Winneshiek

STRUCTURAL ABREVIATIONS STRUCTURAL SYMBOLS STRUCTURAL NOTES Expansion and

Renovation
STRUCTURAL NOTES
These notes are provided for typical conditions. See plans and details for specific DESIGN LOADS CONCRETE REINFORCING GENERAL STRUCTURAL STEEL
ADDN'L Additional DIMENSIONAL LUMBER Provide standard hooks where hook lengths are not specified. Structural steel fabrication and construction shall conform to the AISC "Manual of
@ At requirements in other areas.
& And Roof loads See sheet S4.00 for required reinforcing splice lengths. Steel Construction" and the AISC "Code of Standard Practice for Steel Buildings and 901 Montgomery St
ANCH Anchor DEFERRED STRUCTURAL SUBMITTALS Roof Dead Loads: min=15 psf, max=25psf superimposed. Provide epoxy coated reinforcing for all concrete exposed to weather or soil, such as Bridges".
AB Anchor Bolt WOOD BLOCKING Deferred submittals are those portions of the design which are not submitted at the time Roof Snow Loads Parameters: retaining walls, exterior walls, exterior piers, exterior columns, foundation and exterior Galvanize structural steel exposed to weather and brick support angles in exterior Decorah, IA 52101
L Angle of permit application but are to be submitted to the building official prior to installation. Ground snow (Pg) 35 psf beams, slab on void forms, and paving. Epoxy coated reinforcing is not required for walls according to ASTM A123.
ALT Alternate building foundation walls unless specifically noted. Do not field cut or alter structural members without approval of the Structural
Deferred submittals are governed by Iowa Code (2022) chapter 542B. The following Exposure factor (Ce): 1
ARCH
BSMT
Architect or Architectural
Basement FINISH WOOD items are to be issued as deferred submittals: Occupancy Importance factor (Is) Support slab reinforcing for its entire length and independent of beam steel. Engineer. 216051
BM Beam Buildings A&B: Is=1; Risk Category II
BRG
BNT
Bearing
Bent STEEL OR METAL
Temporary shoring for existing structure
Underpinning
Building H: Is=1 .2; Risk Category IV
Thermal factor (Ct): 1
Soft metric bar sizes vs. inch-pound (U.S. System of Measures) bar size table. These
drawings reflect the U.S. System of Measure.
LATERAL LOAD RESISTING SYSTEM FOR STRUCTURAL STEEL BUILDINGS
The following elements comprise the primary lateral load resisting system:
Winneshiek Medical
BTWN or BET Between
BLK Block Temporary earth retention systems
Steel connections
Snow Drift Loads: In accordance with ASCE 7-16 Chapter 7
Roof live load (Lr): 20 psf with allowance for reduction Inch-Pound Bar Size Soft Metric Bar Size
Roof Diaphragm: Steel roof decking.
Floor Diaphragm: Composite steel deck and concrete.
Center
BB Bond Beam / Lintel Beam
BOT or BTM Bottom CONCRETE BLOCK - HOLLOW OR SOLID Steel joists: special joists, and bridging Designation Designation Collector elements/drag struts: Steel beams, steel joists, drag struts, and Decorah, IA 52101
Brkt Bracket Cold-formed steel framing Floor Live Loads #3 -------------------------------------- #10 reinforcing in concrete slabs.
Bldg Building Curtainwall systems Mechanical room: 125 psf + 10 psf for ceilings #4 -------------------------------------- #13 Lateral load resisting system: Steel bracing, Concrete walls.
Cant Cantilever Office areas: 50 psf + 35 psf for ceilings and partitions #5 -------------------------------------- #16
FACE OR COMMON BRICK Steel stairs and landings
CLG Ceiling #6 -------------------------------------- #19 STRUCTURAL STEEL CONNECTIONS
CTR Center Stairs 100 psf
CTR'D Centered For all deferred structural submittals, include design and calculations prepared and Public Areas and lobbies: 100 psf + 35 psf ceilings and partitions #7 -------------------------------------- #22 Typically, provide welded or bolted shop connections and bolted field connections.

IA CL
C
CLR
COL
Center Line
Channel
Clear
Column
RIGID INSULATION
certified by an engineer licensed to practice in the state in which the project is located as
part of the submittal documents. See specification (structural notes) for additional shop
drawing requirements. Provide deferred submittals a minimum of 30 days prior to
installation, and after contractor's review, to the architect (structural engineer) for review
Light Storage 125 psf + 10 psf for ceilings
Patients rooms: 40 psf + 35 psf for ceilings and partitions
Upper Level Corridors 80 psf + 35 psf ceilings and partitions
Operating rooms and laboratories: 60psf + 35psf for ceilings and partitions
#8 -------------------------------------- #25
#9 -------------------------------------- #29
#10 ------------------------------------ #32
#11 ------------------------------------ #36
Typical bolts are 3/4" Ø A325-N bolts in standard or short slotted holes.
Provide shear connections according to the standard connection schedules on
sheet S4.00 and as follows:
Use double angles for all girders and for all beams W24 and larger.
COMP Composite BATT OR BLANKET INSULATION #14 ------------------------------------ #43
CONC Concrete for general conformance to the contract documents. After architect's (structural Double angle connection or single plate connection may be used for other
CMU Concrete Masonry Unit engineer's) review, submit to building official for review and approval. Do not install Seismic Loads #18 ------------------------------------ #57 beams.
COND Condition deferred submittal items until submittal documents have been reviewed and approved ASCE 7-16 Equivalent Lateral Force Procedure For skewed girder connections, use a single plate connection with a
CONN Connection PLYWOOD by the building official. Importance factor CONCRETE COVER ON REINFORCING capacity equal to or greater than the double angle connection for that beam
CONST Construction Buildings A&B: Ie = 1; Risk Category II Footings: 3" clear bottom and sides size.
CJ Control Joint 2" clear top Beams that connect to a column or wall on either end and support the load
CONT Continuous Refer to architectural, civil, mechanical, and electrical drawings for additional deferred Building H: Ie = 1.5; Risk Category IV
CONTR Contractor EARTH, FILL OR BACKFILL submittal components. Site Soil Classification: C Walls: 1-1/2" clear outside face and surfaces exposed to from another beam are considered girders. Transfer beams support
DBA Deformed Bar Anchor Ss = 0.053g, S1 = 0.042g earth or weather (2” for #6 bars or larger) columns are considered girders.
DL Dead Load EXISTING CONDITIONS Sds = 0.046g, Sd1 = 0.042g 3/4" clear inside face Beams requiring a non-typical connection will be noted on the drawings as
DEFL Deflection
SAND OR GROUT Verify all dimensions, elevations, and detail of existing structure where they affect this Seismic design Category A Columns, Piers, and Beams: 1-1/2" clear to ties or stirrups DA-X for double angle connections or SP-X for single plate connections
DTL or DET Detail Slab on Grade: Place reinforcing in upper third of slab (where X denotes the number of bolt rows in the connection).
DIA Diameter construction. Design Base shear (V)
DIAG Diagonal Notify engineer if there are any deviations from the contract documents. Buildings A&B (minimum 3/4" clear top) Design bracing, moment, and other connections not detailed on the drawings for the
DIM Dimension Obtain prior approval from Structural Engineer before cutting openings or recesses or V = 28.4 Kips Topping Slab & Concrete: Place reinforcing in upper third of slab loads indicated. Submit calculations for these connections.
CONCRETE Slab on Metal Deck: (minimum 3/4" clear top)
DWL(s) Dowel(s) making other modifications to existing structure not shown on structural drawings. Seismic Response Coefficient (Cs) = .015
DWG(s) or DRWG Drawing(s) Response Modification Factor (R) = 3, Both directions STEEL JOISTS AND BRIDGING
EA Each Basic Seismic-Force-Resisting-System: FOUNDATIONS Design steel joists in accordance with AISC and SJI Standard Specifications.
EF Each Face COORDINATION - ARCHITECTURAL, MECHANICAL AND ELECTRICAL ITEMS
STONE H. STEEL SYSTEMS NOT SPECIFICALLY For wall footings, provide 32 bar dia. lap at reinforcing splices and full crossing lap at Fabricate in accordance with AISC Specification.
EW Each Way Verify all depressions, dimensions, elevations, openings, equipment supports, and
E-W East - West details and coordinate by reference to architectural, mechanical and electrical DETAILED FOR SEISMIC RESISTANCE, EXCLUDING intersections. Bridging shall conform to SJI Specifications.
E East drawings. At non-bearing masonry walls shown on architectural drawings, brace top of CANTILEVER COLUMN SYSTEMS (both directions) Unless otherwise noted, center wall footings under walls and column footings under Weld "K" series joists to beams and bearing plates with two ⅛" fillet welds 2" long.
Fe Effective Force (P.T.)
EXISTING CONCRETE STRUCTURE columns. Positively anchor all bridging to walls and beams parallel to joists.
wall to structure, see arch. Building H:
ELEC Electrical V = 0.017*W (Kips) Footing elevations shown on plan are to top of footing (TOF). Provide horizontal bridging in last joist space. See detail 1/S3.06 for anchorage of
EL Elevation Hook wall and column dowels at 3" clear bottom of footing. bridging to steel beams.
ELEV Elevator BP1 BEARING PLATE MARK - SEE SCHEDULE OPENINGS Seismic Response Coefficient (Cs) = 0.017
EQ Equal Verify size and location of all openings with architectural, mechanical and electrical Response Modification Factor (R) = 4, Both directions Supplier shall design joist headers to support 100% of joist reaction for supported
EXP Expansion drawings. Structural drawings do not necessarily show all openings. Basic Seismic-Force-Resisting-System: CONCRETE SLABS ON GRADE joist capacity at given span or reaction from special joist designed by supplier.
EJ or EXP JT Expansion Joint SC1 COLUMN MARK - SEE SCHEDULE Ordinary Reinforced Concrete Shear Walls, and Steel Provide thickened slab below non-bearing masonry walls. See detail 3/S3.02 . Supplier shall incorporate joist header reaction on adjacent joists as an add-load and
Place openings in floor and roof not shown on structural drawings between structural
EXT Extend or Exterior Systems at Penthouse Roof Not Specifically Detailed for See details 1/S3.02 to 2/S3.02 for control/construction joints. coordinate panel points or design for bend-check.
FF Far Face
members. Notify Structural Engineer before openings larger than 12" in any dimension
are added. Seismic Resistance. If control joints are not shown on plan, place control/construction joints at columns and See details 11/S3.06 for reinforcing at concentrated loads (piping, mech rooftop
FV Field Verify EP1 EMBED PLATE MARK - SEE SCHEDULE provide additional joints to meet the spacings indicated below: equip curbs, etc.) at joists.
FLG Flange Obtain prior approval from Structural Engineer before making any openings through
FLR Floor structural members if the openings are not shown on the structural drawings. Wind loads: Exterior slabs, 10'-0" oc maximum Typical joist top and bottom chords to be designed for a 100-lb bend-check load
FT Foot Design code: ASCE 7-16 Interior slabs, 12'-0" oc maximum anywhere along span.
FTG Footing F1 FOOTING MARK - SEE SCHEDULE Exposure B "L" shaped panels and rectangular panels (with length to width ratio greater than 1.5)
DESIGN CODES AND STANDARDS
FOUND or FDN Foundation Buildings A&B are not allowed. COMPOSITE STEEL DECK SLABS
GALV Galvanized International Building Code (IBC) 2015 – As amended by the Iowa State Building
Code 2020 Basic wind Speed: 107 mph (3 seconds gust) All control/construction joints must be continuous and not staggered or offset. See Sheet S3.03 for typical composite details.
GA Gauge
KEY NOTES - SPECIFIC NOTES KEYED TO American Society of Civil Engineers (ASCE) 7-16 – Minimum Design Loads and Risk Category II See detail 6/S4.00 for deck fastening.
GC General Contractor 1
GL or GLU-LAM Glue Laminated Wood AN ELEMENT OR AREA, SEE SCHEDULE Associated Criteria for Buildings and Other Structures Building H COLD-FORMED STEEL FRAMING Weld composite steel deck to supports with 5/8" dia. puddle welds at 12" oc. Screw
H H Shaped Column International Code Council (ICC) 500-14 – ICC/NSSA Standard for the Design and Basic wind Speed: 120 mph (3 seconds gust) Design and construct cold-formed steel framing according to AISI Specification for side laps at 36" max oc. with #10 TEK screws. Weld side margins to supports with
HP High Point Risk Category IV Design of Cold-formed Steel Structural Members. Gravity and lateral loads shall be 3/8”x 1-1/2” seam welds at 36” max. oc. Deck flutes and ribs must line up from one
HS Headed Stud(s)
Construction of Storm Shelters
L1 LINTEL MARK - SEE SCHEDULE American Concrete Institute (ACI) 318-19 – Building Code Requirements for Structural according to IBC Chapter 16. Provide calculations, prepared and certified by an span of deck to the next.
HSS Hollow Structural Shape
HK Hook Concrete TEMPORARY BRACING engineer licensed to practice in the state in which the project is located, and detailed Do not cut openings in deck until concrete has reached its design strength. Provide
HORIZ Horizontal American Institute of Steel Construction 360-16 – Specification for Structural Steel This structure is a non-self-supporting steel frame that requires interaction with slabs, shop drawings for review. 2-#5 @ 12" located on each side of openings up to 2'-6" wide perpendicular to deck
IN Inch PIER MARK - SEE SCHEDULE Buildings (AISC 360) steel deck, and concrete walls to provide the required lateral stability. The drawings are intended to express the minimum design performance. Alternate span.
P1
INFO Information
American Institute of Steel Construction – Steel Construction Manual– Fifteenth Provide required temporary bracing for structural steel until permanent bracing, slabs, design of equivalent capacity will be considered if compatible with architectural Locate bars parallel to deck span ¾"clear from the bottom of flute and extend to C 2022 Quetica Professional Engineers, Inc.
ID Inside Diameter steel deck, and walls are in place. requirements and if calculations and detailed shop drawings are submitted for review. support purlins. Locate perpendicular bars ¾" clear from the top of deck and extend All rights reserved.
IF Inside Face Edition (AISC 15th) This document is an instrument of service and is the property of
American Welding Society D1.1-2015 – Structural Welding Code – Steel and Provide temporary bracing for all walls (concrete, masonry, cold formed steel, or wood) The cold formed steel framing system supports the weight of lightweight (non-brick) 1'-6" past edge of opening. For openings wider than 2'-6", provide steel frame per Quetica Professional Engineers, Inc. and may not be used or copied
INSUL Insulation PC1 PILE CAP MARK - SEE SCHEDULE
INT Interior D1.3-2008 – Structural Welding Code –Sheet Steel as modified by AISC Specifications until they are of adequate design strength and are properly anchored in final form. exterior materials, resists lateral loads, and provides lateral stability for exterior detail 19/S3.04 . Weld deck to angle frames at 12" oc. Multiple smaller openings without prior written consent.
JT Joint Steel Joist Institute (SJI) 100-2015 – Standard Specification for K-Series. materials. Provide connections that transfer loads to the primary structural frame and spaced less than 2'-0" on center shall be treated as one large opening.
JST(s) Joist(s) Steel Deck Institute RD-2017 – Standard for Steel Roof Deck (SDI RD) GEOTECHNICAL INFORMATION allow for a minimum deflection of floor and roof framing of L/360. Pour composite slabs to a constant thickness.
K Kips REVISION MARK - INDICATES A CHANGE The designations for cold-formed steel follow the recommendations of the Steel
KIP 1 Kip = 1,000 lbs 1 Steel Deck Institute C-2017 – Standard for Composite Steel Floor Deck – Slabs (SDI
AFTER CONTRACT DOCUMENT ISSUE C) The foundation design is based on the recommendations contained in the Geotechnical Framing Alliance and are as follows: STEEL ROOF DECK
K/FT Kips per Foot
KSF Kips per Square Foot American Iron and Steel Institute (AISI) S100-16 – North American Specification for the Report prepared by 'Terracon Consultants, Inc.' dated August 30, 2022. xxxDyyy-zzz (e.g. 600S162-33) See detail 6/S4.00 for deck fastening.
KSI Kips per Square Inch SHEAR WALL MARK - SEE SCHEDULE Design of Cold-Formed Steel Structural Members Allowable foundation pressures are to be verified in field by a licensed professional xxx = Member depth in 1/100 inches (e.g. 600 = 6") Provide steel frame at openings wider than 6", including, but not limited to, roof
LW Light Weight
SW1 D = Member type designator as follows: drains, mechanical duct work, and piping. See details 8/S3.06 . Weld deck to angle
geotechnical engineer.
LTL Lintel Foundation design parameters are as follows: S = Stud or joist section with flange stiffeners (Cee shapes) frames at 12" oc.
LL Live Load
DESIGN STRESSES
STUD RAIL MARK - SEE SCHEDULE Reinforcing Steel (Fy) • Maximum net allowable bearing pressure: 5000 psf Buildings A&B, 3000 psf Building T = Track section Allowable point loads applied to steel deck are controlled by the following:
LLH Long Leg Horizontal SR1
LLV Long Leg Vertical 60,000 psi (A615, A706, Grade 60) H. U = Cold rolled channel or channel studs without flange stiffeners Maximum of 250 pounds in any 5’-0”x5’-0” square area.
LP Low Point Concrete (f'c) (28 day compressive strength) • Estimated modulus of subgrade reaction: 125 psi/in. F = Furring channels Maximum of 100 pounds on any individual hanger location.
LSH Long Side Horizontal 5,000 psi for exterior concrete • Soil moist unit weight: 125 pcf. yyy = flange width in 1/100 inches (e.g. 162 = 1 5/8") The total mechanical load applied to a deck-supporting member shall not exceed 5
LSL Laminated Strand Lumber P1 WALL REINFORCING MARK - SEE SCHEDULE 4,000 psi unless noted • Lateral passive pressure with equivalent fluid pressure (Ultimate): zzz = minimum base metal thickness in mils (e.g. 33 = 0.033") pounds per square foot uniform load (typical) or 25 pounds per square foot in
LSV Long Side Vertical Fine-grained backfill: 285 pcf Provide members based on material thickness. The following table of approximate mechanical rooms.
LVL Laminated Veneer Lumber 4,000 psi for interior slab on grade
MFG Manufacturer / Manufacturing 4,000 psi for normal weight concrete slabs on steel deck Granular backfill: 360 pcf equivalent gages is provided for reference only.
MAS Masonry 3,500 psi for footings and topping • Coefficient of friction (ultimate): MINIMUM THICKNESS (IN) APPROXIMATE STEEL GAGE
MO Masonry Opening ELEVATION CHANGE Structural Steel (Fy) ≥2 ft of compacted granular fill: 0.40 0.033 20
MAT Material 50,000 psi (A992 or A572 Grade 50) for W shapes Bedrock: 0.45 0.043 18
MAX Maximum Refer to the Earthwork Specifications, Civil and Architectural design for 0.054 16
MECH Mechanical
36,000 psi (A36) for bars, plates, angles channels and other shapes
50,000 psi (A500, Grade C) for rectangular structural tubing recommendations for site preparation/soil correction. Spread footing excavations to be 0.068 14
MBR Member
MEZZ Mezzanine Electrode for welding (Fuxx) nearly vertical, concrete placed neat against excavations vertical faces, unless properly 0.097 12
BRACED FRAME fill against vertical face of footing is provided, see Geotechnical report. 0.118 10
MIN Minimum 70,000 psi (E-7018)
MISC Miscellaneous Use minimum 18-gage studs for walls with veneer anchors. Use minimum 14-gage
MC Miscellaneous Channel BACKFILLING studs if anchors are welded to studs.
M Moment
Backfill and materials behind foundation and retaining walls shall be as outlined in the
MPH Miles per Hour
A GRID BUBBLE Earthwork Specifications.
NF Near Face
N North Do not backfill or compact earth against walls retaining earth until supporting slabs have
N-S North - South reached 75% of their design strength or adequate bracing is in place. Provide bracing
NOM Nominal designed and certified by an Engineer licensed in the state in which the project is
NTS Not To Scale SECTION NUMBER
X located. Submit design and calculations to Structural Engineer for review only.
NO or # Number
OC On Center
XXX Backfill evenly on both sides of foundation walls to prevent overturning or lateral wall
OPNG or OPG Opening
DRAWING NUMBER WHERE movement.
OPP Opposite SECTION IS FOUND
OD Outside Diameter
OF Outside Face
/ Per DETAIL NUMBER
PCF Pounds per Cubic Foot X
PLK Plank XXX
PL Plate
DETAIL NUMBER WHERE
PT Post Tension(ing) DETAIL IS FOUND
# Pound
PSF Pound per Square Foot
PSI Pound per Square Inch ELEVATION NUMBER
PSL Parallel Strand Lumber X
PC Precast XXX
RFG Reinforcing DRAWING NUMBER WHERE
REINF Reinforcing or Reinforce ELEVATION IS FOUND
REBAR Reinforcing Bar
REQ'D Required
REV Reverse
RD Roof Drain
MATCH LINE
SCHED or SCH
SEC
Schedule
Section
SHEET INDEX REQUIRED STRUCTURAL SPECIAL INSPECTIONS
V Shear EXISTING BUILDING LINE
SHT Sheet
SIM Similar
SOG Slab on Grade
IN ADDITION TO THE REGULAR INSPECTIONS, THE FOLLOWING STRUCTURAL ITEMS REQUIRE SPECIAL NSPECTION IN
S South HIDDEN EXISTING BUILDING LINE S0.00 TITLE SHEET, STRUCTURAL NOTES ACCORDANCE WITH SECTION 1704 OF THE INTERNATIONAL BUILDING CODE. SEE SPECIFICATION SECTION 014533
SPS Spaces S2.00a FOOTING AND FOUNDATION PLAN - AREA 'A' AND MATERIAL SPECIFICATION SECTIONS FOR SPECIFIC REQUIREMENTS. CONSTRUCTION NOT ASSOCIATED WITH I hereby certify that this plan, specifcation or report was
SPEC Specification
S2.00b FOOTING AND FOUNDATION PLAN - AREA 'B' THE STRUCTURAL SYSTEM MAY REQUIRE SPECIAL INSPECTION BUT IS NOT LISTED HERE. prepared by me or under my direct supervision and that I
SQ Square
BREAK LINE S2.00h FOOTING AND FOUNDATION PLAN - AREA 'H' am a duly Licsened Professional Engineer under the laws
STAGG Stagger
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

STD Standard
ITEM REQUIRED SPECIFICAL REMARKS of the state of Minnesota.
S2.01a MAIN LEVEL FLOOR FRAMING PLAN - AREA - 'A' INPECTION
STL Steel
STRUCT or STR Structure S2.01b MAIN LEVEL FLOOR FRAMING PLAN - AREA - 'B'
DIRECTION OF SLOPE 1. Soils compliance prior to YES Reference IBC 1705.6
SUPP Support S2.01h MAIN LEVEL FLOOR FRAMING PLAN - AREA 'H'
TEMP Temporary or Temperature foundation construction Katherine Russell
S2.02a LOW ROOF & PENTHOUSE FLOOR FRAMING PLAN AREA 'A' & 'B'
THRU Through
S2.02h LOW ROOF & PENTHOUSE FLOOR FRAMING PLAN AREA 'H' Date 12/30/2022 Lic. No. P27101
T&B Top and Bottom STEEL BEAM SPLICE
TOB Top of Beam
2. Cast in place YES Reference IBC table 1705.8, 1704.8, 1704.10
S2.03a PENTHOUSE ROOF FRAMING PLAN - AREA 'A' & 'B' deep foundation elements
TOF Top of Footing
TOS Top of Slab S2.03h PENTHOUSE ROOF FRAMING PLAN - AREA 'H' Revisions
TYP Typical STEEL BEAM CONTINUOUS S3.00 SECTIONS AND DETAILS Description Date Num
UN Unless Noted OVER SUPPORT 3. Grade beams YES Reference IBC table 1705.3, ACI 318
S3.01 SECTIONS AND DETAILS
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

UNO Unless Noted Otherwise sec. 26.13.3.2

VER Verify S3.02 SECTIONS AND DETAILS
VERT Vertical ◀ MOMENT CONNECTION FOR
S3.03 SECTIONS AND DETAILS 4. Structural concrete YES Reference IBC table 1705.3, ACI 318
VIF Verify in Field STEEL BEAMS
WWF Welded Wire Fabric S3.04 SECTIONS AND DETAILS sec. 26.13.3.2
W West or Wide Flange S3.05 SECTIONS AND DETAILS
WND Window ✱ LOCATION OF BEAM BRACE S3.06 SECTIONS AND DETAILS 5. Reinforcing steel YES Reference IBC table 1705.3, ACI 318
W/ With
W/O Without S3.07 SECTIONS AND DETAILS sec. 26.13.3.2
WD Wood S3.08 SECTIONS AND DETAILS
CJP Complete Joint Penetration Weld SPAN OF STRUCTURAL ELEMENT 6. Bolts installed in concrete YES Reference IBC table 1705.3
S3.09 SECTIONS AND DETAILS
S4.00 SCHEDULES, SECTIONS AND DETAILS 7. Expansion/adhesive YES Reference IBC table 1705.3, ACI 318
anchors sec. 26.13.3.2
28/12/2022 10:51:15

REINFORCING STEEL SPAN

8. Structural steel fabrication YES Reference IBC table 1705.2, AISC 360 - 16, Comm: 216050
chapter N
DIMENSION LINES Date: 12/30/2022
9. Structural welding YES Reference IBC table 1705.2, AISC 360 chapter N Drawn:
Check: North
MATERIAL LIMIT LINES 10. High strength bolting YES Reference IBC table 1705.2, AISC 360 chapter N

11. Open web steel joist and NO Reference IBC table 1705.2
MATERIAL NOT INCLUDED
IN LIMIT LINES girders TITLE SHEET,
S FOOTING STEP STRUCTURAL
S NOTES

Scale: 1/8" = 1'-0"

PERMIT SET
NOT FOR CONSTRUCTION S0.00
 E.4 D.99 D.57 D.2 B.65 B.9 INDICATES
FOOTING MARK
Winneshiek
Expansion and

85 F3
2'-0" 11'-4" 9'-9 1/4" 13'-8 3/4" 11'-6 1/4" 17'-0"

6"
Renovation

'-
S3.00

AREA A

AREA B
3
E.6 INDICATES

TYP.
TOP
TOF 85'-0" 901 Montgomery St
3'-0" 3'-0"
F3 -6" 3'-0" 3'-0" F3 -6" 1 3'-0" 3'-0" F3 -6" OF FOOTING
2'-0" 2'-0" ' ' S3.07 '
85 85 85 Decorah, IA 52101

2'-2"
6'-3 1/4" TOF 85'-0"

1'-8"
5'-3" 1'-0 1/4" WF1
WF1
P1-A P1-A P1-A 216051

3'-0"

3'-0"

3'-0"
1'-8"

1'-2"

1'-2"
2'-0"
5.0 Winneshiek Medical

5 7/8"
P1-B
SC2
Center

5 7/8"
2'-0"
1'-1"

TYP.
3'-0"

3'-0"

3'-0"
SC2 7 SC3
FOUNDATION BEAM SC3 7 Decorah, IA 52101

S3.00

S3.01
32 3/8" x 38"

11
F1 -6"

4
'
85

10'-0"
FOUNDATION LEGEND
IA
8'-11"
6
S3.02
TYP.
3
17'-8"

S3.02
WALL FOUNDATION SCHEDULE

19'-1"
DIMENSIONS WALL REINFORCEMENT FOUNDATION REINFORCEMENT
7" 7"
MARK REMARKS
4

1'-8"
S3.00 STARTERS
B H T VERT REINF HORIZ REINF TRANV REINF LONG REINF
TOF 85'-0" BARS
0 0 WF1 2'-2" 1'-0" 1'-2" #4@8" OC. #4@8" OC. #4@8" OC. (3)#4 #4@8" OC.
F1 '-7" F1 '-7"
ADDITIONAL REINF,
86

WF1
F1 -6" 86
' SEE DETAIL 8/S3.00,
WF2 2'-5" 1'-0" 1'-5 1/4" #4@8" OC. #4@8" OC. #4@8" OC. (3)#4 #4@8" OC.
85 SEE PLAN FOR
LOCATION

3'-0"

3'-0"
P8 SC8 SC14 WF4 3'-2" 1'-0" 1'- 2 1/2" #4@8" OC. #4@8" OC. #4@8" OC. (3)#4 #4@8" OC.

