-set schedule.
2Ω 8V
+-

12 V +- 4Ω 6Ω + 6V
-
2Ω
6Ω 4Ω

Figure 1

1 of 2

WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
Code No: R161208 R16 SET - 2

4. a) Derive an expression for co-efficient of coupling in a magnetic circuit. (5M)

b) Explain Faradays Laws of Electro magnetic Induction. (3M)
c) Two coils having 750 and 1200 turns, respectively, are wound on a common non- (6M)
magnetic core. The leakage flux and mutual flux, due to a current of 7.5A in coil 1,
is 0.25 mWb, and 0.75 mWb, respectively. Calculate: i) Self Inductance, ii) Mutual
Inductance, iii) coefficient of coupling.

5. a) A voltage of 200 V is applied to a series circuit consisting of a resistance, a choke (7M)

coil and a capacitance. If the respective voltages across these components are 170
V, 150 V and 100 V. The current in the circuit is 4 A. Find the power factor of the
circuit.
b) A time varying current, with a periodic wave form is shown in Figure 2, flows
through an 8W resistor. Determine (i) mean value (ii) rms value (iii) heat (7M)
dissipated in 5 minutes. i (t)
6A

0.06 0.1
0
0.04 t (sec)
-2A
Figure 2

6. a) For a given series RLC circuit with R=120Ω, L=0.6H and C=70µF, Calculate the (7M)
resonance, lower and upper half power frequencies.
b) Show that the resonant frequency ω0 of an RLC series circuit is the geometric (7M)
mean of ω1and ω2, the lower and upper half-power frequencies respectively.

7. a) State and explain Millman’s theorem. (6M)

b) Find Thevenin’s and Norton’s equivalent circuits for the network shown in Figure
3. (8M)
ia + - a
2Ω +
10 ia
4Ω 5A
50V

-b
Figure 3

2 of 2
WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
Code No: R161208 R16 SET - 3

I B. Tech II Semester Regular Examinations, April/May - 2017

ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

PART –A

1. a) What are the differences between dependent and independent sources? (2M)
b) What are the properties of a cut-set matrix? (2M)
c) What is the significance of coefficient of coupling in magnetic circuits? (2M)
d) Draw the power triangle and represent real, reactive power and apparent power. (2M)
e) Define bandwidth and selectivity. (2M)
f) State superposition theorem. (2M)
g) A series circuit has R=4 ohms, L=25 mH, and C=150 µF. What is the bandwidth? (2M)

PART –B

2. a) State and explain KVL and KCL with an example. (5M)

b) Draw the waveforms for iR, iL, iC for the circuit shown in Figure 1, when it is (9M)
excited by a voltage source having a waveform shown in Figure 2.
v(t)

v(t) C 10 V
R L
0 t (sec)
2 4 6
-10 V
Figure 1 Figure 2

3. a) What is duality? Explain the procedure to obtain the dual of the given planar (6M)
network.
b) Find the current in each branch and voltage across each branch of the network (8M)
shown in Figure 3, using tie-set schedule.

1Ω 1A
2A 3Ω 2Ω 5A

Figure 3

1 of 2

WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
Code No: R161208 R16 SET - 3

4. a) Prove that for series magnetic circuit having different reluctance segments, total (4M)
reluctance will be the sum of individual reluctances.
b) Define (i) self inductance (ii) mutual inductance (iii) MMF(vi)Flux (v) Reluctance (4M)
c) Two coils have a mutual inductance of 0.4 H, if the current in one coil is varied (6M)
from 4A to 2A in 0.5sec, calculate (i) The average e.m.f induced in the second coil
(ii) The rate of change of flux linked with the second coil assuming that it is
wound with 300 turns.

5. a) A coil of power factor 0.9 is in series with a 120 µF capacitor. When the circuit is (7M)
connected to a 50 Hz supply, the potential difference across the coil is equal to the
potential difference across the capacitor. Find the resistance and inductance of the
coil.
b) Find the RMS value and average value of the waveform shown in Figure 4. (7M)
v (t)
10V
2 4
0
1 3 t (sec)
-10V
Figure 4

6. a) A coil of 2.2Ω resistance and 0.01H is connected in series with a capacitor across (7M)
220V mains. Find the value of capacitance such that the maximum current flows
in the circuit at a frequency of 100Hz. Also, find the current and voltage across the
capacitor.
b) Find C which results in resonance in the circuit shown in Figure 5, when (7M)
ω=5000rad/s.
8Ω 8Ω

j6 Ω C

Figure 5
7. a) State and explain Norton’s theorem. (6M)
b) Using Thevenin’s theorem, find the current flowing through 1.5 ohms resistance (8M)
between A and B for the network shown in Figure 6.

