G+ Universal Control Box Instruction Manual

10 Jan, 2014

Control Box Housing

Control Box Cover

Courtesy Light

Control Box Push Button

PCB Index

Page 1 of 7
 G+ Universal Control Box Instruction Manual
10 Jan, 2014

1 TR Transformer Connector
2 MOTOR Motor Drive Unit Connector
3 15A FUSE Protection Fuse
4 EXPOS External Door Position Signal Connector
5 EXLAMP External Light Connector
6 COUNT External Counter Connector
7 EXSW Panel Push Button Connector (Single button control)
8 PANEL Panel Push Button Connector (Three button control)
9 TEST On-Board Control
10 EXCON External I/O Terminal
11 FORCE Force Setting
12 AUTO CLOSE Auto Close Setting
13 DOOR SIZE Door Size Setting
14 BUZZER Buzzer Setting
15 MODE Mode Setting
16 1KEY/3KEYS Transmitter Key Settings
17 LEARN Transmitter Learn
18 WIRELESS P/CELL Wireless Photocell Connector
19 ALARM/DISP External Alarm or Count-Down Display Connector
20 JP1/JP2 LED Board Connector
21 EAS EAS Receiver Connector
22 POWER Power LED Indicator
23 LED2 Transmitter Learn LED Indicator
24 BZ Buzzer

Door Size Setting

Jumper configuration for residential doors

Jumper configuration for commercial doors

Page 2 of 7
 G+ Universal Control Box Instruction Manual
10 Jan, 2014

Force Setting

1. [FORCE] is factory preset at 3

2. To reduce the door operation force, turn the [FORCE] pot clockwise by one interval, i.e. from
Force setting 3 to 2, or Force setting 2 to 1
3. Now test the door on a block of wood 40mm off the ground. The door should reverse. If the
door doesn’t auto reverse, go to step 2 to further reduce the force setting and retest

Transmitter Coding – By Controller

1. Press [LEARN] button once

2. [LED2] will light with 3 beeps
3. Press the desired operation key on transmitter
4. LED will blink with beep to signal successful programming. If an attempt is made to program
an existing transmitter in memory, error is signaled by 2 beeps.
5. Unit will automatically exit the setup after 3 seconds

Transmitter Coding – By Transmitter

1. Using an already programmed transmitter, press and hold

OPEN & STOP keys simultaneously for 3 seconds
2. Unit will beep three times to signal for Learn Mode [KEY1] STOP
3. Press the desired operation key on the new transmitter
[KEY2] OPEN
4. A beep will signal for successful coding. Two beeps signal for a
transmitter already in memory [KEY3] CLOSE
5. Unit will automatically exit the setup after 3 seconds

Transmitter Code Erase

1. Press and hold [LEARN] button for 10 seconds

2. While LED diminishes and 3 beeps are heard, all codes have been erased

Page 3 of 7
 G+ Universal Control Box Instruction Manual
10 Jan, 2014

Transmitter Key Setting

Jumper configuration for single key operation [KEY1] STOP

[KEY2] OPEN
Jumper configuration for 3 keys operation
[KEY3] CLOSE
Buzzer Setting

Jumper configuration to turn buzzer on

Jumper configuration to turn buzzer off

Mode Setting

Jumper configuration ON for driveway mode:

1. Courtesy light will only illuminate during operation and go out once stop.
2. ALARM/DISP becomes the signal output terminal of a Count-Down Display if it is connected.
3. When automatic close is set, courtesy light and external light will light up 5 seconds before
closing.
Auto Close Setting
To program to automatically close after the door has been opened.
* Time setting:
1 2 3

10" 20" 40" SEC

OFF

ON 10"

ON 20"

ON ON 30"

ON 40"

ON ON 50"

ON ON 60"

ON ON ON 70"

Page 4 of 7
 G+ Universal Control Box Instruction Manual
10 Jan, 2014

LED Control

Under 3 Keys transmitter mode, the LED can be switched on and off using the STOP key. This will
also output to the EXLAMP terminal onboard.
Vacation Mode

Transmitter signal can be locked out by pressing STOP & CLOSE keys simultaneously on the
transmitter. To deactivate, press the same keys again.

