GENERAL TROUBLESHOOTING PROCEDURE

Changing External Parts (1) Face Cover ............................................................. 1

Changing External Parts (2) Belt Cover ............................................................... 2
Changing External Parts (3) Base Cover ............................................................. 3
Changing External Parts (4) Bed Cover/Base Lid (2) .......................................... 4
Changing External Parts (5) Base ....................................................................... 5
Changing External Parts (6) Front Cover ............................................................. 6
Changing External Parts (7) Rear Cover ............................................................. 7
Adjusting Needle Drop Position ........................................................................... 8
Adjusting Hook Timing ......................................................................................... 9
Adjusting Needle Bar Height ............................................................................... 10
Adjusting Clearance between Needle and Hook ................................................ 11
Adjusting Backlash between Hook Drive Gear and Lower Shaft Gear ............... 12
Adjusting Height of the Needle Stop Position ..................................................... 13
Adjusting Thread Tension .................................................................................... 14
Adjusting Tension Release Mechanism .............................................................. 15
Changing Thread Tension Unit ............................................................................ 16
Replacing Threader Plate and Adjustment ......................................................... 17
Adjusting Height of Embroidery Foot P ............................................................... 18

ADJUSTMENT FOR ELECTRICAL COMPONENTS

Connector Connection Diagram .......................................................................... 19
Replacing Printed Circuit Board “A” (Main board) ............................................... 20
Replacing Touch Panel ....................................................................................... 21
Replacing Printed Circuit Board “F” & “F2” ......................................................... 22
Adjustment of the Solenoid ................................................................................. 23
Replacing DC Motor and Motor Belt Tension Adjustment ................................... 24
Replaching Carriage Plate (Unit) ........................................................................ 25
Adjusting X and Y Sensors ................................................................................. 26
Adjusting X and Y Sensors (Simple Adjustment) ................................................ 27
Adjusting X Mortor Gear ..................................................................................... 28
Replacing Switching Power Supply ..................................................................... 29
MC350E

Changing External Parts (1) Face Cover

C Replacing th face cover

To remove:
1. Remove the Cap A and Screw B and remove
the Face Cover C .
A Cap
B Screw
C Face cover

To attach:
2. Follow the above procedure in reverse.

A
B

1
MC350E

Changing External Parts (2) Belt cover

Replacing the belt cover

To remove:
1. Remove the Cap A and Screw B .
2. Raise the Carrying Handle and remove the Screw C .
3. Lay the machine on its back and remove Screws D
(2 pcs. gold color), then remove the Belt cover E .

A Cap
B Screw
C Screw
E D Screw
E Belt cover

To attach:
B
4. Attach the Belt Cover with Screws B - D .
5. Attach the Cap A .

2
MC350E

Changing External Parts (3) Base Cover

Replacing the base cover

To remove:
1. Remove Screws A (4 pieces) to remove the base
cover B .

A Screws
B Base cover

To attach:
2. Follow the above procedure in reverse.

A A

A A

3
MC350E

Changing External Parts (4) Bed Cover / Base Lid (2)

Replacing the bed cover

To remove:
1. Remove the base cover. (See page 3)
2. Remove Screw A (2 pcs.), and remove the Base
Lid B .
3. Remove Screw C (2 pcs.), and remove the Bed
cover D .

A Screw
B Base lid
C Screw
C D Bed cover
D A
B To attach:
4. Follow the above procedure in reverse.

Replacing base Lid (2)

To remove:
1. Remove Screws A (4 pieces), and remove the
Lid (2) B .
A
A Screw
B Base lid (2)

To attach:
2. Follow the above procedure in reverse.

A
B

4
MC350E

Changing External Parts (5) Base

Base
A
To remove:
1. Remove the Belt cover. (See page 2)

2. Remove Setscrew A (4 pcs.), and remove

the base unit .

3. Remove the X-Motor Connector D and Y-Motor

Connector C from the printed circuit board “A”.
A Setscrew
B Joint bosses
C Y-motor connector (White)
A
D X-motor connector (Blue)
E Extension table (Accessory)
D C

To attach:
4. Attach the X, Y-Motor Connectors C , D into
the printed circuit board “A”.

5. Insert the X, Y-Motor Cords between the printed

cuircuit board “A” and Arm. Be sure the cords
are not caught between the Joint Bosses B of
B the arm and base. Tighten Screws A (4 pieces)
temporarily.

E
6. Attach the Extension (Accessory) table E .

7. Tighten Screws A while aligning the extension

table, base unit and free Arm.

Note: Attach the embroidery hoop with the template

on the carriage. Check the needle drop postion
against the template.

8. Attach the belt cover.

5
 MC350E

Changing External Parts (6) Front Cover

Front cover
To remove:
1. Remove the face cover, belt cover, base cover.
B (See pages 1-4).
2. Remove Screw A and remove the Arm thread
guide (lower) B .
A F
3. Remove Screw C .
4. Loosen Screws D , E 3 turns.
5. Disconnect the each connector and remove the front
cover.

Note: Disengage the Hooks F to remove the Front

cover.

A Screw
B Arm thread guide (Lower)
C Screw
C D Screw
E Screw
F Hooks
D

To attach:
6. Follow the above procedure in reverse.

Note: See pages 19 (Diagram) for Connectors

Connection.

6
MC350E

Changing External Parts (7) Rear Cover

Rear cover

To remove:

1. Remove the face cover and belt cover. (See page 1,2)

2. Loosen Screw A , B , C , D , and remove the

rear cover.