9Ω
A
6Ω 7.5 Ω
1.5 Ω 5Ω 30 V

B
Figure 6

WWW.MANARESULTS.CO.IN
2 of 2

|''|'''||''||'''||||
Code No: R161208 R16 SET - 4
I B. Tech II Semester Regular Examinations, April/May - 2017
ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

PART –A

1. a) Write the V-I relations of R, L and C parameter. (2M)

b) What are the properties of a tree in electrical circuits? (2M)
c) Write the analogy between electrical and magnetic circuits. (2M)
d) Define average value and form factor. (2M)
e) What is the difference between series and parallel resonance? (2M)
f) State compensation theorem. (2M)
g) Give the differences between tie-set and cut-set. (2M)

PART –B

2. a) Explain the star – delta and delta – star transformation by deriving relevant (6M)
expressions.
b) Find the current through each branch of the circuit shown in Figure 1, using mesh (8M)
analysis.
5Ω 10 Ω
+ 2Ω
30 V + 6Ω
- V1
- 3V1 +- +
15 V
-
Figure 1

3. For the given network shown in Figure 2, obtain the oriented graph of the network. (14M)
Write the cut-set of the graph and determine the loop currents.

0.5 Ω 1Ω
10 A 0.5 Ω 1Ω
0.25 Ω

Figure 2

1 of 2

WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
Code No: R161208 R16 SET - 4

4. a) The number of turns in two coupled coils are 600 and 1700, respectively. When a (7M)
current of 6A flows in coil 2, the total flux in this coil is 0.8 mWb, and the flux
linking the first coil is 0.5mWb. Calculate L1, L2, M and K.
b) Two coils with a coefficient of coupling of 0.6 between them, are connected in (7M)
series so as to magnetize i) in one combination in the same direction and ii) in
another combination in the opposite direction. The corresponding values of
equivalent inductance are 1.8 H and 0.8 H respectively. Find the self inductance of
the two coils and the mutual inductance between them.

5. a) A coil having a resistance of 10 ohms and an inductance of 0.2 H is connected in (7M)

series with a 100 µF capacitor are fed with 230 V, 50 Hz AC supply. Calculate (i)
active and reactive components of current (ii) voltage across the coil. Draw the
phasor diagram.
b) Find the rms and average value of the trapezoidal waveform shown in Figure 3. (7M)
v(t
50V

0
1 2 3 4 5 6 t (sec)
1 Cycle Figure 3

6. a) A constant inductance L is in parallel with a series R-C circuit in which R varies (7M)
from zero to infinity. This combination is connected to a constant voltage, constant
frequency supply. Show that the circuit takes a constant current from the source at
all power factors between zero lagging and zero leading, if Xc=XL/2 . Draw the
relevant locus diagram.
b) An inductive coil having a resistance of 30 ohm and inductance of 0.03H is (7M)
connected in series with 0.03 µF capacitor. Calculate i) Q of the coil ii) Resonant
frequency and iii) the half-power frequencies.

7. a) State and explain Thevenin’s theorem. (6M)

b) Use superposition theorem to find v0 in Figure 4. (8M)

3Ω 7 iβ

iβ +
6A 25 Ω v0
-
Figure 4

2 of 2
WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
Code No: R161208 R16 SET - 1
I B. Tech II Semester Regular/Supplementary Examinations, April/May - 2018
ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical
Electrical and Electronics Engineering
Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A
( and Part-B)
Part
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PART –A
1. a) State and explain Kirchoff’s Laws.
Laws (3M)
b) Define the following terms with example (2M)
(i) Graph of a network
(ii) Oriented graph
c) Find the effective value of the inductance for the following connections as shown (3M)
in figure 1(c).

Figure 1(c)
d) Calculate the current drawn by impedance. Z = (30- (30 j70) Ω when voltage, V = 120 (2M)
0
∠0 is applied across it.
e) A series RLC circuit has the following parameter values R = 10 Ω, L = 0.01 H and (2M)
C = 10 µF.
F. Find the Q factor of the circuit at resonance.
f) Is super position valid for power? Substantiate your answer
answer. (2M)
PART –B
2. a) In the network shown in figure 2(a), determine the voltage Vb which results in a (9M)
zero current through the (2+j3) Ω impedance branch.
j3 Ω
5Ω 2Ω 4Ω

30 j5 Ω 6Ω Vb

Figure 2(a)
b) Determine the voltage V using source transformation
transformation and simplification for the (5M)
circuit shown in figure 2(b).
2(b)

3Ω 4Ω +
8V
6A V
3Ω 6Ω
__
www.ManaResults.co.in
Figure 2(b)
1 of 3
 Code No: R161208 R16 SET - 1

3. a) For the network shown in figure 3(a), draw the graph and write a tie--set schedule. (10M)
Using the tie-set
set schedule obtain the loop equations.
equations

Figure 3(a)
b) For the network shown in figure 3(b), draw the graph and show some possible trees.
trees (4M)

R1 R2 C1

L1 R3
V I

Figure 3(b)
4. a) A cast steel ring is wound with 500 turns. The cross – section of the core is 2 x 10-3 (8M)
m2 and the mean length is 0.16m. (a) Find value of I required to develop a magnetic
flux of φ = 4x 10-4 wb. (b) Determine the values of µ and µr for the material under
these conditions. Assume H for cast steel = 170 At/m.
b) Draw the dotted equivalent circuit for the net work shown in below figure
fig 4(b). and (6M)
find the equivalent inductive reactance.