2'-0"

2'-0"
WF5 3'-2" 1'-0" 1'- 2 1/2" #4@8" OC. #4@8" OC. #4@8" OC. (3)#4 #4@8" OC.
4.0 UNLESS NOTED OTHERWISE:
- SEE DETAIL 4/S3.00
SC7
2'-0"

2'-0"

3'-0"
SC8 SC8

3'-0"
TYP.
2
S3.00

F1 -5"
'
2'-0" 2'-0" PIER SCHEDULE CONC. f'c = 4000 PSI
86
1'-1" 2'-11"
TOF 85'-0" 0 3'-0" 3'-0"
F1 '-7" 3'-0" 3'-0" REINFORCING
86 MARK SIZE VERTICAL TIES HOOKS N (*) REMARKS
P1-A 2'-0" x 2'-8 1/2" (20)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
2'-2"
P1-B 2'-0" x 2'-8 1/2" (20)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
WF1

P2 2'-8" x 2'-8 1/2" (24)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
P3 2'-8" x 2'-0" (20)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
P4 2'-0" x 2'-0" (12)#6 #3@10" OC. 3@1 1/2" OC.
4
P5 3'-0" x 2'-0" (18)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
S3.00 P6 2'-8" x 3'-0 1/4" x 2'-10 1/4" (21)#7 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
P7 2'-9" x 3'-1 1/4" x 2'-10 3/4" (21)#7 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
TOF 84'-0"
P8 2'-6 1/2" x 2'-0" (16)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
S
24'-11"

P9 2'-0" x 2'-0" (12)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
TOF 83'-0" P10 2'-0" x 2'-0" (12)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
4" CONCRETE SLAB-ON-GRADE
S

UNLESS NOTED OTHERWISE:

7" 7"
- SEE DETAILS 1/S3.00
- PIERS TOP OF SURACE ELEVATION (TOS) 87'-6" C 2022 Quetica Professional Engineers, Inc.
TOF 82'-0" - FOR ANCHOR BOLTS SEE DETAIL 1/S4.00 All rights reserved.
S

3'-6" This document is an instrument of service and is the property of

3'-6" Quetica Professional Engineers, Inc. and may not be used or copied
without prior written consent.
S3.00

TYP.
F8 -6"
6

_______
13
' CONC. f'c = 3500 PSI
S3.00 82
COLUMN FOOTING SCHEDULE ALLOWABLE SOIL STRESS
5'-11 1/4"

F5 -0" F5 -0" BEARING: SEE S0.00

1'-2 1/2" ' '
87 87
WF1
REINFORCING
2'-1"

F1 -8"
8"
1'-2"

5'-6 1/2"

' MARK SIZE DEPTH SHORT-WAY LONG-WAY REMARKS

83
1'-4"

F1 4'-0"x4'-0" 1'-6" (7)#5 HOOK (7)#5 HOOK

3.1

4'-0"

4'-0"
SC3
3'-2 1/4"

F2 18'-0"x10'-0" 2'-1" (15)#6 (27)#6 TOP AND BOTTOM

SC15
8"

P5 P4
2'-0"

F3 6'-0"x6'-0" 1'-6" (10)#5 (10)#5 TOP AND BOTTOM

P6
F4 14'-0"x4'-0" 2'-1" (7)#5 (21)#5 HOOK
3.0
5'-0 3/4"

S3.00

F5 8'-0"x8'-0" 2'-1" (13)#6 (13)#6 TOP AND BOTTOM

12

SC3
2'-0"

SC12 SC13 F6 14'-0"x6'-0" 2'-1" (9)#6 HOOK (21)#5 TOP AND BOTTOM
9'-2"

12

4'-0"

4'-0"
S3.00 8" 8'-2" 8" 1'-3 3/4"
F7 9'-0"x4'-0" 2'-1" (7)#6 (14)#5 HOOK
W F1

2'-0" 2'-0" F8 15'-0"x13'-0" 1'-6" (20)#5 (24)#5 TOP AND BOTTOM

TOF 82'-0"
F9 9'-0"x9'-0" 1'-6" (14)#5 (14)#5 TOP AND BOTTOM
7'-5 1/2"

1
F1 '-6" F10 6'-0"x6'-0" 1'-8" (10)#5 (10)#5
82 5 TOF 82'-6" 7 F11 11'-0"x7'-0" 1'-6" (11)#5 (17)#5 TOP AND BOTTOM
S3.07 S3.00 4'-0" 4'-0" 4'-0" 4'-0"
_______ F12 18'-0"x8'-0" 2'-1" (13)#6 (27)#5 TOP AND BOTTOM
S

11
S3.00 F13 9'-0"x9'-0" 2'-11" (14)#6 (14)#6 TOP AND BOTTOM
8"

1'-6" DEEP SUMP PIT.

TOF 83'-2" SEE SECTION 6/S3.00 F14 3'-6"x6'-0" 1'-6" (6)#5 (10)#5
15'-5"

& 7/S3.00 , SEE ARCH & F15 8'-0"x8'-0" 1'-10" (7)#7 (7)#7 BOTTOM
S

4 15'-0" MECH DRAWINGS FOR F16 6'-0"x6'-0" 1'-6" (8)#5 (8)#5 BOTTOM
S3.00 LOCATION AND SIZE
3 F17 20'-0"x9'-0" 2'-6" (9)#7 (12)#8 TOP AND BOTTOM
7
F1 '-1" F18 9'-0"x9'-0" 2'-0" (8)#7 (8)#7 BOTTOM
F9 8"
S3.07
85
1'-2" '- F19 10'-0"x10'-0" 2'-2" (10)#7 (10)#7 TOP AND BOTTOM
83
23'-3"

F20 12'-0"x13'-0" 2'-6" (12)#8 (12)#8 TOP AND BOTTOM

S3.00

F21 12'-0"x12'-0" 2'-6" (10)#8 (10)#8 TOP AND BOTTOM

S3.00
83

12
°

12
4
4'-6"

S3.00 F22 9'-0"x4'-0" 2'-1" (7)#6 (10)#7 TOP AND BOTTOM

4'-6"

SEE DRAWING 2/S3.00 AND 3/S3.00 U.N.O.

P7 SC6 HOOK: TYPICAL HOOK REQUIRED ON BOTH SIDES AB
SC3

2.3 CD
1'-4"

2'-2"

1'-2"
4'-6"

2'-6 1/4" 3'-0" 2'-6" 2'-6 1/4" 1'-6" 1'-6 1/4" 2'-6"
KEYNOTES E F
4'-6"

F5 -5"
1'-6 1/4" WF1 '
86
7'-10"

TOF 83'-2"
7 AESS 3 STEEL, SEE SCHEDULE SHEET S4.00 AND SPECIFICATIONS. G H
4'-6"
4'-6" 4'-6" 4'-6"
4'-0"

4'-0"
8 SC11
2'-0"
SC14 SC10
TOF 85'-0" S3.00
WF2

11 1/2"
2.0 KEY PLAN
TYP.
2'-0"

FOOTING AND FOUNDATION PLAN - AREA 'A'

3'-1 1/4"

_______
10 5
S3.00 S3.00 1 1/4" = 1'-0"
4'-0"

4'-0"
1'-5 1/4" 1 1/4"
I hereby certify that this plan, specifcation or report was
E.6 2'-0" 2'-0" 0 prepared by me or under my direct supervision and that I
F1 -5" am a duly Licsened Professional Engineer under the laws
9"

FOUNDATION BEAM

'
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

86 of the state of Minnesota.

1.07
23" x 31"

F5 -5" 4'-0 1/4" 4'-0" 4'-0" 4'-0"

UNLESS NOTED OTHERWISE:
'
86 1. SEE STRUCTURAL NOTES SHEET S0.00 FOR MORE INFORMATION.
FOUNDATION BEAM

Katherine Russell
EXISTING. BLDG. TOF 85'-0" 2. SEE ARCHITECTURAL DRAWINGS FOR LOCATIONS OF RAMPS, SLAB SLOPES, STEPPED SLABS AND PARTITION

FOUNDATION BEAM
WALLS. Date 12/30/2022 Lic. No. P27101
36" x 38"

3. REFER TO ARCHITECTURAL DRAWINGS FOR ADDITIONAL INFORMATION AND DIMENSIONS.

EXISTING. BLDG. TOF 85'-0" 4. PROVIDE 4" SLAB ON GRADE REINFORCE WITH MICRO FIBERS AT 1.5 POUNDS PER CUBIC YARD. REFER TO

36" x 38"
Revisions
3/4" 11 1/2" ARCHITECTURAL AND CIVIL DESIGN FOR GRANULAR BASE MATERIAL UNDER SLAB ON GRADE. SEE DETAIL 1/S3.02
Description Date Num
5. SEE SLAB ON GRADE DETAILS IN DRAWING S3.00.
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

11 1/2" 6. PROVIDE VAPER BARRIER DIRECTLY BELOW SLAB ON GRADE INSIDE.

21'-4"

9
S3.00 7. TOP OF GROUND SLAB ELEVATION (TOS) - TYP. 88'-0", SEE ARCH FOR SPECIAL SLOPED AREAS.
EXISTING. BLDG. TOP OF WALL 90'-6 5/8"
23'-5"

TYP. TYP. 8. GRADE BEAMS:

5 5 a. SEE TOP OF BEAMS ON SECTIONS.
S3.00 S3.00
S3.00

2 1/4" b. SEE SECTIONS FOR GEOMETRY AND REINFORCEMENT.

5

EXISTING. BLDG. TOF 85'-0" 4'-6" 4'-6" LAP REINFORCING AS FOLLOWS:

F7 -5"
F7 -5"

8'-9 3/4" 4'-6" 4'-6"

86
86

FOUNDATION BEAM BAR N° OTHER TOP

'
'
TYP.

36" x 38" #4: 24" 30"

#5: 28" 38"
6"

#6: 34" 44"

GRADE BEAM REINFORCEMENT MUST NOT BE INTERRUPTED IN PIERS OR FOUNDATIONS.
3'-0"

4'-0"

4'-0"

4'-0"

9. WALL FOUNDATION:
28/12/2022 10:51:18

11 3/4" 7 3/4" a. TYP. TOP OF WALL = 88'-0", TYP. BOTTOM OF WALL SEE SECTIONS ON PLANS.
FOUNDATION BEAM b. SEE SECTIONS FOR GEOMETRY AND REINFORCEMENT DETAILS.
Comm: 216050
c. WALL AND FOUNDATION REINFORCEMENT MUST NOT BE INTERRUPTED IN PIERS AND FOUNDATIONS.
6"

36" x 23"
3 Date: 12/30/2022
S3.01 10. WALL FOUNDATION REINFORCEMENT MUST NOT BE INTERRUPTED AT FOOTINGS OR PIERS, REINFORCEMENT TO BE
Drawn:
F7 -5"
86

SC5 ANCHORED AND LAPPED PROPERLY.

4'-7 1/2"

4'-7 1/2"

4'-7 1/2"
'

11. SEE THIS SHEET AND SHEET S4.00 FOR SCHEDULES. Check: North
1.112
1'-6 1/2"
1'-6 1/2"

12. INDICATES COLUMN BLOCKOUT SECOND STAGE CONCRETE.

8"

SC1 SC4 13. COORDINATE WITH ARCHITECTURE DESIGN EXISTING GROUND SLAB CONNECTION; SEE 4/S3.02 AND 5/S3.02
8"

8"

1.0 FOOTING AND

2'-4"
9 7/8"

FOUNDATION
2'-1"

2.07
S S3.01 X.1 PLAN - AREA 'A'
S3.02

EXISTING BLDG. TOS

S3.02

EXISTING. BLDG. TOF 85'-8"

4
4

11 1/2" 88' 5 3/8"

EXISTING. BLDG. TOF 85'-4"
S3.01
S3.01

EXISTING. BLDG. TOF 85'-4"

2
1

EXISTING. BLDG. TOF 85'-8"

EXISTING. BLDG. TOF 85'-8"

E.7.07 F.07 X.E X.D X.C Scale: As indicated

PERMIT SET
NOT FOR CONSTRUCTION S2.00a
 Winneshiek
INDICATES
FOOTING MARK
Expansion and
B.9 A.9 A.4 A.1 1.91
29'-4" 20'-0 1/4" 6'-6 3/4" 8'-8"
Renovation

85 F3
6"
'-
901 Montgomery St
INDICATES
Decorah, IA 52101

S3.00
AREA A

AREA B
4'-8" 8'-8" 4'-8 1/4" TOP

3
OF FOOTING

TYP.
216051

85 F3

85 F3
"

"
'-6

'-6
Winneshiek Medical

2'-2"
TOF 85'-0" TOF 85'-0"

2'-2"
Center

5'-0"
WF1 WF1
P1-A P1-A P1-A P2

3'-0"

3'-0"
Decorah, IA 52101

1'-2"
5.0

5 7/8"
SC3 SC2 SC3 SC3

3'-0"

3'-0"
IA

S3.00

S3.00

5'-0"
4

4
3'-0" 3'-0" 3'-0" 3'-0" FOUNDATION LEGEND

12 5
S3.01

F2 -1"
S3.00

86
TYP.

'
11
S3.01 WALL FOUNDATION SCHEDULE

FOUNDATION BEAM

FOUNDATION BEAM

17'-8"
TYP.
2
S3.07 DIMENSIONS WALL REINFORCEMENT FOUNDATION REINFORCEMENT

24" x 38"

32" x 38"
3 MARK REMARKS
S3.07 STARTERS
B H T VERT REINF HORIZ REINF TRANV REINF LONG REINF
2'-8" BARS
1'-7 1/4" WF1 2'-2" 1'-0" 1'-2" #4@8" OC. #4@8" OC. #4@8" OC. (3)#4 #4@8" OC.
ADDITIONAL REINF,

F1 '-6"
86 10

86 10

85
"

"
SEE DETAIL 8/S3.00,

'-7

'-7
F

S3.01
1'-0 3/4" TOF 85'-0" WF2 2'-5" 1'-0" 1'-5 1/4" #4@8" OC. #4@8" OC. #4@8" OC. (3)#4 #4@8" OC.

16
SEE PLAN FOR
LOCATION
WF4 3'-2" 1'-0" 1'- 2 1/2" #4@8" OC. #4@8" OC. #4@8" OC. (3)#4 #4@8" OC.
SC15
WF5 3'-2" 1'-0" 1'- 2 1/2" #4@8" OC. #4@8" OC. #4@8" OC. (3)#4 #4@8" OC.
3'-0"

3'-0"

3'-0"
P4
4.0

1'-8"
UNLESS NOTED OTHERWISE:
- SEE DETAIL 4/S3.00

4'-0"
6
S3.02

2'-4"
SC8

2'-4"
SC8
3'-0"

3'-0"

3'-0"
TYP. P4 P3
2
S3.00 5'-8 3/4"

7"
SC3 SC3
3'-0" 3'-0" 1'-9" 1'-9"
3.9 PIER SCHEDULE CONC. f'c = 4000 PSI

4'-0"
3'-0" 3'-0"

REINFORCING
MARK SIZE VERTICAL TIES HOOKS N (*) REMARKS
4'-8" 8'-8" 4'-8 1/4" P1-A 2'-0" x 2'-8 1/2" (20)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.

F1 '-1"
P1-B 2'-0" x 2'-8 1/2" (20)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.

86
2
P2 2'-8" x 2'-8 1/2" (24)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
P3 2'-8" x 2'-0" (20)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
P4 2'-0" x 2'-0" (12)#6 #3@10" OC. 3@1 1/2" OC.
P5 3'-0" x 2'-0" (18)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
P6 2'-8" x 3'-0 1/4" x 2'-10 1/4" (21)#7 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.

WF1
P7 2'-9" x 3'-1 1/4" x 2'-10 3/4" (21)#7 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC. C 2022 Quetica Professional Engineers, Inc.
All rights reserved.
4 P8 2'-6 1/2" x 2'-0" (16)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC. This document is an instrument of service and is the property of
S3.00

22'-7"
P9 2'-0" x 2'-0" (12)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC. Quetica Professional Engineers, Inc. and may not be used or copied
without prior written consent.
P10 2'-0" x 2'-0" (12)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
5 1/4" 1'-2" UNLESS NOTED OTHERWISE:
- SEE DETAILS 1/S3.00
- PIERS TOP OF SURACE ELEVATION (TOS) 87'-6"
- FOR ANCHOR BOLTS SEE DETAIL 1/S4.00

CONC. f'c = 3500 PSI

87 F5

87 F5
"

"
'-0

'-0
COLUMN FOOTING SCHEDULE ALLOWABLE SOIL STRESS

F6 -1"
86
BEARING: SEE S0.00

'
4 REINFORCING
S3.07
4'-0"

4'-0"
MARK SIZE DEPTH SHORT-WAY LONG-WAY REMARKS
SC15

3'-0"
P4 P4 P3
F1 4'-0"x4'-0" 1'-6" (7)#5 HOOK (7)#5 HOOK

2'-0"
F2 18'-0"x10'-0" 2'-1" (15)#6 (27)#6 TOP AND BOTTOM
3.0 F3 6'-0"x6'-0" 1'-6" (10)#5 (10)#5 TOP AND BOTTOM
TYP.

2'-0"
SC13 F4 14'-0"x4'-0" 2'-1" (7)#5 (21)#5 HOOK

3'-0"
FOUNDATION BEAM SC13 SC2 SC2 F5 8'-0"x8'-0" 2'-1" (13)#6 (13)#6 TOP AND BOTTOM
S3.01
4'-0"

4'-0"
10

18" x 25" F6 14'-0"x6'-0" 2'-1" (9)#6 HOOK (21)#5 TOP AND BOTTOM
2'-0" 2'-0" F7 9'-0"x4'-0" 2'-1" (7)#6 (14)#5 HOOK

85 F1
"
'-6
F8 15'-0"x13'-0" 1'-6" (20)#5 (24)#5 TOP AND BOTTOM
2'-8" 8'-8" 2'-8 1/4" F9 9'-0"x9'-0" 1'-6" (14)#5 (14)#5 TOP AND BOTTOM
4'-0" 4'-0" 4'-0" 4'-0" F10 6'-0"x6'-0" 1'-8" (10)#5 (10)#5
F11 11'-0"x7'-0" 1'-6" (11)#5 (17)#5 TOP AND BOTTOM
F12 18'-0"x8'-0" 2'-1" (13)#6 (27)#5 TOP AND BOTTOM
F13 9'-0"x9'-0" 2'-11" (14)#6 (14)#6 TOP AND BOTTOM

WF1
F14 3'-6"x6'-0" 1'-6" (6)#5 (10)#5
F15 8'-0"x8'-0" 1'-10" (7)#7 (7)#7 BOTTOM
F16 6'-0"x6'-0" 1'-6" (8)#5 (8)#5 BOTTOM
F17 20'-0"x9'-0" 2'-6" (9)#7 (12)#8 TOP AND BOTTOM
4" CONCRETE SLAB-ON-GRADE 4
F18 9'-0"x9'-0" 2'-0" (8)#7 (8)#7 BOTTOM
AB

23'-3"
S3.00

TOF 85'-0"
F19
F20
10'-0"x10'-0"
12'-0"x13'-0"
2'-2"
2'-6"
(10)#7
(12)#8
(10)#7
(12)#8
TOP AND BOTTOM
TOP AND BOTTOM
CD
F21 12'-0"x12'-0" 2'-6" (10)#8 (10)#8 TOP AND BOTTOM
F22 9'-0"x4'-0" 2'-1" (7)#6 (10)#7 TOP AND BOTTOM
SEE DRAWING 2/S3.00 AND 3/S3.00 E F
HOOK: TYPICAL HOOK REQUIRED ON BOTH SIDES
G H
86 F5
"
'-5

2'-8" 8'-8" 2'-8 1/4"

KEY PLAN
FOOTING AND FOUNDATION PLAN - AREA 'B'
1
4'-0"

4'-0"

1/4" = 1'-0"
3'-0"

0 I hereby certify that this plan, specifcation or report was

prepared by me or under my direct supervision and that I
2.0 am a duly Licsened Professional Engineer under the laws
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

of the state of Minnesota.

SC10 UNLESS NOTED OTHERWISE:
3'-0"

SC11 SC1 SC1

1. SEE STRUCTURAL NOTES SHEET S0.00 FOR MORE INFORMATION.
4'-0"

4'-0"

2. SEE ARCHITECTURAL DRAWINGS FOR LOCATIONS OF RAMPS, SLAB SLOPES, STEPPED SLABS AND PARTITION
WALLS. Katherine Russell
2'-8" 3. REFER TO ARCHITECTURAL DRAWINGS FOR ADDITIONAL INFORMATION AND DIMENSIONS. P27101
Date 12/30/2022 Lic. No.

FOUNDATION BEAM
1'-0 3/4" 4. PROVIDE 4" SLAB ON GRADE REINFORCE WITH MICRO FIBERS AT 1.5 POUNDS PER CUBIC YARD . REFER TO

F6 -1"
86
5 1'-7 1/4"
ARCHITECTURAL AND CIVIL DESIGN FOR GRANULAR BASE MATERIAL UNDER SLAB ON GRADE. SEE DETAIL 1/S3.02

'
4'-0" 4'-0" 4'-0" 4'-0" S3.00 Revisions
86 F5

5. SEE SLAB ON GRADE DETAILS IN DRAWING S3.00.

32" x 42"
"

TYP.
'-5

Description Date Num

FOUNDATION BEAM

FOUNDATION BEAM

6. PROVIDE VAPER BARRIER DIRECTLY BELOW SLAB ON GRADE INSIDE.

FOUNDATION BEAM

7. TOP OF GROUND SLAB ELEVATION (TOS) - TYP. 88'-0", SEE ARCH FOR SPECIAL SLOPED AREAS.
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

8. GRADE BEAMS:
36" x 38"

36" x 38"

a. SEE TOP OF BEAMS ON SECTIONS.

36" x 38"

b. SEE SECTIONS FOR GEOMETRY AND REINFORCEMENT.

LAP REINFORCING AS FOLLOWS:
5 BAR N° OTHER TOP
S3.00 #4: 24" 30"
TYP. TYP. TYP.
5 5 #5: 28" 38"

23'-5"
S3.00 S3.00 #6: 34" 44"
2'-8" 8'-8" 2'-8 1/4"
GRADE BEAM REINFORCEMENT MUST NOT BE INTERRUPTED IN PIERS OR FOUNDATIONS.
9. WALL FOUNDATION:
F7 -5"
F7 -5"

4'-6" 4'-6" 4'-6" 4'-6" a. TYP. TOP OF WALL = 88'-0", TYP. BOTTOM OF WALL SEE SECTIONS ON PLANS.
86
86

'
'

b. SEE SECTIONS FOR GEOMETRY AND REINFORCEMENT DETAILS.

28/12/2022 10:51:21

c. WALL AND FOUNDATION REINFORCEMENT MUST NOT BE INTERRUPTED IN PIERS AND FOUNDATIONS.
Comm: 216050
4'-0"

10. WALL FOUNDATION REINFORCEMENT MUST NOT BE INTERRUPTED AT FOOTINGS OR PIERS, REINFORCEMENT TO BE Date: 12/30/2022
ANCHORED AND LAPPED PROPERLY.
4'-0"

4'-0"

11. SEE THIS SHEET AND SHEET S4.00 FOR SCHEDULES. Drawn:
12. INDICATES COLUMN BLOCKOUT SECOND STAGE CONCRETE. North
Check:
13. COORDINATE WITH ARCHITECTURE DESIGN EXISTING GROUND SLAB CONNECTION; SEE 4/S3.02 AND 5/S3.02
6
F4 -1"

15
86

FOUNDATION BEAM S3.01

FOUNDATION BEAM
'

S3.01
FOOTING AND
5'-7 1/2"

36" x 23" TYP.

36" x 23"
4'-7 1/2"

4'-7 1/2"

FOUNDATION BEAM
1'-6 1/2"

10 1/2"

SC1
SC4
18" x 23"
SC4 SC1
FOUNDATION
S 1.0 PLAN - AREA 'B'
7 1/2"

2'-4"

X.1
6"
TYP.

4'-11" 10'-10 1/2"

8
TYP.

TYP.
TYP.

_______
10
TYP.

S3.07
5'-7 1/2" S3.00
S3.00

FOUNDATION BEAM
9

S3.01

S3.02
S3.01

S3.02
S3.02
4

5
4

36" x 23"
5
4

Scale: As indicated
S3.01
7
S3.01

COORDINATE W/
PERMIT SET
8

EXISTING. BLDG. TOF 85'-8" EXISTING. BLDG. TOF 85'-8" ARCH DESIGN
X.C X.B EXISTING. BLDG. TOF 85'-8" X.A.4 EXISTING. BLDG. TOF 85'-8"
X.A
NOT FOR CONSTRUCTION S2.00b
 Winneshiek
Expansion and
7.68 F.966.68 9.86 D.22 10.86 11.86 C.22 12.86 B.22 1.109 A.22 14.86 INDICATES Renovation
FOOTING MARK

F3 - 6"
31'-3" 26'-9" 9'-3" 11" 85
' 901 Montgomery St
Decorah, IA 52101
INDICATES
TOP 216051
OF FOOTING

Winneshiek Medical
Center
Decorah, IA 52101

IA EXISTING BUILDING EXISTING BUILDING EXISTING BUILDING

EXISTING BUILDING
TOF 84' - 7 3/8" 84' - 7 3/8" 84' - 7 3/8"
84' - 7 3/8"
FOUNDATION LEGEND
EXISTING HOSPITAL 1968 BUILDING

EXISTING FIN. FLOOR ELEV.

MATCH EXIST. (877' 5 1/3")
EXTERNAL WALL EXIST LEVEL. (877' 3 1/3") WALL FOUNDATION SCHEDULE
DIMENSIONS WALL REINFORCEMENT FOUNDATION REINFORCEMENT
MARK REMARKS
STARTERS
B H T VERT REINF HORIZ REINF TRANV REINF LONG REINF
BARS
WF1 2'-2" 1'-0" 1'-2" #4@8" OC. #4@8" OC. #4@8" OC. (3)#4 #4@8" OC.

S3.00
4
ADDITIONAL REINF,
SEE DETAIL 8/S3.00,

S3.02
WF2 2'-5" 1'-0" 1'-5 1/4" #4@8" OC. #4@8" OC. #4@8" OC. (3)#4 #4@8" OC.

S3.00
SEE PLAN FOR

12
LOCATION

S3.02
1'-11" 1'-5 1/4" 6'-8" 3'-5 3/4" EXISTING BUILDING

S3.02

13
WF4 3'-2" 1'-0" 1'- 2 1/2" #4@8" OC. #4@8" OC. #4@8" OC. (3)#4 #4@8" OC.

4
TOF 84' - 7 3/8" 3'-0" 3'-0" WF5 3'-2" 1'-0" 1'- 2 1/2" #4@8" OC. #4@8" OC. #4@8" OC. (3)#4 #4@8" OC.

84 16
"
EXISTING BUILDING EXISTING BUILDING EXISTING BUILDING

'-0
F
TOF 84' - 7 3/8" TOF 84' - 7 3/8" TOF 84' - 7 3/8"
G.96
1'-1 3/4"

4'-0"
WF5
X.F

3'-0"
1'-3 3/4"
11 3/4"

1'-2 1/2"
P10 SC20

3'-2"
4.22 SC20 SC20

2'-8 1/4"
SC20

3'-0"
4'-6" 4'-6"

F2 '-0"
P9 P9 PIER SCHEDULE CONC. f'c = 4000 PSI

87

4'-8 1/4"

4'-0"
2

3'-2"
1.96. _______
10
S3.00 REINFORCING
3'-0" MARK SIZE VERTICAL TIES HOOKS N (*) REMARKS
P1-A 2'-0" x 2'-8 1/2" (20)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.

4'-0"
EXISTING BUILDING TOF 84'-0"
TOF 82' - 3/8" 5 P1-B 2'-0" x 2'-8 1/2" (20)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
F1 '-0" P2 2'-8" x 2'-8 1/2" (24)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
84 TOF 84'-0" P3 2'-8" x 2'-0" (20)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
3'-0"

2.96. 4'-0" 4'-0"

P4 2'-0" x 2'-0" (12)#6 #3@10" OC. 3@1 1/2" OC.
C 2022 Quetica Professional Engineers, Inc.
P5 3'-0" x 2'-0" (18)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC. All rights reserved.
4'-4 1/8"

9'-0" 1'-6 1/8" This document is an instrument of service and is the property of
P6 2'-8" x 3'-0 1/4" x 2'-10 1/4" (21)#7 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC. Quetica Professional Engineers, Inc. and may not be used or copied
P7 2'-9" x 3'-1 1/4" x 2'-10 3/4" (21)#7 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC. without prior written consent.
EXISTING BUILDING
TOF 82' - 3/8" P8 2'-6 1/2" x 2'-0" (16)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
TYP. P9 2'-0" x 2'-0" (12)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.
5 P10 2'-0" x 2'-0" (12)#6 #3@10" OC. (4)#3@10" OC. 3@1 1/2" OC.