A Screw
B Screw
C Screw
A D Screw

To attach:
3. Follow the above procedure in reverse.

B
Carriage

C
Rear cover
Cap

7
 MC350E

Adjusting Needle Drop Position

The needle should be positioned at the center of the needle plate hole.

1. Lower the needle to its lowest position by turning the

A handwheel.

2. Remove the face cover and loosen Screw A ,

move the Needle bar supporter B to the right or
left until the needle C comes to the center of the
Needle plate hole D .

B 3. Tighten the Screw A .

4. Attach the face cover.

A Screw
B Needle bar supporter
C C Needle
D Nedle plate hole
D

8
 MC350E

Adjusting Hook Timing

The hook timing is that amount of ascending travel of the needle bar from its lowest
position to where the tip of the rotary hook meets the left side of the needle should be 3.1
to 3.7 mm.

1. Remove the belt cover, bed cover, base cover, base

lid (1) and base lid (2).
A

2. Remove the presser foot, Needle plate A and

B
Bobbin holder B .

3. Lower the needle bar at its lowest position F by

turning the handwheel toward you.

4. Raise the needle bar 3.4 mm up from the lowest

C position.

5. Loosen the Screws C of lower shaft gear, turn the

Lower shaft gear D until the tip of rotary hook
meets with the left side of the Needle E .
Tighten screw (2 pieces) C of the lower shaft
gear.

6. Attach the Bobbin holder, Needle plate, presser foot

and Needle.

D C 7. Attach the base lid (2), base lid (1) base cover, bed
cover and belt cover.

A Needle plate
B Bobbin holder
Needle E C Screw
D Lower shaft gear
3.1 - 3.7 mm E Needle
F Lowest position

9
 MC350E

Adjusting Needle Bar Height

The standard distance between the top of the needle eye and the upper surface of the hook
race should be in the range of 1.6 - 2.0 mm when the rotary hook meets the left side of the
needle in ascending travel of needle from its lowest position.

A 1. Remove the presser foot, Needle plate A and

Bobbin holder B .

2. Remove the face cover.

B 3. Turn the handwheel to raise the needle bar from

the lowest position until the tip of the rotary hook C
meets with the left side of the needle D .
Turn the handwheel to raise the needle bar further
1.8 mm.

4. Loosen the Setscrew.

5. Move the Needle bar E up or down to align the

Top of the needle eye F with the Upper surface
of the hook race G .
Setscrew

6. Tighten the Screw. Be sure that the Groove H

on the needle bar is facing right in the front.
E

7. Attach the Bobbin holder B , Needle plate A and

presser foot.

8. Attach the face cover.

A Needle plate
H
B Bobbin holder
C Rotary hook
D Needle
E Needle bar
F Top of the needle eye
G Upper surface of hook race

C
G
D
1.6 - 2.0 mm

F
Hook race body

10
MC350E

Adjusting Clearance between Needle and Hook

The clearance between needle and rotary hook should be - 0.1 to + 0.05 mm.

1. Remove the needle plate, bobbin holder, base cover

and bed cover (See pages 3 - 4).
A B
Replace the needle with the Test pin D .

2. Loosen Screws A , B , C temporarily and retighten

Screw B slightly.

3. Turn the handwheel to bring the tip of the rotary hook

behind the test pin D .

4. Adjust the clearance between the test pin D

and the Tip of rotary hook E to - 0.1 to + 0.05mm F
G C by moving the Rotary hook set plate G up or down.
Tighten the Screws A , B , C firmly.

5. Check the rotary hook driver gear and the lower shaft
gear backlash.
If gears mesh or engage tightly or loosely, check
“Adjusting Backlash between Hook Drive Gear and
Lower Shaft Gear”. (See page 12)
D
Note: Do not move the rotary hook set plate in a lateral
direction, otherwise the hook timing will change.
E
F 6. Reattach the needle.
Reattach the bed cover, base cover, base lid, bobbin
D
holder, needle plate and needle.

A Screw
B Screw
C Screw
D Test pin
E Tip of rotary hook
F –0.1 to +0.05 mm
G Rotary hook set plate

11
 MC350E

Adjusting Backlash between Hook Drive Gear and Lower Shaft Gear
The rotary play of the hook should be 0.8 mm or less.
Adjust the backlash after the adjustment of the clearance between needle and rotary hook.

B
To check:
1. Turn the power switch “OFF”.
2. Remove the base cover, bed cover, needle plate
and bobbin holder.
3. Jog the hook race with fingers to check the rotary
B
play.
“If the play is larger than 0.8 mm or the gears do not
turn smoothly, adjust the backlash as follows”.
A

Adjustment procedure:
1. Remove the bed cover (See page 4) and loosen the
A Screw A .
2. Turn the Lower shaft bushing B (Eccentric), in the
direction “B” when the play at shuttle hook tip is too
small.
3. Turn the Lower shaft bushing B (Eccentric), in the
The rotary hook play direction “A” when the play at shuttle hook is too large.
should be 0.8 mm or 4. Tighten Screw A securely after adjustment.
less.
Note: Do not move the lower shaft bushing in a lateral
direction, otherwise the torque of thelower shaft will
change.

A Screw
B Lower shaft bushing

12
 MC350E

Adjusting Height of the Needle Stop Position

The standard height of needle stop position should be 14.2 mm above the needle plate
surface when the machine is topped.

1. Remove the front cover unit. (See page 6)

2. Turn the power switch “ON” and press Start / Stop

button twice.
Stop the machine with the needle in the up position.

