configuration guide

hp StorageWorks
enterprise virtual array
hardware
Product Version: 3.0

Second Edition (May 2003)

Part Number: AA-RS28B-TE

This guide describes the various hardware configurations used for the HP StorageWorks Enterprise Virtual
Array. It discusses the quantity of various hardware components in each configuration and how the hardware
components are connected to each other. The expansion of existing racks is also discussed.

For the latest version of this document and other storage system documentation, visit the HP storage website at:
http://welcome.hp.com/country/us/eng/prodserv/storage.html.
© Copyright 2001 - 2003 Hewlett-Packard Development Company, L.P.
Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for
incidental or consequential damages in connection with the furnishing, performance, or use of this material.
This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied,
reproduced, or translated into another language without the prior written consent of Hewlett-Packard. The information contained in
this document is subject to change without notice.
Compaq Computer Corporation is a wholly-owned subsidiary of Hewlett-Packard Company.
All other product names mentioned herein may be trademarks of their respective companies.
Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein. The information is
provided “as is” without warranty of any kind and is subject to change without notice. The warranties for Hewlett-Packard Company
products are set forth in the express limited warranty statements accompanying such products. Nothing herein should be construed as
constituting an additional warranty.
Printed in the U.S.A.

Enterprise Virtual Array Hardware Configuration Guide

Second Edition (May 2003)
Part Number: AA-RS28B-TE
 contents

Contents
About this Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Text Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Equipment Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Rack Stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
HP Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
HP Storage Website . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
HP Authorized Reseller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

1 Enterprise Virtual Array Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Storage Racks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
41U Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
42U Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
2C6D Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2C12D Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
8C8D Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
2C2D Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
0C6D Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
0C12D Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Fibre Channel Drive Enclosures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
HSV110 Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Fibre Channel Loop Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Fibre Channel Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

2 Enterprise Virtual Array Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

2C12D Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Enclosure Address Bus Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Fibre Channel Loop Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Cable Management Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Cable Management Arms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Cable Containment Spools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
2C6D Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Enterprise Virtual Array Hardware Configuration Guide 3

Contents

Enclosure Address Bus Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Fibre Channel Loop Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Cable Management Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
8C8D Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Enclosure Address Bus Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Fibre Channel Loop Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Cable Management Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
2C2D Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Enclosure Address Bus Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Fibre Channel Loop Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Cable Management Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
2C12D + 0C6D Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Enclosure Address Bus Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Fibre Channel Loop Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
2 x 2C12D + 0C12D Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Enclosure Address Bus Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Fibre Channel Loop Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

3 Upgrading Existing Racks to Enterprise v2.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Expansion Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
FC Loop Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Fibre Channel Cable Reconfiguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

4 Expanding a Rack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Adding FC Drive Enclosures to a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
2C6D Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
2C6D + 6D Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Enclosure Address Bus Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Fibre Channel Loop Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
0C6D + 6D Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Enclosure Address Bus Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Fibre Channel Loop Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99

A Regulatory Notices and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
Federal Communications Commission Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
FCC Class A Certification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
Class A Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
Class B Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Declaration of Conformity for Products Marked with the FCC Logo, United States Only . . . . . . . .111
Modifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Laser Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Laser Safety Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Compliance with CDRH Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Certification and Classification Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Canadian Notice (Avis Canadien) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Class A Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Class B Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
European Union Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113

4 Enterprise Virtual Array Hardware Configuration Guide

 Contents

Notice for France . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113

Germany Noise Declaration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
Japanese Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
Harmonics Conformance (Japan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
Taiwanese Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
Country-Specific Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Fibre Channel Drive Enclosure Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
Physical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118
Fibre Channel Switch Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Controller Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Physical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Enterprise Rack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
Physical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125

Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Figures
1 41U rack—front and rear views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2 42U rack—front and rear views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3 2C6D configuration—rear view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4 2C12D configuration—rear view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5 8C8D configuration—rear view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6 2C2D configuration—front and rear views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7 0C6D configuration—rear view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8 0C12D configuration—rear view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
9 FC drive enclosure—front and rear views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
10 HSV110 controller—front and rear views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
11 FC loop switch—front and rear views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
12 2C12D configuration—enclosure address bus cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
13 2C12D configuration—Fibre Channel loop 1A with FC loop switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
14 2C12D configuration—Fibre Channel loop 1B with FC loop switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
15 2C12D configuration—Fibre Channel loop 2A with FC loop switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
16 2C12D configuration—Fibre Channel loop 2B with FC loop switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
17 2C12D configuration—Fibre Channel loop 1A with expansion panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
18 2C12D configuration—Fibre Channel loop 1B with expansion panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
19 2C12D configuration—Fibre Channel loop 2A with expansion panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
20 2C12D configuration—Fibre Channel loop 2B with expansion panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
21 2C12D cable management configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
22 2C6D configuration—enclosure address bus cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
23 2C6D configuration—Fibre Channel loop 1A with FC loop switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
24 2C6D configuration—Fibre Channel loop 1B with FC loop switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
25 2C6D configuration—Fibre Channel loop 2A with FC loop switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
26 2C6D configuration—Fibre Channel loop 2B with FC loop switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
27 2C6D configuration—Fibre Channel loop 1A with expansion panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Enterprise Virtual Array Hardware Configuration Guide 5

Contents

28 2C6D configuration—Fibre Channel loop 1B with expansion panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

29 2C6D configuration—Fibre Channel loop 2A with expansion panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
30 2C6D configuration—Fibre Channel loop 2B with expansion panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
31 2C6D cable management configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
32 8C8D configuration—enclosure address bus cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
33 8C8D configuration—Fibre Channel loop 1A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
34 8C8D configuration—Fibre Channel loop 1B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
35 8C8D configuration—Fibre Channel loop 2A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
36 8C8D configuration—Fibre Channel loop 2B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
37 8C8D cable management configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
38 2C2D configuration—enclosure address bus cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
39 2C2D configuration—Fibre Channel loop 1A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
40 2C2D configuration—Fibre Channel loop 1B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
41 2C2D configuration—Fibre Channel loop 2A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
42 2C2D configuration—Fibre Channel loop 2B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
43 2C2D cable management configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
44 2C12D + 0C6D configuration—enclosure address bus cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
45 2C12D + 0C6D configuration—Fibre Channel loop 1A with FC loop switch . . . . . . . . . . . . . . . . . . . . . 65
46 2C12D + 0C6D configuration—Fibre Channel loop 1B with FC loop switch . . . . . . . . . . . . . . . . . . . . . 66
47 2C12D + 0C6D configuration—Fibre Channel loop 2A with FC loop switch . . . . . . . . . . . . . . . . . . . . . 67
48 2C12D + 0C6D configuration—Fibre Channel loop 2B with FC loop switch . . . . . . . . . . . . . . . . . . . . . 68
49 2C12D + 0C6D configuration—Fibre Channel loop 1A with expansion panels . . . . . . . . . . . . . . . . . . . 69
50 2C12D + 0C6D configuration—Fibre Channel Loop 1B with expansion panels . . . . . . . . . . . . . . . . . . . 70
51 2C12D + 0C6D configuration—Fibre Channel loop 2A with expansion panels . . . . . . . . . . . . . . . . . . . 71
52 2C12D + 0C6D configuration—Fibre Channel loop 2B with expansion panels. . . . . . . . . . . . . . . . . . . . 72
53 2 x 2C12D + 0C12D configuration—enclosure address bus cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
54 2 x 2C12D + 0C12D configuration—Fibre Channel loop 1A with FC loop switch . . . . . . . . . . . . . . . . . 75
55 2 x 2C12D + 0C12D configuration—Fibre Channel loop 1B with FC loop switch . . . . . . . . . . . . . . . . . 76
56 2 x 2C12D + 0C12D configuration—Fibre Channel loop 2A with FC loop switch . . . . . . . . . . . . . . . . . 77
57 2 x 2C12D + 0C12D configuration—Fibre Channel loop 2B with FC loop switch . . . . . . . . . . . . . . . . . 78
58 2 x 2C12D + 0C12D configuration—Fibre Channel loop 1A with expansion panels . . . . . . . . . . . . . . . 79
59 2 x 2C12D + 0C12D configuration—Fibre Channel loop 1B with expansion panels. . . . . . . . . . . . . . . . 80
60 2 x 2C12D + 0C12D configuration—Fibre Channel loop 2A with expansion panels . . . . . . . . . . . . . . . 81
61 2 x 2C12D + 0C12D configuration—Fibre Channel loop 2B with expansion panels. . . . . . . . . . . . . . . . 82
62 Expansion panels versus FC loop switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
63 Fibre Channel cabling comparison— Enterprise v1.0 to Enterprise v2.0 . . . . . . . . . . . . . . . . . . . . . . . . . 86
64 2C6D configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
65 2C6D + 6D configuration—enclosure address cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
66 2C6D + 6D configuration—Fibre Channel loop 1A with FC loop switch . . . . . . . . . . . . . . . . . . . . . . . . 91
67 2C6D + 6D configuration—Fibre Channel loop 1B with FC loop switch . . . . . . . . . . . . . . . . . . . . . . . . 92
68 2C6D + 6D configuration—Fibre Channel loop 2A with FC loop switch . . . . . . . . . . . . . . . . . . . . . . . . 93
69 2C6D + 6D configuration—Fibre Channel loop 2B with FC loop switch . . . . . . . . . . . . . . . . . . . . . . . . 94
70 2C6D + 6D configuration—Fibre Channel loop 1A with expansion panel. . . . . . . . . . . . . . . . . . . . . . . . 95
71 2C6D + 6D configuration—Fibre Channel loop 1B with expansion panel . . . . . . . . . . . . . . . . . . . . . . . . 96
72 2C6D + 6D configuration—Fibre Channel loop 2A with expansion panel. . . . . . . . . . . . . . . . . . . . . . . . 97
73 2C6D + 6D configuration—Fibre Channel loop 2B with expansion panel . . . . . . . . . . . . . . . . . . . . . . . . 98
74 0C6D + 6D configuration—enclosure address bus cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
75 0C6D + 6D configuration—Fibre Channel loop 1A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
76 0C6D + 6D configuration—Fibre Channel loop 1B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
77 0C6D + 6D configuration—Fibre Channel loop 2A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

6 Enterprise Virtual Array Hardware Configuration Guide

 Contents

78 0C6D + 6D configuration—Fibre Channel loop 2B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

79 0C6D + 6D configuration—Fibre Channel loop 1A with expansion panels . . . . . . . . . . . . . . . . . . . . . . 104
80 0C6D + 6D configuration—Fibre Channel loop 1B with expansion panels . . . . . . . . . . . . . . . . . . . . . . 105
81 0C6D + 6D configuration—Fibre Channel loop 2A with expansion panels . . . . . . . . . . . . . . . . . . . . . . 106
82 0C6D + 6D configuration—Fibre Channel loop 2B with expansion panels . . . . . . . . . . . . . . . . . . . . . . 107
83 Typical enclosure certification label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Tables
1 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2 LC-SC cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3 LC-LC Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4 Fibre Channel Loop Locations in Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5 Fibre Channel Loop Locations in Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
6 Drive Enclosure Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
7 Drive Enclosure Elements Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
8 Environmental Operating Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
9 Environmental Shipping or Short-Term Storage Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
10 Enterprise Storage System AC Input Line Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
11 AC Input Current and Wattage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
12 Output Voltage and Current Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
13 Dual Power Supply Configuration Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
14 Fibre Channel Switch Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
15 Controller Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
16 Controller Power Supply AC Power Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
17 AC Input Current and Wattage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
18 Controller Power Supply Output Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
19 Enterprise 42U Storage System Rack Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
20 Enterprise 42U Storage System Rack Shipping Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
21 Enterprise 41U Storage System Rack Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
22 Enterprise 41U Storage System Rack Shipping Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
23 Environmental Operating Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
24 Environmental Shipping or Short Term Storage Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
25 Enterprise Storage System AC Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Enterprise Virtual Array Hardware Configuration Guide 7

Contents

8 Enterprise Virtual Array Hardware Configuration Guide

 about this guide

About this Guide

This hardware configuration guide provides information to help you:
■ Learn about the EnterpriseAbout
Virtual Array hardware components.
this Guide
■ Understand the supported storage rack configurations.
■ Convert an Enterprise Virtual Array v1.0 storage rack configuration into an Enterprise
Virtual Array v2.0 storage rack configuration.
■ Expand an Enterprise Virtual Array with drive enclosures.
■ Understand the supported Fibre Channel cable configurations.
About this Guide topics include:
■ Overview, page 10
■ Conventions, page 11
■ Rack Stability, page 13
■ Getting Help, page 14

Enterprise Virtual Array Hardware Configuration Guide 9

About this Guide

Overview
This section covers the following topics:
■ Intended Audience
■ Related Documentation

Intended Audience
This book is intended for use by Enterprise Virtual Array administrators who are experienced
with the following:
■ Working with Fibre Channel cables.
■ Working with Fibre Channel loop switches.
■ Maintaining and operating Storage Area Networks (SANs).

Related Documentation
Additional documentation is available from the HP website at:
http://welcome.hp.com/country/us/eng/prodserv/storage.html.

10 Enterprise Virtual Array Hardware Configuration Guide

 About this Guide

Conventions
Conventions consist of the following:
■ Document Conventions
■ Text Symbols
■ Equipment Symbols

Document Conventions
The document conventions included in Table 1 apply in most cases.
Table 1: Document Conventions
Element Convention
Cross-reference links Blue text: Figure 1
Key and field names, menu items, buttons, and Bold
dialog box titles
File names, application names, and text Italics
emphasis
User input, command and directory names, Monospace font
and system responses (output and messages) COMMAND NAMES are uppercase monospace
font unless they are case sensitive
Variables <monospace, italic font>
Website addresses Blue, underlined sans serif font text:
http://www.hp.com

Text Symbols
The following symbols may be found in the text of this guide. They have the following
meanings.

WARNING: Text set off in this manner indicates that failure to follow directions in the
warning could result in bodily harm or loss of life.

Caution: Text set off in this manner indicates that failure to follow directions could result in
damage to equipment or data.

Note: Text set off in this manner presents commentary, sidelights, or interesting points of
information.

Enterprise Virtual Array Hardware Configuration Guide 11

About this Guide

Equipment Symbols
The following equipment symbols may be found on hardware to which this guide pertains.
They have the following meanings.

These symbols, which mark an enclosed surface or area of the equipment, indicate
the presence of electrical shock hazards. The enclosed area contains no operator
serviceable parts.

WARNING: To reduce the risk of injury from electrical shock hazards, do not open
this enclosure.

These symbols, which mark an RJ-45 receptacle, indicate a network interface

connection.

WARNING: To reduce the risk of electrical shock, fire, or damage to the equipment,
do not plug telephone or telecommunications connectors into this receptacle.

These symbols, which mark a surface or area of the equipment, indicate the presence
of a hot surface or hot component. Contact with this surface could result in injury.

WARNING: To reduce the risk of injury from a hot component, allow the surface to
cool before touching.

These symbols, which mark power supplies or systems, indicate the presence of
multiple sources of power.

WARNING: To reduce the risk of injury from electrical shock, remove all power
cords to completely disconnect power from the power supplies and systems.

These symbols, which mark a product or assembly, indicate that the component
exceeds the recommended weight for one individual to handle safely.

WARNING: To reduce the risk of personal injury or damage to the equipment,

observe local occupational health and safety requirements and guidelines for
manually handling material.

12 Enterprise Virtual Array Hardware Configuration Guide

 About this Guide

Rack Stability
Rack stability protects personnel and equipment.

WARNING: To reduce the risk of personal injury or damage to the equipment, be sure
that:
■ The leveling jacks are extended to the floor.
■ The full weight of the rack rests on the leveling jacks.
■ In single rack installations, the stabilizing feet are attached to the rack.
■ In multiple rack installations, the racks are coupled.
■ Only one rack component is extended at any time. A rack may become unstable if
more than one rack component is extended for any reason.

Enterprise Virtual Array Hardware Configuration Guide 13

About this Guide

Getting Help
If you still have a question after reading this guide, contact an HP Authorized Service
Representative or access our website: http://www.hp.com.

HP Technical Support
In North America, call technical support at 1-800-354-9000, available 24 hours a day, 7 days a
week.

Note: For continuous quality improvement, calls may be recorded or monitored.