WF4
S3.00
UNLESS NOTED OTHERWISE:
8"

28'-6"
- SEE DETAILS 1/S3.00
27'-4 1/4"

8" 8"
6'-0" 1'-1" - PIERS TOP OF SURACE ELEVATION (TOS) 87'-11 3/8"
5'-9 1/2"

5'-1 1/2"

4" CONCRETE SLAB-ON-GRADE - FOR ANCHOR BOLTS SEE DETAIL. 1/S4.00

FOUNDATION BEAM
12
S3.02
4

36" x 38"
S3.00
8"

7 8"
F1 3/
'-8
87

EXISTING BUILDING

87 21
"
'-0
F
TOF 82' - 3/8" 11"
10'-3 3/8"

4'-0"

84 18
"
4

'-0
F
S3.02 3'-0" 3'-0" CONC. f'c = 3500 PSI

84 16
COLUMN FOOTING SCHEDULE

"
'-0
F
ALLOWABLE SOIL STRESS
2

6'-0"
BEARING: SEE S0.00
F2 '-0"
6.96. 87
12

4'-6"
FOUNDATION BEAM S3.00 REINFORCING

3'-0"
1'-1 1/2" P9
SC18 MARK SIZE DEPTH SHORT-WAY LONG-WAY REMARKS
P10
3 F1 4'-0"x4'-0" 1'-6" (7)#5 HOOK (7)#5 HOOK
9'-0"

1'-0"
3.22 EXISTING BUILDING
TOF 82' - 3/8" TYP.
S3.00 F2 18'-0"x10'-0" 2'-1" (15)#6 (27)#6 TOP AND BOTTOM
3'-2" F3 6'-0"x6'-0" 1'-6" (10)#5 (10)#5 TOP AND BOTTOM
SC16 SC17

3'-0"
SC16 TOF 84'-0" F4 14'-0"x4'-0" 2'-1" (7)#5 (21)#5 HOOK

4'-6"
EXISTING HOSPITAL BUILDING 1996 36" x 38" F5 8'-0"x8'-0" 2'-1" (13)#6 (13)#6 TOP AND BOTTOM

6'-0"
6" SLAB ON 24" OF STRUCTURAL
F6 14'-0"x6'-0" 2'-1" (9)#6 HOOK (21)#5 TOP AND BOTTOM
FILL REINF. W/6X6 - W2.9 X W2.9 WWF 17
S3.01 TOF 84'-0" F7 9'-0"x4'-0" 2'-1" (7)#6 (14)#5 HOOK AB
TYP.

F8 15'-0"x13'-0" 1'-6" (20)#5 (24)#5 TOP AND BOTTOM

5'-4" 4'-9 3/4" F9 9'-0"x9'-0" 1'-6" (14)#5 (14)#5 TOP AND BOTTOM CD
S3.00
13'-11 1/2"

13'-11 1/2"
F10 6'-0"x6'-0" 1'-8" (10)#5 (10)#5

S
5

14'-7 1/2"
4'-6" 4'-6" F11 11'-0"x7'-0" 1'-6" (11)#5 (17)#5 TOP AND BOTTOM

WF4
EXISTING FIN. FLOOR
ELEV. (88' 5 3/8") 6'-0" 6'-0"
TOF 82'-11 3/8" F12
F13
18'-0"x8'-0"
9'-0"x9'-0"
2'-1"
2'-11"
(13)#6
(14)#6
(27)#5
(14)#6
TOP AND BOTTOM
TOP AND BOTTOM
E F

2'-0"
4
F14 3'-6"x6'-0" 1'-6" (6)#5 (10)#5
S3.02 UNDERGROUND PIPE,
SEE MECH. DESIGN, F15 8'-0"x8'-0" 1'-10" (7)#7 (7)#7 BOTTOM
G H
IN. EL.= 79'-9" F16 6'-0"x6'-0" 1'-6" (8)#5 (8)#5 BOTTOM
F17 20'-0"x9'-0" 2'-6" (9)#7 (12)#8 TOP AND BOTTOM

1'-3 5/8"
6
S3.02 F18 9'-0"x9'-0" 2'-0" (8)#7 (8)#7 BOTTOM
F19 10'-0"x10'-0" 2'-2" (10)#7 (10)#7 TOP AND BOTTOM
F20 12'-0"x13'-0" 2'-6" (12)#8 (12)#8 TOP AND BOTTOM KEY PLAN
2.22 F21 12'-0"x12'-0" 2'-6" (10)#8 (10)#8 TOP AND BOTTOM

8"
11" 9'-4" 9 3/4" F22 9'-0"x4'-0" 2'-1" (7)#6 (10)#7 TOP AND BOTTOM
9 4'-0" 4'-0" TOF 82'-11 3/8" I hereby certify that this plan, specifcation or report was

8"
EXISTING BUILDING F1 '-0" 1'-7 5/8" 8" 8" prepared by me or under my direct supervision and that I
TOF 82' - 3/8" 84 UNDERGROUND PIPE, 8'-4 1/2" am a duly Licsened Professional Engineer under the laws
84 15
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

SEE MECH. DESIGN,

"

of the state of Minnesota.

'-0
F

IN. EL.= 82'-5"

8'-4"

7'-10 3/4"

7'-8"
7'-8"
12'-0"
11 Katherine Russell
FOOTING AND FOUNDATION PLAN - AREA 'H'
5'-0"

S3.02 1'-6"
1 Date 12/30/2022 P27101
4'-0"

Lic. No.
SC17 P9 WF4 SC17 P9 WF4 1/4" = 1'-0"
0
12.96 S 15 Revisions

1'-6"
8"
S3.02
1.22

10 3/4"
0 /8" Description Date Num
F2 1 3 UNLESS NOTED OTHERWISE:
1'-2 1/2"
3'-2"
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

'-1 1. SEE STRUCTURAL NOTES SHEET S0.00 FOR MORE INFORMATION.

82 2. SEE ARCHITECTURAL DRAWINGS FOR LOCATIONS OF RAMPS, SLAB SLOPES, STEPPED SLABS AND
4'-0"

EXISTING BUILDING
PARTITION WALLS.
5'-0"

TOF 82' - 3/8" 1'-6" DEEP SUMP PIT.

3. REFER TO ARCHITECTURAL DRAWINGS FOR ADDITIONAL INFORMATION AND DIMENSIONS.
SEE SECTION 15/S3.02
4. PROVIDE 4" SLAB ON GRADE REINFORCE WITH MICRO FIBERS AT 1.5 POUNDS PER CUBIC YARD. REFER TO
SEE ARCHITECTURAL/

1'-5 5/8"
TOF 84'-0" ARCHITECTURAL AND CIVIL DESIGN FOR GRANULAR BASE MATERIAL UNDER SLAB ON GRADE. SEE DETAIL
TOF 82'-11 3/8" MECHANICAL DRAWINGS
TOF 82'-11 3/8" 1/S3.02
FOR LOCATION AND SIZE
TYP.

3" TOF 84'-0" 5. SEE SLAB ON GRADE DETAILS IN DRAWING S3.00.

13'-0" 6. PROVIDE VAPER BARRIER DIRECTLY BELOW SLAB ON GRADE INSIDE.
7. TOP OF GROUND SLAB ELEVATION (TOS) - TYP. 88'-5 3/8", SEE ARCH FOR SPECIAL SLOPED AREAS.
S3.00

S3.00

S3.00

S3.00

S3.00
12

12
4

8. GRADE BEAMS:
a. SEE TOP OF BEAMS ON SECTIONS.
28/12/2022 10:51:23

b. SEE SECTIONS FOR GEOMETRY AND REINFORCEMENT.

LAP REINFORCING AS FOLLOWS: Comm: 216050
BAR N° OTHER TOP
EXISTING BUILDING 1'-5 1/4" #4: 24" 30" Date: 12/30/2022
EXISTING BUILDING
TOF 82' - 3/8" #5: 28" 38"
TOF 82' - 3/8" Drawn:
#6: 34" 44"
F.96 G.96 9.
GRADE BEAM REINFORCEMENT MUST NOT BE INTERRUPTED IN PIERS OR FOUNDATIONS.
WALL FOUNDATION:
Check: North

a. TYP. TOP OF WALL = 88'-5 3/8", TYP. BOTTOM OF WALL SEE SECTIONS ON PLANS.
b. SEE SECTIONS FOR GEOMETRY AND REINFORCEMENT DETAILS.
c. WALL AND FOUNDATION REINFORCEMENT MUST NOT BE INTERRUPTED IN PIERS AND
FOUNDATIONS. FOOTING AND
10. WALL FOUNDATION REINFORCEMENT MUST NOT BE INTERRUPTED AT FOOTINGS OR PIERS,
REINFORCEMENT TO BE ANCHORED AND LAPPED PROPERLY.
FOUNDATION
S
11.
12.
13.
SEE THIS SHEET AND SHEET S4.00 FOR SCHEDULES.
INDICATES COLUMN BLOCKOUT SECOND STAGE CONCRETE.
COORDINATE WITH ARCHITECTURE DESIGN EXISTING GROUND SLAB CONNECTION; SEE 4/S3.02 AND 5/S3.02
PLAN - AREA 'H'

Scale: As indicated

PERMIT SET
NOT FOR CONSTRUCTION S2.00h
 E.4 D.99 D.57 D.2 B.65 B.9
Winneshiek
Expansion and
11'-4" 9'-9 1/4" 13'-8 3/4" 11'-6 1/8" 16'-11 7/8"
Renovation

AREA A

AREA B
E.6 MAIN LEVEL FLOOR PLAN - AREA 'A'
1 1/4" = 1'-0" 901 Montgomery St

1'-1 1/4"
0
Decorah, IA 52101

S3.04

S3.04
14

14
1

S3.04
14
S3.07
216051

TYP.

TYP.
1 1
1 UNLESS NOTED OTHERWISE:

TYP.
W18X35 W27X84 W27X84 1. SEE SHEET S0-00 FOR STRUCTURAL NOTES, ABBREVIATIONS AND SYMBOLS. Winneshiek Medical
5.0 2. SEE SHEET S4.00 FOR SCHEDULES
16 9, 9, 9, 9 9, 9, 9, 9
3. TOP OF SLAB ELEVATION = 100'-0" UNLESS OTHERWISE NOTICED Center

2" COMPOSITE DECK 20 GA. W/ 4 1/2" THICK CONCRETE

TYP. 11 4. 2" - 20GA. COMPOSITE DECK W/ 2 1/2" NORMAL WEIGHT CONCRETE (4 1/2" TOTAL THICKNESS) UNLESS Decorah, IA 52101
14 S3.04 OTHERWISE NOTICED. REINFORCE W/ SYNTHETIC MACRO FIBER REINFORCING ACCORDING TO THE
S3.04 TYP. SPECIFICATIONS.

6'-0"

S3.04
TYP. 5. TYPICAL TOP OF STEEL BEAM EL. = 99'-7 1/2".

15
18 6. SEE STRUCTURAL NOTES FOR TYPICAL OPENING FRAMING. COORDINATE WITH ARCHITECTURAL AND
S3.04 MECHANICAL DRAWINGS FOR OPENING LOCATION AND SIZE. SEE 19/S3.04 FOR DETAIL.

TYP.
8 5/8" 7. SEE ARCHITECTURAL DRAWINGS FOR LOCATION OF RAMPS, SLAB SLOPES, STEPPED SLABS PARTITION

IA W10X17
8
TYP.
15
S3.04
15
S3.04
TYP.
8.
9.
WALLS AND STAIRS.
REFER TO ARCHITECTURAL DRAWINGS FOR ADDITIONAL INFORMATION AND DIMENSIONS.
FOR BEAMS WITH MECHANICAL PENETRATIONS, SEE 1- 4/S3.04 .
10. SEE TYPICAL COLUMN TO BEAM CONNECTIONS 5/S3.04, 6/S3.04 & 7/S3.04 AND SCHEDULE SHEET S4.00.

(TOTAL)
W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35
11. ALL COMPOSITE SLAB EDGES TO BE FIELD VERIFIED PRIOR TO STRUCTURE FABRICATION.

5, 6, 5

6,5,5
17'-8"

16

16

16

16

16

16

16

16
12. SEE SHEET S3.04 FOR TYPICAL COMPOSITE SYSTEM DETAILS.

6'-0"

1
5'-10 1/2" 2 EQ SPS @ 5'-10 1/2"=11'-9" 5'-10 1/2" 7'-1 1/2" 2 EQ SPS @ 7'-1 1/2"=14'-3" 7'-1 1/2"
W10X17
8
SINGLE PLATE
CONECTION

5'-8"

S3.04
S3.04

S3.04

12
12

12
4

TYP.
TYP.

TYP.
4
W18X35 W18X35 W14X61 W14X61 W30X90
4.0 4 3 13 W14X22 16, 10 6, 10, 10 10, 10, 10, 10
S3.05 3
16
E.4 E.6 D.99 D.57 D.2
3"

1'-0"
S3.05
1
1
_______
2 S3.05
S2.01a 9'-9 13/16" 3 11/16"
3' 2 #5 L=27'-6"
3 1/2" 5.0 2 #5 5.0
1 3'
12'-7 5/8"

S3.05 TYP. TYP.

15 15 3'
S3.04 S3.04 2 #5
3'

4
4

1
W 18X35

W18X35
1

6,8,1
16

W21X44

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35
S3.04

S3.05
24'-11"

1,6,8,1
3'
14

16

16

16

16

16

16

16

16
2
3' 2 #5
TYP.

8 5/8" 2 #5 L=30'-9"
W14X22
8,8 4.0 4.0
3"

C 2022 Quetica Professional Engineers, Inc.

All rights reserved.
This document is an instrument of service and is the property of
TYP. Quetica Professional Engineers, Inc. and may not be used or copied
16 15 without prior written consent.
S3.04 S3.04 2#5
W10X17

11" 5'-2 1/2" 5'-2 1/2" 2 #5 L=38'-9"

8

S3.04
20
11 3/8"

5'-10 1/2" 2 EQ SPS @ 5'-10 1/2"=11'-9" 5'-10 1/2" 7'-1 1/2" 2 EQ SPS @ 7'-1 1/2"=14'-3" 7'-1 1/2"
4
3.1 W18X35 3'
2 #5
2 #5 L=32'-7"
TYP.

6,5,3,2
S3.04
S3.04

3'

S3.04
12
12

3'

12
S3.04

1 2 #5
12
2'-1"

3' 3'
TYP.
TYP.

TYP.
4 4
3" 6'-0" 3"
W14X61 W14X61 W30X90 3' 2 #5 2 #5 L=33'-5"
3.0 16, 10 6, 10, 10 10, 10, 10, 10
9'-6 3/8"

3
3.1 3.1
8'-4"

16 2" COMPOSITE DECK 20 GA. W/ 4 1/2" THICK CONCRETE

S3.04
16
(TOTAL) 3.0 2 #5 L=29'-3" 3.0
S3.04
W18X35
1

W14X22
16

2 #5
W18X35

5 TYP. TYP.
12 15 15 3'
3"

S3.07
TYP.
16

7 S3.04 S3.04 3' 3'

15'-5"

S3.07 3'
3' 2 #5
S3.04

3' 2 #5 L=44'-11"
14

2 #5 2 #5
4'-11" 6'-6" 1'-11 7/8"
2.3 2.3
9'-4 3/4"
1
--- W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35
23'-3"

9,7

9,7

16

16

16

16

16

16

16

16

16
TYP.
AB
-

15
S3.04 E.6 E.4 D.99 D.2
2.3
W18X35 CD
7, 7, 2

E F
TYP.

1'-3 1/2"

5'-10 1/2" 2 EQ SPS @ 5'-10 1/2"=11'-9" 5'-10 1/2" 7'-1 1/2" 2 EQ SPS @ 7'-1 1/2"=14'-3" 7'-1 1/2"
E.6 DIAPHRAGM ZONE 1 - Added Reinforcement.
G H
7'-10"

2
S3.04

1/8" = 1'-0"
14

1'-4 5/16" 0

S3.04
S3.04

12
12

TYP.
TYP.

4 4
2.0
W30X90
10, 10, 10, 10
W14X61
16, 10
W16X77
INDICATES
KEY PLAN
5, 15, 15
PROFILE SECTION (u): INDICATES
POSITIVE BEAM
4'-7 1/8"

CAMBER IN INCHES I hereby certify that this plan, specifcation or report was
16 prepared by me or under my direct supervision and that I
S3.04 W AXB (u) am a duly Licsened Professional Engineer under the laws
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

of the state of Minnesota.

EXIST W14X22 n
1.07 TOB 99'-6 1/2" INDICATES
TYP. TYP. NO OF 3/4" Ø x 3"
15 15 Katherine Russell
HEADED STUDS;
S3.04 S3.04 SEE 10/S3.04 Date 12/30/2022 Lic. No. P27101

12 Revisions
S3.03 TAG BEAM LEGEND Description Date Num
4
21'-4 1/8"
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35
1

W18X35
W30X90

W18X35
23'-5"

3,26,11

16

16

16

16

16

16
16

16
EXIST W14X22
EXIST 16K3

EXIST 16K3

TOB 99'-9"
TOB 99'-9"
TOB 99'-9"

KEYNOTES
5'-10 1/2" 2 EQ SPS @ 5'-10 1/2"=11'-9" 5'-10 1/2" 7'-1 1/2" 2 EQ SPS @ 7'-1 1/2"=14'-3" 7'-1 1/2" PROVIDE SLIP CRITICAL CONNECTION AT BEAM ENDS.
1
28/12/2022 10:51:25

DOUBLE
EXIST 1" COMP. 2 COORDINATE WITH ARCHITECTURAL DESIGN FOR HANDRAIL AND STAIR ACCESS.
ANGLE Comm: 216050
DECK 22 GA. W/ CONNECTION
3" CONC. Date: 12/30/2022
3 BRACE COLUMN DURING CONST. STAGE UNTIL DECK CONCRETE REACHES 0.7(f'c).
Drawn:
Check: North
1.112
1'-7 5/8"

4 PROVIDE A DOUBLE ANGLE CONNECTION

1 1
10"

1.0
EXIST W16X36
TOB 99'-6 1/2"
W27X84
9, 9, 9, 9
W27X84
9, 9, 9, 9 MAIN LEVEL
2'-0 7/8"

2'-4"

2.07 FLOOR FRAMING

TYP.

EXIST W10X22 TOB 99'-8" EXIST W16X31 TOB 99'-8" X.1

S
EXIST W16X31 TOB 99'-8"
PLAN - AREA - 'A'
S3.03

S3.03
S3.05

S3.03
12

13
12
EXIST W14X22

EXIST 20KSP EXIST 18KSP EXIST 20KSP

EXIST 16K3

EXIST 16K3

TOB 99'-8" TOB 99'-8"

EXIST W18X50
TOB 99'-5 1/2"

TOB 99'-8"
COMP. DECK 22
GA. W/ 4" THICK

EXIST 36" DEEP

TRUSS GIRDER
EXIST 36" DEEP
TRUSS GIRDER

TOB 99'-5 1/2"

TOB 99'-5 1/2"
EXIST 1 1/2"

CONC.

1/2"
EXIST 20KSP EXIST 18KSP EXIST 20KSP Scale: As indicated
TOB 99'-8" TOB 99'-8" TOB 99'-8"
1'-8 1/2"
PERMIT SET
E.7.07 F.07 X.E X.D X.C
NOT FOR CONSTRUCTION S2.01a
 B.9 A.9 A.4 A.1 1.91 Winneshiek
Expansion and
29'-4" 20'-0 1/4" 6'-6 3/4" 8'-8" Renovation

AREA A

AREA B

---
-
901 Montgomery St
Decorah, IA 52101

1'-1 1/4"
216051

S3.04

S3.04
1'-1 1/4"
14

14

S3.04
18
1
Winneshiek Medical

TYP.

TYP.
1

TYP.
1
W27X84
9,9,9,9
W27X84 W18X35
5.0 Center
9,9,9,9
Decorah, IA 52101
TYP.
1
S3.06 TYP.
18
S3.04

IA

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W30X90

W24X68
4, 7, 29

14'-2 1/2"
1
5,0
16

16

16

16

16

16

16

16

1
2 3

17'-8"
S3.07 S3.07

7'-4" 2 EQ SPS @ 7' - 4" = 14' - 8" 7'-4" 6'-8" 2 EQ SPS @ 6' - 8" = 13' - 4" 6'-7" 6"

S3.05

S3.04
16
1

2 3/4"
TYP. TYP. 2
15 15
S3.04 S3.04
W14X22

S3.04
10

12

3'-5 1/2"
TYP.
11

TYP.
S3.04
4
W30X90 W16X77 W10X17
10,10,10,10 11, 12, 11 6 4.0

2'-4"
W10X17
8 3.9

5'-7"
W10X17
8

W18X35

W18X35
W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

4,4,4,4

4,4,4,4
16

16

16

16

16

16

16

16

1
2 EQ SPS @ 5'-8" = 11'-4"
14

24'-11"
S3.04
TYP.
TYP. TYP. TYP. W10X17
15 15 15

TYP.
TYP. 8 C 2022 Quetica Professional Engineers, Inc.
S3.04 S3.04 S3.04 All rights reserved.
11 This document is an instrument of service and is the property of
S3.04

S3.04
Quetica Professional Engineers, Inc. and may not be used or copied

15
1'-0 3/4" without prior written consent.

7'-4" 2 EQ SPS @ 7' - 4" = 14' - 8" 7'-4" 6'-8" 2 EQ SPS @ 6' - 8" = 13' - 4" 6'-7"

W10X17
8

TOS 100'-0"

5'-8"
S3.04
12
4
S3.07
INDICATES

TYP.
1 PROFILE SECTION (u): INDICATES
4 1 POSITIVE BEAM
W30X90 W16X77 W10X17 W10X17
10,10,10,10 11, 12, 11 6 8 3.0 CAMBER IN INCHES
W AXB (u)

2" COMPOSITE DECK 20 GA. W/ 4 1/2" THICK CONCRETE

n
A.4

5'-9"
TYP. INDICATES
11
S3.04 NO OF 3/4" Ø x 3"
HEADED STUDS;
2" COMPOSITE DECK 20 GA. W/ 4 1/2" THICK CONCRETE SEE 10/S3.04
(TOTAL) W10X17
8
TAG BEAM LEGEND

(TOTAL)
W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35
4,4,4,4

4,4,4,4
16

16

16

16

16

16

16

16

1
2 EQ SPS @ 5'-10" = 11'-8"

23'-3"
W10X17
8
TYP. TYP. AB
15 15
S3.04 S3.04
CD
MAIN LEVEL FLOOR PLAN - AREA 'B'
1 1/4" = 1'-0"
7'-4" 2 EQ SPS @ 7' - 4" = 14' - 8" 7'-4" 6'-8" 2 EQ SPS @ 6' - 8" = 13' - 4" 6'-7" W10X17 14
0
E F
S3.04
8 TYP.
G H

5'-10"
S3.04
12

UNLESS NOTED OTHERWISE:

TYP.

1.
2.
SEE SHEET S0-00 FOR STRUCTURAL NOTES, ABBREVIATIONS AND SYMBOLS.
SEE SHEET S4.00 FOR SCHEDULES
KEY PLAN
W30X90 W30X90 W10X17
10,10,10,10 10,10,10,10 8 2.0 3.
4.
TOP OF SLAB ELEVATION = 100'-0" UNLESS OTHERWISE NOTICED
2" - 20GA. COMPOSITE DECK W/ 2 1/2" NORMAL WEIGHT CONCRETE (4 1/2" TOTAL THICKNESS) UNLESS
OTHERWISE NOTICED. REINFORCE W/ SYNTHETIC MACRO FIBER REINFORCING ACCORDING TO THE I hereby certify that this plan, specifcation or report was
SPECIFICATIONS. prepared by me or under my direct supervision and that I
5. TYPICAL TOP OF STEEL BEAM EL. = 99'-7 1/2". am a duly Licsened Professional Engineer under the laws

5'-11"
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

14 of the state of Minnesota.

S3.04 6. SEE STRUCTURAL NOTES FOR TYPICAL OPENING FRAMING. COORDINATE WITH ARCHITECTURAL AND
TYP. MECHANICAL DRAWINGS FOR OPENING LOCATION AND SIZE SEE 19/S3.04 FOR DETAILS.
7. SEE ARCHITECTURAL DRAWINGS FOR LOCATION OF RAMPS, SLAB SLOPES, STEPPED SLABS PARTITION
WALLS AND STAIRS.
Katherine Russell
W10X17 8. REFER TO ARCHITECTURAL DRAWINGS FOR ADDITIONAL INFORMATION AND DIMENSIONS.
9. FOR BEAMS WITH MECHANICAL PENETRATIONS, SEE 1- 4/S3.04. Date 12/30/2022 Lic. No. P27101
8
10. SEE TYPICAL COLUMN TO BEAM CONNECTIONS 5/S3.04 , 6/S3.04 & 7/S3.04 AND SCHEDULE SHEET S4.00.
11. ALL COMPOSITE SLAB EDGES TO BE FIELS VERIFIED PRIOR TO STRUCTURE FABRICATION. Revisions
12. SEE SHEET 4/S3.04 FOR TYPICAL COMPOSE SYSTEM DETAILS.
W18X35
W18X35

W18X35
W18X35

W18X35

W18X35

Description Date Num

W18X35

W18X35
W18X35

W18X35

4,4,4,4

4,4,4,4
2 EQ SPS @ 5'-10" = 11'-8"
16
16

16
16

16

16
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

16

16

1
1

W10X17

23'-5"
TYP.
8
TYP. TYP. TYP.
15 15 11

S3.04
S3.04 S3.04 S3.04

15
7'-4" 2 EQ SPS @ 7' - 4" = 14' - 8" 7'-4" 6'-8" 2 EQ SPS @ 6' - 8" = 13' - 4" 6'-7"
28/12/2022 10:51:26

W10X17 Comm: 216050

8 Date: 12/30/2022

SEE ARCH FOR

WIDTH AND LOCATION
SEE ARCH FOR
WIDTH AND LOCATION
KEYNOTES Drawn:
Check: North
1'-7 5/8"

5'-10"

1 PROVIDE SLIP CRITICAL CONNECTION AT BEAM ENDS.

1'-4 5/8"
1 1
10"

W27X84
1
W27X84 W10X17
2 COORDINATE WITH ARCHITECTURAL DESIGN FOR HAND RAIL AND STAIR ACCESS. MAIN LEVEL
1.0
9,9,9,9 9,9,9,9 8
4 PROVIDE A DOUBLE ANGLE CONNECTION FLOOR FRAMING

2'-4"
S PLAN - AREA - 'B'
TYP.

TYP.

TYP.
9 5/8"

EXIST W16X31 TOB 99'-8" W10X22 TOB 99'-8" EXIST W16X31 TOB 99'-8"
8
S3.03

S3.03
S3.03

S3.03

S3.03

S3.07
X.1
12

12
13

13

S3.04
13

16

EXIST 20KSP

TOB 99'-8" 16KSP TOB 99'-8"

COMP. DECK 22

EXIST W16X31

EXIST W18X50
GA. W/ 4" THICK

EXIST 36" DEEP

EXIST 36" DEEP

TRUSS GIRDER
TRUSS GIRDER

TOB 99'-5 1/2"

TOB 99'-5 1/2"

TOB 99'-5 1/2"

TOB 99'-5 1/2"

EXIST 1 1/2"

CONC.

Scale: As indicated

EXIST 20KSP 16KSP TOB 99'-8"

5'-7 1/2"
PERMIT SET
S2.01b
TOB 99'-8"

X.C X.B X.A.4 X.A

NOT FOR CONSTRUCTION
 Winneshiek
Expansion and
7.68 F.96 6.68 D.22 C.22 B.22 A.22
Renovation
11" 1'-1" 21'-2 1/4" 31'-3" 26'-9" 9'-3" 11"
901 Montgomery St
Decorah, IA 52101

216051

30" x 14 1/2"

EXISTING 21" x 14 1/2"

EXISTING 30" x 14 1/2"

EXISTING 30" x 14 1/2"

31'-5 1/2" 17'-6" 20'-6"

Winneshiek Medical
Center
Decorah, IA 52101

IA EXISTING 3" SLAB REINF W6X6-6X6

W.W.M TYP SEE B.S 8/35
EXISTING FFE= 100' - 0"

INDICATES
PROFILE SECTION (u): INDICATES
POSITIVE BEAM
20'-1"

CAMBER IN INCHES

EXISTING 30" x 14 1/2"

EXISTING 21" x 14 1/2"

W AXB (u)

EXISTING 30" x 14 1/2"

EXISTING 30" x 14 1/2"

n
INDICATES
NO OF 3/4" Ø x 3"
HEADED STUDS;
SEE 10/S3.04

6'-8" 24'-7"
TAG BEAM LEGEND H

S3.04
S3.03

14
13
28 1/2" x 13 EXISTING 28 1/2" x 13 EXISTING 28 1/2" x 13 1 3/4"
G.96

TYP.
TYP.
9'-4 3/4"

7 3/4"
5

7 3/4"
S3.05
SIM.
W24X62 W24X62 W16X26
4.22 30 24 8
4.22
4 5/8"

1.96. W16X31 EXISTING

4 4 5
SIM.

S3.05 S3.05 S3.05

5'-7"
7'-3"

4'-0"

14

7'-11 1/8"
EXISTING W18X55

S3.04
TYP.
11'-3 3/8"

2'-9 5/8" 2'-10 1/8"

W16X26

W16X26 EXISTING W16X26

W14X22
12

12 8
2.96.
4'-0"

4"
W14X22 W14X22
S3.03
EXISTING W16X31

5'-7"
5

W16X26 EXISTING

W14X22

W14X22
4" C 2022 Quetica Professional Engineers, Inc.

3'-7 1/4"
4" All rights reserved.