Needle #11 3. (A) If the needle stops higher than 14.2 mm C ,

loosen Screw A and turn the Upper shaft
shield plate B in the direction of (A).
C (B) If the needle stops lower than 14.2 mm C ,
loosen Screw A and turn the Upper shaft
shield plate B in the direction of (B).

4. Place the right side of the Upper shaft shield plate

in the center of the slit of the Upper shaft sensor D
B A and tighten Setcrew A .

5. Press the Start/Stop button twice to check the height

（B）
of the needle stop position.

6. Attach the front cover.

（A） A Screw
B Upper shaft shield plate
C Needle height (14.2 mm)
D Upper shaft sensor
D

13
 MC350E

Adjusting Thread Tension

The standard upper thread tension should be 51 to 59 grams when the tension dial
is set at “3”, measured with a #50 polyester thread being pulled at approximately 110
mm/sec. in the direction of arrow.

1. Set the tension dial at " 3 ".

2. Lower the presser foot.
(B)
3. Remove the front cover unit (See P. 6).
3. If the thread tension is more than 59g, turn the lead screw
in the direction (A).
(A)
4. If the thread tension is less than 51g, turn the lead screw
in the direction (B).

(C) Pulling direction: (Pulling speed 110 mm/ Sec.)

(C)
Polyester sewing thread #50
(White)

14
 MC350E

Adjusting Tension Release Mechanism

When the presser foot lifter is raised, the tension release mechanism should work correctly.
If not, adjust as follows.

A 1 Remove the front cover unit. (see page 6)

2 Lower the presser foot lifter, set the thread tension dial
at “9” and loosen the Screw A .

3 Adjust the play between the tension release rod (2)

B and the Spring holder D approximately 0.3 - 0.5
mm and tighten the Screw A .
4 Raise the presser foot lifter, turn the thread tension
dial from “9” to “0”, make sure the tension disc E
should open 1.0 mm F .

5 Reattach the front cover unit.

A Screw
B Tension release rod (2)
C Play (0.3 - 0.5 mm)
B
D Spring holder
E Tension disc
F Clearance (approximately 1.0 mm)

15
 MC350E

Changing Thread Tension Unit

Replacing the thread tension unit

To remove:
1. Remove the front cover unit. (see page 6)

2. Remove Screws A and B .

3. Remove the thread tension unit.

To attach:
4. Follow the above procedure in reverse.

Note: After the replacement, adjust “Thread Tension

Release Machanism” and Solenoid.

A
A Screw
B Screw

16
 MC350E

Replacing Threader Plate and Adjustment

If the hook on the threader plate is damaged, replace it by following the instructions below.

To replace (Fig. 1):

1. Remove the presser foot.

2. Push down the Threader supporter plate A to

remove from the Pin B . (Fig. 1)

3. To attach the threader supporter plate, match the

groove of the Threader supporter plate A with the
pin B ,and then push it up to insert.

A Threader supporter plate

B Pin
Fig. 1
C Hook
C
D Threader plate
E Screw
B F Screw
A G Setting position plate

If the hook on the threader plate is not aligned with needle eys, adjust it by following the
instructions below.

Adjusting threader plate position (Fig. 2):

Fig. 2 1. When the Hook C is slightly touching the needle
D
eye, loosen Screw E and adjust the Threader plate D
(X) as shown.

If the hook position is too high or too low (Fig. 3):

1. Remove the face cover.
View-X 2. If the hook is too high, loosen the Screw F and
E
lower the Setting position plate G .
If the hook is too low, loosen Screw F to slide up
Fig. 3 the Setting position plate G .

17
 MC350E

Adjusting Height of Embroidery Foot P

Attach the Foot (P), and the space between the needle plate and the bottom surface of the
Foot (P) should be 1.0 to 1.6 mm, when the needle bar is at its lowest position.

1. Remove the rear cover unit.

(See page 7)
E
2. Lower the Needle A and lower the presser foot lifter.

3. Insert the 1.2 mm Feeler gauge B between

the Embroidery Foot (P) C and the Needle plate D .

4. While pressing the Presser bar actuator E down

against the upper shaft cam, loosen the Screw
and push it down in the direction of arrow, then
tighten Screw F again.

5. Reattach the rear cover unit.

A Needle
F B 1.2 mm
C Embroidery front (P)
D Needle plate
E Presser bar actuator
F Screw

D
A

18
 MC350E

Connector Connection Diagram

Please see the following connector connection diagram for the printed circuit board “A”
(Main board).

LCD Harness
Presser foot lifter sensor (Red)
Bobbin winder sensor (Blue)
Upper thread sensor (Red)
Touch panel

Upper shaft
sensor (Black)

Printed circuit board

“F” (Black)

Printed circuit board

“F2” (Black)
DC motor
(White) Remaining bobbin
thread sensor (blue)

Switching power
supply (White)

Inverter
(White)

Upper thread solenoid Lamp

(white)
X- Motor
Y- Motor (Blue)
Remaining bobbi
thread solenoid (White)

Solenoid for thread tension

Thread cutter
sensor switch

19
 MC350E

Replacing Printed Circuit Board “A” (Main board)

To remove:
B 1. Remove the front cover. (See page 6)

A 2. Pull out the connectors of printed circuit board F

A LCD Harness, Inverter and Touch panel.

3. Remove Screws (5 pieces) A and the Printed

circuit board “A” (Main board) B with the Card
guide C .

To attach:
4. Follow the above procedure in reverse.

