SCHEDULD OF QUANTITY

Name of Work:- Construction of 87 Nos. (Combined Quarters Type-II/43 Nos. & Type- III/28 Nos., Combined Quarters Type-IV/8 Nos. & Type-V/7
Nos. and Type-VI/1 No.) Residential Quarters, GO's Mess, SO's Mess and Community Centre for CISF at Rajarhat, Kolkata. SH: Furnishing of
Modular kitchens for Type-IV/8 Nos. & Type-V/7 Nos. and Type-VI/1 No. of Residential complex for CISF at Rajarhat, Kolkata.

SL. Specification Qty Unit Rate Amount Reference Image

TYPE- IV KITCHEN - 8 nos
1 Providing, Supplying, installation & furnishing of factory made linear moduflex
kitchen from manufacturers certified with ISO 9001:2015, ISO 50001:2018,
ISO45001:2018, ISO 14001:2015 (all ISO must be from NABCB/IAF accredited
agency), BIFMA (LEVEL 2), IAQ, IGBC PLlatinum, Indoor Air Advantage Gold,
Greenguard (by UL), Greenpro, Griha 2019. as per approved drawing and design/
specification of Engineer In-Charge. Overall dimensions of undercounter deck : 2815
(L) X 560 (D) X 690 (H) mm. two nos. of Overhead cabinet: 3nos. 500 (L) X 310 (D)
X 600 (H) mm.(without soft closing hinges & channels)
Not in Scope: Chimney ,Sink & accessories, water filtration, Premoulded & prepolished
granite top kitchen counter, Flooring , painting, wall tiles, power and gas connections
& other civil, plumbing & electrical works.

8 each 1,69,950 13,59,600

Base Cabinets
1.1 Double shutter Floor Sink unit (1000w X 540d X 690h)mm
Supply, installation & placement of Kitchen Floor sink unit. Cabinet Material: 18mm thk.
Prelaminated BWR (IS-303) plywood panels with balancing matte Ral white laminate finish
inside (Body panels) and the carcase of floor units will be supported by 100mm H vertical
ajustable legs upto 20 mm which will be covered with PVC skirting in brushed aluminium finish
attached by hardware of skirting .Unit Construction: Floor units will be made using
Prelaminated BWR plywood (Grade IS-303) panels with 1 mm. thk. decorative laminate finish
connected with fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent.
Shutters: 18mm thk. prelaminated Marine ply of grade (IS- 710). Finish on shutter surface:
1mm thk. decorative laminate finish both side with 2mm(+/- 0.1) thk. edge banding of Rehau
or equivalent. Hinges: Auto hinge of Hettich or equivalent with CED coating for extended
corrosion resistance. Opening angle of hinge : 95° for door thickness of 15mm-22mm provided
with mounting plates, with 35mm cup diameter. Each shutter should be connected with the
carcase with 2nos of hinges. Skirting : Rehau make PVC Co-extruded skirting attached with the
carcase.(Height: 100mm). Shelves: 18mm thk both side laminated Prelaminated BWR grade (IS
- 303) shelf on one side of the cabinet (500mm L x 300mm D) connected with fasteners with
1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Handles: Arch Handles(1nos. for
each shutter) 128 mm pitch made of Zinc alloy diy cast handle with satin finish. Dustbin Holder-
1nos. 250mm(+/-5%) dia 3mm thk SS wire mounted on hinged door . SS sink not included.
(Actual dimensions may vary upto +/-5% as per site measurements).

8 Nos
1.2 Gas cylinder cabinet (400w X 540d X 690h)mm

Page 1 of 15
 Supply, installation & placement of Kitchen (single capacity) Gas cylinder cabinet .
Cabinet Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with
balancing matte Ral white laminate finish inside for top & side panels (Body panels).
Unit Construction: Floor units will be made using Prelaminated BWR plywood (Grade
IS-303) panels with 1 mm. thk. decorative laminate finish connected with fasteners
with 1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Shutters: 18mm thk.
Marine ply of grade (IS- 710) made shutters. Finish on shutter surface: 1mm thk.
decorative laminate finish both side with 2mm(+/- 0.1) thk. edge banding of Rehau or
equivalent. Hinges: Auto hinge of Hettich or equivalent with CED coating for
extended corrosion resistance. Opening angle of hinge : 95° for door thickness of
15mm-22mm provided with mounting plates, with 35mm cup diameter. Each shutter
should be connected with the carcase with 2nos of hinges. Skirting : Rehau make
PVC Co-extruded skirting attached with shutters. (Height: 100mm). Handles:
Handles: Arch Handles(1nos. for each shutter) 128 mm pitch made of Zinc alloy diy
cast handle with satin finish. Gas trolley- 1nos. 280mm(+/-5%) dia 3mm thk SS wire
trolley with 4nos ABS castors . (Actual dimensions may vary upto +/-5% as per site
measurements)

8 Nos
1.3 Three drawer dish unit (600w X 540d X 690h)mm
Supply, installation & placement of Kitchen three drawer dish unit . Cabinet Material:
18mm thk. Prelaminated BWR (IS-303) plywood panels with balancing matte Ral white
laminate finish inside (Body panels) and the carcase of floor units will be supported by
100mm (H) vertical ajustable legs upto 20 mm which will be covered with PVC skirting in
brushed aluminium finish attached by hardware of skirting . Unit Construction: Floor units
will be made using Prelaminated BWR plywood (Grade IS-303) panels with 1 mm. thk.
decorative laminate finish connected with fasteners with 1.2mm(+/- 0.1) thk. edge
banding of Rehau or equivalent. Drawer size: Drawer 1 (600mmL x 520mmD x 100mmH)
with Prelaminated BWR plywood (Grade IS-303) inside structure with cutlery organiser,
Drawer 2: (600mmL x 520mmD x 100mmH) with SS wire basket for cup/ bowls upto
100mm high, Drawer 3:(600mmL x 520mmD x 250mmH)with wire basket for Plates / Dish
placement. Drawer with cuttlery tray: The cabinet will be consisting of SS-304 Grade i/c
Cutlery Basket +Cup & Saucer 100 mm + Thali Bskt 150 mm with 600m width , and
fittings required SS screw for fixing above quadro slide of hettich or eq . Finish on drawer
front fascia : 1mm thk. decorative laminate finish both side on 18mm thk. Marine ply of
grade (IS-710) with 2mm(+/- 0.1) thk edge banding of Rehau or eq. Overall dimensions of
drawer front: Drawer 1: (600mmL x 520mmD x 162.5mmH), Drawer 2: (600mmL x
520mmD x 162.5mmH), Drawer 3 (600mmL x 520mmD x 325mmH). Ball slide Telescopic
Drawer Channel: Manufactured from CRCA steel for longevity. Black Powder Coated for
extended corrosion resistance made of Hettich or equivalent .Black Powder Coated for
better corrosion resistance. Colour: Black. Finish: Type Glossy. Weight Limit: 45 Kilograms.
Length- 300mm. Skirting : Rehau make PVC Co-extruded skirting. (Height: 100mm).
Handles: Arch Handles(1nos. for each drawer) 128 mm pitch made of Zinc alloy diy cast
handle with satin finish. (Actual dimensions may vary upto +/-5% as per site
measurements).