Figure 4(b)

5. a) Two coils of impedance 25.23 ∠ 370 and 18.65 ∠ 680 ohms are connected
nnected in series (7M)
across a 230V, 50Hz
Hz supply. Find the total impedance, current, power factor, and
active power.
b) Determine the rms value of a triangular wave in which the average rises uniformly (7M)
from 0 to V volts and completes the cycle by falling instantaneously to zero.
www.ManaResults.co.in
2 of 3
 R16 SET - 1
Code No: R161208

6. a) For the circuit shown in figure 6(a). (7M)

(i) Determine the KVL equations.
(ii) Find the two loop currents I1 , and I2
(iii) Find the power supplied by the source and the power dissipated in each resistor.
-j5Ω
2Ω -j2Ω 3Ω

+
j2Ω 1Ω
0
10 ∠0 V -

Figure 6(a)

b) A coil of 20 ohm resistance and an inductance of 0.2 H are connected in parallel (7M)
with a capacitor of 100 µF. Determine the resonant frequency and the input
impedance at resonance.

7. a) State and explain compensation theorem. (7M)

b) Find the value of R in the circuit shown in figure 7(b) such that maximum power (7M)
transfer takes place. What is the amount of this power?
1Ω 5Ω R

+ -
4V 2Ω 1Ω 6V
- +

Figure 7(b)

3 of 3

www.ManaResults.co.in
Code No: R161208 R16 SET - 2
I B. Tech II Semester Regular/Supplementary Examinations, April/May - 2018
ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical
Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A
( and Part--B)
question in Part-A is Compulsory
2. Answering the questions
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PART –A
1. a) Explain source transformation technique.
technique (2M)

b) Define the following terms

terms. (3M)
(i) Graph of the Network and Sub graph.
(ii) Rank of graph.

c) Find the effective value of the inductance for the following connections as shown (2M)
in figure 1(c).

Figure 1(c)

d) A current I = 10∠300 flows through an impedance, Z = 20∠

20 - 220 Ω find the (2M)
average power delivered to the impedance
impedance.
ries circuit has a current of 4 cos (200t + 13.20) amp flowing
e) A two element series (3M)
when the voltage of 200 sin (2000t+500) volts is applied across its terminals.
Determine the values of elements.
f) State Maximum power transfer theorem.
theorem (2M)
PART -B
2. a) Determine the node voltages V1,
V1 V2, and V3for the circuit shown in figure
ure 2(a). (7M)

figure 2(a)
www.ManaResults.co.in
1 of 4
 Code No: R161208 R16 SET - 2

b) Write the loop equations of the circuit as shown in figure 2(b) and find the voltage (7M)
Vx.
j2Ω 5 ∠30 0 (V)
2Ω
Ω

10 ∠0 0 (V) j5Ω 10Ω

2Ω
Ω 2Ω j2Ω

10Ω

V
Figure 2(b)
3. a) From figure 3(a), make the graph and find one tree. How many mesh currents are (9M)
required for solving the network? Find the number of possible trees.

Figure 3(a)

b) Determine the basic cut set matrix for the oriented graph given as shown figure (5M)
3(b) where in the elements 1, 2, 3 are tree branches.

Figure 3(b)

4. a) A rectangular core has a cross-sectional

cross area of 20 cm2. It is made from two (7M)
materials: cast steel 50 cm and steel 40 cm long. It is desired to create a flux of 3
mWb in the core. The relative permeability for cast steel is 500 and that of sheet
steel is 2000. The coil has 300 turns. Find mmf and current in the coil.

2 of 4
www.ManaResults.co.in
 Code No: R161208 R16 SET - 2

b) Write down the voltage equation for the following figure 4(b),, and determine the (7M)
effective inductance.

Figure 4(b)
5. a) The following circuit shown
show in figure 5(a) is a parallel RL arrangement
rrangement connected (7M)
across 200V, 50Hz
Hz ac supply calculate
calculate.
(i) The current drawn from supply
(ii) Apparent power
(iii) Real power, and
(iv) Reactive power

Figure 5(a)
b) Determine the rms value of a saw tooth wave as shown in figure 5(b). (7M)

Figure 5(b)
6. a) A series RLC circuit consists of resistance R = 20 Ω, inductance, L= 0.01H and (7M)
capacitance, C= 0.04µF
µF. Calculate the frequency at resonance. If a 10 Volts of
frequency equal to the frequency of resonance is applied to this circuit, calculate
the values of VC and VL across C and L respectively. Find the frequencies at which
these voltages VC and VL are maximum? .