S3.04

S3.04
This document is an instrument of service and is the property of

22
EP1 EP1

16
Quetica Professional Engineers, Inc. and may not be used or copied
without prior written consent.
W18X35
4'-0"

8 MAIN LEVEL FLOOR PLAN - AREA 'H'

W14X22
1

4"
W14X22 W14X22
1/4" = 1'-0"
27'-4 1/4"

W16X26

W16X26

W16X26

W16X26

W16X26

28'-0"
W16X26 EXISTING

W16X26

W16X26

W16X26
0

4"
5'-9 1/2"

16
16

5'-7"
16
16

16
16

16
5 5'-11 1/8".

16
UNLESS NOTED OTHERWISE:
8" 6'-0" 8" S3.03

W21X44
4'-0"
EXISTING W18X55
18'-0"

TYP. 1. SEE SHEET S0-00 FOR STRUCTURAL NOTES, ABBREVIATIONS AND SYMBOLS.

24
12 2. SEE SHEET S4.00 FOR SCHEDULES

W21X44
0,2,5,5
S3.04 W14X22 3. TOP OF SLAB ELEVATION = 100'-0" UNLESS OTHERWISE NOTICED
W16X26 EXISTING 8 4. 2" - 20GA. COMPOSITE DECK W/ 4" NORMAL WEIGHT CONCRETE (6" TOTAL THICKNESS) UNLESS
1 OTHERWISE NOTICED. REINFORCE W/ SYNTHETIC MACRO FIBER REINFORCING ACCORDING TO THE
EP1 EP1 S3.05 SPECIFICATIONS.
EXISTING FFE= 100' - 0" 5. TYPICAL TOP OF STEEL BEAM EL. = 99'-6".
4'-0"

5'-7"

14'-11"
EXISTING 8" CORE SLAB 6. SEE STRUCTURAL NOTES FOR TYPICAL OPENING FRAMING. COORDINATE WITH ARCHITECTURAL AND
S3.03

+3" COMP. TPG TYP.

5

15 MECHANICAL DRAWINGS FOR OPENING LOCATION AND SIZE. SEE 19/S3.04 FOR DETAILS.
S3.04 2" COMPOSITE DECK W/ 4" THICK CONCRETE OVER 6 1/2" 7. SEE ARCHITECTURAL DRAWINGS FOR LOCATION OF RAMPS, SLAB SLOPES, STEPPED SLABS PARTITION
W16X26 EXISTING
10'-3 3/8"

DECK (6" TOTAL THICKNESS) WALLS AND STAIRS.

W16X26

W16X26

W14X22 TYP. 8. REFER TO ARCHITECTURAL DRAWINGS FOR ADDITIONAL INFORMATION AND DIMENSIONS.
10

10

18 9. FOR BEAMS WITH MECHANICAL PENETRATIONS, SEE 1- 4/S3.04 .

W18X35
8
4'-0"

S3.04 10. SEE TYPICAL COLUMN TO BEAM CONNECTIONS 5/S3.04 , 6/S3.04 & 7/ S3.04 AND SCHEDULE SHEET S4.00.

16
11. ALL COMPOSITE SLAB EDGES TO BE FIELS VERIFIED PRIOR TO STRUCTURE FABRICATION.
S3.04

S3.04

5'-0 1/4"
12

12
12. SEE SHEET S3.04 FOR TYPICAL COMPOSITE SYSTEM DETAILS.
6.96. W16X26 EXISTING
TYP.

TYP.
EXISTING W16X26

W24X94 W24X94 W14X22

4'-0"

S3.04
3.22 3.22

16
30 26 8

3'-0"

3'-0"
W16X26 EXISTING 8"

4"
W18X35
8 KEYNOTES
4'-0"

12
TYP.

S3.04
S3.03
12
AB

15

5'-6 1/2"
S3.04 1 PROVIDE SLIP CRITICAL CONNECTION AT BEAM ENDS.
W16X26 EXISTING 14
13'-11 1/2"

13'-11 1/2"
S3.04

TYP.
TYP.
COORDINATE WITH ARCHITECTURAL DESIGN FOR HAND RAIL AND STAIR ACCESS. CD

W21X44
2

5,5,0

10'-11 1/2"
4'-0"

6'-7" 6'-2" 6'-2" 6'-2" 6'-2" 5'-4" 5'-4" 5'-4" 5'-4" 5'-5"
4 PROVIDE A DOUBLE ANGLE CONNECTION
E F
24'-0"
EXISTING W24X84

8
4"

W16X26 EXISTING W14X22 W14X22

W16X26
G H
W21X44

W16X26

W16X26

W16X26

W16X26

W16X26

W16X26

W16X26

W21X44
W16X26

W14X22

22

S3.03
1'-2 5/8" 2'-6 3/8"

5'-5"
16

16

16

16

16

16

16

16

16

16

16
W14X22

5
S3.04
4"
4'-0"

4" TYP.
11 EP2 4"
EP2

4"
4"

W16X26 EXISTING W14X22 W14X22 S3.04

2.22 2.22

8"
KEY PLAN

8"
8"
4'-0"

4'-3 3/4"
1'-11 3/4" TYP. I hereby certify that this plan, specifcation or report was
15
prepared by me or under my direct supervision and that I
W16X26 EXISTING S3.04
8'-4"

8'-4"
am a duly Licsened Professional Engineer under the laws

7'-10 3/4"

7'-8"
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

of the state of Minnesota.

4'-0"

8" 8" 11"

EP2 8'-4 1/2" Katherine Russell
5
12.96 W16X26 EXISTING
W24X62 W24X62
S3.03 Date 12/30/2022 Lic. No. P27101

1.22 1.22

10 3/4"
30 24
Revisions
7 1/8"
4'-0"

EXISTING W16X31

Description Date Num

1'-2 5/8"

8"
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

EXISTING W24X84
9'-0"

W16X26 EXISTING
S3.04
S3.04

20
20
4'-4 3/8"

9" 5'-3 3/4" 25'-11 1/4"

W16X31 EXISTING
9"

13.96
28/12/2022 10:51:27

1'-8" 20'-10" 1'-5 1/4" 31'-3" 26'-9" 9'-3" 11"

Comm: 216050
Date: 12/30/2022
F.96 G.96 Drawn:
Check: North

MAIN LEVEL
FLOOR FRAMING
S PLAN - AREA 'H'

Scale: As indicated

PERMIT SET
NOT FOR CONSTRUCTION S2.01h
 Winneshiek
Expansion and
Renovation

901 Montgomery St
Decorah, IA 52101

216051
Winneshiek Medical
Center
E.4 D.99 D.2 B.9 A.9 A.1 1.91 Decorah, IA 52101
11'-4" 23'-6" 28'-6" 29'-4" 26'-7" 8'-8"

IA E.6

S3.06
6

S3.06
1

S3.06
S3.06

S3.06

2
S3.07

1'-1 1/4"

2
2

2
@BRACE
TYP.
1 1 1 1 1
W18X35 W18X35 W18X35 W18X35 W18X35 W18X35 1

5.0
1
TYP.
* * * *
S3.06
1
S3.06
TYP.

1
1

TOB 114'-6 1/2"

TOB 114'-6 1/2"
6 1/2"

TOB 114'-6 1/2"

TOB 114'-6 1/2"

TOB 114'-6 1/2"

TOB 114'-6 1/2"
TOB 114'- 5

W18X35

W18X35

W18X35

W18X35

W18X35
W21X44
W 18X3

16K5

16K5

16K5

16K5

16K5

16K5

16K5

16K5
16K5

16K5

16K5

16K5

16K5

16K5

16K5
17'-8"

16K5

16K5
16K5

16K5

16K5

16K5
2 3
S3.07 S3.07

16K5
3'-6 1/8" 5'-0" 5'-0" 4'-8 3/8" 3 EQ SPS @ 4'-8 3/8"= 9'-4 3/4" 4'-8 3/8" 4'-9" 4 EQ SPS @ 4'-9" = 19'-0" 4'-9" 4'-10" 4 EQ SPS @ 4'-11" = 19'-8" 4'-10" 4'-5" 4 EQ SPS @ 4' - 11" = 19' - 8" 4'-5" 4'-4" 4'-4"

S3.06
12
SINGLE PLATE 11"
CONNECTION

TYP.
W21X44 W21X44 W21X44 W21X44

*
W21X44
4.0 * * *

2'-4"
8 3/4"
9 W18X35
S3.04 TYP.
12

1
TYP. 1-1/2" 20GA. TYPE B ROOF DECK S3.06 1'-0 3/4" 3.9
S3.06
4 EQ SPS @ 4'-9" = 19'-0" 4 EQ SPS @ 4' - 11" = 19' - 7" 1

TOB 114'-6 1/2"

4'-9" 4'-9" 4'-11" 4'-11"
S3.06
TYP.

W18X35
1
6 1/2"

16KSP (400/100)

16KSP (400/100)

16KSP (400/100)

16KSP (400/100)

16KSP (400/100)
TOB 114'- 5

1
W 18X3

1
S

16KSP (180/45)
16K5

16K5

5 W: INDICATES LENGTH OF

16KSP (400/100)

16KSP (400/100)

16KSP (400/100)

16KSP (400/100)
16KSP (300/75)

16KSP (200/50)

16KSP (200/50)

16KSP (180/45)

16KSP (200/50)

16KSP (200/50)

16KSP (300/75)
TOB 114'-6 1/2"

16KSP (400/100)

TOB 114'-6 1/2"

TOB 114'-6 1/2"

TOB 114'-6 1/2"

TOB 114'-6 1/2"

S3.06 ADDED SNOW LOAD.
W18X35

W18X35

W18X35

W18X35

W18X35
24'-11"

16KSP

16KSP
* * * * * * *
L4x3x3/8" L4x3x3/8" L4x3x3/8" L4x3x3/8" C 2022 Quetica Professional Engineers, Inc.
16K5

L4x3x3/8" L4x3x3/8" L4x3x3/8"

16K5
16K5

16K5
JOIST HEADER S: INDICATES ADDED SNOW All rights reserved.
DRIFT LOADING TO FLAT This document is an instrument of service and is the property of
BY SUPPLIER
Pdrift ROOF LOADING.
Quetica Professional Engineers, Inc. and may not be used or copied
without prior written consent.
448lb DL + 298lb LL + 448lb S
Pf Pf: FLAT ROOF LOADING
5 ACCORDING ASCE 7-16.
5 5 5 5 5 S3.06
S3.06 S3.06 W
S3.06 S3.06 S3.06
12K5

1'-4" 4'-11 3/4" 5'-0" 5'-0" 4'-4" 4'-4"

8'-1"
38 PSF TAG SNOW LOADING
S3.06

S3.05
15

3
TYP. 4

TYP.
W18X35 S3.07
3.1

6"
1 3 1 3 W21X44 W18X35
1 1
2'-1"

1 TOB 114'-4" TOB 114'-4"

W21X44
3.0
1
S3.06
TYP.
* W21X101
10,10,10,10
W21X101
10,10,10,10
* INDICATES
PROFILE SECTION (u): INDICATES
POSITIVE BEAM
CAMBER IN INCHES
1-1/2" 20GA. TYPE B ROOF DECK TYP. 1-1/2" 20GA. TYPE B ROOF DECK
1

15 W AXB (u)
TOB 114'-6 1/2"
6 1/2"

S3.04
12K5

4'-0" 5'-0" 5'-0" 2'-6" 2'-6" 2'-6" 2'-0" 0" 2'-6" 2'-6" 2'-6" 5'-0" 5'-0" 5'-0" 4'-4" 8'-8" 4'-4"
1
TOB 114'-6 1/2"
TOB 114'-X35

W18X35

W18X35 TOB 114'-4"

TOB 114'-4"
12K5

12K5

W18X35 TOB 114'-4"

W18X35

5
W 18

TOS 114'-8 1/2" 2'-0 1/2" 2'-0 1/2"

4
INDICATES
15'-5"

S3.07
2'-0 1/2"
NO OF 3/4" Ø x 3"
16KSP (180/45)

1
HEADED STUDS;

1
16KSP (300/75)

16KSP (200/50)

16KSP (200/50)

16KSP (180/45)

16KSP (200/50)

16KSP (200/50)

16KSP (300/75)

TOB 114'-6 1/2"

SEE 10/S3.04
2

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35

W18X35
16KSP

* *
7 L4x3x3/8" L4x3x3/8"
23'-3"

16K5

16

16

16

16

16

16

16
16

16
S3.07
TAG BEAM LEGEND
1'-3 1/2"

16K5
16KSP

16K5

16K5

TOB 114'-6 1/2"

TYP.
W18X35

W18X35
2 2
2.3 53 PSF
S3.05 2" COMPOSITE DECK 20 GA. W/ 4 1/2" THICK CONCRETE
(TOTAL)
S3.05
TYP. 53 PSF
1
S3.06
TYP.
3'-5 7/8" 5'-0" 4'-8 7/8" 2'-7 1/2"2'-7 3/8"
AB
KEYNOTES
7'-10"

S3.04
7

12
1
TYP. S3.05
CD
S3.06

TYP.
S3.06
2

E.6 1
W21X44
11'-5" 1 1 11'-5"
W21X44
1
W21X44 1
1 PROVIDE SLIP CRITICAL CONNECTION AT BEAM ENDS.

2.0 1'-4 1/2" * 8"

TYP.
7'-1 1/2"
W21X44
5,5,5,5
2 EQ SPS @ 7'-1 1/2" = 14'-3" 7'-1 1/2" 7'-4"
W21X44
5, 5, 5, 5
2 EQ SPS @ 7'-4" = 14'-8" 7'-4" 8" * 5
SIM.
2 BEAM ALIGNED WITH ELEVATOR CENTERLINE. E F
G H
2
S3.05 3 SEE BEAM TO BEAM CONNECTION IN DETAIL 17/S3.04.
2
7'-5"

W10X17

W10X17

W10X17

W10X17

W10X17

W10X17
EXIST W12X19 S3.05 S3.05
1.07 TYP.
8

8
TOB 113'-7 1/2" 4 SEE BEAM TO COLUMN CONNECTION IN DETAIL 7/S3.05 .
11 3/4" SC9 SC9 SC9 1
1

4
W21X101 W21X101 S3.06
1.10 10,10,10,10 10,10,10,10
TYP. KEY PLAN
TOB 114'-6 1/2"

1
EXIST W14X22

TYP.

TYP.
TOB 113'-10"

1
3
TYP.

TYP.
TYP.
TOB 113'-10"

6"

TOB 114'-4"
TOB 113'-10"
EXIST 14K3

EXIST 14K3

W21X44

TOB 114'-6 1/2"

* L4x3x3/8" I hereby certify that this plan, specifcation or report was
TOB 114'-4"
0, 6 TOB 114'-4"

S3.04

S3.04
1-1/2" 20GA. TYPE B ROOF DECK

W18X35
S3.06

53 PSF
S3.05

* *
L4x3x3/8" L4x3x3/8"
S3.04

prepared by me or under my direct supervision and that I

8
23'-5"

8
15

3
8

LOW ROOF & PENTHOUSE FLOOR FRAMING PLAN - AREA 'A' & 'B' am a duly Licsened Professional Engineer under the laws
16KSP (180/45)

6
1
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

S3.07 of the state of Minnesota.

TOB 114'-6 1/2"

3/16" = 1'-0"
13'-11 1/8"

11'-4"
16KSP (300/75)

16KSP (200/50)

16KSP (200/50)

16KSP (180/45)

16KSP (200/50)

16KSP (200/50)

16KSP (300/75)
12KSP (400/100)

12KSP (400/100)

12KSP (400/100)
12KSP (400/100)

12KSP (400/100)

12KSP (400/100)

12KSP (400/100)

12KSP (400/100)

12KSP (400/100)

12KSP (400/100)
0

W18X35
W27X84

16
W27X84

W27X84
16KSP

UNLESS NOTED OTHERWISE:

16KSP

16K5

16K5
16K5
16K5

S3.06
0, 6

0, 6
Katherine Russell
1. SEE SHEET S0.0 0FOR STRUCTURAL NOTES, ABREVIATIONS AND SYMBOLS. Date 12/30/2022 Lic. No. P27101
EXIST 1'-1/2" 22 2. SEE SHEET S4.00 FOR SCHEDULES.
7 7 7
S3.04

GA. TYPE B ROOF 3. TYPICAL JOIST BEARING/TOP STEEL BEAM EL.= 114'-4" SEE PLAN.
S3.03 S3.03 S3.03
9

DECK TYP. 4. SEE WIND, SNOW AND SEISMIC LOADS AT S0.00. Revisions
4'-0" 5'-0" 5'-0" 2'-6" 2'-6" 2'-6" 2'-0" 4'-9" 4 EQ SPS @ 4'-9" = 18'-11 7/8" 4'-9" 4'-11" 4 EQ SPS @ 4' - 11" = 19' - 7" 4'-11" 2'-6" 2'-6" 2'-6" 5'-0" 5'-0" 5'-0" 4'-4" 4'-4" 5. SEE 8/S3.06 FOR TYPICAL ROOF OPENING FRAMING AND 19/S3.04 FOR Description Date Num
FLOOR OPENING FRAMING. COORDINATE WITH
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

1'-4 3/4"
1.112 ARCHITECTURAL/MECHANICAL DRAWINGS FOR OPENING LOCATION AND
8 3/4"

1 1 1 2'-0 1/2" 2'-0 1/2" 1 SIZE.

W18X35 W18X35 W18X35 1
1.0 EXIST W12X30
TOB 113'-7 1/2" * * *
W18X35

*
W18X35 6. JOIST SUPPLIER TO DESIGN JOISTS FOR:
- TOTAL LOAD/LIVE LOAD NOTED IN JOIST DESIGNATION.
- SNOW DRIFT LOADS SHOWN ON PLAN.
2'-0 7/8"

2.07 X.1 - LOADS SHOWN ON DETAILS.

TYP.
TYP.

TYP.
TYP.

EXIST W16X31 EXIST W10X22 EXIST W10X22 - WIND LOADS, SEE S0.00
EXIST W16X31 EXIST W10X22
TOB 112'-4" TOB 112'-4" TOB 112'-4" 8
TOB 112'-4" TOB 112'-4" 7. REFER TO ARCHITECTURAL DRAWINGS FOR ADDITIONAL INFORMATION AND

S3.06
S3.06

S3.07
S3.06

S3.06
S3.06

DIMENSIONS.

13
13

13
13

2
8. SEE 6/S4.00 FOR TYPICAL DECK ATTACHMENT TO JOISTS.
9. PROVIDE 2-5/16" WEB STIFFENER PLATES AT STEEL BEAMS RUNNING OVER
EXIST 18K6 EXIST 12K5 EXIST 18K6 EXIST 18K6
EXIST W12X19

COLUMNS OR WALLS CENTER ON SUPPORT.

GA. TYPE B ROOF
28/12/2022 10:51:30

TOB 113'-10"

EXIST 36" DEEP

TOB 113'-10"

TRUSS GIRDER

EXIST 36" DEEP

TRUSS GIRDER
10. SHADED AREA INDICATES: 2" - 20GA. COMPOSITE DECK W/ 2 1/2" NORMAL
EXIST 36" DEEP

TOB 112'-1 1/2"

EXIST 36" DEEP

TRUSS GIRDER
TRUSS GIRDER
TOB 113'-10"

TOB 112'-1 1/2"

TOB 112'-1 1/2"

TOB 112'-4"
EXIST 14K3

EXIST 14K3

TOB 112'-4" TOB 112'-4"

EXIST 36" DEEP
TRUSS GIRDER

TOB 112'-4"
EXIST 1'-1/2" 22
TOB 112'-1 1/2"

TOB 112'-1 1/2"

WEIGHT CONCRETE (4 1/2" TOTAL THICKNESS) UNLESS OTHERWISE Comm: 216050

NOTICED. REINFORCE W/ SYNTHETIC MACRO FIBER REINFORCING
Date: 12/30/2022
ACCORDING TO THE SPECIFICATIONS.
11. ROOF BEAM BOTTOM FLANGE TO BE BRACED ACCORDING TO PLAN VIEW (*) Drawn:
DECK.

EXIST 18K6 EXIST 12K5 EXIST 18K6 EXIST 18K6 AND DETAIL 5/S3.06 AND 6/S3.06 .
Check: North
12. TOP OF SLAB ELEVATION= 114'-8".
TOB 112'-4" TOB 112'-4" TOB 112'-4" TOB 112'-4"
13. SEE SHEET S3.04 FOR TYPICAL COMPOSITE SYSTEM DETAILS.

LOW ROOF &

PENTHOUSE
F.07 X.E X.D X.C X.B X.A.4 X.A
S FLOOR FRAMING
PLAN AREA 'A' &
'B'
Scale: As indicated

PERMIT SET
NOT FOR CONSTRUCTION S2.02a
 Winneshiek
Expansion and
Renovation

901 Montgomery St
Decorah, IA 52101

216051
Winneshiek Medical
Center
Decorah, IA 52101

7.68 F.96 6.68 D.22 C.22 B.22 A.22

IA 31'-3" 26'-9" 10'-2"

S W: INDICATES LENGTH OF
ADDED SNOW LOAD.
S: INDICATES ADDED SNOW
DRIFT LOADING TO FLAT
Pdrift ROOF LOADING.

Pf Pf: FLAT ROOF LOADING

8" 6'-8" 24'-7" 26'-9" 9'-3" 11" ACCORDING ASCE 7-16.
W

S3.03

S3.03
9
G.96

4
9'-7 3/4"
5 TAG SNOW LOADING.

1'-1 3/4"
S3.05
SIM.
4.22 W21X44

W18X55 EXISTING
W21X62 W21X44
1.96. W16X31 EXISTING

4'-8"
W16X31EXISTING
7
INDICATES
7 1-1/2" 18GA. TYPE B ROOF DECK PROFILE SECTION (u): INDICATES

W14X22
S3.05

W14X22

W14X22
W24X94
5'-9"

12 S3.05 POSITIVE BEAM

W14X22

W14X22

W14X22

W14X22

W14X22
9'-3 3/4"

S3.03

8'-11"

8'-11"
W14X22 CAMBER IN INCHES
W16X26 EXISTING 10

S3.03
10

S3.04

S3.03
8 W AXB (u)

18
8
S3.03

8
S3.03 9
42 PSF
2.96.

4'-8"
42 PSF S3.03
n

TYP.

17'-2 1/4"
3"
W16X26 EXISTING SC19 SC19 SC19 INDICATES
W24X62 W24X62 W14X22
1'-11 5/8"

NO OF 3/4" Ø x 3"
EP2 EP1 30 26 8 HEADED STUDS;

W16X26
SEE 10/S3.04

4'-8"
10'-7"

60 PSF 3'-0" 3'-0" 60 PSF

W18X55 EXISTING
27'-4 1/4"

W24X94
W16X26 EXISTING
5'-9 1/2"

C 2022 Quetica Professional Engineers, Inc.

W8X28
W14X22 All rights reserved.
14 This document is an instrument of service and is the property of
8
S3.03 TAG BEAM LEGEND. Quetica Professional Engineers, Inc. and may not be used or copied
without prior written consent.

4'-8"
S3.08
W16X26 EXISTING
4.96

W16X26

W16X26

W16X26

W16X26

W16X26

W16X26

W16X26
4

W24X94
W30X99
W14X22

16,0
16,0

16

16

16

16
16

16

16

1-1/2" 18GA. TYPE B ROOF DECK

EXISTING FFE= 100' - 0"
EXISTING 8" CORE SLAB
+3" COMP. TPG
EP1 EP1

8
8 KEYNOTES
7'-5"

4'-8"
S3.03
10'-3 3/8"

S3.03

2
W16X26

W16X26
PROVIDE SLIP CRITICAL CONNECTION AT BEAM ENDS.

10'-2"
W16X26 EXISTING 1

10

10
W14X22

S3.04
W16X26 EXISTING
8

12
8 2 BEAM ALIGNED WITH ELEVATOR EXIT TO BE FIELD VERIFIED.

4'-0 1/4"
6.96. 12
S3.03 S3.03 TYP.

TYP.
W16X26 EXISTING 2" COMPOSITE DECK W/ 4" CONCRETE (6" TOTAL THICKNESS) 1
S3.06
W24X94 W24X94 W14X22
3.22 30 26 8
8'-11"

W24X94

4'-7"
LOWER ROOF &PENTHOUSE FLOOR FRAME PLAN

0,12
W16X26 EXISTING
1 3/16" = 1'-0"
8" 6'-7" 6'-2" 6'-2" 6'-2" 6'-2 1/8" 5'-4". 5'-4" 5'-4" 5'-4" 5'-5" W14X22 0

W24X94
W24X94

W16X26

W27X94

12'-10 1/2"
8

W16X26

W16X26

W16X26

W16X26
W16X26

W16X26

W16X26
0,12

0,12
13'-11 1/2"

13'-11 1/2"
W24X84 EXISTING

12

12

12

12

12

12

12

12

4'-7"
W16X26 EXISTING
9
10 S3.03 UNLESS NOTED OTHERWISE:

S3.04
S3.03 10
24'-0"

8
S3.03 W14X22 1. SEE SHEET S0.0 0 FOR STRUCTURAL NOTES, ABREVIATIONS AND SYMBOLS.
8 2. SEE SHEET S4.00 FOR SCHEDULES.
60 PSF

TYP.
W16X26 EXISTING 60 PSF 3. TOP OF SLAB ELEVATION= 114' 6"

5'-5 5/8"
SC19 SC19 4. SHADED AREA INDICATES 2" - 20GA COMPOSITE DECK WITH 4" NORMAL
W24X62 SC19

S3.03
W24X62 EP2 WEIGHT CONCRETE (6" TOTAL THICKNESS)

1'-1"
30 26 5. TYPICAL TOP OF BEAM ELEVATION= 114' 0"
2.22 6. SEE STRUCTURAL NOTES FOR TYPICAL OPENING FRAMES. COORDINATE

0"

8"
W16X26 EXISTING

S3.03
WITH ARCHITECTURAL AND MECHANICAL DRAWING LOCATIONS. SEE
S3.03

1-1/2" 18GA. TYPE B ROOF DECK EP2

8
42 PSF 19/S3.04.
8

42 PSF

3'-11"
7. SEE WIND, SNOW AND SEISMIC LOADS AT S0.00.

8'-5 1/4"

8'-5 1/4"
8" 8"
AB

W14X22

W14X22
11"

W14X22

W14X22
8. SEE 8/S3.06 FOR TYPICAL ROOF OPENING FRAMING. COORDINATE WITH
8'-4 1/2"
W14X22

W14X22
8'-4"

8'-4"
W14X22

W14X22
ARCHITECTURAL/MECHANICAL DRAWINGS FOR OPENING LOCATION AND

7'-8"
W16X26 EXISTING 12
S3.03 W8X28 9.
SIZE.
JOIST SUPPLIER TO DESIGN JOISTS FOR:
CD

3'-11 3/4"
EP2
3 - TOTAL LOAD/LIVE LOAD NOTED IN JOIST DESIGNATION.
W16X31 EXISTING

12.96 W21X44 W21X44

S3.03 - SNOW DRIFT LOADS SHOWN ON PLAN.

10 3/4"
E F
W24X84 EXISTING

- LOADS SHOWN ON DETAILS.

1.22 W16X26 EXISTING 10. REFER TO ARCHITECTURAL DRAWINGS FOR ADDITIONAL INFORMATION AND
6 7/8"

DIMENSIONS.
11.
12.
SEE FOR TYPICAL DECK ATTACHMENT TO JOISTS.
PROVIDE 2-5/16" WEB STIFFENER PLATES AT STEEL BEAMS RUNNING OVER
G H
9'-9"

COLUMNS OR WALLS CENTER ON SUPPORT.

W16X26 EXISTING

S3.04
13. SHADED AREA INDICATES: 2" - 20GA. COMPOSITE DECK W/ 2 1/2" NORMAL

21
WEIGHT CONCRETE (4 1/2" TOTAL THICKNESS) UNLESS OTHERWISE
9" NOTICED. REINFORCE W/ SYNTHETIC MACRO FIBER REINFORCING
ACCORDING TO THE SPECIFICATIONS.
W16X31 EXISTING 14. ROOF BEAM BOTTOM FLANGE TO BE BRACED ACCORDING TO PLAN VIEW (*) KEY PLAN
13.96 15.
AND DETAIL
SEE TYPICAL COLUMN TO BEAM CONNECTIONS 5-7/S3.04 AND SCHEDULE
SHEET S4.00 I hereby certify that this plan, specifcation or report was
16. SEE SHEET S3.04 FOR TYPICAL COMPOSITE SYSTEM DETAILS. . prepared by me or under my direct supervision and that I
am a duly Licsened Professional Engineer under the laws
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

of the state of Minnesota.