8 Nos
1.4 Single shutter plain shelf unit (600w X 540d X 690h)mm

Page 2 of 15
 Supply, installation & placement of Kitchen single shutter plain shelf unit. Cabinet
Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with balancing
matte Ral white laminate finish inside (Body panels) and The carcase of floor units
will be supported by 100mm H vertical ajustable legs upto 20 mm which will be
covered with PVC skirting in brushed aluminium finish attached by hardware of
skirting . Unit Construction: Floor units will be made using Prelaminated BWR plywood
(Grade IS-303) panels with 1 mm. thk. decorative laminate finish connected with
fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Shutters:
18mm thk. Marine ply of grade IS- 710. Finish on shutter surface: 1mm thk.
decorative laminate finish both side with 2mm(+/- 0.1) thk. edge banding of Rehau or
equivalent. Shelves: 18mm thk both side laminated Prelaminated BWR grade (IS -
303) shelf inside of the cabinet (600mm L x 540mm D) connected with fasteners with
1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Hinges: Auto hinge of
Hettich or equivalent with CED coating for extended corrosion resistance. Opening
angle of hinge : 95° for door thickness of 15mm-22mm provided with mounting
plates, with 35mm cup diameter. Each shutter should be connected with the carcase
with 2nos of hinges. Skirting : Rehau make PVC Co-extruded skirting attached with
shutters. (Height: 100mm). Handles: Handles: Arch Handles(1nos. for each shutter)
128 mm pitch made of Zinc alloy diy cast handle with satin finish.(Actual dimensions
may vary upto +/-5% as per site measurements)

8 Nos
Overhead Wall Unit
1.5 Overhead single shutter plain shelf unit (500w X 310d X 600h)mm
Supply, installation & placement of Kitchen overhead plain shelf unit with M ply
shutter. Cabinet Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with
balancing matte Ral white laminate finish inside (Body panels). Unit Construction:
overhead units will be made using Prelaminated BWR plywood panels with 1 mm. thk.
decorative laminate finish connected with fasteners with 1.2mm(+/- 0.1) thk. edge
banding of Rehau or equivalent. Shutters: 18mm thk. Marine ply of grade IS- 710.
Finish on shutter surface: 1mm thk. decorative laminate finish both side with 2mm(+/-
0.1) thk. edge banding of Rehau or equivalent. Shelves:The cabinet will be consisting
of adjustable shelves that shall be supported on approved quality SS pins and shall be
adjustable for different heights as per requirement. 18mm thk both side laminated
Prelaminated BWR grade (IS - 303) shelf inside of the cabinet connected with
fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Hinges:
Auto hinge of Hettich or equivalent with CED coating for extended corrosion
resistance. Opening angle of hinge : 95° for door thickness of 15mm-22mm provided
with mounting plates, with 35mm cup diameter. Each shutter should be connected
with the carcase with 2nos of hinges. Handles: Arch Handles(1nos. for each shutter)
128 mm pitch made of Zinc alloy diy cast handle with satin finish. The unit shall be
fixed to the wall using metal screws of appropriate size and rawl plugs. (Actual
dimensions may vary upto +/-5% as per site measurements)

24 Nos

2.0 TYPE- V KITCHEN - 7 nos

Page 3 of 15
 Providing, Supplying, installation & furnishing of factory made L shape moduflex
kitchen from manufacturers certified with ISO 9001:2015, ISO 50001:2018,
ISO45001:2018, ISO 14001:2015 (all ISO must be from NABCB/IAF accredited
agency), BIFMA (LEVEL 2), IAQ, IGBC PLlatinum, Indoor Air Advantage Gold,
Greenguard (by UL), Griha 2019. as per approved drawing and design/
specification of Engineer In-Charge. Overall dimensions of undercounter deck :
(4230+1272) (L) X 560 (D) X 690 (H) mm. , 2nos. of Overhead cabinet: 2nos. 1000
(L) X 310 (D) X 600 (H) mm. (without soft closing hinges & channels). Not in Scope:
Chimney ,Sink & accessories, water filtration, Premoulded & prepolished granite top
kitchen counter, Flooring , painting, wall tiles, power and gas connections & other
civil, plumbing & electrical works.

7 Each 2,49,290 17,45,030

2.1 Double shutter Floor Sink unit (900w X 540d X 690h)mm
Supply, installation & placement of Kitchen Floor sink unit. Cabinet Material: 18mm
thk. Prelaminated BWR (IS-303) plywood panels with balancing matte Ral white
laminate finish inside (Body panels) and the carcase of floor units will be supported
by 100mm H vertical ajustable legs upto 20 mm which will be covered with PVC
skirting in brushed aluminium finish attached by hardware of skirting .Unit
Construction: Floor units will be made using Prelaminated BWR plywood panels with 1
mm. thk. decorative laminate finish connected with fasteners with 1.2mm(+/- 0.1)
thk. edge banding of Rehau or equivalent. Shutters: 18mm thk. prelaminated Marine
ply of grade (IS- 710). Finish on shutter surface: 1mm thk. decorative laminate finish
both side with 2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Hinges: Auto
hinge of Hettich or equivalent with CED coating for extended corrosion resistance.
Opening angle of hinge : 95° for door thickness of 15mm-22mm provided with
mounting plates, with 35mm cup diameter. Each shutter should be connected with
the carcase with 2nos of hinges. Skirting : Rehau make PVC Co-extruded skirting
attached with the carcase.(Height: 100mm). Shelves: 18mm thk both side laminated
Prelaminated BWR grade (IS - 303) shelf on one side of the cabinet (500mm L x
300mm D) connected with fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau
or equivalent. Handles: Arch Handles(1nos. for each shutter) 128 mm pitch made of
Zinc alloy diy cast handle with satin finish. Dustbin Holder- 1nos. 250mm(+/-5%) dia
3mm thk SS wire mounted on hinged door . SS sink not included. (Actual dimensions
may vary upto +/-5% as per site measurements).

