Scribd
Upload
9 views

IP Telephony Basic Configuration Using P2 - Copy - Copy

IP Telephony Basic Configuration Using P2

Uploaded by

mirtech2018
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
9 views

IP Telephony Basic Configuration Using P2 - Copy - Copy

IP Telephony Basic Configuration Using P2

Uploaded by

mirtech2018
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

12/24/2017 IP telephony basic configuration Using Packet Tracer

IP telephony basic configuration Using Packet Tracer BY MD NURUL AKTER ON 11


AUGUST 1, 2013 CCNA

Tutorial description

This tutorial is designed to help you to configure the new voice over ip (voip) features available in Packet Tracer 5.3. It will
the steps required to :

Configure Call Manager Express on a Cisco router


Use the various telephony devices
Setup dial peers
Connect Cisco IP phones as well as analogue phone on the network.

Network diagram

Tasks 1 : Configure interface FastEthernet 0/0 and DHCP server on RouterA

#Configure the FE 0/0 interface#

RouterA>enable

RouterA#configur □ terminal

RouterA(config)#interface □ FastEthernet □ 0/0

http://technews365.info/ip-telephony-basic-configuration-packet-tracer/ 1/4
12/24/2017 IP telephony basic configuration Using Packet Tracer

RouterA(config-if)#ip □ address □ 192.168.1.1 □ 255.255.255.0

RouterA(config-if)#no □ shutdown

Note: The DHCP server is needed to provide an IP address and the TFTP server location for each IP phone.

RouterA(config)#ip □ dhcp □ pool □ VOICE [Create DHCP pool named VOICE]

RouterA(dhcp-config)#network □ 192.168.10.0 □ 255.255.255.0 [DHCP network, network 192.168.10.0]

RouterA(dhcp-config)#default-router □ 192.168.10.1 [The default router IP address]

RouterA(dhcp-config)#option □ 150 □ ip □ 192.168.10.1 [Mandatory for voip configuration.]

Note: After the configuration, wait a moment and check that ‘IP Phone 1’ has received an IP address until a configuration
summary appears.

Tasks 2 : Configure the Call Manager Express telephony service on RouterA

You must now configure the Call Manager Express telephony service on RouterA to enable voip on your network.

RouterA(config)#telephony-service [Configuring the router for telephony services]

RouterA(config-telephony)#max-dn □ 5 [Define the maximum number of directory numbers]

RouterA(config-telephony)#max-ephones □ 5 [Define the maximum number of phones]

RouterA(config-telephony)#ip □ source-address □ 192.168.10.1 □ port □ 2000 [IP Address source]

RouterA(config-telephony)#auto assign □ 1 □ to □ 5 [Automatically assigning ext numbers to buttons]

Task 4 : Configure a voice vlan on SwitchA

Apply the following configuration on SwitchA interfaces. This configuration will separate voice and data traffic in different
vlan SwitchA. data packets will be carried on the access vlan.

SwitchA(config)#interface range □ fa0/1 – 5 [Configure interface range]

SwitchA(config-if-range)#switchport □ mode □ access

SwitchA(config-if-range)#switchport □ voice □ vlan □ 1 [Define the VLAN on which voice packets will be handled]

Task 5 : Configure the phone directory for IP Phone 0

http://technews365.info/ip-telephony-basic-configuration-packet-tracer/ 2/4
12/24/2017 IP telephony basic configuration Using Packet Tracer

Although ‘IP Phone 0’ is already connected to SwitchA, it needs additionnal configuration before beeing able to
communicate. You need to configure RouterA CME to assign a phone number to this IP phone.

RouterA(config)#ephone-dn □ 1 [Defining the first directory entry]

RouterA(config-ephone-dn)#number □ 54001 [Assign the phone number to this entry]

Task 6 : Verify the configuration

Ensure that the IP Phone receives an IP Address and a the phone number 54001 from RouterA (this can take a short
while).

Task 6 : Configure the phone directory for IP Phone 1

Connect IP Phone 2 to SwitchA and power the phone ON using the power adapter (Physical tab).

RouterA(config)#ephone-dn □ 2 [Defining the first directory entry]

RouterA(config-ephone-dn)#number □ 54002 [Assign the phone number to this entry]

http://technews365.info/ip-telephony-basic-configuration-packet-tracer/ 3/4
12/24/2017 IP telephony basic configuration Using Packet Tracer

Task 7 : Configure the phone directory for IP Phone 2

Connect IP Phone 2 to SwitchA and power the phone ON using the power adapter (Physical tab).

RouterA(config)#ephone-dn □ 3 [Defining the first directory entry]

RouterA(config-ephone-dn)#number □ 54003 [Assign the phone number to this entry]

– ————————– Thanks

http://technews365.info/ip-telephony-basic-configuration-packet-tracer/ 4/4

You might also like