Key Ring Transmitter

Plastic Strip

Battery Type 3V CR2016x2 (Lithium Cell)

To replace batteries:
1. Remove the screw on the back case.
2. Replace the old batteries with new ones (3V CR2016x2) and ensure plastic strip remain intact
in clip.
3. Locate back of case and secure with screw.

Page 5 of 7
 G+ Universal Control Box Instruction Manual
10 Jan, 2014

Photo Sensor Connection Diagram

External Wall Switch Connection Diagram

Page 6 of 7
 G+ Universal Control Box Instruction Manual
10 Jan, 2014

External Light Connection Diagram

(Optional Interface Board Required)

Page 7 of 7
The Glidermatic brand and its complete product range is wholly owned and operated by Gliderol Garage Doors.

Manufacturers Product Warranties Statement

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure.

In addition, we offer our Gliderol Warranty as set out below. The benefits given to you by our Gliderol Warranty are in addition to other rights and remedies
you may have under the Australian Consumer Law. Our Gliderol Warranty does not exclude, restrict or modify any such statutory rights or remedies which
cannot be excluded.

For products sold and installed by Gliderol, the Gliderol Warranty extends to cover defects of manufacture and costs of delivery and/or re-installation of any
product repaired or replaced under the terms of the Gliderol Warranty. In all other circumstances, where the products are supplied by a third party, the
Gliderol Warranty covers defects of manufacture only and does not include costs of reinstallation or delivery.

This is not intended to exclude, restrict or modify any right or remedy to which you may otherwise be entitled in respect of delivery or re-installation under
the Australian Consumer Law.

Schedule of Warranty Period for Individual Components

Our Gliderol Warranty applies for the periods (the Applicable Warranty Period) stated as follows:

Gliderol Residential A, AA & B Series Roller Door

Domestic/Residential use – 7 years corrosion free (not within 800metre of a high salt concentration) on door curtain, excludes paint surface rubbing or fading.
3 month warranty on spring tension.
1 year on all components, labour & workmanship, if fitted by an authorised Gliderol Distributor or Gliderol Technician.
Industrial/Commercial use – 1 year on all components, labour & workmanship, if fitted by an authorised Gliderol Distributor or Gliderol Technician.
3 month warranty on spring tension.
1 year on parts only, if fitted by parties other than an authorised Gliderol Distributor or Gliderol Technician.
1 year only if a Non Glidermatic operator is fitted to the door.
Gliderol strongly recommends that the Gliderol residential A, AA &B Series Roller Door be serviced by an authorised Gliderol Distributor or Gliderol Technician
every 24 months to ensure longevity of the products life.

Gliderol Glidermatic GRD+ Heavy Duty & Dual Roller Door Operator
Domestic / Residential use – 5 year parts only warranty on drive unit & motor, 1 year on electronics, limit switches, labour & workmanship. (Excludes
batteries, fuses & lights globes, which have no warranty).
Industrial/Commercial use – not suitable for these applications therefore our Gliderol Warranty will not apply.
1 year on parts only, if fitted by parties other than an authorised Gliderol Distributor or Gliderol Technician.
Gliderol strongly recommends that the Gliderol Glidermatic Heavy Duty & Dual Roller Door Operator be serviced by an authorised Gliderol Distributor or
Gliderol Technician every 18-24 months to ensure longevity of the products life.