7 Nos
2.2 Single shutter plain shelf unit (600w X 540d X 690h)mm

Page 4 of 15
 Supply, installation & placement of Kitchen single shutter plain shelf unit. Cabinet
Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with balancing
matte Ral white laminate finish inside (Body panels) and The carcase of floor units
will be supported by 100mm H vertical ajustable legs upto 20 mm which will be
covered with PVC skirting in brushed aluminium finish attached by hardware of
skirting . Unit Construction: Floor units will be made using Prelaminated BWR plywood
panels connected with fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau or
equivalent. Shutters: 18mm thk. Marine ply of grade IS- 710. Finish on shutter
surface: 1mm thk. decorative laminate finish both side with 2mm(+/- 0.1) thk. edge
banding of Rehau or equivalent. Shelves: 18mm thk both side laminated Prelaminated
BWR grade (IS - 303) shelf inside of the cabinet (600mm L x 540mm D) connected
with fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent.
Hinges: Auto hinge of Hettich or equivalent with CED coating for extended corrosion
resistance. Opening angle of hinge : 95° for door thickness of 15mm-22mm provided
with mounting plates, with 35mm cup diameter. Each shutter should be connected
with the carcase with 2nos of hinges. Skirting : Rehau make PVC Co-extruded
skirting attached with shutters. (Height: 100mm). Handles: Handles: Arch
Handles(1nos. for each shutter) 128 mm pitch made of Zinc alloy diy cast handle with
satin finish.(Actual dimensions may vary upto +/-5% as per site measurements)

7 Nos
2.3 Double shutter plain shelf unit (800w X 540d X 690h)mm
Supply, installation & placement of Kitchen double shutter plain shelf unit. Cabinet
Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with balancing
matte Ral white laminate finish inside (Body panels) and The carcase of floor units
will be supported by 100mm H vertical ajustable legs upto 20 mm which will be
covered with PVC skirting in brushed aluminium finish attached by hardware of
skirting . Unit Construction: Floor units will be made using Prelaminated BWR plywood
panels connected with fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau or
equivalent. Shutters: 18mm thk. Marine ply of grade IS- 710. Finish on shutter
surface: 1mm thk. decorative laminate finish both side with 2mm(+/- 0.1) thk. edge
banding of Rehau or equivalent. Shelves: 18mm thk both side laminated Prelaminated
BWR grade (IS - 303) shelf inside of the cabinet (600mm L x 540mm D) connected
with fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent.
Hinges: Auto hinge of Hettich or equivalent with CED coating for extended corrosion
resistance. Opening angle of hinge : 95° for door thickness of 15mm-22mm provided
with mounting plates, with 35mm cup diameter. Each shutter should be connected
with the carcase with 2nos of hinges. Skirting : Rehau make PVC Co-extruded
skirting attached with shutters. (Height: 100mm). Handles: Handles: Arch
Handles(1nos. for each shutter) 128 mm pitch made of Zinc alloy diy cast handle with
satin finish.(Actual dimensions may vary upto +/-5% as per site measurements)

14 Nos
2.4 Double Gas cylinder corner cabinet (450+ 400w X 540d X 690h)mm

Page 5 of 15
 Supply, installation & placement of Kitchen (double capacity) Gas cylinder cabinet .
Cabinet Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with
balancing matte Ral white laminate finish inside for top & side panels (Body panels).
Unit Construction: Floor units will be made using Prelaminated BWR plywood panels
with 1 mm. thk. decorative laminate finish connected with fasteners with 1.2mm(+/-
0.1) thk. edge banding of Rehau or equivalent. Shutters: 18mm thk. Marine ply of
grade (IS- 710) made byfold shutters. Finish on shutter surface: 1mm thk. decorative
laminate finish both side with 2mm(+/- 0.1) thk. edge banding of Rehau or
equivalent. Hinges: Auto hinge of Hettich or equivalent with CED coating for
extended corrosion resistance. Opening angle of hinge : 165° for door thickness of
15mm-22mm provided with mounting plates, with 35mm cup diameter for byfold
shutters. Each shutter should be connected with the carcase with 2nos of hinges.
Skirting : Rehau make PVC Co-extruded skirting attached with shutters. (Height:
100mm). Handles: Handles: Arch Handles(1nos. for entire unit) 128 mm pitch made
of Zinc alloy diy cast handle with satin finish. Gas trolley- 2nos. 280mm(+/-5%) dia
3mm thk SS wire trolley with 4nos ABS castors for 2 nos cylinder storage . (Actual
dimensions may vary upto +/-5% as per site measurements)

7 Nos
2.5 Three drawer dish unit (600w X 540d X 690h)mm
Supply, installation & placement of Kitchen three drawer dish unit . Cabinet Material:
18mm thk. Prelaminated BWR (IS-303) plywood panels with balancing matte Ral white
laminate finish inside (Body panels) and the carcase of floor units will be supported by
100mm (H) vertical ajustable legs upto 20 mm which will be covered with PVC skirting in
brushed aluminium finish attached by hardware of skirting . Unit Construction: Floor
units will be made using Prelaminated BWR plywood (Grade IS-303) panels with 1 mm.
thk. decorative laminate finish connected with fasteners with 1.2mm(+/- 0.1) thk. edge
banding of Rehau or equivalent. Drawer size: Drawer 1 (600mmL x 520mmD x 100mmH)
with Prelaminated BWR plywood (Grade IS-303) inside structure with cutlery organiser,
Drawer 2: (600mmL x 520mmD x 100mmH) with SS wire basket for cup/ bowls upto
100mm high, Drawer 3:(600mmL x 520mmD x 250mmH)with wire basket for Plates /
Dish placement. Drawer with cuttlery tray: The cabinet will be consisting of SS-304
Grade i/c Cutlery Basket +Cup & Saucer 100 mm + Thali Bskt 150 mm with 600m width
, and fittings required SS screw for fixing above quadro slide of hettich or eq . Finish on
drawer front fascia : 1mm thk. decorative laminate finish both side on 18mm thk. Marine
ply of grade (IS-710) with 2mm(+/- 0.1) thk edge banding of Rehau or eq. Overall
dimensions of drawer front: Drawer 1: (600mmL x 520mmD x 162.5mmH), Drawer 2:
(600mmL x 520mmD x 162.5mmH), Drawer 3 (600mmL x 520mmD x 325mmH). Ball
slide Telescopic Drawer Channel: Manufactured from CRCA steel for longevity. Black
Powder Coated for extended corrosion resistance made of Hettich or equivalent .Black
Powder Coated for better corrosion resistance. Colour: Black. Finish: Type Glossy.
Weight Limit: 45 Kilograms. Length- 300mm. Skirting : Rehau make PVC Co-extruded
skirting. (Height: 100mm). Handles: Arch Handles(1nos. for each drawer) 128 mm pitch
made of Zinc alloy diy cast handle with satin finish. (Actual dimensions may vary upto +/-
5% as per site measurements).

