RE 64 551/03.

94

Pilot Device in Pedal Design

Type 2 TH 6 R, Series 1X
RE
for the Remote Control of 64 551/03.94
Replaces: 07.92
Directional Valves, Pumps and Motors
Features:
– Progressive, sensitive operation
– Precise control
– Working ports underneath
– Protection of control elements by means of rubber sleeves
– Push rods made of stainless steel, push rod bush of brass;
hence prevention of corrosion and abrasion

Other pilot control devices

– Control device model 2 TH5 (see RE 64 550 and model
2 TH6 in sandwich plate construction (see RE 64 552)
– Type 4 TH6 for installation in arm rests (see RE 64 555)
– Type TH7 pilot control devices for installation in control panel
or for pedal operation (see RE 64 558)
– Type 4/5 THF6 with end position locking (see RE 64 553)
H/C 2926
– Electronic remote control type THE6 for direct control of
Type 2 TH 6 R ...
electric or electro-hydraulic pilot controlled actuators (see
RE 29 771)
– Electronic remote control type THEF6 with end position
locking (see RE 29 783)
– Programmable electronic signal transmitters type THES6
(see RE 29 792)
When foot pedal (1) is depressed, push rod (5) is pressed
Functional Description against return spring (4) and control spring (3). Control spring (3)
initially moves control spool (2) downwards and closes the
connection between the relevant port and tank port T. At the
Hydraulic remote controls, type 2 TH 6 R... operate as pressure
same time the relevant port is connected to port P via bore (7).
reducing valves.
The control phase starts as soon as control spool (2) finds its
They basically comprise foot pedal (1), two pressure reducing
balance between the force of control spring (3) and the force,
valves and housing (6).
resulting from the hydraulic pressure in the relevant port (port 1
Each pressure reducing valve comprises control spool (2),
or 2).
control spring (3), return spring (4) and push rod (5).
Due to the interaction between control spool (2) and control
At rest the foot pedal is held in its neutral position by return
spring (3), the pressure in the relevant ports is proportional to the
springs (4). Ports (1,2) are connected to tank port T via bore (7).
stroke of push rod (5) and hence to the position of pedal (1).
This closed loop pressure control dependent on the position of
foot pedal (1) and the characteristics of control spring (3) permits
the proportional hydraulic control of directional valves and
control valves for hydraulic pumps and motors.

5 3
T 4
7
6
P 2

1 2

1/4
RE 64 551/03.94

Symbol
T P

1 2

Technical data (For operation outside these parameters, please consult us!)

Fluid Mineral oils (HL, HLP) to DIN 51 524; phosphate ester (HFD-R)
Fluid temperature range °C – 20 to + 80
Viscosity range mm2/s 10 to 380
Fluid cleanliness Maximum permissible degree of contamination of fluid to NAS 1638 Class 9.
We therefore recommend a filter with a minimum retention rate of β10 ≥ 75.
Max. input pressure bar max. 50
Counter pressure at port T bar max. 3
Pilot flow L/min max. 16
Hysteresis bar max. 1
Weight kg approx. 3,8
Maximum permitted operating daNm 20
moment at pedal
Maximum permitted operating daNm 12
moment at a built-on manual operating lever
Operating curves: control ranges, operating forces
p
Control range – operating curve 06
Input pressure

19 +3
Control pressure in bar

15

10

5,8 –0,7

0 2 4 6 8 10 12
Operating torque Pedal depression in degrees
M
for control curve 06,
return spring 19 956 700 11,5
and inlet pressure 50 bar 11
10
9
Operating torque in Nm

6
5,5
5
4

0 2 4 6 8 10 12
Pedal depression in degrees

2/4
 RE 64 551/03.94

Ordering Code

2 TH6 R 1X *
2 control ports =2 Further details in clear text
Pedal operation =R Connecting thread
Pedal model 01 = 1/4" BSP thread ISO 228/1
Bent pedal =C 02 = M 14 x 1,5
Flat pedal =P 05 = 9/16 - 18" UNF
Standard control range/operating curve = 06 Seals
Series 10 to 19 = 1X M= NBR seals, suitable for use with mineral
(10 to 19, externally interchangeable) oils (HL, HLP) to DIN 51 524
V= FPM seals, suitable for use with
phosphate ester (HFD-R)

Unit dimensions: flat pedal "P" (Dimensions in mm)

180
160 4 x Ø93 Ordering Ports P, T, 1 and 2
2 x Ø25+0,3; 0,8 – 1 code
01 1/4" BSP to ISO 228/1
02 M14 x 1,5
05 9/16 - 18" UNF

= =
40
7

2
80 118
°
12

24 24
4 = =
56
12°

26 5 Ø16,5

16
1

24
ca. 180
approx. 180

M12
2 x Ø25+0,3; 0,8 – 1
94
121

T
96

94

T T T

P
58,5

P P P
31

1 2

105 = =
6 32

1 Position 1
(port 1 pressurised)
=

2 Position 2
72
70

(port 2 pressurised)
=

3 Fixing holes
4 Pedal depression
130 5 setting screw
24 6 Safety foot rest
282
7 Fixation manual operating lever

3/4
RE 64 551/03.94

Unit dimensions: bent pedal "C" (Dimensions in mm)

Ordering Ports P, T, 1 and 2

code
01 1/4" BSP to ISO 228/1
180
160 02 M14 x 1,5
4 x Ø9 3
2x Ø25+0,3; 0,8-1 05 9/16 - 18" UNF

37
20
40

74
1 2

4 ° 2 7 120
12 80 28
56
°
12

15°
1
Ø16 +0,5
M12

5
30
300
ca. 300
approx.

2 x Ø25+0,3; 0,8 – 1
121

T
96

94

T T T
58,5

P
P P P
31

1 2

105 16
150 32
6
1 Position 1
(port 1 pressurised)
2 Position 2
38

(port 2 pressurised)
76

3 Fixing holes
4 Pedal depression
5 setting screw
6 Safety foot rest

310 7 Fixation manual

operating lever

Mannesmann Rexroth GmbH Mannesmann Rexroth Limited

D-97813 Lohr am Main Cromwell Road, St. Neots,
Jahnstraße 3-5 • D-97816 Lohr am Main Huntingdon, Cambs. PE19 2ES
Telefon 0 93 52 / 18-0 • Telefax 0 93 52 / 18-10 40 Tel: (01480) 476041
Telex 6 89 418-0 Fax: (01480) 219052
The specified data is for product description purposes only and may not be deemed to be
4/4 guaranteed unless expressly confirmed in the contract. All rights reserved – Subject to revision