AV RECEIVER/AV AMPLIFIER

RX-V663/HTR-6160/
DSP-AX763
SERVICE MANUAL

IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already
known and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal
injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,
we advise all YAMAHA product owners that any service required should be performed by an authorized
YAMAHA Retailer or the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and
service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable
and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please
contact the distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.

RX-V663/HTR-6160/
■ CONTENTS

DSP-AX763
TO SERVICE PERSONNEL .......................................... 2 DISPLAY DATA ........................................................... 63
FRONT PANELS ........................................................ 3–5 IC DATA ................................................................. 64–80
REAR PANELS .......................................................... 6–9 PIN CONNECTION DIAGRAMS ............................ 81–84
REMOTE CONTROL PANELS .................................... 10 BLOCK DIAGRAMS .............................................. 85–89
SPECIFICATIONS / ................................ 11–13 PRINTED CIRCUIT BOARDS .............................. 90–103
INTERNAL VIEW ......................................................... 14 SCHEMATIC DIAGRAMS .................................. 105–115
DISASSEMBLY PROCEDURES / .......... 14–19 REPLACEMENT PARTS LIST .......................... 117–145
UPDATING FIRMWARE REMOTE CONTROL .......................................... 146–151
.................................. 20–34 ADVANCED SETUP / .... 152–155
SELF DIAGNOSIS FUNCTION (DIAG) Using Bluetooth components /
.................................. 35–61 ........................................ 155
CONFIRMATION OF IDLING CURRENT OF AMP UNIT
............... 62

101087 2008 All rights reserved.

This manual is copyrighted by YAMAHA and may not be copied or
redistributed either in print or electronically without permission.
P.O.Box 1, Hamamatsu, Japan
'08.03
 RX-V663/HTR-6160/DSP-AX763

■ TO SERVICE PERSONNEL AC LEAKAGE

1. Critical Components Information WALL EQUIPMENT TESTER OR
Components having special characteristics are marked s OUTLET UNDER TEST EQUIVALENT
and must be replaced with parts having specifications equal
to those originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated INSULATING
TABLE
from supply circuits.
● Meter impedance should be equivalent to 1500 ohms shunted ● Leakage current must not exceed 0.5mA.
by 0.15µF. ● Be sure to test for leakage with the AC plug in both polarities.

For U model
“CAUTION”
“F2501, F2502: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE 10A, 125V FUSE.”

For C model
CAUTION
F2501, F2502: REPLACE WITH SAME TYPE 10A, 125V FUSE.
ATTENTION
F2501, F2502: UTILISER UN FUSIBLE DE RECHANGE DE MÉME TYPE DE 10A, 125V.

WARNING: CHEMICAL CONTENT NOTICE!

This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive
harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY
REASON WHAT SO EVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose
eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.
RX-V663/HTR-6160/

About lead free solder /

DSP-AX763

All of the P.C.B.s installed in this unit and solder joints are
soldered using the lead free solder.
Among some types of lead free solder currently available,
it is recommended to use one of the following types for the
repair work.
• Sn + Ag + Cu (tin + silver + copper)
• Sn + Cu (tin + copper)
• Sn + Zn + Bi (tin + zinc + bismuth)

Caution:
As the melting point temperature of the lead free solder is
about 30°C to 40°C (50°F to 70°F) higher than that of the lead
solder, be sure to use a soldering iron suitable to each solder.

2
 RX-V663/HTR-6160/DSP-AX763

■ REMOTE CONTROL PANELS

• RAV285 • RAV330 • RAV372
RX-V663 (U, C models) RX-V663 (R, T, A, L models) RX-V663 (K, G, E, F models)
HTR-6160 (U, C models) DSP-AX763 (J model) HTR-6160 (F model)
DSP-AX763 (B model)
RX-V663/HTR-6160/
DSP-AX763

10
 RX-V663/HTR-6160/DSP-AX763

■ SPECIFICATIONS
■ Audio Section / ■ General /
Minimum RMS Output Power (Power Amp. Section) / Signal to Noise Ratio / (IHF-A network) Power Supply / Bluetooth is a registered trademark of the Bluetooth SIG and is used
PHONO (MM) (Input shorted) to REC OUT U, C models ........................................................... AC 120 V, 60 Hz by Yamaha in accordance with a license agreement.
[RX-V663/DSP-AX763] (20 Hz to 20 kHz) R, T models (5 mV) ................................................. 86 dB or more R model ................................ AC 110/120/220/230-240 V, 50/60 Hz
U, C, R, T, K, A, B, G, E, F, L models (0.06 % THD, 8 ohms) K, A, B, G, E, F, L models (5 mV) .......................... 81 dB or more T model .................................................................. AC 220 V, 50 Hz
J model (0.09 % THD, 6 ohms) J model (2.5 mV) ..................................................... 80 dB or more K model .................................................................. AC 220 V, 60 Hz
FRONT L/R ............................................................. 95 W + 95 W CD, etc. (Effect off) (Input shorted) to SP OUT A model .................................................................. AC 240 V, 50 Hz
CENTER ............................................................................. 95 W 250 mV .................................................................. 100 dB or more B, G, E, F models .................................................. AC 230 V, 50 Hz
SURROUND L/R .................................................... 95 W + 95 W Residual Noise / (IHF-A network) L model .............................................. AC 220/230-240 V, 50/60 Hz “HDMI”, the “HDMI” logo and “High-Definition Multimedia Interface”
SURROUND BACK L/R ......................................... 95 W + 95 W FRONT L/R, SP OUT ............................................... 150 µV or less J model ............................................................ AC 100 V, 50/60 Hz are trademarks or registered trademarks of HDMI Licensing LLC.
[HTR-6160] (1 kHz, 0.7 % THD, 8 ohms) Channel Separation / (1 kHz/10 kHz) Power Consumption /
FRONT L/R ........................................................ 110 W + 110 W PHONO (Input shorted) U, C models ............................................................ 400 W / 500 VA
CENTER ........................................................................... 110 W R, T, K, A, B, G, E, F, L, J models ..... 60 dB or more/55 dB or more R, T, K, A, B, G, E, F, L models ............................................ 440 W
SURROUND L/R ............................................... 110 W + 110 W CD, etc. (Input 5.1 k-ohms shorted) ..... 60 dB or more/45 dB or more J model .................................................................................. 300 W
SURROUND BACK L/R ..................................... 110 W + 110 W Standby Power Consumption (reference data) /
Volume Control / “x.v.Color” is a trademark of Sony Corporation.
Maximum Power / (JEITA, 1 kHz, 10 % THD) ............................................ MUTE/-80 dB to +16.5 dB/0.5 dB step U, C models ............................................................................ 0.8 W
FRONT L/R R, T, K, A, B, G, E, F, L, J models ......................................... 0.1 W
Tone Control Characteristics /
R, T, K, L models (8 ohms) .................................. 135 W + 135 W Maximum Power Consumption (6ch drive, 10 % THD)
BASS
J model (6 ohms) ................................................. 135 W + 135 W
Boost/Cut ............................................ ± 10 dB/2 dB (step 50 Hz) R model .................................................................................. 850 W
CENTER
Turnover frequency ............................................................ 350 Hz AC Outlets / “SILENT CINEMA” is a trademark of Yamaha Corporation.
R, T, K, L models (8 ohms) ................................................. 135 W
TREBLE 2 switched outlets
J model (6 ohms) ................................................................ 135 W
Boost/Cut ........................................... ± 10 dB/2 dB (step 20 kHz) U, C, T, J models ............................................... 100 W max. total
SURROUND L/R
Turnover frequency ........................................................... 3.5 kHz R, G, E, F, L models ............................................ 50 W max. total
R, T, K, L models (8 ohms) .................................. 135 W + 135 W
Filter Characteristics / 1 switched outlet
J model (6 ohms) ................................................. 135 W + 135 W
(fc=40/60/80/90/100/110/120/160/200 Hz) A, B models ................................................................ 100 W max.
SURROUND BACK L/R
R, T, K, L models (8 ohms) .................................. 135 W + 135 W FRONT, CENTER, SURROUND, SURROUND BACK small Dimensions / (W x H x D) The XM name and related logos are registered trademarks of XM
J model (6 ohms) ................................................. 135 W + 135 W (H.P.F.) .......................................................................... 12 dB/oct. ............................ 435 x 171 x 393 mm (17-1/8" x 6-3/4" x 15-1/2") Satellite Radio Inc.
SUBWOOFER (L.P.F.) .................................................... 24 dB/oct. Weight /
Max. Power Per Channel
(SP impedance set: 8 ohms minimum, 1 kHz, 0.7 % THD, 4 ohms) ................................................................................ 11.8 kg (26 lbs)
■ Video Section /
B, G, E, F, L models Finish /
FRONT L/R .......................................................... 145 W + 145 W Video Signal Type / [RX-V663] Neural Surround™ name and related logos are trademarks owned by
CENTER .............................................................................. 145 W Gray back Gold color ................................................................... R, T models Neural Audio Corporation.
SURROUND L/R .................................................. 145 W + 145 W U, C, R, K, J models ............................................................ NTSC Black color ........................................... U, C, R, A, G, E, F models
SURROUND BACK L/R ........................................ 145 W + 145 W T, A, B, G, E, F, L models ....................................................... PAL Titanium color ............................................... K, G, E, F, L models
IEC Power (1 kHz, 0.06 % THD, 8 ohms) Video conversion ............................................................ NTSC/PAL [HTR-6160]
B, G, E, F, L models Composite Video Signal Level / Black color ............................................................. U, C, F models ©2006 SIRIUS Satellite Radio Inc. “SIRIUS”, “SiriusConnect”, the
FRONT L/R .......................................................... 105 W + 105 W .............................................................................. 1 Vp-p / 75 ohms Titanium color ................................................................... F model SIRIUS dog logo, channel names and logos are trademarks of
Dynamic Power Per Channel / (IHF) S-Video Signal Level / [DSP-AX763] SIRIUS Satellite Radio Inc.
Y ............................................................................ 1 Vp-p / 75 ohms Gold color .......................................................................... J model
FRONT L/R (8/6/4/2 ohms)
C ..................................................................... 0.286 Vp-p / 75 ohms Black color ................................................................... B, J models
U, C, R, T, K, A, B, G, E, F, L models ........... 130/165/195/240 W
J model ............................................................... –/135/165/210 W Component Video Signal Level / Titanium color .................................................................. B model
Y ............................................................................ 1 Vp-p / 75 ohms Accessories /
Dynamic Headroom
U, C models (8 ohms) ............................................................ 1.4 dB Cb/Cr .................................................................. 0.7 Vp-p / 75 ohms Remote control x 1, Batteries (R6, AA, UM-3) x 2 (U, C, R, T, A, L, J
D5-Video Signal Level / (J model) models) / (R03, AAA, UM-4) x 4 (K, B, G, E, F models), Indoor FM
Damping Factor / antenna x 1 (U, C, R, T, K, A, G, E, F, L, J models), AM loop antenna • DIMENSIONS

(7/8")
Y ............................................................................ 1 Vp-p / 75 ohms

21.7
FRONT L/R (20 Hz to 20 kHz, SPEAKER-A, 8 ohms) ...... 120 or more x 1 (U, C, R, T, K, A, G, E, F, L, J models), Optimizer microphone x
Input Sensitivity/Input Impedance / Cb/Cr .................................................................. 0.7 Vp-p / 75 ohms
1, Power cable x 1 (J model)
(1 kHz, 100 W/8 ohms) Video Maximum Input Level /
PHONO (MM) VIDEO CONV. OFF .............................................. 1.5 Vp-p or more * Specifications are subject to change without notice due to product
R, T, K, A, B, G, E, F, L, J models ................ 3.5 mV / 47 k-ohms Video Signal to Noise Ratio / improvements.
CD, etc. ............................................................ 200 mV / 47 k-ohms VIDEO CONV. OFF ................................................... 50 dB or more
MULTI CH INPUT Monitor Out Frequency Response /
FRONT L/R, CENTER, SURROUND L/R, SURROUND BACK L/R, (VIDEO CONV. OFF)

352.3 (13-7/8")
U .......... U.S.A. model B .......... British model

285.5 (11-1/4")

393 (15-1/2")
SUBWOOFER Component video signal level .................... 5 Hz to 100 MHz, -3 dB
.................................................................... 200 mV / 47 k-ohms D5-video signal level (J model) .................. 5 Hz to 100 MHz, -3 dB C .......... Canadian model G .......... European model
Maximum Input Signal Level / (1 kHz) R .......... General model E .......... South European model
HDMI ..................................................................................... Ver. 1.3a
PHONO (MM) (0.1 % THD) T .......... Chinese model F .......... Russian model
R, T, K, A, B, G, E, F, L, J models ........................ 60 mV or more ■ FM Section / [U, C, R, T, K, A, G, E, F, L, J models] K .......... Korean model L .......... Singapore model
CD, etc. (Effect on) (0.5 % THD) ............................... 2.3 V or more A .......... Australian model J ........... Japanese model
Tuning Range /
Output Level/Output Impedance / U, C models ........................................................ 87.5 to 107.9 MHz
REC OUT ........................................................ 200 mV / 1.2 k-ohms R, L models ............................ 87.5 to 108.0 / 87.50 to 108.00 MHz
PRE OUT (FRONT L/R, CENTER, SURROUND L/R, T, K, A, G, E, F models .................................. 87.50 to 108.00 MHz
SURROUND BACK L/R) .................................. 1.0 V / 1.2 k-ohms J model ................................................................. 76.0 to 90.0 MHz
SUBWOOFER (2ch stereo & FRONT L/R SP: small) 50dB Quieting Sensitivity / (IHF, 1 kHz, 100 % MOD.)

(3/4")
.......................................................................... 2.0 V / 1.2 k-ohms

19
Mono ..................................................................... 2.8 µV (20.2 dBf) Manufactured under license from Dolby Laboratories.
[RX-V863 (U, C, R, T, K, A, G, E, F, L models)/HTR-6180 (U, F models)] “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of
ZONE2 OUT ................................................. 200 mV / 1.2 k-ohms Signal to Noise Ratio / (IHF)
Mono / Stereo ............................................................. 73 dB / 70 dB Dolby Laboratories.
Headphone Jack Rated Output/Impedance /

150 (5-15/15")
Harmonic Distortion / (1 kHz)

171 (6-3/4")
CD, etc. (1 kHz, 50 mV, 8 ohms) ..................... 150 mV / 100 ohms Mono / Stereo ............................................................. 0.5 % / 0.5 %
Frequency Response / (10 Hz to 100 kHz) Antenna Input / ......................... 75 ohms unbalanced
CD, etc. to FRONT L/R (Pure direct) .............................. +0/-3.0 dB ■ AM Section / [U, C, R, T, K, A, G, E, F, L, J models]
RIAA Equalization Deviation / (20 Hz to 20 kHz)
PHONO (MM) Tuning Range / DTS is a registered trademark and the DTS logos, Symbol, DTS-HD
R, T, K, A, B, G, E, F, L, J models ............................... 0 ± 0.5 dB U, C models .......................................................... 530 to 1,710 kHz and DTS-HD Master Audio are trademark of DTS, Inc. 395 (15-9/16")

(13/16")
R, L models ................................... 530 to 1,710 / 531 to 1,611 kHz
Total Harmonic Distortion / (20 Hz to 20 kHz)

21
T, K, A, G, E, F, J models ..................................... 531 to 1,611 kHz 435 (17-1/8")
PHONO (MM) to REC OUT (1 V)
R, T, K, A, B, G, E, F, L, J models ......................... 0.02 % or less Antenna Input / .................................... Loop antenna
CD, etc. (2ch stereo) to FRONT L/R SP OUT (50 W, 8 ohms)
................................................................................. 0.06 % or less “iPod” is a trademark of Apple Inc., registered in the U.S. and other Unit: mm (inch)
countries.

11
 RX-V663/HTR-6160/DSP-AX763

• SELECT MENU

3
PARAMETER

Presence R Level
Surround R Level

Presence L Level
Surround L Level
Sur. Room Size

SB. Room Size

Sur.Back Level
Sur. Init. Delay

SB. Init. Delay

Sur. Liveness

Center Image
Decode Type

SB. Liveness

Center Width
Center Level
Dialogue Lift

Effect Level
0 to 250 ms
1.0 to 5.0 s
-6 to +3 dB

Rev. Delay
Room Size

0 to 100 %

0 to 100 %

0 to 100 %

0 to 100 %

0 to 100 %

0 to 100 %

0 to 100 %
Rev. Level
DSP Level

Dimension
1 to 99 ms

1 to 49 ms

1 to 49 ms

Panorama
Rev. Time
Init. Delay

0.1 to 2.0

0.1 to 2.0

0.1 to 2.0

0.0 to 1.0
High/Low
Liveness

TruBass
Auto/Off

Initialize
FOCUS
-3 to +3

0 to 8

0 to 8
0 to 10

0 to 10

0 to 10

On/Off
Direct
0 to 5

0 to 7
CATEGORY SOUND FIELD
CLASSICAL Hall in Munich
Hall in Vienna
Chamber
LIVE/CLUB Cellar Club
The Roxy Theatre
The Bottom Line
ENTERTAINMENT Sports
Action Game
Roleplaying Game
Music Video
MOVIE Standard
Spectacle
Sci-Fi
Adventure
Drama
Mono Movie
STEREO 2ch Stereo
7ch Stereo
MUSIC ENHANCER Straight Enhancer
7ch Enhancer
SUR. DECODE Surround Decoder
STRAIGHT

• SCENE TEMPLATE

Program NIGHT Select (Default)

SCENE name Contents Source R, T, K, A, B, G,
Mode Sub-mode Mode U, C models
E, F, L, J models
DVD Viewing DVD DVD Movie STRAIGHT – SYSTEM O (SCENE 1) O
DVD Movie Viewing DVD MOVIE Sci-Fi SYSTEM O O (SCENE 1)
DVD Live Viewing Music Live DVD ENTERTAINMENT Music Video SYSTEM O O
DVR Viewing DVR DVR MOVIE Drama SYSTEM O O
Disc Hi-Fi ListeningDVD-Audio / Music Disc DVD PURE DIRECT – SYSTEM O O
1 Decode Type Music Disc ListeningSA-CD / CD DVD STEREO 2ch Stereo SYSTEM O O (SCENE 2)
Decode Type PL II x Movie PL II when Surround Back is None. / Disc Listening DVD STEREO 7ch Stereo SYSTEM O (SCENE 2) O
Neo:6 Cinema CD Hi-Fi Listening CD Music Disc CD PURE DIRECT – SYSTEM O O
CD Listening CD STEREO 7ch Stereo SYSTEM O O
2 Decode Type CD Music Listening CD STEREO 2ch Stereo SYSTEM O O
Decode Type Pro Logic Radio Listening TUNER/RADIO FM/AM FM/AM
MUSIC ENHANCER 7ch Enhancer SYSTEM O (SCENE 4) O (SCENE 4)
PL II x Movie PL II when Surround Back is None. / (TUNER)
PL II x Music PL II when Surround Back is None. /
XM Listening XM XM MUSIC ENHANCER 7ch Enhancer SYSTEM O –
PL II x Game PL II when Surround Back is None. /
SIRIUS Listening SIRIUS SIRIUS MUSIC ENHANCER 7ch Enhancer SYSTEM O –
Neo:6 Cinema
Neo:6 Music Dock Listening DAP iPod DOCK
MUSIC ENHANCER 7ch Enhancer SYSTEM O O
Neural Sur. (U, C models) Bluetooth (V-AUX)
TV Viewing TV DTV/CBL STRAIGHT – SYSTEM O (SCENE 3) O (SCENE 3)
TV Sports Viewing DTV/CBL ENTERTAINMENT Sports SYSTEM O O
Action Game Playing GAME Action V-AUX ENTERTAINMENT Action Game SYSTEM O O
RPG Playing RPG V-AUX ENTERTAINMENT Roleplaying Game SYSTEM O O
LP Record Listening LP Record LP PHONO PURE DIRECT – SYSTEM – O

12
 • SET MENU TABLE /

CATEGORY MAIN MENU SUB MENU SELECT MENU VALUE [INITIAL]

AUTO SETUP Use this feature to automatically adjust speaker and system parameters.

MANUAL SETUP 1 BASIC MENU A) SPEAKER SET EXTRA FRONT B ZONE2 / [FRONT B] / ZONE B / PRNS / NONE
BASS OUT BOTH [BOTH] / SWFR / FRONT
FRONT LARGE [LARGE] / SMALL
CENTER SMALL
LARGE / [SMALL] / NONE
SUR. L/R SMALL
SUR. B SMLx2 LRGx1 / LRGx2 / SMLx1 / [SMLx2] / NONE
CROSSOVER 80Hz 40 / 60 / [80] / 90 / 100 / 110 / 120 / 160 / 200 Hz
SWFR PHASE NRM [NRM (normal)] / REV (reverse)
B) SP LEVEL FL – – – – –| |– – – – –
-10.0 to +10.0 dB, [0 dB], 0.5 dB step
FR – – – – –| |– – – – –
C – – – – –| |– – – – –
SL – – – – –| |– – – – –
SR – – – – –| |– – – – – -10.0 to +10.0 dB, [-1.0 dB], 0.5 dB step
SBL – – – – –| |– – – – –
SBR – – – – –| |– – – – –
SWFR – – – – –| |– – – – –
PL – – – – –| |– – – – – -10.0 to +10.0 dB, [0 dB], 0.5 dB step
PR – – – – –| |– – – – –
C) SP DISTANCE UNIT feet feet (ft) / meters (m)
FRONT L 10.0ft
feet: 1.0 to 80.0 ft [10.0 ft], 0.5 ft step
FRONT R 10.0ft
CENTER 8.5ft feet: 1.0 to 80.0 ft [8.5 ft], 0.5 ft step
SUR. L 8.0ft
UNIT: feet SUR. R 8.0ft
feet: 1.0 to 80.0 ft [8.0 ft], 0.5 ft step
SBL 8.0ft
SBR 8.0ft
SWFR 10.0ft
PRNS L 10.0ft feet: 1.0 to 80.0 ft [10.0 ft], 0.5 ft step
PRNS R 10.0ft
FRONT L 3.00m
meters: 0.30 to 24.00 m [3.00 m], 0.10 m step
FRONT R 3.00m
CENTER 2.60m meters: 0.30 to 24.00 m [2.60 m], 0.10 m step
SUR. L 2.40m
UNIT: meters SUR. R 2.40m
meters: 0.30 to 24.00 m [2.40 m], 0.10 m step
SBL 2.40m
SBR 2.40m
SWFR 3.00m
PRNS L 3.00m meters: 0.30 to 24.00 m [3.00 m], 0.10 m step
PRNS R 3.00m
D) TEST TONE > OFF ON [OFF] / ON
2 VOLUME MENU ADPTV DRC OFF
AUTO / [OFF]
ADAPTV DSP OFF
MUTE TYP. FULL [FULL] / -20 dB
MaxVol. +16.5dB -30.0 to +15.0 dB / +16.5 dB, [+16.5 dB], 5.0 dB step
IniVol. OFF OFF / MUTE / -80.0 to +16.5 dB, [OFF], 0.5 dB step
3 SOUND MENU A) EQUALIZER EQ SELECT GEQ AUTO PEQ / [GEQ] / OFF
CHANNEL FRNT L / FRNT R / CENTER / SUR. L / SUR. R / SBL / SBR / SWFR / PRNS L / PRNS R
63 Hz – – –| |– – –
160 Hz – – –| |– – –
400 Hz – – –| |– – –
1 kHz – – –| |– – – -0.6 to +6.0 dB, [0 dB], 0.5 dB step
2.5 kHz – – –| |– – –
6.3 kHz – – –| |– – –
16 kHz – – –| |– – –
TEST TONE OFF [OFF] / ON
B) LFE LEVEL SP LFE
-20 to 0 dB, [0 dB], 1 dB step
HP LFE
C) D. RANGE SP
MIN/AUTO / STD / [MAX]
HP
D) LIPSYNC HDMI AUTO OFF ON / [OFF]
AUTO – – – ms
0 to 240 ms, [0 ms], 1 ms step
MANUAL 0 ms
E) EXTD SUR. EXTD AUTO [AUTO] / PLIIxMovie / PLIIxMusic / EX/ES / EX / OFF
4 INPUT MENU A) SIRIUS Items that can be set. / : [2], [3], [5]
(U, C models) B) XM : [2], [3]
(R, T, K, A, B, C) PHONO : [1], [2], [3], [4]
G, E, F, L, J D) TUNER : [2], [3]
models) E) CD : [1], [2], [3], [4]
F) MD/CD-R : [1], [2], [3], [4]
G) DVD : [1], [2], [3], [4]
H) DTV/CBL : [1], [2], [3], [4]
I) V-AUX : [1], [2], [3], [4]
J) DOCK : [2], [3], [6]
K) BLUETOOTH : [2], [3], [7]
L) DVR : [1], [2], [3], [4]
M) VCR : [1], [2], [3], [4]
N) MULTI CH : [2], [3], [8], [9], [10]
[1] I/O ASSIGNMENT COAX. IN NONE NONE / CD / DVD
OPT. IN NONE NONE / MD/CD-R / DVD / DTV/CBL
OPT. OUT NONE NONE / MD/CD-R
[2] INPUT RENAME Input is possible to 9 characters /
Input possible Character type /
Capital / : A to Z Small / : a to z Figure / : 0 to 9
Space / Marks / :#*+,-./:<>?
[3] V. TRIM 0.0dB -6.0 to +6.0 dB, [0.0 dB], 0.5 dB step
[4] DECODER AUTO [AUTO] / DTS
(U, C models) [5] PARENTAL LOCK
[6] CHARGE AUTO [AUTO] / OFF
[7] START PAIRING
[8] BGV LAST [LAST] / DVD, DTV/CBL, DVR, VCR, V-AUX / OFF
[9] INPUT CH 6ch [6ch] / 8ch
[10] FRONT DVD CD / MD/CD-R / [DVD] / DTV/CBL / DVR / VCR / V-AUX
* Setting is possible only when 8ch is selected using [9 (INPUT CH)]. /
5 OPTION MENU A) DISPLAY SET DIMMER 0 -4 to 0, [0], 1 step
OSD SHIFT 0 -5 (downward) to +5 (upward), [0], 1 step
OSD-SOURCE 30s
ON / 10s / 30s
OSD-AMP 30s
FL SCROLL COTN [CONT] / ONCE
B) VIDEO SET VIDEO CONV. ON [ON] / OFF
C) MEMORY GUARD MEM. GUARD OFF [OFF] / ON
D) INIT. CONFIG A. SELECT AUTO
DECODER AUTO [AUTO] / LAST
EXTD SUR. AUTO
E) HDMI SET HDMI CONTROL OFF ON / [OFF]
S. AUDIO V663 [V663 / 6160 / AX763] / OTHER
(RX-V663, (J model) STANDBY THROUGH OFF ON / [OFF]
HTR-6160: F) ZONE2 SET MAX VOL. +16.5dB -30.0 to +15.0 dB / +16.5 dB, [+16.5 dB], 5.0 dB step
U, F models) INI. VOL. OFF OFF / MUTE / -80.0 to +16.5 dB, [OFF], 0.5 dB step
SIGNAL INFO AUDIO FORMAT (Signal format) Analog / – – – / – – – / – – – / – – – / – – – / – – –
SAMPLING
CHANNEL
BITRATE 3/2/0.1 (front/surround/LFE)
DIALOG
FLAG DTS, Dolby Digital, or PCM
VIDEO HDMI SIGNAL xxx –> xxx
HDMI RES. 1080p –> 1080p
ANALOG RES. 480/576i
HDMI ERROR (HDMI MESSAGE) DEVICE OVER / HDCP ERROR / Out of Res.
RX-V663/HTR-6160/DSP-AX763

13
 RX-V663/HTR-6160/DSP-AX763

■ INTERNAL VIEW ■ DISASSEMBLY PROCEDURES

• Top view (Remove parts in the order as numbered.)
Disconnect the power cable from the AC outlet.
12 3 4 56 7 8 9 0 A B CD 1 POWER TRANSFORMER
2 FUNCTION (6) P.C.B. 1. Removal of Top Cover
3 FUNCTION (3) P.C.B. a. Remove 4 screws (1), 5 screws (2) and screw (3). 1 2 3
4 FUNCTION (2) P.C.B. (J model) (Fig. 1)
5 VIDEO (2) P.C.B. b. Slide the top cover rearward to remove it. (Fig. 1)
6 VIDEO (1) P.C.B.
7 FUNCTION (4) P.C.B. (R, L models)
8 MAIN (1) P.C.B. 2. Removal of Front Panel Unit
9 MAIN (2) P.C.B. a. Remove 2 knobs. (Fig. 1)
0 DIGITAL P.C.B. b. Remove screw (4) and then remove the support top. 4
A FUNCTION (9) P.C.B. (Fig. 1)
B FUNCTION (1) P.C.B c. Remove 6 screws (5). (Fig. 1) 5
C Tuner (U, C, R, T, K, A, G, E, F, L, J models) d. Remove the front panel unit. (Fig. 1)
D FUNCTION (5) P.C.B. (B model)
E OPERATION (2) P.C.B. 3. Removal of Sub Chassis Unit
F OPERATION (3) P.C.B. a. Remove 2 push rivets (6). (Fig. 1) 6
G OPERATION (1) P.C.B. b. Remove the plate side L and plate side R. (Fig. 1)
c. Remove 2 screws (7). (Fig. 1)
H OPERATION (4) P.C.B.
d. Remove CB30, CB46, CB63, CB201, CB221 and 7
I OPERATION (5) P.C.B.
CB422. (Fig. 1)
• Front view e. Remove the sub chassis unit. (Fig. 1)

Top cover 2

1 3

E F G H I

Plate side L
1
CB221
CB201

Support top
CB422
4 CB46
5
7 CB63

CB30

5 6
7

Sub chassis unit

Plate side R
Knob Front panel unit

14 Fig. 1
 RX-V663/HTR-6160/DSP-AX763

4. Removal of FUNCTION (1) P.C.B. RX-V663 (U, C models)

a. Remove 2 push rivets (8). (Fig. 2) 8 HTR-6160 (U, C models)
b. Remove 10 screws (RX-V663: U, C, R, T, K, A, G, E, F, 9 RX-V663 (U, C models)
HTR-6160 (U model)
L models / HTR-6160: U, F models) / 9 screws (HTR-
9 A
6160: C model / DSP-AX763: B model) (9). (Fig. 3)
c. Remove CB205, CB206, CB231, CB232, CB242 (C,
R, T, K, A, G, E, F, L models), CB243 (DSP-AX763: B
model) and CB302. (Fig. 2)
d. Remove the FUNCTION (1) P.C.B.. (Fig. 2)

5. Removal of DIGITAL P.C.B.

a. Remove 2 screws (0). (Fig. 2) 0
b. Remove 9 screws (A). (Fig. 3) A
c. Remove CB31-33, CB62 and CB80-82. (Fig. 2)
d. Remove the DIGITAL P.C.B.. (Fig. 2)

FUNCTION (1) P.C.B.

CB232
CB231 CB206
8 RX-V663 (R, T, K, A, G, E, F, L models)
HTR-6160 (F model)
CB205
CB242 (C, R, T, K, A, G, E, F, L, J models) DSP-AX763 (B, J models)
CB243 (B model) RX-V663 (R, T, K, A, G, E, F, L models)
HTR-6160 (F models)
CB80
CB33 9 A
CB81
CB31
CB32
CB82 CB38
0 (J model) DIGITAL P.C.B.
CB302 CB62

Fig. 3

Fig. 2

15
 RX-V663/HTR-6160/DSP-AX763

6. Removal of VIDEO (1) and (2) P.C.B.s 7. Removal of AM/FM Tuner (U, C, R, T, K, A, G, E,
a. Remove 2 screws (B) and then remove the FUNC- B F, L models) E
TION (6) P.C.B. which is connected directly to the a. Remove 2 screws (E). (Fig. 6)
VIDEO (1) and (2) P.C.B.s with board to board con- b. Remove the AM/FM tuner. (Fig. 6)
nectors. (Fig. 4)
b. Remove 4 screws (C). (Fig. 5)
c. Remove CB303. (Fig. 4) C
d. Remove the VIDEO (1) P.C.B.. (Fig. 4)
E
e. Remove 3 screws (D). (Fig. 5)
f. Remove the VIDEO (2) P.C.B.. (Fig. 4) D
AM/FM tuner

FUNCTION (6) P.C.B.

VIDEO (1) P.C.B.

CB303

B
Fig. 6

8. Removal of FUNCTION (5) P.C.B. (B model)

a. Remove screw (F). (Fig. 7)
b. Remove the FUNCTION (5) P.C.B.. (Fig. 7)

F
VIDEO (2) P.C.B.

Fig. 4

(U, C, R, T, K, A, B, G, E, F, L models) (J model)

C D FUNCTION (5) P.C.B.

Fig. 7

Fig. 5

16
 RX-V663/HTR-6160/DSP-AX763

9. Removal of Amp Unit

a. Remove 2 screws (G), screw (H), 2 screws (I) and G H I J
screw (J). (Fig. 8)
b. Remove 6 screws (K). (Fig. 8) K
c. Remove CB100, CB101 and CB251. (Fig. 8)
d. Remove the MAIN (1) and (2) P.C.B.s together with
heat sink. (Fig. 8)

CB251

CB100
G
CB101

K
J

H
Heat sink

RX-V663/HTR-6160/
MAIN (1) P.C.B.

DSP-AX763
Fig. 8

17
 RX-V663/HTR-6160/DSP-AX763

When checking the P.C.B.:

• Put the rubber sheet and cloth over the equipment.
Then place the FUNCTION(1) P.C.B. upside down on
the cloth and check it. (Fig. 9)
• Reconnect all cables (connectors) that have been
disconnected.
• When connecting the flexible flat cable, be careful
with polarity.
• Be sure to use the extension cable for servicing for
the following section. (Fig. 9)
FUNCTION (1) P.C.B. CB205–DIGITAL P.C.B. CB61:
MF125400 (25P, 400mm, P=1.25)
• In this unit, the ground of P.C.B.s shown below is
connected to the rear panel and chassis.
When FUNCTION (1) P.C.B. is removed from the
rear panel and chassis, connect the ground point to
the rear panel or chassis, using a ground lead or the
like. (Fig. 9)
FUNCTION (1) P.C.B.: PJ201 (PHONO)
FUNCTION (1) P.C.B.: PJ203 (DVD)
FUNCTION (1) P.C.B.: PJ209 (PRE OUT)
FUNCTION (1) P.C.B.: PJ294 (SUBWOOFER2)

Ground point Ground point

FUNCTION (1) P.C.B.

PJ294

Ground lead
PJ209 PJ203 PJ201
(R, T, K, A, B, G, E, F,
L, J models)
Ground lead
RX-V663/HTR-6160/
DSP-AX763

Rubber sheet and cloth

FUNCTION (1) P.C.B.

CB205

CB61 Rear panel

Ground lead

MF125400

Tuner DIGITAL P.C.B.

18 Fig. 9
 RX-V663/HTR-6160/DSP-AX763

When checking the P.C.B.: Ground point

DIGITAL P.C.B. Ground point
• Put the rubber sheet and cloth over the equipment.
PJ41 ST100
Then place the FUNCTION (1) and DIGITAL P.C.B.s
upside down on the cloth and check it. (Fig. 10) FUNCTION (1) P.C.B.
• Reconnect all cables (connectors) that have been
disconnected. PJ294
• When connecting the flexible flat cable, be careful
with polarity.
• Be sure to use the extension cable for servicing for PJ209 PJ203 PJ201
(R, T, K, A,
the following section. (Fig. 10)
B, G, E, F,
FUNCTION (1) P.C.B. CB205–DIGITAL P.C.B. CB61: L, J models)
MF125400 (25P, 400mm, P=1.25)
DIGITAL P.C.B. CB80–VIDEO (1) P.C.B. CB305: Ground lead
MF126500 (26P, 500mm, P=1.25)
DIGITAL P.C.B. CB81–VIDEO (2) P.C.B. CB302:
MF116400 (16P, 400mm, P=1.25) Ground lead
• In this unit, the ground of P.C.B.s shown below is
connected to the rear panel and chassis.
When FUNCTION (1) P.C.B. is removed from the Rubber sheet and cloth
rear panel and chassis, connect the ground point to CB80
the rear panel or chassis, using a ground lead or the CB81
like. (Fig. 10)
FUNCTION (1) P.C.B.: PJ201 (PHONO) MF126500 CB305
VIDEO (1) P.C.B.
FUNCTION (1) P.C.B.: PJ203 (DVD) CB302
FUNCTION (1) P.C.B.: PJ209 (PRE OUT)
FUNCTION (1) P.C.B.
FUNCTION (1) P.C.B.: PJ294 (SUBWOOFER2) G100
DIGITAL P.C.B. : ST100 CB205
CB61
DIGITAL P.C.B. : PJ41 (DVD COAXIAL INPUT)
DIGITAL P.C.B. : G100, G300 DIGITAL P.C.B.
DIGITAL P.C.B. : ST41 (XM) (U, C models) MF116400
VIDEO (2) P.C.B.

Ground lead
Rear panel
Ground lead
G300

MF125400

Tuner

Fig. 10

19
 RX-V663/HTR-6160/DSP-AX763

■ UPDATING FIRMWARE /
Note) Updating the firmware restores all the sound field
parameters, system memory and tuner preset-
ting, etc. to the original factory settings. ● Operation Procedures
1. Connect this unit and DVD/CD player as shown
below. (Fig. 1)
When replacing the following parts, be sure to write the
latest firmware.
Example of OPTICAL jack /
P.C.B. ass’y DIGITAL P.C.B.
This unit
IC30 (Main microprocessor) of DIGITAL P.C.B.
IC51 (TI (DSP) flash ROM) of DIGITAL P.C.B.
There are 2 ways to write the firmware. DVD/CD player
• Writing method using the CD:
Transferring data using CD through digital inputs.
* When IC30 of DIGITAL P.C.B. is replaced, it is not
possible to write the firmware by using the CD.
• Writing method using PC (RS232C):
Transferring data using PC through serial port
(RS232C).

Writing method using the CD

● Required Tools Optical cable

• DVD or CD player (with DIGITAL OUTPUT (OP-

TICAL or COAXIAL) jack)
• Optical cable (when OPTICAL jack is used)
• Digital audio pin cable (when COAXIAL jack is
used) Example of COAXIAL jack /
• Firmware CD
This unit
* To make the firmware CD, download the latest
firmware from the specified download source
to PC.
DVD/CD player

Digital audio pin cable

Fig. 1

20
 RX-V663/HTR-6160/DSP-AX763

2. While pressing the “TONE CONTROL” key of this

unit, connect the power cable of this unit to the AC
outlet. (Fig. 2)
The FIRMWARE UPDATE mode is activated and
“CDDA Upgrader” is displayed. (Fig. 2)

"TONE CONTROL" key

CDDA Upgrader

Fig. 2

3. Connect the power cable of DVD/CD player to the

AC outlet.
4. Press the “STANDBY/ON” key of the DVD/CD
player.
5. Press the “EJECT” key of the DVD/CD player to
open the disc tray.
6. Put the firmware CD on the disc tray and close the
disc tray.
7. Press the “PLAY” key of the DVD/CD player.
Then writing of the firmware is started. (Fig. 3)

RX-V663/HTR-6160/
8. When writing of the firmware is completed, “Up-

DSP-AX763
date Success”, “Please...” and “Power off!!” are
displayed repeatedly. (Fig. 3)

Writing is started. / Writing is completed. /

Address:XXXXXX Update Success

XXXXXX: Address information of the received data /

Please...

Power off!!

Fig. 3

21
 RX-V663/HTR-6160/DSP-AX763

* When the version of the firmware to be writ-

ten is the same as the one existing in this unit,
“Same Version”, “Please...” and “Power off!!”
are displayed repeatedly. (Upgrading is not
necessary.)
If the display remains unchanged for more
than 10 seconds after starting the firmware
CD play procedure, perform the firmware CD
play procedure again from the beginning.
If “FILE CORRUPTED” is displayed after
“Address:XXXXXX”, make sure that the writ-
ten data is not corrupted and perform Steps 1
to 8 of “Operation Procedures” again.
If “Upgrade Failed” is displayed, perform
Steps 1 to 8 of “Operation Procedures” again.
9. Press the “STOP” key of the DVD/CD player.
10. Press the “EJECT” key of the DVD/CD player to
open the disc tray.
11. Remove the firmware CD from the disc tray and
close the disc tray.
12. Turn off the power of the DVD/CD player and dis-
connect the power cable from the AC outlet.
13. Turn off the power by pressing the “MAIN ZONE
ON/OFF” (RX-V663 / THR-6160: U, F models) /
“STANDBY/ON” (HTR-6160: C model / DSP-
AX763) key of this unit.

● Initializing of this unit

* After updating the firmware, be sure to initialize
this unit.
1. Connect the power cable of this unit to the AC
outlet.
RX-V663/HTR-6160/

2. Press the “MAIN ZONE ON/OFF” (RX-V663 / HTR-

DSP-AX763

6160: U, F models) / “STANDBY/ON” (HTR-6160: C

model / DSP-AX763) key while simultaneously
pressing the “STRAIGHT” and “AUDIO SELECT”
keys. (Fig. 4)
Then the self-diagnostic function is activated.
3. Select the self-diagnostic function menu “23.
FACTORY PRESET”.
4. Select the “PRESET RSRV”.

"MAIN ZONE ON/OFF" key

(RX-V663 / HTR-6160: U, F models)
"STANDBY/ON" key
(HTR-6160: C model /
DSP-AX763) "STRAIGHT" key "AUDIO SELECT" key

PRESET INHIBIT (Initialization inhibited) / PRESET RESERVED (Initialization reserved) /

23.PRESET INHI 23.PRESET RSRV

Fig. 4
22
 RX-V663/HTR-6160/DSP-AX763

5. Turn off the power of this unit and disconnect the

power cable from the AC outlet.

