All sealing Product via JINWOO KOREA

[email protected]

One Source for Sealing Solution Provider to

every of your Specific Application

JINWOO KOREA
 JINWOO KOREA
RUBBER
J#RNR Natural Rubber (NR)
Workable Temperature (dry heat) Primary Uses
low high O-ring, Rubber seals
-40 60 Low pressure hydraulic seals.
-104 140
Application Advantage Appilcation Disadvantage
excellent compression set poor weather resistance
good resilience & abrasion moderate heat resitance
good surface friction properties
high tear strength
low crack growth
good low temperature properties

Lorem ipsum
J#RNB Nitrile Rubber (NBR, BUNA-N)
Workable Temperature (dry heat) Primary Uses
low high Gaskets, O-ring, Oil seal lips
-25 100 Low pressure hydraulic seals.
-77 212
Application Advantage Application Disadvantage
excellent compression set poor weather resistance
good tear resistance moderate heat resitance
good abrasion resistance not suited for using in highly
good petroleum-based oils resistance polar solvents
good mineral oil based hydraulic fluids
resistance
good solvent, water and alcohols resistance

J#RNEO NEOPRENE (Chloroprene, CR)

Workable Temperature (dry heat) Primary Uses
low high Gaskets, O-ring, Rubber seals
-30 100 Hose and wire
-86 212
Application Advantage Application Disadvantage
high resilience with low compression set moderate water resistance
moderate resistance to petroleum oils not effective in solvents environments
good resistance to ozone, UV, oxygen
excellence resitance to Freon and
ammnonia

J#REP EPDM (Ethylene Prophylene)

Workable Temperature (dry heat) Primary Uses
low high O-rings, Flanges seals and gaskets
-40 120 Water system seal
-104 248 General industrial use
Application Advantage Hydraulic or rotary seal
Automotive weather-stripping and seals Electrical insulation
exceptionally good weather aging and
ozone resistance Application
Application
Disadvantage
Disadvantage
exellent water and chemical resistance poor petroleum
poor petroleum
oil and sovent
oil and
resistance
sovent resistance
good in ketones and alcohols not recommended
not recommended for food applications
for food applications
good heat resistance not recommended
not recommended for exposure
for exposure to to
good low temparature flexibility aromatic hydrocarbons
aromatic hydrocarbons
 JINWOO KOREA

J#RSB SBR (Styrene butadiene)

Workable Temperature (dry heat) Primary Uses
low high O-ring, Rubber seals
-35 90
-95 194
Appilcation Advantage Appilcation Disadvantage
good resistance to water poor weather resistance
low cost non-oil resistance material poor petroleum oil and solvent resistance

J#RVT Viton (Fluoroelastomer, FPM/FKM)

Workable Temperature (dry heat) Primary Uses
low high o-rings, automotive fuel handling
-25 220 aircraft engine seals
-77 428 high temperature applications
Application Advantage requiring good compression set
excellent chemical resistance performance
excellent heat resistance Application Disadvantage
good mechanical properties poor low temperature flexibility
good compression set resistance poor resistance to hot water and steam
resistance to wide range of oils and not recommended for exposure to
solvents hot water, steam polar solvents

J#RPEP EPDM with P.T.F.E Serration (Ebilon)

EPDM with P.T.F.E serration gasket

Developed in placed of P.T.F.E soft-sheet and added serration to the friction surface
of product. This can be available for enough pressure.
EPDM PTFE flange gasket has EPDM's advantage and also PTFE's advantage.
Gasket has two sealing rings a primary and secondary
Almost universal chemical resistance and non-contaminating for ultra-pure
applications, along with the EPDM memory giving a long sealing life.

Workable Temperature (dry heat) Primary Uses

low high It is used in all chemicals solutions
-40 150 oils, gas, chemical product concerned
-104 302 about fluid pollution, and especially
a b P.T.F.E COATING
d2 n- e
chemical carriers much.
d1
Low bolt torque required seal
m
D1
PCD D2
D3

Application Advantage Application Disadvantage

exellent chemical resistance not recommended for exposure to
in most cases molten alkali metals, fluorine gas,
hydrogen fluoride, aromatic
hydrocarbons.