7 Nos
2.6 Bottle pull out (300w X 540d X 690h)mm

Page 6 of 15
 Supply, installation & placement of under counter bottle pull out . Cabinet Material:
18mm thk. Prelaminated BWR (IS-303) plywood panels with balancing matte Ral
white laminate finish inside (Body panels) and The carcase of floor units will be
supported by 100mm H vertical ajustable legs upto 20 mm which will be covered with
PVC skirting in brushed aluminium finish attached by hardware of skirting . Unit
Construction: Carcase will be made using Prelaminated BWR plywood (Grade IS-303)
panels with 1mm. thk decorative laminate connected with fasteners with 1.2mm(+/-
0.1) thk. edge banding of Rehau or equivalent. Drawer pull out: The bottle pullout
consist of 2 nos. Solid Metal Base Baskets ( box for bottle storage in two different
levels) made of MS powder coated CRCA 0.8mm. sheet and fittings required SS screw
for fixing above quadro slide of hettich or eq . Finish on drawer front fascia : 18mm
thk. MPly with 1mm thk. decorative laminate finish both side with 2mm(+/- 0.1) thk.
edge banding of Rehau or equivalent. Ball slide Telescopic Drawer
Channel:Manufactured from CRCA steel for longevity. Black Powder Coated for
extended corrosion resistance made of Hettich or equivalent .Black Powder Coated for
better corrosion resistance.
Colour: Black. Finish: Type Glossy. Weight Limit: 45 Kilograms. Length- 300mm.
Skirting : Rehau make PVC Co-extruded skirting. (Height: 100mm). Handles: Arch
Handles(1nos. for each drawer) 128 mm pitch made of Zinc alloy diy cast handle with
satin finish. (Actual dimensions may vary upto +/-5% as per site measurements)

7 Nos
Overhead Wall Unit
2.7 Overhead double shutter plain shelf unit (1000w X 310d X 600h)mm

Supply, installation & placement of Kitchen overhead plain shelf unit with M ply
shutter. Cabinet Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with
balancing matte Ral white laminate finish inside (Body panels). Unit Construction:
overhead units will be made using Prelaminated BWR plywood panels with 1 mm. thk.
decorative laminate finish connected with fasteners with 1.2mm(+/- 0.1) thk. edge
banding of Rehau or equivalent. Shutters: 18mm thk. Marine ply of grade IS- 710.
Finish on shutter surface: 1mm thk. decorative laminate finish both side with 2mm(+/-
0.1) thk. edge banding of Rehau or equivalent. Shelves:The cabinet will be consisting
of adjustable shelves that shall be supported on approved quality SS pins and shall be
adjustable for different heights as per requirement. 18mm thk both side laminated
Prelaminated BWR grade (IS - 303) shelf inside of the cabinet connected with
fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Hinges:
Auto hinge of Hettich or equivalent with CED coating for extended corrosion
resistance. Opening angle of hinge : 95° for door thickness of 15mm-22mm provided
with mounting plates, with 35mm cup diameter. Each shutter should be connected
with the carcase with 2nos of hinges. Handles: Arch Handles(1nos. for each shutter)
128 mm pitch made of Zinc alloy diy cast handle with satin finish. The unit shall be
fixed to the wall using metal screws of appropriate size and rawl plugs. (Actual
dimensions may vary upto +/-5% as per site measurements)

14 Nos

TYPE- VI KITCHEN

Page 7 of 15
3.0 Providing, Supplying, installation & furnishing of factory made combination of linear
& L shape moduflex kitchen from manufacturers certified with ISO 9001:2015, ISO
50001:2018, ISO45001:2018, ISO 14001:2015 (all ISO must be from NABCB/IAF
accredited agency), BIFMA (LEVEL 2), IAQ, IGBC PLlatinum, Indoor Air Advantage
Gold, Greenguard (by UL), Griha 2019. as per approved drawing and design/
specification of Engineer In-Charge. Overall dimensions of undercounter deck 1 :
(1300+2685) (L) X 560 (D) X 690 (H) mm., undercounter deck 2 : 2000 (L) X 560
(D) X 690 (H) mm., undercounter deck 3 : 2750 (L) X 560 (D) X 690 (H) mm., 1 nos.
of partly glazed Overhead cabinet: 2750 (L) X 310 (D) X 600 (H) mm. , 2 nos. of
partly glazed Overhead cabinet: 900 (L) X 310 (D) X 600 (H) mm. (with soft closing
hinges & channels)
Not in Scope: Chimney ,Sink & accessories, water filtration, Premoulded & prepolished
granite top kitchen counter, Flooring , painting, wall tiles, power and gas connections
& other civil, plumbing & electrical works.

1 each 4,39,095 4,39,095

Base Cabinets
3.1 Single shutter Floor Sink unit (600w X 540d X 690h)mm
Supply, installation & placement of Kitchen Floor sink unit. Cabinet Material: 18mm
thk. Prelaminated BWR (IS-303) plywood panels with balancing matte Ral white
laminate finish inside (Body panels) and the carcase of floor units will be supported
by 100mm H vertical ajustable legs upto 20 mm which will be covered with PVC
skirting in brushed aluminium finish attached by hardware of skirting .Unit
Construction: Floor units will be made using Prelaminated BWR plywood (Grade IS-
303) panels with 1 mm. thk. decorative laminate finish connected with fasteners with
1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Shutters: 18mm thk.
prelaminated Marine ply of grade (IS- 710). Finish on shutter surface: 1mm thk.
decorative laminate finish both side with 2mm(+/- 0.1) thk. edge banding of Rehau or
equivalent. Hinges: Soft closing Auto hinge of Hettich or equivalent with CED coating
for extended corrosion resistance. Opening angle of hinge : 95° for door thickness of
15mm-22mm provided with mounting plates, with 35mm cup diameter. Each shutter
should be connected with the carcase with 2nos of hinges. Skirting : Rehau make
PVC Co-extruded skirting attached with the carcase.(Height: 100mm). Handles: Arch
Handles(1nos. for each shutter) 128 mm pitch made of Zinc alloy diy cast handle with
satin finish. Dustbin Holder- 1nos. 250mm(+/-5%) dia 3mm thk SS wire mounted on
hinged door . SS sink not included. (Actual dimensions may vary upto +/-5% as per
site measurements).