Katherine Russell
Date 12/30/2022 Lic. No. P27101

Revisions
Description Date Num
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

28/12/2022 10:51:31

Comm: 216050
Date: 12/30/2022
Drawn:
Check: North

LOW ROOF &

PENTHOUSE
S FLOOR FRAMING
PLAN AREA 'H'

Scale: As indicated

PERMIT SET
NOT FOR CONSTRUCTION S2.02h
 Winneshiek
Expansion and
Renovation

901 Montgomery St
Decorah, IA 52101

216051
Winneshiek Medical
D.2 B.9 A.9 Center

TOB 131'-10 1/2"

28'-6" 29'-4"
Decorah, IA 52101

TOB 131'-10 1/2"

TOB 131'-10 1/2"

S3.06
S3.06
S3.06

6
4

2
6
S3.06
S3.07

IA

@BRACE
@BRACE
5 3/4"

TYP.
W21X44 W21X44

TYP.
1 1
TOB 131'-8" TOB 131'-8"
3.0 * *

SIM.
SIM.
SIM.

S3.05
S3.05

5
5
S3.05
5
7 3/4" 7 3/4"
4'-3" 4 EQ SPS @ 5'-0" = 20'-0" 4'-3" 4'-8" 4 EQ SPS @ 5'-0" = 20'-0" 4'-8"

W21X44 SLOPES
5
S3.06 5

W21X44 SLOPES
S3.06

W21X44 SLOPES
23'-3"

SLOPE 1/4" / 1' - 0"

1
L4x3x3/8 L4x3x3/8 L4x3x3/8

* 5 * *

31'-7 3/4"
S3.06
30'-8"

18K7

18K7

18K7

18K7
18K7

18K7

18K7

18K7

18K7

18K7
1
3
S3.06
3
S3.06
TOB 132'-4 1/2"
1-1/2" 20GA. TYPE B ROOF DECK
S3.05

10
8

S3.05
S3.06

8
TOB 132'-4 1/2"

2.0 KEYNOTES
TOB 132'-5" C 2022 Quetica Professional Engineers, Inc.

W21X44 SLOPES
All rights reserved.
PROVIDE SLIP CRITICAL CONNECTION AT MAIN BEAMS ENDS.
W21X44 SLOPES

1 This document is an instrument of service and is the property of

TOB 132'-5" Quetica Professional Engineers, Inc. and may not be used or copied
without prior written consent.
7'-5"

1
1

S3.05
S3.05

S3.05
S3.06

S3.06

5
5

5
2

2
W21X44 W21X44

SIM.
SIM.

1 1

SIM.
TOB 132'-4" TOB 132'-4" PENTHOUSE ROOF LEVEL FLOOR PLAN - AREA 'A' & 'B'
1.10
* * 1 1/4" = 1'-0"
0

@BRACE
SC4
5 3/4"

TYP.
6
TOB 132'-6 1/2" TOB 132'-6 1/2" S3.07 TOB 132'-6 1/2"

S3.06
UNLESS NOTED OTHERWISE:

6
1. SEE SHEET S0.00 FOR STRUCTURAL NOTES, ABREVIATIONS AND SYMBOLS.
59'-1 3/4"
2. SEE SHEET S4.00 FOR SCHEDULES.
3. JOIST BEARING ELEVATION VARIES. SEE PLAN.
4. SEE WIND, SNOW AND SEISMIC LOADS AT S0.00.
5. SEE 8/S3.06 FOR TYPICAL ROOF OPENING FRAMING. COORDINATE WITH
ARCHITECTURAL/MECHANICAL DRAWINGS FOR OPENING LOCATION AND
SIZE.
6. JOIST SUPPLIER TO DESIGN JOISTS FOR:
- TOTAL LOAD/LIVE LOAD NOTED IN JOIST DESIGNATION.
- SNOW DRIFT LOADS SHOWN ON PLAN.
- LOADS SHOWN ON DETAILS.
- WIND LOADS, SEE S0.00
7. REFER TO ARCHITECTURAL DRAWINGS FOR ADDITIONAL INFORMATION AND
DIMENSIONS.
8. ROOF GIRDER BOTTOM FLANGE TO BE BRACED ACCORDING TO PLAN VIEW
(*) AND DETAILS 5/S3.06 & 6/S3.06.
9. SEE 6/S4.00 FOR TYPICAL DECK ATTACHMENT TO JOISTS AND PERIMETER
BEAMS/ANGLES.
10. COORDINATE ALL OPENINGS THROUGH ROOF AND WALLS WITH
ARCH/MECH.

AB
CD

E F
G H

KEY PLAN
I hereby certify that this plan, specifcation or report was
prepared by me or under my direct supervision and that I
am a duly Licsened Professional Engineer under the laws
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

of the state of Minnesota.

Katherine Russell
Date 12/30/2022 Lic. No. P27101

Revisions
Description Date Num
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

28/12/2022 10:51:32

Comm: 216050
Date: 12/30/2022
Drawn:
Check: North

PENTHOUSE
ROOF FRAMING
S PLAN - AREA 'A' &
'B'

Scale: As indicated

PERMIT SET
NOT FOR CONSTRUCTION S2.03a
 Winneshiek
Expansion and
Renovation

901 Montgomery St
Decorah, IA 52101

216051
Winneshiek Medical
Center
Decorah, IA 52101

IA

D.22 31'-3" C.22 26'-9" B.22

4.22
1
S3.08
3"

S3.06

S3.06
2

@BRACE
C 2022 Quetica Professional Engineers, Inc.
10 1/4"

10 1/4"
All rights reserved.

TYP.
This document is an instrument of service and is the property of
W21X44

* *
TOB =127’- 0” W21X44 Quetica Professional Engineers, Inc. and may not be used or copied
without prior written consent.

TOB =127’- 0” TOB 127’- 2 1/4”

TOB 127’- 2 1/4”
27'-4 1/4"

5
S3.06
KEYNOTES

SLOPES
SLOPES
S3.08
18'-0 1/2"

18'-0 1/2"
4

5 5 5 5
L4x3x3/8 ROOF JOISTS TO BE DESIGNED FOR 720 LB POINT LOAD AT CHANNELS SUPPORTING

* *
L4x3x3/8 5
MECHANICAL UNITS. COORDINATE UNIT LOCATIONS WITH MECHANICAL.

W18X35
W18X35

PROVIDE MC6X12 TOES DOWN OVER DECK FLUTES TO SUPPORT EACH SIDE OF RTU ROOF
6 CURB. WELD EACH TOE TO CROSSING JOISTS W/ 3/16"x2" MIN FILLET WELDS. EXTEND
5 3 CHANNEL 6” BEYOND CENTERLINE OF FIRST JOIST BEYOND UNITS.
S3.06 CU-1 S3.06
6 WT 4,200 LBS
L4x3x3/8 L4x3x3/8
TOB =127’-5 1/2”

18KSP 250/135

18KSP 250/135

18KSP 250/135
SLOPE 1/4" / 1' - 0"

SLOPE 1/4" / 1' - 0"

18K7 250/135
TOB =127’-5 1/2”

3.22
18K7

18K7

18K7

18K7

18K7

18K7

W18X35 SLOPES 18K7

18K7
18K7
TOB =127’-5 1/2” 5 5 5 5
TOB =127’-5 1/2”
PENTHOUSE ROOF LEVEL FLOOR PLAN - AREA 'H'
W18X35 SLOPES

1 3/16" = 1'-0"

S3.08
3
0
1-1/2" 20GA. TYPE B ROOF DECK
13'-11 1/2"

13'-11 1/2"
12'-10"

8"
4'-6 1/8" 4'-6" 4'-6" 4'-6" 4'-5" 4'-5" 8'-10" 4'-5" 4'-5" 4'-6" 4'-6" 4'-6 1/4"
UNLESS NOTED OTHERWISE:
TOB 127’-10”
1. SEE SHEET S0.00 FOR STRUCTURAL NOTES, ABREVIATIONS AND SYMBOLS.
TOB 127’-10” 2. SEE SHEET S4.00 FOR SCHEDULES.
AB
3 1/4"

3. TYPICAL JOIST BEARING/TOP STEEL BEAM EL.VARIES SEE PLAN.

W21X44 TOB =127’-8 1/2” TOB =127’-8 1/2”

*
W21X44

* 4. SEE WIND, SNOW AND SEISMIC LOADS AT S0.00.

10 1/4"

5. SEE 8/S3.06 FOR TYPICAL ROOF OPENING FRAMING. COORDINATE WITH CD

3 1/4"

@BRACE

2.22 ARCHITECTURAL/MECHANICAL DRAWINGS FOR OPENING LOCATION AND

SIZE.
TYP.

S3.06
6. JOIST SUPPLIER TO DESIGN JOISTS FOR:
E F

2
- TOTAL LOAD/LIVE LOAD NOTED IN JOIST DESIGNATION.
S3.06

2 - MECHANICAL POINT LOADS AND SNOW DRIFT LOADS SHOWN ON PLAN.

6
8'-4"

8'-4"

8'-4"
S3.08 - LOADS SHOWN ON DETAILS.
7. REFER TO ARCHITECTURAL DRAWINGS FOR ADDITIONAL INFORMATION AND G H
DIMENSIONS.
8. SEE 4/S4.00 FOR TYPICAL DECK ATTACHMENT TO JOISTS AND PERIMETER
BEAMS/ANGLES
1.22 9. PROVIDE 2-5/16" WEB STIFFENER PLATES AT STEEL BEAMS RUNNING OVER
COLUMNS OR WALLS CENTER ON SUPPORT.
10. ROOF GIRDER BOTTOM FLANGE TO BE BRACED ACCORDING TO THE PLAN
VIEW (*) AND DETAILS 5&6/S3.06
KEY PLAN
11. SEE TYPICAL COLUMN TO BEAM CONNECTIONS 5-7/S3.04 AND SCHEDULE
SHEET S4.00
12. SEE SHEET S3.04 FOR TYPICAL COMPOSITE SYSTEM DETAILS I hereby certify that this plan, specifcation or report was
prepared by me or under my direct supervision and that I
am a duly Licsened Professional Engineer under the laws
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

of the state of Minnesota.

Katherine Russell
Date 12/30/2022 Lic. No. P27101

Revisions
Description Date Num
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

28/12/2022 10:51:32

Comm: 216050
Date: 12/30/2022
Drawn:
Check: North

PENTHOUSE
ROOF FRAMING
PLAN - AREA 'H'

Scale: As indicated

PERMIT SET
NOT FOR CONSTRUCTION S2.03h
 Winneshiek
STEEL COLUMN
SEE PLAN & Expansion and
SCHEDULE MIN 2" NON-SHRINK GROUT
BELOW BASE PLATE, SEE PLAN Renovation
FOR T/FTG. ELEV.
E.4 E.6 1.91 1.91 SECOND STAGE
CONCRETE 1/2" EXP. JOINT TYP.
PIER VERT.
PIER VERT. PIER VERT. TOP REINFORCEMENT,
REINF. TYP.
SEE SCHED. REINF. TYP. REINF. TYP.
SEE SCHED.
IF REQUIRED, SEE SCHED. 4" SLAB ON GRADE, SEE PLAN 901 Montgomery St
SEE SCHED. PIER VERT.
HOOKS TYP.
REINF. TYP. T/SLAB Decorah, IA 52101
SEE SCHED.
SEE SCHED. SEE-ARCH.
TIES TYP.
TIES TYP. TIES TYP. SEE SCHED.
ANCHOR RODS, SEE DWG. S4.00 216051

1'-8"

1'-8"

1'-8"

1'-0"
SEE SCHED. SEE SCHED.
TOF

2'-8 1/2"

2'-8 1/2"

2'-8 1/2"
Winneshiek Medical

2'-0"
SEE PLAN HOOK BARS IF

SCHED.
5.0 5.0 5.0 REQUIRED, SEE SCHED.

SEE
1'-0"
Center

1'-0 1/2"

1'-0 1/2"

1'-0 1/2"
HOOKS TYP. TIES TYP. HOOKS TYP. (2)#4 FOOTING SEE Decorah, IA 52101
SEE SCHED. SEE SCHED. SEE SCHED. SCHEDULE FOR
HOOKS TYP.

3" CLR TYP

1'-0 3/4" 1'-7 1/4" DIM & REINF.
1'-0" 1'-0" SEE SCHED. 12 12 SEE SCHEDULE
1'-0" 1'-0" 1'-0 3/4" 1'-7 1/4" 2'-8"
2'-0"
(2)#4
2'-0" 2'-8"
12 12
Interior Foundation Scheme
IA PIER P1-A PIER P1-B PIER P2 PIER P3
2
PIER LONGITUDINAL REINF.

E.4 Bar. L1 (in) L2 (in)

E.6 #6 12 30
A.1 D.99 PIER VERT.
REINF. TYP.
E.6 2" NON-SRINK GROUT
TIES TYP. SEE SCHED. PIER VERT. 2'-9" PIER VERT. #7 16 40
REINF. TYP. 2'-8" REINF. TYP.
SEE SCHED. PIER VERT.
SEE SCHED. 1'-9" 1'-0" SEE SCHED. 2 3/4" BLOCKOUT FOR
REINF. TYP. 1'-7 3/4" 1'-0 1/4" TIES TYP. #8 20 50
SEE SCHED. SEE SCHED. GROUT AND LEVELING,
PIER VERT.
TIES TYP. REINF. TYP. TIES TYP. SEE PIER DETAIL
SEE SCHED. SEE SCHED. SEE SCHED.

1'-0"

1'-0"
PIER LEVEL

1'-0 1/2"

1'-0"
TIES TYP. SEE PLAN PLACE AT LEAST

1'-10"
3.0 3.0
2'-0"

2'-0"
4.0

2'-0"
SEE SCHED.
2.3 3 STIRRUPS PIER LONGITUDINAL REINFORCEMENT MUST BE BENT AS NOTED IN

2'-10 1/4"

2'-10 3/4"
ANCHOR RODS,
1'-0"

1'-0"
AND HOOKS 2/S3.00 AND 3/S3.00 UNLESS OTHERWISE NOTED IN PIER DETAIL.

1'-0"
HOOKS TYP. LONGITUDINAL SEE DWG. S4.00 THE FIRST 5", SEE DIMENSIONS L1 AND L2 TO BE RESPECTED AT TOP AND BOTTOM
3.1

1'-10 1/4"
SEE SCHED.
REINFORCEMENT, SEE SCHED ANCHORAGE.

1'-0 1/2"
HOOKS TYP.
1'-0" 1'-0" HOOKS TYP. SEE SCHED. SCHEDULE IF L2 DOES NOT FIT INTO THE PIER HOOK CAN BE PROVIDED.
SEE SCHED.
3'-0" HOOKS TYP.
2'-0" 1'-11 1/2"
SEE SCHED.
3'-0"
2'-6 1/2"
2'-1 1/4" 1'-0"
2'-0" 1'-0 1/4"
CONT. TOP BARS CONCRETE PIER,
3'-0 1/4" 3'-1 1/4"
IF REQUIRED, SEE SEE SCHEDULE
SCHEDULE
PIER P4 & P4-H PIER P5 PIER P6 PIER P7 PIER P8 EDGE BEAM THROUGH
TOF
L1 SEE PLAN

SCHED.
HOOK BARS IF REQUIRED,

SEE
SEE SCHEDULE
HATCHED AREA INDICATES BLOCKOUT FOR SECOND STAGE CONCRETE, TOS ACCORDING TO DETAIL 3/S3.00

3" CLR
SEE SCHEDULE

TYP
FOOTING, SEE SCHEDULE FOR
DIMENSIONS AND REINFORCEMENT

CONC. PIER REINF. LAYOUT

1 1/2" = 1'-0"
0 Exterior Foundation Scheme
3

C 2022 Quetica Professional Engineers, Inc.

All rights reserved.
This document is an instrument of service and is the property of
Quetica Professional Engineers, Inc. and may not be used or copied

3.0 E.4 D.99 without prior written consent.

S3.00

S3.00
7

6
DOWEL #5x3'-0" EQ.
LEGS.@16"OC
6" STEEL STUDS, SEE SLAB ON GRADE, SEE PLAN STEEL STUDS, STEEL STUDS,
ARCH.
#3 @8 OC. SEE ARCH. SEE ARCH.
STEEL STEEL
DOWEL #5x3'-0" EQ. LEGS @16" O.C #4 @8 L= 11'-0" DOWEL #5x3'-0" EQ. LEGS.@16"OC STUDS, SEE
DOWEL #5x3'-0" EQ. LEGS.@16"OC STUDS, SEE
TOS, SEE PLAN TOS, SEE PLAN ARCH. ARCH.
FINISH, SEE ARCH.
TOS SEE PLAN

8"

8"
WALL VERT REINF
SEE SCHED #4@8" OC.
1/2" GAP DOWEL #5x3'-0" EQ.
GRANULAR DOWEL #5x3'-0" EQ. LEGS.@16"OC 1'-6"x1'-6"

4'-0"

4'-0"
LEGS.@16"OC 1'-6"x1'-6"
BASE SUMP PUMP #4@8" OC. #4@8" OC. #4@8" OC.
SUMP PUMP
MATERIAL, 16
SEE ARCH FOUNDATION BEAM 16
FOUNDATION WALL HORIZ REINF #4@8" OC. 8" SLAB, REINF. W/MESH #4 #4@8" OC. #4@8" OC. 8" SLAB, REINF. W/MESH #4
WALL SEE SCHED 16 @8 OC. 16 @8 OC. #4@8" OC.
T CLEAN DRY SAND TO FILL
TOF VOID BETWEEN SLAB AN

1'-6"

1'-6"
SEE PLAN FOOTING
H

TOF, SEE PLAN TOF, SEE PLAN

STARTERS BARS
SEE SCHEDULE SEE SCHED

1'-6"

1'-6"
FOR FOOTING B/2 B/2
SIZE AND REINF VOID FORM 1"

2#4 CONT. 2#4 CONT. 2#4 CONT. 2#4 CONT. FOOTING SEE
9 3/4" 8" 5'-11 3/4" 3'-2 1/4" 8" 1'-8 1/4" FOOTING SEE SCHEDULE FOR DIM &
SCHEDULE FOR DIM & 3 3/4" 11'-4" 3'-4 1/4"
REINF.
Foundation Wall Exterior Typ. FOUNDATION BEAM JOINT WITH SLAB ON GRADE, TYP. REINF.
4 5

Elevator pit - Section 1 Elevator pit - Section 2

6 3/8" = 1'-0" 7 3/8" = 1'-0"
0 0

PLACE CORNER BARS AT

1/2" GAP OUTSIDE FACE WITH 2'-0"
LEG EACH WAY, MIN. SIZE
#3 @8O.C. DOWEL #5x3'-0" EQ. LEGS
AND SPACING TO MATCH
@16" O.C.
2x(4)#4@8" OC. HORIZONTAL WALL
#3 @8O.C. DOWELS #5x3'-0" EQ. LEGS.@16"OC REINFORCING.
1/2" GAP
#3 @8O.C.
TOS SEE PLAN ELASTIC SEALING #3 @10 O.C.
6"

SEE PLAN 8" MIN.

WALL VERT REINF

SEE SCHED #4 @8 L=9'-0" O.C. #4 @10 O.C. L=9'-0"
I hereby certify that this plan, specifcation or report was
WALL HORIZ DRILL 8" INTO EXISTING AND SET WITH ADHESIVE prepared by me or under my direct supervision and that I
REINF SEE SCHED T ANCHORAGE HILTI HY-200 OR EQUIVALENT am a duly Licsened Professional Engineer under the laws
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

EXISTING FOUNDATION of the state of Minnesota.

TOF
SEE PLAN EXISTING WALL
TOF W/ FOUNDATION
VOID FORM
H

1" GAP SEE PLAN Katherine Russell

VOID FORM 1"
Date 12/30/2022 Lic. No. P27101
SEE SCHEDULE
B/2 B/2 STARTERS BARS TYPICAL REINFORCED CONCRETE WALL PLAN. SEE
FOR FOOTING
SEE SCHEDULE STRUCTURAL NOTES FOR ADDITIONAL INFORMATION, Revisions
SIZE AND REINF 8" MIN.
2x(1)#4@8" OC. IF THERE IS ONLY ONE LAYER OF STEEL PROVIDE ONLY Description Date Num
ONE CORNER BAR.
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

Foundation beam and wall section Existing foundation wall and beam section Wall Foundation Joint With Existing Structure SECTION
8 9 10 11

1'-2"
8" 6"

6" STEEL STUDS,

28/12/2022 10:51:35

SEE ARCH. WALL REINF.

HAIRPINS BAR TO
FINISH, SEE ARCH. MATCH TYP. HORIZ. Comm: 216050
DOWEL #5x3'-0" EQ. LEGS.@16"OC WALL REINF. Date: 12/30/2022
T. LAP Drawn:
TOS SEE PLAN
Check: North
6"

FOUNDATION SECTIONS AND

T. LAP

WALL #4 @8" OC TYP. HORIZ.

#4@8" OC
HOOKED BAR TO
WALL REINF.
DETAILS
FOUNDATION, SEE

S SCHED FOR
DIMENSIONS AND
REINFORCEMENT
#4 @8" OC TYP. HORIZ.
MATCH TYP. HORIZ.
WALL REINF.

TOF WALL REINF.

SEE PLAN

Scale: As indicated
Grade Beam on Footing - Section Wall corner and elevator pit reinforcement detail.
12 13 PERMIT SET
NOT FOR CONSTRUCTION S3.00
 Winneshiek
Expansion and
1.0 1.112 2.3 1.0 2.0 Renovation

901 Montgomery St

S3.01
S3.01

S3.01
SLAB ON GRADE, SEE PLAN

5
13

9
Decorah, IA 52101

SIM.
2" GAP 8" 8 #4 HOOKED
(9) #7
DOWELS 216051
SEE PLAN

5'-2" 23" 23" 5'-2"

9 #7
20" 20" Winneshiek Medical
6 #6 8 #4 HOOKED
6 #4 HOOKED
DOWELS, SEE DETAIL
2 ROWS OF #4
PER 13/S3.01
#4 STIRRUPS @10"
DOWELS Center
4 #5 Decorah, IA 52101
(2) #4 STIRRUPS @6"

1" GAP

2'-3"
VOID FORM

IA
SEE PLAN
SEE SCHEDULE 6 #6

2"
4 #6
#4 @5 FOR DIMENSIONS AND 2" GAP #4 @5" SEE SCHED. #4 STIRRUPS @10" (6) #6
SEE SCHEDULE FOR VOID FORM
REINFORCEMENTS STIRRUPS VOID FORM
1" GAP VOID FORM 2" DIMENSIONS AND
9'-6"
REINFORCEMENTS.
SEE SCHEDULE 6 #6
VOID FROM 1" #4@10" FOR DIMENSIONS AND
#4 DOWELS DOWELS
BARS
REINFORCEMENTS Section
Strap Beam, Side View
BARS
Strap Beam, Side View 5
1 2

S3.01
10"

S3.01
S3.01

9
6
5
SIM.
1'-11" DOWELS #5 @16 O.C SLAB ON GRADE,
SEE PLAN
1.0 2.0 (9) #7 SEE PLAN
D.99 D.2
S3.01
14

2" GAP 8"

(8) #4 HOOKED
5'-2" DOWELS
20" 20"
(2) #4 23" 23"
1/2" GAP SEE BEAM REINFORCEMENT 8 #4 HOOKED 9'-6" 9 #7
#4 STIRRUPS @10" 7 #7 IN ELEVATION 6 #6 #5 @8" O.C
3/4" GAP DOWELS 4 #5
#4 TIES @10"

1" GAP
(6) #6

1'-11"
VOID FORM 1"

2"
VOID FORM 1" #4 STIRRUPS @10" #4 STIRRUPS 6 #6
1/2" VOID FORM SEE SCHEDULE FOR 6 #6 #4 STIRRUPS @10"
2" GAP @5" SEE SCHED. SEE SCHEDULE FOR
DIMENSIONS AND VOID FORM SEE PLAN
SEE SCHEDULE DIMENSIONS AND
REINFORCEMENTS
FOR DIMENSIONS AND REINFORCEMENTS
REINFORCEMENTS VOID FORM 6 #6
6 #6 9'-6"
VOID FORM VOID FORM

Strap Beam, Front View Strap Beam, Side View Section

3 4 6
C 2022 Quetica Professional Engineers, Inc.
All rights reserved.
This document is an instrument of service and is the property of
Quetica Professional Engineers, Inc. and may not be used or copied
without prior written consent.

2.0 1.0

S3.01
10"

S3.01

S3.01
9

5
2.0 1.0
S3.01

SLAB ON GRADE
15

SIM.
1'-11" DOWELS #5 @16 O.C SEE PLAN
TYP.

8" 2" 20" 20"

5'-2" 5'-2" (9) #7 SEE PLAN
18" 18" 9'-6" 18"
8 #4 HOOKED 8 #4 HOOKED
9 #7 DOWELS 9 #7 4 #5 6 #6 DOWELS
4 #5

1'-9"
#4 STIRRUPS @10"
#5 @8

1" GAP
#4 STIRRUPS @10" #4 STIRRUPS
6 #6 SEE SCHED. 6 #6 @5"
SEE SCHEDULE FOR VOID FORM #4 TIES @10"
VOID FORM
DIMENSIONS AND #4 STIRRUPS @10" VOID
REINFORCEMENTS VOID FORM
VOID FORM FORM 2" GAP
Strap Beam, Side View Strap Beam, Side View
7 8 SEE PLAN

6 #6
VOID FORM

Section
9
6" STEEL STUDS,
6" 8" 1'-6"
SEE ARCH.
HAIRPIN #3 @10
1'-6"
FINISH, SEE ARCH.
11" SLAP ON GRADE, SEE PLAN
DOWEL #5 @16 OC.
DOWELS #5 @16 O.C SLAB ON GRADE, SEE PLAN
1'-6" 1'-6"
SLAB ON GRADE, SEE PLAN SLAB ON GRADE, SEE PLAN EXISTING
SEE PLAN STRUCTURE DOWELS #5@16" O.C
SEE PLAN SLAB ON GRADE, SEE PLAN SEE PLAN
SEE PLAN #4@10
4"

(5) #7
6"

8"

SEE PLAN
1/2"
(7) #7
20" I hereby certify that this plan, specifcation or report was
(6) #7 20"
(2) #5 #3 TIES @10" prepared by me or under my direct supervision and that I
3 #5 TOB
(6) #6 #4 TIES @10" am a duly Licsened Professional Engineer under the laws
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

#4@10 OC. L=9'-0" of the state of Minnesota.

2'-0 1/8"

#3 TIE @10" O.C

#3 TIES @10" (2) #4 (4) #4
(4) #3 HOOK #3@10" OC. (4) #4
(4) #5
Katherine Russell
3 #5 #4 TIES @10" Date 12/30/2022 Lic. No. P27101
#5@8 O.C
BOT SEE PLAN
(5) #7 4 #6 6 #6 Revisions
20" 20" SEE PLAN Description Date Num
VOID FORM SEE PLAN SEE PLAN
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

(7) #7
Section SEE PLAN
10 VOID FORM 1" VOID FORM 1" VOID FORM 1"

VOID FORM

Section Section Section Section

11 12 13 14
#5 @16" O.C X 3'-0" EQ. LEGS
1.91 SLAB ON GRADE, SEE PLAN G.96 D.22 C.22
28/12/2022 10:51:38

1/2"
Comm: 216050
31'-3" 10"
(2) #5 Date: 12/30/2022

SEE PLAN Drawn:

S3.01
S3.01

HAIRPINS #3 @10" 1'-10" North

18

Check:
12

#4@10 SLAB ON GRADE, SEE PLAN DOWELS #5 @16 O.C

4'
8 #4 HOOKED
DOWELS
(5) #7 (4) #5 SEE 4/S3.01
8 #4 HOOKED
SECTIONS AND
5'-2" 9'-6" 4 #5 (9) #7
9 #7 SEE 4/S3.01 8 #4 HOOKED
DOWELS 9#7
23" 23" DOWELS TOS SEE PLAN
DETAILS
#3 TIES @10"

S #3 HOOKS @10"
4-#5
2'-1"

2'-6"

4 #5
#4 STIRRUPS
5 3/8"

#3 TIE @10 (5) #7 SEE SCHEDULE #4@5"OC SEE SCHED. SEE SCHEDULE FOR
FOR DIMENSIONS AND VOID FORM #4 STIRRUPS @10" 6#6 DIMENSIONS AND
6 #6 4'-0" 4'-0" REINFORCEMENTS
SEE PLAN REINFORCEMENTS 12'-0"
VOID FORM
EXISTING FOUNDATION WALL Scale: As indicated
(6) #6
VOID FORM

PERMIT SET
15
Strap Beam, Section
16
Section Typ
17
STRAP BEAM, SIDE VIEW
18
SECTION 18
NOT FOR CONSTRUCTION S3.01
 WIDTH Winneshiek
(W) Expansion and
PROVIDE 5/8"Øx1'-2"@18"OC
Renovation

SEE PLAN
SMOOTH BAR, GREASE ONE
END, CENTER ON JOINT.
SEE ARCH DRAWINGS FOR
NON-BEARING WALLS NOT
SHOWN ON STRUCTURAL
DRAWINGS
901 Montgomery St
EXISTING WALL AREA
TO BE DEMOLISHED DOWEL #5@18" OC. Decorah, IA 52101
VAPOR BARRIER FOR INTERNAL 1/2" GAP
SLABS ON GRADE, SEE PLAN EXISTING BUILDING 1/2" 216051

CUT 1/4 OF SLAB

8" MIN. SMOOTH BAR #4 @ 10"- ELASTIC SEALING

THICKNESS
HALF PAINTED AND GREASED W/ GASKET
Winneshiek Medical

SEE PLAN

4"
CONCRETE SLAB ON GRADE SAWCUT JOINT WITHIN 12 TOS SEE PLAN
HOURS AFTER PLACING SLAB.