2 2 / 3
STEEL RUBBER

J#SRG-01 Material
Ro(Ω) Ro(Ω) (Ω) (Ω) Test Ud(KV) Ud(KV)
1 5 1 5 voltage(V) 1 5
EPDM nb

> >
FPM-S > >15
For various applications
nb=without results

J#SRG-02

Gasket parameters
due to DIN 28 090-1

J#SRG J#SRG
J#SRG-05
01,03,04,07 01,03,04,07
In special dimensions,
"NBR, CR
NR, EPDM
materials
J#SRG-03 IIR, CSM
FPM-S"

face roughness Ra
surface pressure 15 m
limits for 450 y
surface pressure (15)
limits for 50 (435)
For various applications, top choice
for joints connecting non-metallic

J#SRG-04
CSM =Chlorosulfonated Polyethylene Rubber
Materials
Temp. (Min. to Max.) : -20 ~ +120 (-4 ~ +248˚F)
Good Resistance to Chemicals, Weather, Ozone,
NR = Natural Rubber
Oxygen, Water, Oils, Alkalis and Acids
Temp. (Min. to Max.) : -40 ~ +60 (-40 ~ +140˚F)
Poor Resistance to Aldehyde, Amine, Ester,
Good Resistance to Alcohol, Water
Halogenated Solvent, Hydrocarbon
Poor Resistance to Acids, Ozone, Sunlight, Oils,
pairs of plastic stub ends
Fuels, Solvents
J#SRG-05 EPDM = Eth ylene Propylene Diene Monomer
Temp. (Min. to Max.) : -40 ~ +140 (-40 ~ +284˚F)
NBR = Nitrile Butadiene Rubber
Good Resistance to Ozone, Oxygen, Acids, Alkalis,
Temp. (Min. to Max.) : -25 ~ +140 (-13 ~ +284˚F)
Ketones, Heat and Aging
Good Resistance to Chemicals, Oils, Lubricants,
Poor Resistance to Diester Oils, Fuels
Fuels, Alcohol
Poor Resistance to Chlorinated Solvent, Alkalis,
For various applications, top choice
Ozone, Hydrocarbon
FPM ( Viton) = Fluoroelastomer
and heavy duty services Temp. (Min. to Max.) : -25 ~ +220 (-13 ~ +428˚F)
Excellent Resistance to Oils, Chlorinated Solvent, Fuels,
J#SRG-06 HNBR = Hydr ated Nitrile Butadiene Rubber
Lubricants, Hydrocarbon
Temp. (Min. to Max.) : -40 ~ +150 (-40 ~ +302˚F)
Poor Resistance to Ketone, Alkalis, Aldehyde, Ether,
Good Resistance to Oils, Sour Gas, Hot Water/
Ammonia Refrigerant
Steam, Ozone and Environmental Aging
Poor Resistance to Hydrocarbon, Ester, Ether,
Halogenated Solvents, Ketone
IIR = Isobut ylene Isoprene Rubber
Temp. (Min. to Max.) : -40 ~ +120 (-40 ~ +248˚F)
First Safe pipelines
Good Resistance to Acids, Alkalis, Electricity, Heat,
CR = Chlor oprene Rubber (Neoprene)
Environmental Aging
J#SRG-07 Temp. (Min. to Max.) : -25 ~ +95 (-13 ~ +203˚F)
Poor Resistance to Fuels, Oils, Solvents, Hydrocarbons
Good Resistance to Chemical, Water, Lubricants,
Weather
Poor Resistance to Oils, Fuels, Hydrocarbon,
Steel Insert
Chlorinated Solvent, Ketone
Standard : Carbon Steel
Optional : Stainless Steel
Flexible design gasket with
visible stainless steel insert
* Also Available as "HP" (High Purity)
 JINWOO KOREA

J#SRS-01 Features
High level of security against slippage or blow out provided by the steel reinforcement.
Simple, secure and cost-effective installation due to its stability, compared to non-
d2 reinforced rubber gaskets.
d2 Exceptionally low leakage rate due to the homogeneous rubber casing, making it
particularly suitable for pipeline systems carrying media harmful to the environment.
Low demand on the flange surface due to the soft, flexible sealing surface, seals

s
can even be created with slightly damaged flanges.

Gas and water supply

Chemical industries where aggressive and environmentally harmful media are used
Flue gas cleaning systems and power plant cooling circuits
Wastewater systems
Pipeline construction with vacuum-operated pipelines
Pipeline systems with all-rubber flange sealing surfaces
With enamel pipelines and apparatus flanges.