3 of 4

www.ManaResults.co.in
 Code No: R161208 R16 SET - 2

b) For the series circuit shown in figure 6(b), evaluate the value of reactance when (7M)
the power factor is 0.866 lag using locus diagram.
diagram

Figure 6(b)

7. a) Find the current flowing in the resistor R4 of the network shown in figure
ure 7(a).
7(a) If a (7M)
resistance of 0.5 Ω is inserted in series with R4, find, using the compensation
theorem, the current that will flow through R4’
R1=4Ω R3=8Ω

R2=16Ω R4=8Ω
12V

Figure 7(a)

b) Calculate the voltage V across the resistor R by using the superposition theorem as (7M)
shown in figure 7(b).

Figure 7(b).

4 of 4
www.ManaResults.co.in
 R16 SET - 3
Code No: R161208
I B. Tech II Semester Regular/Supplementary Examinations, April/May - 2018
ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical
Electrical and Electronics Engineering
Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A
( and Part--B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PART –A
1. a) Distinguish between independent and dependent sources. (3M)

b) Draw the dual of the network shown in figure 1(b). (3M)

Figure 1(b)

c) Explain the dot convention used in magnetically coupled circuits. (2M)

d) Find the response “I” of an RL series circuit if R = 2Ω,
2 , L = 1H and the input (2M)
voltage, v(t) = 10 sin 3t..
e) Bring out the differences between series and parallel resonance
resonance. (2M)
f) Obtain the Norton’ss equivalent circuit with respect to the terminals AB for the (2M)
network shown in figure
ure 1(f).

Figure 1(f)

1 of 4

www.ManaResults.co.in
 Code No: R161208 R16 SET - 3

PART –B
2. a) Determine the current through 10-Ω
10 resistance in the network shown in fig
figure 2(a) (7M)
by using star-delta conversion.
conversion
4Ω
Ω 24Ω 13Ω

8Ω 12Ω 30Ω 17Ω

Ω
10Ω

12Ω
Ω 30Ω
+ -

180V
Figure 2(a)

b) Write the mesh equation for the circuit shown in figure 2(b) and determine the (7M)
currents I1, I2 and I3.

20V 4Ω
3Ω
20A
I1 I2 I3
2Ω

Figure 2(b)

3. a) Forr the graph shown in figure

fig 3(a) select a tree, identify the tie-sets
sets and write the (7M)
tie-set matrix.

Figure 3(a)

www.ManaResults.co.in
2 of 4
 Code No: R161208 R16 SET - 3
b) Draw the graph of the network shown in figure
fig 3(b) and write the incidence (7M)
matrix.

Figure 3(b)

4. a) A rectangular core has a cross-sectional

cross area of 20 cm2. It is made from two (7M)
materials: cast steel 50 cm and steel 40 cm long. It is desired to create a flux of 3
m wb in the core. The relative permeability for cast steel is 500 and that of sheet
steel is 2000. Thee coil has 300 turns. Find mmf and current in the coil.

b) Find the effective value of the inductance for the following connection shown in (7M)
figure 4(b).

Figure 4(b)
5. a) Calculate the average and rms value for a half-wave
half wave rectified sinusoidal quantity (7M)
as shown in figure 5(a)..

Figure 5(a)
www.ManaResults.co.in
3 of 4
 Code No: R161208 R16 SET - 3
b) Determine the total current supplied by the mains
m for the network shown in figure (7M)
5(b).

Figure 5(b)
6. a) A series RLC circuit is connected to a constant voltage variable frequency source (7M)
of 200 V (rms). The values of R, L and C are 5 Ω. 0.1 H and 100 µF. What would
be the voltage across C at resonance?
b) For the following circuit shown in figure 6(b), find the node voltages VA and VB (7M)
using node voltage method. The source current is given as Is(t) = 10 cos ωt(A), ω
= 100 rad/s.

Figure 6(b)
7. a) Find the value of R in the circuit shown in below figure 7(a) such that maximum (7M)
power transfer takes place. What is the amount of this power?
1Ω 5Ω R

+ -
4V 2
2Ω 1Ω 6V
- +

Figure 7(a).
b) Find Thevenin’s equivalent about AB for
fo the circuit shown in figure 7(b).
7(b) (7M)
VS
4Ω
+ -- A
2Ω
2Ω
4Ω
10V
4 VS

B
Figure 7(b).
www.ManaResults.co.in 4 of 4
Code No: R161208 R16 SET - 4
I B. Tech II Semester Regular/Supplementary Examinations, April/May - 2018
ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical
Electrical and Electronics Engineering)
Engineering
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A
( and Part--B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PART –A
1. a) Explain the volt ampere relationships for R,L and C parameters.
parameters (2M)
b) Determine the basic cut set matrix for the oriented graph given figure 1(b) where (3M)
in the elements 1,2,3 are tree branches
branches.