A Screws
B Printed circuit board A
C Card guide

C
A A

20
MC350E

Replacing Touch Panel

To remove:
K 1. Remove the front cover. (See page 6)
E E
2. Pull out the Connectors of Printed circuit board
I H
“F” (Start/Stop) A , LCD Harness B and Inverter
connector C and Touch panel connectors D .

G 3. Remove Screws E (4 pieces) and remove the

Touch panel F .

E E
To attach:
4. Place the Touch panel F and press it against the
J Ribs G , H , I .
Fix the Touch panel F with the Fixing plate
F
(bottom) J while press it against the Touch panel
F and tighten screws E .

5. Place the Fixing plate (top) K and secure it with

Screws E while pressing the Fixing plate (top) K
against the Touch panel F .

A Printed circuit board F

B B LCD Harness
C Inverter connector
D Touch panel connector
E Screws
A F Touch panel
G Rib
H Rib
I Rib
D
J Fixing plate (bottom)
K Fixing plate (top)

21
 MC350E

Replacing Printed Circuit Board “F” & “F2”

Printed circuit board F2 B To remove:

1. Remove the front cover. (See page 6)
2. Pull out the connector from the printed circuit
board “A” (Mainboard).
3. Remove Screws A (2 pieces) and remove
the Printed circuit board “F” (Start/Stop) B .

To attach:
4. Follow the above procedure in reverse.

To remove:
1. Remove the front cover. (See page 6)
2. Pull out the connector from the printed circuit
board “A” (Mainboard).
3. Remove Screws B (2 pieces) and remove
the Printed circuit board “F2” (Start/Stop) .

A
To attach:
Printed circuit board F
4. Follow the above procedure in reverse.

A Screws
B Screws

22
MC350E

Adjustment of the Solenoid

1. Remove the front cover. (see page 6)

2. Loosen the setscrews A .

3. Adjust the clearance of Solenoid 1.6 mm B with the

tension disk closed.

4. Tighten the setscrew A .

A Setscrews
A
B Clearance of solenoid

The plunger is drawn in direction of Arrow

Tension disk
B

23
MC350E

Replacing DC Motor and Motor Belt Tension Adjustment

Replacing DC Motor

1. Remove the belt cover. (See page 2)

2. Remove the motor belt.

3. Remove the Motor connector A from the printed

circuit board “A” (Main board).

4. Remove Screws B (2 pieces) and replace the

motor.

5. Attach the motorand tighten Screws) B (2 pieces)

slightly.

Adjusting motor belt tension

1. Adjust the Belt deflection to about 5.0 mm C by
A B pressing the middle of the motor belt with your
finger with approximately 200 grams D of pressure.

A Motor connector
B Screws
C Belt deflection (5 mm)
D Motor belt pressure (200 gram)

24
MC350E

Replacing Carriage Plate (Unit)

To remove:
1. Turn the power switch “ON” and select the pattern
B No.1.
A D 2. Turn the power switch “OFF” and remove the Cover
cap A . (Unlock the hook B from the inside.)

3. Turn the power switch “ON” to return the carriage

to the home position.

4. Remove Screws C (3 pieces) and remove the

Carriage plate (unit) D .

To attach:
5. Attach the Carriage plate (unit) D and tighten
screws C temporarily.

6. Adjust the top surface of the carriage plate and the

Arm surface E are parallel and the same level,
securely tighten Screws C .
C
C
7. Attach the cover cap A .

A Cover cap
B Hook
E C Screws
D Carriage plate (unit)
E Arm surface

25
MC350E

Adjusting X and Y Sensors

To adjust X and Y sensors:

1. Turn the power “ON” to return the carriage to

the home position.

(X-1) 2. Turn the power “OFF” and then remove the base
E
69.0 mm unit.
(X-2) 2.5 mm
F 3. Loosen Screw A and adjust dimension “Y” B to
2.5 mm by moving the Y Sensor attaching
plate C .
D
4. Loosen Screw D to adjust Dimension “X-1” E
to 69.0 mm and Dimension “X-2” F to 2.5 mm
G by moving the X Shield plate G .

5. Tighten Screws A and D .

6. Attach the base.

A Screw
B Dimension Y (2.5mm)
C Y sensor attaching plate
A
D Screw
E Dimension X-1 (69.0 mm)
F Dimension X-2 (2.5 mm)
C
G X shield plate

B (Y) 2.5 mm

26
MC350E

Adjusting X and Y Sensors (Simple Adjustment)

To adjust X and Y sensor (without removing the base unit):

1. Remove the base cover.(see page 3)

2. Remove the presser foot and attach the

A
Embroidery hoop “A” A .

3. Turn the power “ON” and select the pattern

No.1

4. Turn the handwheel by hand to check that the

Needle B drops into the Stating position C on
D theTemplate D .
B C
5. Turn the power switch “OFF”.
G
6. If the needle position shifts in Y-direction,
loosen the screw E and move the Y-sensor
fixing plate F to adjust the needle position.

7. If the needle position shifts in X direction, loosen

Screw G through the sheet cover fixing plate H
I hole and adjust the X shield plate position I .
G

8. Turn the power “ON” and select pattern No.1, then

check the start position.

9. Return the carriage to the home position and turn the

power “OFF”.

H
10.Remove the Template and the Embroidery hoop
then reattach the presser foot and base cover.

A Embroidery hoop A
B Needle
C Starting position
D Template
E Screw
F Y-sensor fixing plate
G Screw
H Sheet cover fixing plate
I X shield plate position
E F

27
 MC350E

Adjusting Carriage Motor Gear

If the carriage motor gear sounds noisy when sewing the embroidery stitches, follow the
instructions below.
1. Remove the base unit (See page 5).