J#SRS-02
Features
Leak-proof even at the lowest tightening torques, making the rubber-steel gasket
d2 profile C#NSRS-02 particularly suitable for plastic flange connections where there
no high forces can be exerted.
d2
Highly leak-proof due to the self-sealing effect of the sealing lips under internal
pressure; the internal pressure forces the sealing lips apart and contributes to the
s1

s2

creation of the seal

There is no pressing or flowing of the flexible sealing lips towards the rubber-steel
gaskets when used in solid profile, as occurs with O or V-rings.
optimum smoothing of any bumps on the flange by the flexible sealing lips,
particularly when a contiguous seal cannot always be guaranteed, as with GRP
flanges.

plastic and GRP flange connections

Sealing vacuum-operated pipeline systems in chemical industry
Gas and water supply
For sealing highly-flexible flanges
with enamel pipelines and apparatus flanges.
J#SRS-03
Features
Easy to replace the rubber sealing rings, meaning the rubber-steel gasket Profile
C#NSRS-03 can be reused again and again.
d3 Safe to use and easy to handle the rubber sealing material, even at large nominal
sizes.
d2
Special sizes can be produced without incurring additional costs, from an internal
d1 diameter of approx. 400mm.
s1

Typical field of application

Sealing tank flange connections.
Sealing special flanges.
Sealing cooling and condensate pipelines in power plants.

4 / 5
4
 JINWOO KOREA
STEEL RUBBER
J#SRS-04 Features
Impossible to overload the rubber sealing ring
Seal is secure, even with large fluctuations or surges in pressure
d3 Impervious to additional pipelines forces
Easy and safe installation, reduces the risk of installation errors caused by applying
d2 too high or uneven bolt tightening torque (the most common reason for the fail-
d1 ure of a rubber-steel gasket) simple replacement of the rubber sealing ring, making
it reusable
s1
s3

Special sizes can be produced without incurring additional costs, from an internal
diameter of approx. 400mm.
Can be used for a range of applications due to the very large range of surface
pressure limits.

High pressure lines such as gas distribution pipelines, gas pressure control systems
Pipeline construction such as in underground pipelines
Flue gas cleaning systems and power plant cooling circuits
Pipeline and apparatus construction with partly-rubber flange sealing surfaces.

In order to determine the flange recess required for the rubber coating we would
be happy to provide our design recommendations.

J#SRS-04HT
Features

research centre, Karlsruhe for conformity with DVGW-VP 401 (01.10.98) for flange
connections in accordance with DIN EN 1092-1.
d3
d2 Has all the features of the rubber-steel gasket Profile C#NSRS-04
d1 Easy to replace the rubber sealing rings and graphite layers, meaning the rubber-
steel gasket Profile C#NSRS-04HT can be reused again and again
s1
s3

Domestic gas supplies with flanged house connection combinations, pressure

regulators and gas meters
Gas stations
Drinking water pipelines with associated fire fighting systems in accordance with
DIN 1988-6.

Installation Instruction
Flanges must be clean, dry and aligned in parallel before work starts.
The gasket must not be damaged.
Separating agents or lubricants containing grease should not come into contact
with the rubber gasket.
Tighten the screws evenly (crosswise) in multiple passes.
The pipeline must be prevented from settling by the use of appropriate supporting
material, otherwise the rubber
gasket will be pinched on one side.
Rubber-steel gaskets should not be used more than once.
 JINWOO KOREA

Metric Unit Conversions

To Convert To SI Units: Multiply By: To Convert To SI Units: Multiply By: To Convert To SI Units: Multiply By:
From: From: From:
Length Force Pressure
mil mm 0.0254 lbf N 4.4482 psi Pa 6894.757
in mm 25.4 kgf N 9.8066 psi kPa 6.8947
in cm 2.54 Weight psi bar 0.069
ft m 0.3048 oz g 28.3495 psi MPa 0.0069
Area oz kg 0.0283 Pa 1.000
6.4516 lb g 453.5924 Torque
0.0929 lb kg 0.4536 in lb Nm 0.113
Volume Density ft lb Nm 1.3558
US gal I 3.7854 1.73 Adhesion
US gal 0.0038 1000 lb/in KN/m 0.1751
16.0185