4"
SEE PLAN
Center

6"
Decorah, IA 52101

2"
GRANULAR MATERIAL, EXISTING GROUND 2'-0" 6"

8"
SEE ARCH/CIVIL FLOOR SLAB 2'-0" 6"

DRILL 12" INTO EXISTING GROUND FLOOR GROUND FLOOR

GENERAL BACKFILLING, AND SET WITH ADHESIVE. SLAB SLAB
SEE CIVIL DESIGN
THICKENED SLAB

IA TYPICAL CONTROL JOINT

SEE STRUCTURAL NOTES FOR JOINT SPACING
W/2-#4 CONT 2W
NOTE: CUT CONCRETE OF EXISTING WALL TO MATCH GROUND SLAB
THICKNESS. EXISTING DOWELS TO BE CUTTED

Slab on Grade. Typical Section SECTION SECTION Ground Slab With Existing Wall and pavement Joint Ground Floor Slab Joint With Existing Structure 2.
1 2 3 4 5

STEEL COLUMN SEE

PLAN AND SCHEDULE

2S+0.25T 2S 2S
STEEL COLUMN SEE
PLAN AND SCHEDULE 0.25T
SEE ARCH FOR STOOP SIZE
#4x3'-0"@12"OC
DOWELS, CENTER FILL IN DIAMOND 7 DAYS MIN
#4@12"OC EACH WAY BOTTOM,
ON JOINT.

S
1 1/2" CLEAR COVER AFTER SLAB HAS BEEN PLACED.
SEE ARCH FOR JOINT
PAPER JOINT
4" MIN

SLOPE 1/4" SIZE AND LOCATION.

4 SIDES

S
PER FT
FILL IN DIAMOND 7 DAYS MIN
8" TYP

AFTER SLAB HAS BEEN PLACED.

S
PAPER JOINT

T
4 SIDES
CONT REINF

T
#4x3'-0"@12"OC #4x3'-0"@12"OC
DOWELS, EQUAL LEGS. DOWELS, EQUAL LEGS UNLESS NOTED:
S=8" FOR MASONRY WALLS
S=12" FOR CONC WALLS
8" TYP SEE TYPICAL CONTROL / T = SCHEDULED FOOTING THICKNESS
3 SIDES CONSTRUCTION JOINT DETAILS.
NOTE: SEE PLAN AND
SCHEDULES FOR
WALL AND FOOTING
REINFORCEMENT TYPICAL SLAB DETAIL AT STEEL TUBE COLUMN TYPICAL DETAIL FOR STEPPING FOOTING
SEE TYPICAL CONTROL /
CONSTRUCTION JOINT DETAILS.

C 2022 Quetica Professional Engineers, Inc.

All rights reserved.
SECTION Typical slab detail at steel tube column SECTION SECTION This document is an instrument of service and is the property of
6 7 8 9 Quetica Professional Engineers, Inc. and may not be used or copied
without prior written consent.

NOTES:
1. USE THIS DETAIL FOR PIPES UP TO 4'-0" BELOW FOOTING.
2. FOR PIPES DEEPER THAN 4'-0" BELOW FOOTING USE STEPPED
4.22 3.22
B A
FOOTING DETAIL TO STEP FOOTING TO WITHIN 4'-0" MAXIMUM.
3. COORDINATE PIPING LOCATIONS WITH MECHANICAL DRAWINGS.
#5@8"OC EACH WAY,
EACH FACE OF WALL

S3.01
ALL AROUND SHAFT

18
#4X3-0"@16"OC DWLS, 2-#4 CONT WALLS DOWELS TO MATCH CONCRETE
EQUAL LEGS WALL REINFORCING SIZE AND
4" CONC SLAB W/#3@ SPACING, PROJECT 3'-0" INTO
12"OC EACH WAY ON WALL
SLEEVE AND PIPE 4" MIN SAND CUSHION.
THROUGH WALL.
23" 23" 4'-6"

0'- 1".
SEE 4/S3.01
5'-2"
FTG

8 #4 HOOKED 9'-6" 4 #5
DOWELS 9#7

#5@8"OC EACH WAY,

4' - 0".

EACH FACE OF WALL ALL

AROUND SHAFT WALLS 4" CONC SLAB W/#3@12"OC EACH WAY ON

2'-1"

2'-6"
CLEAN DRY SAND TO FILL VOID BETWEEN SLAB
AND FOOTING
4'-0" MAX

D = SLEEVE SIZE

SLEEVE TO BE 4" 11" 8" 6'-0" 1'-9"

LARGER THAN PIPE.
D + 1'-6" #4@5"OC SEE SCHED. SEE SCHEDULE FOR
EXISTING #4 STIRRUPS @10" VOID FORM 6#6 DIMENSIONS AND
SEE SCHEDULE FOR REINFORCEMENT.
EXISTING FOUNDATION FOUNDATION 4'-0" 4'-0" REINFORCEMENTS
WALL WALL 12'-0"
1'-6"
6"

DETAIL A DETAIL B
SEE SCHEDULE FOR
REINFORCEMENT

DETAIL ELEVATOR TYPICAL DETAIL DUMPWAITER TYPICAL DETAIL STRAP BEAM

10 11 12 13

PIPE
PERPENDICULAR TO I hereby certify that this plan, specifcation or report was
FOUNDATION WALL prepared by me or under my direct supervision and that I
& FOOTING. am a duly Licsened Professional Engineer under the laws
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

of the state of Minnesota.

Katherine Russell
Date 12/30/2022 Lic. No. P27101
SEE PLAN
FTG

#5@8"OC EACH WAY, Revisions

EACH FACE OF WALL ALL
AROUND SHAFT WALLS 4" CONC SLAB W/#3@12"OC EACH WAY ON Description Date Num
CLEAN DRY SAND TO FILL VOID BETWEEN SLAB
AS REQ'D
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

AND FOOTING
2 2
1 1
1'-6"
6"

SUMP PIT

PIPE SLEEVE DIA

1'-6"

PERPENDICULAR TO
+ 1'-6"
FOUNDATION WALL
& FOOTING.
NOTES:
28/12/2022 10:51:39

1. FOR PIPES BELOW FOOTING PROVIDE SLEEVE & THICKEN CONCRETE

FOOTING AS SHOWN OR STEP FOOTING BELOW PIPE PER 9/S3.02. Comm: 216050
2. FOR PIPES WITHIN FOOTING DEPTH STEP FOOTING PER 9/S3.02 SO PIPES SEE SCHEDULE FOR Date: 12/30/2022
PASS THROUGH WALL. PROVIDE SLEEVE & GROUT INTO WALL. REINFORCEMENT

3. SLEEVE DIAMETER TO BE 2" GREATER THAN PIPE OUTSIDE DIAMETER. Drawn:

Check: North

DETAIL ELEVATOR TYPICAL DETAIL

14 15
SECTIONS AND
DETAILS
S

Scale: As indicated

PERMIT SET
NOT FOR CONSTRUCTION S3.02
 SEE PLAN

3/8" X CONT. PLATE WITH A

4" VERT. LEG X HORZ. LEG
FROM CENTER LINE OF
BEAM TO FACE OF STUD.
Winneshiek
WELD DECK
WELD DECK TO ANGLE PER
4/S4.00 3/16 2@12 L6X6X5/16 X CONT. WELD
6X1/4 CONT. PLATE
W/1/2"ØX4" H.S. @ 24" O.C.
Expansion and
3X1/4 CONT. PLATE 3X1/4 CONT. PLATE
TO BEAM
PER 4/S4.00
W/1/2"ØX4" H.S. @ 24" O.C.
WELD DECK TO PLATE PER
4/S4.00
W/1/2"ØX6" H.S. @ 24" O.C.
WELD DECK TO PLATE PER
4/S4.00
DECK TO ANGLE PER 4/S4.00. WELD DECK TO PLATE PER
4/S4.00
Renovation
CONNECTION OF STUDS TO CONCRETE WALL,
ANGLE BY STUD SUPPLIER. SEE PLAN
901 Montgomery St
SEE PLAN FOR
Decorah, IA 52101
DECK DIRECTION.
CONCRETE WALL,
CONCRETE WALL,
SEE PLAN CONCRETE WALL,
3/16
SEE PLAN 216051
SEE PLAN
STEEL BEAM, SEE
PLAN 3/16 Winneshiek Medical
Center
Decorah, IA 52101
SECTION SECTION SECTION SECTION SECTION SECTION
1 2 3 4 5 6

IA GRID

3/8" X CONT. PLATE WITH A

4" VERT. LEG X HORZ. LEG SEE PLAN
FROM CENTER LINE OF
BEAM TO FACE OF STUD.
WELD DECK TO ANGLE PER
4/S4.00
GRID 1 1/2" 1 1/2"
2" 2" 3/8''
3/16 2@12

3"

3"
SEE PLAN
STEEL COLUMN
STEEL STUDS, SEE

3"

3"
SEE PLAN AND SCHEDULE
ARCH.
2" 2"
PLATE TH 3/4" + STEEL PLATE 1 1/2" 1 1/2"
3/16 2@12
8 BOLTS Ø 3/4''
CONNECTION OF STUDS TO
ANGLE BY STUD SUPPLIER.
3/16 2@12
2@12 L 3x 3 x 1/4 x CONT. WELD DECK TO ANGLE PER 4/S4.00
STIFFENERS 5/8
2@12
TWO SIDES
1/4"
CONC. CURB, SEE ARCH. 3 SIDES TYP
1/4"
STEEL BEAM
W/ STD. CONN.,
SEE PLAN
HSS 2 1/2X2 1/2X1/8" X
CONT. WELD DECK TO HSS
PER 4/S4.00 L 8 x 4 x 7/16 x CONT. WELD
DECK TO ANGLE PER
4/S4.00 MAIN BEAM TRANSFER BEAM; SEE PLAN

SECTION Change in roof deck type. SECTION Transfer beam. Side view H
7 8 9 10
C 2022 Quetica Professional Engineers, Inc.
All rights reserved.
This document is an instrument of service and is the property of
Quetica Professional Engineers, Inc. and may not be used or copied
without prior written consent.

STEEL STUDS, SEE ARCH. POURSTOP/CLOSURE PLATE,

CONNECTION TO BY DECK SUPPLIER CL
CL CL
COMPOSITE DECK BY BM.
EXIST. BM. 3/16 3@12 SEE
STUD SUPPLIER. SEE PLAN
BM. COMPOSITE FLOOR SLAB.
ADDITIONAL SLAB REINF, DECK DIRECTION VARIES. PLAN #3@10"OC.
6"x18GA. CONT PLATE, CL CL
SEE PLAN SEE PLAN 2" GAP COMPOSITE BM.
CENTERED OVER DECK EXIST. BLDG. EXIST. 3/16 3@12
#3@8OC FLOOR SLAB.
TRANSITION AND 2' - 6" BM. SEE PLAN COMPOSITE FLOOR SLAB. DECK
2" 10" DECK DIRECTION
FASTENED W/ 2-#10 TEK 3/8" CONT BENT PLATE DIRECTION VARIES.
VARIES. SEE PLAN
SCREWS @ 6"OC W/1/2''Øx4@18OC " HS 2#5 EXIST. BLDG. #3@8OC
2" 10"

EXIST. BLDG.
COMPOSITE DECK,
SEE PLAN, EXTEND ANGLE TO #4 @ 12" OC EXTEND A
TO ROOF BEAM STEEL BEAM MINIMUM OF 30" INTO SLAB
3/16 3@12 PAST BEAM CENTERLINE

6X1/4 CONT. PLATE

#4 @ 12" OC EXTEND A W/1/2"ØX4" H.S. @ 24" O.C.
WELD DECK TO PLATE PER
MINIMUM OF 30" INTO SLAB 4/S4.00
PAST BEAM CENTERLINE 3/8" CONT BENT PLATE
CONC. WALL
ROOF BEAM, SEE PLAN W/1/2''Øx4@18OC " HS
DOWEL #5@ 18"OC, WELDED TO
FLOOR BEAM, SEE PLAN
EXISTING COMPOSITE DECK EDGE
ANGLE, GREASED AT ONE SIDE. ELASTIC SEALING
DOWEL #5@ 18"OC, WELDED TO EXISTING COMPOSITE
CONT 3/8" BENT PLATE DECK EDGE ANGLE, GREASED AT ONE SIDE.
TO MATCH RADIUS OF
SLAB CONT 3/8" BENT PLATE
TO MATCH RADIUS OF SLAB
ELASTIC SEALING ELASTIC SEALING

TYPICAL DETAIL Composite deck edge. Section Composite deck edge. Section Composite deck edge. Section
11 12 13 14

I hereby certify that this plan, specifcation or report was

prepared by me or under my direct supervision and that I
am a duly Licsened Professional Engineer under the laws
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

of the state of Minnesota.

Katherine Russell
Date 12/30/2022 Lic. No. P27101

Revisions
Description Date Num
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

28/12/2022 10:51:41

Comm: 216050
Date: 12/30/2022
Drawn:
Check: North

SECTIONS AND
DETAILS
S

Scale: As indicated

PERMIT SET
NOT FOR CONSTRUCTION S3.03
 Winneshiek
STEEL BEAM, SEE PLAN STEEL BEAM, SEE PLAN
7" L 7" STEEL BEAM, SEE PLAN
L
STEEL BEAM, SEE PLAN
Expansion and
A A Renovation

EQ

EQ

EQ
901 Montgomery St

EQ
Decorah, IA 52101

H
R = 1"

D
R = 1"
216051

EQ
EQ

EQ
EQ
Winneshiek Medical
2-3/8"x3"
PLATES EACH
1/4
TYP Center
SIDE OF WEB 1/4 3" LONG STEEL Decorah, IA 52101

EQ
PIPE SLEEVE

1/2"
NOTES: NOTES:
1. HOLES SHALL BE SHOP CUT AND GROUND SMOOTH. NOTES:
1. HOLES SHALL BE SHOP CUT AND GROUND SMOOTH.
NOTES: 2. NO FIELD CUTTING OR TORCHING TO ENLARGE 1. HOLES SHALL BE SHOP CUT AND GROUND SMOOTH.
2. NO FIELD CUTTING OR TORCHING TO ENLARGE
1. HOLES SHALL BE SHOP CUT AND GROUND HOLES IS PERMITTED. 2. NO FIELD CUTTING OR TORCHING TO ENLARGE
HOLES IS PERMITTED.

EQ
SMOOTH. 3. SEE PLAN FOR SIZE AND LOCATION OF OPENING. HOLES IS PERMITTED.
3. SEE PLAN FOR SIZE AND LOCATION OF OPENING.

IA
H
2. NO FIELD CUTTING OR TORCHING TO 3. SEE PLAN FOR SIZE AND LOCATION OF OPENING. 3/16
ENLARGE HOLES IS PERMITTED. 4. VERIFY WITH MECH ON PIPE PENETRATION
3. SEE PLAN FOR SIZE AND LOCATION OF LOCATIONS.

1/2"
OPENING.
A
A

Mechanical opening 1 Mechanical opening 2 Mechanical opening 3 Mechanical opening 4

1 2 3 4

S3.04
17
1 3/4" STEEL COLUMN 3/8''
1/2"
STEEL COLUMN SEE PLAN AND SCHEDULE
PLAN UNCOPED END

4" TYP
PLATE TH 3/4" + STEEL PLATE
1/2" 1 3/4" 4 BOLTS Ø 1'' 2" 2"

≥ 2"
STEEL COLUMN

PLAN COPED END STEEL BEAM

1 3/4"
1/2" STIFFENERS, TH 3/8"

1/2" TYP
PLATE OR DOUBLE TWO SIDES
ANGLE CONNECTION
WITH Ø 3/4 BOLTS, 1/4"
1 3/4" STEEL BEAM 3 SIDES, TYP
SEE SCHEDULE UNCOPED BEAM END 1/2" 1/4"
STEEL COLUMN

W21 BEAM; SEE PLAN

TRANSFER BEAM W27; SEE PLAN

S3.04
17
Column- beam connection. Side view Column- beam coped connection. Plan view Column- beam uncoped connection. Plan view Transfer beam. Side view C 2022 Quetica Professional Engineers, Inc.
5 6 7 8 All rights reserved.
This document is an instrument of service and is the property of
Quetica Professional Engineers, Inc. and may not be used or copied
without prior written consent.

1/4"
3 SIDES TYP
1/4"
SEE PLAN FOR PURLIN SPACING
STEEL BEAM, SEE PLAN STEEL BEAM; 1/4"
SEE PLAN 3 SIDES TYP
1/4" 2" MIN 6 Ø MIN EQ STUD SPACING BETWEEN PURLINS 2"

6Ø MIN #3@8OC
CENTERLINE #4x5'-0'' @ 8"@OC, CENTER OVER
OF PURLIN GIRDER PROVIDE 3/4'' COVER OVER
4 STIFFENERS 5/8 4 STIFFENERS 5/8
BARS SPLIT DECK AS NECESSARY TO
#3@8OC TOP REINFORCEMENT #4x5'-0'' @ FACILITATE ATTACHMENT TO GIRDER

STEEL
BEAM
4Ø MIN

8"@OC, CENTER OVER GIRDER

PROVIDE 3/4'' COVER OVER BARS
COMPOSITE COMPOSITE FLOOR SLAB
FLOOR SLAB

6 Ø MIN
PLATE TH=3/4" +
PLATE TH= 3/4" + (4) 3/4" Ø BOLTS TYP
4 BOLTS Ø 3/4'' TYP 5/16"
5/16"
HSS COLUMN;
W COLUMN, GIRDER PARALLEL TO DECK SPAN
SEE PLAN
SEE PLAN AND SCHEDULE 1. SEE PLAN FOR NUMBER OF STUDS. A
SINGLE NUMBER FOR BEAM SPAN
SIGNIFIES A UNIFORM DISTRIBUTION COPED BEAM END PURLIN PURLIN
MULTIPLE NUMBER SIGNIFY SEGMENTS
2" TYP

1" TYP 2" TYP DISTRIBUTION BETWEEN MAJOR PURLINS.

DECK CLOSURE BY
1" TYP

2. WHERE MINIMUM SPACING CANNOT BE PURLIN PERPENDICULAR TO DECK SPAN

MET WITH SINGLE ROW OF STUDS, PLACE 1. SEE PLAN FOR NUMBER OF STUDS. SUPPLIER MAIN BEAM
STUDS IN DOUBLE ROW. SPACE STUDS UNIFORMLY ALONG
2" TYP

LENGTH OF PURLIN.

2" TYP

Cantilever beam. Side view Headed studs disposition. Detail Composite deck. Section 1 Composite deck. Distribution Reinforcement
9 10 11 12

BEAM IF REQUIRED SEE PLAN COPE BEAM FLANGES AT

(4) #4@8"OC.

4 3/4"
GAP 1/2" 2" 3" 2" ONE SIDE ONLY T&B
#3@8"OC. (4) #4@8"OC.
#3@8OC STEEL STUDS, SEE COMPOSITE FLOOR SLAB.
CONSTRUCTION ARCH, CONNECTION DECK DIRECTION VARIES.
SEE PLAN SPLIT DECK AS NECESSARY TO #3@8"OC.
JOINT OF STUD TO ANGLE 2' - 6" 8 BOLTS Ø 1"
FACILITATE ATTACHMENT TO GIRDER STEEL STUDS, SEE COMPOSITE
COMPOSITE

4" 4" 4"

#4x4'-0'' @ 8@OC, BY SUPPLIER ARCH, CONNECTION FLOOR SLAB.
FLOOR SLAB TOP #4x5'-0'' @ 8"OC, CENTER OVER SEE PLAN 2' - 6"
CENTER ON JOINT OF STUD TO ANGLE DECK DIRECTION
GIRDER PROVIDE 3/4'' COVER OVER #3@8OC BY SUPPLIER VARIES.
EQ EQ

BARS
3/8" CONT BENT PLATE COMPOSITE FLOOR SLAB
W/1/2''Øx4@18OC " HS I hereby certify that this plan, specifcation or report was
prepared by me or under my direct supervision and that I

4 3/4"
SINGLE PLATE OF STIFFENER am a duly Licsened Professional Engineer under the laws
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

ANGLE TO of the state of Minnesota.

SINGLE PLATE TH 1/2",
STEEL BEAM 3/8" CONT BENT PLATE
3/16 3@12 TRANSFER BEAM; SEE PLAN W/ 3/4"x3/4" SNIP
W/1/2''Øx4@18OC " HS ANGLE TO 1/4"
3/16 3@12 STEEL BEAM 3 SIDES, TYP
1/4" Katherine Russell
Date 12/30/2022 Lic. No. P27101
PURLIN

Revisions
Description Date Num
Composite deck construction joint. Composite deck edge. Section Composite deck on purlin. Distribution reinforcement Composite deck edge. Section Transfe beam. Side view.
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

13 14 15 16 17
DIM 'S'
CENTERLINE JOIST OR PURLIN

(4) #4@8"OC.
JOIST TOP CHORD OR PURLIN ROOF DECK SPAN DIRECTION CL
TOP FLANGE CL #3@8"OC.
BENT PLATE 3/8" WITH 4" VERT. LEGS BM.
NOTE: SIDE FRAMING BM. COMPOSITE
STEEL FLOOR SLAB.
ANGLE MAY BE SEE PLAN
STUDS, SEE 2 FRAMING ANGLE (TOP FLUSH 3/16 3@12 2' - 6" DECK DIRECTION
OMITTED WHEN 3/16 3@12
ARCH. WITH TOP OF BEAMS). PROVIDE COMPOSITE 3/8" CONT BENT PLATE VARIES.
DIMENSION 'A' IS 12"
28/12/2022 10:51:45

COMPOSITE FLOOR
L3X3X1/4 IF DIM 'L' IS LESS OR LESS. FLOOR SLAB. W/1/2''Øx4@18OC " HS
SLAB. DECK
THAN 3'-6". PROVIDE L5X3X3/8 IF SEE PLAN DECK DIRECTION Comm: 216050
#3@8OC SEE PLAN DIRECTION VARIES.
'L' IS BETWEEN 3'-6" AND 7'-0" VARIES. #3@8OC SEE PLAN Date: 12/30/2022
SEE PLAN
ANGLE TO TYP
3/16 Drawn:
3/16 @10 BEAM TYP COORDINATE SIZE AND
DIM. 'L'

LOCATION OF OPENINGS Check: North

DIM. 'A'
WITH ARCH AND MECH PRIOR
TO FABRICATION ANGLE TO
CONT 3/8" STEEL BEAM
STEEL STUDS PANEL, SEE ARCH
4 - 8 1/2X4X3/8X0'-5" BENT PLATE
(PLACE 3/8" ABOVE CHANNELS)
BENT PLATE
TO MATCH
CONT 3/8" BENT
PLATE
3/16 3@12
SECTIONS AND
ANGLE 'A' TO MATCH
BENT PLATE 3/8" WITH 4" VERT. LEGS
TIGHT TO TOP EDGE OF BEAM. RADIUS OF
SLAB
RADIUS OF
SLAB
DETAILS
TYP

S END FRAMING MEMBER MAY BE

OMITTED WHEN THE OPENING IS
LESS THAN 12" FROM GIRDER
CENTERLINE. EXTEND SIDE ANGLES
3/16
#4 @ 12" OC EXTEND A
MINIMUM OF 30" INTO SLAB
#4 @ 12" OC EXTEND A
MINIMUM OF 30" INTO SLAB
TO GIRDER. C8X11.5 EACH END PAST BEAM CENTERLINE
PAST BEAM CENTERLINE

Stud panel fixing Opening in Composite Deck Composite deck edge. Section Composite deck edge. Section Composite deck edge. Section
18 19 20 21 22
Scale: As indicated

PERMIT SET
NOT FOR CONSTRUCTION S3.04
 Winneshiek
Expansion and
GRID
Renovation
GRID
L 6 x 6 x 3/8 x CONT. 3/16 2@12
SEE PLAN BENT PLATE 3/8" CONT. W/ 4" VERT. LEG
AND HORIZONTAL LEG FRONT FACE L6x6 SEE PLAN 901 Montgomery St
TO CENTER LINE OF BEAM L 2 ½ x 2 ½ x 5/16
x CONT. WELD
L 6 x 6 x 3/8 x CONT. Decorah, IA 52101
DECK TO TO
GRID 3/16 2@12
ANGLE AS PER
4/S4.00
216051
C6X8.2 CHANNELS TOES 3/16 3/16 2 @ 12
HANDRAIL DOWN OVER DECK FLUTES
@48" OC, WELD TO JOIST AND DECK
ROOF DECK, SEE PLAN
CONC. CURB, SEE ARCH.
Winneshiek Medical
CONC. CURB, SEE ARCH. 3/16
Center
3/16 2@12 2" DECK WELD Decorah, IA 52101
C10x15.3 TO STEEL BEAMS
W/1/2"Øx4 HS @18" OC. PER 4/S4.00
JOIST
HSS 2 1/2"x2 1/2"x1/8"x CONT.
JOIST BRIDGING AS REQUIRED WELD TO W BEAM

IA BY JOIST SUPPLIER 2" DECK WELD STEEL BEAM

DECK DIRECTION VARIES, TO STEEL BEAMS

4"
3/16 2@12 L HSS 2 1/2 x 2 1/2 x 3/16 W/ STD. CONN.,
SEE PLAN PER 4/S4.00
WELD ROOF DECK TO 2@12 SEE PLAN
TUBE AS PER 4/S4.00
2@12
3/8" BENT PLATE Lx4"
2@12

2@12 MAIN BEAM

3/16 2@12
3/16 2@12

Handrail suport. Section Change in roof deck type. Side View Change in roof deck type.
1 2 3

3 SIDES, CJP,
TYP
BEAM TO
PLATE, CJP, GRID

S3.05
TYP 5/16

9
3 SIDES, TYP

S3.05
GRID

6
5/16
5/16 GRID
3 SIDES TYP SEE SCHEDULE
5/16 (4) BOLTS Ø 3/4"
S3.05

S3.05
6

6
BEAM TO 1 3/4" 4" 1 3/4"

1 3/4"
PLATE, CJP,

1" TYP
(8) BOLTS Ø 3/4" TYP

1 3/4"
CJP
STIFFENER th = 3/8" 5/16 STIFFENER th = 3/8"
2 SIDES
BOTH SIDES, TYP BOTH SIDES, TYP

1 3/4"
TYP 5/16
STIFFENER th = 3/8"
5/16 BOTH SIDES, TYP
2 SIDES
C 2022 Quetica Professional Engineers, Inc.
TYP 5/16 (4) Ø BOLTS 3/4" All rights reserved.
END PLATE 1/2" MIN TYP This document is an instrument of service and is the property of
th = 1/2" Quetica Professional Engineers, Inc. and may not be used or copied
without prior written consent.

1 3/4"

1 3/4"
(8) 3/4" Ø BOLTS STIFFENER
th = 5/8", TYP

2 5/8"

1 3/4"
STIFFENER 3/8

1" TYP
th = 5/8",TYP TYP
3/8
3 SIDES, TYP

S3.05
3/8

6
5/16
END PLATE
3/8 th = 3/4", TYP
S3.05

S3.05

END PLATE

3/4" TYP
STIFFENERS th = 3/8"
6

th = 3/4" TYP
BOTH SIDES
3/4" TYP

STIFFENERS th = 3/8" 3 SIDES, TYP 3/4" TYP

S3.05
BOTH SIDES 5/16

9
3/4" TYP

Intermediate column- beam moment connection 1. Side view End column- beam moment connection 2. Side view Column-beam moment connection. Front view.
4 5 6

3 SIDES, CJP,
3/4" TYP TYP
3/4" TYP

STIFFENERS th=3/8" GRID

BOTH SIDES GRID 5/16 3 SIDES CJP,
TYP
3 SIDES, TYP GRID
S3.05

S3.05
BEAM TO
S3.05

6
5/16
S3.05

PLATE, CJP, COPE BEAM FLANGES AT

BEAM TO
6

TYP GAP 1/2" ONE SIDE ONLY T&B

PLATE, CJP, 2" 3" 2"
SEE SCHEDULE (8) BOLTS 3/4" TYP
COLUMN BEAM CONNECTION
(4) BOLTS Ø 3/4" SEE DETAIL 5/S3.04

2 7/8"
8 BOLTS Ø 1"

4"
3/4" TYP
STIFFENER th = 3/8"

4"
5/16 BOTH SIDES, TYP
2 SIDES
5/16 STIFFENER th = 3/8"
STIFFENER th = 3/8" 2 SIDES TYP 5/16
BOTH SIDES, TYP
BOTH SIDES, TYP TYP 5/16

4"
I hereby certify that this plan, specifcation or report was
10"

2 7/8"
prepared by me or under my direct supervision and that I
am a duly Licsened Professional Engineer under the laws
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

of the state of Minnesota.

