BILL OF QUANTITY FOR STP

DOUBLE TREE BY HILTON AT AMRITSAR PUNJAB

UTTAM ENVIRO TECH ENGINEERS PVT. LTD. AMRITSAR

ESTIMATE FOR SEWERAGE TREATMENT PLANT

S.N Description Unit Qty Rate

A SEWAGE TREATMENT PLANT

Design, supplying, installing, testing & commissioning of Sewage Treatment

Plant of 110 KLD with Ultra Filtration

Inlet Sewage Characterstics

Flow rate - 110 KLD

pH - 5.5 to 8.5
BOD - 250-300 mg/l
S. Solids - 250-350 mg/l
COD - 400-600 mg/l
Oil & Grease - Upto 50 Mg/L

Effluent discharge standard after treatment (After UF)

pH - 6.5 – 8.5
BOD - Less than 10 Mg/L
S. Solids - Less than 10 Mg/L
COD - Less than 50 Mg/L
Oil & Grease - < 2 Mg / L
Nitrogen : <2 mg/l
Phosphorous: <1 mg/l
Fecal Coliform(MPN/1000ml) < 100
Hardness: <50 mg/l

Sewage treatment plant shall include following tanks in RCC (Civil)

Screen Chamber No. 1
Oil & Grease Chamber No. 1
Equalization Tank No. 1
Anoxic Tank No. 1
MBBR Tank No. 2
Tube Settler Tank No. 1
Filter Feed Tank No. 1
UF Feed Tank No. 1
Flushing/Irrigation Water Storage Tank No. 1
Soft Water Storage Tank No. 1
Sludge Holding Tank No. 1

Note: 'Contractor shall ensure submission of detailed GA drawings (Plan & Section), P &
I diagram, schematic diagram for the mentioned component in SOQ and additional
component if so required for the complete working of the STP and got it approved by
the Owner’s Architect / Project Manager / Consultants.

A MECHANICAL EQUIPMENT

1 Supply, installation, testing & commissioning of Stainless Steel Coarse Screen with suitable lifting No. 2 12500
arrangement (size shall be as per actual drawings). Spacing between bars to be 16 mm for
coarse screens and 10 mm for fine screens.

Make : Uttam
Supply of MS hot dip galvanized puddle flanges in accordance to BS:10 table D as required to 11500
be provided (in the structural slab and wall) of various diameters. Puddle flanges shall be
provided for all the structural component of the STP. The installation of the puddle flanges
2 shall be carried out by the Civil contractor in accordance to the Civil GA drawing (to be Lot 1
prepared by the STP contractor) at the required levels & position; under the supervision
of the STP contractor.

Make : Uttam
3 Supply, installation, testing & commissioning of float type level switches for automatic Lot 1 55000
operation of the system with high/low level alarm complete with auxillary NO/NC contacts
for (To be provided for all the tanks and plant room
sump)

Make: L&T, Siememns or Equivalent

4 Providing and fixing of Submersible Agitator Mixer for Anoxic Tank - Min.1.1 KW (3 Phase) with CI No. 1 28000
Casing & SS Propeller with suitable Lifting Arrangement to be provided along with the mixer.

Make: Uttam S D Aqua

Supply, installation, testing & commissioning of non clogging type pumps capable CI
casing & CI impeller complete with all accessories, motor of required capacity, suction and
5 delivery headers and valves. Pumps shall have following duty: The provsion of local push button
near the pumps should be considered.

Cost shall be inclusive of PVC flexible Hose pipe ( for piping submreged in effluent) with
PVC piping (for piping non-submerged in effluent)
5.1 Submersible Sewage Pumps (non cutter type) for transfer of Raw Sewage in Set 1 85000
EQT (1 working & 1 standby) :-
Flow rate (each) = 5.5 m3/hr
Head = 10-12 m
Make: Kirloskar, KSB, Willo
5.2 Submersible Sewage Pumps (cutter type) for transfer of STP plant room sump Set 1 162000
tanks ( 1 working + 1 standby )