Temperature Conversion
5 9
Conversion Formulas: C= (F-32), F= (C)+32
9 5
Fahrenheit to Centigrade
-360 to 6 7 to 49 50 to 92 93 to 440 450 to 870 880 to 2000
F C F C F C F C F C F C
-350 -212 7 -13.9 50 10.0 93 33.9 450 232 880 471
-340 -207 8 -13.3 51 10.6 94 34.4 460 238 890 477
-330 -201 9 -12.8 52 11.1 95 35.0 470 243 900 482
-320 -196 10 -12.2 53 11.7 96 35.6 480 249 910 488
-310 -190 11 -11.7 54 12.2 97 36.1 490 254 920 493
-300 -184 12 -11.1 55 12.8 98 36.7 500 260 930 499
-290 -179 13 -10.6 56 13.3 99 37.2 510 266 940 504
-280 -173 14 -10.0 57 13.9 100 37.8 520 271 950 510
-273 -169 15 -9.4 58 14.4 110 43 530 277 960 516
-270 -168 16 -8.9 59 15.0 120 49 540 282 970 521
-260 -162 17 -8.3 60 15.6 130 54 550 288 980 527
-250 -157 18 -7.8 61 16.1 140 60 560 293 990 532
-240 -151 19 -7.2 62 16.7 150 66 570 299 1000 538
-230 -146 20 -6.7 63 17.2 160 71 580 304 1020 549
-220 -140 21 -6.1 64 17.8 170 77 590 310 1040 560
-210 -134 22 -5.6 65 18.3 180 82 600 316 1060 571
-200 -129 23 -5.0 66 18.9 190 88 610 321 1080 582
-190 -123 24 -4.4 67 19.4 200 93 620 327 1100 593
-180 -118 25 -3.9 68 20.0 210 99 630 332 1120 604
-170 -112 26 -3.3 69 20.6 212 100 640 338 1140 616
-160 -107 27 -2.8 70 21.1 220 104 650 343 1160 627
-150 -101 28 -2.2 71 21.7 230 110 660 349 1180 638
-140 -96 29 -1.7 72 22.2 240 116 670 354 1200 649
-130 -90 30 -1.1 73 22.8 250 121 680 360 1220 660
-120 -84 31 -0.6 74 23.3 260 127 690 366 1240 671
-110 -79 32 0.0 75 23.9 270 132 700 371 1260 682
-100 -73 33 0.6 76 24.4 280 138 710 377 1280 693
-90 -68 34 1.1 77 25.0 290 143 720 382 1300 704
-80 -62 35 1.7 78 25.5 300 149 730 388 1350 732
-70 -57 36 2.2 79 26.1 310 154 740 393 1400 760
-60 -51 37 2.8 80 26.7 320 160 750 399 1450 788
-50 -46 38 3.3 81 27.2 330 166 760 404 1500 816
-40 -40 39 3.9 82 27.8 340 171 770 410 1550 843
-30 -34 40 4.4 83 28.3 350 177 780 416 1600 871
-20 -29 41 5.0 84 28.9 360 182 790 421 1650 899
-10 -23 42 5.6 85 29.4 370 188 800 427 1700 927
0 -17.8 43 6.1 86 30.0 380 193 810 432 1750 954
1 -17.2 44 6.7 87 30.6 390 199 820 438 1800 982
2 -16.7 45 7.2 88 31.1 400 204 830 443 1850 1010
3 -16.1 46 7.8 89 31.7 410 210 840 449 1900 1038
4 -15.6 47 8.3 90 32.2 420 215 850 454 1950 1066
5 -15.0 48 8.9 91 32.8 430 221 860 460 2000 1093
6 -14.4 49 9.4 92 33.3 440 227 870 466