(4) BOLTS Ø 3/4" (8) 3/4" BOLTS 1/4"

3 SIDES, TYP
1/4"
Katherine Russell
1/2" GAP STIFFENER Date 12/30/2022 Lic. No. P27101
10" SINGLE PLATE OF STIFFENER
STIFFENER th = 5/8",TYP
th = 5/8", TYP
Revisions
5/16 3/8 Description Date Num
3/8 3 SIDES, TYP TYP
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

TYP 5/16 3/8

NOTE: USE BEAMS TO ONE OR BOTH SIDES
S3.05

S3.05
3/8 END PLATE
AS INDICATED IN PLAN VIEW.
6

6
S3.05

th = 3/4" TYP
6

END PLATE
th = 3/4", TYP
3/4" TYP

STIFFENERS th = 3/8" 3 SIDES, TYP

3/4" TYP

STIFFENERS th = 3/8" BOTH SIDES 5/16 STIFFENERS th = 3/8"

BOTH SIDES BOTH SIDES
3/4" TYP
S3.05
9

3/4" TYP
28/12/2022 10:51:49

End column- beam moment connection 3. Side view Intermediate column- beam moment connection 4. Side view Column- beam moment connection. Front view
7 8 9 Comm: 216050
Date: 12/30/2022
Drawn:
Check: North

SECTIONS AND
DETAILS
S

Scale: As indicated

PERMIT SET
NOT FOR CONSTRUCTION S3.05
 Winneshiek
3/8" BENT PLATE WITH 4" VERTICAL TYPE 6" TO INSIDE FACE
Expansion and
SEE PLAN LEG X HORIZONTAL LEG FROM FACE OF STUD
TO CENTERLINE OF BEAM. SEE PLAN FOR
SEE PLAN SEE PLAN L4X3X1/4 CONT, LLH TOP AND BOTTOM
OF STUDS, SEE PLAN
Renovation
DIMENSION. L4x3x1/4 CONT, LLH WELD DECK TO ANGLE PER DECK FASTENER DETAIL L4X3X1/4 CONT, LLH TOP AND BOTTOM
WELD DECK TO ANGLE PER
WELD DECK TO BEAM/ANGLE DECK FASTENER DETAIL
JOIST SUPPLIER TO DESIGN TOP ANGLE: L4X3X3/8 WELD WELD DECK TO ANGLE PER DECK FASTENER DETAIL 901 Montgomery St
PER DECK 4/S4.00 EXTEND JOIST TO WITHIN 2" FROM FACE OF STUD FOR BRACE FORCE ANGLE TO DECK PER DECK
VERTICAL COMPONENT OF 1/4 FASTENER DETAIL; Decorah, IA 52101
+/- 2500 LBS ASD SEE PLAN LOCATION (*)
COMBINATION.
3/16 2@12
3/16 2@12
3/16 2@12 216051
CONNECTION OF STUDS TO 3/16 2@12 Winneshiek Medical
ANGLE BY STUD SUPPLIER, TYP.
Center
CONNECTION OF STUDS TO CONNECTION OF STUDS TO L3X3X1/4 TO JOIST TOP CONNECTION OF STUDS TO Decorah, IA 52101
ANGLE TO ALLOW FOR ANGLE TO ALLOW FOR CHORD PANEL POINT ANGLE BY STUD SUPPLIER, TYP.
@10' OC MAX. 3/16''
VERTICAL MOVEMENT. VERTICAL MOVEMENT.
3/16''
1/4 1/4

IA STEEL STUD WALL, STEEL STUD WALL, BEAM CENTER LINE

1/4
3/16
3/16 1/4
JOIST SUPLIER TO DESIGN
FOR BRACE FORCE
EXTEND JOIST 1'' PAST 3/16 HORIZONTAL COMPONENT
SEE ARCH DRAWINGS SEE ARCH DRAWINGS 5/16"
3/16 OF +/- 2500 LBS ASD
STEEL STUD WALL, SEE ARCH GUSSET
STEEL STUD WALL, SEE ARCH COMBINATIONS.
DRAWINGS. STUD SUPPLIER TO PLATE 5/16" GUSSET PLATE
DRAWINGS. STUD SUPPLIER TO L3X3X1/4 TO JOIST TOP
JOIST BRIDGING TO BEAM´S TOP DESIGN STUDS FOR HORIZONTAL JOIST BRIDGING TO BEAM´S TOP DESIGN STUDS FOR HORIZONTAL
REACTION FROM GLAZING. CHORD PANEL POINT
FLANGE AS REQUIRED BY SUPPLIER FLANGE AS REQUIRED BY SUPPLIER REACTION FROM GLAZING. @10' OC MAX.
3/16" 2"@12" 5/16" GUSSET PLATE
3/16" 2"@12"
GLAZING SEE ARCH. GLAZING SEE ARCH.

Roof edge beams to stud walls. Roof edge beams to stud walls Roof edge beams to stud walls and glazing. Roof edge beams to stud walls and glazing.
1 2 3 4

JOIST SUPPLIER TO DESIGN

FOR BRACE FORCE DIM 'S'
DIM 'S' DIM 'X' ANGLE 'A' ANGLE 'B'
JOIST SUPPLIER TO DESIGN FOR TOP ANGLE: L4X3X3/8 WELD HORIZONTAL COMPONENT 3/16 CENTERLINE
BRACE VERTICAL COMPONENT ANGLE TO DECK PER DECK OF +/- 2500 LBS ASD ANGLE SPLICE 0'-6" 0'-4" L3x3x1/4 L3x3x1/4
COMBINATION. CENTERLINE JOIST OR PURLIN
OF +/- 2500 lbs ASD COMBINATION. FASTENER DETAIL; 3/16 EACH END 0'-6" 4'-8" L4x3x1/4 L4x3x1/4
SEE PLAN LOCATION (*) a a W ROOF DECK SPAN DIRECTION 6'-10" 0'-4" L3x3x1/4 L5x3x1/4
1/4
BENT PLATE MIN LAP MIN LAP JOIST TOP CHORD OR PURLIN 0'-6" 0'-4" L3x3x1/4 L3x3x1/4
ACCORDING TO TABLE TOP FLANGE 6'-10" 4'-8" L5x3x1/4 L5x3x1/4

4 FRAMING ANGLE (TOP OF

ANGLES FLUSH WITH TOP OF
5/16" GUSSET PLATE BEAMS OR JOISTS). SEE
SCHEDULE FOR SIZES.
CONT EDGE ANGLE, SEE
SECTIONS FOR SIZE AND
L3X3X1/4" TO JOIST TOP CHORD THICKNESS TYP
3/16 COORDINATE SIZE AND
2 SIDES TYP PANEL POINT AND BOTTOM FLANGE LOCATION OF OPENINGS WITH 3/16
3/16 3/16

DIM. 'X'
OF BEAM. PROFILE BENT PLATE SIZE a(in) W(in) ARCH AND MECH PRIOR TO
3/16 SEE PLAN LOCATION (*) FABRICATION DIM. 'Y'
3/16
2 SIDES TYP L6x6x3/8 5x5x3/8 9 1/4
3/16 3/16 TYP 5/16" GUSSET PLATE L4x3x1/4 2x2x3/8 4 3/16 4 CLIP ANGLES L4X4X1/4X0'-5" (PLACE
3/16 1/4 C 2022 Quetica Professional Engineers, Inc.
1/4" ABOVE FRAMING ANGLES) TIGHT
L3x3x1/4 2x2x3/8 4 3/16 All rights reserved.
5/16" GUSSET PLATE TO TOP EDGE OF JOIST OR BEAM. This document is an instrument of service and is the property of
ANGLE 'A' Quetica Professional Engineers, Inc. and may not be used or copied
JOIST BRIDGING TO BEAM´S TOP L2 1/2x2 1/2x5/16 2x2x5/16 3 3/16 without prior written consent.

FLANGE AS REQUIRED BY SUPPLIER AT JOIST FRAMING-LOCATE CLIP

1/4 ANGLES AT TOP CHORD PANEL TYP
LATERAL BRACE: 3/16
L3X3X1/4 TO JOIST TOP CHORD. POINTS OR PROVIDE STIFFENER
SEE PLAN LOCATION (*) PER SPECIFICATIONS. ANGLE 'A'
MAY BE OMITTED WHEN THE ANGLE 'B' TYP
Lateral bracing for roof beam. Angle splice. Detail DIMENSION 'Y' IS 6" OR LESS.
6 7
Lateral bracing for roof beams.
5

Opening in roof deck. Detail

8

ATTACH ALL CONCENTRATED LOADS (PIPING, MECH, ROOFTOP

EQUIP CURBS, ETC) TO THE JOIST WITHIN 4" OF THE JOIST PANEL
POINT OR PROVIDE STIFFENER ANGLES AS SHOWN. FOR PIPING
EXCEEDING 20 PLF OR EQUIVALENT GROUPINGS, NOTIFY THE
STRUCTURAL ENGINEER PRIOR TO INSTALLATION.

CONNECTION OF STUDS TO CONNECTION OF STUDS TO

ANGLE BY STUD SUPPLIER, TYP. ANGLE BY STUD SUPPLIER, TYP.
TYP
PROVIDE HSS 2 1/2 X 2 1/2 X 1/4 ON 1/8
BEAM BETWEEN JOIST FOR DECK
3/16 2@12 3/16 2@12 SUPPORT. SEE DECK FASTENER
DETAIL FOR DECK ATTACHMENT.
SEE PLAN VIEW KEY NOTE (2)
STIFFENER
2@12 2@12 ANGLES
2-L2X2X1/8
1/4" 1/4" 2@12 2@12
ROOF DECK DIRECTION VARIES, SEE
4"
PLAN.
MAX
4" MAX 4" MAX SPLIT DECK AS NECESARY TO
4" FACILITATE ATTACHMENT TO
GIRDER.
MAX

STIFFENER ANGLES
2-L2X2X1/8

PIPE OR OTHER EQUIPMENT

PROVIDE HSS 2 1/2 X 2 1/2 X 1/4 ON NOTE: COORDINATE HANGING BEAM

BEAM BETWEEN JOIST FOR DECK LOAD LOCATIONS WITH
SUPPORT. SEE 4/s4.00 FOR DECK PIPES EXCEEDING 10 PLF PARALLEL TO JOIST SHALL BE ARCHITECTURAL, MECHANICAL,
ATTACHMENT. CENTERED BETWEEN JOIST AND A SPREADER MEMBER AND ELECTRICAL DRAWINGS.
SEE PLAN VIEW KEY NOTE (2) INSTALLED. FOR PIPING EXCEEDING 20 PLF OR
EQUIVALENT GROUPINGS NOTIFY THE STRUCTURAL
ENGINEER PRIOR TO INSTALLATION. I hereby certify that this plan, specifcation or report was
prepared by me or under my direct supervision and that I
Roof deck fastening. Section Special HSS for deck fastening. Section Concentrated Loads on Joist. Side view Steel roof beam. am a duly Licsened Professional Engineer under the laws
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

9 10 11 12 of the state of Minnesota.

Katherine Russell
Date 12/30/2022 Lic. No. P27101
2"
L3X4X1/4 CONT SEE EXISTING SEE PLAN BENT PLATE 3/8" X CONT WITH 4" VERTICAL LEG AND Revisions
ANGLE SPLICE DETAIL. SEE PLAN GRID STRUCTURE HORIZONTAL LEG 2" FROM EXISTING STUDS
LONG BEARING JOIST SEE PLAN Description Date Num
WELD DECK ACCORDING TO TO CENTER LINE OF BEAM
3/16 3/16 WELD DECK TO ANGLE PER 4/S4.00
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

DECK FASTENER DETAIL 3/16 2@12

SEE PLAN WELD DECK TO BEAM/ANGLE
CONNECTION OF STUDS TO L3X4X1/4 CONT SEE 10/S3.04 L 2 ½ x 2 ½ x 5/16 PER DECK 4/S4.00
ANGLE BY STUD SUPPLIER FOR ANGLE SPLICE. WELD DECK LONG BEARING JOIST x CONT. WELD
ACCORDING DECK FASTENER DETAIL DECK TO ANGLE
AS PER 4/S4.00 L 6 x 6 x 3/8 x CONT.
L3x3x1/4
3/16 1" PAST. CL OF BM 3/16 2@12
L3X3X1/4 CONT.
CONC. CURB, SEE ARCH.
3/16
5/16 BENT PLATE TOP AND BOTTOM, WELD
28/12/2022 10:51:53

DECK TO PLATE ACCORDING FASTENER

3/16 2" DECK WELD
JOIST SUPLIER TO DESIGN DETAIL
TO STEEL BEAMS Comm: 216050
3/16 FOR BRACE FORCE PER 4/S4.00
HORIZONTAL COMPONENT Date: 12/30/2022
CONNECTION OF STUDS TO
1/4 OF +/- 2500 LBS ASD BENT PLATE BY STUD SUPPLIER, 1/4" BENT PLATE WITH 2 1/2" Drawn:
1" GAP

L3x3x1/4 COMBINATIONS. VERTICAL LEG X HORIZONTAL LEG

TYP. Check: North
JOIST SUPLIER TO DESIGN FROM FACE OF STUD TO END OF JOIST
5/16" GUSSET PLATE L3X3X1/4 TO JOIST TOP FOR BRACE FORCE x WELDED TO HSS; SEE DETAIL 3/S3.05
EXISTING STRUCTURE CHORD PANEL POINT HORIZONTAL COMPONENT
EA. JOIST 3/16" 2"@12" OF +/- 2500 LBS ASD
COMBINATIONS. JOIST
STEEL BEAM JOIST BRIDGING TO
BEAM´S TOP FLANGE AS
SECTIONS AND
5/16" GUSSET PLATE L3X3X1/4 TO JOIST TOP W/ STD. CONN.,
NOTE: NON CONTINUOUS ANGLES TO BE
ATTACHED TO EVERY JOIST
SUPPORTED IN THE GIRDER. PLATE
CHORD PANEL POINT
EA. JOIST
L6 & L 2 ½
3/16 2@12@HSS MAIN BEAM SEE PLAN REQUIRED BY SUPPLIER
DETAILS
S
bf= 6 1/2" GAP CL BEAM TO 2" FROM STUD 9"

Roof connection with existing structure Roof edge beams. Section 4 Change in roof deck type. Roof connection with existing structure
13 14 15 16

Scale: As indicated

PERMIT SET
NOT FOR CONSTRUCTION S3.06
 Winneshiek
B.9 D.2 5.0 3.9 3.9 5.0 A.9 _______
9
B.9 Expansion and
_______
9
S3.09
5
S3.09
Renovation
OPP
SEE PLAN S3.09 14'-7 7/8" 14'-8 1/8"
14'-2 7/8" 14'-3 1/8"

ROOF LEVEL ROOF LEVEL ROOF LEVEL

PH ROOF 901 Montgomery St
SEE PLAN SEE PLAN SEE PLAN
SEE PLAN Decorah, IA 52101

5 216051
S3.09
Winneshiek Medical
Center
HS
Decorah, IA 52101
T= S8

HS
6
6 C= X8

/1

6
T=
5/1

E)

HS
X5

E)
/1
S7

T=
X5
E) 33

AT

C
X

X5
/16

AT

S7
X7 X8 K

X7

C
AT

=1
IM
(U

X7

=1
8

IM

X7
X5
S7

7K
S IM LT
LT

S7
HS

7K
LT

LT

X5
/1
IM
HS

(U
(U
(U
IA

HS

(U
AT

/1
(U
LT
7K

6K E)

6
LT
7K
IM
=3
=1

_______
4

IM
TYP.

=1
_______

AT
3 C
C

T=

AT
_______

C
T=

S3.09 10

E)
TYP. OPP S3.09

T=

E)
_______
10 S3.09 _______
3
S3.09
6 S3.09 OPP
S3.09
TYP.
_______
4 _______
10
MAIN LEVEL MAIN LEVEL MAIN LEVEL S3.09
S3.09
SEE PLAN SEE PLAN SEE PLAN

ROOF LEVEL
6 OPP SEE PLAN
S3.09

HS HS
/16 T= S7 /16 S8
X5 ) X7 X5 X8
7X 7
A TE C= X5 S8
X 8
E)
T=
C= X5
/16 TYP.
53 AT _______
S IM K /16 HS 54 10
HS LT (U TIM K( S3.09
K
( U LT OPP _______
1 K (UL UL
TIM
OPP _______ IM 4
2
= 53 AT _______
2 S3.09 C=
6 AT
E)
S3.09 C E) T=
T= S3.09 _______
1
S3.09

HS
6
/1

T=
E)

S7
X5

AT

C=

X7
X7
LOWER LEVEL LOWER LEVEL LOWER LEVEL

IM

60

X5
S7

LT

/1
HS
SEE PLAN SEE PLAN

(U
SEE PLAN

(U

6
LT
_______ _______

K
7 7 SIM

60

IM
S3.09 S3.09 OPP TYP.

C=

AT
_______
10 OPP

T=

E)
S3.09

BRACING SECTION 1 BRACING SECTION 2 BRACING SECTION 3

1 2 3 MAIN LEVEL
SEE PLAN
TYP.
_______
10
S3.09
3.1 2.3 4'-8" 4'-7 3/4"
SEE PLAN

HS
ROOF LEVEL

/1

E)
C 2022 Quetica Professional Engineers, Inc.

T=
X5

AT

S7
All rights reserved.

C=
X7
SEE PLAN

IM
_______ This document is an instrument of service and is the property of

X7
9

90
S7
B.9 A.9

LT
Quetica Professional Engineers, Inc. and may not be used or copied

X5
S3.09

K
HS
without prior written consent.

(U

/1
(U

6
5

LT
14'-8 1/8" 14'-7 7/8"

90

IM
S3.09

C=
PH ROOF

AT
T=
OPP _______
2 _______
2

E)
SEE PLAN S3.09 S3.09

LOWER LEVEL
/ 16 ) SEE PLAN
8 X5 TE
X A
S8 IM
HS ULT
(
5K BRACING SECTION 4
C=
3 4
T=
_______
8
S3.09
6
/1

E)

HS
X5

AT

T=
X7

S7
IM

C
S7

=9

X7
LT

K
MAIN LEVEL
HS

X5
(U

(U

/1
9K

LT
SEE PLAN

6
C=

IM
T=

AT
E)
TYP _______
13
S3.09 _______
13 SIM
S3.09

HS
S8
T= X8
C= X5
70 /16 ROOF LEVEL
K(
UL
TIM SEE PLAN
AT
E)
_______
1
S3.09

LOWER LEVEL
SEE PLAN

BRACING SECTION 5 BRACING SECTION 6

5 6

3.0 2.3
5
S3.09
B.9 A.9 I hereby certify that this plan, specifcation or report was
_______
9 prepared by me or under my direct supervision and that I
SEE PLAN
14'-8 1/8" S3.09 14'-7 7/8" am a duly Licsened Professional Engineer under the laws
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

of the state of Minnesota.

ROOF LEVEL ROOF LEVEL
SEE PLAN SEE PLAN
Katherine Russell
Date 12/30/2022 Lic. No. P27101

Revisions
Description Date Num
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

6
/1 )
HS
6

5 TE
/1

T=
E)

X
S7
X5

8 A
C
AT

X
X7

M
=2
X7

S8 TI
IM

X5
1K
S7

S L
LT

H (U
/1
HS

(U
(U

K
LT

3
1K

3
IM

C=
=2

AT

= TYP.
C

T TYP. _______
4 _______
E)
T=

10 OPP
_______
3 _______
10 S3.09 S3.09
S3.09 6 OPP S3.09
28/12/2022 10:52:00

S3.09
Comm: 216050

MAIN LEVEL MAIN LEVEL Date: 12/30/2022

SEE PLAN SEE PLAN Drawn:
Check: North

HS
SECTIONS AND
6 S7

S 8X
8X 5/1
M AT
E)
X 5/1
6
)
T=
C=
62
K
X7
X5
/16
DETAILS
HS I 7 TE
LT 7X (U

S (U S A LT
HS IM IM
1K LT AT
C =7 OPP _______
11 (U E)
T= 2K
OPP _______
1 S3.09
C =6 _______
11
S3.09 T= S3.09

CLINIC LOWER LEVEL CLINIC LOWER LEVEL

SEE PLAN SEE PLAN
Scale: 1/4" = 1'-0"

PERMIT SET
7
BRACING SECTION 7
8
BRACING SECTION 8
NOT FOR CONSTRUCTION S3.07
 Winneshiek
11.86 C.22 B.22 Expansion and
Renovation
B.22 C.22 11.86 26'-9"

3'-5 1/4" 3'-5 1/4"

901 Montgomery St
Decorah, IA 52101

13'-4 5/8" 13'-4 3/8" 13'-4 3/8" 13'-4 5/8" 216051

Winneshiek Medical
Center
Decorah, IA 52101

PH ROOF LEVEL AB PH ROOF LEVEL AB PH ROOF LEVEL AB PH ROOF LEVEL AB

IA _______
9
S3.09
SEE PLAN
_______
9
S3.09

SEE PLAN
WP
PH ROOF LEVEL PH ROOF LEVEL PH ROOF LEVEL PH ROOF LEVEL
PENTHOUSE PLAN
WP - ELECTRICAL
W21X44
125' - 8"

E)

T=
COLUMN, SEE PLAN

COLUMN, SEE PLAN

COLUMN, SEE PLAN

COLUMN, SEE PLAN

AT

C
=
HS

IM

15
E)

LT
S

KI
6X AT

(U

PS
16 6X M T=

PS
5/ TI

(U
5/ L C=

KI
X 16 U

LT
6 ( 15

15
6X PS

IM
KI
16

=
I

AT
S OPP PS

C
K 5/
HS 15

T=
HS

E)
_______
13 6X (U
S3.09 _______
13 C= 6X S LT
S3.09 T= S 6X
6X
IM
AT OPP
HS 5/ E) _______
13
_______
13 16 S3.09
S3.09

ROOF LEVEL AB
ROOF LEVEL WP WP ROOF LEVEL
ROOF AB
LEVEL ROOF LEVEL AB
ROOF LEVEL WP WPROOF LEVEL
ROOF AB
LEVEL
SEE PLAN SEE PLAN

W21X62
ELEC UL
111' - 8"

FRAME ON GRIDLINE FRAME ON GRIDLINE 2.22

1 2 C 2022 Quetica Professional Engineers, Inc.
All rights reserved.
This document is an instrument of service and is the property of
Quetica Professional Engineers, Inc. and may not be used or copied
without prior written consent.

2.96.
2.96 3.22
2.22 3.22

13'-11 1/2"

5 2'-8 1/2"
WP
S3.09
PH ROOF LEVEL AB 5
S3.09
SEE PLAN

SEE PLAN
1'-1 1/4"

PH ROOF LEVEL
WP
PH ROOF LEVEL
PENTHOUSE PLAN
- ELECTRICAL PENTHOUSE PLAN
125' - 8" - ELECTRICAL
125' - 8"
COLUMN, SEE PLAN

COLUMN, SEE PLAN

COLUMN, SEE PLAN

TE

COLUMN, SEE PLAN

A
E)

IM
LT
AT

(U I hereby certify that this plan, specifcation or report was

IM

S prepared by me or under my direct supervision and that I

LT

_______
13
K IP /16
X5
(U

S3.09 15 6
am a duly Licsened Professional Engineer under the laws
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

PS

C= 6X of the state of Minnesota.

T=
KI

S S
15

H
16
=
C

5/
T=

6X
6X

Katherine Russell
SS

Date 12/30/2022 Lic. No. P27101

H

_______
13 Revisions
S3.09 Description Date Num
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

WP
ROOF LEVEL AB
ROOF LEVEL
SEE PLAN

ROOF LEVEL AB ELEC UL

ROOF LEVEL
28/12/2022 10:52:03

111' - 8"
Comm: 216050
SEE PLAN Date:
WP 12/30/2022
Drawn:
Check: North

ELEC UL
111' - 8" SECTIONS AND
DETAILS
FRAME ON GRIDLINE B.22 FRAME ON GRIDLINE D.22
3 4
S

Scale: As indicated

PERMIT SET
NOT FOR CONSTRUCTION S3.08
 Winneshiek
GRID
Expansion and
GRID
Renovation
GRID 1/4"

1/4" 901 Montgomery St

L 1"
M
TY IN
Decorah, IA 52101
STEEL COLUMN, P ,

L
STEEL COLUMN,

IN
SEE SCHEDULE 1/4
216051

M
SEE SCHEDULE 3 SIDES TYP

L
1/4

AX
1/4" ≥L
Winneshiek Medical

M
TYP
1/2'' GUSSET PLATE 1/4" ≥L

L
1/2" GUSSET PLATE
Center

L
3/8" STIFFENER 1/4"
2 SIDES
EA. SIDE, TYP
TYP Decorah, IA 52101
1/4"

1" GAP MIN

BASE PLATE; SEE SCHEDULE HS 1/4"
HS WP 1/4"
1" GAP TYP S TYP

1" GAP MIN TYP

S Lx TYP
Lx Lx 1/4"
Lx Th WP 1/4"
th STIFFENER 3/8"

YP
M
IN

"T
IA 1/2" GUSSET M L

.1
IN

IN
PLATE L

M
M 3/8" STIFFENER
IN

1" TYP
L M EA. SIDE, TYP

M
AX

IN
1/4" L

"
.1
1/4" ≥L HS

IN
2 SIDES L S
Th Lx

M
1/4" IN
1/4" ≥L TYP Lx M Lx
1/4" ≥L Lx 1/4" ≥L
T h
1/4" ≥L S
WP HS

TY IN
TYP DOUBLE ANGLE OR SINGLE PLATE TYP

M
TYP WP

P
1/4" ≥L DOUBLE ANGLE OR SINGLE PLATE CONNECTION. 1/4" ≥L

1"
1/4" ≥L CONNECTION SEE S4.00
SEE S4.00
1/2" GUSSET PLATE

L
L
COLUMN BASE PLATE,
1/4" ≥L SEE SCHEDULE
1/4" ≥L
1/4" ≥L
1/4" ≥L

Braced frame connection. Foundation level. Braced frame connection. Foundation level. Braced frame connection. Intermediate level. K Braced frame connection. Intermediate level 1.
1 2 3 4

GRID
GRID
DOUBLE ANGLE OR SINGLE PLATE.
1/4" ≥L SEE PLAN
1/4" ≥L
3/8" STIFFENER EA. SIDE, TYP.
1/4 HSS LxLxTh
1/2'' GUSSET PLATE 3 SIDES
TYP 1/4" ≥L
GRID
1" GAP MIN TYP

1/4 TYP M
I L
1/4" ≥L TY N 1

1" GAP MIN TYP

P "
WP

L
1/4" ≥L

AX
TYP

M
1/4" ≥L 1/4" ≥L 1/4" ≥L
TYP
1/4" ≥L

1" GAP MIN

1/4" ≥L

1" GAP MIN

WP 1/2" GUSSET PLATE C 2022 Quetica Professional Engineers, Inc.
1/4 ≥L All rights reserved.
1/2 GUSSET WP 1/4" ≥L This document is an instrument of service and is the property of
TYP Quetica Professional Engineers, Inc. and may not be used or copied
PLATE TYP 1/4 ≥L without prior written consent.