Flow rate (each) = 15 m3/hr,

Head = 15 m

Make: Kirloskar, KSB, Willo

6.0 Air diffusion system shall include the following:

6.1 Air Blower for Equilisation, MBBR Tanks and sludge tank : Air blowers of suitable HP Suitable Set 1 295000
for 415 ± 10% volts, 3 phase, 50 cycles A/C supply. Numbers & capacity as per
requirement with standby to be specified by
vendor.Capacity: 150 m3/hr , @ 0.4 kg/cm2 Qty (1W+1S) Make: Akash, Uttam

Non clog, Self Cleaning type air dispersion system capable of handling 3-5 cfm of air with 55000
oxygen transfer efficiency of 3-4% per / meter water depth. Air dispersion grid shall be
assembled in modular form so that they can be replaced
6.2 / repaired easily from plat form at the top. (Coarse Disc Type Diffusers for EQT & Lot 1
SHT)

Non clog, Self Cleaning type air dispersion system capable of handling 3-5 cfm of air with 135000
oxygen transfer efficiency of 3-4% per / meter water depth. Air dispersion grid shall be
6.3 assembled in modular form so that they can be replaced Lot 1
/ repaired easily from plat form at the top. (Fine Bubble Tube Type Diffusers for
Aeration Tank)

make: Rehau (Germany)

7 Supply, installation, testing & commissioning of MBBR media consisting of Virgin PE / PP carrier Lot 1 145000
modules with Surface not less than 400 M2/M3. The media qty. shall be calculated based on 6-12
gm/m2 area.

Make: Uttam, Universal tech

8 Supply, installation, testing & commissioning of Tube deck media of reputed make with Lot 1 62000
suitable quantity. The surface area of Tube Deck shall be 11 m2/m3 and the quantity will be
based on max 2.0 m/h velocity.

Make: PP Aqua
9 Providing and fixing all piping (as described below) and isolation control valves for making the
system complete.

Non Submerged Air Piping - MS C Class 250000

Submerged Air & Water Piping - PVC Flexible Braided
Pumps suction & delivery headers, frontal piping of FRP vessels & other interconnecting - Lot 1
GI B class
Tanks overflow & drain - PVC 6 kg / cm2

Make: Tata, Jindal. Astral, Finolex

 Providing, fixing, testing and commissioning of multistage horizontal / vertical centrifugal
pumps or monoblock pumps 2 pole, 50 HZ, AC (as per IS : 9079) incorporating SS
Casing C.I. casing and frame, stainless steel shaft, bronze / SS impeller,Suction & Discharge
Shall be CI with TEFC induction motor directly coupled to the pump, IP44 protection, class B
insulated, C.I. body, hydraulically and dynamically balanced to give vibration free operation, with
mechanical seal arrangement, fixed on a base plate with suitable vibration eliminator pads
10 complete with level switch, Pressure switch , necessary wiring / Cabling (from tank to
pumps & panel), pressure gauge, valves, vibration eliminators on the delivery side and
strainer on suction side, including non-return valve and isolating valves on suction and delivering
sides as required, including suction and delivery headers and interconnecting piping (GI Heavy)
complete in all respects.

10.1 Flow Rate (each) : 9 m3/h

Head : 30 M
RPM : 2900
(1 Working + 1 Standby)
(Filter Feed Pumps) Set 1 92000
Make: Kirloskar, KSB, Willo
10.2 Flow Rate (each) : 6.0 m3/h
Head : 30 M
RPM : 2900
(1 Working + 1 Standby)
(Softener Feed Pumps) Set 1 92000
Make: Kirloskar, KSB, Willo
11 Supplying, installation, testing and commissioning of Horizontal centrifugal sludge Set 1 78000
recirculation pumps for tank coupled with motor of capacity 10 m3/h at 10 m head of C.I. Parts
and mechanical seal complete with isolation and non-
return valves. (1 working + 1 standby)

Supply, installation, testing and commissioning of Filters constructed of M.S material Epoxy
Coating / Composite FRP. The inner distribution system and the under bed draw off system shall
be of Hub & Lateral type / Riser tube with top & bottom strainers of vessel shall be supplied
with first fill media with supporting media like silex, gravel etc. The Filter shall be complete with
12 pressure gauge at inlet & outlet, sample cock, MS / UPVC interconnected piping, manual
valve, overflow & drain, outlet fitting and all associated pipe work with manual Butterfly Valves/
MPV.