● Confirmation of firmware version and checksum

To confirm that the firmware is updated successfully,

check the firmware version and checksum value by
using the self-diagnostic function.
For more information, refer to “SELF-DIAGNOSTIC
FUNCTION”.
1. Reconnect the power cable of this unit to the AC
outlet.
2. Press the “MAIN ZONE ON/OFF” (RX-V663 / HTR-
6160: U, F models) / “STANDBY/ON” (HTR-6160: C
model / DSP-AX763: B model) key while simulta-
neously pressing the “STRAIGHT” and “AUDIO SE-
LECT” keys. (Fig. 5)
Then the self-diagnostic function is activated.
3. Select the self-diagnostic function menu “24-1.
Version”.
Confirm the displayed firmware version is the
same as the written firmware version. (Fig. 5)

"MAIN ZONE ON/OFF" key

RX-V663/HTR-6160/
(RX-V663 / HTR-6160: U, F models)
"STANDBY/ON" key

DSP-AX763
(HTR-6160: C model /
DSP-AX763) "STRAIGHT" key "AUDIO SELECT" key

Ver: B047U
Fig. 5

4. Select the self-diagnostic function menu “24-2. All

checksum”.
Confirm the displayed checksum is the same as
the written firmware checksum. (Fig. 5)
(The checksum value is found where download-
ing is specified to.)

Sum: 4913
Fig. 6

* When the displayed firmware version and checksum

are different from written firmware version and
checksum, follow the steps from 1 to 13 of “Operation
Procedures” again.

23
 RX-V663/HTR-6160/DSP-AX763

Writing method using PC (RS232C)

● Required Tools
• Windows 2000/XP, PC with a serial port (RS232C)
• Firmware downloader program
For microprocessor:
DSP_FLASHER_v3.0_M16C80.exe
For DSP (TI flash ROM):
DSP_FLASHER Ver2.7.exe
• Firmware
For microprocessor:
VX63xxxx.mot
For DSP (TI flash ROM):
Vx63_data1_verxxxxxr.hex
• RS232C cross cable “D-sub 9 pin female”
(Specifications)
Pin No.2 RxD Pin No.2 RxD
Pin No.3 TxD Pin No.3 TxD Pin No.2 RxD Pin No.2 RxD
Pin No.5 GND Pin No.5 GND Pin No.3 TxD Pin No.3 TxD
Pin No.7 RTS Pin No.7 RTS Pin No.5 GND Pin No.5 GND
Pin No.8 CTS Pin No.8 CTS Pin No.7 RTS Pin No.7 RTS
• RS232C conversion adapter (Including flexible Pin No.8 CTS Pin No.8 CTS
flat cable 9P, 300mm) / Part no.: AAX77610

● Preparation and precautions before starting

the operation
• Download firmware upgrading program and firm-
ware from the specified source to the same folder
of the PC.
• Prepare the above specified RS232C cross cable.
• While writing, keep the other application software
on the PC closed.
RX-V663/HTR-6160/

It is also recommended to keep the software on

the task tray closed as well.
DSP-AX763

● Operation Procedures

Writing to the microprocessor

• Writing firmware
1. Turn off the power of this unit and disconnect the
power cable from the AC outlet.

24
 RX-V663/HTR-6160/DSP-AX763

2. Set the switch (SW301) of RS232C conversion

adapter to the “FLASH UCOM” side. (Fig. 1)
3. Connect the writing port of this unit to the serial port
(RS232C) of the PC with RS232C cross cable,
RS232C conversion adapter and flexible flat cable
as shown below. (Fig. 1)

PC Rear panel

Serial port (RS232C) /

RS232C conversion adapter / Writing port /

RS232C cross cable / Flexible flat cable (9P) /

SW301
FLASH
UCOM OTHER

Fig. 1

4. Start up “DSP_FLASHER_v3.0_M16C80.exe”.
“DSP FLASHER_V3.0” is displayed. (Fig. 2)
5. Click [...]. (Fig. 2)

RX-V663/HTR-6160/
DSP-AX763
Select “VX63xxx.mot (Fig. 2)

J model
U, C, R, T, K, A, B, G, E, F, L models

Fig. 2 25
 RX-V663/HTR-6160/DSP-AX763

6. Reconnect the power cable of this unit to the AC

outlet.
7. Click [E.P.] to start writing. (Fig. 3)

8. When writing is completed, “Program Finished!” is

displayed. (Fig. 3)
Click [OK]. (Fig. 3)

9. Click [EXIT] to end “DSP_FLASHER_v3.0_M16

C80.exe”. (Fig. 3)
RX-V663/HTR-6160/
DSP-AX763

Writing completed /

Writing /

Fig. 3

26
 RX-V663/HTR-6160/DSP-AX763

10. Disconnect the power cable of this unit from the

AC outlet.
11. Disconnect the RS232C cross cable, RS232C
conversion adapter and flexible flat cable.

• Initializing of this unit

* After updating the firmware, be sure to initialize
this unit.
1. Connect the power cable of this unit to the AC
outlet.
2. Press the “MAIN ZONE ON/OFF” (RX-V663 / HTR-
6160: U, F models) / “STANDBY/ON” (HTR-6160: C
model / DSP-AX763) key while simultaneously
pressing the “STRAIGHT” and “AUDIO SELECT”
keys. (Fig. 4)
Then the self-diagnostic function is activated.
3. Select the self-diagnostic function menu “23.
FACTORY PRESET”.
4. Select the “PRESET RSRV”.

"MAIN ZONE ON/OFF" key

(RX-V663 / HTR-6160: U, F models)
"STANDBY/ON" key

RX-V663/HTR-6160/
(HTR-6160: C model /
DSP-AX763)

DSP-AX763
"STRAIGHT" key "AUDIO SELECT" key

PRESET INHIBIT (Initialization inhibited) / PRESET RESERVED (Initialization reserved) /

23.PRESET INHI 23.PRESET RSRV

Fig. 4

• Confirmation of firmware version and checksum

To confirm that the firmware is updated successfully,

check the firmware version and checksum value by
using the self-diagnostic function.
For more information, refer to “SELF-DIAGNOSTIC
FUNCTION”.

27
 RX-V663/HTR-6160/DSP-AX763

1. Reconnect the power cable of this unit to the AC

outlet.
2. Press the “MAIN ZONE ON/OFF” (RX-V663 / HTR-
6160: U, F models) / “STANDBY/ON” (HTR-6160: C
model / DSP-AX763: B model) key while simulta-
neously pressing the “STRAIGHT” and “AUDIO SE-
LECT” keys. (Fig. 5)
Then the self-diagnostic function is activated.
3. Select the self-diagnostic function menu “24-1.
Version”.
Confirm the displayed firmware version is the
same as the written firmware version. (Fig. 5)

"MAIN ZONE ON/OFF" key

(RX-V663 / HTR-6160: U, F models)
"STANDBY/ON" key
(HTR-6160: C model /
DSP-AX763) "STRAIGHT" key "AUDIO SELECT" key

Example /

VX63B047.mot Ver: B047V

Fig. 5
RX-V663/HTR-6160/
DSP-AX763

4. Select the self-diagnostic function menu “24-2. All

checksum”.
Confirm the displayed checksum is the same as
the written firmware checksum. (Fig. 5)
(The checksum value is found where download-
ing is specified to.)

Example /

Checksum: 4913 Sum: 4913

Fig. 6

* When the displayed firmware version and checksum

are different from written firmware version and
checksum, follow the steps from 1 to 11 of “Operation
Procedures” again.

28
 RX-V663/HTR-6160/DSP-AX763

Writing to DSP

• Writing firmware
1. Turn off the power of this unit and disconnect the
power cable from the AC outlet.
2. Set the switch (SW301) of RS232C conversion
adapter to the “OTHER” side. (Fig. 1)
3. Connect the writing port of this unit to the serial port
(RS232C) of the PC with RS232C cross cable,
RS232C conversion adapter and flexible flat cable
as shown below. (Fig. 1)

PC Rear panel

Serial port (RS232C) /

RS232C conversion adapter / Writing port /

RS232C cross cable / Flexible flat cable (9P) /

SW301
FLASH
UCOM OTHER

Fig. 1

RX-V663/HTR-6160/
4. Start up “DSP_FLASHER Ver2.7.exe”.

DSP-AX763
“DSP FLASHER_V2.70” is displayed. (Fig. 2)
5. Click [Vx61 DSP]. (Fig. 2)

Fig. 2

29
 RX-V663/HTR-6160/DSP-AX763

6. Click [...]. (Fig. 3)

Select “Vx63_data1_verxxxxxr.hex”. (Fig. 3)

Fig. 3

7. Click [RDY]. (Fig. 4)

RX-V663/HTR-6160/
DSP-AX763

Fig. 4

30
 RX-V663/HTR-6160/DSP-AX763

8. Connect the power cable of this unit to the AC

outlet while pressing the “AUDIO SELECT” key.
(Fig. 5)
Writing is started automatically. (Fig. 5)

"AUDIO SELECT" key

RX-V663/HTR-6160/
DSP-AX763
Writing /

Fig. 5

31
 RX-V663/HTR-6160/DSP-AX763

9. When writing is completed, “Vx61 DSP Flash fin-

ished!” is displayed. (Fig. 6)
10. Click [EXIT] to end “DSP_FLASHER Ver2.7.exe”.
(Fig. 6)

When writing is completed, “Vx61 DSP Flash finished!” is displayed.

Fig. 6

11. Disconnect the power cable of this unit from the

RX-V663/HTR-6160/

AC outlet.
DSP-AX763

12. Disconnect the RS232C cross cable, RS232C

conversion adapter and flexible flat cable.

32
 RX-V663/HTR-6160/DSP-AX763

• Initializing of the main unit

* After updating the firmware, be sure to initialize
this unit.
1. Connect the power cable of this unit to the AC
outlet.
2. Press the “MAIN ZONE ON/OFF” (RX-V663 / HTR-
6160: U, F models) / “STANDBY/ON” (HTR-6160: C
model / DSP-AX763: B model) key while simulta-
neously pressing the “STRAIGHT” and “AUDIO SE-
LECT” keys. (Fig. 7)
Then the self-diagnostic function is activated.
3. Select the self-diagnostic function menu “23.
FACTORY PRESET”.
4. Select the “PRESET RSRV”.

"MAIN ZONE ON/OFF" key

(RX-V663 / HTR-6160: U, F models)
"STANDBY/ON" key
(HTR-6160: C model /
DSP-AX763) "STRAIGHT" key "AUDIO SELECT" key

PRESET INHIBIT (Initialization inhibited) / PRESET RESERVED (Initialization reserved) /

23.PRESET INHI 23.PRESET RSRV

RX-V663/HTR-6160/
Fig. 7

DSP-AX763
• Confirmation of firmware version and checksum

To confirm that the firmware is updated successfully,

check the firmware version and checksum value by
using the self-diagnostic function.
For more information, refer to “SELF-DIAGNOSTIC
FUNCTION”.

33
 RX-V663/HTR-6160/DSP-AX763

1. Connect the power cable of this unit to the AC

outlet.
2. Press the “MAIN ZONE ON/OFF” (RX-V663 / HTR-
6160: U, F models) / “STANDBY/ON” (HTR-6160: C
model / DSP-AX763: B model) key while simulta-
neously pressing the “STRAIGHT” and “AUDIO SE-
LECT” keys. (Fig. 8)
Then the self-diagnostic function is activated.
3. Select the self-diagnostic function menu “24-3. TI
FLASH version”.
Confirm the displayed firmware version is the
same as the written firmware version. (Fig. 8)

"MAIN ZONE ON/OFF" key

(RX-V663 / HTR-6160: U, F models)
"STANDBY/ON" key
(HTR-6160: C model /
DSP-AX763) "STRAIGHT" key "AUDIO SELECT" key

Example /
TiVer:04.05r2

Fig. 8
RX-V663/HTR-6160/
DSP-AX763

4. Select the self-diagnostic function menu “24-4. TI

FLASH checksum”.
Confirm the displayed checksum is the same as
the written firmware checksum. (Fig. 9)
(The checksum value is found where download-
ing is specified to.)

Example /
TiSum:021D2136

Fig. 9

* When the displayed firmware version and checksum

are different from written firmware version and
checksum, follow the steps from 1 to 12 of “Operation
Procedures” again.

34
 RX-V663/HTR-6160/DSP-AX763

■ SELF-DIAGNOSTIC FUNCTION
This unit has self diagnosis functions that are intended for
inspection, measurement and location of faulty point.
There are 24 main menu items, each of which has sub-
menu items.
Listed in the table below are menu items and sub-menu
items.
Note that not all menu items listed will apply to the models
covered in this service manual.
No. Main menu Sub-menu No. Main menu Sub-menu
1 BYPASS 1. ANALOG BYPASS 12 SIRIUS (U, C models) 1. SIRIUS : OK (NG)
2. DSP BYPASS 2. SR : XX XX XX
2 RAM THR 1. RAM MARGIN 3. SSP : (SIRIUS #0 version)
2. RAM FULL BIT 4. MAC : (SIRIUS #1 version)
3 HDMI AUDIO 1. SPDIF 5. ADP : (SIRIUS #2 version)
2. Multi 6. PRDID : (Product ID)
3. DSD 7. SEQID : (Sequence ID)
4 SPEAKERS SET 1. FRONT : SML 0dB 13 HD RADIO (U model) 1. HD CPU V : XXXXX
2. CENTER : NONE 2. D : XXXXX
3. LFE/B : FRONT 14 DOCK 1. DOCK : XXXXX
4. PRESENCE Mix-P 2. BT V : – – – – – – – –
5. PRESENCE Mix-F 15 HDMI INFORMATION 1. MN : XXXXXXX
6. Zone2 Amp ON 2. PI : 312X
7. Bi-AMP 3. VN : YAMAHA
8. TONE : MAX 16 HDMI SELECT 1. HDMI NONE
9. TONE : MIN 2. HDMI IN 1
5 XCH-INPUT 1. 6ch INPUT 6ohms 3. HDMI IN 2
2. 8ch INPUT 6ohms 4. HDMI IN 3
3. 6ch INPUT 8ohms 5. HDMI UPCONV.
4. 8ch INPUT 8ohms 6. HDMI UP THR
5. LIMIT 17 IF STATUS 1. DSP STATUS (5 Byte)
6 MIC CHECK 1. MIC CHECK 18 DSP BUS CHECK 1. TI BUS :
7 FL/OSD CHECK 1. VFD CHECK 19 RESERVED
2. VFD DISP OFF / MONITOR MUTE 20 PROTECTION HISTORY 1. HISTORY 1
3. VFD DISP ALL / Conponent MUTE 2. HISTORY 2
4. VFD DIMMER / OSD CHARACTERS PATTERN 3. HISTORY 3
5. CHECK PATTERN / OSD CHARACTERS PATTERN 4. HISTORY 4
8 MANUAL TEST 1. TEST ALL 21 RESERVED
9 A/D DATA CHECK 1. PS1, PS2 22 UPDATE (Not applied to these models. / 1. TI FLASH BOOT
2. DC, TH ) 2. CEC UPDATE
3. IMP, PL 23 FACTORY PRESET 1. PRESET INHI
4. DST, DK 2. PRESET RSRV
5. K0, K1 24 ROM VER./SUM/PORT 1. VERSION DISP
10 VIDEO CHECK 1. I2C : XXXXXXXX 2. SUM ALL / PROGRAM
2. DIGITAL COMPONENT 3. TI FLASH VERSION (1 Byte)
3. DIGITAL CVBS 4. TI FLASH SUM (4 Byte)
4. DIGITAL Y/C 5. CEC VERSION
5. ANALOG BYPASS 6. XM VERSION (U, C models)
6. TEST PATTERN 7. SIRIUS VERSION (U, C models)
7. VIDEO INFORMATION 8. XX XXX X XXX
11 XM STATUS (U, C models) 1. 1k -1dB/44kHz
2. 1k -61dB/44kHz
3. MUTE/44kHz
4. XM TONE/44kHz
5. ISO TONE/44kHz
6. 1k -1dB/32kHz
7. 1k -61dB/32kHz
8. MUTE/32kHz
9. XM TONE/32kHz
10. ISO TONE/32kHz
11. BUS POWER : OFF

35
 RX-V663/HTR-6160/DSP-AX763

• Starting Self-Diagnostic Function • Canceling Self-Diagnostic Function

Press the “MAIN ZONE ON/OFF” (RX-V663 / HTR- 1. Before canceling self-diagnostic function, execute
6160: U, F models) / “STANDBY/ON” (HTR-6160: C setting for FACTORY PRESET of main menu No.
model / DSP-AX763) key while simultaneously press- 23 (Memory initialization inhibited or Memory ini-
ing those two keys of this unit as indicated in the figure tialized).
below. * In order to keep the user memory stored, be
sure to select PRESET INHIBITED (Memory ini-
Keys of this unit / tialization inhibited).
2. Turn off the power by pressing the “MAIN ZONE
RX-V663 / HTR-6160 (U, F models) ON/OFF” (RX-V663 / HTR-6160: U, F models) /
“STANDBY/ON” (HTR-6160: C model / DSP-
AX763: B, J models) key of this unit.

• Display provided when Self-Diagnos-

HTR-6160 (C model) /
DSP-AX763 tic Function started
Turn on the power while pressing these keys. / On the FL display of this unit, an opening message
(including the version and the protection history) ap-
pears for a few seconds followed by the main menu
display (1. ANALOG BYPASS).

When there is no history of protection function:

Opening message / Main menu display /

When there is no protection history

• Starting Self-Diagnostic Function in
After a few seconds /
the protection cancel mode
If the protection function works and causes hindrance
to trouble diagnosis, cancel the protection function as NO PROTECT 1.ANALOG BYPAS
described below, and it will be possible to enter the
self-diagnostic function mode. (The protection func-
tions other than the excess current detect function will
be disabled.)

Press the “MAIN ZONE ON/OFF” (RX-V663 / HTR-

6160: U, F models) / “STANDBY/ON” (HTR-6160: C
model / DSP-AX763) key while simultaneously press-
ing those two keys indicated in the figure above. At
this time, keep pressing those two keys for 3 seconds
or longer.
In this mode, the [SLEEP] segment of the FL display
of this unit flashes to indicate that the mode is self-
diagnostic function mode with the protection functions
disabled.

CAUTION!
Using this product with the protection function dis-
abled may cause damage to this unit. Use special
care for this point when using this mode.

36
 RX-V663/HTR-6160/DSP-AX763

When there is a history of protection function:

When there is a history of protection function due
to excess current

I PROTECT

Cause: An excessive current flowed through the

power amplifier.
Supplementary information:
As current of the power amplifier is detected,
the abnormal channel can be identified by
checking the current detect transistor.
Turning on the power without correcting the
abnormality will cause the protection func-
tion to work immediately and the power sup-
ply will instantly be shut off.

Note)
• Applying the power to this unit without correcting
the abnormality can be dangerous and cause ad-
ditional circuit damage. To avoid this, if protection
function has been activated 3 times continuously,
the power will not turn on even when the “MAS-
TER ON/OFF” (RX-V663 / HTR-6160: F model) /
“STANDBY/ON” (HTR-6160: U, C models / DSP-
AX763) key is pressed. In order to turn on the
power again, disconnect the power cable of this
unit from the AC outlet once and then reconnect it
again.
• The output transistors in each power amplifier
should be checked for damage before applying
power to this unit.
• Power amplifier current should be monitored by
measuring DC voltage across the emitter resistors
for each channel.

RX-V663/HTR-6160/
DSP-AX763
When there is a history of protection function due
to abnormal DC output

DC PRT :xxx G

Cause: DC output of the power amplifier is abnormal.

Supplementary information:
The protection function worked due to a DC
voltage appearing at the speaker terminal.
A cause could be a defect in the amplifier.
If the power is turned on with the abnormality
unsolved, the protection function works in 3
seconds to turn off the power.

37
 RX-V663/HTR-6160/DSP-AX763

When there is a history of protection function due

to abnormal voltage in the power supply section

PS1 PRT:xxx or PS2 PRT:xxx

Cause: The voltage in the power supply section is

abnormal.
Supplementary information:
The protection function worked due to a de-
fect or overload in the power supply.
If the power is turned on with the abnormality
unsolved, the protection function works in 1
second to turn off the power.

When there is a history of protection function due

to excessive heat sink temperature

TMP PRT:xxx G

Cause: The temperature of the heat sink is excessive.

Supplementary information:
The protection function worked due to the
temperature limit being exceeded.
Causes could be poor ventilation or a defect
related to the thermal sensor.

If the power is turned on with the abnormality unsolved,

the protection function works in 1 second to turn off the
power.

For detection of each protection function, refer to main

menu described later.

History of protection function

RX-V663/HTR-6160/

When the protection function has worked, its history

DSP-AX763

is stored in memory with a backup.

Even if no abnormality is noted while servicing this
unit, an abnormality which has occurred previously
can be defined as long as the backup data has been
stored.
The history of the protection function is cleared
when self-diagnostic function is cancelled by select-
ing PRESET RESERVED (Memory initialized) of main
menu No. 23 or when the backup data is erased.

• Display during menu operation

The function at work is indicated on the FL indicator of
this unit.
The contents displayed during the function operation
are described later in the “Details of self-diagnostic
function menu” section.

38
 RX-V663/HTR-6160/DSP-AX763

• Operation procedure of Main menu

and Sub-menu
There are 24 main menu items, each them having
sub-menu items.
Main menu selection:
Select the main menu using “PROGRAM” knob.
Sub-menu selection:
Select the sub-menu using “SCENE 2” (forward) /
“SCENE 1” (reverse) keys or “PRESET/TUNING >”
(forward) / “PRESET/TUNING <” (reverse) keys (U, C,
R, T, K, A, G, E, F, L models).

Keys of this unit /

Reverse Forward U, C, R, T, K, A, G,
E, F, L, J models
Sub-menu selection
Reverse Forward

Main menu selection Reverse Forward

• Functions in Self-Diagnostic Function

mode
In addition to the self-diagnostic function menu items,
functions as listed below are available.
• Power on/off
• Master volume
• Muting
• Speaker relay control of A and B

RX-V663/HTR-6160/
• Input selection

DSP-AX763
• Audio select
• Tone control
* Functions related to the tuner and the set menu are
not available.

• Initial settings when starting Self-Di-

agnostic Function
The following are initial settings when starting self-di-
agnostic function.
• Master volume: -20 dB
• Input: DVD (MULTI CHANNEL INPUT OFF)
• Effect level: 0 dB
• Main menu: 1. ANALOG BYPASS

When self-diagnostic function is canceled, these set-

tings are restored to those before starting self-diag-
nostic function.

39
 RX-V663/HTR-6160/DSP-AX763

• Details of Self-Diagnostic Function menu

1. BYPASS
Using the sub-menu, it is possible to select ANALOG
BYPASS output or DSP BYPASS output.

ANALOG BYPASS
The analog input audio signal is output to FRONT L/R
by PURE DIRECT.

1.ANALOG BYPAS
INPUT: DVD ANALOG
SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz
SPEAKER OUT SUBWOOFER
Input level Volume
FRONT L/R CENTER SURROUND L/R SURROUND BACK L/R OUTPUT
Both ch, -20 dBm +6.0 dB +12.0 dBm -∞ -∞ -∞ -∞

DSP BYPASS
The digital input audio signal is output to FRONT L/R
by PURE DIRECT.

1.DSP BYPASS
INPUT: DVD ANALOG
SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz
SPEAKER OUT SUBWOOFER
Input level Volume
FRONT L/R CENTER SURROUND L/R SURROUND BACK L/R OUTPUT
Both ch, -20 dBm +6.0 dB +12.0 dBm -∞ -∞ -∞ -∞

ANALOG BYPASS (U, C) XMDT

FL / FR

DIR
LC89057 DSP
(DECODE)
C / SW
(POST PROCESSING)
TI D70Y
RX-V663/HTR-6160/

SL / SR
DSP-AX763

A/D SBL / SBR

PCM1803

DRAM ROM

(Shaded items not used in this example)

DSP BYPASS (U, C) XMDT

FL / FR

DIR
LC89057 DSP
(DECODE)
C / SW
(POST PROCESSING)
TI D70Y
SL / SR

A/D SBL / SBR

PCM1803

DRAM ROM

(Shaded items not used in this example)

40
 RX-V663/HTR-6160/DSP-AX763

2. RAM THROUGH
Using the sub-menu, it is possible to select MARGIN
output or FULL BIT output.

RAM MARGIN
The signal is output including the head margin.

2.RAM MARGIN

FRONT L/R CENTER SURROUND L/R SURROUND BACK L/R SUBWOOFER

+9.0 dB +13.5 dB +9.0 dB +7.5 dB +21.0 dB

INPUT: DVD ANALOG

SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz
SPEAKER OUT SUBWOOFER
Input level Volume
FRONT L/R CENTER SURROUND L/R SURROUND BACK L/R OUTPUT
Both ch, -20 dBm +6.0 dB +12.0 dBm +12.0 dBm +12.0 dBm +12.0 dBm -7.0 dBm

RAM FULL BIT

The signal is output in digital full bit without including
the head margin.
The SUBWOOFER signal is output but not in digital
full bit.

2.RAM FULL BIT

FRONT L/R CENTER SURROUND L/R SURROUND BACK L/R SUBWOOFER

0 dB 0 dB 0 dB 0 dB +21.0 dB

INPUT: DVD ANALOG

SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz
SPEAKER OUT SUBWOOFER
Input level Volume
FRONT L/R CENTER SURROUND L/R SURROUND BACK L/R OUTPUT
Both ch, -20 dBm +6.0 dB +12.0 dBm +12.0 dBm +12.0 dBm +12.0 dBm -7.0 dBm

RX-V663/HTR-6160/
DSP-AX763
(U, C) XMDT

FL / FR

DIR
LC89057 DSP
(DECODE)
C / SW
(POST PROCESSING)
TI D70Y
SL / SR

A/D SBL / SBR

PCM1803

DRAM ROM

(Shaded items not used in this example)

When input source is stereo, signal is assigned as below.

Front L → Center / Surround L / Surround Back L, R

Front R → Surround R
Front L +10 dB → SWFR

41
 RX-V663/HTR-6160/DSP-AX763

3. HDMI AUDIO
The audio signals input to HDMI IN are selected by
the sub-menu and output.
* When selecting “DSD”, be sure to connect an HDMI
unit equipped with DSD output function to this unit.

SPDIF
3.SPDIF SPDIF signal is output.

Multi (DVD-Audio)
3.Multi Multi signal is output.

DSD (Direct stream digital)

3.DSD DSD signal is output.

4. SPEAKER SET
The analog switch settings for each sub-menu are as
shown in the table below.

FRONT L/R CENTER SURROUND L/R SURROUND BACK L/R SUBWOOFER

FRNT : SML 0dB SMALL LARGE LARGE LARGE SWFR
CENTER : NONE LARGE NONE LARGE LARGE SWFR
LFE/B : FRNT LARGE SMALL SMALL SMALL FRONT
Pres Mix-P LARGE LARGE LARGE LARGE SWFR
Pres Mix-F LARGE LARGE LARGE LARGE SWFR
Zone2 Amp ON LARGE LARGE LARGE NONE (*) SWFR
Bi-AMP LARGE LARGE LARGE NONE SWFR
TONE : MAX LARGE LARGE LARGE LARGE SWFR
TONE : MIN LARGE LARGE LARGE LARGE SWFR
(*) ZONE2 L/R (EXTRA SP L/R): LARGE
RX-V663/HTR-6160/
DSP-AX763

LARGE: This mode is used for a speaker with high

bass reproduction performance (a large
unit).
Full bandwidth signals are output.
SMALL: This mode is used for a speaker with low
bass reproduction performance (a small
unit).
The signals of 90 Hz or less are mixed into
the channel specified by LFE/BASS.
NONE: This mode is used for no center speaker.
The center content is reduced by 3 dB and
distributed to FRONT L/R.
SWFR: LFE of 5.1 ch signal or LFE/BASS lower than
90 Hz is output through SUBWOOFER OUT.
FRONT: LFE of 5.1 ch signal or LFE/BASS lower
than 90 Hz is distributed to FRONT L/R.

42
 RX-V663/HTR-6160/DSP-AX763

FRONT: SML 0dB

4.FRNT:SML 0dB 90 Hz or lower signal is mixed to the channel specified by LFE/BASS and output.

CENTER: NONE
4.CENTER:NONE The CENTER signal is assigned to FRONT L/R.

LFE / BASS: FRONT

4.LFE/B:FRNT The LFE/BASS signal is assigned to FRONT L/R.

PRESENCE Mix-P
4.Pres Mix-P The PRESENCE L/R signal is increased by 6.0 dB and assigned to FRONT L/R.

PRESENCE Mix-F
4.Pres Mix-F The FRONT L/R signal is increased by 6.0 dB and output.

Zone2 Amp (EXTRA SP) ON

4.Zone2 Amp ON The ZONE2 L/R (EXTRA SP L/R) signal is output.

Bi-AMP
4.Bi-Amp The Bi-AMP signal is output.

TONE: MAX
4.TONE:MAX The signal is output with tone control of “BASS +10 dB” and “TREBLE +10 dB”.

TONE: MIN
4.TONE:MIN The signal is output with tone control of “BASS -10 dB” and “TREBLE -10 dB”.

INPUT: DVD ANALOG

RX-V663/HTR-6160/
SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz
SPEAKER OUT

DSP-AX763
SUBWOOFER
Sub-menu Input level Volume SURROUND SURROUND
FRONT L/R CENTER OUTPUT
L/R BACK L/R
FRNT : SML 0dB Both ch, -20 dBm +6.0 dB +12.0 dBm +12.0 dBm +12.0 dBm +12.0 dBm -3.0 dBm
CENTER : NONE Both ch, -20 dBm +6.0 dB +9.0 dBm -∞ +12.0 dBm +12.0 dBm -7.0 dBm
LFE/B : FRNT (50 Hz) Both ch, -20 dBm +6.0 dB +25.0 dBm +3.0 dBm +3.0 dBm +3.0 dBm -∞
Pres Mix-P Both ch, -20 dBm +6.0 dB +12.0 dBm +12.0 dBm +12.0 dBm +12.0 dBm -7.0 dBm
Pres Mix-F Both ch, -20 dBm +6.0 dB +12.0 dBm +12.0 dBm +12.0 dBm +12.0 dBm -7.0 dBm
Zone2 Amp ON Both ch, -20 dBm +6.0 dB +12.0 dBm +12.0 dBm +12.0 dBm -∞ (*) -7.0 dBm
Bi-AMP Both ch, -20 dBm +6.0 dB +12.0 dBm +12.0 dBm +18.0 dBm +12.0 dBm -7.0 dBm
TONE : MAX Both ch, -20 dBm +6.0 dB +12.0 dBm +12.0 dBm +12.0 dBm +12.0 dBm -7.0 dBm
TONE : MIN Both ch, -20 dBm +6.0 dB +11.0 dBm +12.0 dBm +12.0 dBm +12.0 dBm -7.0 dBm
(*) ZONE2 L/R (EXTRA SP L/R) SPEAKER OUT: +12.0 dBm

43
 RX-V663/HTR-6160/DSP-AX763

5. XCH-INPUT
The input source “MULTI CHANNEL INPUT” is se-
lected.
It is possible to select the 6 ch/8 ch and 6-ohm/8-ohm
by using the sub-menu.
When LIM / PLDET / THM menu is selected, it is pos-
sible to move to the next self-diagnostic function menu
by turning the “PROGRAM” knob of this unit.

6 ch INPUT 6-ohm

5.6CH INPUT_6 Ω

INPUT: MULTI CH INPUT

SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz
SPEAKER OUT SUBWOOFER
Input level Volume
FRONT L/R CENTER SURROUND L/R SURROUND BACK L/R OUTPUT
Both ch, -20 dBm +6.0 dB +12.0 dBm +12.0 dBm +12.0 dBm -∞ -18.0 dBm

8 ch INPUT 6-ohm

5.8CH INPUT_6 Ω

INPUT: MULTI CH INPUT

SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz
SPEAKER OUT SUBWOOFER
Input level Volume
FRONT L/R CENTER SURROUND L/R SURROUND BACK L/R OUTPUT
Both ch, -20 dBm +6.0 dB +12.0 dBm +12.0 dBm +12.0 dBm +12.0 dBm -18.0 dBm

6 ch INPUT 8-ohm

5.6CH INPUT_8 Ω
RX-V663/HTR-6160/
DSP-AX763

INPUT: MULTI CH INPUT

SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz
SPEAKER OUT SUBWOOFER
Input level Volume
FRONT L/R CENTER SURROUND L/R SURROUND BACK L/R OUTPUT
Both ch, -20 dBm +6.0 dB +12.0 dBm +12.0 dBm +12.0 dBm -∞ -18.0 dBm

8 ch INPUT 8-ohm

5.8CH INPUT_8 Ω

INPUT: MULTI CH INPUT

SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz
SPEAKER OUT SUBWOOFER
Input level Volume
FRONT L/R CENTER SURROUND L/R SURROUND BACK L/R OUTPUT
Both ch, -20 dBm +6.0 dB +12.0 dBm +12.0 dBm +12.0 dBm +12.0 dBm -18.0 dBm

44
 RX-V663/HTR-6160/DSP-AX763

LIM / PLDET / THM

LIM: Setting value of LIM (Limiter control)

* Do not change the value settings because

this menu is only for the use of develop-
ment staff.

PLDET: Power limiter detection

The A/D conversion value during operation
is displayed.
(Reference voltage: 5.0 V=255)

THM: Thermo protection detection

The A/D conversion value during operation
is displayed.
(Reference voltage: 5.0 V=255)

255252054000__
(Not applied to these models. / )
THM (Thermo protection detection / )
PLDET (Power limiter detection / )
Limiter control /

6. MIC CHECK
The signals input through the microphone are output
of FRONT L/R via A/D and D/A.

6.MIC CHK --dB

The output level is not indicated.

RX-V663/HTR-6160/
DSP-AX763

45
 RX-V663/HTR-6160/DSP-AX763

7. FL/OSD CHECK
Use this program to check the FL display section and
video control section. When checking the video con-
trol section, connect a TV monitor to this unit with a
component video cable, S video cable and video pin
cable.
Selection of the FL display section or video control
section varies according to the submenu operation as
shown below.
For audio signal processing, use STRAIGHT.

Checking FL display section / Check of the Video control section. (Monitor out) /

Initial display /
Initial display (OSD OFF) /

7.VFD CHECK

All segments OFF /

OSD OFF /

All segments ON (dimmer 100 %) /

OSD OFF /

All segments ON (dimmer 50 %) /

OSD characters ON /
RX-V663/HTR-6160/
DSP-AX763

Lighting of segments in lattice /

OSD characters ON /

Lighting in lattice /

OSD characters /
Short / Normal /

46
 RX-V663/HTR-6160/DSP-AX763

8. MANUAL TEST
Noise is output to all channels through the noise gen-
eration circuit which is included in the microprocessor.
The noise frequency for LFE (SUBWOOFER) is 35 to
80 Hz. Other than that, the noise frequency is 500 to 2
kHz.

TEST ALL
Noise is output from all channels.

8.TEST ALL

9. A/D DATA CHECK

This menu is used to display the A/D conversion value
of the microprocessor which detects panel keys of this
unit and protection functions in using the sub-menu.
During signal processing, the condition before execu-
tion is maintained.
When K0/K1 menu is selected, keys become non-op-
erable due to detection of the values of all keys. How-
ever, it is possible to move to the next self-diagnostic
function menu by turning the PROGRAM knob of this
unit.
* The figures in the diagram are given as reference
only.

PS1/PS2 PS1/PS2
PSx: Power supply voltage protection detection
PS1
Voltage detects: AC_BH, AC_BL, AC12, AC5,
+10, +5.3H and +XM (U, C
models)

RX-V663/HTR-6160/
Normal value: 110 to 205 (Reference volt-

DSP-AX763
age: 5.0 V=255)
PS2
Voltage detects: +12, -12, +5V, +5D, +5I and
+3.3D
Normal value: 88 to 140 (Reference volt-
age: 5.0 V=255)

* If PS1 and PS2 are out of the normal value range,

the protection function works to turn off the power.

PS1:144 2:112

47
 RX-V663/HTR-6160/DSP-AX763

DC/TH
DC: Power amplifier DC protection detection
Power amplifier DC (DC voltage) output is
detected.
Normal value: 5 to 36 (Reference voltage:
5.0 V=255)

TH: THM (Thermo protection detection)

Temperature of the heat sink is detected.
Normal value: 0 to 124 (Reference volt-
age: 5.0 V=255)

* If THM is out of the normal value range, the protec-

tion function works to turn off the power.

DC:020 TH:054

IMP/PL TH/PL
IMP: 8 or 4 ohms impedance setup detection
IMP 8: 8 ohms setting
IMP 4: 6 ohms setting

PL: PLDET (Power limiter detection)

Power amplifier output voltage detection
The power amplifier output voltage is
detected and the power amplifier input
voltage is controlled.

IMP:8 PL:252

U, C, T, K, A, B, G, E, F models (Reference voltage: 5.0 V=255)

During normal operation Value for starting limiter operation Value for canceling limiter operation
PLDET (8-ohm/6-ohm) 255 / 255 87 / 146 125 / 171
RX-V663/HTR-6160/

LIM (Limiter control) H L H

DSP-AX763

R, L models (Reference voltage: 5.0 V=255)

During normal operation Value for starting limiter operation Value for canceling limiter operation
PLDET (8-ohm/6-ohm) 255 / 255 100 131
LIM (Limiter control) H L H

48
 RX-V663/HTR-6160/DSP-AX763

DST/DK
DST: Destination detection
(Reference voltage: 5V=255)

DK: DOCK type detection

(Reference voltage: 5V=255)

DST:027DK:252

Destination detection for AD port

Pull-up resistance 10 k-ohms
Ohm 0.0 k 1.2 k 2.7 k 4.7 k 6.8 k 10.0 k 15.0 k 27.0 k 47.0 k 100.0 k –
V 0-0.3 0.4-0.7 0.8-1.3 1.4-1.8 1.9-2.2 2.3-2.7 2.8-3.2 3.3-3.8 3.9-4.3 4.4-4.7 4.8-5.0
A/D (5 V=255) 0-13 14-40 41-68 69-92 93-115 116-140 141-170 171-198 199-221 222-243 245-255
DEST, 139pin J U, C – R T K A B G, E, F L –

DOCK detection for AD port (IC30 Microprocessor pin no. 128)

Pull-up resistance 10 k-ohms
DOCK DOCK (Develop-
DOCK type Reserved Reserved Reserved No connect
(Bluetooth) (iPod) ment)
Ohm 0.56k 2.7k 5.6k 10.0k 18.0k 39.0k –
DKID (Pin no. 21) 5-25 50-60 85-100 120-140 150-170 195-210 245-255

RX-V663/HTR-6160/
DSP-AX763

49
 RX-V663/HTR-6160/DSP-AX763

K0/K1
K0/K1: KEY0/KEY1 (Panel key of main unit)
The key will fail to function properly if its A/D
conversion value deviates from the specific
range. In that case, check the constant of
partial pressure resistor, solder condition,
etc. with referring to the table below.
(Reference voltage: 5.0 V=100)

K0:255 K1:255

RX-V663 (U, C, R, T, K, A, G, E, F, L models) / HTR-6160 (U, F models) HTR-6160 (C model) / DSP-AX763 (J model)
Display / KEY0 KEY1 Display / KEY0 KEY1
0-4 SYSTEM OFF Zone2 ON/OFF 0-4 – MUTE
5 - 13 SCENE1 SCENE3 5 - 13 SCENE1 SCENE3
14 - 21 SCENE2 SCENE4 14 - 21 SCENE2 SCENE4
22 - 31 – ZONE CONTROL 22 - 31 – SLEEP
32 - 42 – AUDIO SELECT 32 - 42 – AUDIO SELECT
43 - 53 STRAIGHT BAND 43 - 53 STRAIGHT BAND
54 - 61 TONE CONTROL A/B/C/D/E 54 - 61 TONE CONTROL A/B/C/D/E
62 - 68 SEARCH MODE /EDIT PRESET < 62 - 68 SEARCH MODE /EDIT PRESET <
69 - 75 – PRESET > 69 - 75 – PRESET >
76 - 82 SPEAKERS MEMORY 76 - 82 SPEAKERS MEMORY
83 - 89 PURE DIRECT INFO 83 - 89 PURE DIRECT INFO
90 - 100 KEY OFF KEY OFF 90 - 100 KEY OFF KEY OFF

DSP-AX763 (B model)
Display / KEY0 KEY1
0-4 – –
5 - 13 SCENE1 SCENE3
14 - 21 SCENE2 SCENE4
22 - 31 – –
32 - 42 – AUDIO SELECT
RX-V663/HTR-6160/

43 - 53 STRAIGHT –
54 - 61 TONE CONTROL –
DSP-AX763

62 - 68 – –
69 - 75 – –
76 - 82 SPEAKERS –
83 - 89 PURE DIRECT –
90 - 100 KEY OFF KEY OFF

50
 RX-V663/HTR-6160/DSP-AX763

10. VIDEO CHECK

The video circuit is checked by the sub-menu opera-
tion.

I2C (Inter integrated circuit) read/write check

Self-diagnosis is executed to check whether data
reading/writing between the microprocessor con-
nected to the 12C line and each IC is done properly or
not.
0: OK /
I2C:10000101 1: NG /

0 bit: IC83 (DIGITAL P.C.B.)

1 bit: IC84 (DIGITAL P.C.B.)
2 bit: IC82 (DIGITAL P.C.B.)
3 bit: IC10 (DIGITAL P.C.B.)
4 bit: IC17 (DIGITAL P.C.B.)
5 bit: IC16 (DIGITAL P.C.B.)
6 bit: IC392 (VIDEO P.C.B.)
7 bit: IC24 (DIGITAL P.C.B.) (J model)

Digital component
The signal passage as shown below is checked.

DIGITAL COMP

Digital Component

HDMI OUT
HDMI IN

DIGITAL DIGITAL
IC17 DIGITAL IC10
SII9135CTU IC83 SIL9134CTU
ABT1010
I/P SCALAR
DIGITAL DIGITAL
IC82 IC84
ADV7800 ADV7172
Component

Component
VIDEO
VIDEO DECODER VIDEO
IC358 ENCODER

RX-V663/HTR-6160/
OSD

DSP-AX763
S Video S Video

Video Video

51
 RX-V663/HTR-6160/DSP-AX763

Digital CVBS (Video)

The signal passage as shown below is checked.

DIGITAL CVBS

Digital CVBS (Video)

HDMI OUT
HDMI IN

DIGITAL DIGITAL
IC17 DIGITAL IC10
SII9135CTU IC83 SIL9134CTU
ABT1010
I/P SCALAR
DIGITAL DIGITAL
IC82 IC84
ADV7800 ADV7172
Component

Component
VIDEO
VIDEO DECODER VIDEO
IC358 ENCODER
OSD

S Video S Video

Video Video

Digital Y/C (S-Video)

The signal passage as shown below is checked.

