Scribd
Upload
19 views

Asset 1st Batch Level III

Uploaded by

Nayeem Hossain
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
19 views

Asset 1st Batch Level III

Uploaded by

Nayeem Hossain
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Bangladesh German Technical Training Center

Mirpur-2, Dhaka-1216
Trade: PLC
ASSET 1st Batch (January-April)-2024, Level - III
Date: 27-04-2024

✓
1. What is equivalent of 1KΩ ?
a) 1000Ω b) 100Ω c) 10Ω d) 10000Ω
2. Which one is the write platform to ping ?
a) Command window b)control panel c) command prompt d) control window
3. The output voltage of thermocouple is ….
a) DC Voltage b) AC Current c) AC Voltage d) DC mVoltage

4. What is ?
a)Break contact b) Make contact c) Analog contact
5. What is (/) ?
a) Coil b) Inverted coil c) NO d) NC
6. ……. is not a signal control element?
a) Pneumatic electric b) Potentiometer c) Solenoid Valve d)
7. Which one is the above sign?
a) Sine wave b) Square wave c) Triangle d) Exponential
8. Draw the square wave.
Ans:

9. What is the ratio of lead and tin?


Ans: Lead 60% Tin 40%
10. What is the market name of SPDT?
Ans: 2-way switch
11. What is the market name of DPDT?
Ans: Intermediate Switch
12. What is soft starter?
Ans: A soft starter is a device that starts motor with reduce power supplied at start-up.
13. Write down the two types of proximity sensor.
Ans: I) Inductive II) Capacitive
14. What are types of PLC by I/O configurations?
Ans: I) Relay type II) Transistor type
15. Write down the two common type of temperature sensor.
Ans: RTD & Thermocouple
16. What is Solenoid valve?
A Solenoid valve is an electrically controlled valve, the value features a Solenoid which
is an electric coil with a ferromagnetic core in center.
17. What is timer relay?
Ans: A timer relay is a combination of an electromechanical output relay and a control
circuit. The contacts will open or close or after a pre-selected time.
18. What do you mean by proximity sensor?
Ans: Proximity sensor detects presence of an object.
19. What is limit switch?
Ans: Limit switch is a switch operated by the motion of a machine.
20. What is relay?
Relay is an electromechanical switch.
21. What is VFD?
Ans: A Variable Frequency Drive is a combination of an electronics and power
electronics devices that used to vary voltage and frequency.
22. What do you understand by 1.2rm wire?
Ans: Round multiple wire whose cross-sectional area of each core is 1.2mm².
23. How do you explain ladder diagram?
Ans: Ladder diagram are specialized schematics commonly used to document PLC
logic.
24. How do you explain device manager?
Ans: Device manager is a control panel in Microsoft windows operating system. It
allows users to view and control the hardware attached to the computer.
25. What is process variable of a controller?
Ans: A process variable, process value or process parameter is the current measured
value of a particular part of a process which is being monitored or controlled.
26. What is open loop control system?
Ans: One type of control system in which the output has no influence or effect on the
control action of the input signal.
27. What does it mean by PT100?
Ans: It means ohomic value 100 ohms at 0 degree centigrade.
28. What is Magnetic Contactor?
Ans: A magnetic contactor is a special type of relay used for switching and electrical
current ON or OFF.
29. What is MCCB?
Ans: Moulded case circuit breaker, which is used when load current exceeds the limit of
MCB.
30. What is Motor?
Ans: Motor is an electrical machine that converts electrical energy to mechanical energy.
Oral Question
1. Tell three types of analog sensor
2. Tell type of analog signal used in PLC
3. Tell two types of analog output device
4. Difference between Relay and Magnetic Contactor
5. Describe the function of different Timer (i.e. On delay, Off delay)
6. What are the different components of a PLC?