Outside North America, call technical support at the nearest location. Telephone numbers for
worldwide technical support are listed on the HP website under support:
http://thenew.hp.com/country/us/eng/support.html.
Be sure to have the following information available before calling:
■ Technical support registration number (if applicable)
■ Product serial numbers
■ Product model names and numbers
■ Applicable error messages
■ Operating system type and revision level
■ Detailed, specific questions

HP Storage Website
The HP website has the latest information on this product, as well as the latest drivers. Access
storage at: http://welcome.hp.com/country/us/eng/prodserv/storage.html. From this website,
select the appropriate product or solution.

HP Authorized Reseller
For the name of your nearest HP authorized reseller:
■ In the United States, call 1-800-345-1518
■ In Canada, call 1-800-263-5868
■ Elsewhere, see the HP website for locations and telephone numbers: http://www.hp.com.

14 Enterprise Virtual Array Hardware Configuration Guide

Enterprise Virtual Array
Hardware
1
This chapter briefly discusses the hardware components in the Enterprise Virtual Array. The
following topics are discussed:
■ Storage Racks, page 16
■ Fibre Channel Drive Enclosures, page 24
■ HSV110 Controllers, page 25
■ Fibre Channel Loop Switches, page 26
■ Fibre Channel Cables, page 27

Enterprise Virtual Array Hardware Configuration Guide 15

Enterprise Virtual Array Hardware

Storage Racks
The Enterprise Virtual Array can be housed in two different storage racks: the 42U rack or the
41U rack. Both storage racks can hold a maximum of 12 Fibre Channel drive enclosures (FC
drive enclosures) and two controllers.

41U Rack
The 41U rack is graphite in color and 993 mm (39.1 inches) deep. The storage rack features
standard 19-inch mounting rails. The 41U rack can support Enterprise Virtual Array
configurations that include Fibre Channel loop switches (FC loop switches).
Figure 1 shows the front and rear views of a 41U rack.
1 FC drive enclosure
Front Rear 2 FC loop switches
3 Controller pair
1 1

2 2

41U 3 3

2 2

CXO7872B

Figure 1: 41U rack—front and rear views

42U Rack
The 42U rack is opal in color and 909 mm (35.8 inches) deep. The storage rack features
standard 19-inch mounting rails. The 42U rack can support Enterprise Virtual Array
configurations that include FC loop switches or expansion panels.
Figure 2 shows the front and rear views of a 42U rack.

16 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Hardware

1 FC drive enclosure
Front Rear 2 FC loop switches
3 Controller pair
1 1

2 2
42U 3 3

2 2

CXO7873B

Figure 2: 42U rack—front and rear views

2C6D Features
The following features are included in the 2C6D configuration:
■ One storage rack
■ Two controllers
■ Six 14-drive bay FC drive enclosures
■ Four FC loop switches
■ Sixteen internal Fibre Channel cables
■ Seven 2-port enclosure address bus junction boxes
■ Eight AC strips
■ Two 0U PDUs

Note: Disks must be ordered separately.

The 2C6D configuration can contain a maximum of 3.1 TB (84 36.4-GB disks), 6.1 TB (84
72.8-GB disks), or 12.3 TB (84 146-GB disks) of storage capacity.

Enterprise Virtual Array Hardware Configuration Guide 17

Enterprise Virtual Array Hardware

Note: The 2C6D configuration can be expanded to increase storage capacity. However, there is a
limit to expansion; each controller pair can support a maximum of 240 disks.

Figure 3 shows the rear view of the 2C6D configuration.

1 3U blank
2 FC drive enclosure
3 FC loop switch
1
4 Controller pair

3
4
3

CXO7874B

Figure 3: 2C6D configuration—rear view

2C12D Features
The following features are included in the 2C12D:
■ One storage rack
■ Two controllers
■ Twelve 14-drive bay FC drive enclosures
■ Four FC loop switches
■ Thirty-two internal Fibre Channel cables
■ Seven 2-port enclosure address bus junction boxes
■ Eight AC strips
■ Two 0U PDUs

Note: Disks must be ordered separately.

18 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Hardware

The 2C12D configuration can contain a maximum of 6.1 TB (168 36.4-GB disks), 12.2 TB
(168 72.8-GB disks), or 24.5 TB (168 146-GB disks) of storage capacity.

Note: The 2C12D configuration can be expanded to increase storage capacity. However, there is
a limit to expansion; each controller pair can support a maximum of 240 disks.

Figure 4 shows the 2C12D configuration.

1 FC drive enclosure
2 FC loop switch
1
3 Controller pair

2
3
2

CXO7875B

Figure 4: 2C12D configuration—rear view

8C8D Features
The following features are included with the 8C8D configuration:
■ One storage rack
■ Eight controllers
■ Eight 14-drive bay FC drive enclosures
■ Thirty-two internal Fibre Channel cables
■ Seven 2-port enclosure address bus junction boxes
■ Eight AC strips
■ Two 0U PDUs

Enterprise Virtual Array Hardware Configuration Guide 19

Enterprise Virtual Array Hardware

Note: Disks must be ordered separately.

The 8C8D configuration can contain a maximum of 4.1 TB (112 36.4-GB disks), 8.2 TB (112
72.8-GB disks), or 16.4 TB (112 146-GB disks) of storage capacity.
Figure 5 shows the 8C8D configuration.
1 Controller pair
2 FC drive enclosure

CXO7876B

Figure 5: 8C8D configuration—rear view

2C2D Features
The following features are included in the 2C2D configuration:
■ One 41U storage rack
■ Two controllers
■ Two 14-drive bay FC drive enclosures
■ Eight internal Fibre Channel cables
■ Seven 2-port enclosure address bus junction boxes
■ Eight AC strips
■ Two 0U PDUs

Note: Disks must be ordered separately.

20 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Hardware

The 2C2D configuration can contain a maximum of 1.0 TB (28 36.4-GB disks), 2.0 TB (28
72.8-GB disks), or 4.1 TB (28 146-GB disks) of storage capacity.
You can expand the storage capacity of the 2C2D configuration by adding drive enclosures
and FC loop switches to the rack.
Figure 6 shows the front and rear views of the 2C2D configuration.
1 FC drive enclosure
Front Rear 2 Controller pair
3 Blank

1 1
3
41U 2 2
3

3 3

CXO8039B

Figure 6: 2C2D configuration—front and rear views

0C6D Features
The following features are included with the 0C6D configuration:
■ One storage rack
■ Six 14-drive bay FC drive enclosures
■ Twelve 5-meter rack-to-rack Fibre Channel cables
■ Six 2-port enclosure address bus junction boxes
■ Eight AC strips
■ Two 0U PDUs

Note: Disks must be ordered separately.

Enterprise Virtual Array Hardware Configuration Guide 21

Enterprise Virtual Array Hardware

The 0C6D configuration can add a maximum of 2.6 TB (72 36.4-GB disks), 5.2 TB (72
72.8-GB disks), or 10.5 TB (72 146-GB disks) of storage capacity to an existing Enterprise
Virtual Array. If the 0C6D is added to a 2C12D, the Enterprise storage system storage
capacity would increase to 8.7 TB (240 36.4-GB disks), 17.5 TB (240 72.8-GB disks), or
35 TB (240 146-GB disks).
Figure 7 shows the rear view of the 0C6D configuration.
1 3U blank
2 FC drive enclosure

CXO7877A

Figure 7: 0C6D configuration—rear view

0C12D Features
The following features are included with the 0C12D configuration:
■ One storage rack
■ Twelve 14-drive bay FC drive enclosures
■ Twenty-four 5-meter rack-to-rack Fibre Channel cables
■ Six 2-port enclosure address bus junction boxes
■ Eight AC strips
■ Two 0U PDUs

Note: Disks must be ordered separately.

22 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Hardware

The 0C12D configuration can add a maximum of 5.2 TB (144 36.4-GB disks), 10.5 TB (144
72.8-GB disks), or 21 TB (144 146-GB disks) of storage capacity. Typically, this storage
capacity is evenly divided between two 2C12D Enterprise storage systems. If you add the
0C12D to two 2C12Ds, the storage capacity for each 2C12D would increase to a maximum of
8.7 TB (240 36.4-GB disks), 17.5 TB (240 72.8-GB disks), or 35 TB (240 146-GB disks).
Figure 8 shows the rear view of the 0C12D configuration.
1 FC drive enclosure
2 3U blank
1

CXO7881A

Figure 8: 0C12D configuration—rear view

Enterprise Virtual Array Hardware Configuration Guide 23

Enterprise Virtual Array Hardware

Fibre Channel Drive Enclosures

Each FC drive enclosure includes the following features:
■ 3U drive enclosure
■ Dual redundant, active-to-active, 2-Gbps Fibre Channel loops
■ Fourteen 1-inch Fibre Channel disks per enclosure
■ Environmental Monitor Unit
■ Dual 2-Gbps Fibre Channel I/O module—A and B
— Enhanced fault detection
— Single GBIC
■ Dual 500-W redundant hot-plug power supplies and fans
For ease of reference, the disk drives are usually referred to by their physical location, the
drive bay number.
Figure 9 shows the front and rear views of the FC drive enclosure and the physical location of
each drive bay.

1 Drive bay 1
1 2 2 Drive bay 14
Front
3 EMU
4 I/O module B
5 Blower 1
6 Power supply 1
7 Blower 2
8 Power supply 2
9 I/O module A
- CAB Only (enclosure
address bus port)
Rear

10

3 4 6 5 8 7 9
CXO7882B

Figure 9: FC drive enclosure—front and rear views

24 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Hardware

HSV110 Controllers
One high performance controller is contained in a controller enclosure. The controller is the
interface between HP StorageWorks Command View EVA and a storage system. A storage
system is composed of one controller pair and multiple drive enclosures.
The Enterprise Virtual Array can contain two HSV110 controllers.
Each HSV110 controller features:
■ High performance power PC microprocessor
■ An Operator Control Panel (OCP) for easy operation
■ Two 2-Gbps Fibre Channel-Switch Fabric host ports
■ Four 2 Gbps FC-AL device ports
— Arranged in redundant pairs
— Data load/performance is balanced across a pair
— Support up to 240 disks per controller pair
■ 1-GB cache per controller, mirrored, with battery backup
■ 2-Gbps FC cache mirroring port with device ports backups
■ Dual power supplies
The HSV110 controller has been modified to contain dual power supplies. The dual power
supplies allow the controller to efficiently use power from two power sources. In the event of a
single power supply failure, the remaining power supply provides the required power to the
controller.
Figure 10 shows the front and rear views of the HSV110 controller.
1 Bezel
2 2 OCP
Front
3 HF1 port
4 HF2 port
1 5 Mirror port
6 1B port
7 2B port
Rear 8 1A port
9 2A port
10 - Power input
; CAB (enclosure
address bus
11 3 4 5 6 7 8 9 port)

CXO8040B

Figure 10: HSV110 controller—front and rear views

Enterprise Virtual Array Hardware Configuration Guide 25

Enterprise Virtual Array Hardware

Fibre Channel Loop Switches

The Enterprise Virtual Array v3.0 uses four FC loop switches to connect all of the drive
enclosures to the controller pair via Fibre Channel cables. Each FC loop switch acts as a
central point of interconnection and establishes a fault-tolerant physical loop topology.
The major features of the FC loop switch are:
■ 2.125-Gbps operating speed
■ Twelve ports
■ Half-width, 1U size
■ System and port status LED indicators
■ Universal power supply that operates between 100 to 250 VAC (or 50 to 60 Hz)
■ Small Form-factor Profile (SFP) transceivers
Figure 11 shows the front and rear views of the Fibre Channel loop switch.
1 SFP Status LED
Bezel
2 Port Bypassed LED
3 POST Fault LED
4 Over Temp LED
5 Power LED
Front 6 Loop Operational
LED

Rear

1 2 3 4 6 5
CXO7884A

Figure 11: FC loop switch—front and rear views

26 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Hardware

Fibre Channel Cables

When an Enterprise Virtual Array is installed in the SAN, an SC–to–LC (1-Gb to 2-Gb) cable
is required for host connectivity. Furthermore, the Enterprise Virtual Array uses 2-meter
LC–to–LC FC cables between the FC loop switches and the FC drive enclosures.
Table 2 and Table 3 provide a listing of available FC cables.
Table 2: LC-SC cables
Length Description
2.0 m (±40 mm) CA ASSY, LC-SC, Optical 2M
5.0 m (±80 mm) CA ASSY, LC-SC, Optical 5M
15.0 m (±150 mm) CA ASSY, LC-SC, Optical 15M
30.0 m (±300 mm) CA-ASSY, LC-SC, Optical 30M
50.0 m (±500 mm) CA-ASSY, LC-SC, Optical 50M

Table 3: LC-LC Cables

Length Description
2.0 m (±40 mm) 2-meter LC-LC Multi-Mode Fibre Cable
5.0 m (±80 mm) 5-meter LC-LC Multi-Mode Fibre Cable
15.0 m (±150 mm) 15-meter LC-LC Multi-Mode Fibre Cable
30.0 m (±300 mm) 30-meter LC-LC Multi-Mode Fibre Cable
50.0 m (±500 mm) 50-meter LC-LC Multi-Mode Fibre Cable

Enterprise Virtual Array Hardware Configuration Guide 27

Enterprise Virtual Array Hardware

28 Enterprise Virtual Array Hardware Configuration Guide

Enterprise Virtual Array
Configurations
2
This chapter briefly discusses various Enterprise Virtual Array configurations. Each section
describes the placement of controllers, drive enclosures, FC loop switches, enclosure address
bus junction boxes and cables, and Fibre Channel cables.
This chapter contains the following sections:
■ 2C12D Configuration, page 30
■ 2C6D Configuration, page 41
■ 8C8D Configuration, page 51
■ 2C2D Configuration, page 57
■ 2C12D + 0C6D Configuration, page 63
■ 2 x 2C12D + 0C12D Configuration, page 73

Enterprise Virtual Array Hardware Configuration Guide 29

Enterprise Virtual Array Configurations

2C12D Configuration
The 2C12D configuration is a single-rack configuration that provides a maximum of 6.1 TB
(168 36.4-GB disks), 12.2 TB (168 72.8-GB disks), or 24.5 TB (168 146-GB disks) of storage
capacity. This configuration can contain a maximum of 168 disks.
The 2C12D configuration is available in either the 41U rack or the 42U rack. The 2C12D can
contain four FC loop switches or one expansion panel.

Enclosure Address Bus Configuration

The 2C12D configuration contains seven enclosure address bus junction boxes at 6U
increments in the left rear rail of the rack. The FC drive enclosures and controller pair in the
2C12D configuration use all seven enclosure address bus junction boxes. Each FC drive
enclosure should be connected to an enclosure address bus junction box. The FC drive
enclosures connect to each enclosure address bus junction box in pairs. The controller pair
connects to the enclosure address bus junction box with a Y cable. Figure 12 shows the
enclosure address bus cable configuration for the 2C12D configuration.
1 Bottom terminator
7 2 Enclosure address 1
6 3 Enclosure address bus cable
4 Enclosure address 7
5 Enclosure address bus junction
box
6 Enclosure address 13
7 Top terminator

5
4

2
1

CXO7885C

Figure 12: 2C12D configuration—enclosure address bus cables

30 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Fibre Channel Loop Configurations

The 2C12D configuration contains four Fibre Channel loops. A Fibre Channel loop is formed
when the FC drive enclosures and the controller pair are connected by Fibre Channel cables.
The 2C12D configuration can use an FC loop switch or an expansion panel to achieve the
desired Fibre Channel loop configuration.
When a configuration uses FC loop switches, each FC drive enclosure in a loop is directly
connected to the associated FC loop switch. The controller pair is also connected directly to
the associated FC loop switch. When the FC loop switch is powered on, it completes a Fibre
Channel loop.
When a configuration uses an expansion panel, a Fibre Channel loop is achieved by
connecting two FC drive enclosures directly to the controllers and linking each FC drive
enclosure together in a chain.
Table 4 provides the locations for the Fibre Channel loops in a storage rack.
Table 4: Fibre Channel Loop Locations in Rack
Fibre
Channel Location in Rack
Loop (viewed from rear)
1A lower right side
1B lower left side
2A upper right side
2B upper left side

Figure 13, Figure 14, Figure 15, and Figure 16 show the 2C12D Fibre Channel loop
configurations with the FC loop switches. Figure 17, Figure 18, Figure 19, and Figure 20
show the 2C12D Fibre Channel loop configurations with expansion panels.