2. Remove Screw A and Nylon clip B .

3. Attach the X and Y motor connectors to printed

circuit board “A” (Main board).
C
4. Turn the power “ON” and select large “A” in Gothic
style and memorize it 3 times.

6. Lower the presser foot after the carriage moves to

the starting position.

7. Insert a piece of paper C between the thread

D tension disks as shown so that the needle thread
F I E
sensor will not work.

8. Run the machine and loosen Screws D (2 pieces)

and move the X-Motor E to detect the quitest
position, while the carriage is moving in lateral
direction F then tighten Screws D .

9. Run the machine and loosen Screws G (2 pieces)

and move the Y-Motor H to detect the quitest
position, while the carriage is moving in vertical
direction I then tighten Screws G .

10.Return the carriage to the home position and turn

the power “OFF”. Reattach the base unit.

G H A A Screw
B
B Nylon clip
C Piece of paper
D Screws
E X-motor
F Carriage (moving in lateral direction)
G Screws
H Y-motor
I Carriage (moving in vertical direction)

28
MC350E

Replacing Switching Power Supply

Replacement of Switching Power Supply

To remove:
1. Remove the face cover, belt cover, front cover and
A rear cover.

2. Remove Screws A , B and remove the

machine socket and fixing plate.

3. Pull out the Machine socket unit connector G .

E

4. Remove Screw C and remove the Idler D .

Note: Make sure not to disengage the teeth on the timing

belt and timing gears to prevent the hook timing from
going out of adjustment.

D 5. Remove Screws E (2 pieces) and take out

Switching power supply F .

To attach:
6. Follow the above procedurte in reverse.
C B
7. Move the Idler to adjust the Belt deflection to about
G 4.0 mm by pressing the middle of the Timing belt
with your finger with approximately 100 grams of
pressure.

A Screw
B Screw
C Screw
D Idler
E Screws
F Switching power supply
G Machine socket unit connector
F
Caution: If the fuse on the switching power supply is
blown, critical electronic elements of the power supply
could be damaged. Do not replace the fuse but replace
the power supply to prevent subsequent damage to the
printed circuit board “A” (Main board) or other electronic
comporments.

29
MC 350E

PARTSLIST

37
31
32

33
18
38
27
25 23
18
34 26

9
10

24

36
5
35

2 15
6
16 3
8
7
36
7
28
7
4

19
12 11 22
20
29
13
17

21
14

17
30

2
MC 350E

PARTSLIST
NO. Parts # Description

1 854621004 Needle plate (unit)

2 854104006 Needle plate
3 846030005 Hook cover plate supporter
4 000097613 Setscrew 2x4
5 825016000 Hook cover plate release button
6 825017001 Spring
7 820374004 Setscrew 2x2.3
8 846222109 Rotation stopper
9 820390109 Needle plate setscrew
10 846271103 Hook cover plate
11 860002002 Needle plate positioning pin
12 000111201 Hexagonal socket screw 4x4
13 822314002 Nut
14 860003014 Needle plate nut set plate
15 854105007 Bobbin threader holder lever
16 854138009 Lint brush
17 810220106 Setscrew
18 000081005 Setscrew 4x8
19 860601007 Needle plate set plate (right) (unit)
20 860004004 Needle plate set plate (right)
21 860005005 Needle plate adjusting plate
22 000101105 Setscrew 3x4
23 834014202 Carrying handle supporter (front)
24 852054004 Free arm cover
25 653006101 Cap
26 000161103 Setscrew 3x6
27 000103200 Setscrew 4x30
28 852055005 Bed cover
29 000103509 Setscrew 4x10
30 852003008 Extension table
31 852604005 Face plate (unit)( JAI,JNBV,JA,JUK)
852604500 Face plate (unit)( JCA)
852604407 Face plate (unit)( JLA)
32 852006104 Face plate (JAI,JCA,JNBV,JA,JUK)
852006506 Face plate (JLA)
33 827099003 Reflecting sticker
34 832508006 Thread cutter (unit)
35 852056006 Thread cutter cover
36 810220106 Setscrew
37 852625002 Face plate (unit)( JAI,JCA,JNBV,JA,JUK)
852625404 Face plate (unit)(JLA)
38 100517008 Sticker (JCA)

3
MC 350E

PARTSLIST
1
5
10
9
30

11 28

8 3 24
25
12 32
26
6 27
13 22
14

15 31
7
7
29
16
20 18
2

19 17

21

49 33
4

38 37 35
47 36

51
52
42
36

40 43
42 41

23
43
45
34 37
50
48
39 37
46
44

4
MC 350E

PARTSLIST
NO. Parts # Description

1 852605154 Needle bar supporter (unit)