12.1 Multi Grade Filter 900Diax 1500 Height

Capacity : 9 m3/h (each)
Filteration Rate : 17500 L/Sqm/Hr
Operating pressure : 3.0 kg/Sq.cm
Test pressure : 4.5 kg/Sq.cm No. 1 162000
Make: Uttam Enviro
12.2 Activated Carbon Filter 900 Diax 1800 Height
Capacity : 9m3/h (each)
Filteration Rate : 15000 L/Sqm/Hr
Operating pressure : 3.0 kg/Sq.cm
Test pressure : 4.5 kg/Sq.cm No. 1 210000
Make: Uttam Enviro
Supply, installation, testing and commissioning of Softener constructed of M.S material
Epoxy Coating / Composite FRP. The inner distribution system and the under bed draw off
system shall be of Hub & Lateral type / Riser tube with top & bottom strainers of vessel shall
be supplied with first fill media with supporting media like silex, gravel etc. The Softener shall
be complete with pressure gauge at inlet & outlet, sample cock, MS / UPVC interconnected
13 piping, manual valve, overflow & drain, outlet fitting and all associated pipe work with manual
Butterfly Valves/ MPV. Cost shall be inclusive of HDPE Brine tank with motorized agitator and 1
Hardness test kit for first time.

Water Softener, Dia. 1200x 2500 height

Inletr Hardness : 500 mg/l
Treated Hardness : Less than 50 mg/l
Capacity : 6.0 m3/h (each)
Operating pressure : 3.0 kg/Sq.cm
Test pressure : 5.5 kg/Sq.cm
Brine Tank : 1000 Ltrs
 Qty : 1 Set as above No. 1 550000
Make: Uttam Enviro Hydro care Engineers
Providing, installing, testing and commissioning of Ultra Filtration (UF) system having filtration 1475000
flux @ 40 - 50 L/m2/hr at 25 deg for further polishing treated water of 9m3/hr capacity.
The system shall be complete with UF Feed pumps(1W+1SB) Backwash Pumps
(1W+1SB), Cartridge Filters, UF Membranes Flushing / Cleaning System,
complete instrumentation for automation and monitoring, Rotameters, Pressure
14 Gauges, interconnecting pipework, electrical cabling and switchgear, electrical panel, all Set 1
complete as described in Scope of Work enclosed herewith.
Note: The process and the control system of Ultra Filtration (UF) Package shall be in complete
conformity of the UF Sytem Manufacturer

Make: Uttam Enviro Hydro care Engineers

15 Supply, installation, testing and commissioning of Ozone generator of 30 grams / hour complete No. 1 125000
with piping and other components complete.

Make" Sukriti, Alpha

Supplying, installing, testing and commissioning of dosing system (Sodium Hypochlorite 25000
dosing for disinfection in Filter Feed Tank & Dosing System) consisting of one HDPE tank of
100 litres capacity with a positive displacement diaphragm 1 No Working dosing pump having
variable flowrate of 0-6 lph. The motor shall be suitable for operation at 240 V / single phase/50
16 Hz. Supply. The pump shall be supplied complete with necessary polypropylene piping, No. 1
valves, strainers, low level switch and injection fittings. The pump shall be speed & stroke
control.

Make: E-dose
Supplying, installing, testing & commissioning of ultravoilet dis-infection unit. The unit shall
have over 99.9 % bacterial reduction from inlet to outlet. The dis- infection chamber shall be
constructed of SS 316L on all welted parts. The UV lamp shall be of low pressure mercury vapour
17 type with hard glass enclosure, the sockets shall be water tight & vibration resistant. The lamp life
shall be rated for 6000 hours. The unit shall be complete with temperature safety control and lamp
out alert circuit.