DIGITAL Y/C

Digital Y/C (S Video)

HDMI OUT
HDMI IN

DIGITAL DIGITAL
IC17 DIGITAL IC10
SII9135CTU IC83 SIL9134CTU
ABT1010
I/P SCALAR
DIGITAL DIGITAL
IC82 IC84
ADV7800 ADV7172
RX-V663/HTR-6160/

Component

Component

VIDEO
DSP-AX763

VIDEO DECODER VIDEO

IC358 ENCODER
OSD

S Video S Video

Video Video

52
 RX-V663/HTR-6160/DSP-AX763

Analog bypass
The signal passage as shown below is checked.

ANALOG BYPASS

Analog bypass (Conversion OFF)

HDMI OUT
HDMI IN

DIGITAL DIGITAL
IC17 DIGITAL IC10
SII9135CTU IC83 SIL9134CTU
ABT1010
I/P SCALAR
DIGITAL DIGITAL
IC82 IC84
ADV7800 ADV7172
Component

Component
VIDEO
VIDEO DECODER VIDEO
IC358 ENCODER
OSD
Bypass

S Video S Video

Video Video

Test pattern
The test pattern is output from IC84 (DIGITAL P.C.B.).

TEST PATTERN

Test pattern
HDMI OUT
HDMI IN

DIGITAL DIGITAL
IC17 DIGITAL IC10
SII9135CTU IC83 SIL9134CTU
ABT1010
I/P SCALAR
DIGITAL DIGITAL Test IC84 Test pattern
IC82 IC84 pattern

RX-V663/HTR-6160/
ADV7800 ADV7172
Component

Component

DSP-AX763
VIDEO
VIDEO DECODER VIDEO
IC358 ENCODER
OSD

S Video S Video

Video Video

Video information
Displays the information of image signals being input.

Example /
VIDEO IN 480i

53
 RX-V663/HTR-6160/DSP-AX763

11. XM STATUS (U, C models)

The output check of XM radio is executed.
(Connect XM radio antenna module to this unit before
executing.)

1 kHz, -1 dB / 44.1 kHz

1k - 1dB/44 The test tone (1 kHz, -1 dB / 44.1 kHz) is output.

1 kHz, -61 dB / 44.1 kHz

1k -61dB/44 The test tone (1 kHz, -61 dB / 44.1 kHz) is output.

Mute / 44.1 kHz

Mute /44 No signal is output.

XM tone / 44.1 kHz

XM Tone/44 The XM tone / 44.1 kHz is output.

ISO tone / 44.1 kHz

ISO Tone/44 The ISO tone /44.1 kHz is output.

1 kHz, -1 dB / 32.0 kHz

1k - 1dB/32 The test tone (1 kHz, -1 dB / 32.0 kHz) is output.

1 kHz, -61 dB / 32.0 kHz

1k -61dB/32 The test tone (1 kHz, -61 dB / 32.0 kHz) is output.

Mute / 32.0 kHz

Mute /32 No signal is output.

XM tone / 32.0 kHz

XM Tone/32 The XM tone / 32.0 kHz is output.
RX-V663/HTR-6160/

ISO tone / 32.0 kHz

DSP-AX763

ISO Tone/32 The ISO tone / 32.0 kHz is output.

XM bus power: OFF

Bus Power:OFF The power of XM radio antenna module is turned off.

54
 RX-V663/HTR-6160/DSP-AX763

12. SIRIUS (U, C models)

The SIRIUS version is displayed.

SIRIUS:
SIRIUS: -- Connection of the SIRIUS antenna module is checked.
OK : Normal
NG : Abnormal
— : No connected

SR:
SR:FF 00 FF The connection information of the SIRIUS antenna module is displayed.
The result of antenna diagnostic mode (status)
Antenna error history (SSP Error Codes)
Antenna generation (gen_id)

SSP:
SSP: 00 00 00 The SIRIUS version #0 (SSP) is displayed.

MAC:
MAC: 00 00 00 The SIRIUS version #1 (MAC) is displayed.

ADP:
ADP: 00 00 00 The SIRIUS version #2 (ADP) is displayed.

PRDID:
PRDID:00 00 00 The PRD ID (product id) is displayed.

SEQID:
SEQID:00 00 00 The SEQ ID (sequence id) is displayed.

RX-V663/HTR-6160/
DSP-AX763
13. HD RADIO (U model)

CPU version
The sub-microprocessor version in HD radio module
is displayed.

HD CPU V:09.13

DSP version
The DSP version in HD radio module is displayed.

D:DRI-352-V016

55
 RX-V663/HTR-6160/DSP-AX763

14. DOCK
This menu is used to test the DOCK connector without
the iPod itself.
After turning off the power, short between pins No. 14
(TX) and No. 18 (RX), between pins No. 1 (PWR) and
No. 17 (ACCPOW) and between pins No. 4 (iPDET)
and No. 8 (DGND).
Start the self-diagostic function and select the menu.
The check result is displayed according to the follow-
ing display specifications.

Note) Be sure to return the shorted locations to their

original state.

15 16 17 18

9 10 11 12 13 14

3 4 5 6 7 8
10 k-ohms

DOCK: NG NNNN
1/4 W

1 19 20 21 2
All Y / = “OK”
Others / = “NG”

DOCK

Check item / Short pins / Result / Display /

UART loop back test / OK Y 
Pins No.14 (TX) – No.18 (RX) 
NG N 
iPAP (iPod accessory power) detection / Pins No.1 (PWR) IC30 High Y 

– No.17 (ACCPOW) pin No. 141 Low N 
iPDET (iPod installation to DOCK) detection / Pins No.4 (iPDET) IC30 Low Y 

– No.8 (DGND) pin No. 4 High N 
Pins No.21 (DKID) 10 k-ohms, 1/4 W 
DKID (DOCK ID) detection / IC30 Y 
– No.8 (DGND) pull down 
pin No. 28 
RX-V663/HTR-6160/

* 10 k-ohms, 1/4 W pull down Other N 

DSP-AX763

56
 RX-V663/HTR-6160/DSP-AX763

15. HDMI INFORMATION

HDMI model name

MN:RX-V663
The model name of this unit written in HDMI module is displayed.

RX-V663 : (U, C, R, T, K, A, G, E, F, L models)

HTR-6160 : (U, C, F models)
DSP-AX763 : (B, J models)

HDMI product ID
PI:312B The product ID of this unit written in HDMI module is displayed.

3127: RX-V663 (U, C, R, T, K, A, B, G, E, F, L models)

3124: HTR-6160 (U, C, F models)
3126: DSP-AX763 (B model)
3125: DSP-AX763 (J model)

HDMI vendor name

VN:YAMAHA The vendor name “YAMAHA” of this unit written in HDMI module is displayed.

RX-V663/HTR-6160/
DSP-AX763

57
 RX-V663/HTR-6160/DSP-AX763

16. HDMI SELECT

The selected input signal is output to HDMI OUT by
the sub-menu operation.
* Support audio is set to “OTHER”.

HDMI none
HDMI NONE No signal is output.

HDMI in 1
HDMI IN 1 HDMI “IN 1” is output.

HDMI in 2
HDMI IN 2 HDMI “IN 2” is output.

HDMI in 3
HDMI IN 3
HDMI “IN 3” is output.

HDMI up conversion
HDMI UPCONV The analog video signals are output after undergoing Interlace/Progressive conversion.

HDMI up conversion through

HDMI UP THR The analog video signals are output after undergoing video up-conversion.

HDMI up-conversion 1080p

I/P conversion
480i/576i to 480p/576p

HDMI OUT
HDMI IN

DIGITAL DIGITAL
IC17 DIGITAL IC10
SII9135CTU IC83 SIL9134CTU
ABT1010
I/P SCALAR
DIGITAL DIGITAL
IC82 IC84
ADV7800 ADV7172
Component

Component

VIDEO
DECODER VIDEO
RX-V663/HTR-6160/

VIDEO
IC358 ENCODER
OSD
DSP-AX763

S Video S Video

Video Video

HDMI up-conversion through

Up-conversion
HDMI OUT
HDMI IN

DIGITAL DIGITAL
IC17 DIGITAL IC10
SII9135CTU IC83 SIL9134CTU
ABT1010
I/P SCALAR
DIGITAL DIGITAL
IC82 IC84
ADV7401 ADV7172
Component

Component

VIDEO VIDEO VIDEO

IC358 DECODER ENCODER
OSD

S Video S Video

Video Video

58
 RX-V663/HTR-6160/DSP-AX763

17. IF STATUS (Input function status)

The status information is displayed in the hexadeci-
mal notation one after another by the sub-menu op-
eration.
For signal processing, the status before the sub-menu
operation is maintained.
* Mentioning the details is not allowed because this
menu is only for the use of development staff.
* The figures in the diagram are given as reference
only.

DSP status
DST:3000020000

18. DSP BUS CHECK

This menu is used to self-diagnose whether or not the
bus connection for the TI (DA70Y) and the external
ROM/RAM is made properly.

TI BUS:NoEr

NoEr: No error detected.

Boot: When “Boot” is displayed for a few seconds
or “Boot” and “NoEr” are displayed alter-
nately, there is possibility that an error oc-
curs.

19. RESERVED

RX-V663/HTR-6160/
DSP-AX763
20. PROTECTION HISTORY
Four protection histories are displayed.

Example / Example / Example /

20-1.DcPRT 000 20-2.P1PRT:061 20-3.TmPRT:000
History 1 / History 2 / History 3 /

Example /
20-4.NoPRT
History 4 /

21. RESERVED

59
 RX-V663/HTR-6160/DSP-AX763

22. UPDATE
Not applied to these models.

22.UPDATE TI 22.UPDATE CEC

23. FACTORY PRESET

This menu is used to reserve/inhibit initialization of the
user memory (Parameters and set menu contents,
etc. of the sound field program).
The signals are processed using EFFECT OFF (The
L/R signal is output using ANALOG BYPASS).

PRESET INHIBIT (Initialization inhibited) /

23.PRESET INHI
User memory initialization is not executed. Select this sub-menu to protect the user memory.

PRESET RESERVED (Initialization reserved) /

23.PRESET RSRV
Initialization of the user memory is reserved. (Actually, initialization is executed the next time that the
power is turned on.)
Select this sub-menu to reset to the original factory settings or to reset the user memory.
Any protection history will be cleared.

CAUTION: Before setting to the PRESET RESERVED,

write down the existing preset memory con-
tent of the tuner in a table as shown below.
(This is because setting to the PRESET
RESERVED will cause the user memory
RX-V663/HTR-6160/

content of the tuner to be erased.)

DSP-AX763

Preset Group P1 P2 P3 P4 P5 P6 P7 P8
A
B
C
D
E

60
 RX-V663/HTR-6160/DSP-AX763

24. ROM VER. / SUM / PORT

The firmware version and checksum value are dis-
played. The signal is processed using EFFECT OFF.
The checksum is obtained by adding the data at every
8-bit for each program area and expressing the result
as a 4-figure hexadecimal data.
* The figures in the diagram are given as reference
only.

Version
VER: B047U
Firmware version of microprocessor (IC30 DIGITAL P.C.B.) is displayed.

All checksum
Sum: 4913
Checksum value of microprocessor (IC30 DIGITAL P.C.B.) is displayed.

TI FLASH ROM version

TiVer:04.05r2
Firmware version of TI FLASH ROM (IC51 DIGITAL P.C.B.) is displayed.

TiSum:021D2136 TI FLASH ROM checksum

Checksum value of TI FLASH ROM (IC51 DIGITAL P.C.B.) is displayed.

CEC version
CEC Ver: 00.00 Firmware version of CEC (IC24 DIGITAL P.C.B.) is displayed.

RX-V663/HTR-6160/
XM version (U, C models)
XM VER. A006

DSP-AX763
The version of XM firmware is displayed.

SR VER: B003 SIRIUS version

Firmware version of SIRIUS is displayed.

Port
V8 000 U 028
The condition of ports for model detection /
Model: RX-V663/DSP-AX763/HTR-6160
Reserved
RX-V663/DSP-AX763 HTR-6160
MOD0 0 1
MOD1 1 1
MOD2 1 1
Destination: U, C, R, T, K, A, B, G, E, F, L, J

61
 RX-V663/HTR-6160/DSP-AX763

■ CONFIRMATION OF IDLING CURRENT OF AMP UNIT

• Right after power is turned on, confirm that the voltage across
the terminals of R1303 (SURROUND BACK R ch), R1153
(SURROUND R ch), R1154 (FRONT R ch), R1152 (CEN-
TER), R1150 (FRONT L ch), R1151 (SURROUND L ch),
R1149 (SURROUND BACK L ch) are between 0.1 mV and
10.0 mV.
• If measured voltage exceeds 10.0 mV, open (cut off)
R1252 (SURROUND BACK R ch), R1112 (SURROUND R
ch), R1114 (FRONT R ch), R1110 (CENTER), R1106
(FRONT L ch), R1108 (SURROUND L ch), R1104 (SUR-
ROUND BACK L ch) and reconfirm the voltage.

Attention
If the measured voltage exceeds 10.0 mV after repair-
ing a power amplifier first check for a defective compo-
nent before cutting the bias resistor.

• Confirm that the voltage is 0.2 mV to 15.0 mV after 60

minutes.

0.1mV - 10.0mV Open (cut off)

(DC)

R1252 (SURROUND BACK Rch)

R1303 (SURROUND BACK Rch) R1112 (SURROUND Rch)
R1153 (SURROUND Rch) R1114 (FRONT Rch)
R1154 (FRONT Rch) R1110 (CENTER)
R1152 (CENTER) R1106 (FRONT Lch)
R1150 (FRONT Lch) R1108 (SURROUND Lch)
R1151 (SURROUND Lch) R1104 (SURROUND BACK Lch)
R1149 (SURROUND BACK Lch)

Rear

Top view
RX-V663/HTR-6160/
DSP-AX763

MAIN (1) P.C.B.

R1149 R1150 R1151 R1152 R1153 R1154 R1303

R1106 R1108 R1110 R1112 R1114 R1252

R1104

Front
62
 RX-V663/HTR-6160/DSP-AX763

■ DISPLAY DATA
● V401: 17-BT-32GNK (OPERATION P.C.B.) ● ANODE CONNECTION
} 1 17G 16G 15G 14G 13G~1G
1P S1 1-1 1-1
2P 2-1 2-1
PATTERN AREA 3P S8 S15 3-1 3-1
4P S9 S16 4-1 4-1
5P S10 S2 5-1 5-1
6P S3 S11 S18 1-2 1-2

● PIN CONNECTION 7P S5 S12 1a 2-2 2-2

8P S6 S13 1b 3-2 3-2
Pin No. 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35
9P S7 S14 1c 4-2 4-2
Connection F2 NX NP NP P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P26 P27 P28 P29 P30 P31
10P S4 1d 5-2 5-2
Pin No. 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 11P 1e 1-3 1-3

Connection P32 P33 P34 P35 P36 P37 NX NX NX NX NX NX NX 17G 16G 15G 14G 13G 12G 11G 10G 9G 8G 7G 6G 5G 4G 3G 2G 1G NP NP NX F1 12P S21 1f 2-3 2-3

Note : 1) F1, F2 ..... Filament pin 2) NP ..... No pin 3) NX ..... No extend pin 4) 1G~17G ..... Grid pin
13P 1g 3-3 3-3
14P 2a 4-3 4-3
15P 2b 5-3 5-3
16P (ES) 2c 1-4 1-4
● GRID ASSIGNMENT 17P 2d 2-4 2-4
17G 16G 15G 18P 2e 3-4 3-4
19P S20 2f 4-4 4-4
20P S19 2g 5-4 5-4
21P S27 1-5 1-5
22P S28 2-5 2-5
23P S29 3-5 3-5
1G 2G 3G 4G 5G 6G 7G 8G 9G 10G 11G 12G 13G 14G
24P 4-5 4-5
25P S17 5-5 5-5
S3 S1 S14 26P 1-6 1-6
27P 2-6 2-6
S5 S6 S7 S8 S9 S10 S11 S12 S13 S15 S16 28P S30 3-6 3-6
S4 S17
29P 4-6 4-6
30P 5-6 5-6
(16G) (15G)
31P (HOLD) 1-7 1-7
1-1 2-1 3-1 4-1 5-1
32P 2-7 2-7
1-2 2-2 3-2 4-2 5-2 33P S22 3-7 3-7
S22 S2
S24 S24 1a 2b
1-3 2-3 3-3 4-3 5-3
f 34P S23 (RT) 4-7 4-7
S23 b b
a a S29 S28
1-4 2-4 3-4 4-4 5-4 S25 S25 35P S24 5-7 5-7
S26 S21 S20 S19 S18 f g g S27
1-5 2-5 3-5 4-5 5-5 (17G) 36P S25 –
e S28 S29
d d 37P S26 –
1-6 2-6 3-6 4-6 5-6 c c
e
1-7 2-7 3-7 4-7 5-7

(96/24) (DUAL)
(1G~14G) S30

63
 RX-V663/HTR-6160/DSP-AX763

■ IC DATA
IC41: LC89057W-VF4AD-E (DIGITAL P.C.B.) Pin No. Function Name I/O Detail of Function
Digital audio interface transceiver

EMPHA/UO AUDIO/VO INT CL CE CI XMODE

32 33 35 40 39 38 41

RXOUT 1 Cbit, Ubit Microcontroller

37 DO
I/F
RX0 2
36 RERR
RX1 3
RX2 4
Input Demodulation Data
RX3 5 Selector & 21 RDATA
Selector
RX4 8 Lock detect
RX5/VI 9
RX6/UI 10 24 SDIN

16 RMCK
LPF 13 PLL
17 RBCK
Clock 20 RLRCK
TMCK/PIO0 44 Selector
Modulation 22 SBCK
TBCK/PIO1 45 1/N
& 23 SLRCK
TLRCK/PIO2 46 Parallel Port
TDATA/PIO3 47

TXO/PIOEN 48
29 28 27 34
XIN XOUT XMCK CKST

64
 RX-V663/HTR-6160/DSP-AX763

IC44 : D70YE101BRFP266 (DIGITAL P.C.B.)

Floating-point digital signal processors

* No replacement part available. /

Program/Data JTAG EMU

256 RAM
D1 256K Bytes
64 McASP0
Data 32 16 Serializers
R/W Program/Data
C67x+ Microprocessor 256 ROM Page1
256K Bytes 32
D2 Memory
Data 64 Controller Program/Data 32

McASP DMA Bus

R/W ROM Page2 McASP1
256 6 Serializers
256K Bytes 32
Program
I/O INT Fetch Program/Data
ROM Page3 32 McASP2
256
256K Bytes 2 Serializers
256

32 DIT Only

Peripheral Configuration Bus

Program CSP 32 32
32 SPI1
Cache 256
32K Bytes PMP DMP
32 SPI0
32 32
32 I2C0
High-performance
Crossbar Switch 32
32 I2C1

32 32 32 32 32 RTI

32 PLL
I/O Interrupts MAX0 CONTROL MAX1 Events
Out In
EMIF
dMAX
Peripheral Interrupt and DMA Events
SPI0_ENA/I2C1_SDA
SPI0_CLK/I2C0_SCL
SPI0_SCS/I2C1_SCL

EM_BA[0]

EM_BA[1]
EM_CS[2]

EM_CS[0]

EM_A[10]

EM_A[11]
EM_RAS

EM_A[0]

EM_A[1]
EM_A[2]

EM_A[3]

EM_A[4]
EM_A[5]

EM_A[6]
EM_A[7]

EM_A[8]
EM_A[9]
EM_RW
EM_OE

RX-V663/HTR-6160/
CVDD

CVDD

CVDD

CVDD
DVDD

DVDD

DVDD

DVDD
VSS

VSS

VSS

VSS

VSS

VSS
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73

DSP-AX763
VSS 109 72 VSS
SPI0_SIMO 110 71 EM_CKE
SPI0/SOMI/I2C0_SDA 111 70 EM_CLK
DVDD 112 69 VSS
AXR0[0] 113 68 DVDD
VSS 114 67 EM_WE_DQM[1]
AXR0[1] 115 66 EM_D[8]
AXR0[2] 116 65 CVDD
AXR0[3] 117 64 EM_D[9]
VSS 118 63 EM_D[10]
AXR0[4] 119 62 VSS
AXR0[5]/SPI1_SCS 120 61 EM_D[11]
AXR0[6]/SPI1_ENA 121 60 DVDD
AXR0[7]/SPI1_CLK 122 59 EM_D[12]
CVDD 123 58 EM_D[13]
VSS 124 57 CVDD
DVDD 125 56 EM_D[14]
AXR0[8]AXR1[5]/SPI1_SOMI 126 55 EM_D[15]
AXR0[9]AXR1[4]/SPI1_SIMO 127 54 VSS
CVDD 128 53 CVDD
VSS 129 52 EM_D[0]
AXR0[10]/AXR1[3] 130 51 EM_D[1]
AXR0[11]/AXR1[2] 131 50 DVDD
CVDD 132 49 EM_D[2]
VSS 133 48 EM_D[3]
AXR0[12]/AXR1[1] 134 47 VSS
AXR0[13]/AXR1[0] 135 46 EM_D[4]
DVDD 136 45 EM_D[5]
AXR0[14]/AXR2[1] 137 44 CVDD
AXR0[15]/AXR2[0] 138 43 EM_D[6]
ACLKR0 139 42 DVDD
VSS 140 41 EM_D[7]
AFSR0 141 40 VSS
ACLKX0 142 39 EM_WE_DQM[0]
AHCLKR0/AHCLKR1 143 38 EM_WE
AFSX0 144 37 EM_CAS
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
11
1
2
3
4
5
6
7
8
9
AHCLKX0/AHCLKX2
VSS

AMUTE0
AMUTE1
AHCLKX1
VSS
ACLKX1
CVDD
ACLKR1
DVDD
AFSX1
AFSR1
VSS
RESET
VSS
CVDD
CLKIN
VSS
TMS
CVDD
TRST
OSCVSS
OSCIN
OSCOUT
OSCVDD
VSS
PLLHV
TDI
TDO
VSS
DVDD
EMU[0]
CVDD
EMU[1]
TCK
VSS

65
 RX-V663/HTR-6160/DSP-AX763

Pin I/O
Function Name Detail of Function
No. TYPE(1) PULL(2) GPIO(3)
External memory interface (EMIF) address and control
37 EM_CAS O – N SDRAM column address strobe
38 EM_WE O – N SDRAM write enable
39 EM_WE_DQM[0] O – N Write enable or byte enable for EM_D[7:0]
67 EM_WE_DQM[1] O – N Write enable or byte enable for EM_D[15:8]
70 EM_CLK O – N SDRAM clock
71 EM_CKE O – N SDRAM clock enable
74 EM_A[11] O – N
75 EM_A[9] O – N
76 EM_A[8] O – N
79 EM_A[7] O – N
80 EM_A[6] O – N
83 EM_A[5] O – N
EMIF address bus
84 EM_A[4] O – N
86 EM_A[3] O – N
88 EM_A[2] O – N
89 EM_A[1] O – N
91 EM_A[0] O – N
93 EM_A[10] O – N
94 EM_BA[1] O – N
SDRAM bank address and asynchronous memory low-order address
96 EM_BA[0] O – N
97 EM_CS[0] O – N SDRAM chip select
98 EM_RAS O – N SDRAM row address strobe
100 EM_CS[2] O – N Asynchronous memory chip select
102 EM_RW O – N Asynchronous memory read/not write (No connected.)
104 EM_OE O – N SDRAM output enable
External memory interface (EMIF) data bus
41 EM_D[7] I/O – N
43 EM_D[6] I/O – N
45 EM_D[5] I/O – N
46 EM_D[4] I/O – N
48 EM_D[3] I/O – N
RX-V663/HTR-6160/

49 EM_D[2] I/O – N
DSP-AX763

51 EM_D[1] I/O – N
52 EM_D[0] I/O – N
EMIF data bus [Lower 16-bit]
55 EM_D[15] I/O – N
56 EM_D[14] I/O – N
58 EM_D[13] I/O – N
59 EM_D[12] I/O – N
61 EM_D[11] I/O – N
63 EM_D[10] I/O – N
64 EM_D[9] I/O – N
66 EM_D[8] I/O – N
McASP0, McASP1, McASP2 and SPI1 serial ports
2 AHCLKX0 I/O – Y McASP0 and McASP2 transmit master clock
3 AMUTE0 O – Y McASP0 mute output
4 AMUTE1 O – Y McASP1 mute output
5 AHCLKX1 I/O – Y McASP1 transmit master clock
7 ACLKX1 I/O – Y McASP1 transmit bit clock
9 ACLKR1 I/O – Y McASP1 receive bit clock
11 AFSX1 I/O – Y McASP1 transmit frame sync (L/R clock)
12 AFSR1 I/O – Y McASP1 receive frame sync (L/R clock)
113 AXRO[0] I/O – Y McASP0 serial data 0
115 AXR0[1] I/O – Y McASP0 serial data 1
116 AXR0[2] I/O – Y McASP0 serial data 2

66
 RX-V663/HTR-6160/DSP-AX763

Pin I/O
Function Name Detail of Function
No. TYPE(1) PULL(2) GPIO(3)
117 AXR0[3] I/O – Y McASP0 serial data 3
119 AXR0[4] I/O – Y McASP0 serial data 4
120 SPI1_SCS I/O – Y McASP0 serial data 5 or SPI1 slave chip select
121 SPI1_ENA I/O – Y McASP0 serial data 6 or SPI1 enable (Ready)
122 SPI1_CLK I/O – Y McASP0 serial data 7 or SPI1 serial clock
126 SPI1_SOMI I/O – Y McASP0 serial data 8 or McASP1 serial data 5 or SPI1 data pin slave out master in
127 SPI1_SIMO I/O – Y McASP0 serial data 9 or McASP1 serial data 4 or SPI1 data pin slave in master out
130 AXR0[10] I/O – Y McASP0 serial data 10 or McASP1 serial data 3
131 AXR0[11] I/O – Y McASP0 serial data 11 or McASP1 serial data 2
134 AXR0[12] I/O – Y McASP0 serial data 12 or McASP1 serial data 1
135 AXR0[13] I/O – Y McASP0 serial data 13 or McASP1 serial data 0
137 AXR0[14] I/O – Y McASP0 serial data 14 or McASP2 serial data 1
138 AXR0[15] I/O – Y McASP0 serial data 15 or McASP2 serial data 0
139 ACLKR0 I/O – Y McASP0 receive bit clock
141 AFSR0 I/O – Y McASP0 receive frame sync (L/R clock)
142 ACLKX0 I/O – Y McASP0 transmit bit clock
143 AHCLKR0/AHCLKR1 I/O – Y McASP0 and McASP1 receive master clock
144 AFSX0 I/O – Y McASP0 transmit frame sync (L/R clock)
SPI0, I2C0 and I2C1 serial port pins
105 SPIO_ENA I/O – Y SPI0 enable (Ready) or I2C1 serial data
107 SPIO_ENA I/O – Y SPI0 slave chip select or I2C1 serial clock
108 SPIO_CLK I/O – Y SPI0 serial clock or I2C0 serial clock
110 SPIO_SIMO I/O – Y SPI0 data pin slave in master out
111 SPIO/SOMI I/O – Y SPI0 data pin slave out master in or I2C0 serial data
Clocks
17 CLKIN I – N Alternate clock input (3.3 V LVCMOS input)
22 OSCVSS PWR – N oscillator Vss tap point (for filter only)
23 OSCIN I – N 1.2 V oscillator input
24 OSCOUT O – N 1.2 V oscillator output (No connected.)
25 OSCVDD PWR – N oscillator 1.2 V VDD tap point (for filter only)
27 PLLHV PWR – N PLL 3.3 V supply input (requires external filter)
Device reset

RX-V663/HTR-6160/
14 RESET I – N Device reset pin

DSP-AX763
Emulation/JTAG port
19 TMS I IPU N Test mode select
21 TRST I IPD N Test reset
28 TDI I IPU N Test data in
29 TDO OZ IPU N Test data out
32 EMU[0] I/O IPU N Emulation pin 0
34 EMU[1] I/O IPU N Emulation pin 1
35 TCK I IPU N Test clock
Power pins
8
16
20
33
44
53
57 CVDD Core supply
65
77
85
90
101
123

67
 RX-V663/HTR-6160/DSP-AX763

Pin I/O
Function Name Detail of Function
No. TYPE(1) PULL(2) GPIO(3)
128
CVDD Core supply
132
10
31
42
50
60
68
73 DVDD I/O supply
81
92
103
112
125
136
1
6
13
15
18
26
30
36
40
47
54
62
69
72 VSS Ground
78
82
87
RX-V663/HTR-6160/

95
DSP-AX763

99
106
109
114
118
124
129
133
140

1) TYPE column refers to pin direction in functional mode. If a pin has more than one function with different directions, the functions are
separated with a slash (/).
2) PULL column:
IPD = Internal Pull-down resistor
IPU = Internal Pull-up resistor
3) If the GPIO column is ‘Y’, then in GPIO mode, the pin is configurable as an I/O unless otherwise marked.

68
 RX-V663/HTR-6160/DSP-AX763

IC202 : R2A15218FP (FUNCTION P.C.B.)

8 ch electronic volume with 11 input selector and tone control

BASSR2

BASSR1
SBRCIN
SBLCIN

SBRIN2
CLOCK

SBLIN2
SWIN2
DGND

SRIN2
FRIN2
SUBR

SLIN2
FLIN2

TRER
SUBL
DATA

CIN2

N.C.

N.C.
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31
A VCC
MUTE 51 30 AVCC
MCU
AVEE 52 I/F 29 N.C.
A VEE
N.C. 53 28 TREL
0/-6/-12/-18dB
ADCL 54 27 BASSL2
ATT
ADCR 55 26 BASSL1
AGND 56 Bass/Treble 25 N.C.
0~-95dB, -14~+14dB
MAIN -∞ (2dBstep) +42~0dB
N.C. 57 SUB (0.5dBstep) Bypass (0.5dBstep) 24 FRC
MAIN
MAIN
Tone+MIX Tone
INR1 58 Tone 23 FROUT

INL1 59 +42~0dB 22 AGND

(0.5dBstep)

INR2 60 Tone 21 FLOUT

Tone+MIX Tone
SUB

INL2 61 Bass/Treble Bypass 20 FLC

0~-95dB,
-∞ -14~+14dB
(0.5dBstep) (2dBstep)
INR3 62 19 AGND
SUB

CMIX
INL3 63 18 CC
+42~-95dB
-∞(0.5dBstep)
INR4 64 17 COUT

SWMIX
INL4 65 16 AGND
+42~-95dB
INR5 66 -∞(0.5dBstep) 15 SWOUT
+42~-95dB
-∞(0.5dBstep)
INL5 67 14 SWC

INR6 68 13 N.C.
INL6 69 +42~-95dB 12 SRC
-∞(0.5dBstep)

INR7 70 11 SROUT
INL7 71 +42~-95dB 10 AGND
-∞(0.5dBstep)
INR8 72 9 SLOUT

INL8 73 8 SLC
N.C. 74 +42~-95dB 7 A GND
-∞(0.5dBstep)
INRA/RECR1 75 6 SBRC

RX-V663/HTR-6160/
REC
INLA/RECL1 76 5 SBR OUT

DSP-AX763
N.C. 77 4 AGND
INR9 78 3 SBL OUT

INL9 79 2 SBLC
N.C. 80 1 N.C.

81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
INRB/RECR2

INLB/RECL2

INR10/RECR4

INL10/RECL4

INR11/RECR5

INL11/RECL5
N.C.

N.C.

N.C.
RECR3

RECL3

N.C.

FLIN1

FRIN1

CIN1

SWIN1

SLIN1

SRIN1

SBLIN1

SBRIN1

69
 RX-V663/HTR-6160/DSP-AX763

Pin No. Function Name Detail of Function

1 NC
2 SBLC Connects capacitor for reducing click noise of L/R/C/SW/SL/SR/SBL/SBR channel volume
3 SBL OUT Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel
4 AGND Analog ground of internal circuit
5 SBR OUT Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel
6 SBRC Connects capacitor for reducing click noise of L/R/C/SW/SL/SR/SBL/SBR channel volume
7 AGND Analog ground of internal circuit
8 SLC Connects capacitor for reducing click noise of L/R/C/SW/SL/SR/SBL/SBR channel volume
9 SLOUT Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel
10 AGND Analog ground of internal circuit
11 SROUT Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel
12 SRC Connects capacitor for reducing click noise of L/R/C/SW/SL/SR/SBL/SBR channel volume
13 NC
14 SWC Connects capacitor for reducing click noise of L/R/C/SW/SL/SR/SBL/SBR channel volume
15 SWOUT Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel
16 AGND Analog ground of internal circuit
17 COUT Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel
18 CC Connects capacitor for reducing click noise of L/R/C/SW/SL/SR/SBL/SBR channel volume
19 AGND Analog ground of internal circuit
20 FLC Connects capacitor for reducing click noise of L/R/C/SW/SL/SR/SBL/SBR channel volume
21 FLOUT Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel
22 AGND Analog ground of internal circuit
23 FROUT Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel
24 FRC Connects capacitor for reducing click noise of L/R/C/SW/SL/SR/SBL/SBR channel volume
25 NC
26 BASSL1
Frequency characteristic setting pin of L/R channel tone control (Bass)
27 BASSL2
28 TREL Frequency characteristic setting pin of L/R channel tone control (Treble)
29 NC
30 AVCC Positive power supply to internal circuit
31 NC
32 BASSR1
Frequency characteristic setting pin of L/R channel tone control (Bass)
33 BASSR2
RX-V663/HTR-6160/

34 TRER Frequency characteristic setting pin of L/R channel tone control (Treble)
DSP-AX763

35 NC
36 SBLIN2
37 SBRIN2
38 CIN2
39 SWIN2
Input pin of L/R/C/SW/SL/SR/SBL/SBR channel (Multi IN 1/2)
40 SLIN2
41 SRIN2
42 FLIN2
43 FRIN2
44 SBRCIN
Input pin for SBL/SBR channel volume
45 SBLCIN
46 SUBL
Output pin for L/R channel SUB output
47 SUBR
48 DGND Digital ground of internal circuit
49 DATA Input pin of control data
50 CLOCK Input pin of control clock

70
 RX-V663/HTR-6160/DSP-AX763

Pin No. Function Name Detail of Function

51 MUTE Outside mute control pin
52 AVEE Negative power supply to internal circuit
53 NC
54 ADCL
Output pin for L/R channel ADC
55 ADCR
56 AGND Analog ground of internal circuit
57 NC
58 INR1
59 INL1
60 INR2
61 INL2
62 INR3
63 INL3
64 INR4
65 INL4
Input pin of L/R channel (Input selector)
66 INR5
67 INL5
68 INR6
69 INL6
70 INR7
71 INL7
72 INR8
73 INL8
74 NC
75 INRA/RECR1
Input pin of L/R channel (Input selector) / Output pin for L/R channel REC output
76 INLA/RECL1
77 NC
78 INR9
Input pin of L/R channel (Input selector)
79 INL9
80 NC
81 INRB/RECR2
82 INLB/RECL2
83 INR10/RECR4

RX-V663/HTR-6160/
Input pin of L/R channel (Input selector) / Output pin for L/R channel REC output
84 INL10/RECL4

DSP-AX763
85 INR11/RECR5
86 INL11/RECL5
87 NC
88 NC
89 NC
90 RECR3
Output pin for L/R channel REC output
91 RECL3
92 NC
93 FLIN1
94 FRIN1
95 CIN1
96 SWIN1
Input pin of L/R/C/SW/SL/SR/SBL/SBR channel (Multi IN 1/2)
97 SLIN1
98 SRIN1
99 SBLIN1
100 SBRIN1

71
 RX-V663/HTR-6160/DSP-AX763

IC401 : M66003-0131FP (OPERATION P.C.B.)

FL display driver

Display code
RAM CGROM
(35 bit x 166) 44 SEG00
(8-bit x 60)
Code Segment 19 SEG25
write output 17 SEG26
circuit
dot data
CGROM 9 SEG34
CS 2 Serial data (35 bit x 16)
write
SCK 3 receive
circuit Code/
SDATA 4 command
control 45 SEG35
circuit DIG11/
52
SEG42
51 DIG12/
SEG41
code Segment DIG13/
select 50
digit SEG40
select/ 49 DIG14/
XIN 7 Clock output SEG39
timing Display
generator clock controller scan pulse circuit 48 DIG15/
XOUT 6 SEG38
47 DIG16/
SEG37
46 DIG17/
SEG36

63 DIG00
Digit
RESET 1 output
Vcc1 8 circuit
53 DIG10
Vcc2 18
Vss 5
Vp 64
DIG14/SEG39
DIG12/SEG41
DIG13/SEG40
DIG11/SEG42
DIG07
DIG06

DIG08
DIG05

DIG09
DIG00

DIG04

DIG10
DIG01
DIG02
DIG03
RX-V663/HTR-6160/

VP
DSP-AX763

64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49

RESET 1 48 DIG15/SEG38
CS 2 47 DIG16/SEG37
SCK 3 46 DIG17/SEG36
SDATA 4 45 SEG35
Vss 5 44 SEG00
XOUT 6 43 SEG01
XIN 7 42 SEG02
Vcc1 8 41 SEG03
SEG34 9 40 SEG04
SEG33 10 39 SEG05
SEG32 11 38 SEG06
SEG31 12 37 SEG07
SEG30 13 36 SEG08
SEG29 14 35 SEG09
SEG28 15 34 SEG10
SEG27 16 33 SEG11
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
SEG26
Vcc2
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12

72
 RX-V663/HTR-6160/DSP-AX763

Pin No. Port Name Function Name I/O Detail of Function

1 RESET /RESET Reset input When “L”, M66003 is initialized.
2 CS /CEFL Chip select input When “L”, communication with the MCU is possible.
3 SCK CKFL Shift clock input When “H”, any instruction from the MCU is neglected.
4 SDATA DTFL Serial data input Serial input data is taken and shifted by the positive edge of SCK.
5 Vss VSS GND (0V)
6 XOUT XOUT Clock out When use as a CR oscillator, connect external resistor and capacitor.
7 XIN XIN Clock in When use an external clock input external clock to XIN, and XOUT must be opened.
8 Vcc1 VDD Positive power supply for internal logic.
9 SEG34 P1I
10 SEG33 P2
11 SEG32 P3
12 SEG31 P4
13 SEG30 P5 Segment output Connect to segment (anode) pins of VFD.
14 SEG29 P6
15 SEG28 P7
16 SEG27 P8
17 SEG26 P9
18 Vcc2 VDD Positive power supply for DIG and SEG outputs.
19 SEG25 P10
20 SEG24 P11
21 SEG23 P12
22 SEG22 P13
23 SEG21 P14
24 SEG20 P15
25 SEG19 P16
26 SEG18 P17
27 SEG17 P18I
28 SEG16 P19
29 SEG15 P20
30 SEG14 P21
31 SEG13 P22
32 SEG12 P23
Segment output Connect to segment (anode) pins of VFD.
33 SEG11 P24
34 SEG10 P25
35 SEG09 P26
36 SEG08 P27
37 SEG07 P28
38 SEG06 P29

RX-V663/HTR-6160/
39 SEG05 P30

DSP-AX763
40 SEG04 P31
41 SEG03 P32
42 SEG02 P33
43 SEG01 P34
44 SEG00 P35
45 SEG35 P36
46 SEG36 P37
47 DIG16/SEG37 G17I
48 DIG15/SEG38 G16I
49 DIG14/SEG39 G15I
50 DIG13/SEG40 G14
51 DIG12/SEG41 G13
52 DIG11/SEG42 G12
53 DIG10 G11
54 DIG09 G10
55 DIG08 G9 Digital output Connect to digit (grid) pins of VFD.
56 DIG07 G8
57 DIG06 G7
58 DIG05 G6
59 DIG04 G5
60 DIG03 G4
61 DIG02 G3
62 DIG01 G2
63 DIG00 G1
64 VP VP Negative power supply to pull down.

73
 RX-V663/HTR-6160/DSP-AX763

IC30 : M30878FJBGP (DIGITAL P.C.B.)

Single chip 16/32-bit microprocessor

8 8 8 8 8 8 8

Port P0 Port P1 Port P2 Port P3 Port P4 Port P5 Port P6

<VCC2> <VCC1>
Peripheral Functions A/D Converter: Clock Generation Circuit
1 circuit XIN - XOUT
Timer (16-bit) Standard: 10 inputs XCIN - XCOUT

Port P7
Timer A: 5-channel Maximum: 34 inputs(2) On-chip Oscillator
Timer B: 6-channel PLL Frequency Synthesizer

8
UART/Clock Synchronous Serial I/O:
(3)
Three-Phase Motor Control Circuit 7-channel DMAC

Port P8
Watchdog Timer (15-bit) X/Y Converter: DMACII
16-bit x 16-bit

7
D/A Converter: CRC Calculation Circuit (CCITT):

<VCC1>
8-bit x 2-channel CAN Module: 2-channel X16+X12+X5+1

P85
M32C/80 series microprocessor core
Memory
Intelligent I/O

Port P9
R0H R0L FLG
(4) R1H R1L INTB ROM

8
Time Measurement: 8-channel
(5) R2 ISP
Wave Generating: 16-channel
Communication Functions: R3 USP
Clock Synchronous Serial I/O, UART, RAM

Port P10
HDLC Data Processing A0 PC
A1 SVF

8
FB SVP
SB VCT Multiplier

<VCC1> <VCC2>
Port P14 Port P15 Port P11 Port P12 Port P13

7 8 5 8 8

(Note 1)

NOTES:
1. Ports P11 to P15 are provided in the 144-pin package only.
2. Included in the 144-pin package only. 26 inputs maximum in the 100-pin package.
3. 6-channel available in the 100-pin package.
4. 6-channel available in the 100-pin package.
5. 10-channel available in the 100-pin package.
CEP(MOD1)
/TUNED
SP_IMP

/MTSW

/MTHP
/MTSB

/MTCT
/MTFS

LSEL1

LSEL0
/MTZ2
SDRP
SCKP

CKEX

CKEV
SBRY
PDET

SDTP

DTEX

DTEV
/PSW

Z2RY
TRIG

REM

Vcc2

Vcc2
SPC

TMT
PRY
SPB

PSV
SPA

PRI

Vss

Vss
/ST
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73

PDLED 109 72 CPNTD

/RSTFD 110 71 /MTMON
ISA 111 70 /MTVR2
ISB 112 69 /MTVR1
RX-V663/HTR-6160/

TONEA 113 68 /OSDCE(MOD2)

TONEB 114 67 /ICV
DSP-AX763

VRA 115 66 SVDET

RXDSR 116 65 BYPASS(/CE)
VRB 117 64 VIC
TXDSR 118 63 VIB
SCEN0 119 62 VIA
SCEN1 120 61 /HP
M30878FJBGP
SCEN2 121 60 DPWR
/CEFD(MOD0) 122 59 Vcc2
DKPWR 123 58 /ICS
/MIC 124 57 Vss
PLDET 125 56 /AUPH
PRD 126 55 /AUPH_A
SRPWR 127 54 /INTH_RT(/EPM)
DKID 128 53 /RES_Tx
SCKN 129 52 /RES_Rx
Vss 130 FLASH u-com (blank) : X8328A0 M30878FJBGP 51 RMSCN
SDTN 131 FLASH u-com (written by YEM) : X9696A0 (U) M30878FJBGP 50 /PSENB
: X9624A0 (other) M30878FJBGP 49 RMSCNCK
Vcc 132
: X9768A0 (J) M30878FJBGP
ADKEY0 133 48 /HSW_RST(&/RST_C)
ADKEY1 134 47 /AUP_MT
PRV1 135 46 /232SD
PRV2 136 45 SCLH
VPWR 137 44 SDAH
THM 138 43 CTS/BUSY
DEST 139 42 RTS/CLKF
AVss 140 41 Vss
iPAP 141 40 RXDR
VREF 142 39 Vcc1
AVcc 143 38 TXDR
RXDi 144 37 SDAL
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
1
2
3
4
5
6
7
8
9
TXDi
XMPWR
LC
iPDET
DTXM(RDYRDS)
DRXM(RXDRDS)
XMLINK(CLKRDS)
RXDR(for INT)
/ICXM(RSTRDS)
XMREV
/ICADC
/ICDIR
/CSDIR
/ICTI
BYTE
CNVss
/CSTI
/CSDAC
/RESET
Xout
Vss
Xin
Vcc1
/NMI
/INTDIR
/INTTI
/HSW_INT
/SPIRDY
SDD
SCK
SDM
HDMIMT
MUTETI
CDMODE
HSW_CEC
SCLL

74
 RX-V663/HTR-6160/DSP-AX763

I/O

[STBY Sleep]
Pin Function Name

[232C OFF]
VPWR OFF

MCU Sleep
STBY Thrh

STBY CEC
Port Name Detail of Function

STANDBY
Power ON

232C ON
No. (P.C.B.)