2 751014006 Needle bar supporter
3 000111902 Hexagonal socket screw 3x4
4 830609518 Needle bar (unit)
5 857602008 Threader positioning setting plate (unit)
6 751047008 Needle bar connecting stud
7 000111201 Hexagonal socket screw 4x4
8 857037006 Threader positioning setting plate
9 751016008 Threader positioning setting block
10 000097602 Setscrew 2x4
11 853509127 Needle threader (unit)
12 755062001 Threader frame
13 853026011 Threader lever
14 755067006 Needle threader spring
15 857603010 Threader shaft (unit)
16 755066005 Threader shaft
17 857038007 Threader guard plate
18 000003508 Knock pin 2x8
19 857039101 Threader plate
20 755095003 Nut
21 755096004 Setscrew
22 000125105 Pin E2x16-CH
23 813404013 Stretch needle (Blue)
24 650607006 Needle bar crank rod (unit)
25 650039001 Needle bar crank rod
26 650040005 Felt
27 650041006 Spring
28 852007002 Needle bar supporter shaft
29 857604011 Threader plate (unit)
30 850662005 Needle bar crank (unit)
31 652512009 Needle bar crank pin (unit)
32 000111108 Hexagonal socket screw 4x6
33 852630000 Thread tension (unit)
34 852516009 Thread tension (unit)
35 854623006 Solenoid (unit)
36 000002105 Snap ring E3
37 000101105 Setscrew 3x4
38 000024505 Spring pin 1.6x18(K)
39 853037004 Cushion
40 830660001 Thread detection lever (unit)
41 834193000 Sensor lever spring
42 000071013 Washer 4
43 000001207 Snap ring E2.5
44 852607008 Sensor base plate (unit)
45 852012000 Sensor set plate F
46 852502002 Printed circuit board G1 (unit)
47 852060003 Solenoid set plate
48 000161103 Setscrew 3x6
49 000081005 Setscrew 4x8
50 000101703 Setscrew 4x12
51 854624007 Link (unit)
52 000103808 Setscrew 3x5

5
MC 350E

PARTSLIST

1
8

7
9 9
8 3
18
4 4
10
2

14 13 14
4 17
15
4

15 16
12

11

6
MC 350E

PARTSLIST

NO. Parts # Description

1 854625008 Clutch base plate (unit)

2 854111006 Clutch base plate
3 854112007 Clutch starting lever
4 000002105 Snap ring E3
5 854113008 Clutch arm 2
6 854114009 Clutch arm
7 854115000 Clutch arm 2 spring
8 000002507 Snap ring E 4
9 000081005 Setscrew 4x8
10 854626009 Rod (unit)
11 854116001 Rod 1
12 854117002 Rod 2
13 854118003 Rod spring
14 000070230 Washer 3
15 000002301 Snap ring E 2
16 854137008 Clutch arm spring
17 854119004 Clutch releasing arm
18 854120008 Clutch releasing arm guide

7
MC 350E

PARTSLIST
1
12
18

34
20
19
2
30
31

33
32
3

4
5 21

22
6 16
39 13 11
23
35 25
38
15

8
14
37 29 26 24
36 7 10
28

9
12 16 16 27

17

8
MC 350E

PARTSLIST
NO. Parts # Description

1 852009004 Presser bar bushing

2 830030006 Presser bar spring
3 830029002 Presser bar
4 830810042 Embroidery foot P
5 763048006 Setscrew
6 830586035 Presser bar supporter (unit)
7 000111500 Hexagonal socket screw 4x8
8 000116608 Washer 5
9 830035012 Presser foot lifter
10 822072005 Presser foot lifter pin
11 850546002 Thread tension release lever pin (unit)
12 000115629 Setscrew TP 4x8
13 830037025 Thread tension release lever
14 830338007 Thread tension release leverpin
15 000002507 Snap ring E4
16 000081005 Setscrew 4x8
17 830039027 Arm thread guide
18 830585012 Presser foot actuator arm (unit)
19 000014605 Snap ring 6
20 000001609 Snap ring E5
21 852608009 Front bracket (unit)
22 852015003 Front bracket
23 852039025 Lamp set plate
24 501509404 Lamp socket (unit)
25 000115308 Setscrew TP 2x8
26 000103808 Setscrew 3x5
27 851045009 Threader guide plate
28 000026002 Wedge base lamp 12V 5W
29 000111201 Hexagonal socket screw 4x4
30 000061205 Nut 4-3-7
31 830060005 Presser foot actuator shaft
32 830061017 Presser foot actuator arm
33 830062007 Actuator arm
34 830063008 Spring
35 830032019 Presser bar link
36 830034000 Setscrew
37 830033009 Nut
38 830031029 Presser bar supporter
39 102222009 Spring

9
 MC 350E

PARTSLIST
11
18

21

19
20 12
2
11
34
1 9
8
7
6
3
17 35
13
16 10
15
37
37

5 4 36 25
28 29
33
14 27

38 26
24

25

22
30
38
23
32

31

10
MC 350E

PARTSLIST
NO. Parts # Description

1 854639108 Upper shaft (unit)

2 000101703 Setscrew 4x12
3 000078319 Setscrew 3x6
4 000110901 Hexagonal socket screw 5x4
5 000111706 Hexagonal socket screw 5x8
6 829042007 Upper shaft front bushing
7 000038605 Washer 10x0.5
8 639095000 Upper shaft ring
9 000111304 Hexagonal socket screw 5x5
10 830095010 Upper shaft shielding plate
11 820102009 Washer
12 000081005 Setscrew 4x8
13 820511201 Thread take-up lever (unit)
14 650626001 Thread take-up lever pin (unit)
15 650062003 Thread take-up lever pin
16 000001702 Snap ring E6
17 000111201 Hexagonal socket screw 4x4
18 854637003 Upper shaft sensor (unit)
19 854136007 Upper shaft sensor set plate
20 854506002 Printed circuit board P (unit)
21 000101105 Setscrew 3x4
22 000208505 Ball bearing
23 830341003 Upper shaft gear
24 000004303 Knock pin 3x20
25 000024206 Knock pin 3x30
26 502064003 Clutch ring
27 661024007 Clutch spring
28 303025009 Belt wheel
29 000030205 Snap ring E8
30 502068605 Handwheel
31 650071005 Timing belt
32 850165003 Timing belt
33 852629109 Belt wheel (unit)
34 854121009 Upper shaft releasing cam
35 731384008 Felt
36 000208505 Bearing
37 000032609 Snap ring 5103-37
38 854143007 Cushion

