DN-6997:D • A1-320

NH-100(A) Series
Intelligent Addressable Thermal 
Detectors for FireWarden Series
Addressable

General
The NOTIFIER NH-100(A) Series thermal detectors are
addressable sensors that use a state-of-the-art thermistor
sensing circuit for fast response. These sensors provide open-
area protection and are intended for use with FireWarden
Series (FireWarden-100-2 and FireWarden-50) and Spartan
(NSP-25) addressable Fire Alarm Control Panels (FACPs).
The NH-100(A) and NH-100R(A) sensors provide fixed tem-
perature alarm detection at 135°F (57°C). The NH-100R(A)
sensor also responds to rate-of-rise conditions of greater than
15°F (8.3°C) per minute. The NH-100H(A) is a fixed high-tem-

B210-2251.jpg
perature detector that activates at 190°F (88°C). These ther-
mal detectors provide addressable property protection in a
variety of applications.
NH-100(A) in B210LP(A) Base
Two LEDs on each sensor light to provide a local, visible sen-
sor indication. Remote LED annunciator capability is available
using an optional accessory, the RA100Z. • Low standby current.
• 94-5V plastic flammability rating.
Features Options:
SLC loop: • Remote LED output connection to optional RA100Z remote
LED annunciator.
• Two-wire SLC loop connection.
• Flanged surface mounting kit.
• Unit uses base for wiring.
Addressing:
Installation
• Addressable by device.
NH-100(A) Series plug-in intelligent thermal detectors use a
• Rotary, decimal addressing: 01 – 99 with FireWarden-100- detachable base to simplify installation, service and mainte-
2, NSP-25, 01 – 50 with FireWarden-50. nance. Installation instructions are shipped with each detector.
Architecture:
Mount base (all base types) on an electrical backbox which is
• Sleek, low-profile, stylish design. at least 1.5" (3.81 cm) deep. For a chart of compatible junction
• State-of-the-art thermistor technology for fast response. boxes, see DN-60054.
• Integral communications and built-in device-type identifica- NOTE: Because of the inherent supervision provided by the SLC
tion. loop, end-of-line resistors are not required. Wiring “T-taps” or
branches are permitted for Style 4 (Class “B”) wiring only.
• Built-in tamper resistant feature.
• Built-in functional test switch activated by external magnet.
Applications
Operation:
Use thermal detectors for protection of property.
• Factory preset at 135°F (57°C) for the NH-100(A) and NH-
100R(A); 190°F (88°C) for the NH-100H(A).
Construction
• Rate-of-rise triggers at 15°F (8.3°C) per minute for the NH-
100R(A). These detectors are constructed of off-white fire-resistant
• 360°-field viewing angle of the visual alarm indicators (two plastic. The NH-100(A) Series plug-in intelligent thermal
bicolor LEDs). LEDs blink red in Normal condition and turn detectors are designed to commercial standards and offer an
on steady red in Alarm. attractive appearance.
• Visible LEDs “blink” every time the unit is addressed.
Mechanicals:
Operation
Each NH-100(A) Series detector uses one of 99 (FireWarden-
• Sealed against back pressure.
100-2, NSP-25) or 50 (FireWarden-50) possible addresses on
• SEMS screws for wiring of the separate base. a control panel SLC loop. It responds to regular polls from the
• Designed for direct-surface or electrical-box mounting. control panel and reports its type and the status. If it receives a
• Plugs into separate base for ease of installation and main- test command from the panel (or a local magnet test), it stimu-
tenance. lates its electronics and reports an alarm. It blinks its LEDs
when polled and turns the LEDs on when commanded by the
• Separate base allows interchange of photoelectric, ioniza-
panel. The NH-100(A) Series offers features and performance
tion and thermal sensors.
that represent the latest in thermal detector technology.
Other system features:
• Remote test feature from the panel.
• Walk test with address display.