1 Nos
3.2 Single shutter plain shelf unit (500w X 540d X 690h)mm

Page 8 of 15
 Supply, installation & placement of Kitchen single shutter plain shelf unit. Cabinet
Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with balancing
matte Ral white laminate finish inside (Body panels) and The carcase of floor units
will be supported by 100mm H vertical ajustable legs upto 20 mm which will be
covered with PVC skirting in brushed aluminium finish attached by hardware of
skirting . Unit Construction: Floor units will be made using Prelaminated BWR plywood
(Grade IS-303) panels with 1 mm. thk. decorative laminate finish connected with
fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Shutters:
18mm thk. Marine ply of grade IS- 710. Finish on shutter surface: 1mm thk.
decorative laminate finish both side with 2mm(+/- 0.1) thk. edge banding of Rehau or
equivalent. Shelves: 18mm thk both side laminated Prelaminated BWR grade (IS -
303) shelf inside of the cabinet (600mm L x 540mm D) connected with fasteners with
1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Hinges: Soft closing Auto
hinge of Hettich or equivalent with CED coating for extended corrosion resistance.
Opening angle of hinge : 95° for door thickness of 15mm-22mm provided with
mounting plates, with 35mm cup diameter. Each shutter should be connected with
the carcase with 2nos of hinges. Skirting : Rehau make PVC Co-extruded skirting
attached with shutters. (Height: 100mm). Handles: Handles: Arch Handles(1nos. for
each shutter) 128 mm pitch made of Zinc alloy diy cast handle with satin
finish.(Actual dimensions may vary upto +/-5% as per site measurements)

1 Nos
3.3 Double Gas cylinder corner cabinet (270+ 440w X 540d X 690h)mm
Supply, installation & placement of Kitchen (double capacity) Gas cylinder cabinet .
Cabinet Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with
balancing matte Ral white laminate finish inside for top & side panels (Body panels).
Unit Construction: Floor units will be made using Prelaminated BWR plywood panels
with 1 mm. thk. decorative laminate finish connected with fasteners with 1.2mm(+/-
0.1) thk. edge banding of Rehau or equivalent. Shutters: 18mm thk. Marine ply of
grade (IS- 710) made shutters. Finish on shutter surface: 1mm thk. decorative
laminate finish both side with 2mm(+/- 0.1) thk. edge banding of Rehau or
equivalent. Hinges: Soft closing Auto hinge of Hettich or equivalent with CED coating
for extended corrosion resistance. Opening angle of hinge : 95° for door thickness of
15mm-22mm provided with mounting plates, with 35mm cup diameter for byfold
shutters. Each shutter should be connected with the carcase with 2nos of hinges.
Skirting : Rehau make PVC Co-extruded skirting attached with shutters. (Height:
100mm). Handles: Handles: Arch Handles(1nos. for each shutter) 128 mm pitch
made of Zinc alloy diy cast handle with satin finish. Gas trolley- 2nos. 280mm(+/-5%)
dia 3mm thk SS wire trolley with 4nos ABS castors for 2 nos cylinder storage . (Actual
dimensions may vary upto +/-5% as per site measurements)

1 Nos
3.4 Bottle pull out (300w X 540d X 690h)mm

Page 9 of 15
 Supply, installation & placement of under counter bottle pull out . Cabinet Material:
18mm thk. Prelaminated BWR (IS-303) plywood panels with balancing matte Ral
white laminate finish inside (Body panels) and The carcase of floor units will be
supported by 100mm H vertical ajustable legs upto 20 mm which will be covered with
PVC skirting in brushed aluminium finish attached by hardware of skirting . Unit
Construction: Carcase will be made using Prelaminated BWR plywood (Grade IS-303)
panels with 1mm. thk decorative laminate connected with fasteners with 1.2mm(+/-
0.1) thk. edge banding of Rehau or equivalent. Drawer pull out: The bottle pullout
consist of 2 nos. Solid Metal Base Baskets ( box for bottle storage in two different
levels) made of MS powder coated CRCA 0.8mm. sheet and fittings required SS screw
for fixing above quadro slide of hettich or eq . Finish on drawer front fascia : 18mm
thk. MPly with 1mm thk. decorative laminate finish both side with 2mm(+/- 0.1) thk.
edge banding of Rehau or equivalent. Soft closing Ball slide Telescopic Drawer
Channel: Manufactured from steel for longevity, Special Anti-Rebound Function. Zinc
plated for better corrosion resistance. Colour silver. Finish Type-Glossy.Weight Limit-
35 Kilograms.Length- 300mm. Skirting : Rehau make PVC Co-extruded
skirting.(Height: 100mm). Handles: Arch Handles(1nos. for each unit) 128 mm pitch
made of Zinc alloy diy cast handle with satin finish. (Actual dimensions may vary upto
+/-5% as per site measurements)