[Sleep]
1 TXD4 TXDi SO O O O Asynchronous data output for iPod
2 P95 XMPWR O O O O Power control output for XM antenna
H: ON, L: OFF (U, C models)
3 DA1 LC DA DA I I Limiter control output
4 TB3in iPDET TMR O iPod loaded in DOCK detect
Low when iPod is in Dock
Stop mode (MCU sleep) when set to event counter
5 TXD3 DTXM SO O O [O] Asynchronous data output for XM/DT IC (U, C models)
P92 RDYRDS I I O [O] READY input for RDS IC (G model)
6 RXD3 DRXM SI I O [O] Asynchronous data input for XM/DT IC (U, C models)
RXDRDS SI I O O Synchronous data input for RDS IC (G model)
7 P90 XMLINK I O O O LINK ACTIVE input for XM/DT IC (U, C models)
CLK3 CLKRDS SO O O O Synchronous clock output for RDS IC (G model)
Setting to Low level standby required
8 INT8 RXDR IRQ O RS-232C reception detect (U, C models)
Used for return trigger from stop mode (MCU sleep) / Connect to 40pin
9 P145 /ICXM O O O [O] Reset output for XM/DT IC (U, C models)
RSTRDS O O O [O] Reset output for RDS IC (G model)
10 P144 XMREV I O O O ANT_REV input for XM/DT IC
High: Non-compatible antenna
DIRSDO I O O (O) DIR DATA input for CDDA writing
11 P143 /ICADC O O O O AD converter power down
12 P142 /ICDIR O O O O Initial clear output for DIR
13 P141 /CSDIR CS O O O Chip select output for DIR
14 P140 /ICTI O O O O Initial clear output for TI (DA70Y)
15 BYTE BYTE MCU MCU MCU MCU When set to single chip mode: Vss
16 CNVss CNVss MCU MCU MCU MCU Processor mode select Low: Single chip mode
High: To Flash included boot mode
To boot mode with hardware resetting of P50=H, P55=L, CNVss=H
17 P87 /CSTI CS O O O Chip select output for TI (DA70Y)

RX-V663/HTR-6160/
18 P86 /CSDAC CS O O O Chip select output for DAC (for both 2ch/8ch)
19 RESET /RESET MCU MCU MCU MCU Reset

DSP-AX763
20 Xout Xout MCU MCU MCU MCU
21 Vss Vss MCU MCU MCU MCU
22 Xin Xin MCU MCU MCU MCU
23 Vcc1 Vcc MCU MCU MCU MCU
24 NMI /NMI MCU I I Unused, connect to Vcc
25 INT2 /INTDIR IRQ O O O Interrupt input for DIR
26 INT1 /INTTI IRQ O O O Interrupt input for TI (DA70Y)
27 INT0 /HSW_INT IRQ IRQ IRQ O O MATSUSHITA CEC microprocessor (13 pins) interrupt input
28 P81 /SPIRDY I O O O READY input for TI (DA70Y)
RWCK I O O [O] DIR WCK input for CDDA writing
29 RXD5 SDD SI O O O Synchronous data input for DIR, TI (DA70Y), DAC
DIR: 4M, LSBF TI: 1M, MSBF
30 CLK5 SCK SO O O O Synchronous clock output for DIR, TI (DA70Y), DAC
31 TXD5 SDM SO O O O Synchronous data output for DIR, TI (DA70Y), DAC
DIR: 4M, LSBF TI: 1M, MSBF
32 TA2in HDMIMT TMR TMR O O MDMI AUDIO MUTE input
H: Mute
33 P74 MUTETI O O O O Mute output (High=MUTE) for TI (DA70Y)
34 P73 CDMODE O O O O CDDA write mote control output
H: CDDA write mode L: Normal operation mote
35 P72 HSW_CEC I I I O O MATSUSHITA CEC microprocessor (12 pins) interrupt input
Reset request from MATSUSHITA microprocessor

75
 RX-V663/HTR-6160/DSP-AX763

I/O

[STBY Sleep]
Pin Function Name

[232C OFF]
VPWR OFF

MCU Sleep
STBY Thrh

STBY CEC
Port Name Detail of Function

STANDBY
Power ON

232C ON
No. (P.C.B.)

[Sleep]
36 SCL2 SCLL SIO SIO SIO O O I2C clock input/output for HDMI switcher & video switch
(100kHz device)
Pull up at HDMI block
37 SDA2 SDAL SIO SIO SIO O O I2C clock input/output for HDMI switcher & video switch
(100kHz device)
Pull up at HDMI block
38 TxD1 TXDR SO[O] O RS-232C asynchronous communication data output
TXDF Data output for AF220
39 Vcc1 Vcc MCU MCU MCU MCU Power source of microprocessor +5BU
40 RxD1 RXDR SI [O] O RS-232C asynchronous communication data input
Pull Down by 100k-ohms
RXDF SI Data input for AF220
41 Vss Vss MCU MCU MCU MCU Ground of microprocessor
42 P65 RTS O [O] O RS-232C asynchronous communication RTS output
CLK1 CLKF SI Clock input for AF220
43 CTS1 CTS SI [O] O RS-232C asynchronous communication CTS input
Pull Down by 100k-ohms
RTS1 BUSY SO BUSY output for AF220
44 SDA0 SDAH SIO SIO O O HDMI-RX/TX, VIDEO-DEC/ENC I2C clock input/output
(400kHz device)
Pull up at HDMI block / HDMI Rx,Tx: 5V tolerant
45 SCL0 SCLH SIO SIO O O HDMI-RX/TX, VIDEO-DEC/ENC I2C data input/output
(400kHz device)
Pull up at HDMI block / HDMI Rx,Tx: 5V tolerant
46 P61 /232SD O [O] O 232C driver shut-down control
L: Shut down
Default High (232C ON) for U, C model
Default Low for other than U, C model
47 P60 /AUP_MT O O O O Audio Up conversion Mute output
L: Mute
RX-V663/HTR-6160/

Muted even when audio up conversion is not executed

48 P137 /HSW_RST O O O O O Reset output for HDMI switcher IC
DSP-AX763

L: Reset
49 ISCLK2 RMSCNCK SO O O O Clock output for scene select DVD control remote control code generation
Unused externally
50 P135 PSENB O O O O O O MATSUSHITA CEC microprocessor reset
51 ISTXD2 RMSCN SO O O O Scene select DVD control remote control code output
52 P57 /RES_RX O O O O Reset output for HDMI Rx IC
L: Reset
Pull down at HDMI P.C.B.
53 P56 /RES_TX O O O O Reset output for HDMI Rx IC
L: Reset
Pull down at HDMI P.C.B.
54 P55 /INT_RT I I O O HDMI interrupt (Polarity inversion enabled by HDMI Rx,Tx resistor)
Connect Rx only
Pull up at HDMI P.C.B.
/EPM I 47k-ohms pull down for flash write mode
55 P54 /AUPH_A O O O O O ADC output / Rx output for selection of audio path to HDMI
L: ADC output, H: Rx output
High Fix when VPWR OFF
56 P133 /AUPH O O O O O Video path (Decoder output) to HDMI ON/OFF
L: ON, H: HiZ
High Fix when VPWR OFF
57 Vss Vss MCU MCU MCU MCU

76
 RX-V663/HTR-6160/DSP-AX763

I/O

[STBY Sleep]
Pin Function Name

[232C OFF]
VPWR OFF

MCU Sleep
STBY Thrh

STBY CEC
Port Name Detail of Function

STANDBY
Power ON

232C ON
No. (P.C.B.)

[Sleep]
58 P132 /ICS O O O O O Reset output for VIDEO SCALER IC
L: Reset
Low Fix when VPWR OFF
59 Vcc2 Vcc MCU MCU MCU MCU
60 P131 CEC_DPWR O O O O O ON/OFF control of CEC and DSP power supply
H: ON, L: OFF
DIR, TI DSP, XMIC resetting executed 50ms after DSP power ON
61 P130 /HP I O O O Head Phone detect
L: Head phone in use
62 P53 VIA O O O O O CVBS/S input select A
Low Fix when VPWR OFF
63 P52 VIB O O O O O CVBS/S input select B
Low Fix when VPWR OFF
64 P51 VIC O O O O O CVBS/S input select C
Low Fix when VPWR OFF
65 P50 BYPASS BYPASS CVBS/S select
Low Fix when VPWR OFF
Low Fix when Stby Thrh (10/23 changed)
Input port when standby / Sleep / Backup
/CE I For flash write mode
10k-ohms pull up (+5BU), flash preventive diode
66 P127 SVDET I O O O O S-Video signal detect
Low Fix when VPWR OFF
67 P126 /ICV O O O O Reset output for VIDEO ENC/DEC IC
Low Fix when VPWR OFF
68 P125 /OSDCE CS O O O O Chip enable output for OSD IC
Low Fix when VPWR OFF
Data is taken in with PSV port set to High 20ms after resetting is cancelled
MOD2 I Model detect 2 (663/863)
69 P47 /MTVR1 O O O O O VCR1 MUTE

RX-V663/HTR-6160/
Low Fix when VPWR OFF
70 P46 /MTVR2 O O O O O VCR2 MUTE

DSP-AX763
Low Fix when VPWR OFF
71 P45 /MTMON O O O O O Monitor MUTE
Low Fix when VPWR OFF
72 P44 CPNTD I O O O O Component signal detect
Low Fix when VPWR OFF
73 P43 LSEL0 O O O O O L1 to 3 select 0
Low Fix when VPWR OFF
74 Vcc2 Vcc MCU MCU MCU MCU
75 P42 LSEL1 O O O O O L1 to 3 select 1
Low Fix when VPWR OFF
76 Vss Vss MCU MCU MCU MCU
77 P41 CKEV O O O O PATAPATA synchronous clock output for electronic volume
78 P40 DTEV O O O O PATAPATA synchronous data output for electronic volume
79 P37 /MTHP O O O O Mute Head Phone
80 P36 /MTCT O O O O Mute Center
81 P35 /MTSW O O O O Mute SW
82 P34 /MTSB O O O O Mute SBL/SBR
83 P33 /MTFS O O O O Mute FL/FR/SL/SR
84 P32 /MTZ2 O O O O Mute Zone2
85 P31 CKEX O O O O BATABATA synchronous clock output for expansion input selector
86 P124 DTEX O O O O BATABATA synchronous data output for expansion input selector

77
 RX-V663/HTR-6160/DSP-AX763

I/O

[STBY Sleep]
Pin Function Name

[232C OFF]
VPWR OFF

MCU Sleep
STBY Thrh

STBY CEC
Port Name Detail of Function

STANDBY
Power ON

232C ON
No. (P.C.B.)

[Sleep]
87 P123 CEP CS O O O Chip enable output for tuner PLL
HDRD_N_RST I I I [ I ] Reset output for HD Radio
Use prohibited, always set to input (HiZ)
Data is taken in with PSV port set to High 20ms after resetting is cancelled
(U model)
MOD1 I Model detect 1 (net)
88 RXD6 SDRP SI I O O Synchronous data input for tuner PLL
HDRD_MISO SI I O O Asynchronous data input for HD Radio (U model)
89 CLK6 SCKP SO O O O Synchronous clock output for tuner PLL
90 TXD6 SDTP SO O O O Synchronous data output for tuner PLL
HDRD_MOSI SO O O O Asynchronous data output for HD Radio (U model)
91 Vcc2 Vcc MCU MCU MCU MCU
92 P30 TMT O O O O TUNER Mute output
H: Mute
Always Mute when tuner is not selected
93 Vss Vss MCU MCU MCU MCU Commonly used with ZONE mute being in use when selecting FM/AM band
94 P27 /TUNED I I O O TUNER TUNED input
Pull up to +5S
95 P26 /ST I I O O TUNER STEREO input
Pull up to +5S
96 P25 PSV O O [O] O +5S ON/OFF control
* +5S is OFF in the sleep mode so as to reduce wasteful power consump-
tion when set to low power consumption (Mute circuit, pull up, etc.)
* Shifted to sleep mode about 10 seconds after SYSTEM OFF
97 P24 PRY O O O O Power relay control
98 P23 PRI I I O O Protection excess current detect
99 P22 Z2RY O O O O ZONE2 SP relay control
Z2RY and SPB must not be High at the same time
100 P21 SBRY O O O O Surround back SP relay control
101 P20 SPC O O O O Center & surround SP relay control
RX-V663/HTR-6160/

102 INT5 PDET IRQ O Interrupt input for power down detect
103 INT4 /PSW IRQ O MAIN power/ZONE2 power /SCENE1-4SW interrupt
DSP-AX763

Pressed SW is judged by ADKEY0 and ADKEY1

104 INT3 REM IRQ O Remote control pulse input
105 P14 SPB O O O O Front SP B relay control
106 P13 SPA O O O O Front SP A relay control
107 P12 SP_IMP O O O O ±B voltage control by impedance selection
Power consumption is reduced because B voltage becomes Low
Low (Relay OFF, B voltage High) when set to 8 ohm, High (Relay ON, B
voltage Low) when set to 6 ohms and temperature rises
108 P11 TRIG O O O O DC TRIGGER output
109 P10 PDLED O O O O Pure direct LED
110 P07 /RSTFD O O O O Reset output for FL driver
111 P06 ISA I O O O Rotary A for input selector
112 P05 ISB I O O O Rotary B for input selector
113 P04 TONEA I O O O Rotary A for TONE/PROGRAM
114 P114 TONEB I O O O Rotary B for TONE/PROGRAM
115 P113 VRA I O O O
116 ISRXD1 RXDSR SI O O O Rotary A for volume
Asynchronous communication data input for SIRIUS radio
Serial communication is 5V TTL/CMOS logic level
Pull Down by 100k-ohms
117 P111 VRB I O O O Rotary B for volume

78
 RX-V663/HTR-6160/DSP-AX763

I/O

[STBY Sleep]
Pin Function Name

[232C OFF]
VPWR OFF

MCU Sleep
STBY Thrh

STBY CEC
Port Name Detail of Function

STANDBY
Power ON

232C ON
No. (P.C.B.)

[Sleep]
118 ISTXD1 TXDSR SO O O O Asynchronous communication data output for SIRIUS radio
Serial communication is 5V TTL/CMOS logic level (U, C models)
119 P03 SCEN0 O O O O SCENE button LED control 0
120 P02 SCEN1 O O O O SCENE button LED control 1
121 P01 SCEN2 O O O O SCENE button LED control 2
122 P00 /CEFD CS O O O Chip enable output for FL driver
Data is taken in with PSV port set to High 20 ms after resetting is cancelled
MOD0 I Model detect 0 (RX/HTR)
123 P157 DKPWR O O O O DOCK power control output / H: ON, L: OFF
124 P156 /MIC I O O O MIC detect
125 AN155 PLDET AD AD O O SP output level detect for AD power limiter
Refer to the limiter setting table
126 AN154 PRD AD AD O O AD protection power amplifier DC detect
Refer to the protection setting table
127 P153 /SRPWR O I I I SIRIUS radio power enable output
L: Power ON HiZ: Power OFF
Used as input port because SIRIUS power turns ON if set to Low Fix when in
the Standby/Sleep mode (U, C models)
128 AN152 DKID AD AD AD O AD Dock ID judgment
The type of Dock being connected is judged and operation is changed
129 ISCLK0 SCKN SO O O O Synchronous clock output for FL DRIVER IC
SO O O O Synchronous clock output for OSD IC
Include 1k-ohms in the series to make applicable to pure direct
130 Vss Vss MCU MCU MCU MCU
131 ISTXD0 SDTN SO O O O Synchronous data output for FL DRIVER IC
SO O O O Synchronous data output for OSD IC
Include 1k-ohms in the series to make applicable to pure direct
132 Vcc1 Vcc MCU MCU MCU MCU
133 AN7 ADKEY0 AD AD [I] O AD KEY1 for taking in AD value
134 AN6 ADKEY1 AD AD [I] O AD KEY0 for taking in AD value

RX-V663/HTR-6160/
135 AN5 PRV1 AD AD O O AD protection power voltage detect1
136 AN4 PRV2 AD AD O O AD protection power voltage detect2

DSP-AX763
137 P103 VPWR O O O O CIDEO power control
Low when VIDEO OFF
Set according to specifications of pure direct and return to Low Fix when in
Standby/Sleep mode
138 AN2 THM AD AD O O AD temperature detect
Refer to the protection setting table
139 AN1 DEST AD AD O O AD destination discrimination
Data is taken in when resetting is cancelled
140 AVss AVss MCU MCU MCU MCU
141 P100 iPAP I I I O iPod accessory power detect
Becomes Low while iPod is booting (for about 2 seconds)
Identification executed when booting is judged as completed
142 Vref VREF MCU MCU MCU MCU
143 AVcc AVcc MCU MCU MCU MCU
144 RXD4 RXDi SI I I O Asynchronous data input for iPod

Standby --- All Zone power OFF, Master ON

MCUSleep --- Low current consumption state at Master OFF

79
 RX-V663/HTR-6160/DSP-AX763

Key detection for AD port

Key input (A/D) pull-up resistance 10 k-ohms
RX-V663 (U, C, R, T, K, A, G, E, F, L models), HTR-6160 (U, F models)
Ohm 0 +1.0 k +1.0 k +1.5 k +2.2 k +3.3 k +4.7 k +4.7 k +6.8 k +10.0 k +22.0 k
V 0-0.23 0.24-0.64 0.65-1.06 1.07 - 1.55 1.56-2.09 2.10-2.622.63-3.06 3.07-3.40 3.41-3.73 3.74-4.07 4.08-4.45
ADKEY0 SYSTEM TONE SEARCH PURE
SCENE1 SCENE2 – – STRAIGHT – SPEAKERS
(133 pin) OFF CONTROL MODE / EDIT DIRECT
ADKEY1 Zone2 ZONE AUDIO
SCENE3 SCENE4 FM/AM A/B/C/D/E PRESET < PRESET > MEMORY INFO
(134 pin) ON/OFF CONTROL SELECT

HTR-6160 (C model), DSP-AX763 (J model)

Ohm 0 +1.0 k +1.0 k +1.5 k +2.2 k +3.3 k +4.7 k +4.7 k +6.8 k +10.0 k +22.0 k
V 0-0.23 0.24-0.64 0.65-1.06 1.07-1.55 1.56-2.09 2.10-2.622.63-3.06 3.07-3.40 3.41-3.73 3.74-4.07 4.08-4.45
ADKEY0 TONE SEARCH PURE
– SCENE1 SCENE2 – – STRAIGHT – SPEAKERS
(133 pin) CONTROL MODE /EDIT DIRECT
ADKEY1 AUDIO
MUTE SCENE3 SCENE4 SLEEP FM/AM A/B/C/D/E PRESET < PRESET > MEMORY INFO
(134 pin) SELECT

DSP-AX763 (B model)
Ohm 0 +1.0 k +1.0 k +1.5 k +2.2 k +3.3 k +4.7 k +4.7 k +6.8 k +10.0 k +22.0 k
V 0-0.23 0.24-0.64 0.65-1.06 1.07-1.55 1.56-2.09 2.10-2.622.63-3.06 3.07-3.40 3.41-3.73 3.74-4.074.08-4.45
ADKEY0 TONE PURE
– SCENE1 SCENE2 – – STRAIGHT – – SPEAKERS
(133 pin) CONTROL DIRECT
ADKEY1 AUDIO
– SCENE3 SCENE4 – – – – – – –
(134 pin) SELECT

Destination detection for AD port

Pull-up resistance 10 k-ohms
Ohm 0.0 k 1.2 k 2.7 k 4.7 k 6.8 k 10.0 k 15.0 k 27.0 k 47.0 k 100.0 k –
V 0-0.3 0.4-0.7 0.8-1.3 1.4-1.8 1.9-2.2 2.3-2.7 2.8-3.2 3.3-3.8 3.9-4.3 4.4-4.7 4.8-5.0
A/D (5 V=255) 0-13 14-40 41-68 69-92 93-115 116-140 141-170 171-198 199-221 222-243 245-255
DEST, 139pin J U, C – R T K A B G, E, F L –

Model detection
1: Pull-up / 0: Pull-down
Model RX-V663/DSP-AX763 HTR-6160
/CEFD/MOD0 (122 pin) 0 1
RX-V663/HTR-6160/
DSP-AX763

80
 RX-V663/HTR-6160/DSP-AX763

■ PIN CONNECTION DIAGRAMS

ICs
ADV7172KST ADV7800BSTZ-80 BA15218F
132 89

133 88
48 37

1 36

12 25
8 4
13 24 1
176 45

1 44

BD3841FS D70YE101BRFP266 EN29LV160AB-70TCP F2621E-01-TR KIA7812API

M30878FJBGP
108 73

109 72

36 25
1 48
37 24

16 48 13
32 24 25 IN
1 12
OUT
144 37 COM
1
36 1

KIA7912PI LA73050-TLM-E LC72725KM-UY-TLM-E LC74782JM-8A16-TLMC

PCM1780DBQR
PCM1781DBQR

18

RX-V663/HTR-6160/
12
8 24

DSP-AX763
36 16
GND
OUT 1 1
IN 1

LC89057W-VF4AD-E LM61CIZ M12L64164A-5TG M66003-0131FP-R MN103SFD7G

24 13 96 65
54 28 48 33 97 64
25 12 49 32

36 1 64
+VS 17
VOUT 128 33
37 48 GND 1 27 1 16
1 32

NJM2068MD-TE2 NJM2388F05 NJM2388F09 NJM2581M NJM2867F3-05 NJM4565M

NJM2396F33 TC74VHC08FT TC7SET32FU
TC74VHCU04FT

8 4 4
1 1 7 5
1 1. VIN 1. VIN 14 3 8 4
2. VOUT 4 4
2. VOUT 1
3. GND 3. GND 1 1
4. ON/OFF CONTROL 4. ON/OFF CONTROL
81
 RX-V663/HTR-6160/DSP-AX763

NJM7805FA NJM78M05DL1A NJW1321FP1 PCM1803DBR

NJM7812FA SN74LVC245APWR
SN74LVTH245APW
TC74VHC541FT
TC74VHCT541AFT
2 38 25
39 24

10
1
1: IN 48 15 20
1: INPUT 3
1 2: GND
23 2: GND 1 14
3: OUT 1
3: OUTPUT

PCM1680DBQR R1154H058B-T1-F R1172H181B-T1-F R1172S121D-E2-F R1232D181A-TR-F

R1172H331D-T1-F R1172S181B-E2-F
R1172S331B-E2-F

1
1
14 1: CE
3 2: GND 8
3 3: NC 6
28 5 4
5 4: VDD 3
4 5: VOUT 1 1
4
1

R2A15218FP SiI9134CTU SiI9135CTU SiI9185ACTU

75 51 108 73

109 72 60 41
76 50
61 40
80 51

81 50

100 31 80 21
100 26
1 30 144 37 1 20
1 25
1 36
RX-V663/HTR-6160/

TC74HC4053AF TC74VHC153FT TC7WZ32FK

DSP-AX763

TC4013BP TC4051BF TC74HC4051AFEL

TC74HC4052AF TC74VHC157FT

8 8 8 8 4
7 16 8
16 16
14 16 1
1 1 1
1 1

82
 RX-V663/HTR-6160/DSP-AX763

Diodes
1N4002S 1SS355 D6SBN20 DB105 MA8024-(TX) 2.4V
1SS133 1SS380
1SS176 Anode Anode
1SS270A Anode
+
–

Cathode –
Cathode
AC AC Cathode
+ AC AC

MA8030-L 2.9V MA8091-M 9.1V MTZJ2.4B RB441Q-40 RB500V-40

MA8036 3.6V MA8100-H 10.3V MTZJ5.1C RB501V-40
MA8051-M 5.1V MA8100-M 10.0V MTZJ6.2B Anode Anode
MA8056-M 5.6V Anode MTZJ13B Anode
MA8068-M 6.8V MTZJ15B
MA8075-H 7.7V MTZJ30A
MA8091-L 8.8V
Cathode Cathode Cathode Cathode

RLZ7.5B 7.5V RS103-B-D-V50 RS203M-B-C-J80 RS403M SB01-05Q

RS603M
3
Anode
Cathode
2
3
1
– – – 1
Cathode AC AC Anode 2: (No connect)
AC AC AC
+ AC +
+

RX-V663/HTR-6160/
DSP-AX763

83
 RX-V663/HTR-6160/DSP-AX763

Transistors
2N5401C-AT/P 2N5551C-AT 2SA949 2SA1576A 2SA1695 O,P,Y 2SA1708
2SA1015-Y 2SC1815 Y 2SC4468 O,P,Y
2SC2240 2SC2229

E B
E B C
C B E B C E
B CE C
B E

2SA1770S/T-AN 2SC1740S 2SC2412K 2SC3326-A (TE85R, F) 2SC4614S/T-AN 2SD1915F 2SD2014

2SC3326-B (TE85R, F)
2SC4081 T106
2SD1938F
KTA1504S
KTC3875S
C C

E E E
C B B E
B CE B C E B
B CB CE

2SK246-Y (TPE2, F) 2SK3850 3LN01C-TB-E DTA114EKA KRA102M-AT/P

D
DTA143EKA
DTA144EKA
DTC114EKA
DTC124EKA
D DTC144EKA 3

1: Source 1
S 1: GND
2: Gate G 2 2: IN
1 G D 3: OUT E
23 3: Drain CB
S

KRA102S-RTK/P KRC102M-AT KTA1046-Y-U/P RSR025P03TL µPA672T-T1-A

KRC102S-RTK
KRC104S-RTK
1. Source 1 (S1)
3 2. Gate 1 (G1)
RX-V663/HTR-6160/

OUT 4
1: GATE 3. Drain 2 (D2)
2 6 4. Source 2 (S2)
2: SOURCE 3
DSP-AX763

COMMON 5. Gate 2 (G2)

1 3: DRAIN 6. Drain 1 (D1)
E BC 1
IN CB
E

84
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

1
■ BLOCK DIAGRAMS
AUDIO (DIGITAL) SECTION BLOCK DIAGRAM

DIGITAL • See page 105-109 →

2 SCHEMATIC DIAGRAM
IN1

DVD

IC16 IC17
IN2

DVR HDMI Switcher HDMI Dual Receiver

SII9135CTU

86 85 81 82 83 84 78 89
SCK/DCLK
WS/DR0
SD0/DL0
SD1/DR1
SD2/DL1
SD3/DR2
SPDIF/DL2
MCLK
3
2 18 MCLK
9 11 SCK/DCLK
8 12 WS /DR0

Buffer
IC13
7 13 SD0/DL0
HDMI

6 14 SD1/DR1
5 15 SD2/DL1
4 16 SD3/DR2
3 17 SPDIF/DL2

IC12 Rx_MCLK Selector Control

MCLK Selector Rx_SCK
SCK CKSELA PDSEL
6 Rx_WS ADC_MCLK
WS CKSELB
Rx_SD0 ADC_SCK
SD0 7 MCLK
ADC_WS IC45, 46
SCK
SPDIF

Selector
DCLK

5 ADC_SDO WS
4
DR0

DR1

DR2

SD1
SD2
SD3
DL0

DL1

DL2

SD0 TC74VHC
RMCK MCLK IC44 SELMCK
RBCK DCLK DSP SELBCK
15 16 17 18 19 20 21 8 7 6 4 9
RWCK - D70YE101 SELWCK
IC56 SELSDO
IC10 ADSDO DL0 IC62 DABCK
Audio Upconv. Mute SELSDO Selector DABCK
HDMI Transmitter RMCK SELMCK DAWCK
OUT DAWCK
RBCK SELBCK TIBCK DASD_P 5
SIL9134CTU DASD_P
RWCK SELWCK TIWCK DASD_F
DIRSDO SELSDO TISD_P IC64
Post TISD_F DABCK
IC41 XMMCK Decoder 2ch DAC 15,14
Processor DAWCK
MD/CD-R 1 DIR 44-46 XMBCK + IC68 DAFL/DAFR
OUT

SD1/DR1 DASD_F
2C89057W XMWCK -
Rec SD2/DL1 27,26
2 XMSDO SD3/DR2 116 TISD_C 11 22,21 IC69 DAC/DASW
IC65 -
DL2 115 TISD_S 12 20,19 IC70 DASL/DASR
OPTICAL

8ch DAC -
V-AUX SPDIF 3 DR0 113 TISD_SB 13 16,15 IC71 DASBL/DASBR
RMCK -
RBCK
5 MD/CD-R 4 RWCK
IN

DIRSDO

Selector
DVD 5 16,17,20,21
DIR IC49 IC51
64M SDRAM 16M Flash ROM
DTV/CBL 8
RMCK
COAXIAL

CD 9 RBCK
IC52 RWCK R682, 693
Buffer IC66 IC67 R694 ,683
DVD 10 24 ADSDO 12
2ch ADC
1,2
TC74VHCU04 + Att.

Q602,604
MIC SW MCSEL Selector Control
(V663 UC)

YPAO MIC
6

Sirius
XMMCK
U, C models XMBCK
XMWCK

DASVL/DASBR
IC42 XMSDO IC61 IC72

DASL/DASR
DAFL/DAFR

DAC/DASW
XM +
XM/DT IC 2ch DAC

XML/XMR

ADL/ADR
SRL/SRR
U, C models

MIC
to AUDIO SECTION

85
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

AUDIO (ANALOG) SECTION BLOCK DIAGRAM

To DIGITAL AUDIO SECTION

DASBL/DASBR
DASL/DASR
DAFL/DAFR
DAC/DASW
ADL/ADR
SIRIUS
2

MIC
XM
DOCK
J2006
(R, T, K, A, B, G, E, F, L, J models)
FL/FR

3 Center

SL/SR

PRE OUT
IC227 Muting
Q2007,2008 SBL/SBR
J2004,2005
J2002,2003

2009,2010

SUBWOOFER
TUNER Muting
(U, C models)
J2024,2025

(B model) Q2255,2261 SW1

Muting
SW2
4 V-AUX Q2507,2508

(R, T, K, A, B, G, E, F, L, J models)
PHONO EQ R2216
54.55 IC220 R2217
PHONO IC201
Muting
R2A15215FP PHONES
Q2201,2202
CD IC202
C4302,4304
BA15218F
AUDIO

70,71
MD/CDR 0dB~+42dB FL/FR IC225
MASTER VOLUME (-95dB~0dB)
INPUT & ZONE2 SELECTOR

21,23
DVD 81,82 Tone Center Mix RY100
FRONT A
Control LFE Mix
C1115,1116
8ch SELECTOR

DTV/CBL 83,84
RY101
Muting FRONT FRONT B/ZONE B/
Center IC226 Q2252,2253 ZONE2/ PRESENCE
DVR Center 2258,2259
17 C1117,1118
5 VCR 0dB~+42dB
SL/SR RY106
SR L/R
9,11
0dB~+42dB
SBL/SBR or Z2L/Z2R
MD/CDR SB L/R 3,5
RY103
REC OUT

Muting

SPEAKERS
0dB~+42dB SW CENTE CENTER
DVR SW Q2254,2260
15 C1153
0dB~+42dB
VCR

Muting 46,47 36-43

ZONE2 Q2001-
2004 Muting SURR. RY104
U, C, R, T, K, A, L models & HTR (C) SURROUND
Q2251,2256
MUTE CONTROL 2263,2264 C1119,1114

6 FL/FR
MULTI CH INPUT

SBL/SBR

C/SW Muting SRB. RY102 SURROUND BACK

Q2257,2262 /BI AMP
C1108,1111
SL/SR
POWER AMP
MUTE CONTROL

IC226
FUNCTION • See page 110, 111 →
SCHEMATIC DIAGRAM

7 SPEAKER RELEY

86
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

VIDEO SECTION BLOCK DIAGRAM

/HSW_ INT

HSW_CEC
/INTH_RT

/RES_Tx

/PSENB
SDAH
SCLH

SDAL
SCLL
(J model)

/RST

SDA
SCL
/INT

/RESET

CSDA
CSCL
IC24
IC10 CEC Microprocessor
HDMI Transmitter MN103SFD76YAB
SiI9134CTU
NTSC: 14.3181MHz
PAL: 17.7344MHz 28.636363MHz

HSYNC
Q[0:35]

VSYNC
Q800

IDCK

OUT
DE
SDAL
2 SCLL
SDTN IC85
C2412
OSD 115
/VSY SCKN OSD CVOUT -6dB AIN6 P[20:29]
SVDET /INTH_RT /OSDCE
LC74782
CPNTD /RES_Rx P[10:19]
AD V 112
VSYNC AIN11 Field/DE

Main Microprocessor
VIA /RES_Tx BLANK
VIB /AUPH

HDMI
VIC /INT_AD

Q[0:35]

DE
VSYNC
HSYNC
ODC
/ICV
VIDEO LSEL0
HDMI
LSEL1 SCLH IC86 IC82
AD SY 110
SDAH SVDET Detector AIN12 VIDEO Dec. & I/P 27MHz
BYPASS IC16
74HCU04 114 ADV7800 IC89 IC17
SDTN SCLV AIN10 HDMI Switcher

IN2
SCKN AD SC 8 HDMI Dual Receiver
SDAV DAY SiI9185A
P[2:9] DACA SiI9135CTU
/OSDCE /ICS AD Pr 98 DACb

/RST

SDA
AIN3 DACB

SCL
/INT
LLC CLOCK

CSDA
/MTMON IC84

CSCL

IN1
/RST
AD Pb 96 DACr

/INT
DACC
/MTVR1 AIN2 HS HSYNC VIDEO Enc.
DACD DAV
/MTVR2 91 ADV7172
AIN1 VS VSYNC DASY
IC87 DACE
AD Y 94 DAC
SOY DACF

/HSW_ INT

/HSW_RST
HSW_CEC

SDAL
SCLL
Detector
3 CPNTD SFL SCRESET/RTC

/INTH_RT

/RES_R

SDAH
SCLH
74HCU04

DIGITAL • See page 105-109 →

SCHEMATIC DIAGRAM

RECOUT IC333 RECOUT AMP

LA73050
DVD DVR
6dB

DTV/CBL INPUT SELECTOR

VIA VCR
VIB Q3001
DVR CVBS
VIC 2SA1576A REC OUT
6dB
VCR CVBS C Y
0dB
MONITOR DVR
4 OUT
IC302
C Y
6dB
iPod VCR
74HC4051x2 AD V
VIDEO

C Y Q3002
Y
2SA1576A
DVD BYPASS Sw OUTPUT AMP
Y

/MTVR1
AD SY 74HC4053 LA73050

/MTVR2
0dB
DTV/CBL IC304 IC332
CVBS
IC303 CVBS 6dB
DVR
Q3003
C MONITOR OUT
VCR 2SA1576A Y
SY 6dB
C AD SC C Y
0dB
MONITOR
OUT C
SC 6dB
IC301 LPF
iPod
BYPASS
CD4051 VIA9
5 VIB9
VIC9 BYPASS /MTMON
VIDEO (1) • See page 114 →
SCHEMATIC DIAGRAM

Pb/Cb

Pr/Cr
DVD
Y Cb Cr
S2 DET 0V 2.2V 5V
L1/L2/L3
PORT 3 AD Y
Y OUT1
COMPONENT VIDEO/D5 VIDEO

Pb OUT1 AD Pb
Y Pr OUT1 AD Pr
6 Pb
DA Y
SCL
Y IN 4
6dB Y
SCLL DA Pb
IC392 Pb IN 4
Pr SDAL SDA
Pr IN 4 DA Pr Pb
INPUT SELECTOR (0 dB Amp.)
Y NJW1321
6dB Pr
L1/L2/L3 Cb Cr Y OUT2 MONITOR OUT
DVR Y/Pb/Pr
Pb OUT2
IN Y IN 1~3
Pb IN 1~3 Pr OUT2
Pr IN 1~3 /CNON L1/L2/L3
Y 6dB
AUX 3
X
Pb PORT 0~2 AUX 0~2
/MTMON IC351
Pr
L1 L2 L3 IN L1 L2 L3 OUT OUTPUT AMP
VCR NJM2581
Y Cb 0V 2.2V 5V 0V 2.2V 5V
Cr
L1/L2/L3 IC383,384
SELECTOR
74HC4052 x2
7
LSEL0 VIDEO (2) • See page 115 →
LSEL1 SCHEMATIC DIAGRAM
(J model)

87
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

POWER SECTION BLOCK DIAGRAM

/4ohm
AC_BL RY105
AC_BH
+B

C1095 C1094

D1040
G
MAIN (1)
2 • See page 113 →
RY105 -B SCHEMATIC DIAGRAM

AC12 +18 +12V

+12

C1083 C1082
IC104

D1035
G
FUNCTION (1)
-18 -12V • See page 110 →
FUNCTION (3) • See page 111 →
-12
IC105 SCHEMATIC DIAGRAM
SCHEMATIC DIAGRAM
-28V
-VP
Q1068 OPERATION (1)
3 +10 +5V • See page 112 →
+5V SCHEMATIC DIAGRAM

C1088 C1087
IC106
RY251 F2502

D1036
AVPWR
G

F2501/J2502
-10 -5V
Q1100 -5V
Q1103
AVPWR
ACI +IPOD +5V

TE251
+5I

D1048
IC110

C1112
AC IN
IGND VIDEO (1)
(R, T, K, A, B, G, E, F, L, J models)
+9V
+9V • See page 114 →
IC305
4 Power Detector
SCHEMATIC DIAGRAM
VPWR
IC251,252,253 /Reset
Q2501,2503
+5V
/RES IC63 +5A
J2503

D2512

+5V +3.3V
Q2504

IC102 +3.3V
IC48
DPWR
+5D
s10 +3.3V +1.2V
IC107 IC47 +1.2V
Q2502 RY251

(U, C models) DPWR

+3.3D
D2514

+5.3V
IC100 +5.3X
5 FUNCTION (3)
XMPWR (U, C models)
• See page 111 →
SCHEMATIC DIAGRAM +5V
IC11 +5VPower
POWER RELAY
+3.3HSW
+3.3V +1.8V
IC21 IC19 +1.8HSW

AC_HDMI +11H +5V

+5V +5HV
D2515

D2502
C2505 IC110
Q1104,1106 +1.8V
IC20 +1.8H
D2516 VPWR
Q2509 +3.3HV
+3.3V +1.8V
PVDD
6 (U, C models) IC80 IC94
VPWR

+1.8V
+1.8H
IC81
VPWR D311
+5.8V
IC31/32 +5BU

D310
+5M

D309 Q300
+5S

MG DIGITAL
7 POWER MAIN (2) POWER SAVE • See page 105-109 →
TRANSFORMER SCHEMATIC DIAGRAM
• See page 113 →
SCHEMATIC DIAGRAM

88
 7
6
5
4
3
2
1
A

FUNCTION (3)
Q2503 Interrupt for AC Power Detection 102 PDET DEST Set Destination
139
• See page 111 → R305,306
AC Power
SCHEMATIC DIAGRAM Q2501 Reset for Microprocessor /RES
19
Reset PSV Power Save (+5S ON/OFF) Q300
96

Power Relay Control PRY +5S Switch

97
Power Relay FUNCTION (1)
38
TXDR
40
RXDR Serial control (UART) CB36 • See page 110 →
42
CLKF (RTS) Flash Connector SCHEMATIC DIAGRAM
43
BUSY (CTS)

MAIN (1)
Amplitune Amplitude Detection for Power Limit PLDET
125
• See page 113 → Detector Clock for RDS
SCHEMATIC DIAGRAM Reset for RDS
B

IC241
Tracking Power Power Limmiter Control 3 LC
RDS IC
Supply RDS Serial Control

JK100 5
DTXM (RDYRDS) XM Serial Control (UART)
Remote In 6
DRXM (RXDRDS)
JK201 Scene Remote Out RMSCN /ICXM (RSTRDS) 9
Reset for XM IC42
49
Remote Out XMLINK (CLKRDS) XM Link Active Detect XM/DT IC
7
JK102 Trigger Out TRIG XMREV XM Antenna Detect
108 10
Trigger Out

106 105 101 100 99

Speaker Realay Control SPA, SPB, SPC, SBRY, Z2RY XMPWR 2 XM Bus Power ON/OFF IC100
Speaker Relay
Regulator

8/6 ohm SP. Impedance Control SP_IMP

107
Relay
C

/SRPWR 127 Sirius Power Enable

JK41
High Current I Protection 98 PRI
Sirius
118
( I ) Detector TXDSR Sirius Serial Control (UART)
Connector
116
DC Protection 126 PRD RXDSR
DC Detector

Power Supply Voltege Protection 1 PRV1 30

135 SCK
Voltage Detector1 31
Serial Control (SPI)
SDM
29
SDD
/ICDIR Reset for DIR IC41
12

/CSDIR Chip Select for DIR DIR

13
MAIN (2) /INTDIR Interrupt from DIR
25
Power Supply Voltage Protection 2 PRV2
136
• See page 113 →
SCHEMATIC DIAGRAM Voltage Detector2

Thermal Thermal protection 138

THM
D

Detector /ICTI Reset for DSP

14

/CSTI 17 Chip Select for DSP

IC44
MUTETI DSP Mute Control
33
DSP
/SPIRDY 28 SPI Ready from DSP
/INTTI 26
Interrupt from DSP
D4015
IR LED
U401 Remote In 104 REM
IC64 2ch DAC
OPERATION (1) IR Receiver CSDAC Chipp Select for DAC
18
IC65 8ch DAC
• See page 112 → 115 117
SW417 Pulse from Rotary Encoder VRA, VRB
SCHEMATIC DIAGRAM Volume /ICADC ADC ON/OFF IC66
11
111 112
SW410 Pulse from Rotary Encoder ISA, ISB 2ch ADC
Input Selector
113 114
SW411 Pulse from Rotary Encoder TONEA, TONEB /AUP_MT Audio Upconversion Mute Control IC56
47
E

Program Selector Audio Upconv.