Enterprise Virtual Array Hardware Configuration Guide 31

Enterprise Virtual Array Configurations

Figure 13 shows Fibre Channel loop 1A and the associated FC loop switch.
1 Controller-to-controller Mirror port FC
cable
2 Controller pair
3 FC loop switch
4 FC drive enclosure
5 Fibre Channel cable

1
2

CXO7886B

Figure 13: 2C12D configuration—Fibre Channel loop 1A with FC loop switch

32 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 14 shows Fibre Channel loop 1B and the associated FC loop switch.
1 Controller pair
2 Controller-to-controller
Mirror port FC cable
3 FC loop switch
4 FC drive enclosure
5 Fibre Channel cable

2
1
3
4

CXO7887B

Figure 14: 2C12D configuration—Fibre Channel loop 1B with FC loop switch

Enterprise Virtual Array Hardware Configuration Guide 33

Enterprise Virtual Array Configurations

Figure 15 shows Fibre Channel loop 2A and the associated FC loop switch.
1 FC drive enclosure
2 Fibre Channel cable
3 FC loop switch
4 Controller pair
1
5 Controller-to-controller
Mirror port FC cable

3
5
4

CXO7888B

Figure 15: 2C12D configuration—Fibre Channel loop 2A with FC loop switch

34 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 16 shows Fibre Channel loop 2B and the associated FC loop switch.
1 Fibre Channel cable
2 FC loop switch
3 Controller-to-controller
Mirror port FC cable
4 FC drive enclosure
5 Controller pair

1 4

2
5
3

CXO7889B

Figure 16: 2C12D configuration—Fibre Channel loop 2B with FC loop switch

Enterprise Virtual Array Hardware Configuration Guide 35

Enterprise Virtual Array Configurations

Figure 17 shows Fibre Channel loop 1A in the 42U rack with the expansion panel.
1 Controller pair
2 Expansion panel
3 Fibre Channel cable
4 FC drive enclosure

2
1
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

4 3

CXO7825B

Figure 17: 2C12D configuration—Fibre Channel loop 1A with expansion panel

36 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 18 shows Fibre Channel loop 1B in the 42U rack with the expansion panel.
1 Controller pair
2 Expansion panel
3 Fibre Channel cable
4 FC drive enclosure

2
1
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

4
3

CXO7826B

Figure 18: 2C12D configuration—Fibre Channel loop 1B with expansion panel

Enterprise Virtual Array Hardware Configuration Guide 37

Enterprise Virtual Array Configurations

Figure 19 shows Fibre Channel loop 2A in the 42U rack with the expansion panel.
1 Controller pair
2 FC drive enclosure
3 Fibre Channel cable
4 Expansion panel

1
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT
2

CXO7827B

Figure 19: 2C12D configuration—Fibre Channel loop 2A with expansion panel

38 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 20 shows Fibre Channel loop 2B in the 42U rack with the expansion panel.
1 Fibre Channel cable
2 Controller pair
3 FC drive enclosure
4 Expansion panel

3
1

4
2
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

CXO7828B

Figure 20: 2C12D configuration—Fibre Channel loop 2B with expansion panel

Cable Management Configurations

A configuration can have two different cable management configurations. If the configuration
uses FC loop switches, the configuration uses a combination of cable containment spools and a
cable management arm to organize the Fibre Channel cables. If the configuration uses
expansion panels, the configuration uses cable containment spools to organize the Fibre
Channel cables.

Cable Management Arms

When the configuration uses FC loop switches, the configuration contains two cable
management arms. All of the Fibre Channel cables in the configuration pass through one of the
cable management arms. Each cable management arm can hold several radial clips. Each
radial clip can hold a maximum of seven Fibre Channel cables. The cable management arms
can hold all of the Fibre Channel cables within a storage system configuration.
Each rack contains four flumes. These flumes are placed next to the cable management arms
on the left and right sides of the rack. Each flume guides the Fibre Channel cables from the
cable containment spools to the cable management arms.

Enterprise Virtual Array Hardware Configuration Guide 39

Enterprise Virtual Array Configurations

Cable Containment Spools

The cable containment spools hold the Fibre Channel cables. These cable containment spools
gather up extra cable length and guide the Fibre Channel cables from the FC drive enclosures
to the flumes located on the sides of the rack.
The number of cable containment spools varies by rack configuration. Racks with more FC
drive enclosures contain more cable containment spools.
The 2C12D configuration contains 12 cable containment spools and two cable management
arms. Figure 21 shows the cable management configuration for the 2C12D configuration.
1 Cable containment
spool
2 Fibre Channel cable
1 3 Cable management
arm
2 4 Radial clip

CXO7901B

Figure 21: 2C12D cable management configuration

40 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

2C6D Configuration
The 2C6D configuration is a single-rack configuration that provides a maximum of 3.1 TB (84
36.4-GB disks), 6.1 TB (84 72.8-GB disks), or 12.3 TB (84 146-GB disks) of storage capacity.
This configuration can contain a maximum of 84 disks.
The 2C6D configuration is available in either the 41U rack or the 42U rack. The 2C6D can
contain four FC loop switches or one expansion panel.

Enclosure Address Bus Configuration

The 2C6D configuration contains seven enclosure address bus junction boxes at 6U
increments in the left rear rail of the rack. Each FC drive enclosure should be connected to an
enclosure address bus junction box. The FC drive enclosures connect to each enclosure
address bus junction box in pairs. The controller pair connects to the enclosure address bus
junction box with a Y cable. Figure 22 shows the enclosure address bus cable configuration
for the 2C6D configuration.
1 Top terminator
1
2 Enclosure address bus
cable
3 Enclosure address 10
2
4 Enclosure address bus
junction box
5 Enclosure address 7
6 Enclosure address 1
3 7 Bottom terminator

4
5

7
CXO7902C

Figure 22: 2C6D configuration—enclosure address bus cables

Enterprise Virtual Array Hardware Configuration Guide 41

Enterprise Virtual Array Configurations

Fibre Channel Loop Configurations

The 2C6D configuration contains four Fibre Channel loops. A Fibre Channel loop is formed
when the FC drive enclosures and the controller pair are connected by Fibre Channel cables.
The 2C6D configuration can use an FC loop switch or an expansion panel to achieve the
desired Fibre Channel loop configuration. (Refer to “Fibre Channel Loop Configurations” on
page 31 for more information about the use of FC loop switches and expansion panels in the
FC loop configurations.)
Refer to Table 4 on page 31 for the locations of the Fibre Channel loops in a storage rack.
Figure 23, Figure 24, Figure 25, and Figure 26 show the 2C6D Fibre Channel loop
configurations with the FC loop switches. Figure 27, Figure 28, Figure 29, and Figure 30 show
the 2C6D Fibre Channel loop configurations with an expansion panel.
Figure 23 shows Fibre Channel loop 1A and the associated FC loop switch.
1 Controller-to-controller
Mirror port FC cable
2 Controller pair
3 FC loop switch
4 FC drive enclosure
5 Fibre Channel cable

1
2

CXO7903B

Figure 23: 2C6D configuration—Fibre Channel loop 1A with FC loop switch

42 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 24 shows Fibre Channel loop 1B and the associated FC loop switch.
1 Controller-to-controller
Mirror port FC cable
2 FC loop switch
3 Fibre Channel cable
4 FC drive enclosure
5 Controller pair

4
1
5

CXO7904B

Figure 24: 2C6D configuration—Fibre Channel loop 1B with FC loop switch

Enterprise Virtual Array Hardware Configuration Guide 43

Enterprise Virtual Array Configurations

Figure 25 shows Fibre Channel loop 2A and the associated FC loop switch.
1 Fibre Channel cable
2 FC loop switch
3 Controller-to-controller
Mirror port FC cable
4 FC drive enclosure
5 Controller pair

4 1

2
5 3

CXO7905B

Figure 25: 2C6D configuration—Fibre Channel loop 2A with FC loop switch

44 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 26 shows Fibre Channel loop 2B and the associated FC loop switch.
1 FC drive enclosure
2 Fibre Channel cable
3 FC loop switch
4 Controller pair
5 Controller-to-controller
Mirror port FC cable
1

3
4

CXO7906B

Figure 26: 2C6D configuration—Fibre Channel loop 2B with FC loop switch

Enterprise Virtual Array Hardware Configuration Guide 45

Enterprise Virtual Array Configurations

Figure 27 shows Fibre Channel loop 1A in the 42U rack with the expansion panel.
1 Controller pair
2 Expansion panel

2
1
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

CXO7907A

Figure 27: 2C6D configuration—Fibre Channel loop 1A with expansion panel

46 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 28 shows Fibre Channel loop 1B in the 42U rack with the expansion panel.
1 Controller pair
2 Expansion panel

2
1
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

CXO7908A

Figure 28: 2C6D configuration—Fibre Channel loop 1B with expansion panel

Enterprise Virtual Array Hardware Configuration Guide 47

Enterprise Virtual Array Configurations

Figure 29 shows Fibre Channel loop 2A in the 42U rack with the expansion panel.
1 Controller pair
2 Expansion panel

1
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

CXO7909A

Figure 29: 2C6D configuration—Fibre Channel loop 2A with expansion panel

48 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 30 shows Fibre Channel loop 2B in the 42U rack with the expansion panel.
1 Controller pair
2 Expansion panel

2
1
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

CXO7910A

Figure 30: 2C6D configuration—Fibre Channel loop 2B with expansion panel

Enterprise Virtual Array Hardware Configuration Guide 49

Enterprise Virtual Array Configurations

Cable Management Configurations

The 2C6D configuration contains six cable containment spools and two cable management
arms.
Please see “Cable Management Configurations” on page 39 for more information about cable
containment spools and cable management arms.
Figure 31 shows the cable management configuration in the 2C6D configuration.
1 Cable containment spool
2 Fibre Channel cable
3 Cable management arm
4 Radial clip

CXO7911B

Figure 31: 2C6D cable management configuration

50 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

8C8D Configuration
The 8C8D configuration is a single-rack configuration that provides a maximum of 4.1 TB
(112 36.4-GB disks), 8.2 TB (112 72.8-GB disks), or 16.4 TB (112 146-GB disks) of storage
capacity. This configuration can contain a maximum of 112 disks.
The 8C8D configuration is available in either the 41U rack or the 42U rack.

Enclosure Address Bus Configuration

The 8C8D configuration contains seven enclosure address bus junction boxes at 6U
increments in the left rear rail of the rack. Each FC drive enclosure should be connected to an
enclosure address bus junction box. The FC drive enclosures connect to each enclosure
address bus junction box in pairs. The controller pairs connect to the enclosure address bus
junction boxes with a Y cable. Figure 32 shows the enclosure address bus cable configuration
for the 8C8D configuration.
1 Terminator
1 2 Enclosure address 1
3 Enclosure address 3
4 Enclosure address bus
junction box
5 Enclosure address bus
cable

1
CXO7912B

Figure 32: 8C8D configuration—enclosure address bus cables

Enterprise Virtual Array Hardware Configuration Guide 51

Enterprise Virtual Array Configurations

Fibre Channel Loop Configurations

The 8C8D configuration contains 16 Fibre Channel loops. A Fibre Channel loop is formed
when the FC drive enclosures and the controller pair are connected by Fibre Channel cables.
The 8C8D configuration does not use FC loop switches or expansion panels. Instead, each I/O
port on an FC drive enclosure is connected directly to a controller with a Fibre Channel cable.
Figure 33 shows the four 1A Fibre Channel loops.
1 Controller pair
2 FC drive enclosure
3 Fibre Channel cable
1

1
3

CXO7913B

Figure 33: 8C8D configuration—Fibre Channel loop 1A

52 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 34 shows the four 1B Fibre Channel loops.

1 Controller pair
2 FC drive enclosure
3 Fibre Channel cable

1
3

CXO7914B

Figure 34: 8C8D configuration—Fibre Channel loop 1B

Enterprise Virtual Array Hardware Configuration Guide 53

Enterprise Virtual Array Configurations

Figure 35 shows the four 2A Fibre Channel loops.

1 Controller pair
2 FC drive enclosure
3 Fibre Channel cable

2 3

CXO7915B

Figure 35: 8C8D configuration—Fibre Channel loop 2A

54 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 36 shows the four 2B Fibre Channel loops.

1 Controller pair
2 FC drive enclosure
3 Fibre Channel cable

3 2

CXO7916B

Figure 36: 8C8D configuration—Fibre Channel loop 2B

Enterprise Virtual Array Hardware Configuration Guide 55

Enterprise Virtual Array Configurations

Cable Management Configurations

The 8C8D configuration contains eight cable containment spools and no cable management
arms.
Please see “Cable Management Configurations” on page 39 for more information about cable
containment spools and cable management arms.
Figure 37 shows the cable management configuration in the 8C8D configuration.
1 Cable containment spool
2 Fibre Channel cable

CXO7917B

Figure 37: 8C8D cable management configuration

56 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

2C2D Configuration
The 2C2D configuration is a single-rack configuration that provides a maximum of 1.0 TB (28
36.4-GB disks), 2.0 TB (28 72.8-GB disks), or 4.1 TB (28 146-GB disks) of storage capacity.
This configuration can contain a maximum of 28 disks. You can expand the capacity of the
2C2D configuration by adding more drive enclosures and four FC loop switches.
The 2C2D configuration is available in the 41U rack.

Enclosure Address Bus Configuration

The 2C2D configuration contains seven enclosure address bus junction boxes at 6U
increments in the left rear rail of the rack. Each FC drive enclosure should be connected to an
enclosure address bus junction box. The FC drive enclosures connect to each enclosure
address bus junction box in pairs. The controller pair connects to the enclosure address bus
junction boxes with a Y cable. Figure 38 shows the enclosure address bus cable configuration
for the 2C2D configuration.
1 Bottom terminator
6 2 Enclosure address 1
3 Enclosure address bus
cable
4 Enclosure address 7
5 5 Enclosure address
junction box
6 Top terminator

1
CXO8041C

Figure 38: 2C2D configuration—enclosure address bus cables

Enterprise Virtual Array Hardware Configuration Guide 57

Enterprise Virtual Array Configurations

Fibre Channel Loop Configurations

The 2C2D configuration contains four Fibre Channel loops. A Fibre Channel loop is formed
when the FC drive enclosures and the controller pair are connected by Fibre Channel cables.
The 2C2D configuration does not use FC loop switches or expansion panels. Instead, each I/O
port on an FC drive enclosure is connected directly to a controller with a Fibre Channel cable.
Refer to Table 4 on page 31 for the locations of the Fibre Channel loops in a storage rack.
Figure 39 shows Fibre Channel loop 1A.
1 Controller-to-controller
Mirror port FC cable
2 HSV110 controller pair
3 FC drive enclosure
4 Fibre Channel cable

2 1

CXO8042B

Figure 39: 2C2D configuration—Fibre Channel loop 1A

58 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 40 shows Fibre Channel loop 1B.

1 Controller-to-controller
Mirror port FC cable
2 HSV110 controller pair
3 FC drive enclosure
4 Fibre Channel cable

1 2

CXO8043B

Figure 40: 2C2D configuration—Fibre Channel loop 1B

Enterprise Virtual Array Hardware Configuration Guide 59

Enterprise Virtual Array Configurations

Figure 41 shows Fibre Channel loop 2A.

1 Controller-to-controller
Mirror port FC cable
2 HSV110 controller pair
3 FC drive enclosure
4 Fibre Channel cable

2 1

CXO8044B

Figure 41: 2C2D configuration—Fibre Channel loop 2A

60 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 42 shows Fibre Channel loop 2B.

1 Controller-to-controller
Mirror port FC cable
2 HSV110 controller pair
3 FC drive enclosure
4 Fibre Channel cable

3
4

1 2

CXO8045B

Figure 42: 2C2D configuration—Fibre Channel loop 2B

Enterprise Virtual Array Hardware Configuration Guide 61

Enterprise Virtual Array Configurations

Cable Management Configurations

The 2C2D configuration contains four cable containment spools and no cable management
arms.
Please see “Cable Management Configurations” on page 39 for more information about cable
containment spools and cable management arms.
Figure 43 shows the cable management configuration for the 2C2D configuration.
1 Cable containment
spool
2 Fibre Channel cable

2
1

CXO8046A

Figure 43: 2C2D cable management configuration

62 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

2C12D + 0C6D Configuration

The 2C12D + 0C6D configuration is a dual-rack configuration that provides up to 8.7 TB (240
36.4-GB disks), 17.5 TB (240 72.8-GB disks), or 35 TB (240 146-GB disks) of storage
capacity by expanding from 168 disks to 240 disks. The 0C6D rack connects to the 2C12D
rack with enclosure address bus cables and Fibre Channel cables.