Gliderol Glidermatic GRD Industrial Door Operator

Industrial / Commercial use – 1 year on all components, labour & workmanship, if fitted by an authorised Gliderol Distributor or Gliderol Technician. (Excludes
batteries, fuses & lights globes, which have no warranty).
1 year on parts only, if fitted by parties other than an authorised Gliderol Distributor or Gliderol Technician.
Gliderol strongly recommends that the Gliderol Industrial GRD Door Operator be serviced by an authorised Gliderol Distributor or Gliderol Technician every 12
months to ensure longevity of the products life.

Gliderol Rollamatic Door Operator

Domestic / Residential use – 5 year parts only warranty on drive unit & motor, 1 year on electronics, limit switches, labour & workmanship. (Excludes
batteries, fuses & lights globes, which have no warranty).
1 year on parts only, if fitted by parties other than an authorised Gliderol Distributor or Gliderol Technician.
Gliderol strongly recommends that the Gliderol Rollamatic Door Operator be serviced by an authorised Gliderol Distributor or Gliderol Technician every 18-24
months to ensure longevity of the products life.

Product Warranty Conditions

Warranty Conditions
1. Subject to the following specific limitations and exceptions, and in addition to all rights and remedies to which you may be entitled under the Australian
Consumer Law, Gliderol warrants all new doors, motors and electronic components of Gliderol's manufacture, sold and installed by Gliderol, to be free from
defect in workmanship under normal use and service for the Applicable Warranty Period prescribed above.

2. During the Applicable Warranty Period, Gliderol will make good any defect as described in clause 1 above by repairing or replacing the affected product or
part (at its option) PROVIDED THAT notice of any claimed defect in materials or workmanship in or resulting from installation of any door shall have been
given to Gliderol within the period from date of installation as prescribed above.

3. For products sold through or installed by an authorised Gliderol Distributor or other party (other than an accredited Installer Contractor nominated by
Gliderol), our Gliderol Warranty covers only defects of manufacture and does not include:-
• Any defects caused by or related to the installation of that product, nor
• The cost of delivering or re-installing a product that is repaired or replaced.
This limitation does not exclude, restrict or modify any right or remedy to which you may otherwise be entitled in respect of delivery or re-installation under
the Australian Consumer Law or other applicable laws, which may not be excluded.

4. Our Gliderol Warranty does not apply to any defect, loss or damage arising or caused directly or indirectly by or as a result of:-
(i) Any masonry rendered or other surfaces cracking or collapsing during installation of the door
(ii) Any defect or deterioration of timber including drying out after installation
(iii) Any weakening or collapse of the structure to which the doors are affixed occurring any time after installation
(iv) Any damage to or deterioration in the condition of the doors occurring in transit by customer nominated or appointed carrier or occurring after delivery
and prior to installation

(v) Any defect (including defects in component parts or accessories) rising from or attributable to the failure to carry out normal preventive maintenance or
adjustment
(vi) To any additional defect damage or deterioration arising from or attributable to the operation of the door after it is known to be defective

Glidermatic GRD+ Installation Instructions & owner’s manual

 (vii) Any door being installed within 800 metres of the sea or other body of water of equivalent or greater salt concentration or in an area subject to industrial
fall out
(viii) Any fault or surge in customer’s electricity supply
(ix) The door striking an immovable object during travel

Product Warranty Conditions Cont..

