ANNEXURE -I

BILL OF QUANTITIES
SHOWROOM AT BAMBOLIM

Item Description Unit

No. Qty Rate AMOUNT

A EXCAVATION EARTHWORKS
A01 Excavation insoft soil,murrum ,clay ,sandy soil
etc by using mechanical means for
foundations trenches ,footings , walls foundations ,
plinth beams, roads and drains etc., and dumping
material within site at designated place

a 0 to 1.5m Cum 400 0

b 1.5 to 2.5m Cum 425 0
c 2.5 and above Cum 450 0

A02 Excavation in hard rock/laterite rock by using

mechanial means pneumatic breakers for
foundations trenches ,footings , walls foundations ,
plinth beams, roads and drains etc..and dumping
material within site at designated place

a 0 to 1.5m Cum 726.00 900 653400

b 1.5 to 2.5m Cum 925 0
c 2.5 and above Cum 950 0

A03 Transporing and disposing of excess excavated earth

Cum 300 0
out of site by using loaders and dumpers

A04 Providing & Filling approved quality of earth or

murrum in plinth, open trenches, tank foundations
and under floors,laid in layers including watering,
ramming, levelling and compacting with vibrator
compactor and at unaccesible places wooden or steel
rammer.

a with available earth on site Cum 726.00 350 254100

b With earth brought from outside Cum 809.00 850 687650

A05 Providing and laying Dry laterite rubble

soling of specified thickness under floors,
foundations, trenches, roads, drains, compound
wall, etc with laterite stones of the approved sizes
including handsetting vertically in regular lines,
interstices being filled in small rubble chips laid
to required levels, slopes and watering and
compacting with vibrator Compactors, with all
leads and lifts including landscaping
etc, complete.

a With available rubbles at site Cum 42.00 1800 75600

b With rubbles brought from outside Cum 2800 0

A06 Providing and laying in position Plum Cement

Concrete of M10 grade nominal mix, with
hard laterite stones for retaining wall etc. Plum
should not exceed 50% of the volume of the finished
concrete including machine mixing, Cum 7500 0
consolidating, compacting with vibrators, leveling,
finishing,curing etc. as per technical specifications etc,
complete., Excluding centering and shuttering.

Page 1 of 9
Item Description Unit
No. Qty Rate AMOUNT

Page 2 of 9
Item Description Unit
No. Qty Rate AMOUNT

A07 Providing and injecting chemical emulsions for

pre-construction anti-termite treatment and
creating a chemical barrier as per IS: 6313 (part II)
1981, in plinth filling , junction of walls and floors
along external perimeter of the building etc. all Sqmt 260.00 120 31200
complete as per specifications and as directed
including providing guarantee for a period of 10
years. (Mode of measurement shall be plinth area
Only)

B CONCRETE WORK

B01 Providing & laying in position Plain Cement

Concrete of M10 grade, (1:3:6) nominal mix with
20/40 mm size and downward graded granitic
/ basaltic stone aggregate , under column footings,
walls, plinth beams, under plinth and trenches,
roads, drains, compound wall, etc. including machine Cum 139.00 7500 1042500
mixing consolidating, compacting with heavy
wooden rammers or vibrators, curing, with all
leads and lifts as per technical specifications etc.
complete.but excluding shuttering .

B02 Providing and laying in position Reinforced

Cement Concrete M25 grade, machine mixed
and machine vibrated design mix cement
concrete with 20 mm downward graded granitic/
basaltic stone aggregate for all shapes with
vibration by needle and surface vibrators, curing, .
at all leads and heights as per technical
specifications etc. complete, including admixtures in
recommended proportions as per IS 9103 to
accelerate, retard setting of concrete, improve
workability without impairing the strength and
durability as per the direction of the Engineer-in-
charge, Excluding cost of Shuttering, Centering
for following items; Concrete will be
either site batch mix or ready mix concrete.