Enclosure Address Bus Configuration

Each rack contains enclosure address bus junction boxes at 6U increments in the left rear rail
of the rack. The 0C6D rack contains six enclosure address bus junction boxes; however, the
FC drive enclosures use only three of the enclosure address bus junction boxes. The 2C12D
rack contains seven enclosure address bus junction boxes. The FC drive enclosures and
controller pair in the 2C12D rack use all seven enclosure address bus junction boxes.
The two racks are connected by one enclosure address bus cable, which connects to the bottom
enclosure address bus junction box on each rack. The enclosure address bus cable between the
racks is polarized. The P1 end of the cable connects to the bottom enclosure address bus
junction box on the 2C12D rack. The P2 end of the cable connects to the bottom enclosure
address bus junction box on the 0C6D rack.

Note: Make sure the P1 end of the enclosure address bus cable is plugged into the 2C12D rack
and the P2 end of the enclosure address bus cable is plugged into the 0C6D rack. If the cable is
connected to the racks incorrectly, Command View EVA places the FC drive enclosures in the
Unmappable Hardware folder.

In order to connect two racks with an enclosure address bus cable, the HP Authorized Service
Representative will have to remove the bottom terminator on the master rack (2C12D rack).

Enterprise Virtual Array Hardware Configuration Guide 63

Enterprise Virtual Array Configurations

Figure 44 shows the enclosure address bus cable configuration in the 2C12D + 0C6D
configuration.
1 Top terminator
1 2 Enclosure
address bus
junction box
3 Enclosure
address 07
4 Enclosure
address bus
cable
5 Enclosure
address 01
6 P1 end of
rack-to-rack
enclosure
address bus
2 cable
3 7 5-meter
rack-to-rack
enclosure
1 address bus
cable
8 P2 end of
4 rack-to-rack
enclosure
address bus
9 cable
9 Enclosure
address 17
5

8 6

7
CXO7918C

Figure 44: 2C12D + 0C6D configuration—enclosure address bus cables

Fibre Channel Loop Configurations

The 2C12D + 0C6D configuration contains four Fibre Channel loops. A Fibre Channel loop is
formed when the FC drive enclosures and the controller pair are connected by Fibre Channel
cables. The 2C12D configuration can use an FC loop switch or expansion panels to achieve
the desired Fibre Channel loop configuration.
When the 2C12D + 0C6D configuration uses FC loop switches, each FC drive enclosure in a
loop is directly connected to the associated FC loop switch. The controller pair is also
connected directly to the associated FC loop switch. When the FC loop switch is powered on,
it completes a Fibre Channel loop.
When the 2C12D + 0C6D configuration uses expansion panels, all of the FC drive enclosures
in a loop are connected to the controller pair in the master rack. The 2C12D + 0C6D
configuration uses expansion panels to achieve this configuration.
Refer to Table 4 on page 31 for locations of Fibre Channel loops in a storage rack.

64 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 45 shows Fibre Channel loop 1A and the associated FC loop switch.
1 Controller-to-controller
Mirror port FC cable
2 Controller pair
3 FC loop switch
4 FC drive enclosure
5 Fibre Channel cable

1
2
3
4

CXO7919B

Figure 45: 2C12D + 0C6D configuration—Fibre Channel loop 1A with FC loop switch

Enterprise Virtual Array Hardware Configuration Guide 65

Enterprise Virtual Array Configurations

Figure 46 shows Fibre Channel loop 1B and the associated FC loop switch.
1 Controller pair
2 Controller-to-controller
Mirror port FC cable
3 FC loop switch
4 FC drive enclosure
5 Fibre Channel cable

2
1
3
4

CXO7920B

Figure 46: 2C12D + 0C6D configuration—Fibre Channel loop 1B with FC loop switch

66 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 47 shows Fibre Channel loop 2A and the associated FC loop switch.
1 FC drive enclosure
2 Fibre Channel cable
3 FC loop switch
4 Controller pair
1 5 Controller-to-controller
Mirror port FC cable

3
5
4

CXO7921B

Figure 47: 2C12D + 0C6D configuration—Fibre Channel loop 2A with FC loop switch

Enterprise Virtual Array Hardware Configuration Guide 67

Enterprise Virtual Array Configurations

Figure 48 shows Fibre Channel loop 2B and the associated FC loop switch.
1 Fibre Channel cable
2 FC loop switch
3 Controller-to-controller
Mirror port FC cable
4 FC drive enclosure
5 Controller pair

1 4

2
5
3

CXO7922B

Figure 48: 2C12D + 0C6D configuration—Fibre Channel loop 2B with FC loop switch

68 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 49 shows Fibre Channel loop 1A with expansion panels.

1 6

3
Master
2
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

4 7

1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

Expansion
5
7

CXO7813B

1 Master rack
2 Controller pair
3 Master rack expansion panel
4 5-meter rack-to-rack Fibre Channel cables
5 Expansion rack expansion panel
6 Expansion rack
7 FC drive enclosure
Figure 49: 2C12D + 0C6D configuration—Fibre Channel loop 1A with expansion panels

Enterprise Virtual Array Hardware Configuration Guide 69

Enterprise Virtual Array Configurations

Figure 50 shows Fibre Channel Loop 1B with expansion panels.

1 6

3
2 Master
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

Expansion
5
7 7

CXO7814B

1 Master rack
2 Controller pair
3 Master rack expansion panel
4 5-meter rack-to-rack Fibre Channel cables
5 Expansion rack expansion panel
6 Expansion rack
7 FC drive enclosure
Figure 50: 2C12D + 0C6D configuration—Fibre Channel Loop 1B with expansion panels

70 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 51 shows Fibre Channel Loop 2A with expansion panels.

1 6

2 Master
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

3 4

1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

Expansion
5
7 7

CXO7815B

1 Master rack
2 Controller pair
3 Master rack expansion panel
4 5-meter rack-to-rack Fibre Channel cables
5 Expansion rack expansion panel
6 Expansion rack
7 FC drive enclosure
Figure 51: 2C12D + 0C6D configuration—Fibre Channel loop 2A with expansion panels

Enterprise Virtual Array Hardware Configuration Guide 71

Enterprise Virtual Array Configurations

Figure 52 shows Fibre Channel Loop 2B with expansion panels.

1 6

3
2 Master
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

Expansion
5
7 7

CXO7816B

1 Master rack
2 Controller pair
3 Master rack expansion panel
4 5-meter rack-to-rack Fibre Channel cables
5 Expansion rack expansion panel
6 Expansion rack
7 FC drive enclosure
Figure 52: 2C12D + 0C6D configuration—Fibre Channel loop 2B with expansion panels

72 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

2 x 2C12D + 0C12D Configuration

The 2 x 2C12D + 0C12D configuration is a triple-rack configuration that can provide up to
17.5 TB (480 36.4-GB disks), 34.9 TB (480 72.8-GB disks), or 70 TB (480 146-GB disks) of
storage capacity by expanding each Enterprise Virtual Array to 240 disks each for a total of
480 disks. The two 2C12D master racks connect to the 0C12D expansion rack with enclosure
address bus and Fibre Channel cables.

Enclosure Address Bus Configuration

Each rack contains enclosure address bus junction boxes at 6U increments in the left rear rail
of the rack. The 0C12D rack contains six enclosure address bus junction boxes. The FC drive
enclosures in the 0C12D rack use all six enclosure address bus junction boxes. The 2C12D
rack contains seven enclosure address bus junction boxes. The FC drive enclosures and
controller pair in the 2C12D rack use all seven enclosure address bus junction boxes.
The three racks are connected by two enclosure address bus cables. Each master rack is
connected to the expansion rack by one enclosure address bus cable. One master rack runs an
enclosure address bus cable to the bottom enclosure address bus junction box on the expansion
rack; the other master rack runs an enclosure address bus cable to the fourth enclosure address
bus junction box (from the bottom) on the expansion rack.
The enclosure address bus cables are polarized. The P1 end of the cable connects to the bottom
enclosure address bus junction box on the 2C12D rack. The P2 end of the cable connects to the
enclosure address bus junction box on the expansion rack.

Note: Make sure the P1 end of the enclosure address bus cable is plugged into the 2C12D rack
and the P2 end of the enclosure address bus cable is plugged into the expansion rack. If the cable
is connected to the racks incorrectly, Command View EVA places the FC drive enclosures in the
Unmappable Hardware folder.

In order to connect the racks with an enclosure address bus cable, the HP Authorized Service
Representative will have to remove the bottom terminator on the master racks (2C12D rack).

Enterprise Virtual Array Hardware Configuration Guide 73

Enterprise Virtual Array Configurations

Figure 53 shows the enclosure address bus cable configuration in the 2C12D + 0C12D
configuration.

1 1

1
2 10

7
3

6 6
CXO7923C

1 Top terminator
2 Enclosure address bus cable
3 Enclosure address 7
4 Enclosure address 1
5 P1 end of rack-to-rack enclosure address bus cable
6 5-meter rack-to-rack enclosure address bus cable
7 P2 end of rack-to-rack enclosure address bus cable
8 Enclosure address 15
9 Enclosure address junction box
- FC drive enclosure
Figure 53: 2 x 2C12D + 0C12D configuration—enclosure address bus cables

Fibre Channel Loop Configurations

The 2 x 2C12D + 0C12D configuration contains eight Fibre Channel loops. A Fibre Channel
loop is formed when the FC drive enclosures and the controller pair are connected by Fibre
Channel cables. The 2 x 2C12D + 0C12D configuration can use an FC loop switch or
expansion panels to achieve the desired Fibre Channel loop configuration.
The 0C12D rack is divided into an upper and lower half. The upper half of the 0C12D rack
connects to the master rack on the right (when viewed from the rear), and the lower half of the
0C12D rack connects to the master rack on the left (when viewed from the rear).

74 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

When the 2 x 2C12D + 0C12D configuration uses FC loop switches, each FC drive enclosure
in a loop is directly connected to the associated FC loop switch. The controller pair is also
connected directly to the associated FC loop switch. When the FC loop switch is powered on,
it completes a Fibre Channel loop.
When the 2 x 2C12D + 0C12D configuration uses expansion panels, all of the FC drive
enclosures in a loop are connected to the controller pair in the master rack. The 2 x 2C12D +
0C12D configuration uses expansion panels to achieve this configuration.
Refer to Table 4 on page 31 for locations of Fibre Channel loops in a storage rack.
Figure 54 shows the two 1A Fibre Channel loops and the associated FC loop switches.

1
2
3
4

CXO7924B

1 Controller-to-controller Mirror port FC cable

2 Controller pair
3 FC loop switch
4 FC drive enclosure
5 Fibre Channel cable
Figure 54: 2 x 2C12D + 0C12D configuration—Fibre Channel loop 1A with FC loop switch

Enterprise Virtual Array Hardware Configuration Guide 75

Enterprise Virtual Array Configurations

Figure 55 shows the two 1B Fibre Channel loops and the associated FC loop switches.

1
3
2
4

CXO7925B

1 Controller pair
2 Controller-to-controller Mirror port FC cable
3 FC loop switch
4 FC drive enclosure
5 Fibre Channel cable
Figure 55: 2 x 2C12D + 0C12D configuration—Fibre Channel loop 1B with FC loop switch

76 Enterprise Virtual Array Hardware Configuration Guide

 Enterprise Virtual Array Configurations

Figure 56 shows the two 2A Fibre Channel loops and the associated FC loop switches.

CXO7926B

1 FC drive enclosure
2 Fibre Channel cable
3 FC loop switch
4 Controller pair
5 Controller-to-controller Mirror port FC cable
Figure 56: 2 x 2C12D + 0C12D configuration—Fibre Channel loop 2A with FC loop switch

Enterprise Virtual Array Hardware Configuration Guide 77

Enterprise Virtual Array Configurations

Figure 57 shows the two 2B Fibre Channel loops and the associated FC loop switches.

2
5
3

CXO7927B

1 Fibre Channel cable

2 FC loop switch
3 Controller-to-controller Mirror port FC cable
4 FC drive enclosure
5 Controller pair
Figure 57: 2 x 2C12D + 0C12D configuration—Fibre Channel loop 2B with FC loop
switch

78 Enterprise Virtual Array Hardware Configuration Guide

 Figure 58 shows the two 1A Fibre Channel loops with expansion panels.

79
Enterprise Virtual Array Configurations

1 6 1
7
Master Expansion
2 2
1B 2B 1A 2A 1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT
3 4 5 4
1B 2B 1A 2A 1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT
Expansion Master
5 3
7

Enterprise Virtual Array Hardware Configuration Guide

CXO7818B
1 Master rack
2 Controller pair
3 Master rack expansion panel
4 5-meter rack-to-rack Fibre Channel cables
5 Expansion rack expansion panel
6 Expansion rack
7 FC drive enclosure
Figure 58: 2 x 2C12D + 0C12D configuration—Fibre Channel loop 1A with expansion panels
 Figure 59 shows the two 1B Fibre Channel loops with expansion panels.

80
1 6 1

7
Enterprise Virtual Array Configurations

2 Master Expansion 2
1B 2B 1A 2A 1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT

4 3 4 5
1B 2B 1A 2A 1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT

Expansion Master
5 3

CXO7819B

1 Master rack
2 Controller pair
3 Master rack expansion panel
4 5-meter rack-to-rack Fibre Channel cables
5 Expansion rack expansion panel
6 Expansion rack
7 FC drive enclosure
Figure 59: 2 x 2C12D + 0C12D configuration—Fibre Channel loop 1B with expansion panels

Enterprise Virtual Array Hardware Configuration Guide

 Figure 60 shows the two 2A Fibre Channel loops with expansion panels.

81
Enterprise Virtual Array Configurations

1 6 1
7
Master Expansion
2 2
1B 2B 1A 2A 1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT
3 4 5 4
1B 2B 1A 2A 1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT
Expansion Master
5 3
7

Enterprise Virtual Array Hardware Configuration Guide

CXO7820B
1 Master rack
2 Controller pair
3 Master rack expansion panel
4 5-meter rack-to-rack Fibre Channel cables
5 Expansion rack expansion panel
6 Expansion rack
7 FC drive enclosure
Figure 60: 2 x 2C12D + 0C12D configuration—Fibre Channel loop 2A with expansion panels
82
Figure 61 shows the two 2B Fibre Channel loops with expansion panels.

1 6 1

7
Enterprise Virtual Array Configurations

2 Master Expansion 2
1B 2B 1A 2A 1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT

3 4 5 4

1B 2B 1A 2A 1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT

Expansion Master
5 3

CXO7821B

1 Master rack
2 Controller pair
3 Master rack expansion panel
4 5-meter rack-to-rack Fibre Channel cables
5 Expansion rack expansion panel
6 Expansion rack
7 FC drive enclosure
Figure 61: 2 x 2C12D + 0C12D configuration—Fibre Channel loop 2B with expansion panels

Enterprise Virtual Array Hardware Configuration Guide

Upgrading Existing Racks to
Enterprise v2.0
3
This chapter summarizes how to upgrade an Enterprise Virtual Array v1.0 configuration to an
Enterprise Virtual Array v2.0 configuration. The key differences between an Enterprise
Virtual Array v1.0 configuration and an Enterprise Virtual Array v2.0 configuration are the
absence of expansion panels, the addition of FC loop switches, and the reconfiguration of the
Fibre Channel cables.
This chapter contains the following sections:
■ Expansion Panels, page 85
■ FC Loop Switches, page 85
■ Fibre Channel Cable Reconfiguration, page 85

Note: Only HP Authorized Service Representatives may upgrade Enterprise Virtual Array v1.0
configurations to Enterprise Virtual Array v2.0 configurations.

Before you upgrade an Enterprise Virtual Array v1.0 configuration to an Enterprise Virtual
Array v2.0 configuration, ensure that you have the correct Enterprise Virtual Array software
and firmware.
Refer to HP StorageWorks Enterprise Virtual Array Changing EVA Versions Instructions for
more information.