6 6 / 7
 JINWOO KOREA

RAISED FACE GASKET FOR ASME B16.5, B16.21, B16.47-B

NOMINAL INSIDE OUTSIDE DIAMETER OD

SIZE Inch DIAMETER ID
Class 150 Class 300 Class 400 Class 600 Class 900
0.50" 21±1.5 48+0-1.5 54+0-1.5 54+0-1.5 54+0-1.5 64+0-1.5
0.75" 27±1.5 57+0-1.5 67+0-1.5 67+0-1.5 67+0-1.5 70+0-1.5
1" 33±1.5 67+0-1.5 73+0-1.5 73+0-1.5 73+0-1.5 79+0-1.5
1.25" 42±1.5 76+0-1.5 83+0-1.5 83+0-1.5 83+0-1.5 89+0-1.5
1.50" 48±1.5 86+0-1.5 95+0-1.5 95+0-1.5 95+0-1.5 98+0-1.5
2" 60±1.5 105+0-1.5 111+0-1.5 111+0-1.5 111+0-1.5 143+0-1.5
2.5" 73±1.5 124+0-1.5 130+0-1.5 130+0-1.5 130+0-1.5 165+0-1.5
3" 89±1.5 137+0-1.5 149+0-1.5 149+0-1.5 149+0-1.5 168+0-1.5
3.5" 102±1.5 162+0-1.5 165+0-1.5 162+0-1.5 162+0-1.5 -
4" 114±1.5 175+0-1.5 181+0-1.5 178+0-1.5 194+0-1.5 206+0-1.5
5" 141±1.5 197+0-1.5 216+0-1.5 213+0-1.5 241+0-1.5 248+0-1.5
6" 168±1.5 222+0-1.5 251+0-1.5 248+0-1.5 267+0-1.5 289+0-1.5
8" 219±1.5 279+0-1.5 308+0-1.5 305+0-1.5 321+0-1.5 359+0-1.5
10" 273±1.5 340+0-1.5 362+0-1.5 359+0-1.5 400+0-1.5 435+0-1.5
12" 324±1.5 410+0-1.5 422+0-1.5 419+0-1.5 457+0-1.5 498+0-1.5
14" 356±3.0 451+0-3.0 486+0-3.0 483+0-3.0 492+0-3.0 521+0-3.0
16" 406±3.0 514+0-3.0 540+0-3.0 537+0-3.0 565+0-3.0 575+0-3.0
18" 457±3.0 549+0-3.0 597+0-3.0 594+0-3.0 613+0-3.0 638+0-3.0
20" 508±3. 0 +0-3.0 54+0-3.0 648+0-3.0 83+0-3.0 699+0-3.0
24" 610±3.0 718+0-3.0 775+0-3.0 768+0-3.0 791+0-3.0 838+0-3.0
26(B)" 660±3.0 725+0-3.0 772+0-3.0 746+0-3.0 765+0-3.0 -
28(B)" 711±3.0 776+0-3.0 826+0-3.0 800+0-3.0 819+0-3.0 -
30(B)" 762±3.0 827+0-3.0 886+0-3.0 857+0-3.0 879+0-3.0 -
32(B)" 813±3.0 881+0-3.0 940+0-3.0 911+0-3.0 933+0-3.0 -
34(B)" 864±3.0 935+0-3.0 994+0-3.0 962+0-3.0 997+0-3.0 -
36(B)" 914±3.0 987+0-3.0 1048+0-3.0 1022+0-3.0 1048+0-3.0 -
38(B)" 965±3.0 1045+0-3.0 1099+0-3.0 - - -
40(B)" 1016±3.0 1095+0-3.0 1149+0-3.0 - - -
42(B)" 1067±3.0 1146+0-3.0 1200+0-3.0 - - -
44(B)" 1118±3.0 1197+0-3.0 1251+0-3.0 - - -
46(B)" 1168±3.0 1256+0-3.0 1318+0-3.0 - - -
48(B)" 1219±3.0 1307+0-3.0 1368+0-3.0 - - -
50(B)" 1270±3.0 1357+0-3.0 1419+0-3.0 - - -
52(B)" 1321±3.0 1408+0-3.0 1470+0-3.0 - - -
54(B)" 1372±3.0 1464+0-3.0 1530+0-3.0 - - -
56(B)" 1422±3.0 1514+0-3.0 1594+0-3.0 - - -
58(B)" 1473±3.0 1580+0-3.0 1656+0-3.0 - - -
60(B)" 1524±3.0 1630+0-3.0 1705+0-3.0 - - -

Unit = mm
 JINWOO KOREA

RAISED FACE GASKET FOR ASME B16.47-A

OUTSIDE DIAMETER OD
NOMINAL INSIDE
SIZE Inch DIAMETER ID
Class 150 Class 300 Class 400 Class 600