Figure 1(b)
c) Explain the dot connection used in magnetically coupled circuits (mutual (2M)
inductances) with the help of suitable examples.
d) Explain the concept of phase angle and phase difference. (3M)
e) Two coils of impedance 25.23 ∠ 370 and 18.65 ∠ 680 ohms are connected
nnected in series (2M)
across a 230V, 50Hz
Hz supply. Find the total impedance.
impedance
f) State Thevenin’s theorem.
theorem (2M)
PART –B
2. a) Use nodal analysis to find the voltages VA, VB, and VC for the circuit shown in (7 M)
figure 2(a), in which I1 = 0.4A.
0.4A
0.03 VX

VA VX VB
+ C
20 Ω 40 Ω
ly

l1 100 Ω 40 Ω 80 ly +

www.ManaResults.co.in
Figure 2(a)
1 of 4
 Code No: R161208 SET - 4
R16
b) (7M)
Determine the current through 10-Ω resistance in the network shown in figure 2(b)
by using star-delta conversion.

4Ω 24Ω 13Ω

8Ω 12Ω 30Ω 17Ω

10Ω

12Ω 30Ω
+ -

180V
Figure 2(b)

3. a) For the network shown in figure 3(a) draw the graph and show some possible (7M)
trees.

R1 R2 C1

V L1 R3
I

Figure 3(a)

b) Obtain the fundamental cut set matrix by choosing a suitable T (1,6,7) of the given (7M)
graph shown in figure 3(b).

Figure 3(b)
4. a) A coil of 500 turns is wound uniformly over a wooden ring having a mean (7M)
circumference of 50 cm and a cross sectional area of 500 mm2. If the current
through the coil is 3 A, calculate
(i) The magnetic field strength
(ii) The flux density and
(iii) The total flux

2 of 4
www.ManaResults.co.in
 Code No: R161208 SET - 4
R16
b) Determine the coupling coefficient and the energy stored in the coupled circuits at (7M)
t=1.5 s as shown in figure 4(b).

Figure 4(b)

5. a) Find the voltage Vx if, V1 (t) = 20cos 1000t volts and V2 (t) = 20sin 1000t volts as (7M)
shown in figure 5(a).

Figure 5(a)

b) Calculate the average power absorbed by the resistor and inductor. Find the (7M)
average power supplied by the voltage source for the circuit shown in fig
figure 5(b).

Figure 5(b)
6. a) In a series resonant network R = 6 ohm. The resonant frequency 0.5 MHz and the (7M)
band width is 105 rad/sec. Compute L and C of the network.

3 of 4
www.ManaResults.co.in
 Code No: R161208 SET - 4
R16
b) A coil of 10 ohms resistance and 0.1 H inductance is connected in series with a (7M)
150 µ F capacitor and the combination is energized with 240 V, 50 Hz supply as
shown in figure 6(b).. Calculate
(i) The current drawn from the mainstream
(ii) The voltage across the inductor coil and
(iii) The average power consumed and the power factor of the circuit

Figure 6(b)
7. a) In this circuit shown in figure 7(a), find voltage V, interchange the current source (7M)
and resulting voltage V and show that the reciprocity theorem is verified
verified.

I1 I2
2Ω
j5Ω
5 ∠90 0 (A)

-j2Ω
5Ω V

Figure 7(a)

b) Find the current I in the circuit shown in figure

fig 7(b) using the superposition (7M)
theorem.
1Ω
I

2Ω
1Ω 3Ω
1A 1V

Figure 7(b)

www.ManaResults.co.in
4 of 4
Code No: R161208 R16 SET - 1

I B. Tech II Semester Supplementary Examinations, July/August - 2021

ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

PART –A
1. a) State and explain Kirchhoff’s Current law. (2M)
b) Write the relation between Twigs and links w.r.t graph theory. (2M)
c) Distinguish between a Series and a parallel magnetic circuit. (2M)
d) Two circuit elements in a series connection have current and total voltage (2M)
i = 4 cos (2000t +13.20)A and v =160 sin (2000t + 500) V. Identify the two
elements and also find their values.
e) Explain the concept of bandwidth for a series RLC circuit. (2M)
f) Explain what happens to the resonant frequency in a series RLC circuit, if C is (2M)
increased.
g) In a series RLC circuit VR = 20V, VL = 25V and VC = 40V. What is the Source (2M)
voltage.

PART -B
2. a) Explain the procedure to calculate the Star to Delta transformations. (7M)

b) Find the current I1 for the following circuit.