Enterprise Virtual Array Hardware Configuration Guide 83

Upgrading Existing Racks to Enterprise v2.0

Figure 62 shows the 2C12D configuration for the Enterprise Virtual Array v1.0 and the for
Enterprise Virtual Array v2.0. In general, v2.0 racks are characterized by the presence of the
FC loop switches. Enterprise v1.0 racks are 42U, while v2.0 racks can be either 41U or 42U.

Note: Enterprise Virtual Array v3.0 racks use the same configurations as the Enterprise Virtual
Array v2.0 racks.

V1
V2

1 6

3
3

5 5
4
2
2
4 5 5

CXO7974A

1 42U rack
2 Controller pair
3 FC drive enclosure
4 Expansion panels
5 FC loop switches
6 41U rack
Figure 62: Expansion panels versus FC loop switches

84 Enterprise Virtual Array Hardware Configuration Guide

 Upgrading Existing Racks to Enterprise v2.0

Expansion Panels
In Version 1.0 of the Enterprise Virtual Array, expansion panels were added to racks to allow
you to expand the storage capacity of the Enterprise Virtual Array. In Version 2.0 of the
Enterprise Virtual Array, the presence of FC loop switches has made the expansion panels
obsolete. You can easily expand an Enterprise Virtual Array configuration by directly
connecting additional FC drive enclosures to the FC loop switches.
Your HP Authorized Service Representative is responsible for removing expansion panels.

FC Loop Switches
An Enterprise Virtual Array master rack contains four FC loop switches. Typically, two FC
loop switches are mounted on a rack shelf above the controller pair, and two FC loop switches
are mounted on a rack shelf below the controller pair.
Your HP Authorized Service Representative is responsible for installing FC loop switches.

Fibre Channel Cable Reconfiguration

The Fibre Channel cable configuration on a rack that uses FC loop switches differs from the
Fibre Channel cable configuration on a rack that uses expansion panels. When a rack uses an
expansion panel, the FC drive enclosures are linked together in a chain and connected to the
controllers via the expansion panel. When a rack uses FC loop switches, the FC drive
enclosures and the controllers are linked directly to the FC loop switch.
Your HP Authorized Service Representative is responsible for reconfiguring the Fibre
Channel loops.

Enterprise Virtual Array Hardware Configuration Guide 85

Upgrading Existing Racks to Enterprise v2.0

Figure 63 shows the 2C12D Fibre Channel loop 1A configurations for both a v1.0
configuration and a v2.0 configuration.

V1
V2

1
5

3 4
2
2
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT 4

CXO7975A

1 42U rack
2 Controller pair
3 Expansion panel
4 FC loop switch
5 41U rack
Figure 63: Fibre Channel cabling comparison— Enterprise v1.0 to Enterprise v2.0

86 Enterprise Virtual Array Hardware Configuration Guide

Expanding a Rack 4
This chapter summarizes how to add new FC drive enclosures to a storage rack and describes
the placement of controllers, FC drive enclosures, FC loop switches, enclosure address bus
junction boxes and cables, and Fibre Channel cables.
This chapter contains the following sections:
■ Adding FC Drive Enclosures to a Rack, page 88
■ 2C6D + 6D Configuration, page 89
■ 0C6D + 6D Configuration, page 99
Only HP Authorized Service Representatives may expand the 2C6D and 0C6D racks. The
2C6D and 0C6D racks may be expanded by adding FC drive enclosures, Fibre Channel cables,
and enclosure address bus cables to the existing racks. In general, the FC drive enclosures are
added in pairs.
The 2C6D rack can be expanded to the following:
■ 2C6D + 2D (expands the 2C6D rack to 112 disks)
■ 2C6D + 4D (expands the 2C6D rack to 140 disks)
■ 2C6D + 6D (expands the 2C6D rack to 168 disks)
The 0C6D rack can be expanded to the 0C12D rack.

Enterprise Virtual Array Hardware Configuration Guide 87

Expanding a Rack

Adding FC Drive Enclosures to a Rack

An HP Authorized Service Representative can add FC drive enclosures to a rack while the
Enterprise Virtual Array is on or off. HP highly recommends that the Enterprise Virtual Array
is turned off, while adding FC drive enclosures to a rack. If the HP Authorized Service
Representative would like to add an FC drive enclosure to the rack with the power on, the
service representative should take care to disconnect and connect one Fibre Channel loop at a
time.
Adding FC drive enclosures involves placing the drive enclosures in the rack, connecting the
drive enclosures to the enclosure address bus and the power outlets, and correctly adding the
drive enclosures to the FC loops.

Note: An HP Authorized Service Representative must add the FC drive enclosures to the rack. Do
not attempt to do add an FC drive enclosure without first seeking guidance and assistance from an
HP Authorized Service Representative.

2C6D Configuration
The 2C6D configuration contains up to six FC drive enclosures (84 disks). This configuration
is shown in Figure 64.
1 3U blank
2 FC drive enclosure
3 FC loop switch
1
4 Controller pair

3
4
3

CXO7874B

Figure 64: 2C6D configuration

88 Enterprise Virtual Array Hardware Configuration Guide

 Expanding a Rack

2C6D + 6D Configuration
The 2C6D + 6D configuration provides up to twelve FC drive enclosures (168 disks). It
upgrades a 2C6D configuration to a 2C12D configuration.

Note: This configuration is only available with assistance from an HP Authorized Service
Representative.

Enclosure Address Bus Configuration

Each FC drive enclosure should be connected to an enclosure address bus junction box. The
FC drive enclosures connect to each enclosure address bus junction box in pairs. The
controller pair connects to the enclosure address bus junction box with a Y cable. Figure 65
shows the enclosure address bus cable configuration for the 2C6D + 6D configuration.
1 Bottom terminator
7 2 Enclosure address 1
6 3 Enclosure address bus
cable
4 Enclosure address 7
5 Enclosure address bus
junction box
6 Enclosure address 13
7 Top terminator

5
4

2
1

CXO7885C

Figure 65: 2C6D + 6D configuration—enclosure address cables

Enterprise Virtual Array Hardware Configuration Guide 89

Expanding a Rack

Fibre Channel Loop Configurations

The 2C6D + 6D configuration contains four Fibre Channel loops. A Fibre Channel loop is
formed when the FC drive enclosures and the controller pair are connected by Fibre Channel
cables. The 2C6D + 6D configuration can use an FC loop switch or an expansion panel to
achieve the desired Fibre Channel loop configuration.
When the 2C6D + 6D configuration uses FC loop switches, each FC drive enclosure in a loop
is directly connected to the associated FC loop switch. The controller pair is also connected
directly to the associated FC loop switch. When the FC loop switch is powered on, it
completes a Fibre Channel loop.
When the 2C6D + 6D configuration uses an expansion panel, a Fibre Channel loop is
accomplished by connecting two FC drive enclosures directly to the controllers and linking
each FC drive enclosure together in a chain.
Table 5 provides the locations for the Fibre Channel loops in a storage rack.
Table 5: Fibre Channel Loop Locations in Rack
Fibre
Channel Location in Rack
Loop (viewed from rear)
1A lower right side
1B lower left side
2A upper right side
2B upper left side

Figure 66 shows Fibre Channel loop 1A and the associated FC loop switch.

90 Enterprise Virtual Array Hardware Configuration Guide

 Expanding a Rack

1 Controller-to-controller
Mirror port FC cable
2 Controller pair
3 FC loop switch
4 FC drive enclosure
5 Fibre Channel cable

1
2

CXO7886B

Figure 66: 2C6D + 6D configuration—Fibre Channel loop 1A with FC loop switch

Enterprise Virtual Array Hardware Configuration Guide 91

Expanding a Rack

Figure 67 shows Fibre Channel loop 1B and the associated FC loop switch.
1 Controller pair
2 Controller-to-controller
Mirror port FC cable
3 FC loop switch
4 FC drive enclosure
5 Fibre Channel cable

2
1
3
4

CXO7887B

Figure 67: 2C6D + 6D configuration—Fibre Channel loop 1B with FC loop switch

92 Enterprise Virtual Array Hardware Configuration Guide

 Expanding a Rack

Figure 68 shows Fibre Channel loop 2A and the associated FC loop switch.
1 FC drive enclosure
2 Fibre Channel cable
3 FC loop switch
1 4 Controller pair
5 Controller-to-controller
Mirror port FC cable

3
5
4

CXO7888B

Figure 68: 2C6D + 6D configuration—Fibre Channel loop 2A with FC loop switch

Enterprise Virtual Array Hardware Configuration Guide 93

Expanding a Rack

Figure 69 shows Fibre Channel loop 2B and the associated FC loop switch.
1 Fibre Channel cable
2 FC loop switch
3 Controller-to-controller
Mirror port FC cable
4 FC drive enclosure
5 Controller pair

1 4

2
5
3

CXO7889B

Figure 69: 2C6D + 6D configuration—Fibre Channel loop 2B with FC loop switch

94 Enterprise Virtual Array Hardware Configuration Guide

 Expanding a Rack

Figure 70 shows Fibre Channel loop 1A with the expansion panel.

1 Controller pair
2 Expansion panel
3 Fibre Channel cable
4 FC drive enclosure

2
1
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

4 3

CXO7825B

Figure 70: 2C6D + 6D configuration—Fibre Channel loop 1A with expansion panel

Enterprise Virtual Array Hardware Configuration Guide 95

Expanding a Rack

Figure 71 shows Fibre Channel loop 1B with an expansion panel.

1 Controller pair
2 Expansion panel

2
1
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

4
3

CXO7826B

Figure 71: 2C6D + 6D configuration—Fibre Channel loop 1B with expansion panel

96 Enterprise Virtual Array Hardware Configuration Guide

 Expanding a Rack

Figure 72 shows Fibre Channel loop 2A with an expansion panel.

1 Controller pair
2 FC drive enclosure
3 Fibre Channel cable
4 Expansion panel

1
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT
2

CXO7827B

Figure 72: 2C6D + 6D configuration—Fibre Channel loop 2A with expansion panel

Enterprise Virtual Array Hardware Configuration Guide 97

Expanding a Rack

Figure 73 shows Fibre Channel loop 2B with an expansion panel.

1 Fibre Channel cable
2 Controller pair
3 FC drive enclosure
4 Expansion panel

3
1

4
2
1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

CXO7828B

Figure 73: 2C6D + 6D configuration—Fibre Channel loop 2B with expansion panel

98 Enterprise Virtual Array Hardware Configuration Guide

 Expanding a Rack

0C6D + 6D Configuration
The 0C6D + 6D configuration can support two controller pairs, and allows each controller pair
to support a maximum of 240 disks.

Enclosure Address Bus Configuration

Each FC drive enclosure should be connected to an enclosure address bus junction box. The
FC drive enclosures connect to each enclosure address bus junction box in pairs. Figure 74
shows the enclosure address bus cable configuration for the 0C6D + 6D configuration.
1 Terminator
2 Enclosure address bus
junction box
1
3 Bottom terminator (This
terminator is removed to
connect the expansion
rack to the master rack.)

CXO7933A

Figure 74: 0C6D + 6D configuration—enclosure address bus cables

Fibre Channel Loop Configurations

The 0C6D + 6D configuration contains eight Fibre Channel loops. A Fibre Channel loop is
formed when the FC drive enclosures and the controller pair are connected by Fibre Channel
cables. The 0C6D + 6D configuration can use an FC loop switch or expansion panels to
achieve the desired Fibre Channel loop configuration.
The 0C6D + 6D rack is divided into an upper and lower half. The upper half of the 0C12D
rack connects to one master rack, and the lower half of the 0C12D rack connects to another
master rack.

Enterprise Virtual Array Hardware Configuration Guide 99

Expanding a Rack

When the 0C6D + 6D configuration uses FC loop switches, each FC drive enclosure in a loop
is directly connected to the associated FC loop switch on the master rack. The controller pair is
also connected directly to the associated FC loop switch. When the FC loop switch is powered
on, it completes a Fibre Channel loop.
When the 0C6D + 6D configuration uses expansion panels, all of the FC drive enclosures in a
loop are connected to the controller pair in the master rack. The 0C6D + 6D configuration uses
expansion panels to achieve this configuration.
Figure 75 shows the two 1A Fibre Channel loops.
1 FC cable
Each FC cable is
2 connected to the 1A FC
loop switch in the master
rack.
2 FC drive enclosure
1

CXO7934A

Figure 75: 0C6D + 6D configuration—Fibre Channel loop 1A

100 Enterprise Virtual Array Hardware Configuration Guide

 Expanding a Rack

Figure 76 shows the two 1B Fibre Channel loops.

1 FC cable
2 Each FC cable is connected
to the 1B FC loop switch in
the master rack.
2 FC drive enclosure
1

CXO7935A

Figure 76: 0C6D + 6D configuration—Fibre Channel loop 1B

Enterprise Virtual Array Hardware Configuration Guide 101

Expanding a Rack

Figure 77 shows the two 2A Fibre Channel loops.

1 FC cable
Each FC cable is connected
to the 2A FC loop switch in
the master rack.
2 FC drive enclosure

CXO7936A

Figure 77: 0C6D + 6D configuration—Fibre Channel loop 2A

102 Enterprise Virtual Array Hardware Configuration Guide

 Expanding a Rack

Figure 78 shows the two 2B Fibre Channel loops.

1 FC cable
Each FC cable is connected
to the 2B FC loop switch in
the master rack.
2 FC drive enclosure

CXO7937A

Figure 78: 0C6D + 6D configuration—Fibre Channel loop 2B

Enterprise Virtual Array Hardware Configuration Guide 103

Expanding a Rack

Figure 79 shows the two 1A Fibre Channel loops and the expansion panels.
1 Expansion panel
2 5-meter Fibre Channel
cables that connect to
the master rack.

2
1

1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

Expansion

1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

Expansion

CXO7830A

Figure 79: 0C6D + 6D configuration—Fibre Channel loop 1A with expansion panels

104 Enterprise Virtual Array Hardware Configuration Guide

 Expanding a Rack

Figure 80 shows the two 1B Fibre Channel loops and the expansion panels.
1 Expansion panel
2 5-meter Fibre Channel
cables that connect to
2 the master rack.
1

1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

Expansion

1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

Expansion

CXO7831A

Figure 80: 0C6D + 6D configuration—Fibre Channel loop 1B with expansion panels

Enterprise Virtual Array Hardware Configuration Guide 105

Expanding a Rack

Figure 81 shows the two 2A Fibre Channel loops and the expansion panels.
1 Expansion panel
2 5-meter Fibre Channel
cables that connect to
2 the master rack.
1

1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

Expansion

1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

Expansion

CXO7832A

Figure 81: 0C6D + 6D configuration—Fibre Channel loop 2A with expansion panels

106 Enterprise Virtual Array Hardware Configuration Guide

 Expanding a Rack

Figure 82 shows the two 2B Fibre Channel loops and the expansion panels.
1 Expansion panel
2 5-meter Fibre Channel
cables that connect to
the master rack.
2
1

1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

Expansion

1B 2B 1A 2A
IN OUT IN OUT IN OUT IN OUT

Expansion

CXO7833A

Figure 82: 0C6D + 6D configuration—Fibre Channel loop 2B with expansion panels

Enterprise Virtual Array Hardware Configuration Guide 107

Expanding a Rack

108 Enterprise Virtual Array Hardware Configuration Guide

Regulatory Notices and
Specifications
A
This appendix includes regulatory notices and product specifications for the HP StorageWorks
Enterprise Virtual Array.
The following topics are included:
■ Regulatory Notices, page 110
■ Fibre Channel Drive Enclosure Specifications, page 116
■ Fibre Channel Switch Specifications, page 120
■ Controller Specifications, page 121
■ Enterprise Rack, page 123

Enterprise Virtual Array Hardware Configuration Guide 109

Regulatory Notices and Specifications

Regulatory Notices

Federal Communications Commission Notice

Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has
established Radio Frequency (RF) emission limits to provide an interference-free radio
frequency spectrum. Many electronic devices, including computers, generate RF energy
incidental to their intended function and are, therefore, covered by these rules. These rules
place computers and related peripheral devices into two classes, A and B, depending upon
their intended installation. Class A devices are those that may reasonably be expected to be
installed in a business or commercial environment. Class B devices are those that may
reasonably be expected to be installed in a residential environment (for example, personal
computers). The FCC requires devices in both classes to bear a label indicating the
interference potential of the device as well as additional operating instructions for the user.
The rating label on the device shows the classification (A or B) of the equipment. Class B
devices have an FCC logo or FCC ID on the label. Class A devices do not have an FCC logo
or FCC ID on the label. After the Class of the device is determined, refer to the corresponding
statement in the following sections.