Mute

Reset for FL Driver 110 /RSTFD

IC401 Chip Select for FL Driver 122 /CEFD DPWR 60 DSP Power ON/OFF IC48
FL Driver Serial control (SPI) Regulator

IC107
IC30 Regulator
(J model)
SW426 Interrupt from Power Switch /PSW
Microprocessor
103 (U, C, R, T, K, A, B, G, E, F, L models)
Standby/ON IC106,
Analog Video Power ON/OFF
MAIN ON/OFF Q1100, 1103

VPWR Video power ON/OFF IC20, 80, 81, 305 Regulator

137
SW402-405
Regulator
SCENE1-4

133 134
SW401, 406-409, KEY0, KEY1 Voltage Detect ADKEY0, ADKEY1 MAIN (2)
F

412-416, 418-421 /INT_RT, HDMINT Interrupt from HDMI Rx

54 • See page 113 →
/RES_Rx 52 Reset for HDMI Rx IC17
HDMI
SCHEMATIC DIAGRAM
D4005 Pure Direct LED ON/OFF 109 PDLED Dual Receiver
LED 45 I2C bus(400KHz)
SCLH SII9135
119 120 121
44
D4001-4005 Scene LED ON/OFF SCEN0, SCEN1, SCEN2 SDAH
LED

/AUPH_A 55
HDMI Audio conversion select IC12
JK401 YPAO MIC Detect 124 /MIC Selector
CONTROL SECTION BLOCK DIAGRAM

YPAO MIC

JK431 Head Phone Detect 61 /HP /RES_Tx 53

Reset for HDMI Tx IC10
Head Phone HDMI
Transmitter
SII9134

/AUPH 56
Video Upconversion ON/OFF IC91-93
Bus Buffer
G

FUNCTION (1) 77
IC202 Serial control CKEV
78
• See page 110 → Selector & /ICS Reset for Scaler IC83
DTEV 58
85
SCHEMATIC DIAGRAM IC203 Serial control Scaler
CKEX
Extention 86 ABT1010
DTEX

83 80 81 82 84 79
/MTFS, /MTCT, MTSW, /MTSB, /MTZ2, /MTHP /ICV 67 Reset forVideo DEC/ENC IC82
Audio Mute
Video Decoder
ADV7800
SDTP
Serial Control (UART) SDRP
IC84
HD Radio Tuner
Reset for HD Radio Video Encoder
89 ADV7172
SCKP
90
Serial Control (SPI) SDTP
88 129
SDRP SCKN Serial control (SPI)
H

131 IC85
Chip Select for PLL IC 87 CEP SDTN
OSD
FM/AM Tuner Tuner Mute Control 92 TMT /OSDCE 68 Chip Select for OSD
LC74782JM
Tuned Detection 94 /TUNED
Stereo Detection 95 /ST

27
/HSW_INT Interrupt from CEC u-com
35
HSW_CEC
IC24
/PSENB 50 Reset for CEC u-com
CEC u-com
VIDEO (1) 1
MN103SFD7GYAB
36
Serial Control (UART) TXDi SCLL I2C bus(100KHz)
• See page 114 → 144 37
RXDi SDAL
SCHEMATIC DIAGRAM CB301 iPod Detection 4 iPDET
Dock Connector iPod Accessory Power Detection 141 iPAP Reset for HDMI SW IC16
48
/HSW_RST
Dock ID Detection 128 DKID HDMI SW
I

SII9185A VIDEO (2)

Q3300 Dock Power ON/OFF 123 DKPWR
66
• See page 115 →
Dock Power SW S-Video,Component detect IC86,87
SVDET SCHEMATIC DIAGRAM
72
CPNTD Video Detector
62
IC302,303 VIA
63
CVBS, Y/C CVBS,Y/C input select VIB
64
selector VIC IC392
Component
IC304 Analog Video BYPASS ON/OFF 65
Selector
BYPASS
BYPASS SW NJM1321
69
/MTVR1
70 73
IC332,333 Moniter,DVR,VCR output control /MTVR2 L1,L2,L3 input select IC383,384
LSEL0
71 75
Video driver /MTMON L1,L2,L3
LSEL1

20 22
J

XL30
20MHz
• See page 105-109 →
DIGITAL SCHEMATIC DIAGRAM
RX-V663/HTR-6160/DSP-AX763

89
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

1
■ PRINTED CIRCUIT BOARDS
Ref no. Location Ref no. Location
D301 D6 IC21 F4
R, T, K, A, B, G, E, F, L, J models D309 C6 IC24 F3
DIGITAL INPUT HDMI
DIGITAL P.C.B. (Side A) DIGITAL U, C, R, T, K, A, B, G, E, F, L models
D310 C6 IC30 D6

OUTPUT OPTICAL COAXIAL D311 C6 IC32 C6

DTV/CBL D313 E6 IC41 D3
U, C models
MD/CD-R MD/CD-R DVD DTV/CBL CD DVD
J model J model D314 F6 IC42 C3
SIRIUS XM DVD DVR OUT D316 E6 IC44 E4
(writing port) (writing port) D401 C2 IC45 E3
JK41 CB13 CB12 CB10 D402 C2 IC46 E3
CB41 CB14

2 CB36 D403 C2 IC47 E3

D601 C3 IC48 C3
14 1 D603 D5 IC49 E5

IC52
D608 D3 IC50 D5

No replacement part available. /

8 7
4 5 D609 D3 IC51 D5

IC57
1 12
D611 C5 IC52 E2

IC11
1 8 48 13 4 5
13 24 41 60
12 25 1 3 1
IC41 7 40 61
D800 G6 IC54 D5

IC42
RX-V663 (U, C models)

37 24
36 25 IC56 8 26 50
D805 G6 IC55 E3

IC16
HTR-6160 (U model)

37 36 14 65 96 25 51
1
48 64 97
D806 G6 IC56 E3

IC10
IC24 21 80
20 1 D820 G6 IC57 C2
9 16 9 16 9 16
IC10 H3 IC61 D3
COM
1 75
3 5 1 IC55 IC45 IC46
33
1 128
100 76
IC11 H2 IC62 E3
IC48

32
IN

OUT 1 4 16 1 8
4 3 IC63 IC72 8 1 8 1 1
1 10
IC12 H3 IC63 C3
8 5 37 72
8 9
OPERATION (4) 9 8 36 73
1 4
IC13 H3 IC64 D4

IC62
5 1 IC13 IC12
(W442) 10 11 4 6 IC16 G3 IC65 D4

IC19
FUNCTION (1) 5 8 1 16
IC47 20 11 8 5

IC66
(CB205) 3 1
4 3 IC17 G3 IC66 D3

IC17
IC67
4 1
1 20 IC19 F3 IC67 C3
+5D IC20
CB46

-12 DGND 5 8
+12T IC20 F4 IC68 C4
+12 AXD 109 144
4 1
MIC 5 1 1 108
FUNCTION (3)

IC21
1
E 108
144 109
XML 4 3 (W2501)
XMR 1 4 16 1
SRE
SRL
IC64
SRR IC68 13 24 DACVBS
E +5V

IC44
ADL 12 25
ADR 8 5 9 8 DASC
4 4 5 -5V
CB61

IC89
E IC84 DASY
FL 1 8 +9V
FR 1 36 ADCVBS
E PRV2 48 37 S10 VE
C +12 PRY ADSC
SW VE

CB33
E -12 1 73 72 36 MG ADSY
SL 28 VE
SR +5D 37 1 10 1 10 1 10 PDET TXDI VIDEO (1)
CB62

E 1 4 IC93 IC92 IC91

RXDI
IC65

+3.3D +5M

CB80
SBL IC69
IPAP (CB305)
SBR XMPWR 8 5 20 11 20 11 20 11
1 44 /RES IPDET
+5.3X 176 45 DKID
25 48 VPWR
AVPWR 15 14 28 54 /MTMON
THM /MTVR2
/MTVR1
BYPASS
VIC
U, C models

IC49
8 1 11 20 1 10 VIB
VIA

IC51
8 1
IC71

IC82 DKPWR
IC70

MAIN (2) 5 4
5 4 IC54
(W107) IC50 27 1
10 1 20 11

24 1
OPERATION (1) 133 88
5 (W401)
132 89

+12
-12
CB63

E
MIC 1 36 37

CB81
144
13 24
IC85
• Semiconductor Location 12 1

7 8 7 8

IC86

IC87
Ref no. Location Ref no. Location IC30
14 Ref no. Location Ref no. Location
1 1 14
IC32
D108 H2 D138 F2 4 5
IC69 C4 Q107 F3
D109 H2 D139 G2 3 6 1 IC70 D5 Q300 C6
1 109 72
108 73
D110 H2 D140 G2 IC71 C5 Q305 E6

IC80
CB38

6 D112 H2 D141 F2 4 3
1 3
IC72 C3 Q306 E6
D126 G2 D142 F2 IC80 H6 Q307 E6
DPWR
DPWR

CB30 CB31 CB34 IC99

CB32
6 4
D127 G2 D143 F2 CB82 IC82 G5 Q308 E6
D128 G2 D144 F2 IC84 H4 Q309 F6
/ST
TMT
CLKRDS
RSTRDS
SCKP
CEP
CKEX
MG
MTZ2
MTSB
MTSW
MTHP
SCKN
/CEFD
SCEN2
SCEN0
ADKEY0
VRA
TONEA
ISA
PDLED
/PSW
RM-
+5M
MG

PRD
PRI
PLDET
LC
RMSCN

TRIG
RM+
RM-
-VP
SP_IMP
PRV1
SPA
SPB
SPC
SBRY
Z2RY

+5HV
+5HV
HGND
VGND
VGND
D129 G2 D145 F2 MAIN (2) J model IC85 G5 Q310 F6
ADY
D130 G2 D146 F2 (W113) VE IC86 H6 Q311 F6
J model MAIN (2) VE
ADCb
/TUNED
RXDRDS
RDYRDS
SDRP
SDTP
DTEX
DTEV
CKEV
MTFS
MTSBJ
MTCT
/HP

(W109) ADCr
SDTN
SCEN3
SCEN1
ADKEY1
VRB
TONEB
ISB
/RSTFD
REM
/MIC
RM+
+5D
-VP

D131 G2 D147 F2 VE IC87 H6 Q401 D2

DAY
RX-V663 (U, C, R, T, K, A, G, E, F, L models) VE
D132 G2 D148 F2 VE
DACb IC89 G4 Q402 D2
HTR-6160 (U, F models)
MAIN (1) MAIN (1) DACr
D133 G2 D149 F2 VE IC91 G4 Q601 C5
OPERATION (1) (W104) (W103) LSEL1
FUNCTION (1) LSEL0
D134 G2 D150 F3 (CB401) SCLL IC92 F4 Q602 C5
(CB206) SDAL
D135 G2 D152 F3 IC93 F4 Q603 C5
7
D136 G2 D159 F4 U, C, R, T, K, A, B, G, E, F, L, J models C, R, T, K, A, G, E, F, L, J models VIDEO (2) IC99 I6 Q604 C5
D137 G2 D160 F3 (CB356) Q105 F3 Q800 G5

90
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

DIGITAL P.C.B. (Side B)

U, C models R, T, K, A, B, G, E, F, L, J models J model

RX-V663 (U, C models)

HTR-6160 (U model)

5 R, T, K, A, B, G, E, F, L, J models • Semiconductor Location

U, C models Ref no. Location Ref no. Location
D111 H2 D610 D3
D153 F4 D801 H5
D154 F4 D802 H5
D156 F4 D803 H5
D162 F4 D804 H5
R model
D300 C6 D807 G5
D302 D6 D809 H6
D303 D5 D811 G5
6 D304 D5 D814 H6
D305 D6 Q102 F2
D306 C6 Q103 F2
D307 C6 Q104 F2
HTR-6160 J model G, E, F models RX-V663 (U, C, R, T, K, A, G, E, F, L models) J model D312 C5 Q106 F2
HTR-6160 (U, F models) D317 D5 Q108 F4
C, R, T, K, A, G, E, F, L, J models U, C, R, T, K, A, B, G, E, F, L models D318 D5 Q109 F4
D409 E3 Q110 F6
D411 C3 Q111 F6
D604 D5 Q301 C5
D605 C5 Q304 E6
7
D606 C5 Q313 E5
D607 D4 Q403 C2

91
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

1
RX-V663
HTR-6160 (U, F models)
FUNCTION (1) P.C.B. (Side A)
R, T, K, A, B, G, E, F, L, J models
AUDIO MULTI CH INPUT ZONE 2 PRE OUT
OUT
PHONO CD MD/CD-R DVD DTV/CBL DVR VCR FRONT SURROUND CENTER / FRONT SURROUND SUR. BACK CENTER / SUB-
IN (PLAY) OUT (REC) IN OUT IN OUT (6CH) SUBWOOFER (SINGLE) SUB- WOOFER 2
SB WOOFER 1
L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R (8CH) L / R L/R L/R L/R L/R
2

3 U, C, R, T, K, A, B, G, E, F, L, J models
U, C, R, T, K, A, G, E, F, L, J models
FUNCTION (5)
(W2505)
TUR
TUL

B model
E

CB242

-12
+12T
+12
MIC
E
XML
XMR
SRE
SRL
SRR
E
CB205

ADL
DIGITAL (CB61) E
ADR
FL
FR
E
C
SW
E
5 SR
SL
E
SBL
SBR

G, E, F models
W2503
AXC
AXY
VE
AXV
VE
IPL
E
IPR

CB206 CB231 CB232

VIDEO (1) CB246
(CB302)
CB201 CB221

HPR
+12HP
HRI
E
HLI
-12HP
HPL
AUX-C
AUX-Y
VE
AUX-V
VE
AXL
E
AXR

/HP
HG
HPL
E
HPR

/ST
TMT
CLKRDS
RSTRDS
SCKP
CEP
CKEX
MG
MTZ2
MTSB
MTSW
MTHP

E
-13
+BV
SBRO
SBR+
FRO
FR+

SRO
SR+
CO
C+
SLO
SL+
FLO
FL+
SBLO
SBL+
U, C models
6
FUNCTION (9) MAIN (1) MAIN (1)
(CB247) (W106) (W105)
TUNED
RXDRDS
RDYRDS
SDRP
SDTP
DTEX
DTEV
CKEV
MTFS
MTSBJ
MTCT
/HP

OPERATION (1)
OPERATION (4) (W402)
(W441)
COMP DIGITAL (CB34) • Semiconductor Location
+10B
TUNED
/ST Ref no. Location Ref no. Location Ref no. Location Ref no. Location
TMT
TUL Q2005 G5 Q2306 H5 Q2313 H5 Q2320 J5
TE
TUR
SDRP Q2006 F5 Q2307 I4 Q2314 I5 Q2321 G5
SCKP
SDTP
CEP Q2301 I4 Q2308 I5 Q2315 H5 Q2401 D5
Q2302 H4 Q2309 I5 Q2316 J4 Q2402 D5
TUNER Q2303 I5 Q2310 I4 Q2317 G5 Q2403 D4
7
Q2304 H5 Q2311 H5 Q2318 J4
Q2305 I5 Q2312 I5 Q2319 G5

92
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

FUNCTION (1) P.C.B. (Side B)

2
RX-V663
R, T, K, A, B, G, E, F, L, J models U, C models HTR-6160 (U, F models)

4 1
3
IC225

5 8
4 1

IC226

5 8 8 5
51 50
U, C, R, T, K, A, G, E, F, L, J models IC227

1 4
31
32 17
30

2
IC203

20
1 16 80

IC
81
4

100 1

8 IC241 1
5
9 16

G, E, F models RX-V663 (U, C models) R, T, K, A, B, G, E, F, L, J models U, C models

6 HTR-6160 (U model)

• Semiconductor Location
Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location
D2001 F5 D2402 C4 Q2002 G3 Q2201 F5 Q2256 H3 Q2263 H3
D2002 F5 IC202 E4 Q2003 H3 Q2202 F5 Q2257 H4 Q2264 H3
D2201 F6 IC225 G3 Q2004 H3 Q2251 H3 Q2258 H3 Q2507 I3
D2202 F6 IC226 G3 Q2007 H3 Q2252 H3 Q2259 H3 Q2508 I3
D2301 I5 IC227 I4 Q2008 H3 Q2253 H3 Q2260 I3
7
D2302 G5 IC241 C5 Q2009 H3 Q2254 I3 Q2261 I3
D2401 C5 Q2001 G3 Q2010 H3 Q2255 I3 Q2262 H4

93
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

FUNCTION (3) P.C.B. (Side A) FUNCTION (3) P.C.B. (Side B)

U, C, R, T, A, B, G, E, F, L, J models

AC OUTLTE(S)
K model

RX-V663 (U, C models)

HTR-6160 (U model)

POWER TRANSFORMER

RX-V663 (U, C models)

3

CB257

HTR-6160 (U model)
J model
CB258

CB254

CB256
U, C, R, T, A, B, G, E, F, L models
CB255

CB253
U, C, R, T, K, A, B, G, E, F, L models
4
AC IN

J model
FUNCTION (2) (W2502A, W2502B)
S10
W2501

PRY
MG RX-V663 (U, C models)
PDET HTR-6160 (U model)
+5M
/RES
1 7
5
DIGITAL
(CB33) IC253
IC252
14 8
IC251
+11H
HGND
R, T, K, A, B, G, E, F, L, J models
HGND 1
5
HGND B2
C

MAIN (2)
(W108)
6
AC_HDMI
CB252

NC
AC_HDMI

POWER TRANSFORMER RX-V663 (U, C models) T, K, A, B, G, E, F, L, J models R, T, K, A, B, G, E, F, L, J models

HTR-6160 (U model)
• Semiconductor Location
Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location
D2501 G5 D2505 G5 D2509 G5 D2514 B3 IC252 D5 Q2503 B5
D2502 D6 D2506 H5 D2511 G5 D2515 G3 IC253 C5 Q2504 D5 RX-V663 RX-V663/HTR-6160/DSP-AX763
7 Circuit No.
D2503 G5 D2507 H5 D2512 D4 D2516 G3 Q2501 G5 Q2509 G5 C U, C, R, T, K, A, B, G, E, F, L, J
D2504 G5 D2508 H5 D2513 G5 IC251 C5 Q2502 B5 Q2510 G5 J2945, 2951 O X

94
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

FUNCTION (2) P.C.B. (Side A) FUNCTION (4) P.C.B. (Side A) FUNCTION (5) P.C.B. (Side A) FUNCTION (5) P.C.B. (Side B)
J model R, L models B model B model

POWER TRANSFORMER
TUNER
AC IN L/R
2

WH
OR

GY
RE
YE

BE

BE
VI
W2601B

CB262

CB261

W2505
3

CB264
W2502A
W2502B

TUR
W2601A
FUNCTION (1) TE

CB263
(CB243)

R model
TUL
BE

WH

WH
L model VOLTAGE VOLTAGE SELECTOR
4 SELECTOR
POWER TRANSFORMER 230-240V 1-2/5-6
FUNCTION (3)
(CB253) 220V 2-3/6-7
110V 3-4/7-8
120V 4-5/8-1

FUNCTION (6) P.C.B. (Side A) FUNCTION (6) P.C.B. (Side B) FUNCTION (9) P.C.B. (Side A) FUNCTION (9) P.C.B. (Side B)

HPL
S2DET -12HP 8 5
/MTMON HLI IC220

CB247
CB296

+5V E 1 4
-5V HRI
+9V S2DET +12HP
/MTMON HPR
CB297

+5V
6 VIDEO (1) -5V
(CB304) +9V FUNCTION (1)
(CB246)

VIDEO (2)
(CB355)

• Semiconductor Location
7
Ref no. Location
IC220 H6

95
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

OPERATION (1) P.C.B. (Side A)

RX-V663
HTR-6160 (U, F models) B model
SCKN
SDTN
/CEFD
NC
SCEN2
SCEN1
SCEN0
ADKEY1
ADKEY0
VRB F2
VRA
CB401

TONEB F1

W403
TONEA SYSW
ISB
ISA MG
/RSTFD MASW
3 REM
PDLED
/PSW
/MIC
RM-
RM+ OPERATION (2)
+5M
+5D (CB421)
MG
VP

DIGITAL (CB30)

SPEAKERS

OPERATION (5)
4
ZONE ZONE 2 INFO MEMORY CATEGORY BAND EDIT SPEAKERS
CONTROL ON/OFF A/B/C/D/E BEARCH MODE
W402 PRESET/TUNING/CH
/HP
NC
HPL
HPE
HPR

W401
FUNCTION (1)
(CB221)
/HP

W404
HPL
HPE
HPR
4 3 2 1
5 OPERATION (3)
SCENE (CB431)

AUDIO SELECT
STRAIGHT TONE CONTROL
JK401
PURE DIRECT
OPTIMIZER MIC INPUT PROGRAM

EFFECT
6
+12
-12
E
MIC

DIGITAL (CB63)

• Semiconductor Location
Ref no. Location Ref no. Location Ref no. Location
7 D4001 H4 D4003 F4 D4005 F5 Circuit No. U, C, R, T, K, A, G, E, L, J B
D4002 G4 D4004 E4 D4015 D3 SW401, 406, 409, 413-416, 418, 419, 421 O X

96
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

OPERATION (1) P.C.B. (Side B)

2
HTR-6160 (U, F models) U, C, R, T, K, A, G, E, F, L, J models

33 32

1
48 17

40
3

IC
49 16

64 1

HTR-6160 (U, F models)

4 1
5
IC402

5 8

6
• Semiconductor Location
Ref no. Location Ref no. Location Ref no. Location Ref no. Location
D4008 D4 D4018 D5 Q4007 F3 Q4017 G5
D4009 H5 IC401 G3 Q4008 E4 Q4018 F5
D4010 F5 IC402 D5 Q4009 F3 Q4019 H3
D4011 G5 Q4001 H4 Q4010 F3 Q4020 G3
D4012 E5 Q4002 H4 Q4011 F5 Q4021 G3
D4013 H3 Q4003 H4 Q4012 E5 Q4022 G3
D4014 H3 Q4004 F4 Q4014 D4
7 D4016 D6 Q4005 H4 Q4015 H5
D4017 D6 Q4006 F4 Q4016 F5

97
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

OPERATION (2) P.C.B. (Side A) OPERATION (2) P.C.B. (Side B)

OPERATION (1)
(W403)

MASW

SYSW
POWER TRANSFORMER

MG

F1
F2
2

F1

F2
CB421

CB422

3
(U, F models)
HTR-6160
RX-V663

SYSTEM
OFF
MAIN ZONE RX-V663
ON/OFF HTR-6160 (U, F models)

STANDBY
ON/OFF

HTR-6160 (C model)
DSP-AX763

OPERATION (3) P.C.B. (Side A) OPERATION (3) P.C.B. (Side B)

PHONES
SILENT CINEMA

JK431

/HP
CB431

HPL
HPE
HPR • Semiconductor Location
Ref no. Location
OPERATION (1) D4301 H6
7 (W404)
D4302 H5
D4303 H5

98
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

OPERATION (4) P.C.B. (Side A) OPERATION (4) P.C.B. (Side B)

DIGITAL (CB46)
2 FUNCTION (1)
(CB201)

AUX-C
AUX-Y

AUX-V
AXD

AXR
AXL
+5D
DG

VE

VE

E
W442

W441

IC441
3

J model
JK441

U, C, R, T, K, A, B, G, E, F, L models

4
R L
OPTICAL AUDIO VIDEO S VIDEO
VIDEO AUX

5 OPERATION (5) P.C.B. (Side A)

OPERATION (1)

• Semiconductor Location
Ref no. Location
D4401 I3
D4402 I3
VOLUME
D4403 H3
7
D4404 H3
IC441 G3

99
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

MAIN (1) P.C.B. (Side A) SPEAKERS

FRONT B/ZONE B/
FRONT A CENTER SURROUND SURROUND BACK/BI-AMP
• Semiconductor Location ZONE 2/PRESENCE
R L R L R L R L (SINGLE)
Ref no. Location Ref no. Location Ref no. Location Ref no. Location
+/- +/- +/- +/- +/- +/- +/- +/- +/-
D1000 C5 D1029 E4 D1065 D4 Q1026 I6 RX-V663
HTR-6160 (U, F models)
D1001 H4 D1030 E4 D1066 F4 Q1027 H6
D1002 H4 D1031 D3 D1067 C3 Q1028 G6
TRIGGER
2 D1003 C5 D1032 H3 D1068 C3 Q1029 F6 REMOTE
OUT
D1004 I6 D1033 C3 D1069 C2 Q1030 E6 IN OUT
D1005 I6 D1034 D3 Q1000 C5 Q1031 C5
D1006 H6 D1035 I5 Q1001 E4 Q1032 D5

POWER TRANSFORMER
D1007 H6 D1036 I5 Q1002 E4 Q1033 I7 JK100 JK201 JK102

D1008 G6 D1037 E4 Q1003 E4 Q1034 I7

BL
D1009 G6 D1038 E4 Q1004 D4 Q1035 I6
D1010 F6 D1039 I3 Q1005 E4 Q1036 H6 W111B

to W111A
D1011 F6 D1040 H3 Q1006 H2 Q1037 H6
D1012 E6 D1043 E4 Q1007 D4 Q1038 G7
D1013 E6 D1044 H4 Q1008 E4 Q1039 G6
3
D1014 E6 D1045 H4 Q1009 E4 Q1040 F6 BL W111A
to W111B
D1015 E6 D1047 D4 Q1010 E4 Q1041 F6
D1016 D5 D1048 I5 Q1011 D4 Q1042 E6
D1017 D7 D1049 D4 Q1012 E4 Q1043 E6 AC_BH
AC_BH
D1018 H6 D1050 H5 Q1013 H3 Q1044 D6
E

CB100
D1019 I6 D1053 I6 Q1014 D4 Q1045 C5
E
D1020 H6 D1054 I6 Q1015 C3 Q1046 D5
AC_BL
D1021 G6 D1055 H6 Q1016 C3 Q1047 C5
AC_BL
D1022 F6 D1056 G6 Q1019 I7 Q1048A I7
D1023 E6 D1057 F6 Q1020 H7 Q1048C I7
4 D1024 D6 D1058 E6 Q1021 G7 Q1049A H7 W112C
BE
W112A
RE to W112B

D1025 D4 D1061 D6 Q1022 F7 Q1049C H7

to W112D
D1026 F4 D1062 D6 Q1023 E7 Q1050A G7
D1027 D4 D1063 D6 Q1024 D7 Q1050C H7 W100A

D1028 E4 D1064 C6 Q1025 I6 Q1051A F7

+18
E
-18
PRV1
+10
E
-10
+IPOD
E
E
+12
-12
DIGITAL (CB31) DIGITAL (CB32)
SP_IMP

RMSCN
PLDET
SBRY

AC_I
PRV1

Z2RY
TRIG
RM+

PRD
SPC
SPB
RM-

SPA

MAIN (2)
-VP

PRI

AC_I
LC

5 W103 W104
NC (W100B)
AC_5
E

CB101
AC_5
NC
AC_12
E
AC_12
W106 W105

POWER TRANSFORMER
E
-13
+BV
SBRO
SBR+
FRO
FR+

SRO
SR+
CO
C+
SLO
SL+
FLO
FL+
SBLO
SBL+

6
FUNCTION (1) FUNCTION (1)
(CB231) (CB232)

W112B

BEW112D
Ref no. Location Ref no. Location Ref no. Location Ref no. Location
RE
Q1051C G7 Q1061 H6 Q1067 F4 Q1079 D6
Q1052A E7 Q1062 G6 Q1068 H3 Q1080 C6
Q1052C F7 Q1063 F6 Q1069 D3 Q1081A C7
Q1053A D7 Q1064 E6 Q1070 D3 Q1081C D7
7
Q1053C E7 Q1065 D6 Q1077 C7 Q1083 C6 to W112C
Q1060 I6 Q1066 I6 Q1078 D6

100
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

MAIN (2) P.C.B. (Side A)

FUNCTION (3)
DIGITAL (CB62) (CB251) MAIN (1) VIDEO (1)
DIGITAL (CB82) (W100A) (CB303)
DIGITAL (CB38)

XMPWR
J model

+IPOD
DPWR
DPWR

VPWR

HGND

HGND
VGND
VGND

VGND
VGND
+3.3D
+5.3X

PRV1
PRV2

+5HV
+5HV

IGND
+11H
THM

+5D
U, C models

+5V
+10

+12
+12

+18

+12

-5V
-10

-12
-12

-18

-12
+5I
E

E
E
E

E
W113 W107 W114
W100B

W108
W109
4

GND
VCO
OUT
IC101
IC102 IC107 IC106 IC110 IC100 IC105 IC104
1 4 1 4 1 4 1 4

IN
COM
OUT

IN
COM
OUT

IN
COM
OUT
U, C models

6
• Semiconductor Location
Ref no. Location Ref no. Location
D1051 E4 IC107 D4
D1052 E4 IC110 E4
D1070 F4 Q1100 G4
IC100 E4 Q1101 H4
IC101 D4 Q1102 H4
IC102 D4 Q1103 H4
IC104 G4 Q1104 F4
7 IC105 F4 Q1105 F4
IC106 E4

101
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

VIDEO (1) P.C.B. (Side A) VIDEO (1) P.C.B. (Side B)

2
FUNCTION (6)
(CB296)

/MTMON
S2DET

+5V

+9V
-5V
CB304
MONITOR
OUT

1
3
19 36 19 36 MAIN (2)

IC305
JK303
OUT

(W114)
IC333 IC332
4
18 1
VCR

+5I
18 1
IGND
+12

CB303
E
-12V
IN

+5V
-5V
J model

U, C, R, T, K, A, B, G, E, F, L models
16 1
4
OUT
VIDEO

1
16
IC304
IC303
DVR

JK302

9 8
9 8

DACVBS
+5V
IN

DASC
-5V
16 1 DASY
+9V
ADCVBS
VE
IC302

ADSC
VE
DTV/CBL

ADSY
9 8 VE
CB305
VIDEO / S VIDEO

TXDI J model
5 RXDI
IPAP
IPDET
DKID
VPWR
JK301

16 1 /MTMON
/MTVR2
/MTVR1

U, C, R, T, K, A, B, G, E, F, L models
IC301

BYPASS
VIC
DVD

VIB
VIA
9 8 DKPWR
No replacement part available.

DIGITAL (CB80)
IPR
E
IPL
CB302

VE
6 5 8
AXV
DOCK

CB301

IC331 VE
4 1 AXY • Semiconductor Location
AXC
Ref no. Location Ref no. Location
D3002 C6 IC333 C3
FUNCTION (1)
(W2503) D3003 B6 Q3001 C5
J model IC301 C5 Q3002 C4
IC302 C5 Q3003 C5
IC303 C4 Q3004 D5
IC304 D4 Q3005 D5
IC305 D3 Q3006 D5
7
IC331 C6 Q3300 D6
IC332 C3 Q3301 D6

102
 A B C D E F G H I J
RX-V663/HTR-6160/DSP-AX763

VIDEO (2) P.C.B. (Side A) VIDEO (2) P.C.B. (Side B)

U, C, R, T, K, A, B, G, E, F, L models

2 DVD

CB351
DTV/CBL

ADY
VE
1 8 ADPb
CB352

VE
ADPr
IC383 VE
D5 VIDEO

DAY
3

CB356
16 9 VE
DAPb
VE
DAPr
VE
LSEL1
CB353
DVR

LSEL0
SCLL
SDAL

DIGITAL (CB81)
MONITOR
OUT

CB354

9 16
IC351
J model

8 1
J model

4
PR/PB/Y
MONITOR OUT
PR/PB/Y
DVD /

15 24
14 25
5
PR/PB/Y
COMPONENT VIDEO

IC392

1 38
48 39
PR/PB/Y
DTV/CBL /

PR/PB/Y
DVR

• Semiconductor Location
PR/PB/Y

Ref no. Location

D3502 C3
D3504 C3
D3506 C2
CB355
D3510 C4
S2DET
/MTMON
+5V
-5V
+9V

IC351 C4
IC383 C3
7
IC392 C5
FUNCTION (6)
(CB297) Q3501 C4

103
 RX-V663/HTR-6160/DSP-AX763

MEMO MEMO

MEMO MEMO
104
 A B C D E F G H I J K L M N

RX-V663/HTR-6160/DSP-AX763
SCHEMATIC DIAGRAMS
DIGITAL 1/5
1
HDMI
DTV/CBL (U, C, R, T, K, A, B, G, E, F, L models)
OUT DVD IC10: SiI9134CTU
DVR (J model)
DSP-AX763 RX-V663/HTR-6160 RX-V663 DSP-AX763 RX-V663/HTR-6160 RX-V663 HDMI transmitter
CB10 CB12 CB13 INT HPD

RESET#
CSDA CI2CA
CSCL E-DDC DSCL
Slave
Registers Master DSDA
VSYNC and
Video Configuration HDCP
HSYNC Data Encryption HDCP Keys
IDCK Logic EEPROM
Capture Engine
DE Logic/DE
D[35:0] Generator EXT_SWING

YCbCr to RGB
Color Space XOR Tx0
HDMI 1.3 Tx1
S/PDIF Converter/ Mask TMDS
MCLK 4:2:2 to 4:4:4 Tx2
Core TxC
WS Audio Converter

2 SCK
SD[3:0]
DL[3:0]
Capture
Logic
DR[3:0]

IC13: SN74LVC245APWR
Octal bus transceivers with 3-state outputs
DIR 1 20 Vcc
0 0 0 0 0 0 0 0

0 0 0 0 A1 2 19 OE

A2 3 18 B1

A3 4 17 B2
0.4
0.4

0.4
0.4

0.4

0
0
3.3 (J model) A4 5 16 B3

3.3
A5 6 15 B4
0 0

3 4.9 4.9
A6 7 14 B5

A7 8 13 B6

0 3.3
A8 9 12 B7

3.3
3.3
3.3

3.3
3.3
3.3
3.3

3.3
0

0
0

0
0

0
0
3.3

3.3
GND 10 11 B8
1.8
1.8

3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3

3.3
3.3
3.3
3.3
3.3 3.3
3.3 3.3

3.3 3.3

0 0.2 0.2 0 0 3.4 3.4 0

0
3.3
3.3
CEC 3.3
3.3
0 0 0 0 0
3.3
3.3
IC16: SiI9185ACTU
0

0
0.2

0.2
0.2

0.2
0

0
0 0 0
0

0
3.4

3.4
3.4

3.4
0

0
0 0 0
3.3

3.3
MICROPROCESSOR 3.3
0
3.3
HDMI switch

Port0_DDC
Port1_DDC
Port2_DDC
3.3

EPSEL1/

EPSEL0/

TX_DDC
0 0.2 0.2 0 0 3.4 3.4 0 0
3.3

LSDA
LSCL
0 3.3
0
3.3
3.3
3.3 EDID Block
1.8 3.3

Termination/
R0X0+/- Config. EDID

Equalizer
0 3.3 Logic I2C Switch
R0X1+/- RAM
3.3
0
A-2 IC24
3.3 R0X2+/-
3.3 R0XC+/- Configuration Block
4 1.7
1.6
3.3
3.3
Transmitter
Block

Termination/

Oversample
R1X0+/-

Equalizer
3.3 3.3
TX0+/-

DPLL
3.3 R1X1+/-
3.3 R1X2+/- TX1+/-
3.3 3.3
R1XC+/- Transmit TX2+/-
3.3 Drivers
3.3
3.3

Termination/
3.3 R2X0+/-

Equalizer
3.3
3.3
PLL TXC+/-
R2X1+/-
3.3
3.3 R2X2+/-
3.3 3.3 R2XC+/- 5V Switch HPD

CEC
Switch CEC I/F
3.3 3.3
3.3 3.3 Receiver Block
3.3

3.3
3.3
3.3

RPWR0
RPWR1
RPWR2
I2CADDR/
TPWR
HPD0
HPD1
HPD2
HPDIN

CEC_A

CEC_D
3.3
3.3

3.3
0
0

0
0
0

0
0

0
0
0

0
3.3

0
0
0
0

3.3
0

0
0.2
0.2
1.9

3.4
3.3
4.2

1.9
0.2
0.2

0.2
0.2
3.4
0.2
0.2
0

0
0
0

0
0

0
0

0
3.3
3.3
0.4
0.4
0
0.2
IC17: SiI9135CTU
3.4 0.2 HDMI receiver
0.4 1.9
0.4 0 INT XTAL
0 3.3 3.3

5 0.4
0.4
IC16 0

1.9
3.5 3.3 RESET#
Registers & HDCP
1.9 0 CB14 (Writing port) CSDA I2C Configuration Keys MCLK
3.3 CSCL Logic ROM MCLKOUT
1.9 0 Gen
1.9 0 4.2 DSDA0
3.3 DSCL0 I2C
0.4 1.9
1.9 3.4 4.2 SPDIF
3.3 HDCP Audio DSD
0 3.4 Rx0± HDMI1.3
Rx1± Decryption Decode SD[3-0]
0 0 TMDS
HDMI Rx2± Engine Logic SCK
0 3.4 Core 0 WS
RxC±
4.9 5.0 3.3 3.4 MUTE OUT
Digital
3.3 3.4 MUX
0
0
SWITCHER 3.4
3.4
Rx0±
Rx1±
Rx2±
HDMI1.3
TMDS
RGB to YCbCr
Color Space
Q[36:0]
VSYNC

3.3
3.3
HSYNC
IC11 RxC± Core 1 XOR Converter/
ODCK
Mask 4:2:2 to 4:4:4
3.3 3.3 DE
8.7 Converter
9.0 DSDA1 (12-bit Accurate) SCDT
0 I2C EVNODD
5.0 3.3 DSCL1

3.4
3.4
0
3.4
3.4
1.9
3.3
3.3
0
3.3
3.3

0
1.9
3.4
3.4
0
1.9
4.9
5.0
to DIGITAL 5/5
4.4 3.3 4.4

IC19: R1172H181B-T1-F
Voltage regulator
6
No replacement part available.
VDD 4 5 VOUT

Vref
3.3 4.9
Current Limit
to DIGITAL 2/5
CE 1 2 GND

3.3 4.8

3.3
Pin No. Symbol Description
3.3 1 CE Chip Enable Pin
3.3
2 GND Ground Pin
0 0
3 NC No Connection

7
4.9

4 VDD Input Pin

3.4
3.4
3.4

3.4
3.4
3.4

3.3
3.3
3.4

3.3
3.3
3.4

1.8

3.4

3.4

3.4

3.4
1.8
3.3 0
0

0
1.8
1.8
3.4

1.8

1.8
0.3
3.2
3.3
4.9
4.9

1.8

0.3
0.3

0.3
0.3

0.3
0.3

1.8

5 VOUT Output Pin of Voltage Regulator

0

0
0
0

0 0

0 4.9 3.4 0
0 3.3 0 3.4
0 3.4
3.4

1.8
3.3
0

HDMI 0
0
0
0
0
0

0
3.4

IC20: R1232D181A-TR-F
3.3
3.3 TRANSMITTER 0
0
0
1.8
0
0
HDMI DUAL RECEIVER 3.3
3.3
3.3
to DIGITAL 5/5 DC-DC converter
VDD AGND
3.3
3.3 0 0 3.2
3 7
3.3
3.3
IC10 0
3.3
0
0
1.8
1.8
3.3 0 0 IC17 0 VIN 2
1.8
0 0
0
1.8
SELECTOR 0
3.4
0
3.3
3.1
0
Current Limit

3.4 Slope Compensation

3.3 0 0 2.6 5 VOUT
3.3 0 1.8 3.3
to DIGITAL 3/5
Phase Compensation
3.3 0 1.8 0 Lx 8
3.3
3.3
0
0
0
3.3
A-1 1.3
1.2
Q R
Vref
Output Control S PWM Comparator
8 3.3
3.3
0
3.3
3.0
3.3
1.3
1.3
Error Amplifier
4 CE
3.3

3.3 3.1 3.3 1.8 Soft Start

0
0
0
0
0
0
0

Oscillator "H" Active

3.4

1.8

3.3 2.6 0
0 1.3
4.9 1.4 UVLO
IC12
1.3 TEST CKT Chip Enable
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
0

3.3
1.4
1.3
1.4
1.3
1.3
1.3
1.2
1.3

0
1.7

3.3 1.4
1.8

0
No replacement part available. 3.4
0
0
0
0
0
0
0

1 6
5.0

3.3 1.7
"L" Fixed
0 0
0 3.3
PGND TEST
1.8 3.3 1.9 3.3
3.3 3.3 3.3 3.4

1.9

3.3

3.3

4.2
4.2 4.9
3.3

3.3
0

3.3
3.2
3.2
0

3.3
3.3
3.3
3.3
0
1.8
3.3
3.3

3.3
3.3
0
3.3

3.3
3.3
3.3
3.3
0
1.8
3.3
3.3

3.3
3.3
0

3.3
3.3
3.3
3.3
0
0
0
0
0
0
0
0
0

3.3

IC21
IC21: R1172H331D-T1-F
1.8

1.9
3.3

3.3

IC19

3.3
Voltage regulator
IC13

No replacement part available.