a For Footings, Foundations, Rafts, etc. Cum 223.00 9100 2029300

b For Column & Column Pedestals etc.at all heights Cum 40.00 9400 376000
c For Staircase, waist slab, landings, steps etc. Cum 19.00 9400 178600
d plinth beams Cum 27.00 9300 251100
e For Flat Slabs , Beams, Lintels, Chajjas,etc
Cum 194.00 9400 1823600

f For walls /retaining walls ,watertanks ,lift pardi etc . Cum 137.00 9400 1287800
g For Sloping Beams, Slabs, Chajjas, etc Cum 11.00 9500 104500
h For strorm water drains Cum 9400 0
i If concrete grade is M30 Grade concrete Instead of
M25 extra over rate will be for above rates cum 14.00 425 5950

Page 3 of 9
Item Description Unit
No. Qty Rate AMOUNT

B05 Centering and shuttering including strutting, propping

0
etc. and removal of form for :
a Sides for PCC Rm 200 0
b For Footings, Rafts, etc. Sqm 800 0
c For Column & Column Pedestals etc. Sqm 900 0
d For Staircase, waist slab, landings, steps etc. Sqm 925 0
e plinth beams Sqm 900 0
f For Flat Slabs , Beams, Lintels, Chajjas,etc Sqm 950 0
g For walls /retaining walls ,watertanks ,lift pardi etc . Sqm 950 0
h For Sloping Beams, Slabs, Chajjas, etc Sqm 975 0
i For strorm water drains Sqm 850 0
j For height more then 3.5mt shuttering and centering
for the RCC slab, beam,sloping or flat more than 3.5mt
where extra scaffolding erection is required rate will Sqm 350 0
be extra over for above quoted shuttering items

C REINFORCEMENT/STRUCTURAL WORK
C01 Providing ,Cutting, bending to shape, Lifting , fixing
and tieing TMT Reinforcement Steel in position
and providing cover blocks etc. as per specification .
All laps ,chairs and spacer bars will be considered for kgs 70000.00 86 6020000
the measurements separately as per actual
Basic Rate 60 per KG

C02 Proviidng ,Fabricating, straightening, cutting,

cleaning, erecting, placing in position and connecting
M. S. structural work fabricated from hollow sections,
rolled sections, built up sections such as plates,
bracings, stiffeners, etc. in roof trusses, columns,
portal frames, beams, bracings, platforms, pipe
trestles, staircases, monorails, cleats, protection
angles, brackets etc. including transportation, loading
and unloading as and when required, cutting,
wastage, welding, (shop and site) bolting wherever KGS 125
necessary painting with one coat of epoxy based
primer and two coats of approved epoxy paint in
approved colour complete as specified and as
directed, at any height and at all levels. Foundation
Bolts, nuts, washers etc. required are in tenderer’s
scope. (Brand: TATA/ SAIL/JSW/RINL ONLY)
Basic Rate 70 per KG

D MASONRY WORK
D01 Providing and constructing laterite stone masonry
in foundation, underground tanks, pits, retaining
walls, sumps, drains, trenches, compound walls
etc.at all leads, levels and heights in cement mortar Cum 94.00 6200 582800
(1:5) including scaffolding, raking of joints, curing
etc. complete as directed.

D02 Providing and constructing dressed laterite stone

masonry in Superstructure .at all leads, levels and
heights in cement mortar (1:4) including scaffolding, Cum 94.00 6400 601600
raking of joints, curing etc. complete as directed.

D03 Providing and constructing cc block masonry(100mm

Sqm 94.00 1650 155100
thick) in CM 1:4 proportion .

Page 4 of 9
Item Description Unit
No. Qty Rate AMOUNT

D04 Providing and constructing AAC block

Cum 8500
masonry(200MM THICK in CM 1:4 proportion .

Page 5 of 9
Item Description Unit
No. Qty Rate AMOUNT

E PLASTER
E01 Providing & applying 12mm thick single coat
Cement Plaster to Internal walls, beams, ceiling etc.
and all other vertical surfaces at all heights and
leads in CM (1:4) to RCC and masonary work including
Sqm 735.00 490 360150
scaffolding, racking out joints in masonry and
concrete, The surface shall be prepared either rough
or smooth as per the requirement .

E02 Providing and applying External cement plaster

18mm thick in two coats, with base coat of 12 mm
thick in cement mortar (1:4); and finished with
second coat of 6 mm thick in cement mortar (1:3) Sqm 772.00 700 540400
to concrete / masonry external surfaces including
sponge finish, curing, scaffolding, etc.