The UV unit shall have with reactor, cabinet housing, cabinet cooling, treatment chamber,
electrical panel, temperature safety control, lampout alert. The UV Dosage should be >
60,000 uW – Sec / sq.cm. The lamps should be selected
based upon the flow requirement of respective unit

17.1 Outlet of Flushing Water Transfer - 6.0 m3/hr No. 1 155000

17.2 Outlet of Irrigation Water Transfer - 6.0 m3/hr No. 1
17.3 Outlet of Soft Water Transfer - 6.0 m3/hr No. 1
Make: Alpha, Sukriti
18 Supply, installation, testing and commissioning of Top Manual Discharge Basket Type Centrifuge Set 1 285000
of 300 mm dia with 1 Working & 1 Stand by Centrifuge Feed Pumps and Poly Dosing
System.

Make: Universal tech Trade, SD Aqua

19 Instrumentation:
Supply of Microprocessor Based Electo Magnetic Flow Meter for Total Plant Capacity of below
flow rates each with pulsed DC excitation having automatic 'Zero' correction measurement,
compact instrument version with measuring sensor (Primary) and Amplifier integrated in
one mechanical unit (Suitable for required flow range, inlet/outlet connections, measuring
19.1 pipe material SS 304 / CI, Electrode material - SS with 16 character x 2 Lines LCD
Alphanumeric Display for flow rate, totalizer, diagnostic message, with all accessories for inlet
flow measurement

19.1.1 Oulet of Raw Sewage Transfer Pumps - 5.5 m3/hr Make Zest, Astral No. 1 66000
19.2 Supply, installation, testing and commissioning of BMS compatible Digital Turbine Type
flow meter with online sensor, standard cable and fitting for flow measurement.

19.2.1 Outlet of Flushing Water Transfer - 6.0 m3/hr No. 1 22000

19.2.2 Outlet of Irrigation Water Transfer - 6.0 m3/hr No. 1
19.2.3 Outlet of Soft Water Transfer - 6.0 m3/hr No. 1 22000
19.2.4 Outlet of ACF - 9 m3/hr No. 1 25000
19.2.5 Outlet of UF - 9 m3/hr No. 1 25000
19.3 Online PH Controller in STP outlet No. 1 25000
19.4 Online DO Controller in Aeration Tank No. 1 25000
19.5 Online Monitoring System for monitoring of STP Treated Parameters such as BOD, COD, No. 1 725000
TSS Make Novem Controls
20 Treated Water Hydropneumatic System for Supply & Distribution
Supply, Installation, Testing And Commissioning Of Compact Self Contained Skid Mounted
Hydropneumatic System As Follows:

a. Vertical, In-Line, Multisage, centrifugal pumps with SS-304 casing and impeller and SS shaft,
CI base & head TEFC motor (with mechanical seal)

(Vendor to submit performance curves and technical catalog of the proposed model for
review & information) Pumps shall be factory assembled and factory tested with 1 VFD
common.

The pump shall be selected for performance at best efficiency point. However, the pump
selection shall be suitable for performance with set point @ + 20% of the rated head.

b. External Pump mounted or wall mounted microprocessor PID controller and frequency
inverter integrated in a single body or as separate components with pressure sensor
transmitter minimum two lined LCD display, diodes to indicate pump ready, pump running
and fault and capable to communicate with other controllers following MODBUS-RTU or
BACNET Class-2 protocall through RS485 port. System should be capable to
compensate for frictional losses at lower flows. All alarms should be displayed in the
controller. System should be equiped with dry running protection

Quantity : 1 Set vith common VFD

c. Complete (Skid mounted wall mounted / floor mounted) electrical control panel comprising of
all accessories such as PLCs, pressure switches, pressure transducers, control wiring
and any other necessary imports etc. (list to be provided by the vendor)

d. Precharged diaphram pressure vessel with food grade membrane, charging connection,
connected to outlet header with necessary flanges, gaskets, isolating valves, nuts/bolts etc
complete.

e. Set of accessories such as pressure switches, pressure transducers, inter connecting

power and control cabling etc. complete

f. Accessories like pressure gauge, MS base frame (Synthetic enamel painted over a coat
of primer)
g. GI suction and delivery header with flanges for inlet connection, common outlet header
with flanges for outlet connections as required, and inter connecting piping with
flexible connections, eccentric type reducers etc. all necessary indigenous accessories as
required to complete the installation.