0
4.2
0
0
0
0
0
0
0
0
0

3.3

VDD 4 5 VOUT
4.9

9 1.8
1.8 4.9
0 4.9

IC20
0 4.9
1.8 0
1.8 Vref

BUFFER 0
CE 1
Current Limit
2 GND

Pin No. Symbol Description

1 CE Chip Enable Pin
POINT A-1 XL10 (Pin 95 of IC17) POINT A-2 XL12 (Pin 83 of IC24) to DIGITAL 5/5 2 GND Ground Pin
3 NC No Connection
IC24: MN103SFD7G 4 VDD Input Pin
5 VOUT Output Pin of Voltage Regulator
Microprocessor
IC11: NJM2867F3-05 IC12: TC74VHC157FT
Low dropout voltage regulator Quad 2-channel multiplexer
10 SELECT 1 16 Vcc 32 bit Built-in ROM
VIN 5 Microprocessor
4 VOUT 1A 2 ASG 15 ST Bus
1B 3 B A 14 4A Controller
Control 1 Thermal
Protection
1Y 4 Y B 13 4B ★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
2A 5 12 4Y
★ Components having special characteristics are marked s and must be replaced
A Y Extended
Bandgap 2B 6 11 3A computing Built-in RAM
B A element
Reference
2Y 7 YYB 10 3B with parts having specifications equal to those originally installed.
GND 8 9 3Y
★ Schematic diagram is subject to change without notice.
I/O Other Interrupt DMA
Serial peripheral Clock
Timer port Controller
GND 2 I/F equipment control &
System control
WDT

105
 A B C D E F G H I J K L M N
RX-V663/HTR-6160/DSP-AX763

1
DIGITAL 2/5
Page 113 K10
Page 112 G9 Page 113 H4 Page 113 H4 Page 111 B7 to MAIN (2)_W113 Page 110 B8
(J model) POINT A-3 XL30 (Pin 20 of IC30)
to OPERATION (1)_CB401 to MAIN (1)_W103 to MAIN (1)_W104 to FUNCTION (3)_W2501 to FUNCTION (1)_CB206

CB38
CB31

CB32
CB30

CB33

CB34
12.2

C-2 12.2
2 1 IC32
12.5
2 C-3
0
12.5 5.8 5.2
12.5 5.2 5.1

5.2 5.1
5.8

5.8 5.0

5.1 5.2 POINT C-2 C-3 1 / CB33 (+5M), 2 / CB33 (/RES)

4.9

CB33 (+5M) 1 CB33 (+5M) 1

3 3.4

5.1 2.9 CB33 (/RES) 2 CB33 (/RES) 2

5.1

4.5 5.1

Power cable ON Power cable ON

Power cable OFF
5.1

to DIGITAL 5/5
4.9 -6.1
0 0.6

IC30: M30878FJBGP
5.1 Single chip 16/32-bit microprocessor
4
4.9 4.9
-11.4 8 8 8 8 8 8 8
3.8

4.9

5.2

0
0

0
0

5.0
5.2
5.2
4.9
4.9

4.8
4.9
5.1
5.1

4.4
5.0

4.5
4.9
4.9
4.9
4.9
4.5
0
0

0
0

0
0

0
Port P0 Port P1 Port P2 Port P3 Port P4 Port P5 Port P6

5.0
<VCC2> <VCC1>
5.1
Peripheral Functions Clock Generation Circuit
4.9 4.6 A/D Converter:
1 circuit XIN - XOUT
HTR-6160

0 0 4.6 -11.4 Timer (16-bit) Standard: 10 inputs XCIN - XCOUT

Port P7
Timer A: 5-channel Maximum: 34 inputs(2) On-chip Oscillator
5.0 0 Timer B: 6-channel PLL Frequency Synthesizer

8
UART/Clock Synchronous Serial I/O:
5.0 5.0 Three-Phase Motor Control Circuit 7-channel
(3)
DMAC
5.0 5.0

Port P8
Watchdog Timer (15-bit) X/Y Converter: DMACII
5.0 4.9 5.1 16-bit x 16-bit

7
5.0 5.0 D/A Converter: CRC Calculation Circuit (CCITT):

<VCC1>
8-bit x 2-channel CAN Module: 2-channel X16+X12+X5+1
0 4.9

P85
0
0 MICROPROCESSOR 0
-11.4
M32C/80 series microprocessor core
Memory
0 0.2 Intelligent I/O

Port P9
R0H R0L FLG

5 0 5.0 (4) R1H R1L INTB ROM

8
Time Measurement: 8-channel
RX-V663/DSP-AX763

(5) R2 ISP
Wave Generating: 16-channel
0 5.0 5.1 Communication Functions: R3 USP
Clock Synchronous Serial I/O, UART, RAM
0 5.0

Port P10
HDLC Data Processing A0 PC
IC30
0 5.0 4.9 A1 SVF
-11.4

8
FB SVP
4.9 5.0 Multiplier
SB VCT
5.1 0 5.0
<VCC1> <VCC2>

to DIGITAL 1/5
5.0 0
Port P14 Port P15 Port P11 Port P12 Port P13
5.1 5.3 0 5.1
0.7 5.0
5.0 0 4.5 7 8 5 8 8
5.1
5.2 4.9
5.0 4.9 (Note 1)

0 4.9 NOTES:
1. Ports P11 to P15 are provided in the 144-pin package only.
0.3 3.5 2. Included in the 144-pin package only. 26 inputs maximum in the 100-pin package.
3. 6-channel available in the 100-pin package.
5.2 4.9 4. 6-channel available in the 100-pin package.
5.2 5. 10-channel available in the 100-pin package.

6 5.2 0
2.9 4.9
2.3 4.9
5.0 4.8 IC32: R1154H058B-T1-F
1.1 0 Voltage regulator
CB36
0.6 0
0.7 2.9 2.3 0 0 Thermal
Protection
0.5 0
VDD 3 1 VOUT
5.2 A-3 5.0
0 0 0 5.0 3.2
5.1 4.4 4 NC
4.9 4.9 Vref

Short Current
Protection Limit
4.4
5.0
5.0

Circuit Circuit
4.9
4.9
4.7
5.2

0
5.0
5.0
0
5.0
0
4.6
4.9
4.9
4.9
2.6
0
2.4

5.0
5.0

0.8
0
5.0
5.0
5.0
0
0
5.0
0
0

CE 5 2 GND
7 (Writing port)
5.0
5.0
0
0
5.0

Pin No. Symbol Description

1 VOUT Output Pin for Voltage Regulator
2 GND Ground
3 CE Chip Enable Pin (active at "H")
4 NC No Connection
5 VDD Power Supply Pin

DSP-AX763 RX-V663 DSP-AX763 RX-V663 RX-V663 HTR-6160

C332 UR23747 UR26710 UR23747 UR23747 UR23747 UR23747 UR23747 UR23747 UR23747 UR26710 UR26710 UR23747
47/16 10/50 47/16 47/16 47/16 47/16 47/16 47/16 47/16 10/50 10/50 47/16
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter. VT33290 VT33290 VT33290
D300
★ Components having special characteristics are marked s and must be replaced 1SS355 1SS355 1SS355

with parts having specifications equal to those originally installed. to DIGITAL 3/5 R307 RD35622 RD35622 RD35622
2.2K 2.2K 2.2K
★ Schematic diagram is subject to change without notice.
10 R311 RD35510
100
RD35510
100
RD35510
100
RD35510
100
RD35510
100
RD35510
100
RD35510
100
RD35510
100
RD35510
100

106
 A B C D E F G H I J K L M N

RX-V663/HTR-6160/DSP-AX763

DIGITAL 3/5
1
Page 112 H2
to OPERATION (4)_W442

to DIGITAL 2/5

CB46
DSP- DSP- RX-V663/
RX-V663/HTR-6160 RX-V663 RX-V663
AX763 AX763 HTR-6160

1.2 3.0 3.4 4.9

3.0
SIRIUS

1.2
JK41

3.4

4.9
0

IC47
0 0
2 5.0
3.0 IC48

4.9
5.0

0
11.9

0.2
IC57 0.2
REGULATOR
0.2

SELECTOR
0.2 0 3.4
0.2 IC57
0 0 0

IC45
0.2 -11.4 1.7 0
JK41

3 1.7
0 0

0 0
3.4

IC55
1.7 1.7 1.0 0

0 1.7 1.7 0

0 0

5.0

5.0

0.5

5.0

5.0

5.0

5.0
5.0

4.9
5.0

5.0

5.0

5.0
0
0

0
0

0
1.3 0
0 0
0 3.4 0 0
IC54 IC50
0 0 0

IC46
0 0
1.7 0

3.4

0
3.3

3.3
1.6

3.4

0
3.4

0
0

0
0

3.4
0.5

1.0

3.4
3.4

0
XM

3.4
0
CB41

0 0
1.7 0
0
1.7 1.3
1.3
1.3

1.3
1.3

0 1.3
0
3.4

3.4
0

4 0 0

1.5 3.4
0
XM/DT IC
3.4
1.3 0

0 3.4
0 B-1 0
IC42

0
0

3.4
3.4 3.4
3.4
3.4
0
1.7
3.4

3.4
3.3
0

1.7

1.7

0
0

0
1.3

3.3
1.0

3.3
0
0

0
0

0
0
PL/PR

0
0
3.4
1.3
1.3

1.3
1.7

1.7
1.7

1.7

1.2

1.2

3.4

0.2
FL/FR

0
0

0
3.4
0

0
0
(U, C models) C

to DIGITAL 4/5
SL/SR
0 0
SBL/SBR

1.6

1.0
3.4
3.3 0

0 0
0 3.4
0 3.4
ANALOG IN
0

1.2
6 1.2
RX-V663/DSP-AX763

3.3 3.4
3.4
DSP 0
3.4
0
0
0

0 3.4
3.4

5.0
3.3

1.6
1.0

0 0
0

0
HTR-6160

0 3.4
3.4 0
0 3.3 0
3.4
0 3.4 1.2 3.4
0 0 1.6 3.4
4.0 0 0 1.7

0.2 0 3.4 1.2

DIGITAL OUTPUT

0 0 1.2 0

IC44
IC41

DIGITAL IN
3.4
0.2
DIR B-2
1.6
3.4
0
0
0
0
4.5 1.6 0 3.4
0
4.5 3.4 0
1.6 1.2 1.2
5.0
3.4 3.4 1.5 0 3.4
0
7 2.1
3.4

0 0 0 3.4 0
3.3
3.4 0 0 0 0

3.4 3.4 0 0 0 3.4

3.4 No replacement part available. 2.0 0 3.4 0 0

0

4.0
0

1.3

1.4
3.4

1.7

1.7

1.7

0 3.4 0 0 0 3.4
0
0

IC49
3.4 0 0 3.4 0
5.0 0
3.4 3.4 3.4 0 0

IC51
1.2 0 0 0 0 0
3.4 0 0 0 3.4 0

0.2 3.4 0 0 3.4 0 0

OPTICAL

0 3.4 0 0 0
0
0 3.4 0 3.4 0
5.0 0 0 3.4 3.4 3.4
3.4 3.4 0

0
DIGITAL INPUT

3.3 0 3.4 1.8 0

3.4

0
3.4
0
1.2
0
0
0
0
0
3.4
0
0
1.2
0
3.4

3.4

1.8
3.4
1.2
0

0
0
3.4

3.4
1.2
0
0

0
0
0
0
0.2 3.4 3.4 0
0 0 0
IC41: LC89057W-VF4AD-E

3.4
3.4

0 0
3.4 0 0 0 Digital audio interface transceiver
1.7

1.7

1.7

1.4

8 5.0
0

3.4 0 2.0 0
3.4 EMPHA/UO AUDIO/VO INT CL CE CI XMODE
3.4
IC56

IC56

IC56

IC56

0 2.1 0
0 32 33 35 40 39 38 41
1.7 3.4 1.5 0
0

0 2.0 3.4 3.4

0 2.1 0 0
RXOUT 1 Cbit, Ubit Microcontroller
3.4 1.5 3.4 37 DO
IC52 5.0 IC52 0 I/F
3.4 0 1.7 3.4 RX0 2
2.5 2.0 2.0 4.5
36 RERR
COAXIAL

RX1 3
RX2 4
Input Demodulation Data
RX3 5 Selector & 21 RDATA
Selector
RX4 8 Lock detect

IC52 IC52 64M SDRAM 16M FLASH ROM RX5/VI 9

RX6/UI 10 24 SDIN
2.5 2.0 2.0 4.5
16 RMCK
LPF 13 PLL
17 RBCK
IC52 IC52 Clock 20 RLRCK
TMCK/PIO0 44 Selector
0 4.9 0 Modulation 22 SBCK
9 TBCK/PIO1 45
TLRCK/PIO2 46
&
1/N
23 SLRCK
Parallel Port
TDATA/PIO3 47

TXO/PIOEN 48
29 28 27 34
to DIGITAL 1/5 XIN XOUT XMCK CKST

IC47: R1172S121D-E2-F IC48: R1172H331D-T1-F IC55: TC74VHC157FT IC56: TC74VHC08FT IC57: NJM4565M
IC50: TC74VHC541FT IC52: TC74VHCU04FT IC54: TC74VHCT541AFT POINT B-1 XL41 (Pin 28 of IC42) POINT B-2 XL42 (Pin 29 of IC41)
Voltage regulator Voltage regulator Quad 2-channel multiplexer Quad 2-input AND gate Dual operational amplifier
Octal bus buffer Hex inverters Octal bus buffer
SELECT 1 16 Vcc
1A 1 14 Vcc V+
VDD 6 1 VOUT VDD 4 5 VOUT G1 1 20 Vcc 1A 1 14 VCC G1 1 20 Vcc 1A 2 ASG 15 ST
1B 2 13 4B
8
1B 3 14 4A
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
B A
1Y 2 13 6A A1 2 19 G2 1Y 3 12 4A
A1 2 19 G2 1Y 4 Y B 13 4B
2A 3 12 6Y A2 3 18 Y1
2A 5 A Y 12 4Y
2A
2B
4
5
11 4Y
10 3B –INPUT
2, 6
OUTPUT
★ Components having special characteristics are marked s and must be replaced
A2 3 18 Y1 2B 6 B A 11 3A
2Y 4 11 5A
A3 4 17 Y2 2Y 7 YYB 10 3B 2Y 6 9 3A
+INPUT
3, 5
1, 7
with parts having specifications equal to those originally installed.
10 Vref Vref
A3 4 17 Y2
3A 5 10 5Y
A4 5 16 Y3
GND 8 9 3Y GND 7 8 3Y ★ Schematic diagram is subject to change without notice.
Current Limit Current Limit A4 5 16 Y3 3Y 6 9 4A
CE 3 2,5 GND CE 1 2 GND GND 7 8 4Y
A5 6 15 Y4 V–
A5 6 15 Y4 4
A6 7 14 Y5
A6 7 14 Y5
Pin No. Symbol Description Pin No. Symbol Description A7 8 13 Y6

1 VOUT Output Pin of Voltage Regulator 1 CE Chip Enable Pin A7 8 13 Y6

A8 9 12 Y7
2, 5 GND Ground Pin 2 GND Ground Pin
A8 9 12 Y7
3 CE Chip Enable Pin 3 NC No Connection
GND 10 11 Y8
4 NC No Connection 4 VDD Input Pin
GND 10 11 Y8
6 VDD Input Pin 5 VOUT Output Pin of Voltage Regulator

107
 A B C D E F G H I J K L M N
RX-V663/HTR-6160/DSP-AX763

1
DIGITAL 4/5

Page 110 A6 Page 113 K9 Page 112 I9

to FUNCTION (1)_CB205 to MAIN (2)_W107 to OPERATION (1)_W401

DSP-AX763 RX-V663/HTR-6160 RX-V663 DSP-AX763 RX-V663/HTR-6160 RX-V663 HTR-6160

CB61

CB62

CB63
(U, C models)
0
0

2 0 0
to DIGITAL 3/5

1.7 1.7 ANALOG IN

5.1 5.1
1.4 0
9.8 5.2 0 0
11.9
3.4 2.7 2.7 0
5.2 IC67
0
IC63 1.7 0
0
9.8 5.2 3.4 5.1
0
5.2 3.4 2.7 0

IC666
0 2.7 0

0 0 2.7
0
0 2.7 0
2.7 IC67
0

4 -11.4

2ch ADC

4.9 2.7
FL
0

IC64
11.9
3.3 2.8 0
IC68
1.6 2.8 0

1.7 0

1.3
5.3
1.7
to DIGITAL 3/5

1.7

0
2ch DAC 0
IC68
-11.4
0

4.9 2.7

3.3 2.7
IC65

1.6 2.8

1.7 0
C
0 11.9
1.3 5.3 0
IC69
0
C 1.7 2.8
2.8
SL/SR 1.7
5.3 2.7
SBL/SBR 0 2.8
1.3 0
SW
1.3 5.3 0
IC69
0 IC BLOCK DIAGRAMS DIGITAL 3/5
1.3 2.7 -11.4
0
6 DIGITAL IN 3.4 3.4 0 2.7

FL/FR
IC62

1.3 0
0 1.7
PL/PR 1.3
1.3
1.7
1.7
8ch DAC IC45, 46: TC74VHC153FT IC49: M12L64164A-5TG
IC51: EN29LV160AB-70TCP
0 0 IC44: D70YE101BRFP266 16 M-bit flash memory boot sector flash memory, CMOS 3.0 V-only
0 1.7
Floating-point digital signal processors Dual 4-channel multiplexer 1M x 16-bit x 4 banks synchronous DRAM
1.3 1.7 0 0
11.9
SL RY/BY# DQ0-DQ15 (A-1)
0 1.7 0 CLK Vcc Block Protect Switches
A 14 S0 Clock
0 Program/Data JTAG EMU Vss
IC70 256 RAM Generator Bank D
0 D1 S0 CKE Bank C
256K Bytes McASP0 Erase Voltage Generator
Data 64 32 Bank B
SELECTOR
16 Serializes S1 Input/Output buffers
R/W Program/Data
Address Row State
256 ROM Page1 S1

Row Decoder
C67x+ Microprocessor 32 Address
256K Bytes Control
D2 Memory B 2 S2 Buffer WE#
Data 64 Controller Program/Data 32 Mode & Bank A

McASP DMA Bus

R/W McASP1 S2 Register Program Voltage
256 ROM Page2 Refresh
256K Bytes 6 Serializes Generator
32 S3 Counter Command STB
Program Register Chip Enable Data Latch
I/O INT Fetch Program/Data S3 Output Enable
0 0 ROM Page3 32 McASP2 CE#
256 Sense Amplifier Logic
IC70 256K Bytes 2 Serializes L(U)DQM OE#

256
1C0 6

Command Decoder
-11.4 32 DIT Only 7 1Y CS Column

Peripheral Configuration Bus

0 S0 Column Decoder

Control Logic
Address
7 Program CSP 32 32
32 SPI1 RAS Buffer Y-Decoder Y-Gating

Input & Output

1C1 5

Latch Circuit
Cache 256 &

Address Latch
32K Bytes PMP DMP S1 Refresh STB
(U, C models)

Buffer
32 SPI0 CAS
Counter
Data Control Circuit DQ Timer
32 32 1C2 4 Vcc Detector
WE X-Decoder Cell Matrix
32 I2C0
S2
High-performance
Crossbar Switch 32
32 I2C1 1C3 3 A0-A19

32 32 32 32
S3
32 RTI
1G 1
11.9 VDD 1 54 VSS
32 PLL 2 53

0 0.3
SBL I/O Interrupts MAX0
Out
CONTROL MAX1 Events
In
2C0 10 9 2Y
DQ0
VDDQ 3 52
DQ15
VSSQ A15 1 48 A16
IC72 0 11.9 4 51 A14 2 47
EMIF S0 DQ1 DQ14 BYTE#
0.3 A13 3 46 VSS
0 2.7 0 DQ2 5 50 DQ13
0.3 IC71 dMAX A12 4 45
IC61

2C1 11 6 49 DQ15/A-1
0 Peripheral Interrupt and DMA Events VSSQ VDDQ A11 5 44 DQ7
0 2.7 DQ3 7 48 DQ12
S1 A10 6 43 DQ14
to DIGITAL 3/5

2.8 DQ4 8 47 DQ11 A9 7 42 DQ6

3.3 2C2 12 VDDQ 9 46 VSSQ A8 8 41 DQ13
10 45
A19 9 40 DQ5
1.7 0 S2 DQ5 DQ10
NC 10 39 DQ12
DQ6 11 44 DQ9 WE# 11 38 DQ4
0 5.3 2C3 13 VSSQ 12 43 VDDQ RESET# 12 37 VCC
DQ7 13 42 DQ8 NC 13 36 DQ11
1.7 S3 NC 14 35 DQ3
VDD 14 41 VSS
2G 15 RY/BY# 15 34 DQ10
LDQM 15 40 NC
1.7 0 0 A18 16 33 DQ2
0.3 WE 16 39 UDQM A17 17
IC71 32 DQ9
0.3 -11.4 CAS 17 38 CLK A7 18 31 DQ1
IC72
8 2ch DAC 0.3
-11.4
0 RAS
CS
A13
18
19
20
37
36
35
CKE
NC
A11
A6
A5
A4
A3
19
20
21
22
30
29
28
27
DQ8
DQ0
OE#
VSS
A12 21 34 A9 A2 23 26 CE#
A10/AP 22 33 A8 A1 24 25 A0
A0 23 32 A7
A1 24 31 A6
A2 25 30 A5
A3 26 29 A4
VDD 27 28 VSS

IC61: PCM1781DBQR IC65 : PCM1680DBQR

IC64: PCM1780DBQR IC66: PCM1803DBR IC67, 71, 72: NJM4565M IC68-70: NE5532DR
Audio digital-to-analog converter IC62: TC74VHC157FT IC63: NJM78M05DL1A Audio digital-to-analog converter
Audio digital-to-analog converter Stereo A/D converter Dual operational amplifier Dual low-noise operational amplifiers
BCK Quad 2-channel multiplexer Voltage regulator
Audio Output Amp and VOUT1
LRCK BCK DAC
Serial VOUTL Low-Pass Filter
DATA Port
Output Amp
SELECT 1 16 Vcc IN Audio Delta-Sigma BCK BCK V+
DAC and LRCK VINL 8 VCC+
Low-Pass Filter Serial Output Amp VOUTL Modulator LRCK LRCK
1A 2 ASG 15 ST DATA Port Output Amp and VOUT2
DAC and 36 pF
1B 3 14 4A DOUT DAC
4 /8 B A Low Pass Filter Serial Serial Low-Pass Filter
Oversampling 1Y 4 13 4B
Y B Input
9 (FMT)
Digital
Filter
With
Enhanced
Multilevel
Delta-Sigma
VCOM 2A 5 A Y 12 4Y
4 /8
Oversampling
Digital
Enhanced
VREF1
Reference
x 1/64, x 1/128
Decimation
Filter
Interface DATA1 (1, 2)
DATA2 (3, 4)
I/F
DAC
Output Amp and VOUT3
2, 6
Modulator 2B 6 B A 11 3A Multilevel Low-Pass Filter
Function (FMT) Filter VCOM DATA3 (5, 6)
MS (DEMP0)
Serial Control
2Y 7 YYB 10 3B OUT With
Delta Sigma VREF2 With Mode/ –INPUT OUTPUT IN+
Control GND 8 9 3Y MS (DEMP0) Function
Modulator High-Pass Filter Format FMT0 DATA4 (7, 8) 8 Output Amp and VCOM
+INPUT 1, 7 37 pF
MC (DEMP1) Serial DAC
Port Output Amp Control Control FMT1 Oversampling Enhanced Low-Pass Filter
DAC and Control Digital Filter Multilevel
VOUT4 3, 5
MD (MUTE) MC (DEMP1)
Low-Pass Filter VOUTR Port Output Amp With DeltaœSigma
DAC and Delta-Sigma MODE0 14 pF
VINR Function Modulator Output Amp and
MD (MUTE) Low Pass Filter VOUTR Modulator MODE1 DAC 15 Ω
Controller Low-Pass Filter VOUT5
(TEST) OUT
System Clock MS/ADR
BYPAS Output Amp and 7 pF
(TEST)
System Clock MC/SCL DAC IN
System TEST Low-Pass Filter
SCK
Clock Zero Detect MD/SDA
VOUT6 V– 15 Ω
Power Supply Function
Manager SCK System OSR Control
4
GND Clock Zero Detect Power Supply Clock and Timing Control PDWN I/F DAC
Output Amp and
Manager Power Supply Low-Pass Filter VOUT7
SCKI
FMT 1 16 ZEROA
MSEL Output Amp and
VCC

AGND
ZEROL/NA(1)

ZEROR/ZEROA(1)
(ZEROA)

DEMP0 2 15 VOUTL DAC

Low-Pass Filter VOUT8
DEMP1 VOUTR
VCC

3 14 VCC AGND DGND VDD

AGND
ZEROR/ZEROA(1)
(ZEROA)
ZEROL/NA(1)

VINL 1 20 MODE1
MUTE 4 13 VCOM 2 19 System Clock
VINR MODE0
(1) Open-drain output for the PCM1782 SCK 5 12 AGND VREF1 3 18 FMT1
NOTE: Signal names in parentheses ( ) are for the PCM1781. System Clock
DATA 6 11 VCC VREF2 4 17 FMT0 SCK Zero Detect Power Supply 460 Ω
Manager
ZEROL/NA 1 16 ZEROR/ZEROA VCC 5 16 OSR
BCK 7 10 NC
(1) Open-drain output for thePCM1782 MS 2 15 VOUTL AGND 6 15 SCKI VCC–
LRCK 8 9 TEST
NOTE: Signal names in parentheses ( ) are for the PCM1781. PDWN 7 14 VDD
10 MC
MD
3
4
14
13
VOUTR
VCOM
BYPAS 8 13 DGND

VCC1

VCC2
VDD
ZERO1

ZERO2

DGND

AGND1

AGND2
TEST 9 12 DOUT
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter. SCK 5 12 AGND LRCK 10 11 BCK

★ Components having special characteristics are marked s and must be replaced

DATA 6 11 VCC VCC+
1OUT 1 8
BCK 7 10 NC
1IN– 2 7 2OUT
with parts having specifications equal to those originally installed. LRCK 8 9 NC
1IN+ 3 6 2IN–
★ Schematic diagram is subject to change without notice. VCC– 4 5 2IN+

108
 A B C D E F G H I J K L M N

RX-V663/HTR-6160/DSP-AX763

DIGITAL 5/5
1
IC85: LC74782JM-8A16-TLMC
Page 114 K6 Page 115 I9 Page 113 K8
The on-screen display controller LSI
to VIDEO (1)_CB305 to VIDEO (2)_CB356 to MAIN (2)_W109
9 Serial 8-bits
latch
11 parallel +
converter command
decoder Horizontal Vertical Horizontal Vertical 31 inking Display RAM write
10

CB82
CB81
character character display display 3nd inversion control address

CB80
size size position position control register counter
register register register register register

Decoder
23 Horizontal Vertical 31 inking
size size Horizontal Vertical 3nd inversion Display RAM
counter counter dot counter dot counter control
register

24

31 inking 31 inking
3nd inversion 3nd inversion
1 control control
register register

2 REGULATOR
12
8 Character
control
Line
control
Decoder
VSS1 1 24 VDD1
counter counter XtalIN 2 23
4.7 RST
Horizontal XtalOUT 3 22 CTRL3
3.3 character
size Font RAM CTAL1 4 21 CTRL2
3.3 4.7 Horizontal register
6 character BLANK 5 20 SEPIN
0 size

IC80
7 register OSCIN 6 19 SEPOUT
Character output Shift
Timing generator Synchronization control register OSCOUT 7 18 SEPC
signal generator Background control
17 Horizontal Horizontal Video output control
CHARA 8 17 SYNIN
character character 9 16

to DIGITAL 2/5
18 size size CS VDD1
register register SCLK 10 15 CVIN
19
4.8 SIN 11 14 NC
20
2.5 2.5 2.4 2.4 2.4 2.4 VDD2 12 13 CVOUT
22
21 4 2 3 5 15 13
0

IC80: R1172S331B-E2-F
IC86
CMOS-based positive-voltage regulator IC
0 0
0 4.8 4.8 0
VDD 6 1 VOUT
3 0
Pin No. Symbol Description
1 VOUT Output Pin of Voltage Regulator
0 2, 5 GND Ground Pin
0 4.8
3 CE Chip Enable Pin

0
0
0
3.3
0
3.3
0
0
3.3
0
0
0
4 NC No Connection

VIDEO DECODER Vref

1.9
6 VDD Input Pin
1.3 0.7 Current Limit
CE 3 2,5 GND
2.5 2.5 2.5 2.5
4.8
3.3
1.3
VIDEO 1.5

1.3
2.5 3.2
0
2.4 0

3.3
ENCODER 3.3
IC99: R1172S181B-E2-F
3.3 IC84 3.3
0 0
Voltage regulator
3.3 3.3
IC87
3.3

IC99
3.3 3.3
0 0
3.3
0 VDD 6 1 VOUT
0 4.8 4.8 0 0 3.3 5.0
0 0 Pin No. Symbol Description

to DIGITAL 2/5
3.3 0 3.3 1 VOUT Output Pin of Voltage Regulator

0.3
2, 5 GND Ground Pin
0 0 3 CE Chip Enable Pin
4 0
4.8
3.3 5.0
4 NC No Connection

0
0.8
0.8

0
0
0
0
0
Vref

3.3

3.3
0
0 0 6 VDD Input Pin
Current Limit
CE 3 2,5 GND

to DIGITAL 1/5
3.4

3.4
0
0

0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1.8
3.3

1.7
1.8
3.4

1.8
0

1.8
0
0
0
0

0
5
0
0
1.0
0.8 C-1
0
0.3

0.3
0
VIDEO DECODER 0

3.4
0 1.8
0.3 0
0
0

3.4
0
0
0
3.4 IC82
6 0 POINT B-3 XL80 (Pin 3 of IC85)
0
0
0
0.4 1.8

0 0
0 3.3
1.6 0
0 2.6
2.6 1.7
3.3
2.6 3.3
0.4 3.2
2.6 3.3
1.6 1.6 1.7
0 2.6 3.3
0
1.6 2.6 3.3
0 3.3
2.6 3.3
0 0.9 1.6 IC89
1.7
2.6 3.3
3.3 0.7
0 3.3

IC91
1.6
3.2 0.8
3.3 0
3.3 0.8
3.3 0.8

7 0
0
0
0
2.6 0

0 0
2.6 3.3 POINT C-1 XL81 (Pin 81 of IC82)
0 3.3 2.6
0
5.0 3.3 3.3
0 1.7
0 0 0 3.1
5.0 0 3.3
0 0
0 0 0 3.3

OSD 0 0
0 1.4

IC92
0 1.3
0.4
5.0

5.0

2.0

3.3 0
5.0
4.9

5.0
0

0
0
0

0.7
2.1
0
0
0

0
1.8
0
0
0
0
0

0
0
0
0
0
0
0
0
0
0
0
0
0

1.8
0

1.3
1.2
1.2
1.0
0.9
1.4
3.3
0
0

0
0
0
0
1.7
0

0
3.3
3.3

3.4
-4.9 0 0

IC85 2.6 3.3

0
0 3.3
0

0 3.2
2.6
2.6
2.4

3.2
0

B-3
2.5
2.5

5.0
5.0
0.9
5.0

2.6 3.3

8 0.9 0.3
2.6 3.3
2.6 3.3
5.0 0.5
0 3.3

IC93
5.0 4.9 0
3.3

BUS BUFFER

DSP-AX763 RX-V663/HTR-6160 RX-V663 DSP-AX763 RX-V663/HTR-6160 RX-V663

IC82: ADV7800BSTZ-80
9 10-bit, SDTV/HDTV 3D comb filter, video decoder and graphics digitizer
DDR/SDR-SDRAM INTERFACE

STANDARD DEFINITION PROCESSOR (SDP)

12 ANTIALIAS 10 10
CLAMP ADC DDR/SDR-SDRAM INTERFACE
FILTER
AIN1
TO 10 10
AIN12 ANTIALIAS 525p/625p MACROVISION STANDARD
INPUT MUX

CLAMP ADC 54
FILTER SUPPORT DETECTION AUTODECTION PIXEL DATA
CVBS
MUX

IC84: ADV7172KSTZ S-VIDEO

10 10
P0 TO P53
YPrPb ANTIALIAS
Digital PAL/NTSC video encoder SCART-
(CBVS+RGB)
CLAMP
FILTER
ADC
2D COMB
AV CODE
INSERTION
VERTICAL
GRAPHICS RGB PEAKING
CLOCK PAL NTSC CSO_HSO VSO CLAMP SCLOCK SDATA ALSB IC86, 87: TC74VHCU04FT IC89: TC7WZ32FK (TE85L, F) IC91-93: SN74LVC245APWR CLAMP ANTIALIAS
ADC
10 10
OUTPUT FIFO AND FORMATTER

FILTER COLORSPACE
Hex inverters Dual 2-input OR gate Octal bus transceivers with 3-state outputs FAST BLANK HORIZONTAL CONVERSION CS/HS
HSYNC M 3D COMB OVETLAY PEAKING
10 U 10 10-BIT
FIELD/ VIDEO TIMING I2C MPU PORT YUV TO DAC A DIR 1 20 Vcc CONTROL
VSYNC RBG L DAC FB VS
GENERATOR T CTI
1A 1 14 VCC
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
BLANK MATRIX 1A 1 8 Vcc
10 I 10
+ 10-BIT A1 2 19 OE
YUV P DAC DAC B
RESET
TTX
LEVEL
CONTROL 10
L
E
X
10 10-BIT
DAC C
1Y 2 13 6A 1B 2 7 1Y
A2 3 18 B1
TBC
LTI ITOP FIELD/DE
★ Components having special characteristics are marked s and must be replaced
TELETEXT BLOCK DAC CVBS OUT DAC
TTXREQ INSERTION BLOCK E
R
2A 3 12 6Y 2Y 3 6 2B
with parts having specifications equal to those originally installed.
10 VAA BRIGHTNESS AND
CONTRAST CONTROL
+
10
LUMA
PROGRAMMABLE
FILTER
DAC
CONTROL
VREF
RSET2
2Y 4 11 5A GND 4 5 2A A3 4 17 B2 P30 TO P53
HS_IN2
24

DIGITAL INPUT PORT

CORE
VBI DATA PROCESSOR (VDP) SFL/SYNC_OUT
★ Schematic diagram is subject to change without notice.
M BLOCK VS_IN2 CLK
8 Y 8 ADD SYNC + U COMP2 A4 5 16 B3 DVI OR HDMI
+ SHARPNESS 3A 5 10 5Y CLK_IN COMPONENT PROCESSOR (CP)
L 10 DE_IN
INTERPOLATOR FILTER T 10-BIT LLC
P0 4:2:2 TO YCrCb DAC E
10 I DAC 3Y 6 9 A5 6 15 B4
COLOR 4:4:4 8 TO U 4A MACROVISION ACTIVE PEAK
YUV SATURATION CONTROL 10 P
DATA INTER- MODULATOR L 10 10-BIT HS_IN SYNC PROCESSING AND DETECTION AND AGC
POLATOR MATRIX 8 + PROGRAMMABLE 10 DAC F
ADD BURST CHROMA + E DAC GND 7 8 4Y A6 7 14 B5 VS_IN CLOCK GENERATION
P7 10 HUE X
8 V 8 + FILTER 10 10 SOG
INTERPOLATOR CONTROL E 10-BIT INT
DAC D SSPD STDI DIGITAL
R DAC A7 8 13 B6 SOY COLORSPACE GAIN OFFSET AV CODE
FINE
10 10 CONVERSION CONTROL CONTROL INSERTION
CLAMP
REAL-TIME SIN/COS DAC
ADV7172/ADV7173 CONTROL CIRCUIT CONTROL RSET1 A8 9 12 B7 SCLK
DDS BLOCK
BLOCK SCLK2
COMP1 SERIAL INTERFACE
SDA
GND 10 11 B8 CONTROL AND VBI DATA
SDA2
SCRESET/RTC GND ALSB

109
 A B C D E F G H I J K L M N
RX-V663/HTR-6160/DSP-AX763

1
FUNCTION 1/2

IC202: R2A15218FP
8-channel electronic volume with 11 input selector and tone control
AUDIO MULTI CH INPUT PRE OUT

BASSR2

BASSR1
(R, T, K, A, B, G, E, F, L, J models)

SBRCIN
SBLCIN

SBRIN2
CLOCK

SBLIN2
SWIN2
DGND

SRIN2
FRIN2
SUBR

SLIN2
FLIN2

TRER
SUBL
DATA

CIN2

N.C.

N.C.
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31
A VCC
MUTE 51 30 AVCC
MCU
AVEE 52 I/F 29 N.C.
A VEE
N.C. 53 28 TREL
0/-6/-12/-18dB
ADCL 54 27 BASSL2
ATT
ADCR 55 26 BASSL1

25 N.C.
2 AGND 56
N.C. 57
MAIN
SUB
0~-95dB,
-∞
(0.5dBstep)
Bass/Treble
-14~+14dB
(2dBstep)
Bypass
+42~0dB
(0.5dBstep) 24 FRC

MAIN
MAIN
Tone+MIX Tone
INR1 58 Tone 23 FROUT

INL1 59 +42~0dB 22 AGND

(0.5dBstep)

INR2 60 Tone 21 FLOUT

Tone+MIX Tone

SUB
INL2 61 Bass/Treble Bypass 20 FLC
0 0 0~-95dB,
0 0 -∞ -14~+14dB
(0.5dBstep) (2dBstep)
INR3 62 19 AGND

SUB

CMIX
-11.4 -11.4 INL3 63 18 CC
0 0 0 0 +42~-95dB
0 0 -∞(0.5dBstep)
0 0 INR4 64 17 COUT

SWMIX
0.9 0.9
-11.4 INL4 65 16 AGND
IC201

0 0 0 0 -11.4 +42~-95dB
INR5 66 -∞(0.5dBstep) 15 SWOUT
IC201

0.9 +42~-95dB
ANALOG IN 0.9
INL5 67
-∞(0.5dBstep)
14 SWC

INR6 68 13 N.C.
0
INL6 69 +42~-95dB 12 SRC
-∞(0.5dBstep)
0
INR7 70 11 SROUT

0
0
0 0

-6.9
3

2.5
2.5
0 -6.9 INL7 71 10 AGND

0
0
0

0
0

0
0

0
0

0
0

0
0
+42~-95dB

IC203
0 0 -∞(0.5dBstep)
0 7.1
INR8 72 9 SLOUT

0
0 0
0 SUB INL8 73 8 SLC
0 0
0

0 0
WOOFER N.C. 74 +42~-95dB
-∞(0.5dBstep)
7 A GND
0 0
0 0 INRA/RECR1 75 6 SBRC
0 0 REC
0 0
0 0 INLA/RECL1 76 5 SBR OUT
0 0

(U, C, R, T, K, A, G, E, F, L, J models)
0 0
0
N.C. 77 4 AGND
0 0
-6.1

7.1 IC202
0

0
0
0
0
0
RDS IC INR9 78

INL9 79
3 SBL OUT

2 SBLC
0 0
0 0
N.C. 80 1 N.C.
0 0
to OPERATION (4)_W441

0 0
81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

to TUNER
0
INPUT & ZONE2 0 IC241

INRB/RECR2

INLB/RECL2

INR10/RECR4

INL10/RECL4

INR11/RECR5

INL11/RECL5
N.C.

N.C.

N.C.
RECR3

RECL3

N.C.