22"(A) 559±3.0 660+0-3.0 705+0-3.0 702+0-3.0 733+0-3.0

26"(A) 660±3.0 775+0-3.0 835+0-3.0 832+0-3.0 867+0-3.0

28"(A) 711±3.0 832+0-3.0 899+0-3.0 892+0-3.0 914+0-3.0

30"(A) 762±3.0 883+0-3.0 953+0-3.0 946+0-3.0 972+0-3.0

32"(A) 813±3.0 940+0-3.0 1006+0-3.0 1003+0-3.0 1022+0-3.0

34"(A) 864±3.0 991+0-3.0 1057+0-3.0 1054+0-3.0 1073+0-3.0

36"(A) 914±3.0 1048+0-3.0 1118+0-3.0 1118+0-3.0 1130+0-3.0

38"(A) 965±3.0 1111+0-3.0 1054+0-3.0 1073+0-3.0 1105+0-3.0

40"(A) 1016±3.0 1162+0-3.0 1114+0-3.0 1127+0-3.0 1156+0-3.0

42"(A) 1067±3.0 1219+0-3.0 1165+0-3.0 1178+0-3.0 1219+0-3.0

44"(A) 1118±3.0 1276+0-3.0 1219+0-3.0 1232+0-3.0 1270+0-3.0

46"(A) 1168±3.0 1327+0-3.0 1273+0-3.0 1289+0-3.0 1327+0-3.0

48"(A) 1219±3.0 1384+0-3.0 1324+0-3.0 1346+0-3.0 1391+0-3.0

50"(A) 1270±3.0 1435+0-3.0 1378+0-3.0 1403+0-3.0 1448+0-3.0

52"(A) 1321±3.0 1492+0-3.0 1429+0-3.0 1454+0-3.0 1499+0-3.0

54"(A) 1372±3.0 1549+0-3.0 1492+0-3.0 1518+0-3.0 1556+0-3.0

56"(A) 1422±3.0 1607+0-3.0 1543+0-3.0 1568+0-3.0 1613+0-3.0

58"(A) 1473±3.0 1664+0-3.0 1594+0-3.0 1619+0-3.0 1664+0-3.0

60"(A) 1524±3.0 1715+0-3.0 1645+0-3.0 1683+0-3.0 1721+0-3.0

Unit = mm

8 8 / 9
 JINWOO KOREA

FULL FACE GASKET FOR ASME B16.5, 16.21, B16.47-B

Nominal INSIDE CLASS 150 CLASS 300

Pipe DIAMETER
Size ID Hole Hole
OD BCD H.D OD BCD H.D
No. No.
0.50" 21±1.5 89+0-1.5 60.3±1.5 4 15.8±0.75 95+0-1.5 66.7±1.5 4 15.7±0.75
0.75" 27±1.5 98+0-1.5 69.9±1.5 4 15.8±0.75 117+0-1.5 82.6±1.5 4 19.1±0.75
1" 33±1.5 108+0-1.5 79.4±1.5 4 15.8±0.75 124+0-1.5 88.9±1.5 4 19.1±0.75
1.25" 42±1.5 117+0-1.5 88.9±1.5 4 15.8±0.75 133+0-1.5 98.4±1.5 4 19.1±0.75
1.50" 48±1.5 127+0-1.5 98.4±1.5 4 15.8±0.75 156+0-1.5 114.3±1.5 4 22.4±0.75
2" 60±1.5 152+0-1.5 120.7±1.5 4 19.0±0.75 165+0-1.5 127.0±1.5 8 19.1±0.75
2.50" 73±1.5 178+0-1.5 139.7±1.5 4 19.0±0.75 191+0-1.5 149.2±1.5 8 22.2±0.75
3" 89±1.5 191+0-1.5 152.4±1.5 4 19.0±1.5 210+0-1.5 168.3±1.5 8 22.2±1.5
3.50" 102±1.5 216+0-1.5 177.8±1.5 8 19.0±1.5 229+0-1.5 184.2±1.5 8 22.2±1.5
4" 114±1.5 229+0-1.5 190.5±1.5 8 19.0±1.5 254+0-1.5 200.0±1.5 8 22.2±1.5
5" 141±1.5 254+0-1.5 215.9±1.5 8 22.2±1.5 279+0-1.5 235.0±1.5 8 22.2±1.5
6" 168±1.5 279+0-1.5 241.3±1.5 8 22.2±1.5 318+0-1.5 269.9±1.5 12 22.2±1.5
8" 219±1.5 343+0-1.5 298.5±1.5 8 22.2±1.5 381+0-1.5 330.2±1.5 12 25.4±1.5