20.1 Flushing Water Hydropneumatic System

Water Flow Rate : 6.0 m3/hr (each)
Head : 80 m
Purpose : Flushing Water Transfer
1 Set : No. of pumps 2 (1 Working + 1 Standby) Set 1 525000
Make Willo Kirloskar
20.2 Irrigation Water Hydropneumatic System
No. of pumps 2 (1 Working + 1 Standby)
Water Flow Rate : 6.0 m3/hr (each)
Head : 45 m
Purpose : Irrigation Water Transfer
1 Set : No. of pumps 2 (1 Working + 1 Standby) Set 1

20.3 Soft Water Hydropneumatic System

No. of pumps 2 (1 Working + 1 Standby)
Water Flow Rate : 6.0 m3/hr (each)
Head : 80 m
Purpose : Soft Water Transfer
1 Set : No. of pumps 2 (1 Working + 1 Standby) Set 1 525000
Make: Willo Kirloskar
Approval from pollution board including consent to operate at initial & various other stages 150000
of works including preparation of report / drawings as per pollution board requirement,
arrangement of raw sewage. Contractor shall include the cost of all chemicals consumed and
21 the cost of such items of works which are not explicitly mentioned above, but are mandatory Job
to have pollution board approval. Liasioning shall be in the scope of vendor & Recipted
Fee in Client Scope.
 Design, fabrication, assembling, wiring, supply, installation, testing and
commissioning of motor control centre fabricated out of 14 gauge CRCA sheet steel. Cable
gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be
treated with all anticorrosive process before painting as per specifications with 2 coats of red
oxide primer and final approved shade of powder coated paint. 2 Nos. earthing terminals shall be
22 provided for 3 phase, 4 wire, 50 Hz supply system. Lifting hooks shall also be provided in case of
large panels. Approval shall be taken for each panel before fabrication. Quoted rates shall be
inclusive of cables (in accordance to specification) with earthing from panel to each motor /
equipment.

Motor Control Centre (Common for STP)

Incoming
150 amps TPN MCCB with the following accessories:
a. 0-500 volts 96 x 96 mm square electronic voltmeter with selector switch shall be protected by 2
amps TP MCB. 1 Set

b. 0-100 amps 96 x 96 mm square electronic ammeter with selector switch and 100./5 amps 10
VA CL:1 CTs. 1 Set

c. Phase indicating lamps shall be protected by 2 amp SP MCB 3 Sets

Bus Bar
Outgoing
200 amps TPN (15 KA) copper bus bar with heat shrinkable insulation sleeves.
a. Required Nos of required capacity TPN MCB for direct on line starter/star delta starters and
out going feeders to all the pumps/blowers etc. (including standbies). Each
compartment shall contain auto / manual selector switch and indicating lamp with MCB’s for
‘ON/OFF/TRIP’ status of motor

b.Necessary cable alleys, internal / cabling, wiring, cabling from MCC to various pumps /
equipment and interlocking, earthing for all equipment shall also included.

c.All MCCBs/MCBs shall be of 15 KA breaking capacity and suitable for motor duty
application.
d.All motor starters shall be provided with Automatic level controller
e.DOL starters shall be used for mototrs below 7.5 HP and Star-Delta Starters for other motors
above 7.5 HP .

f.Provision shall be made for providing potential free contacts to all pumps starters
g. Energy Meter to be provided with Panel
MCC for all STP equipments/pumps as described above Set 425000

23 Providing and fixing electrical cables, cable trays, control cabling, earthing etc with in the STP Lot 155000
from electrical panel to the equipments complete in all respect as per direction of Engineer in
charge .

TOTAL AMOUNT Rs. 7272500.00

 5/6/2024

Amount

25000

11500
55000

28000

85000

162000

295000

55000

135000

145000

62000

250000
92000

92000

78000

162000

210000
 550000

1475000

125000

25000

155000
Not required
Not required

285000

66000

22000
Not required
22000
25000
25000
25000
25000
725000
 525000

Not Required

525000

150000
 425000

155000

7272500