FLIN1

FRIN1

CIN1

SWIN1

SLIN1

SRIN1

SBLIN1

SBRIN1
0 0
0 0

8ch SELECTOR/
N4

7.0 9.7
0 0
CB201
0 0 7.7

4 0
MASTER VOLUME 0
Page 112

0 0
0 0 7.7

0
0
0
0
CB242
0
0

0
0

0
0

0
0

0
0

0
0

0
0

7.1
0

0
CB243
0

-7.7

DSP-AX663 RX-V663/HTR-6160 RX-V663 DSP-AX763 RX-V663/HTR-6160 RX-V663 HTR-6160

to VIDEO (1)_CB302

-7.2

-7.0 -9.3
H2

to FUNCTION (5)_W2505
Page 114

E4
10.6

(B model)
W2503
0
IC225 0

Page 111
0
0 0 -6.1 58.3 58.3 58.3 58.3

5
-6.1
SURROUND
0 0
FRONT L 57.7
CENTER 57.7
SURROUND L 57.7
BACK L 57.7

0 0 -6.1 1.1 1.1 1.0 1.1

-6.1

0 0
0 57.7 57.7 57.7 57.7
0 58.8 58.8 58.7
CB205 IC225 58.8
0
0 0 0 0
-10.1
0 0 -0.5 -0.5 0 -0.5 -0.5 0 -0.5 -0.5
-0.5
0
-0.5

10.6

0
IC226
0
0
0 0 -11.4
-11.4
to DIGITAL_CB61

0 0
B2

FL 0 0
-11.4
Page 108

6 0
0
0 0 -11.4

0 IC226 58.3
C -10.1
58.3 58.3

57.7 57.7 57.7

1.1 1.0 1.1

10.6

0
SW IC227 0 57.7
58.8 57.7
58.7
57.7
58.7
0
0 0 0
SL 0
-0.5 0
-0.5 -0.5
0
-0.5 -0.5
-0.5 0
0
0
SBL 0
IC227
-10.1

7
0
-6.1

0 0
-6.1

0 0 0
-6.1 -11.4

0 0 0 0

-6.1
0 0 -11.4

CB246

11.5 10.8
Page 111 B3
0 to FUNCTION (9)_CB247
0.8 -11.5 -10.4
0

0 0 -11.4
-11.4

0 0
8 0

0.8
0
FUNCTION (1)
CB206

CB221

CB231

CB232
Page 106 I2 Page 112 J9 Page 113 B10 Page 113 B4
to DIGITAL_CB34 to OPERATION (1)_W402 to MAIN (1)_W106 to MAIN (1)_W105

IC203: BD3841FS
IC241: LC72725KM-UY-TLM-E
Function switch
9 RDS signal demodulation IC
RECC1

RECC2
RECA1

RECA2

RECB1

RECB2

IC201: NJM2068MD-TE2 IC225-227: NJM4565M

DGND

OUT1

OUT2
BIAS

VCC
VEE

INI1

INI2
DA
CL

Dual operational amplifier Dual operational amplifier 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 +3V VREF FLOUT CIN +3V
Vdda Vddd
V+ PLL
CLOCK
8 LOGIC REFERENCE (57kHz)
RECOVERY
(1187.5Hz)
VOLTAGE
Vssa Vssd
VREF
OUT1 1 8 +VCC PHONO O X O X O O O O O O X
57kHz
+

+
–

MPXIN ANTIALIASING BPF SMOOTHING DATA RDDA

–IN1 2 7 OUT2 2, 6 (SCF) DECODER
FILTER FILTER
+ – + – –INPUT OUTPUT RDCL
+INPUT 1, 7
+IN1 3 6 -IN2
3, 5 RAM
MODE
F-SW1

F-SW2

(128bits)
–VCC 4 5 +IN2
RST
CLK(4.332MHz)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
RDS-ID RDS-ID/
INA1

INA2

INB1

INB2

INC1

INC2

IND1

IND2

INE1

INE2

INF1

INF2

ING1

ING2

INH1

INH2

TEST TEST
OSC DETECT READY
V–
4 * F-SW1: INPUT FUNCTION 1
F-SW2: INPUT FUNCTION 2
XIN XOUT
10 RDS-ID/READY 1 16 RDCL

★ All voltages are measured with a 10MΩ/V DC electronic voltmeter. RDDA 2 15 RST

★ Components having special characteristics are marked s and must be replaced VREF 3

4
14 XOUT

MPXIN 13 XIN
with parts having specifications equal to those originally installed. Vdda 5 12 Vddd
★ Schematic diagram is subject to change without notice. Vssa 6 11 Vssd

FLOUT 7 10 MODE

CIN 8 9 TEST

110
 A B C D E F G H I J K L M N

RX-V663/HTR-6160/DSP-AX763

FUNCTION 2/2
1

FUNCTION (9)

10.8
0 0
IC220
0
to FUNCTION (1)_CB246

CB247
G8
Page 110

3
0
0
0 IC220

-10.4

FUNCTION (5)
B model

W2505
Page 110 J4
to FUNCTION (1)_CB243

FUNCTION (6)

To POWER CABLE
5 CB297 (U, C, R, T, K, A, B, G, E, F, L models)
Page 114 K5 Page 115 I7 To POWER TRANSFORMER
to VIDEO (1)_CB304 to VIDEO (2)_CB355

CB296

(J model)
FUNCTION (2)
CB253

CB258
J model

CB254 CB255 AC IN

6 CB256 CB257

W2502A

W2502B
(0.3)

(0.3)

(7.5) 0.2
(0) 0

(7.7) (0)
4.9
0 5.2
5.2
(1.0) (7.7)
(7.7)
7
IC252

0 0 0 0 IC251 (0.9) (3.6)

FUNCTION (4)
0
5.2 9.6 (0) (0) R, L models
0 4.8 9.6
(7.5) (0)
W2501 0
to DIGITAL_CB33

0 0 (0) (3.9) (7.7) (0) (0)

0 4.8 9.6
F2

0 (0) (0)
(3.9)
Page 106

(0) IC252: TC4013BP

(7.5)

Primary side ground IC253 0 4.8 4.8 IC220: BA15218F Dual D-type flip flop
3.9 12.5 Dual high slew rate, low noise operational amplifier
12.5
0 VOLTAGE RESET1 4
(0) 0
SELECTOR OUT1 1 8 VCC
0.8 SET1 6 1 Q1
8
To POWER TRANSFORMER

0.1 DATA1 5
2 Q1
– IN1 2 7 OUT2 CL
CB263 CB264 1ch CL
– + CL
0 CL
VOLTAGE SELECTOR + IN1 3
2ch
6 – IN2
CLOCK1 3 CL
4.8 + –
230-240V 1-2/5-6 CL

220V 2-3/6-7 RESET2 10 Q1 1 14 VDD

0.1 12.5 VEE 4 5 + IN2
0 110V 3-4/7-8 SET2 8 13 Q2 Q1 2 13 Q2
120V 4-5/8-1 DATA2 9
12 Q2 CK1 3 12 Q2
CB261

CB262

0.1 12.5 CL CL
to MAIN (2)_W108

RESET1 4 11 CK2
CL CL
K8

CB251 CLOCK2 11 CL DATA1 5 10 RESET2

4.2 CL
SET1 6 9 DATA2
To POWER TRANSFORMER VSS 7
Page 113

VDD 14 Vss 7 8 SET2

9.1 0 To POWER TRANSFORMER
9
INPUTS OUTPUTS
RESET SET DATA CK Qn + 1 Qn + 1
4.2
L H * * H L
H L * * L H
H H * * H H
L L L L H * : Don't care
FUNCTION (3) L
L
L
L
H
*
H
Qn˙
L
Qn˙
: Level change
˙ : No change
CB252

AC8.3

To POWER TRANSFORMER

10
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
★ Components having special characteristics are marked s and must be replaced
with parts having specifications equal to those originally installed.
★ Schematic diagram is subject to change without notice.

111
 A B C D E F G H I J K L M N
RX-V663/HTR-6160/DSP-AX763

1
OPERATION

OPERATION (4)

OPERATION (5) 5.0

IC441

VOLUME 4.3 5.0

4.3 0

2 0

5.0 W442
OPTICAL
Page 107 E2
to DIGITAL_CB46

JK441

-20.9

-20.9

-20.7

-20.7
-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.8

-25.6

-25.7

-25.8

-25.8

-18.6

-14.8

-16.6

-16.4

-23.9

-13.0

-22.7

-22.7

-25.8

-15.0

-16.7

-22.0

-20.2

-20.3

-18.3

-15.0

-21.5

-25.8

-20.2

-18.5

-13.0

-13.1

-16.4

-20.2

-22.1

-25.9

-25.8

-23.9

-23.9

-20.2

-23.9

-23.9

-18.5

-18.5

-23.6
DSP-AX763 RX-V663 DSP-AX763 HTR-6160 S VIDEO
0

3 0
0

0
VIDEO
5.0

-20.2

-20.3

-15.0

-25.8

-20.2

-18.5

-13.0

-13.1

-16.4

-20.2

-22.1

-25.9
5.0

5.0
-23.9 -18.5

-23.6 -18.3 VIDEO AUX

-22.0 -23.3

-25.8
-18.5

-22.1
-16.7 -23.7
Page 110 A4
-15.0 -20.2 to FUNCTION (1)_CB201
-25.8 -23.9 INPUT
W441
-22.7 FL DRIVER -23.9 SELECTOR
AUDIO
-22.7 -18.5
4 -13.0 -18.5 0.8 0.8 0

-23.9
IC401 -23.9

-16.7 5.0 0
0
5.0
5.0 -16.6 2.2
2.2 5.0
0
-14.8

5.3

5.2
-22.1 -16.7
-25.8 -18.6 0
-21.5 -16.4
-25.8 0.3
-25.7
-25.8 5.0
5.0 5.0 -25.8
4.9
-25.9 -25.8 -25.8 4.9

TONE
-25.8 -25.6 CONTROL OPERATION (3) 0

-25.9
-21.3
5

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-25.9

-27.9
0
0

To POWER TRANSFORMER
-24.6

0
0
-27.9
OPERATION (2)
MAIN ZONE ON/OFF 5.0 JK431
(RX-V663/
W403 CB421
(B model) HTR-6160: U, F models)

OPERATION (1) CB431 PHONES

CB422

6 AC4.9

STANDBY/ON
(HTR-6160: C model/
DSP-AX763)

5.0 5.3 5.3

5.0 5.3 0 0

0
0 0 0
5.0
5.0
5.0 0 0
0 0

0 0 5.1 JK401
0
0 0 0 0 0 0 OPTIMIZER
MIC
5.0
0 0 0 0

7 0
0
0 0 0
5.0 0 11.9
5.3 5.3 5.3
0 PURE DIRECT 0

SCENE1 SCENE2 SCENE3

0
SCENE4 5.0
LED 0
1.3
IC402 0
11.4
0
LED 5.0 LED 5.0 LED LED IC402 1.2
0
2.9 0
3.7 3.6 3.6 3.6

0
0
2.9
-11.4

0
0

8
4.0

0
W404
3.7

3.7

W401 W402
CB401

9 IC401: M66003-0131FP-R
Page 106 B2 Page 108 F2 Page 110 G8 18 digit 5 x 7 segment VFD controller/driver
to DIGITAL_CB30 to DIGITAL_CB63 to FUNCTION (1)_CB221
Display code
RAM CGROM
(35-bit x 166) 44 SEG00
(8-bit x 60)
Code Segment 19 SEG25
write output 17 SEG26
circuit
dot data
CGROM 9 SEG34
CS 2 Serial data (35-bit x 16)
write
receive
IC402: NJM4565M SCK 3
circuit Code/
IC441: TC7SET32FU SDATA 4 command
Dual operational amplifier control 45 SEG35
2-input OR gate circuit
52 DIG11/
SEG42
51 DIG12/
SEG41
Segment/
V+ code
Digit 50 DIG13/
1 select
IN B 5 VCC 8
select/
SEG40
49 DIG14/
XIN 7 Clock output SEG39
timing Display
IN A 2 generator clock controller scan pulse circuit 48 DIG15/
XOUT 6 SEG38
DIG16/
10 GND 3 4 OUT Y –INPUT
2, 6
OUTPUT
47

46
SEG37
DIG17/
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter. +INPUT 1, 7 SEG36

★ Components having special characteristics are marked s and must be replaced 3, 5

Digit
63 DIG00

with parts having specifications equal to those originally installed. RESET 1 output
circuit
★ Schematic diagram is subject to change without notice.
Vcc1 8 53 DIG10
Vcc2 18
Vss 5
V– Vp 64
4

112
 A B C D E F G H I J K L M N

RX-V663/HTR-6160/DSP-AX763

MAIN
1

57.0
57.0
56.9
0.2
57.0 DSP-AX763 RX-V663/HTR-6160 RX-V663 RX-V663/HTR-6160 DSP-AX763 HTR-6160
1.1
1.4 1.4 1.1
0.4

0 -0.6 56.7

-0.6 0.4
0.4
FRONT B/ZONE B/
ZONE2/PRESENCE
2
0.4

0 0
FRONT A
-0.6 -0.6 -56.9
-56.9
-53.9 0.3 SURROUND
-54.5
-54.5
0
BACK L 0.4 0.4 0.4

-55.1
0 0 0
5.3
0

SPEAKERS
0 0 0 0
57.0 CENTER
1.4 0.4 0.4 0.4 0.4
57.0
1.0 1.0
1.4

3
1.4 56.7
0.4
0.4
0
-0.6
0.4
SURROUND
-0.6 1.0

0.4
0
0 SURROUND BACK/
FRONT L
-0.6 -0.6
-56.9 -56.9 BI-AMP
-53.9 0.3

-54.5
-54.5 0

-55.5
Page 106 E2
W105
to DIGITAL_CB32
W104

4 Page 110 I8 1.4

57.0

57.0

to FUNCTION (1)_CB232 1.4

1.4
0.9
0.9

0.4 Page 106 D2

0
-0.6 56.7

-0.6 0.4
0.4
to DIGITAL_CB31

12.2 12.2 12.2 12.2 12.2 12.1 12.2

0.4
W103 IC101: LM61CIZ
12.1 0 0 0 12.1 0 12.2 IC100, 102, 106: NJM2388F05
Temperature sensor
0.4 0.4
12.1 12.1 12.1 -11.6 12.1 -11.6
Low dropout voltage regulator with ON/OFF control
-11.6 12.2
-0.6 -0.6
-56.9 -56.9
SURROUND L 12.1

-53.9 5.1 0.2

-54.5 -54.5
0.3 0 VIN VOUT
0
0
-55.1 0 5.1

0
0

5 5.1

0
0 Bandgap
0.2 Reference
57.0 0
0
1.1 ON/OFF
57.0
5.1
Cont control
1.1 0.9 12.1
0.9 0
1.1
0.4 0.3 Over Voltage Thermal Over Current
0
-0.6 56.7
Protection Protection Protection
-0.6 0
0.4
0.4
GND
12.1 12.1 12.1 -11.6 12.1 -11.6
-11.6

-11.6 -11.6 -11.6 -11.6 -11.6 -11.6

0.4 -11.6

-0.1 -0.1

-0.6 -0.6
-56.9 -56.9 CENTER
-53.9
6 -54.5 -54.5
0.3 -27.9
-35.6

-55.1 0
IC104: KIA7812API IC105: KIA7912PI IC110: NJM7805FA
-28.5

Voltage regulator Voltage regulator 3-terminal positive voltage regulator

1 INPUT 1 COMMON (GND)
R22
R22 R17 R23 R15 R18 R21 R23 INPUT

To POWER TRANSFORMER
0 R1 Q11 Q11-1 Q28 Q17 Q21
Q22 Q24
Q15
Q16 R16 Q23 R13 R12
57.0
AC51.3
Q12 Q19 R24
57.0 57.1 Q14 R14 Q29
1.4
1.4
0.9 CB100
R10 R15
R1
R20 OUTPUT
1.4 Q17 Q19 R16 Q18 Q20
0.9 R19 Q25
R12 3 OUTPUT Q30
0.4 R14 R17 Q31
0 Q18 Q6 R20 R25
0 -0.6 R19
56.7
Q1
-0.6 57.1 R18
0.4 -56.9 R11 Q12 Q13
R9
0.4 R7 C1 Q2 Q3 Q26-1 R11
Z1 R10
R2 Q10 R26
0 Q2
Q26
Q27-1
Q27 3 OUTPUT
Q7 D4 Q14
Q7 R21
Q13 R3 Q15
AC87.2
Q4
R0 C2 C1 Q16
GND
R9
7 0.4
R13
Q3 Q5 Q9 Q8 Q4
Q5
Q6
R3
Q8
Q9
R4 R5
Q11
R6

0.1 R4 R5 Q10
-0.1 R6 R8 R2 R8
R7
2 COMMON (GND) 2 INPUT
-0.6 -0.6 -56.9
-56.9
-53.9
0.3
-54.5 -54.5

-55.1 0 -35.7
-26.8
-56.9

-9.3
-18.2

To POWER TRANSFORMER
20.1

0 CB101
0
AC31.4

1.4
57.0
4.8 12.1 Page 111 B9
57.0 W108
1.4
1.4
0.9
0.9
0.4
-20.6
MAIN (2) 12.1 to FUNCTION (3)_CB251
56.7 AC16.5 6.1
0 -0.6
-0.6 0.4 6.1 6.1
0.4

8 0.9
AC10.5
6.1 W109

9.8 12.0
0.4
0
Page 109 J2
0.4 9.8 0 5.7
0 5.7
to DIGITAL_CB82
0.4 0.4
3.0 -10.4 0
-0.6 -56.9
-56.9
-53.9 -0.6 IC104 W107
0.3 12.2
-54.5 20.1
-54.5

W100A W100B 0
-55.0 0

Page 108 D2
0
-11.5 to DIGITAL_CB62
-20.2

IC105
57.0 IC110 W110
57.0 56.5 56.5
1.5
0.9 56.5
0.9 12.0 4.6
1.5 0

9 1.5 0.4

0.4
56.7

0.9 56.5 16.0 12.2

-0.6 0.4
-0.6 4.3
-0.6 4.8
4.2

0.4 11.6
10.9 11.6

0.8
0 IC102 IC105 IC107 W114
0
0.4
0

-0.6 0.1 0
13.0
0.4 Page 114 K3
-55.7

9.8

9.8
5.0
0

5.0

9.8
3.3
0

5.0
0
0.3 IC101
-0.6
-56.9 -56.9
5.1 to VIDEO (1)_CB303
-53.9
-54.5 -55.7 1.0 4.6 5.0
-54.5 0 0
-55.1 -56.9 0
-55.1
-13.0
0
W106 -12.5 W113
-48.7 0 0
Page 106 H2
0
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
Page 110 I8 to DIGITAL_CB38
★ Components having special characteristics are marked s and must be replaced
-0.6 -0.6
-6.1

to FUNCTION (1)_CB231 (J model)

with parts having specifications equal to those originally installed.
10 ★ Schematic diagram is subject to change without notice.
-10.4

-6.5

-10.4 -4.9

MAIN (1) REGULATOR

113
 A B C D E F G H I J K L M N
RX-V663/HTR-6160/DSP-AX763

1
VIDEO 1/2

4.6 4.6

4.6

2
No replacement part available.

CB301

CB302 4.6

Page 110 A5
0
to FUNCTION (1)_W2503
DOCK

11.5
0 0
IC331
0

3
IC305

CB303
0
0
0 IC331

4.9

9.0
12.0
-11.9
Page 113 K9
to MAIN (2)_W114

JK301

IC301: TC4051BF
Multiplexer/demultiplexer
5.0 VDD
16

IC304
0.2 0
-4.8 13 0
5.0 I/O c O/I
5.0 0
0 A 11 I/O c O/I 14 1
0.1 0 0.7
-4.8 9.0 5.0 I/O c O/I 15 2
0 0 0.7

LOGIC LEVEL
CONVERTER
0 0.7 I/O c O/I 12 3
0.1 0 B 10
IC302

0.1 0 I/O c O/I 1 4

CB304
5 4.9 0
4.9 C 9 I/O c O/I 5 5

Page 111 B5 I/O c O/I 2 6

9.0 5.0
INH 6 I/O c O/I 4 7
to FUNCTION (6)_CB296
3 COMMON

0.2 0 8 7
-4.8 VSS VEE
5.0 4.9

5.0 0
JK302 0.1 0 0.2 0.2
0.9
0.1 0 0.2

0.1 0
IC302, 303: TC74HC4051AFEL
8-channel analog multiplexer/demulitiplexer
IC303

0.1 0 -4.8

4.9 0 4.9
COM
OUTC IN 0

Logic Level Converter

A 1
4 1 16 Vcc
2
6 0 B 3
COM 3
6 2 15 2
14 1
0.9
IC333 4 7 4 13 0
0 5.0 0 0.2
5 5 5 12 3
C
6 INH 6 11 A
-4.8
OUTC IN 7 VEE 7 10 B
INH
0 GND 8 9 C

0.5 5.0 IC333 0

Page 109 E2
to DIGITAL_CB80
0
IC304: TC74HC4053AF
0.9
VIDEO

0
IC333 Analog multiplexer/demultiplexer
5.0 0 0.2
-4.8
INHIBIT VCC
6 16

A 11 INPUT STATES
LEVEL BINARY TO 1-OF-8 "ON" CHANNEL (S)
B 10 INHIBIT C B A
CONVERTER DECODER WITH INHIBIT
7 C 9 0 0 0 0 0X, 0Y, 0Z
8
0 0 0 1 1X, 0Y, 0Z
GND
0 0 1 0 0X, 1Y, 0Z
JK303 0.2 0 VEE 7
0 0 1 1 1X, 1Y, 0Z
9.0 -4.8 0X 12 SW
0.9 14 X-COM 0 1 0 0 0X, 0Y, 1Z
9.0 0 0.4 1X 13 SW
0.7 0 1 0 1 1X, 0Y, 1Z
0 0 0Y 2 SW 0 1 1 0 0X, 1Y, 1Z
15 Y-COM
0 0 1Y 1 SW 0 1 1 1 1X, 1Y, 1Z
0 0 0Z 5 SW 1 X X X NONE
CB305 4 Z-COM
IC301

0 0 3 SW
9.1 0

INPUT 0.9
0.4
SELECTOR 0.4

8 0
5.0 IC333
0

0
BYPASS SW IC332, 333: LA73050-TLM-E
IC305: NJM2388F09
Low dropout voltage regulator with ON/OFF control
6-channel 75-ohm video driver
VIN VOUT
0

0.5 5.0 IC333 0

0.9
0.4 Bandgap
0 0.4
Reference
0
5.0 IC333 0
ON/OFF
Cont control

RECOUT AMP Over Voltage Thermal Over Current

-4.7

4.9
-4.7
-4.7

4.9
-4.7

4.9

-4.7
4.9

-4.7

0
0

Protection Protection Protection

0
0

0
GND
0 5.0 IC332 0
0 IC332 IC333

IC332 0
-4.7

0 0
9
0

-4.7

IC332 0 IC331: NJM4565M

MONITOR OUT 0 5.0 0

0 0
IC332 0 Dual operational amplifier

0 0
V+
8
IC332 0 IC332 0
0 5.0
OUTPUT AMP 0 0

VIDEO (1) –INPUT

2, 6
OUTPUT
+INPUT 1, 7
3, 5

V–
10 4
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
★ Components having special characteristics are marked s and must be replaced
with parts having specifications equal to those originally installed.
★ Schematic diagram is subject to change without notice.

114
 A B C D E F G H I J K L M N

RX-V663/HTR-6160/DSP-AX763

VIDEO 2/2
1

(J model)

CB351
2

9.0

9.0
0

0
9.0
9.0
0 INPUT

IC384
9.0

0 SELECTOR
0

9.0

IC392
0
CB352 9.0
0
0 0

0.4

3 0
0.4 0
0

0.4
4.9
4.9
0
0
4.8

9.0

0.4
IC383
D5 VIDEO

CB353

4
SELECTOR
CB354

5 IC351: NJM2581M IC383: TC74HC4052AF

Video amplifier Analog multiplexer/demultiplexer

INH VCC
6dB 75
VIN1 1
AMP Driver 14 V+1 6 16
INHIBIT B A
0 0 0 0x, 0y
BIAS
NEE1 2 13 VOUT1 A 10 LEVEL BINARY TO 1-OF-4 0 0 1 1x, 1y
B 9 CONVERTER DECODER WITH INHIBIT 0 1 0 2x, 2y
VIN2 3 6dB 75
12 V+2 GND 8 0 1 1 3x, 3y
AMP Driver
VEE 7 1 X X NONE
BIAS 0X 12 SW
VEE2 4 11 VOUT2
1X 14 SW
13 X-COM
75
VIN3 5 6dB
AMP Driver 10 V+3 2X 15 SW
3X 11 SW
OUTPUT AMP VEE3 6 BIAS
9 VOUT3
0Y 1 SW

0
1Y 5 SW
6 0 -4.9
0.6 0.6 0 PowerSave 7 REF 8 GND
2Y 2 SW
3 Y-COM

0.6 3Y 4 SW
5.0 0
0 -4.9 0
5.0 0
IC351

0 -4.9
5.0 0 0

IC392: NJW1321FP1
2
Wide band video switch with I C bus

Y/R IN1
6dB Y/R OUT1
Y/R IN2
Y/R IN3
Y/R IN4
6dB Y/R OUT2

7 IC392
4.4

Pb OUT1

Pr OUT1

Y OUT2
Y OUT1
3.7 Pb/G IN1

Pb IN4
4.5

AUX3
AUX2

AUX1
AUX0
Y IN4

GND

GND
6dB Pb/G OUT1
Pb/G IN2

V+

V+
4.5 Pb/G IN3
Pb/G IN4
6dB Pb/G OUT2
4.3 3.7 38 25

GND 39 24 Pb OUT2
Pr IN4 PORT0
Page 111 C5 Pr/B IN1
V+
Y IN3
PORT1
Pr OUT2
6dB Pr/B OUT1
CB355 Pr/B IN2 GND V+
to FUNCTION (6)_CB297 Pr/B IN3 Pb IN3 VREF
V+ DGND
Pr/B IN4
COMPONENT 6dB Pr/B OUT2 Pr IN3
GND
Y IN2 48 15
GND
SDA
SCL
COMPONENT VIDEO

SELECTOR PORT 0 ADDRESS

1 14

PORT 1 SDA

Pr IN1
Pb IN1
Pr IN2
PORT 2

Y IN1
GND

GND

GND
Pb IN2

V+

V+
V+
SCL

ADR
PORT3
PORT2
I2C BUS AUX 0
PORT 3
8 V+ AUX 1

IC392 GND BIAS AUX 2

4.3 VREF AUX 3
3.7 DGND
4.5
4.5
4.3
3.7

Page 109 G2
to DIGITAL_CB81

9
IC392 CB356
4.3
3.7
4.2
4.3
4.3
3.7

10
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
VIDEO (2) ★ Components having special characteristics are marked s and must be replaced
with parts having specifications equal to those originally installed.
★ Schematic diagram is subject to change without notice.

115
 RX-V663/HTR-6160/DSP-AX763

■ REPLACEMENT PARTS LIST

• ELECTRICAL COMPONENT PARTS
WARNING
● Components having special characteristics are marked s and must be replaced with parts having specifications
equal to those originally installed.
● The chip resistor is not supplied as a replacement part.
* When a chip resistor is necessary, use the following part.
AAX60720: CHIP RESISTOR SAMPLE BOOK
s

ABBREVIATIONS IN THIS LIST ARE AS FOLLOWS:

C.A.EL.CHP : CHIP ALUMI.ELECTROLYTIC CAP L.EMIT : LIGHT EMITTING MODULE
C.CE : CERAMIC CAP LED.DSPLY : LED DISPLAY
C.CE.ARRAY : CERAMIC CAP ARRAY LED.INFRD : LED,INFRARED
C.CE.CHP : CHIP CERAMIC CAP MODUL.RF : MODULATOR,RF
C.CE.ML : MULTILAYER CERAMIC CAP PHOT.CPL : PHOTO COUPLER
C.CE.M.CHP : CHIP MULTILAYER CERAMIC CAP PHOT.INTR : PHOTO INTERRUPTER
C.CE.SAFTY : RECOGNIZED CERAMIC CAP PHOT.RFLCT : PHOTO REFLECTOR
C.CE.TUBLR : CERAMIC TUBULAR CAP PIN.TEST : PIN,TEST POINT
C.CE.SMI : SEMI CONDUCTIVE CERAMIC CAP PLST.RIVET : PLASTIC RIVET
C.EL : ELECTROLYTIC CAP R.ARRAY : RESISTOR ARRAY
C.MICA : MICA CAP R.CAR. : CARBON RESISTOR
C.ML.FLM : MULTILAYER FILM CAP R.CAR.CHP : CHIP RESISTOR
C.MP : METALLIZED PAPER CAP R.CAR.FP : FLAME PROOF CARBON RESISTOR
C.MYLAR : MYLAR FILM CAP R.FUS : FUSABLE RESISTOR
C.MYLAR.ML : MULTILAYER MYLAR FILM CAP R.MTL.CHP : CHIP METAL FILM RESISTOR
C.PAPER : PAPER CAPACITOR R.MTL.FLM : METAL FILM RESISTOR
C.PLS : POLYSTYRENE FILM CAP R.MTL.OXD : METAL OXIDE FILM RESISTOR
C.POL : POLYESTER FILM CAP R.MTL.PLAT : METAL PLATE RESISTOR
C.POLY : POLYETHYLENE FILM CAP RSNR.CE : CERAMIC RESONATOR
C.PP : POLYPROPYLENE FILM CAP RSNR.CRYS : CRYSTAL RESONATOR
C.TNTL : TANTALUM CAP R.TW.CEM : TWIN CEMENT FIXED RESISTOR
C.TNTL.CHP : CHIP TANTALUM CAP R.CEMENT : CEMENT RESISTOR
C.TRIM : TRIMMER CAP SCR.BND.HD : BIND HEAD B-TIGHT SCREW
CN : CONNECTOR SCR.BW.HD : BW HEAD TAPPING SCREW
CN.BS.PIN : CONNECTOR,BASE PIN SCR.CUP : CUP TIGHT SCREW
CN.CANNON : CONNECTOR,CANNON SCR.TERM : SCREW TERMINAL

RX-V663/HTR-6160/
CN.DIN : CONNECTOR,DIN SCR.TR : SCREW,TRANSISTOR

DSP-AX763
CN.FLAT : CONNECTOR,FLAT CABLE SUPRT.PCB : SUPPORT,P.C.B.
CN.POST : CONNECTOR,BASE POST SURG.PRTCT : SURGE PROTECTOR
COIL.MX.AM : COIL,AM MIX SW.TACT : TACT SWITCH
COIL.AT.FM : COIL,FM ANTENNA SW.LEAF : LEAF SWITCH
COIL.DT.FM : COIL,FM DETECT SW.LEVER : LEVER SWITCH
COIL.MX.FM : COIL,FM MIX SW.MICRO : MICRO SWITCH
COIL,OUTPT : OUTPUT COIL SW.PUSH : PUSH SWITCH
DIOD.ARRAY : DIODE ARRAY SW.RT.ENC : ROTARY ENCODER
DIODE.BRG : DIODE BRIDGE SW.RT.MTR : ROTARY SWITCH WITH MOTOR
DIODE.CHP : CHIP DIODE SW.RT : ROTARY SWITCH
DIODE.VAR : VARACTOR DIODE SW.SLIDE : SLIDE SWITCH
DIOD.Z.CHP : CHIP ZENER DIODE TERM.SP : SPEAKER TERMINAL
DIODE.ZENR : ZENER DIODE TERM.WRAP : WRAPPING TERMINAL
DSCR.CE : CERAMIC DISCRIMINATOR THRMST.CHP : CHIP THERMISTOR
FER.BEAD : FERRITE BEADS TR.CHP : CHIP TRANSISTOR
FER.CORE : FERRITE CORE TR.DGT : DIGITAL TRANSISTOR
FET.CHP : CHIP FET TR.DGT.CHP : CHIP DIGITAL TRANSISTOR
FL.DSPLY : FLUORESCENT DISPLAY TRANS : TRANSFORMER
FLTR.CE : CERAMIC FILTER TRANS.PULS : PULSE TRANSFORMER
FLTR.COMB : COMB FILTER MODULE TRANS.PWR : POWER TRANSFORMER ASS’Y
FLTR.LC.RF : LC FILTER,EMI TUNER.AM : TUNER PACK,AM
GND.MTL : GROUND PLATE TUNER.FM : TUNER PACK,FM
GND.TERM : GROUND TERMINAL TUNER.PK : FRONT-ENDTUNER PACK
HOLDER.FUS : FUSE HOLDER VR : ROTARY POTENTIOMETER
IC.PRTCT : IC PROTECTOR VR.MTR : POTENTIOMETER WITH MOTOR
JUMPER.CN : JUMPER CONNECTOR VR.SW : POTENTIOMETER WITH ROTARY SW
JUMPER.TST : JUMPER,TEST POINT VR.SLIDE : SLIDE POTENTIOMETER
L.DTCT : LIGHT DETECTING MODULE VR.TRIM : TRIMMER POTENTIOMETER
117
 RX-V663/HTR-6160/DSP-AX763

P.C.B. DIGITAL
RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
118
 RX-V663/HTR-6160/DSP-AX763

P.C.B. DIGITAL

RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
119
 RX-V663/HTR-6160/DSP-AX763

P.C.B. DIGITAL
RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
120
 RX-V663/HTR-6160/DSP-AX763

P.C.B. DIGITAL

RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
121
 RX-V663/HTR-6160/DSP-AX763

P.C.B. DIGITAL
RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
122
 RX-V663/HTR-6160/DSP-AX763

P.C.B. DIGITAL

RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
123
 RX-V663/HTR-6160/DSP-AX763

P.C.B. DIGITAL
RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
124
 RX-V663/HTR-6160/DSP-AX763

P.C.B. DIGITAL

RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
125
 RX-V663/HTR-6160/DSP-AX763

P.C.B. DIGITAL and P.C.B. FUNCTION

RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
126
 RX-V663/HTR-6160/DSP-AX763

P.C.B. FUNCTION

RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
127
 RX-V663/HTR-6160/DSP-AX763

P.C.B. FUNCTION
RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
128
 RX-V663/HTR-6160/DSP-AX763

P.C.B. FUNCTION

RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
129
 RX-V663/HTR-6160/DSP-AX763

P.C.B. FUNCTION

s
RX-V663/HTR-6160/
DSP-AX763

s
s

s
s
s
s
s

✻ New Parts
130
 RX-V663/HTR-6160/DSP-AX763

P.C.B. FUNCTION

s
s
s

RX-V663/HTR-6160/
DSP-AX763
s

✻ New Parts
131
 RX-V663/HTR-6160/DSP-AX763

P.C.B. FUNCTION and P.C.B. OPERATION

s
s
s
RX-V663/HTR-6160/

s
DSP-AX763

s
s
s
s
s

✻ New Parts
132
 RX-V663/HTR-6160/DSP-AX763

P.C.B. OPERATION

RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
133
 RX-V663/HTR-6160/DSP-AX763

P.C.B. OPERATION and P.C.B. MAIN

RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
134
 RX-V663/HTR-6160/DSP-AX763

P.C.B. MAIN

RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
135
 RX-V663/HTR-6160/DSP-AX763

P.C.B. MAIN
RX-V663/HTR-6160/
DSP-AX763

s
s

s
s

✻ New Parts
136
 RX-V663/HTR-6160/DSP-AX763

P.C.B. MAIN

s
s
s
s
s
s

RX-V663/HTR-6160/
s

DSP-AX763
s
s
s
s
s
s

s
s
s
✻ New Parts
137
 RX-V663/HTR-6160/DSP-AX763

P.C.B. MAIN

s
RX-V663/HTR-6160/
DSP-AX763

s
s
s
s
s
s
s
✻ New Parts
138
 RX-V663/HTR-6160/DSP-AX763

P.C.B. MAIN and P.C.B. VIDEO

s
s

s
s

RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
139
 RX-V663/HTR-6160/DSP-AX763

P.C.B. VIDEO
RX-V663/HTR-6160/
DSP-AX763

✻ New Parts
140
 RX-V663/HTR-6160/DSP-AX763

P.C.B. VIDEO Chip Resistors

Value 1/4W Type Part No. 1/6W Type Part No. Value 1/4W Type Part No. 1/6W Type Part No.
1.0 Ω HJ35 3100 HF85 3100 10 kΩ HF45 7100 HF45 7100
1.8 Ω HJ35 3180 ❊ 11 kΩ HF45 7110 HF45 7110
2.2 Ω HJ35 3220 HF85 3220 12 kΩ HJ35 7120 HF85 7120
3.3 Ω HJ35 3330 HF85 3330 13 kΩ HF45 7130 HF45 7130
4.7 Ω HJ35 3470 HF85 3470 15 kΩ HF45 7150 HF45 7150
5.6 Ω HJ35 3560 HF85 3560 18 kΩ HF45 7180 HF45 7180
10 Ω HF45 4100 HF45 4100 22 kΩ HF45 7220 HF45 7220
15 Ω HJ35 4150 HF85 4150 24 kΩ HF45 7240 HF45 7240
22 Ω HF45 4220 HF45 4220 27 kΩ HJ35 7270 HF85 7270
27 Ω HJ35 4270 HF85 4270 30 kΩ HF45 7300 HF45 7300
33 Ω HF45 4330 HF45 4330 33 kΩ HF45 7330 HF45 7330
39 Ω HJ35 4470 HF85 4390 36 kΩ HF45 7360 HF45 7360
47 Ω HF45 4470 HF45 4470 39 kΩ HF45 7390 HF45 7390
56 Ω HF45 4560 HF45 4560 47 kΩ HF45 7470 HF45 7470
68 Ω HF45 4680 HF45 4680 51 kΩ HF45 7510 HF45 7510
75 Ω HF45 4750 HF45 4750 56 kΩ HF45 7560 HF45 7560
82 Ω HF45 4820 HF45 4820 62 kΩ HF45 7620 HF45 7620
91 Ω HF45 4910 HF45 4910 68 kΩ HF45 7680 HF45 7680
100 Ω HF45 5100 HF45 5100 82 kΩ HF45 7820 HF45 7820
110 Ω HJ35 5110 HF85 5110 91 kΩ HF45 7910 HF45 7910
120 Ω HF45 5120 HF45 5120 100 kΩ HF45 8100 HF45 8100
150 Ω HF45 5150 HF45 5150 110 kΩ HF45 8110 HF45 8110
160 Ω HJ35 5160 ❊ 120 kΩ HF45 8120 HF45 8120
180 Ω HF45 5180 HF45 5180 150 kΩ HF45 8150 HF45 8150
200 Ω HF45 5200 HF45 5200 180 kΩ HF45 8180 HF45 8180
220 Ω HF45 5220 HF45 5220 220 kΩ HJ35 8220 HF85 8220
270 Ω HF45 5270 HF45 5270 270 kΩ HF45 8270 HF45 8270
330 Ω HF45 5330 HF45 5330 300 kΩ HF45 8300 HF45 8300
390 Ω HF45 5390 HF45 5390 330 kΩ HF45 8330 HF45 8330
430 Ω HF45 5430 HF45 5430 390 kΩ HJ35 8390 HF85 8390
470 Ω HF45 5470 HF45 5470 470 kΩ HF45 8470 HF45 8470
510 Ω HF45 5510 HF45 5510 560 kΩ HJ35 8560 HF85 8560
560 Ω HF45 5560 HF45 5560 680 kΩ HJ35 8680 HF85 8680
680 Ω HF45 5680 HF45 5680 820 kΩ HJ35 8820 HF85 8820
820 Ω HF45 5820 HF45 5820 1.0 MΩ HF45 9100 HF45 9100
910 Ω HF45 5910 HF45 5910 1.2 MΩ HJ35 9120 ❊
1.0 kΩ HF45 6100 HF45 6100 1.5 MΩ HJ35 9150 HF85 9150
1.2 kΩ HF45 6120 HF45 6120 1.8 MΩ HJ35 9180 HF85 9180
1.5 kΩ HF45 6150 HF45 6150 2.2 MΩ HJ35 9220 HF85 9220
1.8 kΩ HF45 6180 HF45 6180 3.3 MΩ HJ35 9330 HF85 9330
2.0 kΩ HJ35 6200 HF85 6200 3.9 MΩ HJ35 9390 ❊
2.2 kΩ HF45 6220 HF45 6220 4.7 MΩ HJ35 9470 HF85 9470
2.4 kΩ HJ35 6240 HF85 6240
2.7 kΩ HF45 6270 HF45 6270
3.0 kΩ HF45 6300 HF45 6300
3.3 kΩ HF45 6330 HF45 6330
1/4W Type
HF45
3.6 kΩ HJ35 6360 HF85 6360
1/4W Type 1/6W Type
3.9 kΩ HF45 6390 HF45 6390
HJ35 HF85
4.7 kΩ HF45 6470 HF45 6470 10mm
5mm
5.1 kΩ HF45 6510 HF45 6510
5.6 kΩ HF45 6560 HF45 6560
6.8 kΩ HF45 6680 HF45 6680
8.2 kΩ HF45 6820 HF45 6820
9.1 kΩ HF45 6910 HF45 6910

✻ New Parts ❊ : Not available

141
 A B C D E F G H I J

RX-V663/HTR-6160/DSP-AX763

• OVERALL ASS’Y

R, T, K, A, B, G, E, F models R, L models J model 103 160

103
156 130 16 U, C, R, T, K, A, B, G, E, F, L models
156
160
2 160
17 163
7 (2) 160 U, R, T, K, A, G, E, F, L models
160
160
160 R, T, K, A, B, G
160
E, F, L, J models
5 (2) 160 K model
5 (4)
160 R, T, K, A, B, G
176
E, F, L, J models
160 160 U, C models
167 103
3 171 7 (1)
172 155 160
5 (6) 160

7 (2) 5 (1) 135

160
133 155

27 5 (9)
101
170 170 28
Sub Chassis Unit 15 26
5 (3)
4 168 29 30
Front Panel Unit 171 173 155 167
163 163
12
163 155
U, C, R, T, K, A,
AMP Unit G, E, F, L, J models
167
168
B model
6 (1)
167 160
5
105 LEFT
163 121

122 155 200 R, T, A, L, J models

163 5 (5)
167
U, C, R,
203 T, L, J models

6 200-1

205 202 K, B, G,
203 K, A, G, E, F models E, F models
201 U, C models
120
163
139
U, C, R, T, K, A, 163
204 206 J model 163
G, E, F, L, J models 105 RIGHT

120
7 155 201-1 202-1
163

142
 RX-V663/HTR-6160/DSP-AX763

s
s
s
s
s
s
s
s
s
s
s
s
s

✻ New Parts ✻ New Parts 143

 A B C D E F G H I J

RX-V663/HTR-6160/DSP-AX763

• FRONT PANEL and SUB CHASSIS UNIT

U, C, R, T, K, A, G, E, F, L, J models 3-1 (1) 3-102

3-103 3-102
3-4 (1)
2 3-4 (3)
3-101 3-2

3-1 (2) 3-102

3-1 (6)

3 3-101 3-4 (4)

3-4 (5)
3-10
3-11 RX-V663
HTR-6160: C model HTR-6160: U, F models 3-1 (3)
DSP-AX763

3-11 B model
3-102
3-4 (6)

4 3-101 3-101

3-7 3-4 (1)

3-1 (4)

3-5 (3)
3-6 3-102
3-5 (1)
3-4 (2)
5 3-101

3-101

3-5 (2) 3-5 (4)

3-9 1-5 (1)

1-5 (4)

1-5 (2) HTR-6160: C model

1-5 (1)
DSP-AX763
6 1-40
1-5 (3)

1-5 (2)

1-1

1-1
144 ✻ New Parts
 A B C D E F G H I J

RX-V663/HTR-6160/DSP-AX763

• AMP UNIT
2-104
2-24 2-104

2-104

2
2-20
2-106

2-1 (2)

2-105

3
2-103

2-1 (1)
2-105

2-11
4

✻ New Parts 145

 A B C D E F G H I J

RX-V663/HTR-6160/DSP-AX763

1
■ REMOTE CONTROL
● RAV285 (U, C models)
• SCHEMATIC DIAGRAM • PANELS

+3V RAV285 (U, C models)

R3 64 60 65 67 63 62 66 61
REW REC FF SKIP+ PLAY PAUSE SKIP- STOP
2 100 ohms (SEARCH -) (SEARCH +)

44 40 45 47 43 42 46 41

100 k-ohms

100 k-ohms

100 k-ohms

470 ohms
LEFT RETURN ENTER VOL down DISPLAY RIGHT DOWN

R5

R4

R7
R6
33 36 34 39 38 35 37

1 2 4 3
D1 D2 J6
48 49 51 50
IR diode Red LED
LED D2 place under key21.
5 9 6 8 ENTER +10 7 0
U1 J5
52 56 53 55 59 58 54 57
3 ZLR32300H2832G
11 7 TITLE SCENE1 UP SCENE4 VOL up SCENE3 MENU SCENE2
P31 P07
J4
12 6 29 25 30 28 32 27 31 26
P32 P06
13 5 V-AUX/DOCK AMP D TV VOL - TV VOL + TV MUTE E TV INPUT
P33 P05
J3
14 4 17 21 18 24 20 23 19 22
P34 P04
15 23 DVD CD D-TV/CBL TV CH + TV CH - TUNER DVR MD/CD-R
P35 P03
Q1 J2
16 21 13 9 14 12 16 11 15 10
SMT P37 P02
R2 17 20
TV POWER A AV POWER MUTE POWER C STANDBY B
4 P36 P01
47 ohms J1
8 19 1 5 2 8 4 7 3 6
VDD P00
9 3
XTAL2 P27
10 2
X1 XTAL1 P26
8MHz 22 1
VSS P25
1 3
R1 C1 18
P30/Pref P24
28
1 ohm 47uF
24 27
P20 P23
2
25 26
5 P21 P22