E03 Providing & doing Drip Moulds of size 50mm wide

and upto 10mm deep in cement plaster (1:3) over
chajjas and parapets, etc at all levels locations
including scaffolding, curing, grooves, strips, Rmt 150 0
rounds,
bends, etc. complete.

F WATERPROOFING WORK
Providing and applying as per manufacturers
specifications a minimum of two coats of
waterproofing coating of Fosrock TGP BRUSH BOND
F01 including thorough surface preparation, for slabs, Sqm 316 700 221200
sunken slabs,bathroom ,toilets side walls, retaining
wall etc.

Providing water proofing treatment over the new RCC

roofs, terrace, sunken slabs, chajjas by spreading
cement slurry over the RCC slab and laying of 100 mm
average laterite stone coba with the necessary
gradient for easy flow of rain water and the coba
should be covered with damp proof, joint less water
F02 Sqm 316 1350 426600
proofing plaster of mix 1:3 (1 cement : 3 Fine sand),
finish smooth with wooden trowel with false marking
of 30cm squares. the Vertical surfaces of the adjoining
walls are to be treated upto a height of 30cms
including rounding of junctions

Providing and laying dry laterite rubble soling of size

not exceeding 100mm as COBA in toilet and bath
sunken portions etc, including handsetting
vertically in regular lines,insterstices being filled in
F03 small rubble chips and cement mortar laid to Cum 22 4000 88000
required levels, slopes and watering consolidating
and finishing to required levels, curing etc
complete. Care to be taken to ensure
Plumbing pipes are not disturbed.

Providing and laying screed concrete of 50mm thick

F04 over sloping roof of M20Grade adding waterproofing sqm 51 600 30600
compound etc .
0
G FLOORING WORK 0

Page 6 of 9
Item Description Unit
No. Qty Rate AMOUNT

Providing, Cutting & Laying of 10 mm thk.

VitrifiedTiles flooring including cement & sand
mortar bedding up to 30 mm avg 20mm thk. floor
finish level as per drawing and detail, with 1:4
G01 proportion (1 cement : 4 sand ), joints finished flush in Sqmt 914 1350 1233900
cement, curing, in proper line and water level or slope
etc complete as per drawings & detail directed by
architect(basic rate condidered Rs 600/- per sqm).

0
Providing, Cutting & fixing of 10 mm thk.
VitrifiedTiles skirting of 100mm high including
cement in proper line & level as per drawing and
G02 detail, joints finished flush in cement, curing, in proper Rmt 150 400 60000
line and water level etc complete as per drawings &
detail directed by architect. (only quote)(basic rate
condidered Rs 600/- per sqm)
0
Providing, Cutting & fixing of 10 mm thk.
VitrifiedTiles on walls including cement & sand
mortar bedding up to 30 mm avg 20mm thk. floor
finish level as per drawing and detail, with 1:4
G03 proportion (1 cement : 4 sand ), joints finished flush in Sqmt 138 1550 213900
cement, curing, in proper line and water level or slope
etc complete as per drawings & detail directed by
architect. (only quote) (basic rate condidered Rs 600/-
per sqm)
0
Providing, Cutting and Fixing wash-basin counter of
approved Granite stone, with necessory M.S. supports
in proper line levels & kaddappa as the base support,
with cutting holes of required sizes in appropriate
places as per the drawing to receive Basin, pipes etc.
counter granite to be fixed in the cement mortar 1:3
proportion (1 cement : 6 sand), as per sizes &
patterns, Counter fascia upto 300mm and counter
G04 depth uptil 675mm including making necessary Sqmt 6 6200 37200
grooves of 29mm wide and 5mm deep and , offsets,
cutouts and joints to be filled with matching approved
joint filler, curing and cleaning with polishing and
rounded mirror polished corners etc complete as per
the drawing given by the architect.(basic rate
condidered Rs 170/- per sqft)

0
Providing, Cutting & fixing of 18 to 20mm thk Kota
stone tile flooring including cement mortar filled
upto 50 mm thk. in proper line level & plum as per
G05 drawing and detail, with 1:4 proportion (1 cement : 4 Sqmt 1500 0
sand) with a levelling screed base & proper fnish joint.
Colour and finish to be approved by Architect. (only
quote)
0
Providing and laying ,compacting Pavers block -60mm
G06 thick over a sand bed etc complete .basic rate -Rs Sqm 1300 0
600per sqm
0
0
H DOORS AND WINDOWS 0