(7M)

3. a) List and explain the properties of incidence matrix. (7M)

1 of 2

|''|'|''|''|''|||'|| www.manaresults.co.in
Code No: R161208 R16 SET - 1

b) Draw the dual network for the following network (7M)

4. a) Define the following Terms: (7M)

i) Self Inductance ii) Mutual Inductance
ii) Coupled Coils iv) Coupling Coefficient
b) Two identical coupled coils have an equivalent inductance of 100 mH when (7M)
connected series aiding, and 30 mH in series opposing. Find L1, L2, M, and k.
5. a) Explain the following terms: (7M)
i)RMS value ii)Average Value iii) Peak factor iv) Form factor
b) Find the rms value for the voltage waveform given below. (7M)

6. a) Explain the behavior of voltages and currents in parallel RLC resonant circuits. (7M)
b) (7M)
A series RLC circuit consists of R =25 , L =0.02 H and C =0.06µF. Calculate the
frequency at resonance. Ifa 25 Volts of frequency equal to the frequency of
resonance is applied to this circuit, calculate the values of voltage across C and L
respectively. Find the frequencies at which these voltages are maximum?
7. a) State and explain maximum power transfer theorem. (7M)
b) Compute the current in the 23- ohm resistor by applying Super position theorem. (7M)

2 of 2
|''|'|''|''|''|||'|| www.manaresults.co.in
Code No: R161208 R16 SET - 1

I B. Tech II Semester Supplementary Examinations, Nov/Dec - 2017

ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

PART –A
1. a) What are dependent Sources and write their symbols. (2M)

b) Draw a Graph for an electrical network. (2M)

c) Explain the concept of Mutual Inductance. (2M)
d) Transform the following sinusoid into Phasor (2M)
I = 5cos(ωt-750).
e) What is resonance in an ac series circuit? (2M)
f) State Reciprocity theorem. (2M)
g) A series audio circuit is shown in below figure .What is the impedance of the (2M)
circuit?
-j 20 Ω j 30 Ω
120 Ω

250 Hz -j 20 Ω

PART –B
2. a) Calculate the effective resistance between the points A and B in the circuit shown (7M)
in below figure.

WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
 Code No: R161208 R16 SET - 1

b) Using nodal analysis, determine the voltage between the points, P and Q shown in (7M)
below figure.
2A

P Q
2Ω 4Ω
10 V

8Ω 6Ω

3. a) Draw the graph of the network shown in below figure and write down the tie-set (7M)
matrix.

b) Construct the dual of the network shown in below figure. (7M)

R R

1V C R0 R1

4. a) A magnetic circuit consists of an iron ring of mean circumference 90 cm with (7M)

cross-sectional area of 10 cm2 throughout. A current of 2.5 A in the magnetizing
coil of 250 turns produce a total flux of 1.2 mwb in the iron. calculate:
(i) the flux density in the iron
(ii) the absolute and relative permeability of iron
(iii) the reluctance of the circuit.
b) Two coupled coils have self inductances L1=10mH and L2= 20mH. The (7M)
coefficient of coupling (K) being 0.75 in the air, find voltage in the second coil
and the flux of first coil provided the second coil has 500 turns and the circuit
current is given by i1 = 2 sin314t A.
WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
 Code No: R161208 R16 SET - 1

5. a) A variable frequency source of v = 200 volt is applied to a series RL circuit having (9M)
R=10 Ω and L=10 mH. Draw Z-locus and I-locus considering sample frequencies
ω=0,500,1000,2000 and 5000 rad/sec.
b) If voltage υ = 20 sin ( 100t + 40˚) is applied to a 60 µF capacitor, calculate the (5M)
current through the capacitor.

6. a) At resonance, the current is maximum in a series circuit and minimum in a parallel (6M)
circuit. Why?
b) A resistance of 12 Ω and an inductance of 0.025 H are connected in series across a (8M)
50Hz supply. What values of resistance and inductance when connected in parallel
will have the same resultant impedance and pf ? Find the current in each case
when the supply voltage is 230 V.

7. a) Using Norton’s theorem, find the equivalent circuit to the left of the terminals in (7M)
the circuit of below figure. Then find I.
6Ω 6Ω
a
l

12 V 2A 4Ω 1Ω

b) In the network shown in below figure, the 5 Ω resister is changed to 8 Ω . (7M)

Determine the resulting change in current through the (3+j4) Ω impedance branch
using compensation theorem.

WWW.MANARESULTS.CO.IN
3 of 3
|''|'''||''||'''||||
Code No: R161208 R16 SET - 1
I B. Tech II Semester Supplementary Examinations, Nov/Dec - 2018
ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PART –A
1. a) What are the applications and advantages of parallel circuits? (2M)
b) What are the properties of tie-set matrix? (2M)
c) State Ohm’s law for magnetic circuits and write its expression in terms of (2M)
magnetic quantities.
d) π (2M)
The instantaneous value of emf is V = 300 sin( 80 t ) Volts. Determine average
4
value and periodic time.
e) A series RLC circuit has a resonant frequency of 12 kHz. If R=5 ohms and XL at (2M)
resonance is 300 ohms, find the bandwidth.
f) Write the properties of series resonance. (2M)
g) State Compensation theorem. (2M)
PART -B
2. a) Explain about dependent and independent sources with examples. (6M)
b) Use nodal analysis to determine V1 and power being supplied by the dependent (8M)
current source in the circuit shown in Figure 2(b). All the values of resistances in
the circuit are in ohms.