Oral Question
1. Temperature sensor, Level Sensor, RPM sensor
2. 0-10V DC and 4-20mA
3. Inverter/VFD, Analog valve
4. Actually, the mechanism of the relay and magnetic contactor are same but relay is
used to handle low current and to make some logical flow wherein Magnetic
Contactor is used to handle the heavy load i,e 3 phase induction motor.
5. The main function of the timer is to apply delay between its input signal state and
output signal state. If the delay applied to its input ON state that to ON state that is
called ON delay timer.
On the other hand, if the delay applied to its input OFF state to output OFF state
that is called Off delay timer.
6. I/O interface, CPU, Memory, Programming tool.
Bangladesh German Technical Training Center
Mirpur-2, Dhaka-1216
Trade: PLC
ASSET 1st Batch (January-April)-2024, Level - III
Date: 05-05-2024

1. What is equivalent of 1✓µf?


a) 10-3 F b) 10-6 F c) 106 F d) 1012 F

2. Which type of 24 V DC power supply used in PLC


A) SMPS B) Regulated power supply C) AC power supply D) All

3. How do you measure voltages in a circuit?


A) Series of a load B) Parallel of a load
C) Combination of series and parallel D) None of the 3

4. How do you measure current of a circuit

A) Series of a load B) Parallel of a load


C) Combination of series and parallel D) None of the 3

5. What is equivalent of 1mH?

A) 103 H B)10-3 H C) 106 H D) 105 H

6. name the switch?

A) Push button, NO B) Push button, NC

C) Change over D) None of the three

7. name the switch?

A) Push button, NO B) Push button, NC

C) Change over D) None of the three


8. Which one below is the symbol for relay?

A) B) C) D)√

9. Which one below is the symbol for On-delay timer?

A) √ B) C) D)

10. Which one below is the symbol for Solenoid coil?

A) B) √ C) D)

11. PLC is an acronym of……………. logic.

A) Programmable B) Peripheral

C) Periodic D) Pneumatic

12. What is ?

A) Break Contact B) Make Contact C) Analog Calculator

13. Whate is the commonly used working DC voltage in electronics.

A) 3v B) 12v C) 3v, 12v D) 3v, 5v

14. Which one is the write platform to ping?

A) Command window B) Control Panel

C) Command prompt D) Control window


15. Which one below is the symbol for Solenoid coil?

A) B) √ C) D)

(Answer in short)-

16. Describe the function of the above circuit.

Ans: It's a latching circuit or an inter-locking circuit. When push switch S1 pressed the relay K1
will on and remain ON until the push button, NC is pressed.

17. What are the ratio of lead and tin?

Ans: Lead 60% and Tin 40%

18. What is mean of proximity sensor?

Ans: 18. Proximity sensor detects presence of an object.

19. What is limit switch?

Ans: Limit switch is a switch operated by the motion of a machine.

20. Name some PPE for your related job?

Ans: Hand gloves, Apron, Safety shoes.

21. How do you Explain ladder diagram?

Ans: Ladder diagram are specialized schematics commonly used to document PLC logic.
22. How would you explain device manager?

Ans: Device manage is a control panel in Microsoft windows operating system. It allows users to
view and control the hardware attached to the computer.

23. How do you communicate PLC with a PC?

Ans: RS-232, RS-485, TCP/IP, USB etc.

24. What is on/off or 2 steps control system?

Ans: On-off control uses a feedback controller that switches abruptly between two states.

25. What is set point of a controller?

Ans: Set point is the target value at which a controller attempts to maintain the process variable.

26. What is a feed back of a controller?

Ans: A feedback controller measures the output of a process and then manipulates the input as
needed to drive the process variable toward the desired setpoint.

27. What is process variable of a controller?

Ans: A process variable, process value or process parameter is the current measured value of a
particular part of a process which is being monitored or controlled.

28. What is motor?

Ans: Motor is an electrical machine that convert electrical energy into mechanical energy.

29. What is Magnetic Contactor?

Ans: A Magnetic Contactor is a special type of relay used for Switching and electrical circuit
ON or OFF.

30. What are types of PLC by 1/0 configurations.

Ans: I) Relay type II) Transistor type

You might also like