FCC Class A Certification

This equipment generates, uses, and may emit radio frequency energy. The equipment has
been type tested and found to comply with the limits for a Class A digital device pursuant to
Part 15 of the FCC rules, which are designed to provide reasonable protection against such
radio frequency interference.
Operation of this equipment in a residential area may cause interference, in which case the
user at the user’s own expense will be required to take whatever measures may be required to
correct the interference.
Any modifications to this device—unless approved by the manufacturer—can void the user’s
authority to operate this equipment under Part 15 of the FCC rules.

Note: Additional information on the need to interconnect the device with shielded (data) cables or
the need for special devices, such as ferrite beads on cables, is required if such means of
interference suppression was used in the qualification test for the device. This information will vary
from device to device and needs to be obtained from the HP EMC group.

Class A Equipment
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be required to correct the interference at
personal expense.

110 Enterprise Virtual Array Hardware Configuration Guide

 Regulatory Notices and Specifications

Class B Equipment
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit that is different from that to which the
receiver is connected.
■ Consult the dealer or an experienced radio or television technician for help.

Declaration of Conformity for Products Marked with the FCC Logo, United States Only
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
For questions regarding your product, refer to http://thenew.hp.com.
For questions regarding this FCC declaration, contact:
■ Hewlett-Packard Company
Product Regulations Manager
3000 Hanover St.
Palo Alto, CA 94304
■ Or call 1-650-857-1501
To identify this product, refer to the part, series, or model number found on the product.

Modifications
The FCC requires the user to be notified that any changes or modifications made to this device
that are not expressly approved by Hewlett-Packard Company may void the user's authority to
operate the equipment.

Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI
connector hoods in order to maintain compliance with FCC Rules and Regulations.

Laser Device
All Hewlett-Packard systems equipped with a laser device comply with safety standards,
including International Electrotechnical Commission (IEC) 825. With specific regard to the
laser, the equipment complies with laser product performance standards set by government
agencies as a Class 1 laser product. The product does not emit hazardous light; the beam is
totally enclosed during all modes of customer operation and maintenance.

Enterprise Virtual Array Hardware Configuration Guide 111

Regulatory Notices and Specifications

Laser Safety Warnings

Heed the following Warning:

WARNING: To reduce the risk of exposure to hazardous radiation:

■ Do not try to open the laser device enclosure. There are no user-serviceable
components inside.
■ Do not operate controls, make adjustments, or perform procedures to the laser device
other than those specified herein.
■ Allow only HP authorized service technicians to repair the laser device.

Compliance with CDRH Regulations

The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug
Administration implemented regulations for laser products on August 2, 1976. These
regulations apply to laser products manufactured from August 1, 1976. Compliance is
mandatory for products marketed in the United States.

Certification and Classification Information

This product contains a laser internal to the Optical Link Module (OLM) for connection to the
Fibre communications port.
In the USA, the OLM is certified as a Class 1 laser product conforming to the requirements
contained in the Department of Health and Human Services (DHHS) regulation 21 CFR,
Subchapter J. The certification is indicated by a label on the plastic OLM housing.
Outside the USA, the OLM is certified as a Class 1 laser product conforming to the
requirements contained in IEC 825-1:1993 and EN 60825-1:1994, including Amendment
11:1996.
The OLM includes the following certifications:
■ UL Recognized Component (USA)
■ CSA Certified Component (Canada)
■ TUV Certified Component (European Union)
■ CB Certificate (Worldwide)

Canadian Notice (Avis Canadien)

Class A Equipment
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.

112 Enterprise Virtual Array Hardware Configuration Guide

 Regulatory Notices and Specifications

Class B Equipment
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.

European Union Notice

Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the
Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the following European Norms (the
equivalent international standards are in parenthesis):
■ EN55022 (CISPR 22) - Electromagnetic Interference
■ EN55024 (IEC61000-4-2, 3, 4, 5, 6, 8, 11) - Electromagnetic Immunity
■ EN61000-3-2 (IEC61000-3-2) - Power Line Harmonics
■ EN61000-3-3 (IEC61000-3-3) - Power Line Flicker
■ EN60950 (IEC950) - Product Safety

Notice for France

DECLARATION D'INSTALLATION ET DE MISE EN EXPLOITATION d'un matériel de
traitement de l'information (ATI), classé A en fonction des niveaux de perturbations
radioélectriques émis, définis dans la norme européenne EN 55022 concernant la
Compatibilité Electromagnétique.

Germany Noise Declaration

Schalldruckpegel Lp = 70 dB(A)
Am Arbeitsplatz (operator position)
Normaler Betrieb (normal operation)
Nach ISO 7779:1999 (Typprüfung)

Enterprise Virtual Array Hardware Configuration Guide 113

Regulatory Notices and Specifications

Japanese Notice

Harmonics Conformance (Japan)

Taiwanese Notice

114 Enterprise Virtual Array Hardware Configuration Guide

 Regulatory Notices and Specifications

Country­Specific Certifications
HP tests electronic products for compliance with country-specific regulatory requirements, as
an individual item or as part of an assembly. The product label (see Figure 83) specifies the
regulations with which the product complies.

Note: Elements without an individual product certification label are qualified as part of the next
higher assembly (for example, enclosure, rack, or tower).

CXO8157A

Figure 83: Typical enclosure certification label

Note: The certification symbols on the label depend upon the certification level. For example, the
FCC Class A certification symbol is not the same as the FCC Class B certification symbol.

Enterprise Virtual Array Hardware Configuration Guide 115

Regulatory Notices and Specifications

Fibre Channel Drive Enclosure Specifications

This appendix defines the physical, environmental, and power specifications of the Fibre
Channel Drive Enclosure and the elements.

Physical Specifications
This section describes the physical specifications of the drive enclosure and elements.

WARNING: An assembled enclosure (all elements installed) weighs more than 29.5 kg (65
lb) and requires a minimum of two individuals to move.

Table 6 defines the dimensions and weights of the enclosure.

Table 6: Drive Enclosure Physical Specifications
Shipping
Empty Installed Carton Carton and Pallet

Note: Metric dimensions are expressed in whole numbers. For example, 10.795 cm is
expressed as 108 mm. Millimeter dimensions are always expressed in whole numbers.

Height 131 mm 131 mm 641 mm 768 mm

(5.16 in) (5.16 in) (25.25 in) (30.25 in)
Width 505 mm 505 mm 318 mm 610 mm
(19.875 in) (19.875 in) (12.5 in) (24 in)
Depth 448 mm 448 mm 597 mm 1016 mm
(17.625 in) (17.625 in) (23.5 in) (40 in)
Weight 10.9 kg 30.9 kg 43.6 kg 49 kg
(24 lb) (68 lb) (96 lb) (108 lb)

Table 7 defines the dimensions of the elements (that is, EMU, blowers, I/O module, drives, and
power supply).
Table 7: Drive Enclosure Elements Physical Specifications
Specification Installed Shipping Carton

Note: Metric dimensions are expressed in whole numbers. For example, 10.795 cm is
expressed as 108 mm. Millimeter dimensions are always expressed in whole numbers.

Environmental Monitoring Unit (EMU)

Height 114 mm (4.5 in) 210 mm (8.25 in)
Width 241 mm (9.5 in) 330 mm (13.5 in
Depth 35 mm (1.375 in) 108 mm (4.25 in)
Weight 0.6 kg (1.3 lb) 0.91 kg (2.0 lb)

116 Enterprise Virtual Array Hardware Configuration Guide

 Regulatory Notices and Specifications

Table 7: Drive Enclosure Elements Physical Specifications (Continued)

Specification Installed Shipping Carton

Note: Metric dimensions are expressed in whole numbers. For example, 10.795 cm is
expressed as 108 mm. Millimeter dimensions are always expressed in whole numbers.

Blower
Height 140 mm (5.5 in) 191 mm (7.5 in)
Width 159 mm (6.25 in) 203 mm (8.0 in)
Depth 83 mm (3.25 in) 229 mm (9.0 in)
Weight 0.45 kg (1.0 lb) 0.91 kg (2.0 lb)
I/O Module
Height 114 mm (4.5 in) 210 mm (8.25 in)
Width 41 mm (1.625 in) 108 mm (4.25 in)
Depth 241 mm (9.5 in) 330 mm (13.0 in)
Weight 0.59 kg (1.3 lb) 0.77 kg (1.7 lb)
Disk Drive
Height 114 mm (4.5 in) 216 mm (8.5 in)
Width 26 mm (1.025 in) 114 mm (4.5 in)
Depth 241 mm (9.5 in) 330 mm (13.0 in)
Weight 0.59 kg (1.3 lb) 1.0 kg (2.3 lb)
Power Supply (without blower)
Height 114 mm (4.5 in) 286 mm (11.25 in)
Width 159 mm (6.25 in) 330 mm (13.0 in)
Depth 241 mm (9.5 in) 419 mm (16.5 in)
Weight 1.82 kg (4.0 lb) 3.86 kg (8.5 lb)

Environmental Specifications
To ensure optimum product operation you must maintain the operational environmental
specifications listed in Table 8. The ambient temperature, that is the enclosure air intake or
room temperature, is especially critical.
Table 8: Environmental Operating Specifications
Ambient temperature: +10 °C to +35 °C (+50 °F to +95 °F) with an average rate of
change of 1 °C/hour maximum and a step change of 3 °C or less. Maintaining the
optimum ambient temperature within the specified range ensures that the internal
operating temperatures support the drive manufacturer’s MTBF specifications.
Relative humidity: 40% to 60% (noncondensing) with a step change of 10% or less
(noncondensing)
Air quality: Not to exceed a maximum of 500,000 particles, 0.5 micron or larger, per
cubic foot of air.
Heat dissipation: 1600 BTUs per hour

Enterprise Virtual Array Hardware Configuration Guide 117

Regulatory Notices and Specifications

When shipping, or placing this product in short term storage, HP recommends maintaining the
environmental conditions listed in Table 9.
Table 9: Environmental Shipping or Short-Term Storage Specifications
Ambient temperature: –40 °C to +66 °C (–40 °F to +151 °F)
Relative humidity: 10% to 80% noncondensing
Altitude: 15,240 m (50,000 ft)

Power Specifications
The input voltage to the drive enclosure power supplies is a function of the country-specific
input voltage to Enterprise storage system rack power distribution units (PDUs). Table 10
defines the AC input power available to the drive enclosure power supplies.

Caution: The AC power distribution within a rack ensures a balanced load to each PDU
and reduces the possibility of an overload condition. Changing the cabling to or from a
PDM could cause an overload condition.

Table 10: Enterprise Storage System AC Input Line Voltages

Specification Minimal Nominal Maximum
60 Hz Service
AC Line Frequency 57 Hz 60 Hz 63 Hz
AC Line Voltage–Japan 180 VAC 202 VAC 220 VAC
AC Line Voltage–North America 180 VAC 208 VAC 220 VAC
AC Line Voltage–Europe 208 VAC 240 VAC 254 VAC
50 Hz Service
AC Line Frequency 47 Hz 50 Hz 53 Hz
AC Line Voltage–Japan 180 VAC 202 VAC 220 VAC
AC Line Voltage–North America 190 VAC 220 VAC 235 VAC
AC Line Voltage–North America 200 VAC 230 VAC 244 VAC
AC Line Voltage–Europe 208 VAC 240 VAC 254 VAC

118 Enterprise Virtual Array Hardware Configuration Guide

 Regulatory Notices and Specifications

Table 11 defines the AC input current and wattage to the drive enclosure power supplies.
Table 11: AC Input Current and Wattage
Nominal Maximum
Input Voltage Amps Watts Amps Watts
60-Hz Input
100 VAC–JBOD 4.35 436 6.41 641
208 VAC–North America 2.03 419 2.94 609
50-Hz Input
120 VAC–JBOD 3.59 419 5.27 633
220 VAC–North America 1.92 418 2.78 608
230 VAC–North America 1.92 418 2.78 608
240 VAC–Europe 1.76 416 2.55 607

Table 12 and Table 13 define the output voltage and current specifications of the drive
enclosure power supply.
Table 12: Output Voltage and Current Specifications
Range
Specification Minimum Nominal Maximum
+5.1 VDC
Initial Voltage +5.13 VDC +5.18 VDC +5.23 VDC
Steady state current 1.0 A N/A 26.0 A
+12.2 VDC (Disk Drive Voltage)
Initial Voltage +12.13 VDC +12,25 VDC +12.37 VDC
Steady state current 1.0 A N/A 26.0 A
+12.5 VDC (Blower Voltage)
Initial Voltage +12.25 VDC +12.50 VDC +12.75 VDC
Steady state current 0.0 A N/A 2.0 A

Table 13: Dual Power Supply Configuration Power Specifications

Voltage Current (A) Power (W)
Maximum Continuous Current
+5.1 VDC (with a minimum +12.2 VDC load of 0A) 26.0 A 132 W
+12.2 VDC (with a minimum +5 VDC load of 4A) 28.0 A 342.0 W
+12.5 VDC 2.0 A 25.0 W
Total 499.0 W
Maximum Peak Current (Simultaneous Seek Activity)
+5.1 VDC 26.0 A 132.0 W
+12.2 VDC 43.0 A 524.0 W
+12.5 VDC 2.0 A 25.0 W
Total 681.0 W

Enterprise Virtual Array Hardware Configuration Guide 119

Regulatory Notices and Specifications

Fibre Channel Switch Specifications

The Fibre Channel Switch requires a clean, dry environment for normal operation. Table 14
lists the specifications for the Fibre Channel Switch.
Table 14: Fibre Channel Switch Specifications
Weight approximately 7.5 lbs.
Dimensions 8.50 x 1.57 x 16.00 inches (W x H x D)

Note: The switch with extender is 21.66 in (depth).

Operating Temperature 0 °C to 40 °C for normal operation (ambient air

temperature)
Storage Temperature -40 °C to 80 °C noncondensing
Power 50 or 60 Hz
100–250 VAC
0.5–0.3 A

120 Enterprise Virtual Array Hardware Configuration Guide

 Regulatory Notices and Specifications

Controller Specifications
This section defines the physical, power, and environmental specifications of the controller
enclosure.

Physical Specifications
Table 15 defines the dimensions of the controller and replaceable units.
Table 15: Controller Physical Specifications
Specification Installed Shipping

Note: Metric dimensions are expressed in whole numbers. For example, 10.795 cm is
expressed as 108 mm.

Controller Enclosure
Height 62 mm (2.45 in) 267 mm (10.5 in)
Width 502 mm (19.75 in) 762 mm (30 in)
Depth 444 mm (17.49 in) 762 mm (30 in)
Weight 10.4 kg (23 lb) 12.7 kg (28 lb)
Cache Battery Assembly
Height 57 mm (2.25 in) 108 mm (4.25 in)
Width 184 mm (7.25 in) 324 mm (12.75 in)
Depth 83 mm (3.25 in) 162 mm (6.375 in)
Weight 1.3 kg (2.8 lb) 1.5 kg (3.4 lb)
Blower
Height 55 mm (2.125 in) 165 mm (6.5 in)
Width 116 mm (4.625 in) 216 mm (8.5 in)
Depth 105 mm (4.125 in) 216 mm (8.5 in)
Weight 0.4 kg (0.8 lb) 0.92 kg (2 lb)

Power Specifications
Table 16 and Table 18 define the controller power supply input power requirements and output
power specifications.
Table 16: Controller Power Supply AC Power Requirements
AC Input Voltage Frequency
Minimum Nominal Maximum Minimum Nominal Maximum
180 VAC 202 VAC 220 VAC 47 Hz 50 Hz 53 Hz
208 VAC 57 Hz 60 Hz 63 Hz
208 VAC 240 VAC 254 VAC

Enterprise Virtual Array Hardware Configuration Guide 121

Regulatory Notices and Specifications

Table 17 defines the AC input current and wattage to the controller power supplies.
Table 17: AC Input Current and Wattage
Nominal Maximum
Input Voltage Amps Watts Amps Watts
60-Hz Input
100 VAC 0.928 94 1.53 150
120 VAC 0.788 94 1.25 148
208 VAC 0.576 97 0.73 146
50-Hz Input
220 VAC 0.616 102 0.69 146
240 VAC 0.573 100 0.64 147

Table 18 defines the output of the controller power supplies.