L
L 1/4" ≥L

IN
Th AX 1/4"

M
Lx M
TYP
Lx L
WP
S IN 1/4"
HS

L
M 1/4" ≥L 1"

AX
TY MIN

M
M
1/4" ≥L P 3/8'' GUSSET PLATE

AX

L
1/4

IN
L
YP 1/2" GUSSET PLATE

M
1/4" ≥L TYP

h
"T

T
1/4 "

IN
TYP 1

Lx
IN
. 1/4" ≥L .1

Lx
1/4" ≥L M HSS LxLxTh TYP IN P

M
1/2" GUSSET PLATE M TY

AX
HS
1/4" ≥L

L
HSS LxLxTh

M
IN
L
L

L
DOUBLE ANGLE OR SINGLE PLATE DOUBLE ANGLE OR SINGLE PLATE DOUBLE ANGLE OR SINGLE PLATE DOUBLE ANGLE OR SINGLE PLATE
CONNECTION CONNECTION. L CONNECTION CONNECTION.
SEE S4.00 SEE S4.00 SEE S4.00 SEE S4.00

Braced frame connection. Roof level. Braced frame connection. Intermediate level. K Braced frame connection. Intermediate level 2. Braced frame connection. Intermediate level.
5 6 7 8
GRID

GRID

1/4
3 SIDES TYP
1/4 1/4" ≥L

1/4" ≥L STEEL COLUMN,

1/4" L SEE SCHEDULE
3/8" STIFFENER

T h
1"
L

Lx
EA. SIDE, TYP M
AX

1/4"
L

Lx
IN TY IN
P ,
M

S
M
1" GAP MIN

HS
WP

L
1/4" 1/2'' GUSSET PLATE
1/4" ≥L 1/4" ≥L
2 SIDES TYP TYP
1/4" M TYP
IN 1/4" ≥L 1/4" ≥L 1/2" GUSSET PLATE
L
1"
3/8" STIFFENER M
IN
1" TYP

EA. SIDE, TYP 1/4" ≥L STIFFENER 3/8" 1"

L
M

1" GAP MIN

IN

HS
1/4" ≥L S
HS WP Lx
L S L xT
Th IN Lx h
x Lx M Lx BASE PLATE; SEE SCHEDULE
L 1/4" ≥L Th
S M
HS
TY IN

TYP AX
M

"
L
P

.1
1/4" ≥L
1"

1/4" ≥L

IN
NOTES

M
GUSSET PLATE 1/2" 1/4" ≥L 1/4" ≥L
L
L

TYP WP I hereby certify that this plan, specifcation or report was

1/4" ≥L 1. MINIMUM GAP HSS TO BEAM FLANGE/WEB/PLATE 1". TYPICAL. prepared by me or under my direct supervision and that I

1" GAP MIN

2. ALL CONNECTIONS FIELD WELDED MUST BE RE-PAINTED ON SITE. am a duly Licsened Professional Engineer under the laws
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

DOUBLE ANGLE OR SINGLE PLATE 3. SEE BEAM TO COLUMN DOUBLE ANGLE OR SINGLE PLATE of the state of Minnesota.
DOUBLE ANGLE OR SINGLE PLATE CONNECTION. CONNECTION IN DRAWING S4.00.
CONNECTION SEE S4.00 4. SEE BASE PLATE ANCHOR BOLTS DETAILING IN DRAWING S4.00.
SEE S4.00 GUSSET PLATES TO BASE PLATE CONNECTION ACCORDING TO THIS
DRAWING. Katherine Russell
5. ALL BOLTED CONNECTION FOR VERTICAL BRACING SLIP CRITICAL; SEE Date 12/30/2022 Lic. No. P27101
PLANS FOR INDICATION.
6. ALL STIFFENERS WITH SNIP 3/4"x3/4".
7. SEE 12/S3.09 FOR TYPICAL BRACE WELDING TO GUSSET Revisions
K Braced frame connection. Roof Level. Braced frame connection. Intermediate level. Braced frame connection. Foundation level. Description Date Num
9 10 11
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

T h
, TYP

MIN L,
Lx

TYP
Lx
28/12/2022 10:52:16

1/4" ≥L
1" MIN

HS

Comm: 216050
1/4" ≥L 1/4" ≥L Date: 12/30/2022
TYP
1/4" ≥L Drawn:
HSS Lx
LxTh
L

Check: North
AX

1/2" GUSSET PLATE

M

1/4" ≥L
ROOF LEVEL AB
1/4" ≥L
SECTIONS AND
1/4" ≥L
TYP
WP
DETAILS
1/4" ≥L

S CAP PLATES WELDED

TO GUSSET AND HSS

GUSSET PLATE
BEAM TO BEAM CONNECTION; SEE PLAN

Scale: As indicated

12
Typical HSS Site Welding
13
Bracing connection at transfer beam PERMIT SET
NOT FOR CONSTRUCTION S3.09
 1'-2"
4 dB (min 2 1/2") Winneshiek
BOLTED - DOUBLE ANGLE CONNECTION TABLE

BEAM # OF BOLT Ø Rn Ø Rn TYPICAL HOOK

Expansion and
2" 2" 2" 2" 2X2X1/4" WASHER PLATES SEE REMARKS
Renovation

6 dB
TYP COLUMN BASE PLATES SIZE ROWS COPED UNCOPED for bars #3 to #8
a SCHEDULE
WITH OVERSIZED HOLES

dB
2" 2"
W8x10-W8x24, WEB STIFFENER REQUIRED FOR DOUBLE
W10x12-W10x22, 2 18 30 COPED BEAMS IF COPE LENGTH >0'-3''
W12x14-W12x26 (MAX CAPACITY=5K W/OUT STIFFENER)
W8x28-W8x40, WEB STIFFENER REQUIRED FOR DOUBLE 901 Montgomery St
W10x26-W10x49, 2 27 44 COPED BEAMS IF COPE LENGTH >0'-3'' Decorah, IA 52101
CLASS "A" TENSION LAP SPLICE TABLE

2" 2"
W12x30-W12x53 (MAX CAPACITY=14K W/OUT STIFFENER)

≥ 3/4" TYP
LEVELING NUT, AT PROVIDE UPSET THREADS WEB STIFFENER REQUIRED FOR DOUBLE
CONTRACTOR'S TYPICAL AT TOP AND BOTTOM OF ROD
W8x48-LARGER,
2 38 46 BAR fc (psi) 216051
2" 2" W10x49-LARGER COPED BEAMS IF COPE LENGTH >0'-3''
OPTION (MAX CAPACITY=19K W/OUT STIFFENER) SIZE 2500 3000 3500 4000 5000 6000 7000 8000
WEB STIFFENER REQUIRED FOR DOUBLE
COPED BEAMS IF COPE LENGTH >0'-3''
#3 1´-6" 1´-5" 1´-4" 1´-3" 1´-1" 1´-0" 1´-0" 1´-0" Winneshiek Medical
W14x22 3 32 60
Center

2" 2"
(MAX CAPACITY=22K W/OUT STIFFENER) #4 2´-0" 1´-10" 1´-9" 1´-7" 1´-5" 1´-4" 1´-3" 1´-2"
SEE ELEVATIONS FOR W14x26-W14x48, WEB STIFFENER REQUIRED FOR DOUBLE #5 2´-6" 2´-4" 2´-2" 2´-0" 1´-10" 1´-8" 1´-6" 1´-5"
GUSSET PLATES W16x26-W16x45, 3 43 65 COPED BEAMS IF COPE LENGTH >0'-3''
Decorah, IA 52101
#6 3´-0" 2´-9" 2´-7" 2´-5" 2´-2" 2´-0" 1´-10" 1´-9"

EMBEDMENT LENGTH
CONNECTIONS. BASE W18x35-W18x50 (MAX CAPACITY=25K W/OUT STIFFENER)
WASHER AND NUT ≥ 3/4" TYP PLATE SIZE TO BE #7 4´-5" 4´-0" 3´-9" 3´-6" 3´-2" 2´-10" 2´-8" 2´-6"
SEE SCHEDULE
ADJUSTED TO FIT GUSSET W12x58-LARGER,
WEB STIFFENER REQUIRED FOR DOUBLE #8 5´-0" 4´-7" 4´-3" 4´-0" 3´-7" 3´-3" 3´-0" 2´-10"
PLATE W14x53 LARGER,
SCHEDULE
COLUMN, SEE SCHEDULE 3 61 94 COPED BEAMS IF COPE LENGTH >0'-3''
W16x50-LARGER,

B
D A1 B DIA
(MAX CAPACITY=26K W/OUT STIFFENER)

IA DIA
3/4" 2" 1'-0" 1'-3/4"
1" 3" 1'-4" 2'-1/4"
ANCHOR
RODS, SEE
W18x55-LARGER

ALL W21 AND W24 4 82 122

WEB STIFFENER REQUIRED FOR DOUBLE
COPED BEAMS IF COPE LENGTH >0'-3''
CLASS "B" TENSION LAP SPLICE TABLE
Column base plate. Detail (MAX CAPACITY=76K W/OUT STIFFENER) BAR fc (psi)
SCHEDULE
3 ALL W27 AND W30 7 229 229 SIZE
A TYPICAL ANCHOR ROD. SEE
BASE PLATE, 2500 3000 3500 4000 5000 6000 7000 8000
SEE
PLAN NOTES AND COLUMN UNLESS NOTED OTHERWISE: #3 1´-11" 1´-10" 1´-8" 1´-7" 1´-5" 1´-4" 1´-2" 1´-2"
5/8'' PLATE WASHER SCHEDULE
SCHEDULE NOTES "ASSUMES AISC STANDARD CONNECTION CONFIGURATION.
NUTS PER ROD TOF SEE PLAN #4 2´-7" 2´-5" 2´-3" 2´-1" 1´-11" 1´-9" 1´-7" 1´-6"
1. ALL BOLTS 3/4''Ø A325-N.
BOTTOM 2. ALL ANGLES MINIMUM 5/16' THICK ASTM A36. ALL BEAMS ASTM A992. #5 3´-3" 3´-0" 2´-9" 2´-7" 2´-4" 2´-2" 2´-0" 1´-10"
NOTE: ANCHOR BOLTS AT DETAIL MUST BE 3. FOR COPED BEAM Leh=1 3/4'' MINIMUM. Lev=1 3/4'' MINIMUM (PARAMETERS PER AISC 13TH #6 3´-11" 3´-7" 3´-4" 3´-1" 2´-10" 2´-7" 2´-4" 2´-3"
F1554 GR55 STEEL MIN 2" NON- EDITION).
SHRINK GROUT MAXIMUM COPE LENTH=5''. MAXIMUM COPE DEPTH 20% OF BEAM DEPTH. #7 5´-8" 5´-3" 4´-10" 4´-6" 4´-1" 3´-9" 3´-5" 3´-3"
4. HORIZONTAL SHORT SLOTTED HOLES PERMITTED IN BEAM WEB AND OUTSTANDING ANGLE LEGS. #8 6´-6" 6´-0" 5´-6" 5´-2" 4´-8" 4´-3" 3´-11" 3´-8"
5. COORDINATE ANGLE LENGTHS WITH DRAWINGS AND COORDINATE BOLT LOCATIONS FOR
2X2X1/4" WASHER PLATES SEE ERECTION PURPOSES.
CONCRETE PILE CAP, TYP COLUMN BASE PLATES 6. BEAMS REQUIRING ADDITIONAL BOLTS WILL BE NOTED ON THE DRAWINGS THUS: 'DA-X' NOTES:
a SCHEDULE
SEE PLAN AND SCHEDULE WITH OVERSIZED HOLES (X=NUMBER OF ROWS OF BOLTS). 1. THESE TABLES SHOW LENGTHS FOR PLAIN, BOTTOM ASTM A615 GRADE 60 BARS IN NORMAL
7. CAPACITIES SHOWN REPRESENT MINIMUN CONNECTION CAPACITY FOR RANGE OF SIZES GIVEN. WEIGHT CONCRETE, MEETING THE SPACING AND COVER LIMITATIONS GIVEN BELOW.
MULTIPLY THESE LENGTHS BY ALL OF THE APPLICABLE FACTORS GIVEN FOR OTHER

d/5 MAX
Typical anchor. Detail Column base plate. Side and plan view CONDITIONS. SPECIFIC EMBEDMENT, LAP, OR PROJECTION LENGTHS SHOWN ON DRAWINGS
1 2 GOVERN OVER THESE TABLES.

1 3/4"
1 3/4" MIN

MIN
1 3/4" MIN
2. SPACING AND COVER REQUIREMENTS.

4"
a. CLEAR SPACING BETWEEN BARS AT SPLICE ≥2db AND CLEAR COVER ≥db OR
b. CLEAR SPACING BETWEEN BARS AT SPLICE ≥db AND CLEAR COVER ≥db AND STIRRUPS/TIES

d
PH FRAMING PLAN - PH FRAMING OVER FULL LENGTH OF SPLICE. STIRRUPS/TIES TO BE SPACED SUCH THAT:
AREA 'A' & 'B' SC1 SC2 SC3 SC4 SC5 SC6 SC7 SC8 SC9 SC10 SC11 SC12 SC13 SC14 SC15 PLAN - AREA 'A' s x n≤16 FOR #3 TIES/STIRRUPS

1 3/4"
MIN
& 'B' s x n≤32 FOR #4 TIES/STIRRUPS

d/5 MAX
1 1/4" 1 1/4" s x n≤50 FOR #5 TIES/STIRRUPS
VARIES, SEE VARIES, SEE db = BAR DIAMETER IN INCHES, s = SPACING OF TIES/STIRRUPS, n = NUMBER OF BARS
UNCOPED BEAM END COPED BEAM END
PLAN PLAN SPLICED AT A GIVEN LOCATION.
1 1/2" 1 1/2" 3. MULTIPLY GIVEN SPLICE LENGTHS BY ALL THE FOLLOWING APPLICABLE FACTORS:
SINGLE PLATE CONNECTION TABLE a. MULTIPLY BY 1.5 IF SPACING OR COVER REQUIREMENTS ARE NOT MET.
b. MULTIPLY BY 1.3 FOR TOP BARS. TOP BARS ARE DEFINED AS HORIZONTAL BARS WITH MORE
BEAM # OF BOLT Ø Rn Ø Rn T HAN 12" OF FRESH CONCRETE BELOW THE BAR.
REMARKS
W8x35

SEE ELEVATIONS FOR SIZE ROWS COPED UNCOPED c. MULTIPLY BY 1.2 FOR #3 OR #4 EPOXY COATED BARS SPACED 4" MIN OC WITH 1 1/2" MIN
GUSSET PLATES
CLEAR COVER.
CONNECTIONS. BASE W8x10-W8x24, WEB STIFFENER REQUIRED FOR DOUBLE d. MULTIPLY BY 1.31 FOR OTHER EPOXY COATED TOP BARS.
PLATE SIZE TO BE W10x12-W10x22, 2 18 25 COPED BEAMS IF COPE LENGTH >0'-3'' e. MULTIPLY BY 1.5 FOR OTHER EPOXY COATED BARS - EXCEPT TOP BARS.
ADJUSTED TO FIT GUSSET W12x14-W12x26 (MAX CAPACITY=5K W/OUT STIFFENER) f. MULTIPLY BY 1.3 FOR LIGHTWEIGHT CONCRETE.
PLATE
W8x28-W8x40, WEB STIFFENER REQUIRED FOR DOUBLE g. MULTIPLY BY fy/60 FOR BARS WITH YIELD STRESS >60 KSI.
W10x26-W10x49, 2 25 25 COPED BEAMS IF COPE LENGTH >0'-3'' 4. USE CLASS 'B' TENSION LAP SPLICES UNLESS SPECIFICALLY NOTED OTHERWISE.
ROOF LEVEL ROOF LEVEL
W12x30-W12x53 (MAX CAPACITY=14K W/OUT STIFFENER) 5. COMPRESSION LAP LENGTH, ONLY WHERE NOTED, TO BE 30db. INCREASE TO 44db FOR Fy =
75 KSI, AND 57db FOR Fy = 90KSI
114'-6'' 114'-6''
Column base plate. Detail W8x48-LARGER, WEB STIFFENER REQUIRED FOR DOUBLE C 2022 Quetica Professional Engineers, Inc.
4 W10x49-LARGER,
W12x58-LARGER
2 25 25 COPED BEAMS IF COPE LENGTH >0'-3''
(MAX CAPACITY=19K W/OUT STIFFENER)
All rights reserved.
This document is an instrument of service and is the property of
Quetica Professional Engineers, Inc. and may not be used or copied
W10x49

W10x49

W10x49

W10x49
without prior written consent.
W8x48

W8x48

W8x48

W8x48

W8x48

W8x48

W8x48

W8x48

WEB STIFFENER REQUIRED FOR DOUBLE

W14x22 3 32 42 COPED BEAMS IF COPE LENGTH >0'-3''
(MAX CAPACITY=22K W/OUT STIFFENER)
WEB STIFFENER REQUIRED FOR DOUBLE ARCHITECTURALLY EXPOSED STRUTURAL STEEL (AESS)
W14x26-W14x48,
3 42 42 COPED BEAMS IF COPE LENGTH >0'-3'' CATEGORY AESS 3 AESS 2
W14x53-LARGER
MAIN LEVEL MAIN LEVEL (MAX CAPACITY=25K W/OUT STIFFENER)
CHARACTERISTICS FEATURE FEATURE
100'-0'' 100'-0'' 2X2X1/4" WASHER PLATES WEB STIFFENER REQUIRED FOR DOUBLE ELEMENTS IN ELEMENTS NOT
SEE W16x26-W16x45,
TYP COLUMN BASE PLATES 3 45 53 COPED BEAMS IF COPE LENGTH >0'-3'' CLOSE VIEW IN CLOSE VIEW
a SCHEDULE W18x35-W18x50
WITH OVERSIZED HOLES (MAX CAPACITY=26K W/OUT STIFFENER) (<20 FT) (<20 FT)
W16x50-LARGER, 1.1 SURFACE PREPARATION TO SSPC-SP 6 X X
W8x35 4 61 63

W8x35
W18x55-LARGER
1.2 SHARP EDGES GROUND SMOOTH X X
ALL W21 AND W24 5 79 79 USE ONLY WHERE NOTED FOR W24'S
1.3 CONTINUOUS WELD APPEARANCE X X
UNLESS NOTED OTHERWISE: 1.4 STANDARD STRUCTURAL BOLTS X X
*ASSUMES AISC STANDARD CONNECTION CONFIGURATION.

4"
LOWER LEVEL LOWER LEVEL 1.5 WELD SPATTERS REMOVED X X
1. ALL BOLTS 3/4"O A325-N. PLATE WELDS 2-1/4" FULL LENGTH FILLET WELDS.
2. ALL PLATES 5/16" THICK ASTM A36. ALL BEAMS ASTM A992.
88'-5 3/8" 88'-5 3/8" 3. FOR COPED BEAMS Leh=1 3/4" MINIMUM. Lev=1 3/4" MINIMUM (PARAMETERS PER AISC 13TH 2.1 VISUAL SAMPLES OPTIONAL OPTIONAL
EDITION). MAXIMUM COPE LENGTH = 5". MAXIMUM COPE DEPTHS = 20% OF BEAM DEPTH.
2.2 ONE-HALF STANDARD FABRICATION TOLERANCES X X
4. HORIZONTAL SHORT SLOTTED HOLES PERMITTED IN BEAM WEB.
PLATE SIZE 12x12x3/4 12x12x3/4 15x12x3/4 15x12x3/4 12x12x3/4 12x15x3/4 12x12x3/4 12x12x3/4 14x10x3/4 12x12x3/4 12x12x3/4 12x12x3/4 18 1/2x12x3/4 12x12x3/4 12x12x3/4 3 1/2" 3 1/2" 5. COORDINATE PLATE LENGTH WITH DRAWINGS AND COORDINATE BOLT LOCATIONS FOR 2.3 FABRICATION MARKS NOT APPARENT X X
BASE PLATE

ERECTION PURPOSES. 2.4 WELDS UNIFORM AND SMOOTH X X

ANCHOR BOLTS 4-3/4''Ø 4-3/4''Ø 8-3/4''Ø 8-3/4''Ø 4-3/4''Ø 8-3/4''Ø 4-3/4''Ø 4-3/4''Ø 8-3/4''Ø 4-3/4''Ø 4-3/4''Ø 4-3/4''Ø 8-1''Ø 4-3/4''Ø 4-3/4''Ø 6. BEAMS REQUIRING ADDITIONAL BOLTS WILL BE NOTED ON THE DRAWINGS THUS: "SP-X"
SEE ELEVATIONS FOR (X=NUMBER OF ROWS OF BOLTS).
GUSSET PLATES 7. CAPACITIES SHOWN REPRESENT MINIMUM CONNECTION CAPACITY FOR THE RANGE OF SIZES 3.1 MILL MARKS REMOVED X
WELDING a= 3/8" a= 3/8" a= 3/8" a= 3/8" a= 3/8" a= 3/8" a= 3/8" a= 3/8" - a= 1/2" a= 1/2" a= 1/2" a= 1/2" a= 1/2" a= 1/2"
CONNECTIONS. BASE GIVEN. 3.2 BUTT AND PLUG WELDS GROUND SMOOTH AND FILLED X
DETAIL 3/S4.00 3/S4.00 4/S4.00 5/S4.00 3/S4.00 4/S4.00 3/S4.00 3/S4.00 - 3/S4.00 3/4.00 3/S4.00 4/S4.00 3/4.00 3/4.00 PLATE SIZE TO BE
3.3 HSS WELD SEAM ORIENTED FOR REDUCED VISIBILITY X
ADJUSTED TO FIT GUSSET

d/5 MAX
PLATE 3.4 CROSS SECTIONAL ABUTTING SURFACE ALIGNED X
NOTES:

1 3/4"
1 3/4" MIN 3.5 JOINT GAP TOLERANCES MINIMIZED X

MIN
1. EXTEND STRAIGHT TYPICAL ANCHOR BOLT 12" INTO CONCRETE, MINIMUM, SEE SCHEDULE AND DETAIL 1/S4.00. 1 3/4" MIN
2. PROVIDE 2" NON-SHRINK GROUT BELOW BASE PLATE. 3.6 ALL WELDED CONNECTIONS OPTIONAL
3. SEE DETAILS 1-5/S4.00 FOR ANCHOR BOLTS.
4. ANCHOR BOLTS ASTM F1554 GR55.

d
4.1 HSS SEAM NOT APPARENT X
Column base plate. Detail 4.2 WELDS CONTOURED AND BLENDED X
5

1 3/4"
MIN
4.3 SURFACES FILLED AND SANDED X

d/5 MAX
PH FRAMING PLAN - PH FRAMING PLAN -
AREA 'H' SC16 SC17 SC18 SC19 SC20 AREA 'H' 4.4 WELD SHOW-THROUGH MINIMIZED X
UNCOPED BEAM END COPED BEAM END
VARIES, SEE VARIES, SEE C.1 ROLLED MEMBERS MINIMIZED DISTORTION
PLAN PLAN

NOTES:
1.1 PRIOR TO BLAST CLEANING, GREASE AND OIL ARE REMOVED BY SOLVENT
CLEANING TO MEET SSPC-SP 1.
1.2 ROUGH SURFACES ARE DEBURRED AND GROUND SMOOTH. SHARP EDGES
EMBED PLATE SCHEDULE RESULTING FROM FLAME CUTTING, GRINDING, AND ESPECIALLY SHEARING ARE
W8x35

END LAP - 5/8"Ø PUDDLE WELD SOFTENED.

MARK EMBED PLATE SIZE (HXL) EMBED PLATE REMARKS 1.3 INTERMITTENT WELDS ARE MADE CONTINUOUS, EITHER WITH ADDITIONAL
1 1/2" ROOF DECK WELDING, CAULKING, OR BODY FILLER. FOR CORROSIVE ENVIRONMENTS, ALL
EP1 16"X8" 1/2" PLATE W/ 3/4" Ø X4" STUDS (TYPE B) JOINTS ARE SEAL WELDED. SEAMS OF HOLLOW STRUCTURAL SECTIONS ARE
x x x x x x x x x x x x x x x x
36" COVERAGE ACCEPTABLE AS PRODUCED.
ROOF LEVEL ROOF LEVEL x x x x
1.4 ALL BOLT HEADS IN CONNECTIONS ARE ON THE SAME SIDE, AS SPECIFIED, AND I hereby certify that this plan, specifcation or report was
EP2 24"X10" 1/2" PLATE W/ 3/4" Ø X4" STUDS (TYPE D) x x x x
CONSISTENT FROM ONE CONNECTION TO ANOTHER. prepared by me or under my direct supervision and that I
114'-6'' 114'-6'' AREA H x x x x SIDE MARGIN (LONGITUDINAL EDGE) 1.5 WELD SPATTER, SLIVERS, AND SURFACE DISCONTINUITIES ARE REMOVED. WELD
x x x x x x x x x x x x x 3/8"X1 1/2" SEAM WELD am a duly Licsened Professional Engineer under the laws
PROJECTION UP TO 1/16" (2mm) IS ACCEPTABLE FOR BUTT AND PLUG WELD
Central: Autodesk Docs://216051 - Winneshiek Expansion and Renovation/216051 - Winneshiek Expansion and Renovation_CENTRAL_2022.rvt

36/5 PATTERN of the state of Minnesota.

x x x x JOINTS.
W10X49

W10X49

W10X68

W10X49

Embed plate x x x x SIDE LAP, TYP - #10 TEK SCREWS 2.1 VISUAL SAMPLES ARE EITHER A 3-D RENDERING, A PHYSICAL SAMPLE, A FIRST-
9

.
x x x x OFF INSPECTION, A SCALED MOCK-UP, OR A FULL-SCALE MOCK-UP, AS SPECIFIED
36/4 PATTERN SPACING OF FASTENERS
x x x x x x x x x x x x x IN THE CONTRACT DOCUMENTS. Katherine Russell
DIAGRAMMATIC ONLY SEE DECK

.
x x x x 2.2 THESE TOLERANCES ARE ONE-HALF OF THOSE FOR STANDARD STRUCTURAL S P27101
FASTENER SCHEDULE FOR Date 12/30/2022 Lic. No.
x x x x TEEL AS SPECIFIED IN AISC CODE OF STANDARD PRACTICE.
DIMENSIONS.
MAIN LEVEL MAIN LEVEL SHEET LENGTH 2.3 MEMBERS MARKINGS DURING THE FABRICATION AND ERECTION PROCESSES ARE
EMBED PLATE DIAGRAMS 3 - SPAN PREFERRED
INTERMEDIATE SUPPORTS - 3.1
NOT VISIBLE.
ALL MILL MARKS ARE NOT VISIBLE IN THE FINISHED PRODUCT. Description
Revisions
Date Num
100'-0'' 100'-0'' 2 - SPAN MINIMUM 5/8"Ø PUDDLE WELD 3.2 CAULKING OR BODY FILLER IS ACCEPTABLE.
Autodesk Docs://Winneshiek Expansion and Renovation/WSER - North Building.rvt

L L 3.3 SEAMS ARE ORIENTED AWAY FROM VIEW OR AS INDICATED IN THE CONTRACT
DOCUMENTS.
3" 3" 3" EQ EQ 3" 2" MIN END LAP 3.4 THE MATCHING OF ABUTTING CROSS SECTIONS IS REQUIRED.
0" AT COMPOSITE DECK 3.5 THIS CHARACTERISTIC IS SIMILAR TO 2.2 ABOVE. A CLEAR DISTANCE BETWEEN
ABUTTING MEMBERS OF 1/8" (3mm) IS REQUIRED.
2" COMPOSITE 3.6 HIDDEN BOLTS MAY BE CONSIDERED.
2"

2"

L DECK
DECK FASTENER SCHEDULE 4.1 HSS SEAMS ARE TREATED SO THEY ARE NOT APPARENT.
36" COVERAGE
LOWER LEVEL LOWER LEVEL 4.2 IN ADDITION TO A CONTOURED AND BLENDED APPEARANCE, WELDED
1 1/2" 1 1/2" DECK TYPE 1 1/2" ROOF DECK TYP B 2" COMPOSITE
TRANSITIONS BETWEEN MEMBERS ALSO ARE CONTOURED AND BLENDED.
36/4 PATTERN
EQUALLY SPACED

EQUALLY SPACED

88'-5 3/8" 88'-5 3/8" L 4.3 THE STEEL SURFACE IMPERFECTIONS ARE FILLED AND SANDED.
INTERMEDIATE SUPPORTS AND END LAPS 36/4 PATTERN TYPE 36/4 PATTERN TYPE
INFILL STUDS

INFILL STUDS

4.4 WELD SHOW-THROUGH ON THE BACK SIDE OF A WELDED ELEMENT CAN BE

1 1/2"

1 3/8" 1 3/8" MINIMIZED BY HAND GRINDING THE BACK SIDE SURFACE. THE DEGREE OF WELD-
28/12/2022 10:52:18

SIDE MARGINS 12"OC MAX 36" O.C. MAX THROUGH IS A FUNCTION OF WELD SIZE AND MATERIAL.
H

PLATE SIZE 12X12X3/4 12x12x3/4 14x14x3/4 9x12x3/4 12x18x1 C. ADDITIONAL CHARACTERISTICS MAY BE ADDED FOR CUSTOM ELEMENTS. Comm: 216050
BASE PLATE

SIDE LAPS #10 TEKS @15 #10 TEKS @ 36"

ANCHOR BOLTS 4-3/4''Ø 4-3/4''Ø 4-3/4''Ø 8-3/4''Ø 8-1''Ø Date: 12/30/2022
EQ

NOTE: OTHER POWER DRIVEN FASTENERS WAY BE USED IF SPACING Drawn:

WELDING a= 1/2" a= 1/2" a= 1/2" a= 3/8" a= 1/2"
H

PROVIDES EQUIVALENT DIAPHRAGM CAPACITY. RECEIVE WRITTEN Check: North

EQ

DETAIL 3/S4.00 3/S4.00 3/S4.00 4/S4.00 APPROVAL FROM ARCHITECT

2"

2"
1 1/2"

NOTES: Steel deck fastener. Detail

1. EXTEND STRAIGHT TYPICAL ANCHOR BOLT 12" INTO CONCRETE, MINIMUM, SEE SCHEDULE AND
DETAIL 1/S4.00.
TYPE - A TYPE - B TYPE - C TYPE - D 6 SCHEDULES,
2. PROVIDE 2" NON-SHRINK GROUT BELOW BASE PLATE.
3. SEE DETAILS 1-5/S4.00 FOR ANCHOR BOLTS.
4. ANCHOR BOLTS ASTM F1554 GR55.
SECTIONS AND
Embed plate Diagram Plate Schedule
S 10 DETAILS

Scale: As indicated

PERMIT SET
NOT FOR CONSTRUCTION S4.00