50
V1 V2 V3
20 30
+
+ 0.5V1 0.01V1
5A
-
-

Figure 2(b)
3. a) For the network shown in figure 3(a), obtain the oriented graph of the network. (8M)
Write the cut-set matrix of the graph and determine the loop currents. All the
values of resistances in the circuit are in ohms.

0.5 1
10A 0.5 1 0.25

Figure 3(a)
WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
 1 of 2
Code No: R161208 R16 SET - 1

b) Explain the procedure for obtaining fundamental tie-set matrix of given network. (6M)

4. a) A coil of 200 turns is wound uniformly over a wooden ring having a mean (6M)
circumference of 600 mm and a uniform cross sectional area of 500 mm2. If the
current through the coil is 4 A, calculate:
(i) magnetic field strength,
(ii) flux density, and (iii) total flux.

b) Explain the importance of dot convention in coupled circuits. (4M)

c) State and explain Faraday’s laws of electromagnetic induction. (4M)

5. a) For a half-wave rectified alternating current, find average value, rms value and (7M)
form factor. Find average and rms values when Im=3A.
b) A resistor and capacitor are connected in series across a 150 V AC supply. When (7M)
the frequency is 40 Hz, the current in the circuit is 5 A and when the frequency is
50 Hz, the current in the circuit is 6 A. Find R and C of the circuit.

6. a) An inductive coil of resistance 10 Ω and inductance 0.1 H is connected in parallel (7M)

with a 150 µF capacitor to a variable frequency, 200 V supply. Find the resonant
frequency at which the total current taken from the supply is in phase with the
supply voltage. Also find the value of this current.

ωr L fr
Show that for an RLC series resonant circuit, Qr = =
b) R Band width (7M)

7. Find the current flowing through branch A-B of the network shown in figure 7, by (14M)
applying Norton’s and Thevenin’s theorem. Verify the equivalence between
Norton’s equivalent circuit and Thevenin’s equivalent circuit. All the values of
resistances and reactances in the circuit are in ohms
A B
10 j4 2 j3
9∠ 0 0 V -j4 4

Figure 7

2 of 2

WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
Code No: R161208 R16 SET - 1

I B. Tech II Semest
ster Supplementary Examinations, Novemberr - 2021
ELECT
TRICAL CIRCUIT ANALYSIS – I
(El
Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
tion Paper consists of two parts (Part-A and Part--B)
Note: 1. Questio
ering the question in Part-A is Compulsory
2. Answer
er any FOUR Questions from Part-B
3. Answer
~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ~~~

PART –A
1. a) Two capacitors, C1= 2:0
:0 µF and C2= 10 µF, are connected in series. Find
ind the (2M)
equivalent capacitance.
b) List the properties of a tree
tr in a graph (2M)
c) Distinguish between Ele
lectrical and magnetic circuits (2M)
d) Distinguish between Per
eriodic and A periodic waveforms (2M)
e) Explain the concept off S
Series resonance (2M)
f) What is the significance
ce of Locus Diagrams (2M)
g) When a voltage v = 1200 sin 5000 t volts is applied to a series circuit ofL
fL = 0.06 H (2M)
nce, the resulting current is i = 2 sin(5000 t +900) amperes.
and unknown capacitanc
Calculate the unknown
n capacitance.
c

PART -B
2. a) Find Rab for the followin
ing circuit: (7M)

b) Find all branch currents

ts for the network shown below:
(7M)

3. a) Explain the steps involv

lved to draw the dual of any network (7M)

1 of 3

|''|'|''|''|''|||'|| www.manaresults.co.in
Code No: R161208 R16 SET - 1

b) For the network shown below, obtain the incidence matrix and also find the (7M)
current through 20

4. a) Define the following terms w.r.t magnetic circuits: (7M)

i) Flux density ii) magneto motive force iii) magnetic field strength iv) Reluctance
b) Compute the voltage V for the following coupled circuit: (7M)

5. a) For the following circuit find i)the total impedance ii)the total current and (7M)
iii)Power factor

b) Determine the rms value of the current waveform shown below. If this current is (7M)
passed through a resistor of 9 resistor, Calculate the average power absorbed by
the resistor.

2 of 3
|''|'|''|''|''|||'|| www.manaresults.co.in
Code No: R161208 R16 SET - 1

6. a) Define the term Quality factor and explain its effect on bandwidth. (7M)

b) For the circuit shown below, Plot the locus of the current, mark the range of (7M)
current for maximum and minimum values of R, and the maximum power
consumed in the circuit.