1 Nos
3.5 Three drawer dish unit (600w X 540d X 690h)mm
Supply, installation & placement of Kitchen three drawer dish unit . Cabinet Material:
18mm thk. Prelaminated BWR (IS-303) plywood panels with balancing matte Ral
white laminate finish inside (Body panels) and the carcase of floor units will be
supported by 100mm (H) vertical ajustable legs upto 20 mm which will be covered
with PVC skirting in brushed aluminium finish attached by hardware of skirting . Unit
Construction: Floor units will be made using Prelaminated BWR plywood (Grade IS-
303) panels with 1 mm. thk. decorative laminate finish connected with fasteners with
1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Drawer size: Drawer 1
(600mmL x 520mmD x 100mmH) with Prelaminated BWR plywood (Grade IS-303)
inside structure with cutlery organiser, Drawer 2: (600mmL x 520mmD x 100mmH)
with SS wire basket for cup/ bowls upto 100mm high, Drawer 3:(600mmL x 520mmD
x 250mmH)with wire basket for Plates / Dish placement. Drawer with cuttlery tray:
The cabinet will be consisting of SS-304 Grade i/c Cutlery Basket +Cup & Saucer 100
mm + Thali Bskt 150 mm with 600m width , and fittings required SS screw for fixing
above quadro slide of hettich or eq . Finish on drawer front fascia : 1mm thk.
decorative laminate finish both side on 18mm thk. Marine ply of grade (IS-710) with
2mm(+/- 0.1) thk edge banding of Rehau or eq. Overall dimensions of drawer front:
Drawer 1: (600mmL x 520mmD x 162.5mmH), Drawer 2: (600mmL x 520mmD x
162.5mmH), Drawer 3 (600mmL x 520mmD x 325mmH). Soft closing Ball slide
Telescopic Drawer Channel:Manufactured from steel for longevity, Special Anti-
Rebound Function. Zinc plated for better corrosion resistance. Colour silver
Finish Type-Glossy.Weight Limit-35 Kilograms.Length- 300mm. Skirting : Rehau make
PVC Co-extruded skirting. (Height: 100mm). Handles: Arch Handles(1nos. for each
drawer) 128 mm pitch made of Zinc alloy diy cast handle with satin finish. (Actual
dimensions may vary upto +/-5% as per site measurements).

1 Nos
3.6 Double shutter plain shelf unit (900w X 540d X 690h)mm

Page 10 of 15
 Supply, installation & placement of Kitchen double shutter plain shelf unit. Cabinet
Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with balancing
matte Ral white laminate finish inside (Body panels) and The carcase of floor units
will be supported by 100mm H vertical ajustable legs upto 20 mm which will be
covered with PVC skirting in brushed aluminium finish attached by hardware of
skirting . Unit Construction: Floor units will be made using Prelaminated BWR plywood
(Grade IS-303) panels with 1 mm. thk. decorative laminate finish connected with
fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Shutters:
18mm thk. Marine ply of grade IS- 710. Finish on shutter surface: 1mm thk.
decorative laminate finish both side with 2mm(+/- 0.1) thk. edge banding of Rehau or
equivalent. Shelves: 18mm thk both side laminated Prelaminated BWR grade (IS -
303) shelf inside of the cabinet (600mm L x 540mm D) connected with fasteners with
1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Hinges: Soft closing Auto
hinge of Hettich or equivalent with CED coating for extended corrosion resistance.
Opening angle of hinge : 95° for door thickness of 15mm-22mm provided with
mounting plates, with 35mm cup diameter. Each shutter should be connected with
the carcase with 2nos of hinges. Skirting : Rehau make PVC Co-extruded skirting
attached with shutters. (Height: 100mm). Handles: Handles: Arch Handles(1nos. for
each shutter) 128 mm pitch made of Zinc alloy diy cast handle with satin
finish.(Actual dimensions may vary upto +/-5% as per site measurements)

2 Nos
3.7 Single shutter plain shelf unit (450w X 540d X 690h)mm
Supply, installation & placement of Kitchen single shutter plain shelf unit. Cabinet
Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with balancing
matte Ral white laminate finish inside (Body panels) and The carcase of floor units
will be supported by 100mm H vertical ajustable legs upto 20 mm which will be
covered with PVC skirting in brushed aluminium finish attached by hardware of
skirting . Unit Construction: Floor units will be made using Prelaminated BWR plywood
(Grade IS-303) panels with 1 mm. thk. decorative laminate finish connected with
fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Shutters:
18mm thk. Marine ply of grade IS- 710. Finish on shutter surface: 1mm thk.
decorative laminate finish both side with 2mm(+/- 0.1) thk. edge banding of Rehau or
equivalent. Shelves: 18mm thk both side laminated Prelaminated BWR grade (IS -
303) shelf inside of the cabinet (600mm L x 540mm D) connected with fasteners with
1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Hinges: Soft closing Auto
hinge of Hettich or equivalent with CED coating for extended corrosion resistance.
Opening angle of hinge : 95° for door thickness of 15mm-22mm provided with
mounting plates, with 35mm cup diameter. Each shutter should be connected with
the carcase with 2nos of hinges. Skirting : Rehau make PVC Co-extruded skirting
attached with shutters. (Height: 100mm). Handles: Handles: Arch Handles(1nos. for
each shutter) 128 mm pitch made of Zinc alloy diy cast handle with satin
finish.(Actual dimensions may vary upto +/-5% as per site measurements)

1 Nos
3.8 Single shutter plain shelf unit (500w X 540d X 690h)mm

Page 11 of 15
 Supply, installation & placement of Kitchen single shutter plain shelf unit. Cabinet
Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with balancing
matte Ral white laminate finish inside (Body panels) and The carcase of floor units
will be supported by 100mm H vertical ajustable legs upto 20 mm which will be
covered with PVC skirting in brushed aluminium finish attached by hardware of
skirting . Unit Construction: Floor units will be made using Prelaminated BWR plywood
panels connected with fasteners with 1mm(+/- 0.1) thk. edge banding of Rehau or
equivalent. Shutters: 18mm thk. Marine ply of grade IS- 710. Finish on shutter
surface: 1mm thk. decorative laminate finish both side with 2mm(+/- 0.1) thk. edge
banding of Rehau or equivalent. Hinges: Soft closing hinges of Hettich or equivalent
with CED coating for extended corrosion resistance. Skirting : Rehau make PVC Co-
extruded skirting. (Height: 100mm). Handles: Arch Handles 128 mm pitch made of
SS-304. (Actual dimensions may vary upto +/-5% as per site measurements)

1 Nos
3.9 2 Drawer Tranquil unit (900w X 540d X 690h)mm
Supply, installation & placement of Kitchen 2 drawer tranquil unit. 18mm thk.
Prelaminated BWR (IS-303) plywood panels with balancing matte Ral white laminate
finish inside (Body panels) and The carcase of floor units will be supported by 100mm
H vertical ajustable legs upto 20 mm which will be covered with PVC skirting in
brushed aluminium finish attached by hardware of skirting . Unit Construction: Floor
units will be made using Prelaminated BWR plywood panels connected with fasteners
with 1mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Drawer Panels:Bottom
& back will be made using Prelaminated BWR plywood panels connected with
fasteners with 1mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Side panels
will be made MS powder coated CRCA 0.8mm. sheet. Ball slide Telescopic Drawer
Channel:Manufactured from steel for longevity, Special Anti-Rebound Function. Zinc
plated for better corrosion resistance. Colour silver. Finish Type-Glossy.Weight Limit-
35 Kilograms.Length- 300mm. Finish on drawer front fascia : 18mm thk. MPly with
1mm thk. decorative laminate finish both side with 2mm(+/- 0.1) thk. edge banding
of Rehau or equivalent. Skirting : Rehau make PVC Co-extruded skirting in metallic
silver and black color (Height: 100mm /150mm) . Handles: Arch Handles 128 mm
pitch made of SS-304.