Table 18: Controller Power Supply Output Specifications
Voltage Specification Minimum Nominal Maximum
+3.3 VDC
Output Voltage 3.23 VDC 3.30 VDC 3.36 VDC
Steady state current 18 A1
Power 59.4W
+5.1 VDC
Output Voltage 4.80 VDC 5.00 VDC 5.25 VDC
Steady state current 5.0 A
Power 25.5 W
Total Current 24 A
Total Power 105.6 W
1. +3.3 VDC steady state current requires a minimum 5.0-V load of 1 A.
2. Total power includes 14.0 watts for the internal blower.

Environmental Specifications
There are no controller environmental specifications. See the “Environmental Specifications”
section in “Enterprise Rack” on page 124 for this information.

122 Enterprise Virtual Array Hardware Configuration Guide

 Regulatory Notices and Specifications

Enterprise Rack

Physical Specifications

WARNING: The weight of the drive enclosure with the elements installed
always requires at least two individuals to move. HP recommends using a fork
lift or a hand truck to move an enclosure in the shipping container.
CXO7196A

Table 19 through Table 22 defines the dimensions and weights of the Enterprise storage
system racks.
Table 19: Enterprise 42U Storage System Rack Physical Dimensions
Height Width Depth Max Wt
in / mm in / mm in / mm lbs / kg
Enterprise 2C6D 78.75 / 2000.0 23.7 / 602 35.8 / 909 918 / 416
Enterprise 2C12D 78.75 / 2000.0 23.7 / 602 35.8 / 909 1350 / 612
Enterprise 0C6D 78.75 / 2000.0 23.7 / 602 35.8 / 909 818 / 371
Enterprise 0C12D 78.75 / 2000.0 23.7 / 602 35.8 / 909 1250 / 567

Table 20: Enterprise 42U Storage System Rack Shipping Dimensions

Max Wt (with
Height Width Depth packaging)
in / mm in / mm in / mm lbs / kg
Enterprise 2C6D 85.38 / 2169 36.0 / 914 48.0 / 1220 1111 / 504
Enterprise 2C12D 85.38 / 2169 36.0 / 914 48.0 / 1220 1543 / 700
Enterprise 0C6D 85.38 / 2169 36.0 / 914 48.0 / 1220 1011 / 459
Enterprise 0C12D 85.38 / 2169 36.0 / 914 48.0 / 1220 1443 / 654

Table 21: Enterprise 41U Storage System Rack Physical Dimensions

Height Width Depth Max Wt
in / mm in / mm in / mm lbs / kg
Enterprise 2C6D 78.75 / 2000.0 23.7 / 602 39.1 / 993 917 / 416
Enterprise 2C12D 78.75 / 2000.0 23.7 / 602 39.1 / 993 1349 / 612
Enterprise 0C6D 78.75 / 2000.0 23.7 / 602 39.1 / 993 817 / 371
Enterprise 0C12D 78.75 / 2000.0 23.7 / 602 39.1 / 993 1249 / 567

Enterprise Virtual Array Hardware Configuration Guide 123

Regulatory Notices and Specifications

Table 22: Enterprise 41U Storage System Rack Shipping Dimensions

Max Wt (with
Height Width Depth packaging)
in / mm in / mm in / mm lbs / kg
Enterprise 2C6D 85.38 / 2169 36.0 / 914 48.0 / 1220 1110 / 503
Enterprise 2C12D 85.38 / 2169 36.0 / 914 48.0 / 1220 1542 / 699
Enterprise 0C6D 85.38 / 2169 36.0 / 914 48.0 / 1220 1010 / 458
Enterprise 0C12D 85.38 / 2169 36.0 / 914 48.0 / 1220 1442 / 654

Environmental Specifications
To ensure optimum product operation, you must maintain the operational environmental
specifications listed in Table 23. The ambient temperature (the enclosure air intake or room
temperature) is especially critical.
Table 23: Environmental Operating Specifications
.

Ambient temperature: +10 °C to +35 °C (+50 °F to +95 °F) with an average rate
of change of 1 °C/hour maximum and a step change of 3 °C or less.
Maintaining the optimum ambient temperature within the specified range ensures
that the internal operating temperatures support the drive manufacturer’s MTBF
specifications.
Relative humidity: 40% to 60% (noncondensing) with a step change of 10% or less
(noncondensing).
Air quality: Not to exceed a maximum of 500,000 particles, 0.5 micron or larger,
per cubic foot of air.
Heat dissipation: 12,708 BTUs per hour.

When shipping, or placing this product in short term storage, HP recommends maintaining the
environmental conditions listed in Table 24.
Table 24: Environmental Shipping or Short Term Storage Specifications
Ambient temperature: –40 °C to +66 °C (–40 °F to +151 °F)
Relative humidity: 10% to 80% (noncondensing)
Altitude: 15,240 m (50,000 ft)

124 Enterprise Virtual Array Hardware Configuration Guide

 Regulatory Notices and Specifications

Power Specifications
Table 25 defines the AC power specifications for the Enterprise storage system PDUs, PDMs,
drive enclosure power supplies, and controller enclosure power supplies.
Table 25: Enterprise Storage System AC Power Specifications
Nominal Input Voltage Specifications
60-Hz Service
202 VAC Japan
Voltage Range 180-220 VAC, 57-63Hz, 32 A, Single Phase
Power Receptacle 3-wire, 2-pole, IEC 309
208 VAC North America
Voltage Range 180-220 VAC, 57-63Hz, 30 A, Single Phase
Power Receptacle 3-wire, 2-pole, NEMA L6-30
240 VAC Europe
Voltage Range 208-254 VAC, 57-63 Hz, 32 A, Single Phase
Power Receptacle 3-wire, 2-pole, IEC 309
50-Hz Service
202 VAC Japan
Voltage Range 180-220 VAC, 47-63Hz, 32 A, Single Phase
Power Receptacle 3-wire, 2-pole, IEC 309
220 VAC North America
Voltage Range 190-235 VAC, 47-63Hz, 30 A, Single Phase
Power Receptacle 3-wire, 2-pole, NEMA L6-30
230 VAC North America
Voltage Range 200-244 VAC, 47-63Hz, 30 A, Single Phase
Power Receptacle 3-wire, 2-pole, NEMA L6-30
240 VAC Europe
Voltage Range 208-254 VAC, 57-63 Hz, 32 A, Single Phase
Power Receptacle 3-wire, 2-pole, IEC 309

The power consumption of an Enterprise storage system is 3,724 W.

Enterprise Virtual Array Hardware Configuration Guide 125

Regulatory Notices and Specifications

126 Enterprise Virtual Array Hardware Configuration Guide

 glossary

Glossary
This glossary defines terms used in this guide or related to this product and is not a
comprehensive glossary of computer terms.
Glossary
3U
A unit of measurement representing three “U” spaces. “U” spacing is used to designate panel or enclosure heights.
Three “U” spaces is equivalent to 5.25 inches (133 mm).
See also rack-mounting unit.
AL_PA
Arbitrated Loop Physical Address. A 1-byte value the arbitrated loop topology uses to identify the loop ports. This
value becomes the last byte of the address identifier for each public port on the loop.
ambient temperature
The air temperature in the area where a system is installed. Also, called intake temperature or room temperature.
ANSI
American National Standards Institute. A non-governmental organization that develops standards (such as SCSI
I/O interface standards and Fibre Channel interface standards) used voluntarily by many manufacturers within the
United States.
arbitrated loop
A Fibre Channel topology that links multiple ports (up to 126) together on a single shared simplex media.
Transmissions can only occur between a single pair of nodes at any given time. Arbitration is the scheme that
determines which node has control of the loop at any given moment.
arbitrated loop physical address
See AL_PA.
arbitrated loop topology
See arbitrated loop.
array
All the disk drives in a storage system that are known to and under the control of a controller pair.
bail lock
Part of the power supply AC receptacle that engages the AC power cord connector to ensure that the cord cannot
be accidentally disconnected.
baud
The maximum rate of signal state changes per second on a communication circuit. If each signal state change
corresponds to a code bit, then the baud rate and the bit rate are the same. It is also possible for signal state changes
to correspond to more than one code bit so the baud rate may be lower than the code bit rate.

Enterprise Virtual Array Hardware Configuration Guide 127

Glossary

bay
The physical location of an element, such as a drive, I/O module, EMU or power supply in a drive enclosure. Each
bay is numbered to define its location.
cabinet
An alternate term used for a rack.
cable assembly
A fiber optic cable that has connectors installed on one or both ends. General use of these cable assemblies
includes the interconnection of multimode fiber optic cable assemblies with either LC or SC type connectors.
■ When there is a connector on only one end of the cable, the cable assembly is referred to as a pigtail.
■ When there is a connector on both ends of the cable, the cable assembly is referred to as a jumper.
client
A software program that uses the services of another software program. The Command View EVA client is a
standard internet browser.
controller
A hardware/firmware device that manages communications between host systems and other devices. Controllers
typically differ by the type of interface to the host and provide functions beyond those the devices support.
controller enclosure
A unit that holds one or more controllers, power supplies, blowers, cache batteries, transceivers, and connectors.
controller pair
Two interconnected controller modules which together control a disk array. A controller pair and the disk array
together constitute a storage system.
CRU
Customer Replaceable Unit. A storage system element that a user can replace without using special tools or
techniques, or special training.
customer replaceable unit
See CRU.
device ports
Controller pair device ports connected to the storage system’s disk drive array through the FC-AL. Also called a
device-side port.
device-side ports
See device ports.
disk drive blank
A carrier that replaces a disk drive to control airflow within a drive enclosure whenever there is less than a full
complement of storage devices.
disk drive
A carrier-mounted storage device supporting random access to fixed size blocks of data.
disk drive
A disk drive mounted in a drive enclosure that communicates with a controller pair through the device-side Fibre
Channel loops. A disk drive is hardware with embedded software, as opposed to a virtual disk, which is
constructed by the controllers. Only the controllers can communicate directly with the disks drives
The disk drives, in aggregate, are called the array and constitute the storage pool from which the controllers create
virtual disks.

128 Enterprise Virtual Array Hardware Configuration Guide

 Glossary

drive blank
See disk drive blank.
drive enclosure
A unit that holds storage system devices such as disk drives, power supplies, fans, I/O modules, transceivers or
EMUs.
dual power supply configuration
See redundant power configuration.
dual-loop
A configuration where each drive is connected to a pair of controllers through two loops. These two Fibre Channel
loops constitute a loop pair.
EIA
Electronic Industries Alliance. A standards organization specializing in the electrical and functional characteristics
of interface equipment.
electromagnetic interference
See EMI.
electrostatic discharge
See ESD.
element
1. In a drive enclosure, a device such as an EMU, power supply, disk, fan, or I/O module. The object can be
controlled, interrogated, or described by the enclosure services process.
2. In the HP Open SAN Manager, a controllable object, such as the HP StorageWorks Enterprise Storage System.
EMI
Electromagnetic Interference. The impairment of a signal by an electromagnetic disturbance.
EMU
Environmental Monitoring Unit. An element which monitors the status of an enclosure, including the power, air
temperature, and fan status. The EMU detects problems and displays and reports these conditions to a user and the
controller. In some cases, the EMU implements corrective action.
enclosure
A unit used to hold various storage system devices such as disk drives, controllers, power supplies, fans, an EMU,
or I/O modules.
enclosure address bus
An Enterprise Storage System bus that interconnects and identifies controller enclosures and drive enclosures by
their physical location. Enclosures within a reporting group can exchange environmental data. This bus uses
junction boxes and cables to assign enclosure numbers to each enclosure. Communications over this bus do not
involve the FC-AL bus and are, therefore, classified as out-of-band communications.
Enclosure Services Interface
See ESI.
Enclosure Services Processor
See ESP.

Enterprise Virtual Array Hardware Configuration Guide 129

Glossary

Enterprise Virtual Array rack

A unit that holds controller enclosures, drive enclosures, power distribution supplies, and enclosure address buses
that comprise an Enterprise Storage System solution. Also, called the Enterprise Storage System rack.
See also rack.
Enterprise Virtual Array
The Enterprise Virtual Array is a product that consists of one or more storage systems. Each storage system
consists of a pair of controllers and the disk drives they manage. A storage system within the Enterprise Virtual
Array can be formally referred to as an Enterprise Storage System, or generically referred to as the storage system.
environmental monitoring unit
See EMU.
ESD
Electrostatic Discharge. The emission of a potentially harmful static electric voltage as a result of improper
grounding.
ESI
Enclosure Services Interface. The SCSI-3 engineering services interface implementation developed for HP
StorageWorks products. A bus that connects the EMU to the drives.
ESP
Enclosure Services Processor. An EMU that implements an enclosure’s services process.
fabric
A Fibre Channel fabric switch or two or more interconnected Fibre Channel switches allowing data transmission.
fabric port
A port which is capable of supporting an attached arbitrated loop. This port on a loop will have the AL_PA
hexadecimal address 00 (loop ID 7E), giving the fabric the highest priority access to the loop. A loop port is the
gateway to the fabric for the node ports on a loop.
fan
The variable speed airflow device that cools an enclosure or element by forcing ambient air into an enclosure or
element and forcing heated air out the other side.
FC HBA
Fibre Channel Host Bus Adapter. An interchangeable term for Fibre Channel adapter.
See also FCA.
FCA
Fibre Channel Adapter. An adapter used to connect the host server to the fabric. Also, called a Host Bus Adapter
(HBA) or a Fibre Channel Host Bus Adapter (FC HBA).
See also FC HBA.
FC-AL
Fibre Channel Arbitrated Loop. The American National Standards Institute’s (ANSI) document which specifies
arbitrated loop topology operation.
FCC
Federal Communications Commission. The federal agency responsible for establishing standards and approving
electronic devices within the United States.
FCP
Fibre Channel Protocol. The mapping of SCSI-3 operations to Fibre Channel.

130 Enterprise Virtual Array Hardware Configuration Guide

 Glossary

fiber optic cable

A transmission medium designed to transmit digital signals in the form of pulses of light. Fiber optic cable is noted
for its properties of electrical isolation and resistance to electrostatic contamination.
fiber optics
The technology where light is transmitted through glass or plastic (optical) threads (fibers) for data communication
or signaling purposes.
fiber
The optical media used to implement Fibre Channel.
Fibre Channel adapter
See FCA.
Fibre Channel
A data transfer architecture designed for mass storage devices and other peripheral devices that require very high
bandwidth.
Fibre
The international spelling that refers to the Fibre Channel standards for optical media.
field replaceable unit
See FRU.
frequency
The number of cycles that occur in one second expressed in Hertz (Hz). Thus, 1 Hz is equivalent to one cycle per
second.
FRU
Field Replaceable Unit. A hardware element that can be replaced in the field. This type of replacement can require
special training, tools, or techniques. Therefore, FRU procedures are usually performed only by an authorized
service representative.
Gb
Gigabit. A measurement of the rate at which the transfer of bits of data occurs. Sometimes referred to as Gbps.
Nominally, a Gb is a transfer rate of 1,000,000,000 (109) bits per second.
For Fibre Channel transceivers or FC loops the Gb transfer rates are:
■ 1 Gb is a transmission rate of 1,062,500,000 bits per second.
■ 2 Gb is a transmission rate of 2,125,000,000 bits per second.
GB
Gigabyte. A unit of measurement defining either:
■ A data transfer rate.
See also GBps.
■ A storage or memory capacity of 1,073,741,824 (230) bytes.
GBIC
Gigabit Interface Converter.
See transceiver.
Gbps
Gigabit per second. A measurement of the rate at which the transfer of bits of data occurs. Nominally, a Gb is a
transfer rate of 1,000,000,000 (109) bits per second.
See also Gb.