7. a) (7M)
State and explain millman’s Theorem
b) Find the the venin equivalent for the circuit shown below: (7M)

3 of 3

|''|'|''|''|''|||'|| www.manaresults.co.in
 Code No: R161208 R16 SET - 1
I B. Tech II Semester Supplementary Examinations, December - 2020
ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question paper consists of two parts (Part-A and Part-B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PART –A

1. a) State the V-I relation of the capacitance and inductance. (2M)

b) How do you form tree and co-tree in the network topology? (2M)
c) What is the difference between self-inductance and mutual inductance? (2M)
d) Find the complex power when (2M)

e) Draw the locus diagram of RC series circuit assume that C is fixed R is variable. (2M)
f) State the compensation theorem. (2M)
g) State reciprocity theorem. (2M)
PART –B

2. a) Describe different types of active elements and passive elements in the circuit (7M)
analysis.

b) By using the mesh analysis determine the loop currents in the following circuit. (7M)

1 of 3

|''|'|''|''|''|||'|| www.manaresults.co.in
 Code No: R161208 R16 SET - 1

3. a) For the network shown in the following figure, write tie-set schedule and hence (7M)
solve for all branch voltages and branch currents.

b) For the network shown in the following figure, write cut-set schedule and hence (7M)
solve for all branch voltages and branch currents

4. a) Describe in detail the analogy between electrical and magnetic circuits. (7M)
b) How do you use dot convention? For mutually coupled parallel coils show that (7M)
L1 L 2 − M 2
L eq =
L1 + L 2 − 2M
5. a) For the periodic wave form shown in the following figure, determine average and (7M)
rms values.

b) Calculate the reactive power in the inductor and capacitor in the circuit of the (7M)
following figure.

2 of 3
|''|'|''|''|''|||'|| www.manaresults.co.in
 Code No: R161208 R16 SET - 1

6. a) By using the nodal analysis determine various node voltages in the following (7M)
circuit.

b) A series R–L–C circuit has a supply input of 5 volts. Given that inductance, L = 5 (7M)
mH, resistance, R = 75 and capacitance, C = 0.2 F, determine (i) the resonant
frequency, (ii) the value of voltage across the capacitor at the resonant frequency,
(iii) the frequency at which the p.d. across the capacitance is a maximum, and (iv)
the value of the maximum voltage across the capacitor

7. a) Assuming that (4 – j3) branch as load in the following circuit, determine (7M)
maximum power transfer to this branch.

b) Use superposition theorem, determine V0 in the following circuit. (7M)

3 of 3

|''|'|''|''|''|||'|| www.manaresults.co.in
Code No: R161208 R16 SET - 1

I B. Tech II Semester Supplementary Examinations, January/February - 2023

ELECTRICAL CIRCUIT ANALYSIS – I
(Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 70
Note: 1. Question Paper consists of two parts (Part-A and Part-B)
2. Answering the question in Part-A is Compulsory
3. Answer any FOUR Questions from Part-B
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PART –A (14 Marks)
1. a) Find the total resistance between points 1 and 2 for the following network: [3M]

b) Distinguish between a planar and non- planar graph. [2M]

c) Define the term coefficient of coupling w.r.t magnetic circuits. [2M]
d) If v = 200 sin 377t V and i = 8 sin (377t - 30°) A for an ac circuit, determine [3M]
(i) The power factor, (ii) apparent power, and (iii) reactive power.
e) Explain in detail about the power triangle. [2M]
f) State and explain reciprocity theorem. [2M]
PART –B (56 Marks)
2. a) State and explain the ohms law and also explain about the Resistance, Inductance [7M]
and capacitance parameters.

b) For the following circuit, determine R so that the power going in to the terminal’s [7M]
ab is maximum. Also calculate the maximum power

3. a) Explain the steps involved in finding the fundamental cut sets and also list its [7M]
properties.
b) For the network given below, write the fundamental cut set matrix and hence find [7M]
the KCL equations:

|''|'|''|''|''|||'|| www.manaresults.co.in
 Code No: R161208 R16 SET - 1

4. a) Two coils of self-inductances L1 and L2 are mutually coupled. Derive the [7M]
expression for the net inductance of the coils if they are connected in Series
Aiding.
b) For the following coupled circuit, find the voltage across 5 resistor. [7M]

5. a) Analyze the Series RLC circuit with corresponding impedance diagram along [7M]
with supporting Phasor diagram.
b) For the circuit shown below, find the power delivered by the source. [7M]

6. a) Explain the following terms related to resonance circuits: [7M]

i) Band Width and ii) Quality factor
b) Calculate the average and effective values of the following waveform and also [7M]
find the form factor

7. Find the current in the 5 for the following circuit using Thevenin’s theorem [14M]

*****

2 of 2

|''|'|''|''|''|||'|| www.manaresults.co.in