1 Nos
3.10 Double shutter plain shelf unit (1000w X 540d X 690h)mm
Supply, installation & placement of Kitchen double shutter plain shelf unit. Cabinet
Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with balancing
matte Ral white laminate finish inside (Body panels) and The carcase of floor units
will be supported by 100mm H vertical ajustable legs upto 20 mm which will be
covered with PVC skirting in brushed aluminium finish attached by hardware of
skirting . Unit Construction: Floor units will be made using Prelaminated BWR plywood
(Grade IS-303) panels with 1 mm. thk. decorative laminate finish connected with
fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Shutters:
18mm thk. Marine ply of grade IS- 710. Finish on shutter surface: 1mm thk.
decorative laminate finish both side with 2mm(+/- 0.1) thk. edge banding of Rehau or
equivalent. Shelves: 18mm thk both side laminated Prelaminated BWR grade (IS -
303) shelf inside of the cabinet (600mm L x 540mm D) connected with fasteners with
1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Hinges: Soft closing Auto
hinge of Hettich or equivalent with CED coating for extended corrosion resistance.
Opening angle of hinge : 95° for door thickness of 15mm-22mm provided with
mounting plates, with 35mm cup diameter. Each shutter should be connected with
the carcase with 2nos of hinges. Skirting : Rehau make PVC Co-extruded skirting
attached with shutters. (Height: 100mm). Handles: Handles: Arch Handles(1nos. for
each shutter) 128 mm pitch made of Zinc alloy diy cast handle with satin
finish.(Actual dimensions may vary upto +/-5% as per site measurements)

2 Nos
Overhead Wall Unit
3.11 Overhead single shutter plain shelf unit (450w X 310d X 600h)mm

Page 12 of 15
 Supply, installation & placement of Kitchen overhead plain shelf unit with M ply
shutter. Cabinet Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with
balancing matte Ral white laminate finish inside (Body panels). Unit Construction:
overhead units will be made using Prelaminated BWR plywood panels with 1 mm. thk.
decorative laminate finish connected with fasteners with 1.2mm(+/- 0.1) thk. edge
banding of Rehau or equivalent. Shutters: 18mm thk. Marine ply of grade IS- 710.
Finish on shutter surface: 1mm thk. decorative laminate finish both side with 2mm(+/-
0.1) thk. edge banding of Rehau or equivalent. Shelves:The cabinet will be consisting
of adjustable shelves that shall be supported on approved quality SS pins and shall be
adjustable for different heights as per requirement. 18mm thk both side laminated
Prelaminated BWR grade (IS - 303) shelf inside of the cabinet connected with
fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Hinges:
Soft closing Auto hinge of Hettich or equivalent with CED coating for extended
corrosion resistance. Opening angle of hinge : 95° for door thickness of 15mm-22mm
provided with mounting plates, with 35mm cup diameter. Each shutter should be
connected with the carcase with 2nos of hinges. Handles: Arch Handles(1nos. for
each shutter) 128 mm pitch made of Zinc alloy diy cast handle with satin finish. The
unit shall be fixed to the wall using metal screws of appropriate size and rawl plugs.
(Actual dimensions may vary upto +/-5% as per site measurements)

3 Nos
3.12 Overhead Glass single shutter plain shelf unit (450w X 310d X 600h)mm

Supply, installation & placement of Kitchen overhead plain shelf unit with frosted
glass shutter. Cabinet Material: 18mm thk. Prelaminated BWR (IS-303) plywood
panels with balancing matte Ral white laminate finish inside (Body panels). Unit
Construction: overhead units will be made using Prelaminated BWR plywood panels
connected with fasteners with 1mm(+/- 0.1) thk. edge banding of Rehau or
equivalent. Shutters: 4mm thk. frosted glass shutter fitted in Aluminium Profile of
overall size 500 mm W x 600 mm H. Openable Shutters shall have Aluminium Framed
Glass fixed to the cabinet using Soft closing hinges. Shelves: The cabinet will be
consisting of adjustable shelves that shall be supported on approved quality SS pins
and shall be adjustable for different heights as per requirement. Hinges: Soft closing
Auto hinge of Hettich or equivalent with CED coating for extended corrosion
resistance. Opening angle of hinge : 95° for door thickness of 15mm-22mm provided
with mounting plates, with 35mm cup diameter. Each shutter should be connected
with the carcase with 2nos of hinges. Handles: Arch Handles(1nos. for each shutter)
128 mm pitch made of Zinc alloy diy cast handle with satin finish. The unit shall be
fixed to the wall using metal screws of appropriate size and rawl plugs. (Actual
dimensions may vary upto +/-5% as per site measurements)

2 Nos
3.13 Overhead Glass double shutter plain shelf unit (900w X 310d X 600h)mm

Page 13 of 15
 Supply, installation & placement of Kitchen overhead plain shelf unit with frosted
glass shutter. Cabinet Material: 18mm thk. Prelaminated BWR (IS-303) plywood
panels with balancing matte Ral white laminate finish inside (Body panels). Unit
Construction: overhead units will be made using Prelaminated BWR plywood panels
connected with fasteners with 1mm(+/- 0.1) thk. edge banding of Rehau or
equivalent. Shutters: 4mm thk. frosted glass shutter fitted in Aluminium Profile of
overall size 500 mm W x 600 mm H. Openable Shutters shall have Aluminium Framed
Glass fixed to the cabinet using Soft closing hinges. Shelves: The cabinet will be
consisting of adjustable shelves that shall be supported on approved quality SS pins
and shall be adjustable for different heights as per requirement. Hinges: Soft closing
Auto hinge of Hettich or equivalent with CED coating for extended corrosion
resistance. Opening angle of hinge : 95° for door thickness of 15mm-22mm provided
with mounting plates, with 35mm cup diameter. Each shutter should be connected
with the carcase with 2nos of hinges. Handles: Arch Handles(1nos. for each shutter)
128 mm pitch made of Zinc alloy diy cast handle with satin finish. The unit shall be
fixed to the wall using metal screws of appropriate size and rawl plugs. (Actual
dimensions may vary upto +/-5% as per site measurements)