11
 MC 350E

PARTSLIST

2 21
3 22

20

15

4 5 23

5
8 13

10
13
11 9
8 14
11
12
10
19
10
18
9 17
16
10 13
25

13
24

12
MC 350E

PARTSLIST
NO. Parts # Description

1 854629002 Hook race (unit)

2 846632003 Bobbin holder stopper (unit)
3 627190010 Magnet
4 000070506 Washer 4
5 000081005 Setscrew 4x8
6 846652102 Bobbin holder (unit)
7 102261103 Bobbin
8 820672005 Lower shaft ring (unit)
9 820166001 Lower shaft ring
10 000111201 Hexagonal socket screw 4x4
11 000038502 Washer 8x0.5
12 650078002 Lower shaft bushing (front)
13 000111304 Hexagonal socket screw 5x5
14 650076000 Lower shaft gear
15 854122000 Lower shaft
16 822112008 Felt holder(1)
17 822070003 Felt (1)
18 000036201 Thrust washer FT 80
19 650079003 Lower shaft bushing (rear)
20 650073007 Lower gear
21 854627000 Lower shaft (unit)
22 000004200 Knock pin 3x18
23 850687006 Lower shaft gear (unit)
24 854628012 Cam (unit)
25 000114802 Setscrew TP 4x12

13
 MC 350E

PARTSLIST

1 19

21
2 22

4
10
23
11
7 12
15
18
17 14
3
20
12
5 6
24
13
13

16
9

16
8 12

14
MC 350E

PARTSLIST
NO. Parts # Description

1 852631001 Front cover (whole unit)(JAI,JCA)

852631104 Front cover (whole unit)(JNBV,JA,JUK,JLA)
2 852016705 Front cover
3 852610004 LCD (unit)
4 852017005 LCD set plate (upper)
5 852611005 LCD set plate (lower) (unit)
6 850612103 Inverter (unit)
7 852505005 LCD harness (unit)
8 852633003 Printed circuit board A (unit)
9 852019018 Card guide
10 852020104 Start/stop button
11 852519002 Printed circuit board F (unit)
12 000120203 Setscrew 3x8(B)
13 852059009 Emblem
14 825183010 Arm thread guide (lower)
15 000096508 Setscrew 3.5x25
16 000115607 Setscrew TP 4x8
17 000066705 Setscrew 3x8
18 832177002 Washer
19 852023004 Front cover cap
20 850524004 Inverter harness (unit)
21 852058101 Button 1
22 852518001 Printed circuit board F2 (unit)
23 852053003 Start/stop button support spring
24 860557007 Ferrite core (JNBV,JA,JUK,JLA)

15
 MC 350E

PARTSLIST
12 27

14 25
1 11
17
21 19 23
2 18
54 16

5 22
36 50 15
20 24
3
11 13
8
6
9
7 10 4

26
29
28
30

35 33 50
11

34 37
40
34 39
41

38
44
43
11
48
32 48
31 42
34
47
45 48
46
51
49 11

53
52

11

43

16
MC 350E

PARTSLIST
NO. Parts # Description

1 854640009 Bobbin winder (unit)

2 852509009 Bobbin winder (unit)
3 823119008 Spring
4 854140004 Bobbin winder set plate
5 000001609 Snap ring E5
6 852615009 Bobbin winderswitch (unit)
7 852510003 Micro switch (unit)
8 852042009 switchset plate2
9 852014002 Insulation paper
10 000041209 Setscrew 1.7x6
11 000081005 Setscrew 4x8
12 852637018 Rear cover (unit)(JAI,JCA,JNBV,JA,JUK)
852637100 Rear cover (unit)(JLA)
13 852002100 Rear cover (JAI,JCA,JNBV,JA,JUK)
852002605 Rear cover (JLA)
14 650503702 Thread guide (unit)
15 000014409 Snap ring CS8
16 834555107 Top cover thread guide plate (unit)
17 000162001 Setscrew 2.6x5
18 000024804 Spring pin 2x12
19 840602109 Thread cutter (unit)
20 000014306 Snap ring CS3
21 659067005 Additional spool pin
22 505062000 Bobbin winder stopper
23 000101828 Setscrew 4x16
24 000061205 Nut4-3-7
25 000103200 Setscrew 4x30
26 000115205 Setscrew TP 4x6
27 653006101 Cap
28 853021005 Rear cover set plate
29 850201002 Carriage sticker
30 850628205 Switching power supply (unit)
31 850541203 Switching power supply (unit)
32 850157024 Swithcing power supply case
33 850158014 Switching power supply cap
34 000119704 Setscrew 3x14(B)
35 850523003 Power supply harness (unit)
36 810220106 Setscrew
37 854633009 Driving arm shaft base (unit)
38 860045007 Driving arm shaft base
39 846233000 Driving arm (1)
40 846154006 Spring
41 000002507 Snap ring E4
42 854133004 Thread cutter starting lever
43 000002105 Snap ring E3
44 860624109 Thread cutter sensor (unit)
45 860047009 Thread cutter sensor set plate
46 846513605 Micro switch (unit)
47 000102900 Setscrew 2x8
48 000053606 Cord binder
49 000101105 Setscrew 3x4
50 000115607 Setscrew TP 4x8
51 854632008 Thread cutter solenoid (unit)
52 854131002 Thread cutter starting rod
53 000005304 Knock pin 3x8
54 854641000 Bobbin winder (unit)