DN-6997:D • 5/17/13 — Page 1 of 2

Spefications INTELLIGENT BASES
Size: 2.1" (5.3 cm) high; base determines diameter. NOTE: “A” suffix indicates ULC Listed model.
NOTE: For details about intelligent bases and their mounting, see
– B210LP(A): 6.1" (15.5 cm) diameter.
DN-60054.
– B501(A): 4.1" (10.4 cm) diameter.
B210LP(A): Plug-in detector base (included); standard U.S.
– B200SR(A): 6.875" (17.46 cm) diameter. flanged low-profile mounting base.
– B224RB(A): 6.2" (15.748 cm) diameter.
B210LPBP: Bulk pack of B210LP; package contains 10.
Shipping weight: 4.8 oz. (137 g).
B501(A): Standard European flangeless mounting base.
Installation temperature:
B501BP: Bulk pack of B501; package contains 10.
– NH-100(A), NH-100R(A): –4°F to 100°F (–20°C to 38°C).
B200SR(A): Intelligent sounder base capable of producing
– NH-100H(A): –4°F to 150°F (–20°C to 66°C). sound output with ANSI Temporal 3 or continuous tone.
Humidity range: 10% to 93% relative humidity (noncon- Replaces B501BH series bases in retrofit applications.
densing).
B224RB(A): Plug-in System Sensor relay base. Screw termi-
Voltage range: 15 to 32 VDC peak. nals: up to 14 AWG (2.0 mm²). Relay type: Form-C. Rating: 2.0
Standby current: 300 μA @ 24 VDC (one communication A @ 30 VDC resistive; 0.3 A @ 110 VDC inductive; 1.0 A @
every five seconds with LED blink enabled). 30 VDC inductive.
LED current: 6.5 mA @ 24 VDC. B224BI(A): Plug-in System Sensor isolator detector base.
Maximum 25 devices between isolator bases (see DN-6994).
Mounting: B210LP(A) flanged base, included. See “Product
Line Information: Intelligent Bases” if using a different base. ACCESSORIES
Fixed-temperature setpoint: 135°F (57°C) for the NH-100 F110: Retrofit flange to convert B210LP(A) to match the
and NH-100R(A)(A); 190°F (88°C) for the NH-100H(A). B710LP(A) profile, or to convert older high-profile bases to
low-profile.
Rate-of-rise detection: responds to greater than 15°F (8.3°C)
per minute. F110BP: Bulk pack of F110; package contains 15.
F210: Replacement flange for B210LP(A) base.
Listings and Approvals RA100Z(A): Remote LED annunciator. 3 – 32 VDC. Mounts to
Listings and approvals below apply to the NH-100(A) Series a U.S. single-gang electrical box. For use with B501(A) and
detectors. In some cases, certain modules may not be listed B210LP(A) bases only.
by certain approval agencies, or listing may be in process. SMB600: Surface mounting kit
Consult factory for latest listing status.
M02-04-00:Test magnet.
• UL Listed: S747.
• ULC Listed: S747. M02-09-00: Test magnet with telescoping handle.
• CSFM: 7270-0028:0234. XR2B: Detector removal tool. Allows installation and/or
removal of detector heads from bases in high ceiling applica-
• MEA: 387-02-E Vol. II.
tions.
• FM approved.
XP-4: Extension pole for XR2B. Comes in three 5-foot (1.524
m) sections.
Product Line Information
T55-127-010: Detector removal tool without pole.
NOTE: “A” suffix indicates ULC Listed model.
NH-100: Intelligent thermal sensor; 135° F (57° C); B210LP
base included.
NH-100A: Same as NH-100 but with ULC Listing; B210LPA
base included.
NH-100R: Same as NH-100 with rate-of-rise feature; B210LP
base included.
NH-100RA: Same as NH-100R but with ULC Listing; B210LPA
base included.
NH-100H: Intelligent fixed high-temperature thermal detector;
190° F (88° C); B210LP base included.
NH-100HA: Same as NH-100H but with ULC Listing; B210LPA
base included.
NOTIFIER® and FireWarden® are registered trademarks of Honeywell
International Inc. 
©2013. All rights reserved. Unauthorized use of this document is strictly
prohibited.

This document is not intended to be used for installation purposes.

We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
Made in the U.S. A.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com

Page 2 of 2 — DN-6997:D • 5/17/13