Page 7 of 9
Item Description Unit
No. Qty Rate AMOUNT

Providing and fixing of aluminium window with 3

tracks and 3 shutters sliding window with tubular
frame ployster powder if thicness 75-80 microns with
H01 approved standard accessaries such as ball beaing Sqmt 9000 0
rollers, concealed lock, 6mm thick plain clear glass
with EPDM beading etc. (only quote)

0
H02 Providing and fixing of aluminium window with 2
tracks and 2 shutters sliding window with tubular
frame ployster powder if thicness 75-80 microns with
approved standard accessaries such as ball beaing Sqmt 8500 0
rollers, concealed lock, 6mm thick plain clear glass
with EPDM beading etc. (only quote)

H03 Providing and fixing 30mm thick flush door along with
hinges and with both side veneer internal doors Sqmt 20 7200 144000
including handle towerbolt,door stopper
0
I PAINTING WORKS 0
Providing and applying two coats of Acrylic emulsion
paint for interior walls with approved shade ,over two
caot of cement putty and one coat of acrilic putty and
I01 one coat of primer to all internal surfaces at all Sqm 1231 440 541640
levels and at all heights including scaffolding, etc. all
complete.

0
Providing and applying External paint with two coats
of Weather Proof Acrylic paint of ASIAN - APEX ULTIMA
of approved shade over one coat of primer at all
I02 levels to all external surfaces of walls, chajjas, canopy Sqm 424 390 165360
and other RCC work including scaffolding, etc.
complete as per specifications and as directed by
Engineer.

Page 8 of 9
Item Description Unit
No. Qty Rate AMOUNT

J OTHER ITEMS 0
Providing and fixing 4'' x 2.5''. first classTeak wood
Door / Window frames , fixing the same to
masonary concrete surface with required Holdfast ,
J01 Anchor fastners,concrete etc. complete in proper line, Rmt 2200 0
level and plumb to take marble/ stone/ tile, etc. as per
drawing and directed by the architects.

0
Finishing of Electrical conduiting with fixing of chicken
J02 Rm 190 0
mesh and kataka up to150 mm wide
0
Providing & fixing of Gypsum Board false ceiling
with G.I frame & gypsum sheet of India gypsum make
in 26 gauge as per design and details with galvanize
iron frame work with 2”x1/2” G.I subsidizing members
(channel framing 1’-3” center to center to receive
Gypsum sheet) G.I screw will be used for fixing the
frame with gypsum sheet (sheet 6’-0” x 4’-0”x
1/2”thk) and joints finished with stretchable mesh
tape with joint compound and two coats of dry wall top
J03 coat suitable for Gypboard (as recommended sqft 140 0
practices of BPB India gypsum)and 2mm thk board
finish plaster is applied on the entire surface of
Gypboard to acheive smooth and seamless finish at
the joints, Including providing GI runner supports and
making cutouts for light fittings, diffuser, grill,
speakers, sprinklers, drops, grooves, chamfering,
rounding, moulding etc as per directions.

0
J06 Core cutting in RCC slab /beams 0
a 50mm dia Nos 450 0
b 75mm dia Nos 600 0
c 100mm dia Nos 850 0
d 150mm dia Nos 1000 0
e 175mm dia Nos 1500 0
0
J08 Providing and fixing of pvc sleeves 0
a 50mm dia Nos 90 0
b 75mm dia Nos 120 0
c 100mm dia Nos 140 0
d 150mm dia Nos 180 0
e 175mm dia Nos 220 0
0
J09 CONCEALED PIIPING FOR ELECTRICAL WORKS(PIPE
0
MAKE-Polycab/Precission )
1 20mm dia MMS pipe Rm 100 0
2 25mm dia MMS pipe Rm 120 0
3 20mm Junction box Nos 90 0
4 25mm Junction box Nos 100 0
5 Fan hook box Nos 190 0

TOTAL 20223750

Note :Shuttering quantity is not given by consultant so cost of shuttering is not added in the amo

Page 9 of 9