RAV285
J1 X
J2 X
J3 X
J4 X
6 J5 X
J6 O

146
 RX-V663/HTR-6160/DSP-AX763

• KEY NO. LAYOUT • KEY CODE

Key Command AMP

No. Label key ID1 ID2
1 TV POWER – (TV POWER) (TV POWER) (TV POWER) (TV POWER) (TV POWER) (TV POWER) (TV POWER) – (TV POWER) (TV POWER) (TV POWER) TV POWER
1 2 3 4 2 AV POWER – (device) (device) 79-60 7F-80 D1-1B – 7C-80 (DVR POWER) 048.012 7F01-00 – (DVR POWER)
3 STANDBY O 7E-7F 7E-7F81 STANDBY
4 POWER O 7E-7E 7E-7E80 POWER
5 6 7 8
5 A O 7F01-3F 7F01-3FC1 A
6 B O 7A-B4 7A-B44A B
9 10 11 12 7 C O 7A-39 7A-39C7 C
8 MUTE O 7A-1C 7A-1CE2 MUTE
9 CD O 7A-15 7A-15EB CD
13 14 15 16 10 MD/CD-R O 7A-C9 7A-C937 MD/CD-R
11 TUNER O 7A-16 7A-16E8 TUNER
12 TV CH + – (TV CH +) (TV CH +) (TV CH +) (TV CH +) (TV CH +) (TV CH +) (TV CH +) – (TV CH +) (TV CH +) (TV CH +) (TV CH +)
17 18 19 20 13 DVD O 7A-C1 7A-C13F DVD
14 D-TV/CBL O 7A-54 7A-54AA DTV/CBL
15 DVR O 7A-13 7A-13ED DVR
21 22 23 24
16 TV CH - – (TV CH -) (TV CH -) (TV CH -) (TV CH -) (TV CH -) (TV CH -) (TV CH -) – (TV CH -) (TV CH -) (TV CH -) (TV CH -)
17 V-AUX/DOCK O 7A-55 7A-55AB V-AUX (/DOCK)
18 D O 7A-0F 7A-0FF1 VCR
25 26 27 28 19 E O 7A-14 7A-14EA PHONO
20 TV VOL + – (TV VOL +) (TV VOL +) (TV VOL +) (TV VOL +) (TV VOL +) (TV VOL +) (TV VOL +) – (TV VOL +) (TV VOL +) (TV VOL +) (TV VOL +)
21 AMP O Enter into AMP mode
9 10 11 (ID1) 11 (ID2) 13 14 15 17 18 19
29 31 V-AUX/DOCK VCR
30 CD MD/CD-R TUNER TUNER DVD DTV/CBL DVR PHONO
32 (TV INPUT) (TV INPUT) (TV INPUT) (TV INPUT)
22 TV INPUT – (TV INPUT) (TV INPUT) (TV INPUT) (TV INPUT) (TV INPUT) (TV INPUT) TV INPUT TV INPUT
23 TV MUTE – (TV MUTE) (TV MUTE) (TV MUTE) (TV MUTE) (TV MUTE) (TV MUTE) (TV MUTE) TV MUTE (TV MUTE) (TV MUTE) (TV MUTE) TV MUTE
33 34 35 24 TV VOL - – (TV VOL -) (TV VOL -) (TV VOL -) (TV VOL -) (TV VOL -) (TV VOL -) (TV VOL -) TV VOL - (TV VOL -) (TV VOL -) (TV VOL -) TV VOL -
25 SCENE 1 O 7A-007F 7A-007E SCENE SELECT
37 39
26 SCENE 2 O 7A-037C 7A-037D SCENE SELECT
36 38 27 SCENE 3 O 7A-0679 7A-0678 SCENE SELECT
28 SCENE 4 O 7A-0976 7A-0977 SCENE SELECT
29 TITLE – 7A-86 7A-8678 – – 7A-AE 7A-AE50 7C-B1 – 048.200 7F01-0D – –
40 41 42 43 30 UP – 7A-9D 7A-9D63 – – 7A-10 7A-10EE 7C-B4 – 048.088 7F01-0E – –
31 MENU – 7A-84 7A-847A – – 7A-AB 7A-AB55 7C-B2 – 048.084 7F01-0F – –
32 VOL up O 7A-1A 7A-1AE4 VOL UP
44 45 46 47 33 LEFT – 7A-9F 7A-9F61 – – 7A-AC 7A-AC52 7C-B5 – 048.090 7F01-10 – –
34 ENTER – 7A-DE 7A-DE20 – – 7A-AD 7A-AD53 7C-B8 – 048.092 7F01-11 – –
35 RIGHT – 7A-9E 7A-9E60 – – 7A-12 7A-12EC 7C-B6 – 048.091 7F01-12 – –
36 RETURN – 7A-AA 7A-AA54 – – 7A-AF 7A-AF51 7C-B7 – 048.131 7F01-13 – –
48 49 50 51 –
37 DOWN – 7A-9C 7A-9C62 – 7A-11 7A-11EF 7C-B3 – 048.089 7F01-14 – –
38 DISPLAY – 7A-C2 7A-C23C 79-0A 7F-9E 7A-B0 7A-B04E 7C-A6 – 048.015 7F01-15 – –
52 53 54 55
39 VOL down O 7A-1B 7A-1BE5 VOL DOWN
40 REC – (device) (device) 7A-4F – – – 7C-8B (DVR REC) 048.055 7F01-16 – (DVR REC)
56 57 58 59
41 STOP – (device) (device) 7A-09 7F-84 – – 7C-85 (DVR STOP) 048.049 7F01-1D – (DVR STOP)
42 PAUSE – (device) (device) 7A-09 7F-83 – – 7C-83 (DVR PAUSE) 048.048 7F01-1A – (DVR PAUSE)
43 PLAY – (device) (device) 7A-08 7F-82 – – 7C-82 (DVR PLAY) 048.044 7F01-1E – (DVR PLAY)
44 REW (SEARCH -) – (device) (device) 7A-0D 7F-88 7A-A4 7A-A45A 7C-86 (DVR REW) 048.041 7F01-17 – (DVR REW)
45 FF (SEARCH +) – (device) (device) 7A-0C 7F-89 7A-A5 7A-A55B 7C-87 (DVR FF) 048.040 7F01-18 – (DVR FF)
46 SKIP - – (device) (device) 7A-0B 7F-86 7A-A6 7A-A658 7C-B9 (DVR SKIP-) 048.033 7F01-1B – (DVR SKIP-)
47 SKIP + – (device) (device) 7A-0A 7F-87 7A-A7 7A-A759 7C-AB (DVR SKIP+) 048.032 7F01-1C – (DVR SKIP+)
48 1 – 7A-59 7A-59A7 79-11 7F-91 7A-E5 7A-E51B 7C-94 – 048.001 7F01-01 – –
49 2 – 7A-58 7A-58A6 79-12 7F-92 7A-E6 7A-E618 7C-95 – 048.002 7F01-02 – –
50 3 – 7A-94 7A-946A 79-13 7F-93 7A-E7 7A-E719 7C-96 – 048.003 7F01-03 – –
51 4 – 7A-8D 7A-8D73 79-14 7F-94 7A-E8 7A-E816 7C-97 – 048.004 7F01-04 – –
52 5 – 7A-56 7A-56A8 79-15 7F-95 7A-E9 7A-E917 7C-98 – 048.005 7F01-05 – –
53 6 – 7A-DD 7A-DD23 79-16 7F-96 7A-EA 7A-EA14 7C-99 – 048.006 7F01-06 – –
54 7 – 7A-95 7A-956B 79-17 7F-97 7A-EB 7A-EB15 7C-9A – 048.007 7F01-07 – –
55 8 – 7A-C4 7A-C43A 79-18 7F-98 7A-EC 7A-EC12 7C-9B – 048.008 7F01-08 – –
56 9 – 7A-87 7A-8779 79-19 7F-99 7A-B1 7A-B14F 7C-9C – 048.009 7F01-09 – –
57 0 – 7A-C3 7A-C33D 79-10 7F-90 7A-B2 7A-B24C 7C-93 – 048.000 7F01-0A – –
58 +10 – – – 79-1A 7F-9A – – 7C-9D – – 7F01-0B – –
59 ENTER – 7A-57 7A-57A9 79-0B 7F-8A 7A-B3 7A-B34D 7C-9E – – 7F01-0C – –

147
 A B C D E F G H I J

RX-V663/HTR-6160/DSP-AX763

● RAV330 (R, T, A, L, J models)

• SCHEMATIC DIAGRAM • PANELS
FORMAT : NEC FORMAT RAV330 (R, T, A, L, J models)
CARRIER FREQ. : 37.9 kHz
CARRIER DUTY : 1/3

MMST4403
Q1
2
TP26 27 31 35 39 42 45 48 52
PROG STRAIGHT MULTI CH IN LEVEL/BAND MEMORY INFO REC
1 5 9 TITLE RETURN
LTE3271TA TP25 28 32 36 40 43 46 49 53
LED1 PROG PURE DIRECT AUDIO PRESET/CH ENTER
R2 2 6 0
TP3 470 ohms TP24 13 29 33 37 44 50 54 56
MD ENHANCER 7 A-E/CAT. PRG SELECT SCENE
TP5 CD-R 3 +10 1
R1 TP23 17 30 34 38 41 47 51 55
PHONO SUR. DECODE PURE DIRECT SLEEP SET MENU/ DISPLAY PRG SELECT
1 ohm 4 8 ENT
SURCH MODE
MENU
TP22 26 23 20 16 12 8 4 9
MUTE VOLUME - VOLUME + VCR CD SIRIUS STANDBY A

TP21 25 22 19 15 11 7 3 5
R3 47 ohms TP6 TV INPUT TV CH - TV CH + DVR CBL XM AV POWER POWER
DTV
TP20 24 21 18 14 10 6 2 1
TV MUTE TV VOL - TV VOL + DVD DOCK TUNER TV POWER CODE SET
TP1 V-AUX
3 + TP19 59 58 57
SCENE SCENE SCENE
100µF 4 3 2
C1
TP17 TP16 TP15 TP14 TP13 TP12 TP11 TP10
TP2

560 ohms x 11
R14 R13 R12 R11 R10 R9 R8 R7 R6 R5 R4 33 32 31 30 29 28 27 26 25 24 23

P0.3/
INT3
P0.2/INT2

P0.1/INT1

P0.0/INT0

P4.4

P4.5

P4.6

P1.7

P1.6

P1.5

P1.4
34 P0.4/INT4 P1.3 22

35 P0.5/INT4 P1.2 21
4 36 P0.6/INT4 P1.1 20
LED12 LED11 LED10 LED9 LED8 LED7 LED6 LED5 LED4 LED3 LED2
37 P0.7/INT4 P4.7 19

38 P4.3 P3.3/TICAP 18
IC1
39 P4.2 P3.2/TOCK 17
S3F80JBBVB
P3.0/TOPWM/TOCAP/SDAT

40 P4.1 P1.0 16

41 P4.0 P2.7/INT9 15 LED14 R16

42 P2.0/INT5 P3.5 14
P3.1/REM/SCLK

43 P2.1/INT6 P3.4 13
P2.4/INT9

P2.5/INT9

44 P2.2/INT7 RESET 12 LED13 R15

XOUT

TEST
P2.3/

P2.6/
INT8

INT9
VDD

VSS

XIN

5
FUNCTION LED 1 2 3 4 5 6 7 8 9 10 11
LED3 TUNER

LED4 A TP4
TP30
LED5 MD/CDR AMP
SW1 SOURCE
LED6 V-AUX
TV
LED7 DTV/CBL TP31
LED8 CD

LED9 DVD

LED10 DVR SW1 AMP SOURCE TV

6 LED11 VCR P2.6 OPEN OPEN GND

LED12 PHONO P2.7 GND OPEN OPEN

0.1µF
LED13 B C2
X1
LED14 C

JP1 JP3
JP2 JP4

8MHz

JP1 JP2 JP3 JP4

7 RAV330 ON OFF OFF OFF

P2.3 VDD GND --- --- P2.4

148
 RX-V663/HTR-6160/DSP-AX763

• KEY LAYOUT • KEY CODE

Yamaha Receiver Yamaha LD Yamaha D-tuner Yamaha Misc Audio Yamaha DVD Yamaha DVD-R Yamaha Tape Universal CD-R Yamaha CD
1 LED2 No. Label ID1 ID2 [40127] [82915] R2915 [82918] R2918 [82176] [82981] M2981 [82982] M2982 [42543] Y2543 [52544] Y2544 [70542] [71292] [62907] D2907
MAIN ZONE2 MAIN ZONE2 N-1 N-2 N-2 N-2 N-1 P N-1 N-1
– TRANSMIT (LED)
2 3 4 5 1 CODE SET – – – –
4 STANDBY 7E-7F 7E-BB 7E-7F81 7E-BB45
5 POWER 7E-7E 7E-BA 7E-7E80 7E-BA44
6 7 8 9 6 TUNER 7A-16 7A-D2 7A-16E8 7A-D22C
LED3 LED4 LED13 LED14 7 A 7A-B4 7A-B8 7A-B44A 7A-B846
10 11 12 13 8 B 7A-39 7A-3A 7A-39C7 7A-3AC4
9 C 7F01-3F 7F01-40 7F01-3FC1 7F01-40BE
LED6 LED7 LED8 LED5
10 V-AUX/DOCK 7A-55 7A-D8 7A-55AB 7A-D826
14 15 16 17 11 DTV/CBL 7A-54 7A-D9 7A-54AA 7A-D927
LED9 LED10 LED11 LED12 12 CD 7A-15 7A-D1 7A-15EB 7A-D12F
13 MD/CD-R 7A-C9 7A-CF 7A-C937 7A-CF31
18 19 20 14 DVD 7A-C1 7A-CD 7A-C13F 7A-CD33
15 DVR 7A-13 7A-D7 7A-13ED 7A-D729
SW1 16 VCR 7A-0F 7A-D6 7A-0FF1 7A-D628
17 PHONO 7A-14 7A-D0 7A-14EA 7A-D02E
21 22 23 2 TV POWER
3 AV POWER D1-1B – 7F01-D0 7F01-00 7F01-20 7C-80 048-012 7F-80 79-60
18 TV VOL. up
24 25 26 19 TV CH up
20 VOL. up 7A-1A 7A-DA 7A-1AE4 7A-DA24
21 TV VOL. down
27 28 29 30 22 TV CH down
23 VOL. down 7A-1B 7A-DB 7A-1BE5 7A-DB25
24 TV MUTE
31 32 33 34 25 TV INPUT
26 MUTE 7A-1C 7A-DC 7A-1CE2 7A-DC22
27 PROG - 7A-59 7A-59A7 7C-17 7A-E5 7A-61 7F01-D1 7F01-01 7F01-21 7C-94 048.001 7F-91 79-11
35 36 37 38 28 PROG + 7A-58 7A-58A6 7C-18 7A-E6 7A-62 7F01-D2 7F01-02 7F01-22 7C-95 048.002 7F-92 79-12
29 ENHANCER 7A-94 7A-946A 7C-19 7A-E7 7A-63 7F01-D3 7F01-03 7F01-23 7C-96 048.003 7F-93 79-13
30 SUR.DECODE 7A-8D 7A-8D73 7C-1A 7A-E8 7A-64 7F01-D4 7F01-04 7F01-24 7C-97 048.004 7F-94 79-14
40 31 STRAIGHT 7A-56 7A-56A8 7C-1B 7A-E9 7A-65 7F01-D5 7F01-05 7F01-25 7C-98 048.005 7F-95 79-15
39 41
32 PURE DIRECT 7A-DD 7A-DD23 7C-1C 7A-EA 7A-66 7F01-D6 7F01-06 7F01-26 7C-99 048.006 7F-96 79-16
33 – 7A-95 7A-956B 7C-1D 7A-EB 7A-67 7F01-D7 7F01-07 7F01-27 7C-9A 048.007 7F-97 79-17
42 43 44 34 PARAMETER 7A-C4 7A-C43A 7C-1E 7A-EC 7A-68 7F01-D8 7F01-08 7F01-28 7C-9B 048.008 7F-98 79-18
35 MULTI CH IN 7A-87 7A-8779 7C-1F 7A-B1 7A-69 7F01-D9 7F01-09 7F01-29 7C-9C 048.009 7F-99 79-19
36 AUDUO SEL 7A-C3 7A-C33D 7C-16 7A-B2 7A-60 7F01-DA 7F01-0A 7F01-2A 7C-93 048.000 7F-90 79-10
45 46 47 37 – – – 7C-5D 7F01-DB 7F01-0B 7F01-2B 7C-9D 7F-9A 79-1A
38 SLEEP 7A-57 7A-57A9 7C-15 7A-B3 7A-BF 7F01-DC 7F01-0C 7F01-2C 7C-9E 7F-8A 79-0B
39 LEVEL 7A-86 7A-8678 7A-AE 7A-70 7F01-DD 7F01-0D 7F01-2D 7C-B1 048.200
48 49 50 51 40 Up 7A-9D 7A-9D63 7A-10 7A-6A 7F01-E1 7F01-0E 7F01-2E 7C-B4 048.088
41 SET MENU 7A-84 7A-847A 7A-AB 7A-6D 7F01-DE 7F01-0F 7F01-2F 7C-B2 048.084
42 Left 7A-9F 7A-9F61 7A-AC 7A-6E 7F01-E2 7F01-10 7F01-30 7C-B5 048.090
52 53 54 55 43 ENTER 7A-DE 7A-DE20 7A-AD 7A-6F 7F01-E3 7F01-11 7F01-31 7C-B8 047.092
44 Right 7A-9E 7A-9E60 7A-12 7A-6C 7F01-E4 7F01-12 7F01-32 7C-B6 048.091 7A-06
45 RETURN 7A-AA 7A-AA54 7A-AF 7A-71 7F01-DF 7F01-13 7F01-33 7C-B7 048.131
56 57 58 59 46 Down 7A-9C 7A-9C62 7A-11 7A-6B 7F01-E5 7F01-14 7F01-34 7C-B3 048.089
47 DISPLAY 7A-C2 7A-C23C 7C-13 7A-B0 7A-72 7F01-E0 7F01-15 7F01-35 7C-A6 048.015 7F-9E 79-0A
48 REW (Search) 7C-06 7A-A4 7A-3D 7F01-EA 7F01-17 7F01-37 7C-86 048.041 7A-01 7F-88 7A-0D
49 FF (Search) 7C-07 7A-A5 7A-3E 7F01-EB 7F01-18 7F01-38 7C-87 048.040 7A-02 7F-89 7A-0C
50 CHP/Skip- 7C-02 7A-A6 7A-3F 7F01-EC 7F01-1B 7F01-3B 7C-B9 048.033 7A-07 7F-86 7A-0B
51 CHP/Skip+ 7C-03 7A-A7 7A-EF 7F01-ED 7F01-1C 7F01-3C 7C-BA 048.032 7A-40 7F-87 7A-0A
52 REC 7F01-E6 7F01-16 7F01-36 7C-8B 048.055 7A-04 7A-4F
53 Stop 7C-5B 7F01-E9 7F01-1D 7F01-3D 7C-85 048.049 7A-03 7F-84 7A-09
54 Pause 7C-5A 7F01-E7 7F01-1A 7F01-3A 7C-83 048.048 7F-83 7A-09
55 Play 7C-05 7F01-E8 7F01-1E 7F01-3E 7C-82 048.044 7A-00 7F-82 7A-08
56 SCENE1 7A-007F 7A-017E 7A-007E 7A-017F
57 SCENE2 7A-037C 7A-047B 7A-037D 7A-047A
58 SCENE3 7A-0679 7A-0778 7A-0678 7A-0779
59 SCENE4 7A-0976 7A-0A75 7A-0977 7A-0A74

Mode Default Device

Receiver (Slide switch-AMP) 00001-Yamaha Receiver
CD (Default-slide switch Source) 62907-Yamaha CD
MD/CD 71292-Yamaha CD-R
XM 82918-Yamaha Digital Tuner *1
SIRIUS 82176-Yamaha Digital Tuner *1
DVD 42543-Yamaha DVD
DTV/CBL None (can be set as a DVD, DVD-R, VCR, PVR, TV, CBL, SAT, LD, CD, CD-R, MD, Tape and Tuner)
TUNER 82915-Yamaha Tuner
VCR None (can be set as a DVD, DVD-R, VCR, PVR, TV, CBL, SAT, LD, CD, CD-R, MD, Tape and Tuner)
DVR 52544-Yanmaha DVD-R
V-AUX/DOCK 82981-Yamaha MISC Audio
NET 82982-Yamaha MISC Audio
PHONO None (can be set as a DVD, DVD-R, VCR, PVR, TV, CBL, SAT, LD, CD, CD-R, MD, Tape and Tuner)
TV (slide switch-TV) N/A
Note *1: Default ID will vary upon jumper setting.

149
 A B C D E F G H I J

RX-V663/HTR-6160/DSP-AX763

● RAV372 (K, B, G, E, F models)

• SCHEMATIC DIAGRAM • PANELS

VBAT VDD TV RAV372 (K, B, G, E, F models)

AMP
SOURCE
VDD VDD
VDD VDD

3007
10K
Spring+
470K
0028 3001

270K

270K
3011

3012
2006 7017
7002
2 VDD 7011 5002 1
VSS VDD
32
100n BC875B
4 x AAA Batteries BC857B 8MHZ 2 31

3006
10K
7009 XIN P3.1/...
3 30 3019
BC847B 7010 VDD XOUT P3.0/... VBAT
3002 6003 4
TEST P2.4/INT9
29 10K
BC847B

3-way switch
1M LTL-N709E- 5 28

1
2

3
4
072A 3005 P2.5/INT9 P2.3/INT8
6 27

1004
7008 100K P2.6/INT9 P2.2/INT7
7 26

3008
2K2
Spring- BC847B + VDD RESET P2.1/INT6
180K
3003

2001 2002 8 25 7016 7015

3106
P2.7/INT9 P2.0/INT5 3020

10K
0029 100n 9 24
470µ P1.0 P0.7/INT4 10K BC807-25 BC807-25
2005

3004
10 23

10K
100n P1.1 P0.6/INT4

270K
3009
11 22
P1.2 P0.5/INT4

100K
3017
Optional 12 21
1005 P1.3 P0.4/INT4 7012
13 20

2-way switch
Backlight P1.4 P0.3/INT3
switch 14 19 BC857B 7014
P1.5 P0.2/INT2

1003
15
P1.6 P0.1/INT1
18 BC847B Learn input
16 17

3
2
1
31 26 27 29 30 28 P1.7 P0.0/INT0
MUTE TV VOL - TV CH - TV MUTE TV INPUT VOLUME -
8 VDD S3C80F9XZO 3014 6002 6001
3 3013 4K7 LET-3217 LET-3271
7001 10K

3015
10K
20 13 9 10 14 15 19
PHONO V-AUX/DOCK TUNER A DTV/CBL CD VCR
31 12
11 P00 VDD

3018

3025
5R8

5R8
32 13
P01 VDD 2004
35 1
63 64 60 61 65 62 67 P02 P02 R/W 100n
MACRO REC LEARN RENAME 41 23 3036
33 P03 AS VDD 10K
5 47
P04 DS
7 29
59 52 56 57 53 58 54 P05 P05 PREF1 7013 Carrier
SEEK-START MULTI CH IN INFO EON 0 MODE-PTY +10 8 17
9 34 P06 XTAL2 BC857B
11 18
P07 XTAL1 VDD 7022
33 25
51 48 45 50 49 46 55 P10 RESET 2016 BC847B
34 24 3037
PARAMETER STEREO LIVE/CLUB SUR. DECODE ENHANCER ENTERTAIN SLEEP P11 Vss 2003 100n 100K
8 5 2 7 6 3 ENT 39 39 37
P12 Vss 1µF 5001
40 38 7019
P13 Vss 8MHZ
47 44 41 38 37 42 43 9 6 BC857B 3030

3038
P14 N/C

10K
MOVIE CLASSICAL ENTER DISPLAY STRAIGHT
4 1 40 10 14 10K
P15 N/C

3043
3039

3041

10K
47K

47K
15 30

LM393D

LM393D
P16 N/C

7005A
3032

7005B
16 36 Reset 3029 10K
34 P17 N/C SCL 2021
4 35 40 36 33 32 SET MENU/
39
Learn input

8
AUDIO MENORY PRESET/CH LEVEL/BAND SRCH MODE PURE DIRECT
Carrier
42 48 47K 3040 100n
P20 N/C 3

8
RETURN TITLE MENU 9 43 19 3027 470R
P21 P31 Envelop 3033 + 1 6
44 20 2K7 2 - - 7
P22 P32 5 + Envelop

BC847B
21 17 23 24 18 22 25 45 21 1K 6004

4
SELECT DVD TV VOL + TV CH + DVR SELECT VOLUME + P23 P33 PMLL4148L

2019

3042

2020
100n
2015

150K
10 46 22

4
3028

7020

2017

2018
100n
3035

47K
2n2
27K
P24 P34

2n2
2 26 100n
P25 P35
8 11 5 6 7 16 12 3 28 Backlight
4 B 1 2 3 MD/CD-R C P26 P36
15 4 27
P27 P37 SCL
SDA
4 1 2 3 66 SDA
POWER TV POWER AV POWER STANDBY CLEAR
16 Z86L87/89/73
VDD
21 3 2 46 45 44 43
270K

Jumper option
3024

2007 3022
VDD 100n 2k7
7003 (U2)
5 1 8
3075

A0 VCC
1M

2 7 7004
VDD A1 WP
3 6 PCF8566
A2 SCL
P02 4 5 1 17
GND SDA SDA S0
3077 3076

2 18
1M

SCL S1
7 19
P05 A0 S2
8 20
A1 S3
1M

9 21
A2 S4
10 22
SA0 S5
23

LCD Driver 4x24 Segments

S6
VBAT 3 24
Optional Sync S7
4 25
CLK S8
6 26
VDD OSC S9
2008 27
S10
3044

3046

3048

3050

3052

3054

3056

3058

3060

3062

3064

3066

3068

3070
1K2

1K2

1K2

1K2

1K2

1K2

1K2

1K2

1K2

1K2

1K2

1K2

1K2

1K2

VE2 100n 5 28
VDD VDD S11
11 29
Vss S12
3045

3047

3049

3051

3053

3055

3057

3059

3061

3063

3065

3067

3069
1K2

1K2

1K2

1K2

1K2

1K2

1K2

1K2

1K2

1K2

1K2

1K2

1K2

1006 12 30
Vlod S13
3023

HEADER 3x2
1M

31

S10
S0
S1
S2
S3
S4
S5
S6
S7
S8
S9
1 2 S14
6 32
6005

6007

6009

6011

6013

6015

6017

6019

6021

6023

6025

6027

6029

6031

3 4 S15

1
2
3
4
5
6
7
8
9
10
11
SDA 33
5 6 S16
Reset SCL 34
6006

6008

6010

6012

6014

6016

6018

6020

6022

6024

6026

6028

6030

S17
35 5003
2009 S18 LCD Module
13 36
100n BP0 S19
14 37
BP2 S20
15 38

22
21
20
19
18
17
16
15
14
13
12
BP1 S21
Backlight 16 39
7818 BP3 S22

BP0
BP1
BP2
BP3
S17
S16
S15
S14
S13
S12
S11
3021 BC817-25 40
10K S23

150
 RX-V663/HTR-6160/DSP-AX763

• KEY LAYOUT • KEY CODE

AMP library 2001 (default) AMP library 2002
No. Label Area Learn Macro Luminous
MAIN ZONE2 ZONE3 ALL MAIN ZONE2 ZONE3 ALL
- LED – – – – – – – – – – – – Linked with IR signal LCD Display Default Preset
SW2 (MACRO ON/OFF) OFF ON 5 letters 3 letters Library Brand Brand No.
1 2 3 4 3 STANDBY 1 O O O 7E-7F 7E-BB 7A-EE 7A-1E 7E-7F81 7E-BB45 7A-EE10 7A-1EE0 Power STANDBY Macro feature STB
4 POWER on 1 O O O 7E-7E 7E-BA 7A-ED 7A-1D 7E-7E80 7E-BA44 7A-ED13 7A-1DE3 Power ON Macro feature PWR
5 6 7 8
5 SCENE 1 1 O – O 7A-007F 7A-017E 7A-027D 7A-007E 7A-017F 7A-027C Output IR signal & Change device mode
6 SCENE 2 1 O – O 7A-037C 7A-047B 7A-057A 7A-037D 7A-047A 7A-057B Output IR signal & Change device mode
9 10 11 12 7 SCENE 3 1 O – O 7A-0679 7A-0778 7A-0877 7A-0678 7A-0779 7A-0876 Output IR signal & Change device mode
8 SCENE 4 1 O – O 7A-0976 7A-0A75 7A-0B74 7A-0977 7A-0A74 7A-0B75 Output IR signal & Change device mode
9 TUNER 1 O O – 7A-16 7A-D2 7A-F3 7A-16E8 7A-D22C 7A-F30D Output IR signal & Change device mode Macro feature & Change device mode TUNER TUN TUNER YAMAHA3 2602
13 14 15 16
10 A 1 O O – 7A-B4 7A-B8 7A-B9 7A-B44A 7A-B846 7A-B947 Output IR signal & Change device mode Macro feature & Change device mode XM XM TUNER YAMAHA5 2604
1 O O – – – – – – – Change device mode Macro feature & Change device mode TAPE TAPE TAPE YAMAHA1 2700
17 18 19 20 11 B 1 O O – 7A-39 7A-3A 7A-3B 7A39C7 7A-3AC4 7F3BC5 Output IR signal & Change device mode Macro feature & Change device mode SAT SAT TUNER YAMAHA9 NEW-1
1 O O – – – – – – – Change device mode Macro feature & Change device mode LD LD LD YAMAHA 2200
12 C 1 O O – 7F01-3F 7F01-40 7F01-41 7F01-3FC1 7F01-40BE 7F01-40BF Output IR signal & Change device mode Macro feature & Change device mode USB USB TUNER YAMAHA8 2607
21 1 O O – 7F01-3F 7F01-40 7F01-41 7F01-3FC1 7F01-40BE 7F01-40BF Output IR signal & Change device mode Macro feature & Change device mode NET NET TUNER YAMAHA8 2607
13 V-AUX/DOCK 1 O O – 7A-55 7A-D8 7A-F0 7A-55AB 7A-D826 7A-F00E Output IR signal & Change device mode Macro feature & Change device mode V-AUX AUX TUNER YAMAHA7 2606
22 14 DTV/CBL 1 O O – 7A-54 7A-D9 7A-F6 7A-54AA 7A-D927 7A-F608 Output IR signal & Change device mode Macro feature & Change device mode DTV DTV TV nothing nothing
15 CD 1 O O – 7A-15 7A-D1 7A-F2 7A-15EB 7A-D12F 7A-F20C Output IR signal & Change device mode Macro feature & Change device mode CD CD CD YAMAHA1 2300
16 MD/CD-R 1 O O – 7A-C9 7A-CF – 7A-C937 7A-CF31 – Output IR signal & Change device mode Macro feature & Change device mode CD-R CDR CD-R YAMAHA 2400
23 24 25 17 DVD 1 O O – 7A-C1 7A-CD 7A-FC 7A-C13F 7A-CD33 7A-FC02 Output IR signal & Change device mode Macro feature & Change device mode DVD DVD DVD YAMAHA1 2100
18 DVR 1 O O – 7A-13 7A-D7 7A-FA 7A-13ED 7A-D729 7A-FA04 Output IR signal & Change device mode Macro feature & Change device mode DVR DVR DVR YAMAHA 2807
19 VCR 1 O O – 7A-0F 7A-D6 7A-F9 7A-0FF1 7A-D628 7A-F907 Output IR signal & Change device mode Macro feature & Change device mode VCR VCR VCR nothing nothing
26 27 28 20 PHONO 1 O O – 7A-14 7A-C0 7A-F1 7A-14EA 7A-D02E 7A-F10F Output IR signal & Change device mode Macro feature & Change device mode PHONO PHO TV nothing nothing
21 SELECT up 1 – – O – – – – – – – – Select device mode (up)
29 30 31 22 SELECT down 1 – – O – – – – – – – – Select device mode (down)
SW1 (AMP/SOURCE/TV) AMP SOURCE TV
9 10 11 12 13 14 15 16 17 18 19 20 Option
32 33 34 35 TUNER XM TAPE SAT LD NET V-AUX/DOCK DTV/CBL CD MD/CD-R DVD DVR VCR PHONO OPTN
1 TV POWER 16 O – O – – – – – – – – – – – – – – – – – –
2 AV POWER 16 O – O Punch to SOURCE Punch to SOURCE D1-1B – – 7F01-D0 – 7F01-20 7F01-00 – 79-60 7F-80 7C-80 AA5A A5AA – – – PunchtoSOURCE

36 37 38 39 23 TV VOL up 16 O – O – – – – – – – – – – – – – – – – – –
24 TV CH up 16 O – O – – – – – – – – – – – – – – – – – –
25 VOL up 1 O – O 7A-1A 7A-DA 7A-FD 7A-1AE4 7A-DA24 7A-FD03 Punch to AMP mode
40 41 42 43 26 TV VOL down 16 O – O – – – – – – – – – – – – – – – – – –
27 TV CH down 16 O – O – – – – – – – – – – – – – – – – – –
28 VOL down 1 O – O 7A-1B 7A-DB 7A-FE 7A-1BE5 7A-DB25 7A-FE00 Punch to AMP mode
44 45 46 47 29 TV mute 16 O – O – – – – – – – – – – – – – – – – – –
30 TV input 16 O – O – – – – – – – – – – – – – – – – – –
31 MUTE 1 O – O 7A-1C 7A-DC 7A-FF 7A-1CE2 7A-DC22 7A-FE01 Punch to AMP mode
48 49 50 51 32 TITLE 16 O – O 7A-86 – – 7A-8678 – – 7A-AE 7A-70 – 7F01-DD – 7F01-2D 7F01-0D – – – 7C-B1 AA5A A9A5 – – – –
33 Up 16 O – O 7A-9D – – 7A-9D63 – – 7A-10 7A-6A – 7F01-E1 – 7F01-2E 7F01-0E – – – 7C-B4 AA5A A966 – – – –
52 53 54 55 34 MENU 16 O – O 7A-84 – – 7A-847A – – 7A-AB 7A-6D – 7F01-DE – 7F01-2F 7F01-0F – – – 7C-B2 AA5A A A666 – – – –
35 AUDIO 16 O – O 7A-C3 – – 7A-C33D – – – – – 7F01-EE 7C-12 7F01-39 7F01-19 – – – 7C-AD AA5A 95A5 – – – –
36 Left 16 O – O 7A-9F – – 7A-9F61 – – 7A-AC 7A-6E – 7F01-E2 – 7F01-30 7F01-10 – – – 7C-B5 AA5A 9966 – – – –
56 57 58 59 37 ENTER 16 O – O 7A-DE – – 7A-DE20 – – 7A-AD 7A-6F – 7F01-E3 – 7F01-31 7F01-11 – – – 7C-B8 AA5A A566 – – – –
38 Right 16 O – O 7A-9E – – 7A-9E60 – – 7A-12 7A-6C 7A-06 7F01-E4 – 7F01-32 7F01-12 – – – 7C-B6 AA5A 5966 – – – –
60 61 62 63 39 PURE DIRECT 1 O – O 7A-DD – – 7A-DD23 – – Punch to AMP mode
40 RETURN 16 O – O 7A-AA – – 7A-AA54 – – 7A-AF 7A-71 – 7F01-DF – 7F01-33 7F01-13 – – – 7C-B7 AA5A 5AA9 – – – –
41 Down 16 O – O 7A-9C – – 7A-9C62 – – 7A-11 7A-6B – 7F01-E5 – 7F01-34 7F01-14 – – – 7C-B3 AA5A 6966 – – – –
64 65 66 67
42 DISPLAY 16 O – O 7A-C2 – – 7A-C23C – – 7A-B0 7A-72 – 7F01-E0 7C-13 7F01-35 7F01-15 – 79-0A 7F-9E 7C-A6 AA5A 55AA – – – –
43 STRAIGHT 1 O – O 7A-56 – – 7A-56AB – – Punch to AMP mode
44 1 16 O – – 7A-88 – – 7A-8876 – – 7A-E5 7A-61 – 7F01-D1 7C-17 7F01-21 7F01-01 – 79-11 7F-91 7C-94 AA5A 6AAA – – – –
45 2 16 O – – 7A-89 – – 7A-8977 – – 7A-E6 7A-62 – 7F01-D2 7C-18 7F01-22 7F01-02 – 79-12 7F-92 7C-95 AA5A 9AAA – – – –
46 3 16 O – – 7A-8A – – 7A-8A74 – – 7A-E7 7A-63 – 7F01-D3 7C-19 7F01-23 7F01-03 – 79-13 7F-93 7C-96 AA5A 5AAA – – – –
47 4 16 O – – 7A-8B – – 7A-8B75 – – 7A-E8 7A-64 – 7F01-D4 7C-1A 7F01-24 7F01-04 – 79-14 7F-94 7C-97 AA5A A6AA – – – –
48 5 16 O – – 7A-8C – – 7A-8C72 – – 7A-E9 7A-65 – 7F01-D5 7C-1B 7F01-25 7F01-05 – 79-15 7F-95 7C-98 AA5A 66AA – – – –
49 6 16 O – – 7A-94 – – 7A-946A – – 7A-EA 7A-66 – 7F01-D6 7C-1C 7F01-26 7F01-06 – 79-16 7F-96 7C-99 AA5A 96AA – – – –
50 7 16 O – – 7A-8D – – 7A-8D73 – – 7A-EB 7A-67 – 7F01-D7 7C-1D 7F01-27 7F01-07 – 79-17 7F-97 7C-9A AA5A 56AA – – – –
51 8 16 O – – 7A-C4 – – 7A-C43A – – 7A-EC 7A-68 – 7F01-D8 7C-1E 7F01-28 7F01-08 – 79-18 7F-98 7C-9B AA5A A9AA – – – –
52 9 16 O – – 7A-87 – – 7A-8779 – – 7A-B1 7A-69 – 7F01-D9 7C-1F 7F01-29 7F01-09 – 79-19 7F-99 7C-9C AA5A 69AA – – – –
53 0 16 O – – 7A-95 – – 7A-956B – – 7A-B2 7A-60 – 7F01-DA 7C-16 7F01-2A 7F01-0A – 79-10 7F-90 7C-93 AA5A AAAA – – – –
54 +10 16 O – – – – – – – – – – – 7F01-DB 7C-5D 7F01-2B 7F01-0B – 79-1A 7F-9A 7C-9D – – – – –
55 ENT 16 O – – 7A-57 – – 7A-57A9 – – 7A-B3 7A-BF – 7F01-DC 7C-15 7F01-2C 7F01-0C – 79-0B 7F-8A 7C-9E – – – – –
56 REW (SEARCH) 16 O – – Punch to SOURCE Punch to SOURCE 7A-A4 7A-3D 7A-01 7F01-EA 7C-06 7F01-37 7F01-17 – 7A-0D 7F-88 7C-86 AA5A 699A – – – Punch to SOURCE

57 FF (SEARCH) 16 O – – Punch to SOURCE Punch to SOURCE 7A-A5 7A-3E 7A-02 7F01-EB 7C-07 7F01-38 7F01-18 – 7A-0C 7F-89 7C-87 AA5A A99A – – – PunchtoSOURCE

58 CHP/SKIP- 16 O – – Punch to SOURCE Punch to SOURCE 7A-A6 7A-3F 7A-07 7F01-EC 7C-02 7F01-3B 7F01-1B – 7A-0B 7F-86 7C-B9 AA5A 6A9A – – – PunchtoSOURCE

59 CHP/SKIP+ 16 O – – Punch to SOURCE Punch to SOURCE 7A-A7 7A-EF 7A-40 7F01-ED 7C-03 7F01-3C 7F01-1C – 7A-0A 7F-87 7C-BA AA5A AA9A – – – PunchtoSOURCE

60 REC 16 O – – Punch to SOURCE Punch to SOURCE – – 7A-04 7F01-E6 – 7F01-36 7F01-16 – 7A-4F – 7C-8B AA5A 565A – – – PunchtoSOURCE

61 STOP 16 O – – Punch to SOURCE Punch to SOURCE – – 7A-03 7F01-E9 7C-5B 7F01-3D 7F01-1D – 7A-09 7F-84 7C-85 AA5A 6A5A – – – PunchtoSOURCE

62 PAUSE 16 O – – Punch to SOURCE Punch to SOURCE – – – 7F01-E7 7C-5A 7F01-3A 7F01-1A – 7A-09 7F-83 7C-83 AA5A AA5A – – – PunchtoSOURCE

63 PLAY 16 O – – Punch to SOURCE Punch to SOURCE – – 7A-00 7F01-E8 7C-05 7F01-3E 7F01-1E – 7A-08 7F-82 7C-82 AA5A A59A – – – PunchtoSOURCE

64 MACRO – – – – – can not use – can not use Change to MACRO mode
65 LEARN – – – – – can not use – can not use Change to LEARNING or PRESET mode
66 CLEAR – – – – – can not use – can not use Change to CLEAR mode (Macro clear, Rename clear, Preset clear, All key clear)
67 RE-NAME – – – – – can not use – can not use Change to RE-NAME mode
151
152
REMOTE CONTROL RAV285
RX-V663/HTR-6160/DSP-AX763

REMOTE CONTROL RAV285 REMOTE CONTROL RAV330

 REMOTE CONTROL RAV330 REMOTE CONTROL RAV372

REMOTE CONTROL RAV372

RX-V663/HTR-6160/DSP-AX763

153
 RX-V663/HTR-6160/DSP-AX763

154
RX-V663/HTR-6160/DSP-AX763

155
RX-V663/HTR-6160/
DSP-AX763