Enterprise Virtual Array Hardware Configuration Guide 131

Glossary

GBps
Gigabytes per second. A measurement of the rate at which the transfer of bytes of data occurs. A GBps is a transfer
rate of 1,000,000,000 (109) bytes per second.
See also GB.
Giga (G)
The notation to represent 109 or 1 billion (1,000,000,000).
gigabaud
An encoded bit transmission rate of one billion (109) bits per second.
gigabit per second
See Gbps.
gigabit
See Gb.
graphical user interface
See GUI.
GUI
Graphical User Interface. Software that displays the status of a storage system and allows its user to control the
storage system.
HBA
Host Bus Adapter.
See FCA.
Host Bus Adapter
See FCA.
host computer
See host.
host ports
A connection point to one or more hosts through a Fibre Channel fabric. A host is a computer that runs user
applications and that uses (or can potentially use) one or more of the virtual disks that are created and presented by
the controller pair.
host
A computer that runs user applications and uses (or can potentially use) one or more virtual disks created and
presented by the controller pair.
host-side ports
See host ports.
hot-pluggable
A method of element replacement whereby the complete system remains operational during element removal or
insertion. Replacement does not interrupt data transfers to other elements.
HP OpenView Storage Management Appliance software
A centralized, appliance-based monitoring and management interface that supports multiple applications,
operating systems, hardware platforms, storage systems, tape libraries and SAN-related interconnect devices. It is
included and resides on the HP OpenView Storage Management Appliance, a single aggregation point for data
management.

132 Enterprise Virtual Array Hardware Configuration Guide

 Glossary

HP StorageWorks Command View EVA

The graphical user interface (GUI) through which a user can control and monitor a storage system. The Command
View EVA software can be installed on more than one management appliance in a fabric. Each installation of the
Command View EVA software is a management agent. The client for the agent is a standard browser.
HP StorageWorks
The HP trademarked name used to describe the set of rack-mounted enclosures containing controllers, transceivers,
I/O modules, EMUs, disk drives, cables, blowers, and power supplies used to design and configure a
solution-specific storage system.
hub
A communications infrastructure device to which nodes on a multi-point bus or loop are physically connected. It is
used to improve the manageability of cables.
I/O module
Input/Output module. The enclosure element that is the FC-AL interface to the host or controller. I/O modules are
bus speed specific; either 1 Gb or 2 Gb.
in-band communication
The method of communication between the EMU and controller that utilizes the FC-AL bus.
See also out-of-band communication.
input/output module
See I/O module.
intake temperature
See ambient temperature.
interface
A set of protocols used between components such as cables, connectors, and signal levels.
JBOD
Just a Bunch of Disks. A number of disks connected to one or more controllers.
just a bunch of disks
See JBOD.
KB
Kilobyte. A unit of measurement defining either storage or memory capacity.
1. For storage, a KB is a capacity of 1,000 (103) bytes of data.
2. For memory, a KB is a capacity of 1,024 (210) bytes of data.
K
Kilo. A scientific notation denoting a multiplier of one thousand (1,000).
laser
A device that amplifies light waves and concentrates them in a narrow, very intense beam.
LCD
Liquid Crystal Display. The indicator on a panel that is associated with an element. The LCD is usually located on
the front of an element.
LED
Light Emitting Diode. A semiconductor diode, used in an electronic display, that emits light when a voltage is
applied to it.

Enterprise Virtual Array Hardware Configuration Guide 133

Glossary

light emitting diode

See LED.
link
A connection between ports on Fibre Channel devices. The link is a full duplex connection to a fabric or a simplex
connection between loop devices.
loop ID
Seven-bit values numbered contiguously from 0 to 126 decimal and represent the 127 valid AL_PA values on a
loop (not all 256 hexadecimal values are allowed as AL_PA values per FC–AL).
loop pair
A Fibre Channel attachment between a controller and disk drives. Disk drives connect to controllers through paired
Fibre Channel arbitrated loops. There are two loop pairs, designated loop pair 1 and loop pair 2. Each loop pair
consists of two loops (called loop A and loop B) that operate independently during normal operation, but provide
mutual backup in case one loop fails.
loop switch
A unit that acts as a central point of interconnection and establishes a fault-tolerant physical loop topology.
loop
See arbitrated loop.
management agent
The Command View EVA software that controls and monitors the Enterprise storage system. The software can
exist on more than one management appliance in a fabric. Each installation of the Command View EVA software
is a management agent.
MB
Megabtye. A term defining either:
■ A data transfer rate.
See also MBps.
■ A measure of either storage or memory capacity of 1,048,576 (220) bytes.
Mb
Megabit. A term defining a data transfer rate.
See also Mbps.
Mbps
Megabits per second. A measure of bandwidth or data transfers occurring at a rate of 1,000,000 (106) bits per
second.
MBps
Megabytes per second. A measure of bandwidth or data transfers occurring at a rate of 1,000,000 (106) bytes per
second.
Mega
A notation denoting a multiplier of 1 million (1,000,000).
Network Storage Controller
See NSC.
node port
A device port that can operate on the arbitrated loop topology.

134 Enterprise Virtual Array Hardware Configuration Guide

 Glossary

NSC
Network Storage Controller. The controllers used by the Enterprise Storage System.
OCP
Operator Control Panel. The element that displays the controller’s status using LEDs and an LCD. Information
selection and data entry is controlled by the OCP pushbuttons.
operator control panel
See OCP.
out-of-band communication
Communication between an enclosure and reporting group elements that does not use the FC-AL bus, such as the
enclosure address bus.
See also in-band communication.
parity
A method of checking if binary numbers or characters are correct by counting the ONE bits. In odd parity, the total
number of ONE bits must be odd; in even parity, the total number of ONE bits must be even. Parity information
can be used to correct corrupted data.
PDM
Power Distribution Module. A thermal circuit breaker equipped power strip that distribute power from a PDU to
Enterprise Storage System elements.
PDU
Power Distribution Unit. The rack device that distributes conditioned AC or DC power within a rack.
port
A Fibre Channel connector on a Fibre Channel device.
power distribution module
See PDM.
power distribution unit
See PDU.
power supply
An element that develops DC voltages for operating the storage system elements from either an AC or DC source.
rack
A floor-standing structure primarily designed for, and capable of, holding and supporting storage system
equipment. All racks provide for the mounting of panels per Electronic Industries Alliance (EIA) Standard
RS-310-C.
rack-mounting unit
A measurement for rack heights based upon a repeating hole pattern. It is expressed as “U” spacing or panel
heights. Repeating hole patterns are spaced every 1.75 inches (44.45 mm) and based on EIA’s Standard RS-310-C.
For example, a 3U unit is 5.25-inches (133.35 mm) high and a 4U unit is 7.0-inches (177.79 mm) high.
redundancy
1. Element Redundancy—The degree to which logical or physical elements are protected by having another
element that can take over in case of failure. For example, each loop of a device-side loop pair normally work
independently but can take over for the other in case of failure.
2. Data Redundancy—The level to which user data is protected. Redundancy is directly proportional to cost in
terms of storage usage; the greater the level of data protection, the more storage space is required.

Enterprise Virtual Array Hardware Configuration Guide 135

Glossary

redundant power configuration

A capability of the Enterprise Storage System racks and enclosures to allow continuous system operation by
preventing single points of power failure.
■ For a rack, two AC power sources and two power conditioning units distribute primary and redundant AC
power to enclosure power supplies.
■ For a controller or drive enclosure, two power supplies ensure that the DC power is available even when there
is a failure of one supply, one AC source, or one power conditioning unit. Implementing the redundant power
configuration provides protection against the loss or corruption of data.
room temperature
See ambient temperature.
SCSI
1. Small Computer System Interface. An American National Standards Institute (ANSI) interface that defines the
physical and electrical parameters of a parallel I/O bus used to connect computers and a maximum of 16 bus
elements.
2. The communication protocol used between a controller pair and the hosts. Specifically, the protocol is FC-AL
or SCSI on a Fibre Channel. SCSI is the higher command-level protocol and Fibre Channel is the low-level
transmission protocol. The controllers have full support for SCSI-2; additionally, they support some elements
of SCSI-3.
SCSI-3 Enclosure Services
See SES.
SCSI-3
The ANSI standard that defines the operation and function of Fibre Channel systems.
SES
SCSI-3 Enclosures Services. Those services that establish the mechanical environment, electrical environment,
and external indicators and controls for the proper operation and maintenance of devices within an enclosure.
small computer system interface
See SCSI.
solutions rack
A rack containing controller enclosures, drive enclosures, power distribution, enclosure address buses, and so forth
that provide a specific solution such as the Enterprise storage system rack.
See also rack.
storage system
The controllers, storage devices, enclosures, cables, and power supplies and their software.
switch
An electromechanical device that initiates an action or completes a circuit.
TBps
Terabytes per second. A data transfer rate of 1,000,000,000,000 (1012) bytes per second.
TB
Terabyte. A term defining either:
■ A data transfer rate.
See also TBps.
■ A measure of either storage or memory capacity of 1,099,5111,627,776 (240) bytes.

136 Enterprise Virtual Array Hardware Configuration Guide

 Glossary

terminator
Interconnected elements that form the ends of the transmission lines in the enclosure address bus.
topology
An interconnection scheme that allows multiple Fibre Channel ports to communicate. Point-to-point, arbitrated
loop, and switched fabric are all Fibre Channel topologies.
transceiver
The device that converts electrical signals to optical signals at the point where the fiber cables connect to the FC
elements such as hubs, controllers, or adapters. Also called a Gigabit Interface Converter (GBIC).
units
See rack-mounting units.

Enterprise Virtual Array Hardware Configuration Guide 137

Glossary

138 Enterprise Virtual Array Hardware Configuration Guide

 index

0C12D configuration enclosure address bus 51

describing features 22 Fibre Channel loops 52
using 73
0C6D + 6D configuration A
describing features 99 AC power
enclosure address bus 99 specifications 122
Fibre Channel loops 99 AC power specifications 119
0C6D configuration addition, FC loop switch 85
describing features 21 addressing enclosures 63
expanding 99 air quality
2 x 2C12D + 0C12D configuration environmental specifications 117
describing features 73 operating specifications 124
enclosure address bus 73 altitude
Fibre Channel loops 74 shipping 118, 124
2C12D + 0C6D configuration short term storage 118
describing features 63 ambient temperature
enclosure address bus 63 environmental specifications 117
Fibre Channel loops 64 operating 124
2C12D configuration shipping 118, 124
cable management 40 short term storage 118, 124
describing features 18 array expansion 73
enclosure address bus 30 ASCII configuration 51
expanding 63, 73 audience 10
Fibre Channel loops 31 authorized reseller, HP 14
2C6D + 6D configuration
describing features 89 B
enclosure address bus 89 blowers, physical specifications 117
Fibre Channel loops 90 BTU specifications 117, 124
2C6D configuration
cable management 50 C
describing features 17, 41, 88
cable containment spools 39, 40
enclosure address bus 41
cable management 39, 50, 56
expanding 89
cable management arms 39
Fibre Channel loops 42
cable reconfiguration 85
41U rack 16
cables
42U rack 16
FCC compliance statement 111
8C8D configuration
CDRH, compliance regulations 112
cable management 56
Center for Devices and Radiological Health. See
describing features 19, 51
CDRH

Enterprise Virtual Array Hardware Configuration Guide 139

Index

certification product labels 115 short term storage 124

Class A equipment, Canadian compliance statement equipment symbols 12
112 expansion
Class B equipment, Canadian compliance statement connecting Fibre Channel cables 74
113 expandable configurations 18, 19
Command View EVA 25 expansion rack 21, 22
configurations, expansion 73 expansion configurations 21
controllers expansion panels
describing features 25 removing 85
physical dimensions 121 using 31
power requirements 121 expansion panels, usage of
conventions 0C6D + 6D configuration 104
document 11 2 x 2C12D + 0C12D configuration 79
equipment symbols 12 2C12D + 0C6D configuration 69
text symbols 11 2C12D configuration 36
country-specific certifications 115 2C6D + 6D configuration 95
2C6D configuration 46
D expansion racks 22, 63, 73, 74
DC power specifications 119, 122
disk drives, MTBF specifications 117, 124 F
document FC drive enclosures
conventions 11 adding 88
prerequisites 10 describing features 24
related documentation 10 FC loop switches
drive enclosures, adding 88 adding 85
dual power supplies, controller 25 describing features 26
dual-rack configuration 63 environmental specifications 120
using 31
E FCC
enclosure address bus configurations Class A Equipment, compliance notice 110
2 x 2C12D + 0C12D configuration 73 Class B Equipment, compliance notice 111
2C12D + 0C6D configuration 63 Declaration of Conformity 111
2C12D configuration 30 modifications 111
2C6D configuration 41 notice 110
8C8D configuration 51 FCC Class A certification 110
enclosure address bus terminator 30, 89 Federal Communications Commission (FCC) notice
enclosure address bus, expanding 63, 73 110
enclosure address bus, polarity 63, 73 Federal Communications Commission. See FCC
enclosure certification label 115 Fibre Channel cable management 39, 50, 56
enclosures, physical specifications 116 Fibre Channel cables
environmental specifications connecting 31
air quality 117, 124 reconfiguring 85
altitude 118 Fibre Channel drive enclosure 24
ambient temperature Fibre Channel loop configurations 31
operating specifications 124 flumes 39, 40
shipping 124 fork lift, using 123
short term storage 124
controllers 122 G
drive enclosure 117 getting help 14
Fibre Channel loop switches 120 graphite rack 16
heat dissipation 124
relative humidity 117, 118, 124 H
shipping 118, 124 hand truck, using 123

140 Enterprise Virtual Array Hardware Configuration Guide

 Index

help, obtaining 14 loop switches, environmental specifications for 120

HP loop topology 26
authorized reseller 14
storage website 14 M
technical support 14 master racks 63, 74
moving enclosure WARNING 123
I MTBF 117, 124
increasing storage capacity 22, 23
intake temperature See ambient temperature O
opal rack 16
J
junction boxes 30 P
physical specifications
L blowers 117
labels enclosures 116
enclosure certification 115 power specifications
product certification 115 AC 119, 122
laser device controller 121
regulatory compliance notice 111 DC 119, 122
lasers drive enclosure 118
radiation, warning 112 prerequisites 10
loop 1A product certification 115
0C6D + 6D configuration 100, 104
2 x 2C12D + 0C12D configuration 75, 79 R
2C12D + 0C6D configuration 65, 69 rack
2C12D configuration 32, 36 environmental specifications 124
2C6D + 6D configuration 90, 95 power specifications 125
2C6D configuration 42, 46 rack additions, drive enclosures 88
8C8D configuration 52 rack expansion 18, 19, 21
loop 1B rack stability, warning 13
0C6D + 6D configuration 101, 105 rack upgrades, FC loop switches 85
2 x 2C12D + 0C12D configuration 76, 80 radial clips 39
2C12D + 0C6D configuration 66, 70 reconfiguration, cables 85
2C12D configuration 33, 37 regulatory compliance notices
2C6D + 6D configuration 92, 96 cables 111
2C6D configuration 43, 47 Class A 110
8C8D configuration 53 Class B 111
loop 2A European Union 113
0C6D + 6D configuration 102, 106 Japan 114
2 x 2C12D + 0C12D configuration 77, 81 laser devices 111
2C12D + 0C6D configuration 67, 71 modifications 111
2C12D configuration 34, 38 Taiwan 114
2C6D + 6D configuration 93, 97 regulatory notices 110
2C6D configuration 44 related documentation 10
8C8D configuration 54 relative humidity
loop 2B drive enclosure 117, 118
0C6D + 6D configuration 103, 107 operating 124
2 x 2C12D + 0C12D configuration 78, 82 shipping 118, 124
2C12D + 0C6D configuration 68, 72 short term storage 118, 124
2C12D configuration 35, 39 room temperature See ambient temperature
2C6D + 6D configuration 94, 98
2C6D configuration 45, 49 S
8C8D configuration 55 SFP 26

Enterprise Virtual Array Hardware Configuration Guide 141

Index

shipping container, moving 123 triple-rack configuration 73

shipping specifications 118, 124 two-rack configuration 63
short term storage specifications 124
specifications U
disk drive, MTBF 117, 124 upgrading version 83
enclosure 121 using fork lifts 123
environmental 124 using hand trucks 123
heat dissipation 117
operating 124 V
physical 116, 121 version comparison 83
power 118, 121 version upgrade 83
shipping 124
short term storage 124 W
spools 40
warning
storage racks 16
rack stability 13
switches 31
symbols on equipment 12
symbols in text 11
warnings
symbols on equipment 12
lasers, radiation 112
system expansion 21, 22, 73
WARNINGs, enclosure moving 123
websites
T
HP storage 14
technical support, HP 14 wire looms 39
terminator 30, 41, 89
text symbols 11 Y
topology 26
Y cables 30, 41
transceivers 26

142 Enterprise Virtual Array Hardware Configuration Guide