10" 273±1.5 406+0-1.5 362.0±1.5 12 25.4±1.5 444.5+0-1.5 387.3±1.5 16 28.4±1.5
12" 324±1.5 483+0-1.5 431.8±1.5 12 25.4±1.5 520.7+0-1.5 450.9±1.5 16 31.8±1.5
14" 356±3.0 533+0-3.0 476.3±1.5 12 28.5±1.5 584.2+0-3.0 514.4±1.5 20 31.8±1.5
16" 406±3.0 597+0-3.0 539.8±1.5 16 28.5±1.5 647.7+0-3.0 571.5±1.5 20 35.1±1.5
18" 457±3.0 635+0-3.0 577.9±1.5 16 31.8±1.5 711.2+0-3.0 628.7±1.5 24 35.1±1.5
20" 508±3.0 699+0-3.0 635.0±1.5 20 31.8±1.5 774.7+0-3.0 685.8±1.5 24 35.1±1.5
24" 610±3.0 813+0-3.0 749.3±1.5 20 35.0±1.5 914.4+0-3.0 812.8±1.5 24 41.1±1.5
26(B)" 660.4±3.0 785.9+0-3.0 744.5±1.5 36 22.2±1.5 866.6+0-3.0 803.1±1.5 32 35.1±1.5
28(B)" 711.2±3.0 836.7+0-3.0 795.3±1.5 40 22.2±1.5 920.8+0-3.0 857.3±1.5 36 35.1±1.5
30(B)" 762.0±3.0 887.5+0-3.0 846.1±1.5 44 22.2±1.5 990.6+0-3.0 920.8±1.5 36 35.1±1.5
32(B)" 812.8±3.0 941.3+0-3.0 900.2±1.5 48 22.2±1.5 1054.1+0-3.0 977.9±1.5 32 38.1±1.5
34(B)" 863.6±3.0 1004.8+0-3.0 957.3±1.5 40 25.4±1.5 1107.9+0-3.0 1031.7±1.5 36 41.1±1.5
36(B)" 914.4±3.0 1057.1+0-3.0 1009.7±1.5 44 25.4±1.5 1171.4+0-3.0 1089.2±1.5 32 41.1±1.5
38(B)" 965.2±3.0 1124+0-3.0 1069.8±1.5 40 28.4±1.5 1222.2+0-3.0 1140.0±1.5 36 44.5±1.5
40(B)" 1016.0±3.0 1174.8+0-3.0 1120.6±1.5 44 28.4±1.5 1273.0+0-3.0 1190.8±1.5 40 44.5±1.5
42(B)" 1066.8±3.0 1225.6+0-3.0 1171.4±1.5 48 28.4±1.5 1333.5+0-3.0 1244.6±1.5 36 44.5±1.5
44(B)" 1117.6±3.0 1276.4+0-3.0 1222.2±1.5 52 28.4±1.5 1384.3+0-3.0 1295.4±1.5 40 47.8±1.5
46(B)" 1168.4±3.0 1341.4+0-3.0 1284.7±1.5 40 31.8±1.5 1460.5+0-3.0 1365.3±1.5 36 47.8±1.5
48(B)" 1219.2±3.0 1392.2+0-3.0 1335.0±1.5 44 31.8±1.5 1511.3+0-3.0 1416.1±1.5 40 50.8±1.5
50(B)" 1270.0±3.0 1443+0-3.0 1385.8±1.5 48 31.8±1.5 1562.1+0-3.0 1466.9±1.5 44 50.8±1.5
52(B)" 1320.8±3.0 1493.8+0-3.0 1436.6±1.5 52 31.8±1.5 1612.9+0-3.0 1517.7±1.5 48 50.8±1.5
54(B)" 1371.6±3.0 1549.4+0-3.0 1492.3±1.5 56 31.8±1.5 1673.4+0-3.0 1577.8±1.5 48 50.8±1.5
56(B)" 1422.4±3.0 1600.2+0-3.0 1543.1±1.5 60 31.8±1.5 1765.3+0-3.0 1651.0±1.5 36 50.8±1.5
58(B)" 1473.2±3.0 1674.9+0-3.0 1611.4±1.5 48 35.1±1.5 1827.3+0-3.0 1713.0±1.5 40 60.5±1.5
60(B)" 1524.0±3.0 1725.7+0-3.0 1662.2±1.5 52 35.1±1.5 1878.1+0-3.0 1763.8±1.5 40 60.5±1.5
Unit = mm
 JINWOO KOREA

FULL FACE GASKET FOR ASME B16.47-A

CLASS 150 CLASS 300

Nominal INSIDE
Pipe DIAMETER
Size ID Hole Hole
OD BCD H.D OD BCD H.D
No. No.