17
MC 350E

PARTSLIST

1
3
2
3
5

24
21
4

6
11
8
5
3
23
12 7
22 3

25
26 3
10

13 9 30
14 27
29
31
28
3

15
16
17
18

19

20
3

18
MC 350E

PARTSLIST

NO. Parts # Description

1 852634004 Thread cutter (unit)

2 860625007 Thread cutter (unit)
3 000081005 Setscrew 4X8
4 852057007 Thread cutter cover set plate
5 000101105 Setscrew 3X4
6 854631007 Needle thread solenoid (unit)
7 854508004 Needle thread solenoid (unit)
8 854127005 Solenoid set plate
9 000163806 Setscrew 2.6X4
10 854128006 Thread drawing leverArm
11 000003900 Knock pin 2.5X8
12 854129007 Thread drawing lever actuator plate
13 854130001 Spring
14 000002507 Snap ring E4
15 852050000 Thread tension release lever spring
16 850645013 Bobbin thread sensor solenoid (unit)
17 832613027 Bobbin thread sensor solenoid (unit)
18 850083006 Bobbin thead detect arm
19 000002105 Snap ring E3
20 846220004 Setscrew
21 850618109 Sensor set plate (unit)
22 000013707 Snap ring CS 2.4
23 850089002 Safety spring
24 850212017 Arm spring
25 854636002 Presser foot lifter switch (unit)
26 852621008 Presser foot lifter switch (unit)
27 852510106 Micro switch (unit)
28 852013001 Switch set plate 1
29 852014002 Insulation paper
30 000041209 Setscrew 4X8
31 854135006 Presser foot lifter switch base plate

19
MC 350E

PARTSLIST

12

6 5

7
5
22 9
10
13
10

24
1

2 9
14
3 8
4
18 11
17

26 5
25
15
5
20

23
11
16

21
19

20
MC 350E

PARTSLIST
NO. Parts # Description

1 851617008 Idler (unit)

2 851039000 Idler base
3 625217100 Idler
4 000002806 Snap ring E6
5 000081005 Setscrew 4x8
6 852032006 Carrying handle supporter (rear)
7 853614207 Belt cover (unit)
8 852031304 Belt cover
9 832099009 Belt cover attaching plate(1)
10 000161103 Setscrew 3x6(B)
11 000078319 Setscrew 3x6
12 000115009 Setscrew TP 3x8
13 000104108 Setscrew 4x20
14 653006101 Cap
15 852513006 Machine socket (unit)(JAI,JCA)
852514007 Machine socket (unit)(JNBV,JA,JUK,JLA)
16 000107802 Setscrew 3x10(B)
17 852036000 Machine socket set plate
18 810220106 Setscrew
19 000101817 Setscrew 4x16
20 852620030 DC Motor (unit)
21 000115607 Setscrew TP 4x8
22 854139003 Carrying handle
23 852512108 DC Motor (unit)
24 853022006 Connector cover
25 857025001 Motor setting support plate
26 000101404 Setscrew 4x6

21
 MC 350E

PARTSLIST

12
10 11

14
13

15

16

18
17

9 8
8 8
4
20
21
3
2
5
19 6

22
MC 350E

PARTSLIST
NO. Parts # Description

1 852617104 Base (unit)

2 830150003 Rubber foot
3 820350004 Adjusting screw
4 820351005 Spring
5 605074008 Rubber foot
6 813123004 Snap ring CS
7 850151017 Base lid
8 810220106 Setscrew
9 832146002 Base lid (1)
10 851053103 Base cover
11 000101426 Setscrew 4x6
12 000101127 Setscrew 3x4
13 850147205 Sheet cover
14 000066727 Setscrew 3x8
15 850627101 Carriage plate (unit)
16 850169007 Cover 2
17 000078319 Setscrew 3x6
18 850156001 Cover
19 000127107 Setscrew 6x35
20 851071015 Base lid (3)
21 717618000 Adjusting screw (unit)

23
MC 350E

PARTSLIST
1

2 3 4 5 6

7 8 9 10 11

13 14 15
12

16 17 18

19

24
MC 350E

PARTSLIST

NO. Parts # Description

1 852801004 Standard accessories (unit)

2 102261103 Bobbin
3 102403109 Felt
4 802424004 Lint brush
5 820832005 Screwdriver (large)
6 822814007 Scissors
7 625031500 Additional spool pin
8 822019509 Spool holder (small)
9 852802108 Needle (unit)
10 829803004 Spool stand
11 653802002 Screwdriver
12 822020503 Spool holder (large)
13 852850008 Instruction book (unit)(JAI)
852850101 Instruction book (unit)(JCA)
852850204 Instruction book (unit)(JNBV)
852850307 Instruction book (unit)(JA)
852850400 Instruction book (unit)(JUK)
852850503 Instruction book (unit)(JLA)
14 852852000 Template sheet (unit)
15 653524007 Power supply cord(JAI,JCA)
830314018 Power supply cord(JA)
830377008 Power supply cord(JUK)
830335004 Power supply cord(JNBV,JLA)
16 852807011 Embroidery hoop A (whole unit)
17 850802010 Embroidery hoop B (whole unit)
18 852853001 Instructional CD (JAI,JCA,JNBV,JA,JUK)
19 852806009 Dust cover

25