5. Items excluded from our Gliderol Warranty are:

(i) Batteries
(ii) Fuses
(iii) Globes
(iv) Sensitivity adjustments
6. Water damage voids the Gliderol Warranty on all electronic components.
7. While Gliderol doors are long lasting and hard wearing under normal conditions our Gliderol Warranty does not extend to inherent defects in steel or other
material used in the manufacture. Gliderol will however, where possible, procure and assign to the customer the benefit of the warranty of the manufacturer
of the steel or other material.
8. If Gliderol has at request of a customer procured painting, powder coating or other surface application to its product, the Gliderol Warranty does not
extend to such painting, powder-coating or other surface application. For this purpose, Gliderol at all times acts as agent of customer. Gliderol may, as a
service to the customer but without any legal obligation to do so, assist customer to obtain redress in respect of any defect.
9. Except as is provided by the Gliderol Warranty and subject to any rights or remedies to which you may be entitled under the Australian Consumer Law or
other applicable law which may not be excluded, , this Gliderol Warranty supersedes and excludes all representations, warranties and conditions whether
expressed or implied by law and Gliderol shall have no liability or otherwise than herein provided for any loss and damage (including consequential loss and
damage, loss of use or profits) by reason of delay, defective or faulty materials or workmanship, negligence or any act, matter or thing done permitted or
omitted to be done by Gliderol.
10. Gliderol reserves the right to touch up on site Colorbond and or pre-painted surfaces on its range of garage doors but, no responsibility will be taken for
the possibility of any paint rubs or scuffing on the internal wash coat finish or external painted surface.
11. To make a claim under our Gliderol Warranty:
(a) if you purchased your product directly from Gliderol, you must send your claim to one of the addresses listed at the end of this warranty; or
(b) if you purchased your product from an authorised Gliderol Distributor or other non-Gliderol entity, you must make your claim through that authorised
Distributor or other non-Gliderol entity.
Proof of purchase MUST be provided at the time of the Gliderol Warranty claim.
Any cost incurred by you in making a claim under our Gliderol Warranty will be borne by you.
12. The Gliderol Warranty is given by:
Name: Gliderol International Pty Ltd
Company address: 32 Jacobsen Crescent, Holden Hill SA 5088
Company telephone number: +61 8 8360 0002
Company email address: [email protected]

CONDITIONS OF SALE AND INSTALLATION DIRECTLY FROM GLIDEROL

1. The following conditions of sale and installation apply only to products sold directly by Gliderol. These conditions do not apply to the sale of products by
authorised Gliderol Distributors or other non-Gliderol entities.
2. THIS IS A QUOTATION ONLY – recommending type and size of doors suitable for the job. Confirmation as an order should be given by customer to Gliderol’s
Representative or to Gliderol’s Office, “in writing” whereupon this quotation shall become a Contract for Sale and where applicable also a contract for
Installation.
3. The details given in the quotation are subject to any alteration or preparation to be carried out by customer as specied on front of this quotation.
4. Where openings are not complete or actual accurate measurements cannot be taken on site, the Gliderol Doors sizes and costs given in this quotation are
estimated only and would be subject to revision when accurate measurements can be taken on completion of the opening.
5. Manufacture of Gliderol Doors will not commence until accurate site measurements are available and can be checked.
6. Where Gliderol Doors are made to suit floor levels, lintel heights or opening sizes guaranteed by the customer, any departure from the given sizes will be
the responsibility of the customer as will any costs involved in alteration of made-up Gliderol Doors.
7. Any delivery, and/or installation dates given are approximate only and Gliderol accepts no liability for delay from any cause whatsoever. If by any reason or
Act of God, war, government or semi-government enactment, regulation or restriction, lock-out, strike, industrial dispute, fire, tempest, flood, failure or
inability to obtain licenses, transport or materials or any other cause beyond Gliderol’s control of delivery or installation is delayed Gliderol may extend the
time of delivery or installation or if Gliderol is unable to deliver or install, the contract shall be voidable at Gliderol’s option with no right to either party for
damage, loss, cost or expense.
8. If these conditions of sale (which shall only be varied, modified or rescinded by written agreement executed by Gliderol) shall differ in any respect from the
customer’s acceptance or confirmation then these conditions shall prevail.
9. This quotation is open for acceptance for a period of 60 days from the date of quotation. Acceptance thereafter will be at the option of Gliderol and subject
to its written agreement.
10. PRICE VARIATION: The prices quoted are based on current list prices for Gliderol Doors and Material and Labour at date of quotation. Any variation in
these prices before completion of the Contract would be to customer’s account.
11. TERMS OF PAYMENT: (i) Unless specfically varied in writing by Gliderol the terms of payment are in full on delivery (ii) If credit is extended the terms of
payment are Nett 7 days. (iii) Default in payment in accordance with invoiced terms for payment will result in the customer becoming liable to pay all
Gliderol's recovery costs and interest fixed at 5% of invoice value. (iv) The customer acknowledges that all right title and interest in the goods particularised
hereon shall remain the property of the vendor Manufacturer until such time as payment in full has been made. At any time after delivery and prior to
payment the vendor, Gliderol shall have the right to enter into and upon any premise upon which the goods may be stored or installed and remove same
without its incurring any liability in relation thereto and the customer hereby appoints the vendor Manufacturer his or her servant agent and attorney for the
such purposes. (v) Deposit is non-refundable if the job is cancelled by the customer/customers’ agent if the door has commenced manufacture.
12. To secure to Gliderol the payment of the price the customer as owner lessee or tenant of the premises hereby charges the customers interest in the
premises with the payment of the price. Gliderol may at any time after (but not before) default by the customer lodge a caveat over the customers interest in
the premises.
13. Any discount applicable will not be granted if the account is unpaid after 7 days.
14. Gliderol does not itself carry out installation but will nominate an accredited Installer Contractor to carry out the work on its behalf. Installation is then a
matter of separate contract with the Installer whose particulars are either provided in this Quotation or will be provided upon confirmation by the customer.
Gliderol has taken all reasonable care to ensure that any Installer Contractor nominated is competent, experienced and skilled in the installation of Gliderol’s
doors. Gliderol will at all times use its influence to ensure any installation complaint is dealt with promptly and resolved to the reasonable satisfaction of the
customer. The customer’s attention is also directed to the terms of the warranty herein.
Product Warranty Conditions Cont..