22"(A) 558.8±3.0 749.0+0-3.0 692.2±1.5 20 35.1±1.5 838.0+0-3.0 743.0±1.5 24 41.1±1.5

26"(A) 660.4±3.0 870.0+0-3.0 806.5±1.5 24 35.1±1.5 971.6+0-3.0 876.3±1.5 28 44.5±1.5

28"(A) 711.2±3.0 927.1+0-3.0 863.6±1.5 28 35.1±1.5 1035.1+0-3.0 939.8±1.5 28 44.5±1.5

30"(A) 762.0±3.0 984.3+0-3.0 914.4±1.5 28 35.1±1.5 1092.2+0-3.0 989.7±1.5 28 47.8±1.5

32"(A) 812.8±3.0 1060.5+0-3.0 977.9±1.5 28 41.1±1.5 1149.4+0-3.0 1054.1±1.5 28 50.8±1.5

34"(A) 863.6±3.0 1111.3+0-3.0 1028.7±1.5 32 41.1±1.5 1206.5+0-3.0 1104.9±1.5 28 50.8±1.5

36"(A) 914.4±3.0 1168.4+0-3.0 1085.9±1.5 32 41.1±1.5 1270.0+0-3.0 1168.4±1.5 32 53.8±1.5

38"(A) 965.2±3.0 1238.3+0-3.0 1149.4±1.5 32 41.1±1.5 1168.4+0-3.0 1092.2±1.5 32 41.1±1.5

40"(A) 1016.0±3.0 1289.1+0-3.0 1200.2±1.5 36 41.1±1.5 1238.3+0-3.0 1155.7±1.5 32 44.5±1.5

42"(A) 1066.8±3.0 1346.2+0-3.0 1257.3±1.5 36 41.1±1.5 1289.1+0-3.0 1206.5±1.5 32 44.5±1.5

44"(A) 1117.6±3.0 1403.4+0-3.0 1314.5±1.5 40 41.1±1.5 1352.6+0-3.0 1263.7±1.5 32 47.8±1.5

46"(A) 1168.4±3.0 1454.2+0-3.0 1365.3±1.5 40 41.1±1.5 1416.1+0-3.0 1320.8±1.5 28 50.8±1.5

48"(A) 1219.2±3.0 1511.3+0-3.0 1422.4±1.5 44 41.1±1.5 1466.9+0-3.0 1371.6±1.5 32 50.8±1.5

50"(A) 1270.0±3.0 1568.5+0-3.0 1479.6±1.5 44 47.8±1.5 1530.4+0-3.0 1428.8±1.5 32 53.8±1.5

52"(A) 1320.8±3.0 1625.6+0-3.0 1530.4±1.5 44 47.8±1.5 1581.2+0-3.0 1479.6±1.5 32 53.8±1.5

54"(A) 1371.6±3.0 1682.8+0-3.0 1593.9±1.5 44 47.8±1.5 1657.4+0-3.0 1549.4±1.5 28 60.5±1.5

56"(A) 1422.4±3.0 1746.3+0-3.0 1651.0±1.5 48 47.8±1.5 1708.2+0-3.0 1600.2±1.5 28 60.5±1.5

58"(A) 1473.2±3.0 1803.4+0-3.0 1708.2±1.5 48 47.8±1.5 1759.0+0-3.0 165.01±1.5 32 60.5±1.5

60"(A) 1524.0±3.0 1854.2+0-3.0 1759.0±1.5 52 47.8±1.5 1809.8+0-3.0 1701.8±1.5 32 60.5±1.5

Unit = mm

10 10 / 11
 DISTRIBUTED
DISTRIBUTE BYBY

Head Office
23, Taejang-ro 795beon-gil, Gimpo-si, Gyeonggi-do, Rep. of Korea
Tel : 82-31-986-0116 Fax : 82-31-624-6046

Factory
38, Gyeongjeoncheol-ro 39beon-gil, Gangseo-gu, Busan, Rep. of Korea
Tel : 82-51-971-1630 Fax : 82-51-971-1631

Warehouse
60, Jinwi-ro 328beon-gil, Jinwi-myeon, Pyeongtaek-si, Gyeonggi-do, Rep. of Korea

E-mail : [email protected]