1 Nos
3.14 Overhead double shutter plain shelf unit (900w X 310d X 600h)mm
Supply, installation & placement of Kitchen overhead plain shelf unit with M ply
shutter. Cabinet Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with
balancing matte Ral white laminate finish inside (Body panels). Unit Construction:
overhead units will be made using Prelaminated BWR plywood panels with 1 mm. thk.
decorative laminate finish connected with fasteners with 1.2mm(+/- 0.1) thk. edge
banding of Rehau or equivalent. Shutters: 18mm thk. Marine ply of grade IS- 710.
Finish on shutter surface: 1mm thk. decorative laminate finish both side with 2mm(+/-
0.1) thk. edge banding of Rehau or equivalent. Shelves:The cabinet will be consisting
of adjustable shelves that shall be supported on approved quality SS pins and shall be
adjustable for different heights as per requirement. 18mm thk both side laminated
Prelaminated BWR grade (IS - 303) shelf inside of the cabinet connected with
fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Hinges:
Soft closing Auto hinge of Hettich or equivalent with CED coating for extended
corrosion resistance. Opening angle of hinge : 95° for door thickness of 15mm-22mm
provided with mounting plates, with 35mm cup diameter. Each shutter should be
connected with the carcase with 2nos of hinges. Handles: Arch Handles(1nos. for
each shutter) 128 mm pitch made of Zinc alloy diy cast handle with satin finish. The
unit shall be fixed to the wall using metal screws of appropriate size and rawl plugs.
(Actual dimensions may vary upto +/-5% as per site measurements)

1 Nos
3.15 Overhead single shutter plain shelf unit (500w X 310d X 600h)mm

Page 14 of 15
 Supply, installation & placement of Kitchen overhead plain shelf unit with M ply
shutter. Cabinet Material: 18mm thk. Prelaminated BWR (IS-303) plywood panels with
balancing matte Ral white laminate finish inside (Body panels). Unit Construction:
overhead units will be made using Prelaminated BWR plywood panels with 1 mm. thk.
decorative laminate finish connected with fasteners with 1.2mm(+/- 0.1) thk. edge
banding of Rehau or equivalent. Shutters: 18mm thk. Marine ply of grade IS- 710.
Finish on shutter surface: 1mm thk. decorative laminate finish both side with 2mm(+/-
0.1) thk. edge banding of Rehau or equivalent. Shelves:The cabinet will be consisting
of adjustable shelves that shall be supported on approved quality SS pins and shall be
adjustable for different heights as per requirement. 18mm thk both side laminated
Prelaminated BWR grade (IS - 303) shelf inside of the cabinet connected with
fasteners with 1.2mm(+/- 0.1) thk. edge banding of Rehau or equivalent. Hinges:
Soft closing Auto hinge of Hettich or equivalent with CED coating for extended
corrosion resistance. Opening angle of hinge : 95° for door thickness of 15mm-22mm
provided with mounting plates, with 35mm cup diameter. Each shutter should be
connected with the carcase with 2nos of hinges. Handles: Arch Handles(1nos. for
each shutter) 128 mm pitch made of Zinc alloy diy cast handle with satin finish. The
unit shall be fixed to the wall using metal screws of appropriate size and rawl plugs.
(Actual dimensions may vary upto +/-5% as per site measurements)

1 Nos
4 Supply, Installation and placement of modular storage from manufacturers certified
with ISO 9001:2015, ISO 50001:2018, ISO45001:2018, ISO 14001:2015 (all ISO must
be from NABCB/IAF accredited agency), BIFMA (LEVEL 2), Indoor air quality, Indoor
Air Advantage Gold, Greenguard (by UL), Griha 2019. Main Unit: 900(W) x 450(D) x
2325(H), Addon Unit: 450(W) x 450(D) x 2325(H) (Height including leveler). Height
of leveler is 50mm and adjustment possible is 15mm. Construction & Materiel:
Aesthetically appealing completely knock down construction. The add on units are
stock widthwise to form a row of storage. (Note: Single Main unit should not be
offered. Minimum 1 Main + 1Addon to be offered Legs fitted with screw type
leveler. Made from combination of Top panel (0.5mm CRCA), side panel (0.5mm
CRCA), Bottom panel (0.5mm CRCA for 450W/600W and 0.8mm CRCA for 900W,
Back panel (0.5mm CRCA), Top Bottom stiffener (1.2mm CRCA) and End Cover
(0.5mm CRCA). —CRCA ’D’ Grade as per IS—513. Shelving : • It is a 12 bend
panel made of 0.7mm Thick CRCA (D Grade, IS—513). • Each shelf has max Load
Capacity of —80kg UDL for 1200W unit 55kg UDL for 900W unit 40kg UDL for
600W unit 30kg UDL for 450W unit.• 5 Nos. of fixed shelves for 2325(H). Shutter:
Construction & Material: •Glass Door is made from the combination of aluminium
alloy (63400) extrusion and clear glass. •Metal Door is made from 0.6mm
thick CRCA (D Grade, IS—513) • Soft closing Hinge. Handle: • Asthetically
appealing handle mode of Aluminium.

1 Set 1,20,616 1,02,217

Lock: • Cam Lock: 3 Way locking provision. Click action mechanism. Key removable
in locked and unlocked positions. Zinc alloy die cast housing. Finish: • Epoxy
Polyester Powder coated to the thickness of 50 microns (+/—10 micron). Overall
Dimensions: 2700mm (w) x 450mm (d) x 2325mm (h). Combination : 1nos. 900 wide
main unit with combination shutter + 900mm wide addon unit with combination
shutter + 2nos. 450mm wide open shelf addon unit.

Total 36,45,942 (A)

Add GST on "A"18% 6,56,270
Total 43,02,212
SAY 43,02,212

ASSISTANT EXECUTIVE
ASSISTANT ENGINEER (P), KOL-III EXECUTIVE ENGINEER
ENGINEER
CPWD, KOLKATA-64 EE-KOL-III, CPWD, KOL-64 EE-KOL-III, CPWD, KOL-64

Page 15 of 15