15. The installation costs cover only the work specified on the quotation and do not, unless specially stated, include rectification of existing out-of-square
openings or removal of old doors and fittings or electricity or gas fittings or the like.
16. Whilst reasonable care will be taken while drilling and fixing, Gliderol and its Installers will not be responsible for the failure, from any cause whatsoever,
of any masonry or rendered surfaces while drilling or fixing by cracking or collapsing.
17. The Term “Take down old doors” or similar words used in this quotation refers only to the taking of old doors off the structure and does NOT in any way
imply removal or taking away of any old doors from the property or of disposing of such doors.

Glidermatic GRD+ Installation Instructions & owner’s manual

Warranty Form
Name Address

Product Type Installation Date

Supplier (Distributor)

Installer Phone No

Address

Installers Signature
NOTE: THIS FORM MUST BE COMPLETED BY THE INSTALLER AND PRODUCED AS PROOF OF PURCHASE DATE WHEN
MAKING A SERVICE CALL UNDER WARRANTY, OTHERWISE SUCH CALLS ARE LIABLE TO SERVICE CHARGES.

FOR SALES AND SERVICE, CONTACT

GLIDEROL INTERNATIONAL PTY LTD ABN 92 007 928 949

Head Office Gliderol Garage Doors

32 Jacobsen Crescent, Holden Hill, SA 5088
Phone (08) 8360 0000 Fax (08) 8261 9700
Victoria Gliderol Garage Doors
23 Kitchen Road, Dandenong, VIC 3175
Phone (03) 9793 5455 Fax (03) 82619700
New South Wales Gliderol Garage Doors
45 Summit Street, Smithfield, NSW 2164
Phone (02) 9725 1033 Fax (02)9725 1115

Queensland Gliderol Garage Doors

241 Elliot Road, Banyo,QLD 4014
Phone (07) 3260 9000 Fax (07) 3260 9055
Western Australia Gliderol Garage Doors
48 Luisini Road Wangara WA, 6065
Phone (08) 9408 4427 Fax (08) 9309 2777

OR YOUR LOCAL SUPPLIER

Glidermatic GRD+ Installation Instructions & owner’s manual