0% found this document useful (0 votes)
22 views

10307699-USER MANUAL-ENG-RCF UPDATER

Resi jdkambaum roklo

Uploaded by

ilhamemail678
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
22 views

10307699-USER MANUAL-ENG-RCF UPDATER

Resi jdkambaum roklo

Uploaded by

ilhamemail678
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

RCF SpA RCF Updater Manual v1.0 – pag.

1 11/07/2024
WINDOWS INSTALLATION
Requirements: Windows 10 or 11, 64-bit version

1) Unzip the installer file to a temporary folder.


2) From the temporary folder, double click on the executable installer file to launch the installation, and follow
the on-screen instructions pressing the “Next” and then “Install” buttons.
3) When the installation is complete, check the “Launch RCF Updater.exe” checkbox and click on the “Finish”
button to launch RCF Updater.

0
RCF SpA RCF Updater Manual v1.0 – pag. 2 11/07/2024
MAC OS INSTALLATION
Requirements: macOS 10.14 (Mojave) or later

1) Open the RCF Updater disk image (DMG) file from the downloaded ZIP file and drag “RCF Updater” to the
“Applications” folder.

2) RCF Updater will appear in your Mac applications, double click on it to launch it.

RCF SpA RCF Updater Manual v1.0 – pag. 3 11/07/2024


FIRMWARE UPDATE
This section describes how to perform a firmware update on your RCF speaker.

1) Open RCF Updater.

2) Connect your RCF speaker to your PC through the service port using an appropriate USB cable (on ART 9-AX,
SUB AX models: micro USB). As soon as the speaker is detected, the following screen will appear:

In case the current speaker firmware version is newer than the latest displayed on RCF Updater, your version of
RCF Updater is outdated. In this case, please go to the RCF website and download the latest version of RCF
Updater. Otherwise, if you proceed with the firmware update, the speaker firmware version will be downgraded
to the one displayed as “Latest” on RCF Updater.
RCF SpA RCF Updater Manual v1.0 – pag. 4 11/07/2024
3) Click on the “Update” button. The following pop up will be shown:

4) As soon as the “Start” button is clicked, the speaker will be automatically rebooted, then the firmware update
procedure will begin and may take up to a few minute to complete.

RCF SpA RCF Updater Manual v1.0 – pag. 5 11/07/2024


5) After the firmware update is completed, wait for the speaker to reboot and reconnect, then check that the
current version is the same as the latest one.

The firmware update is now completed and your speaker is ready to play.

Troubleshooting:

If anything goes wrong during the firmware update (e.g., the USB cable is detached or the power goes out) an
error screen will be shown. In such a case, a manual firmware update may be required to restore the speaker.

RCF SpA RCF Updater Manual v1.0 – pag. 6 11/07/2024


MANUAL FIRMWARE UPDATE
If the firmware of your speaker is corrupted, RCF Updater may not be able to automatically connect to the
speaker and a manual firmware update is required.

Before to start, the speaker must be rebooted in firmware update mode by powering up while pressing the
volumer encoder knob.

Hold the knob pressed and


power up the speaker

1) In the utilities menu, click on Manual Firmware Update.

RCF SpA RCF Updater Manual v1.0 – pag. 7 11/07/2024


2) Select your speaker series, then model and firmware version. In the example, an ART 912-AX is shown.

3) Click on “Start” button. If your speaker is in firmware update mode, RCF Updater will detect it and allow the
update to begin, otherwise it will show an error message.

Error message: speaker was not detected. In Speaker detected. Click “YES”
this case, follow the instructions to reboot it to start the firmware update
in firmware update mode procedure

After the “YES” button is clicked, the firmware update will start. Steps 4) and 5) are the same as the ones in page
4 and page 5.

RCF SpA RCF Updater Manual v1.0 – pag. 8 11/07/2024

You might also like